Académique Documents
Professionnel Documents
Culture Documents
BSC6900V900R012
www.huawei.com
Huawei Confidential
interface data configuration in IP networking, including configuration flow, commands and parameters.
Huawei Confidential
Page 2
Huawei Confidential
Page 3
Documentation(V900R012C00_01)-EN
BSC6900 UMTS Initial Configuration
Guide(V900R012C00_01)
Huawei Confidential
Page 4
Chapter 1 Interface configuration Overview in IP Networking Chapter 2 Iub Interface Data Configuration Chapter 3 Iucs/Iups Interface Data Configuration
Huawei Confidential
Page 5
Why IP Network?
3G+MIMO+HSPA+ UL: 12.5 Mbps DL: 28 Mbps LTE UL: 50 Mbps DL: 100 Mbps
20-100 Mbps 10-50 Mbps 3-20 Mbps 64-384 Kbps 384 K5 Mbps
Service Bandwidth
64-144 Kbps
2002-2003
2003-2004
2005-2006
2006-2007
2008-2010
2010-2012
Wireless Mobil network all use IP. Wireless access network needs wider bandwidth. Operators needs lower cost of CAPEX and OPEX.
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential
Page 6
Chapter 1 Interface configuration Overview in IP Networking Chapter 2 Iub Interface Data Configuration Chapter 3 Iucs/Iups Interface Data Configuration
Huawei Confidential
Page 7
User plane
HSDSCH FP USCH FP CPCH FP TFCI2 FP FACH FP PCH FP
NBAP
NCP
CCP
Huawei Confidential
Page 8
End
Huawei Confidential
Page 9
FG2a/GOUa/FG2c/GOUc PEUa
POUa/POUc
Setting the Mapping Between Adjacent Nodes and Transmission Resources
UOIa_IP
End
Huawei Confidential
Page 10
IP1IP2 is the device IP of IP board. IP3IP4 is the IP of Ethernet port. IP5IP6 is the gateway IP on RNC side. IP1IP2 is the IP of Ethernet port.
HUAWEI TECHNOLOGIES CO., LTD.
Page 11
Link aggregation
Link aggregation is to group multiple Ethernet links on the Ethernet
interface board into a logical link, so that all the Ethernet links in the group share the common IP and MAC addresses
The benefits of this feature:
The transmission bandwidth is broadened The reliability is enhanced The load sharing is enabled
Page 12
SET ETHPORT:
ADD ETHIP:
six IP addresses.
Huawei Confidential
Page 13
ADD ETHTRK:
Add a link aggregation group. Add a sub-link to the link aggregation group. Add primary IP address for the link aggregation
ADD ETHTRKLNK:
ADD ETHTRKIP:
Page 14
Huawei Confidential
Page 15
Huawei Confidential
Page 16
Set Board type to PEUa. Set Logic function type to IP. It is recommended that Borrow DevIP be set to YES.
Huawei Confidential
Page 17
SET E1/T1:
SET OPT:
J0 TX Type, J0 TX Value, Expected J0 RX Type, Expected J0 RX Value, J1 TX Type, J1 TX Value, Expected J1 RX type, and Expected J1 RX Value must be consistent with the peer.
SET COPTLNK:
ADD MPGRP
ADD MPLNK
Huawei Confidential
Page 18
SET OPT:
J0 TX Type, J0 TX Value, Expected J0 RX Type, Expected J0 RX Value, J1 TX Type, J1 TX Value, Expected J1 RX type, and Expected J1 RX Value must be consistent with the peer.
Huawei Confidential
Page 19
Mandatory Commands ADD SCTPLNK ADD UNODEB ADD UNODEBALGOPARA ADD UNODEBLDR ADD UNODEBOLC ADD UNCP ADD UCCP ADD ADJNODE
End
Huawei Confidential
Page 20
Huawei Confidential
Page 21
Huawei Confidential
Page 22
First local IP address: In layer 2, this parameter can use the Ethernet port IP of RNC interface board.
First destination IP address: In layer 2, this parameter can use the NodeB port IP.
Destination SCTP port No.: Every SCTP link includes source port and destination port. On RNC
side, we can use SET SCTPSRVPORT to set RNC source port. Ports of Every SCTP link are negotiation data.
Logic port Flag: It is used in RAN sharing. Different operators separate Iub transmission
resource instead of first come first served when admission.
Huawei Confidential
Page 23
Huawei Confidential
Page 24
Use this command to add a RNC pool. Two RNCs with Iur interface can be configured as a RNC pool. The two RNCs supply redundancy backup for each other. For a NodeB, the local RNC acts as the primary RNC and the peer RNC as the secondary RNC. If the primary RNC is faulty, the secondary RNC takes over the traffic carried by the NodeB.
Huawei Confidential
Page 25
This command use to add NodeB algorithm switch. IUB_LDRIUB congestion control algorithm NODEB_CREDIT_LDRNodeB level credit congestion control algorithm LCG_CREDIT_LDRCell group level credit congestion control algorithm Suggest : ON Suggest: OFF Suggest: ON
Huawei Confidential
Page 26
Huawei Confidential
Page 27
Huawei Confidential
Page 28
The SAAL link that bears the NCP link must be of UNI type.
Huawei Confidential
Page 29
Huawei Confidential
Page 30
Setting the Mapping Between Adjacent Nodes and Transmission Resources Adding User panel on the Iub Interface
End
Huawei Confidential
Page 31
By default, 14 transport resource mappings (the index ranges from 0 to 13) are added. In addition, the 14 transport resource mappings cannot be modified and deleted.
Huawei Confidential
Page 32
AF43
AF4 AF42 AF41 AF33 AF3 AF32 AF31 AF23 AF2 AF22 AF21 AF13 AF1 AF12 AF11
38
36 34 30 28 26 22 20 18 14 12 10
BE
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential
0
Page 33
By default, the activation factor table with index 0 is configured in the RNC. In addition, this index cannot be modified and removed.
The RNC uses the activation factor to calculate the admission bandwidth. The admission bandwidth is calculated by using the following formula: Admission bandwidth = Bandwidth at the transport layer * Activation factor/100.
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential
Page 34
If the NodeB supports ATM/IP dual stack or hybrid IP, you can configure the path load EQ threshold table. The path load EQ threshold table with index 0 is the default table in the RNC, and it cannot be modified or deleted.
Huawei Confidential
Page 35
This command is used to configure the TRM mapping table and activity factor table for users of different priorities. When Interface Type is IUB, Resource Management Mode can be SHARE or EXCLUSIVE. When Interface Type is IU-CS,IU-PS,IUR, Resource Management Mode can only be SHARE.
Huawei Confidential
Page 36
End
Huawei Confidential
Page 37
Perform this step when the RAN sharing function is used. If the user plane resources on the Iub interface are EXCLUSIVE, set
Resource Management Mode to EXCLUSIVE and set CN Operator Index.
Huawei Confidential
Page 38
LST PHBMAP: to query the configuration data about the mapping from the PHB to the DSCP.
Huawei Confidential
Page 39
End
Page 40
This command is used to add the OM IP address of NodeB and build an IPRT
to NodeB OM IP on BAM automatically.
Huawei Confidential
Page 41
Huawei Confidential
Page 42
Huawei Confidential
Page 43
Function: Use this command to detect the ID of the VLAN where the NodeB belongs. Note: 1. When the detect type is set to ALL, only the current configured NodeBs are detected. However, if another NodeB is added after the detection, the detection for this added NodeB must be started. 2. Before executing this command, ensure that the VLAN IDs of the OM IP address and the PORT IP for the NodeB have been configured.
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential
Page 44
Chapter 1 Interface configuration Overview in IP Networking Chapter 2 Iub Interface Data Configuration Chapter 3 Iucs/Iups Interface Data Configuration
Huawei Confidential
Page 45
Huawei Confidential
Page 46
Huawei Confidential
Page 47
Start
ADD SCTPLNK ADD M3LKS ADD M3RT ADD M3LNK ADD ADJNODE : ADD UCNDOMAIN ADD UCNNODE
End
Huawei Confidential
Page 48
Huawei Confidential
Page 49
Example 2
M3LKS
M3LE
CN
M3DE
RNC
M3LE
CN
M3DE
IPSP
IPSP
ASP
SGP
SP
IPSP
IPSP
IPSP server=SGP
SGP
ASP
Huawei Confidential
Page 50
Huawei Confidential
Page 51
Adding Physical Layer and Data Link Layer Data Adding Control Plane Data
ADD TRMMAP ADD TRMFACTOR ADD ADJMAP The same as Iub interface
End
Huawei Confidential
Page 52
Huawei Confidential
Page 53
1.
Please think of the configuration flow and commands of Interface configuration in RNC initial configuration.
2. 3.
Please think how to configure ATM&IP dual stack on Iub interface? Please think how to configure hybrid IP on Iub interface?
Huawei Confidential
Page 54
Thank you
www.huawei.com