Académique Documents
Professionnel Documents
Culture Documents
NO 1 2 3 4 5 6 7 8 9 10 11
TITLE OBJECTIVE THEORY APPARATUS MATERIAL PROCEDURES RESULT QUESTIONS DISCUSSION CONCLUSION APPENDIX REFERENCE
PAGE 1 1 2 2 3 4 5 6 7 8 9
0|Page
:4 : SILT TEST FOR SAND : To determine amount and percent of silt in a nature sand
THEORY
Silt is granular material of a size somewhere between sand and clay whose mineral origin is quartz and feldspar. Silt may occur as a soil or as suspended sediment (also known as suspended load) in a surface water body. It may also exist as soil deposited at the bottom of a water body.
Clay, mud, fine, dust or silt will weaken the concrete because the dirt tends to coat the aggregate and weaken the bond between the aggregate and cement paste thus preventing the cement from setting. Coarse aggregates should be for cleanliness purposes are inspected by visual inspection.
1|Page
APPARATUS
2|Page
PROCEDURE
1. The cylinder was filled up to about 50 ml of salt water solution. (one tablespoon salt to 1 litre of water) 2. The sand was poured into the cylinder until the level of water reaches 100 ml. 3. More salt water was added until it reaches 150 ml. 4. The cylinders were shakes well. 5. The cylinders were placed on a levelled surface. 6. After 2 hours, the results were recorded. 7. The silt layer was measured on top of the sand. The thickness can be explained as a percentage of sand level below the layer. The sand considered as clean if the percentage is not more than 8% of the original volume of the sand.
3|Page
RESULT
Calculation on amount of silt using Volume method. Measurement (mm) No. Description Sand inside Sand outside the lab the lab 83 mm 4 mm 80 mm 5 mm
1 2
= =
x / y X 100%
Standard form
4|Page
QUESTION 1. Why we use salt water in this test? We use the salt in this test is for separate the water with the sand to measure the silt layer on the top of the sand. If we dont use the salt, we could not measure it as the water did not float or separate with the sand. 2. What happen to you concrete when we use the sand with silt more than 8%? If we use sand with silt more than 8%, the concrete will weak and cannot use it for any project. This is because the silt will weaken the bond between aggregates and cement paste.
5|Page
DISSCUSSION
Silt is created by a variety of physical processes capable of splitting the generally sand-sized quartz crystals of primary rocks by exploiting deficiencies in their lattice. These involve chemical weathering of rock and regulate, and a number of physical weathering processes such as frost shattering and haloclasty. The main process is abrasion through transport, including fluvial combinations, Aeolian attrition and glacial grinding. It is in semi-arid environments that substantial quantities of silt are produced. Silt is sometimes known as "rock flour" or "stone dust", especially when produced by glacial action. Mineralogical, silt is composed mainly of quartz and feldspar. Sedimentary rock composed mainly of silt is known as siltstone.
6|Page
CONCLUSION If the sand contains more than 6% silt, you would have to use more cement and the concrete would shrink more during the hardening process, causing cracks in the product. Silt and clay are not as strong as typical aggregates. They can absorb water and their properties can change because of it. In fresh concrete, I would think that silt and clay would interfere with the bonding of aggregates to cement. In hardened concrete, if the silt and clay come in contact with water in air voids, they can shrink or swell, either building internal pressure (swelling) or leaving larger voids and weakening the concrete (shrinking).
7|Page
APPENDIX
Salt
Salt water
Glass rod
Spatula
8|Page
REFERENCE
http://en.wikipedia.org/wiki/Silt http://autonopedia.org/buildings_and_shelter/Rural_Building/Aggregates.html http://sg.answers.yahoo.com/question/index?qid=20100528053325AAfWt4Y
9|Page