Académique Documents
Professionnel Documents
Culture Documents
Pty Ltd
MUL TI F LO P U M PS
By MULTIFLO
AUSTRALIA
Pty. Ltd.
MULTIFLO offers a high quality range of products. These include the MULTIFLO range of vacuum primed diesel and electric driven pump sets that can be custom-built to ensure the very best performance for your operation, and survive under the toughest of operating conditions. MULTIFLO Pump Units were first produced in 1976, designed and manufactured to provide a better and more reliable alternative to efficiently pump clean the open cut coal mining pits at the time. To secure a market place, formation of a pump hire division was put in place using products ex works, this enabled the company to be actively involved with development and requirements of setting in place mine pit dewatering systems in the open cut mining area. Having achieved this mark, MULTIFLO entered into the open cut mining industry with a range of diesel and electric driven vactronicTM vacuum primed pump sets capable of pumping not only water against high head situations, but also large quantities of slurry from the open pits.
Further information on the company and products may be obtained by contacting the Caloundra office, thus enabling our office to connect you with the MULTIFLO representative best able to work with you on your project.
MUL TI F LO P U M PS
By MULTIFLO
AUSTRALIA
Pty. Ltd.
MUL TI F LO P U M PS
By MULTIFLO
AUSTRALIA
Pty. Ltd.
MODEL MFC-120
GENERAL INFORMATION
100 x 100 single stage centrifugal Type 120MS Frame Size - 2A Seal - Mechanical Passage Size - 50 mm
CONSTRUCTION
Pump Casing - Cast Iron Impeller - Stainless Steel Shaft - 431 Stainless Steel ** For aggressive water applications, all wetted parts are available in stainless steel
ENGINE OPTIONS
Caterpillar 3024 Deutz F3L1011F Hatz 2L41C 23 kW 23 kW 18.8 kW (Max 1800RPM)
PERFORMANCE
Maximum Flowrate Shutoff Head - 60 litres per second - 36 metres
DIMENSIONS/CAPACITIES/WEIGHTS
Height Length Width Weight Dry Weight Wet Fuel Capacity 1135 mm 2250 mm 1000 mm 1140 kg 1300 kg 160 litres
MUL TI F LO P U M PS
By MULTIFLO
AUSTRALIA
Pty. Ltd.
MUL TI F LO P U M PS
By MULTIFLO
AUSTRALIA
Pty. Ltd.
MODEL MFC-140
GENERAL INFORMATION
150 x 150 single stage centrifugal Type 140MS Frame Size - 4A Seal - Gland Packing or Mechanical Seal Passage Size - 50 mm
CONSTRUCTION
Pump Casing - Cast Iron Impeller - Stainless Steel Shaft - 431 Stainless Steel ** For aggressive water applications, all wetted parts are available in stainless steel
ENGINE OPTIONS
Caterpillar 3054 Deutz F3L912 Hatz 3L41C 49 kW 30 kW (Max 1800RPM) 30 kW (Max 1800RPM)
PERFORMANCE
Maximum Flowrate Shutoff Head 80 litres per second 50 metres
DIMENSIONS/CAPACITIES/WEIGHTS
Height Length Width Weight Dry Weight Wet Fuel Capacity 1470 mm 2800 mm 1132 mm 1650 kg 2230 kg 580 litres
MUL TI F LO P U M PS
By MULTIFLO
AUSTRALIA
Pty. Ltd.
MUL TI F LO P U M PS
By MULTIFLO
AUSTRALIA
Pty. Ltd.
MODEL MFC-160
GENERAL INFORMATION
150 x 150 single stage centrifugal Type 160 Frame Size - 4A Seal - Gland Packing or Mechanical Seal Passage Size - 50 mm
CONSTRUCTION
Pump Casing - Cast Iron Impeller - Stainless Steel Shaft - 431 Stainless Steel ** For aggressive water applications, all wetted parts are available in stainless steel
ENGINE OPTIONS
Caterpillar 3054NA Cummins B3,3T Deutz F4L912 Hatz 4L41C 51 kW 49 kW 41 kW (Max 1800RPM) 42 kW (Max 1800RPM)
PERFORMANCE
Maximum Flowrate Shutoff Head 90 litres per second 55 metres
DIMENSIONS/CAPACITIES/WEIGHTS
Height Length Width Weight Dry Weight Wet Fuel Capacity 1470 mm 2800 mm 1132 mm 1650 kg 2230 kg 580 litres
MUL TI F LO P U M PS
By MULTIFLO
AUSTRALIA
Pty. Ltd.
MU L TI F P U U LT IF LLO O PU M PM S PS
By By MULTIFLO
AUSTRALIA
MODEL MFC-180
GENERAL INFORMATION
200 x 200 single stage centrifugal 180G Frame Size - 5AA Gland Conventional packed, oil lubricated Using a controlled drip feed system Passage Size - 25 mm
CONSTRUCTION
Pump Casing - Cast Iron Impeller - Stainless Steel Shaft - 431 Stainless Steel ** For aggressive water applications, all wetted parts are available in stainless steel
ENGINE OPTIONS
Caterpillar 3056T 110 kW 101 kW Cummins 6BTA5.9 -
PERFORMANCE
Maximum Flowrate Shutoff Head 140 litres per second 55 metres
DIMENSIONS/CAPACITIES/WEIGHTS
Height Length Width Weight Dry Weight Wet Fuel Capacity 1675 mm 3450 mm 1495 mm 2900 kg 4000 kg 1100 litres
MU L TI F P U U LT IF LLO O PU M PM S PS
By By MULTIFLO
AUSTRALIA
MU L TI F P U U LT IF LLO O PU M PM S PS
By By MULTIFLO
AUSTRALIA
MODEL MFC-290
GENERAL INFORMATION
200 x 150 single stage centrifugal Type 290MS Frame Size - 5AA Seal - Gland or Mechanical [Silicon Carbide/Tungsten] Passage Size - 45 mm
CONSTRUCTION
Pump Casing - Cast Iron Impeller - Stainless Steel Shaft - 431 Stainless Steel
** For aggressive water applications, all wetted parts are available in stainless steel
ENGINE OPTIONS
Caterpillar 3056TA Cummins 6BTA5.9 -
PERFORMANCE
110 kW 101 kW Maximum Flowrate Shutoff Head - 103 litres per second - 85 metres
DIMENSIONS/CAPACITIES/WEIGHTS
Height Length Width Weight Dry Weight Wet 1675 mm 3450 mm 1495 mm 2900 kg 4000 kg
MU L TI F P U U LT IF LLO O PU M PM S PS
By By MULTIFLO
AUSTRALIA
MU L TI F P U U LT IF LLO O PU M PM S PS
By By MULTIFLO
AUSTRALIA
MODEL MFC-345
GENERAL INFORMATION
200 x 150 single stage centrifugal Type 345G Frame Size - FF Gland Conventional packed, oil lubricated Using a controlled drip feed system. Passage Size 140 mm
CONSTRUCTION
Pump Casing - Ultrachrome 28% Cr (A49) Impeller - Ultrachrome 28% Cr (A49) Shaft - CS 1045 Carbon Steel Sleeve Fully Hardened Type 420C ** For aggressive water applications, all wetted parts are available in stainless steel
ENGINE OPTIONS
Caterpillar 3406TA Cummins N14-450 328 kW
PERFORMANCE
Maximum Flowrate 260 litres per second 106 metres 317 kW (Max 1800 RPM) Shutoff Head
DIMENSIONS/CAPACITIES/WEIGHTS
Height Length Width Weight Dry Weight Wet Fuel Capacity 3100 mm 5800 mm 2000 mm 9680 kg 12000 kg 2320 litres
MU L TI F P U U LT IF LLO O PU M PM S PS
By By MULTIFLO
AUSTRALIA
MU L TI F P U U LT IF LLO O PU M PM S PS
By By MULTIFLO
AUSTRALIA
MODEL MFC-360
GENERAL INFORMATION
200 x 150 single stage centrifugal Type 360G Frame Size - 6A Gland Seal Conventional packed, oil lubricated using a controlled drip feed system. Passage Size 45 mm
CONSTRUCTION
Pump Casing - T220 Grey Cast Iron Impeller - 316 Stainless Steel Shaft - 1040 Shaft Steel Shaft Sleeve 431 Stainless Steel ** For aggressive water applications, all wetted parts are available in stainless steel
ENGINE OPTIONS
Caterpillar 3126TA Cummins 6CTA8.3 166 kW 157 kW
PERFORMANCE
Maximum Flowrate Shutoff Head - 100 litres per second - 126 metres
DIMENSIONS/CAPACITIES/WEIGHTS
Height Length Width Weight Dry Weight Wet Fuel Capacity 2460 mm 5650 mm 1800 mm 6500 kg 7800 kg 1800 litres
MU L TI F P U U LT IF LLO O PU M PM S PS
By By MULTIFLO
AUSTRALIA
MU L TI F P U U LT IF LLO O PU M PM S PS
By By MULTIFLO
AUSTRALIA
MODEL MFC-380
GENERAL INFORMATION
200 x 150 single stage centrifugal Type 380G Frame Size - 6A Gland Seal Conventional packed, oil lubricated Using a controlled drip feed system. Passage Size - 45 mm
CONSTRUCTION
Pump Casing - T220 Cast Iron Impeller - 316 Stainless Steel Shaft - CS1040 Carbon Steel Sleeve 431 Stainless Steel ** For aggressive water applications, all wetted parts are available in stainless steel
ENGINE OPTIONS
Caterpillar C9 @ 1700 RPM B Rating - 219 kW Cummins M11-350 @ 1700 RPM Water Management Rating - 229 kW
PERFORMANCE
Maximum Flowrate Shutoff Head - 155 litres per second - 110 metres
DIMENSIONS/CAPACITIES/WEIGHTS
Height Length Width Weight Dry Weight Wet Fuel Capacity 2750 mm 5650 mm 1800 mm 6500 kg 7800 kg 1800 litres
MU L TI F P U U LT IF LLO O PU M PM S PS
By By MULTIFLO
AUSTRALIA
MU L TI F P U U LT IF LLO O PU M PM S PS
By By MULTIFLO
AUSTRALIA
MODEL MFC-385
GENERAL INFORMATION
200 x 150 single stage centrifugal Type 385G Frame Size - 6A Gland Seal Conventional packed, oil lubricated Using a controlled drip feed system. Passage Size - 45 mm
CONSTRUCTION
Pump Casing - T220 Cast Iron Impeller - 316 Stainless Steel Shaft - CS1040 Carbon Steel Sleeve 316 Stainless Steel ** For aggressive water applications, all wetted parts are available in stainless steel
ENGINE OPTIONS
Caterpillar 3406TA Cummins N14-450 328 kW 317 kW
PERFORMANCE
Maximum Flowrate Shutoff Head - 160 litres per second - 130 metres
DIMENSIONS/CAPACITIES/WEIGHTS
Height Length Width Weight Dry Weight Wet Fuel Capacity 3030 mm 5750 mm 2100 mm 5100 kg 6500 kg 1800 litres
MU L TI F P U U LT IF LLO O PU M PM S PS
By By MULTIFLO
AUSTRALIA
MU L TI F P U U LT IF LLO O PU M PM S PS
By By MULTIFLO
AUSTRALIA
MODEL MFC-390
GENERAL INFORMATION
200 x 150 single stage centrifugal Type 8/6 FF-HX Slurry Pump Frame Size - FF Gland Seal - Conventional packed, oil lubricated using a controlled drip feed method. Passage Size 65 mm
CONSTRUCTION
Pump Casing - Ultrachrome 28% Cr (A49) Impeller - Ultrachrome 28% Cr (A49) Shaft - CS 1045 Carbon Steel Sleeve Fully Hardened Type 420C ** For aggressive water applications, all wetted parts are available in stainless steel
ENGINE OPTIONS
Caterpillar 3406TA Cummins N14-450 328 kW 317 kW
PERFORMANCE
Maximum Flowrate Shutoff Head - 190 litres per second - 120 metres
DIMENSIONS/CAPACITIES/WEIGHTS
Height Length Width Weight Dry Weight Wet Fuel Capacity 2998 mm 6096 mm 2032 mm 9800 kg 13900 kg 4000 litres
MU L TI F P U U LT IF LLO O PU M PM S PS
By By MULTIFLO
AUSTRALIA
MU L TI F P U U LT IF LLO O PU M PM S PS
By By MULTIFLO
AUSTRALIA
MODEL MFC-420
GENERAL INFORMATION 200 x 150 single stage centrifugal Type 8/6 FF-HX Slurry Pump Frame Size - FF Gland Seal - Conventional packed, oil lubricated using a controlled drip feed system. Passage Size - 50 mm
CONSTRUCTION Pump Casing - Ultrachrome 28% Cr (A49) Impeller - Ni-Cr-Mo Steel (A25) Shaft - CS 1045 Carbon Steel Sleeve Fully Hardened Type 420C ** For aggressive water applications, all wetted parts are available in stainless steel
DIMENSIONS/CAPACITIES/WEIGHTS Height Length Width Weight Dry Weight Wet Fuel Capacity 3378 mm 7500 mm 2400 mm 12260 kg 16260 kg 4012 litres Page 23 Multiflo Pump Products Catalogue
MU L TI F P U U LT IF LLO O PU M PM S PS
By By MULTIFLO
AUSTRALIA
MUL TI F LO P U M PS
By MULTIFLO
AUSTRALIA
Pty. Ltd.
MODEL MFVM-790
GENERAL INFORMATION Two x 150 x 100 single stage centrifugal pumps Type Slurry AH Frame Size - RYFC Gland Seal - Conventional packed, oil lubricated using a controlled drip feed system. Passage Size - 32 mm
CONSTRUCTION Pump Liner - Wear Resistant White Iron Impeller - Duplex Stainless Steel Shaft - CS1040 Carbon Steel Sleeve Stainless Steel ** For aggressive water applications, all wetted parts are available in stainless steel
PERFORMANCE - Series Configuration Maximum Flowrate Shutoff Head - 120 litres/second - 250 metres
DIMENSIONS/CAPACITIES/WEIGHTS Height Length Width Weight Dry Weight Wet Fuel Capacity 2940 mm 5500 mm 2100 mm 9800 kg 12400 kg 2600 litres
PERFORMANCE - Parallel Configuration Maximum Flowrate Shutoff Head - 240 litres/second - 125 metres
H (m)
50%
40%
60%
Series configuration
2200 RPM
2100
70%
250
75%
80%
200
80%
6m 7m
2000
3m NPSH
81%
4m 5m
150
100
0 H (m)
20
40
60
80
Q (l/s)
100
120
140
160
Parallel configuration
50%
40%
60%
125
2200 RPM
2100
70%
75%
80%
100
1900
80%
2000
3m NPSH
81%
1800 1700
75
50
40
80
120
160
Q (l/s)
200
240
280
320
75%
75%
4m
5m
6m 7m
MU L TI F P U U LT IF LLO O PU M PM S PS
By By MULTIFLO
AUSTRALIA
SPECIFICATIONS
SPECIFICATIONS FOR A MULTIFLO DIESEL DRIVEN, VACUUM PRIMED, HIGH PERFORMANCE PUMP UNIT.
ENGINE CONTROL The control panel is manufactured from stainless steel and is fitted with the following equipment: Hour Meter Engine Start Switches Vactronic Control Module Run Relays Circuit Breakers ELECTRICAL SYSTEM The engine has a 12 or 24 volt start and charge system and the pump unit is fitted with one or two 12 volt Caterpillar batteries. The electrical system features the following: Circuit breakers in place of fuse holders Wiring mechanically protected by Adaptaflex PAF21 conduit Wiring to A.S. 3000 ENGINE PROTECTION Electrical safety shutdown system for: High engine temperature Low oil pressure DRIVE COUPLING Fenner flexible tyre type coupling complete with Taper-Lock bushes. SUCTION LIFT The unit has a N.P.S.L. (nett positive suction lift) of 9 metres. To obtain maximum performance it is advisable to install the pump unit as close as is practical to the level of fluid being pumped.
AUTO VACUUM PRIME SYSTEM Vactronic electronically controlled, solid state, fully sealed system. Vacuum control operates via activation of a sensor probe located in the vacuum tank chamber. Vactronic system eliminates all mechanically moving parts in the vacuum tank chamber (i.e. float ball and valves). The unit is fitted with a non-return valve at the discharge point of the pump and does not require a foot valve for priming. BARE SHAFT PUMP SAFETY SHUTDOWN Automatic engine shutdown after 2-8 minutes of operation without fluids. Shut down is activated by another sensor probe (delay timer preset to 6 minutes). System acts as safety protection for both the bare shaft pump and mechanical seal. The pump unit may be used to operate under snore conditions. HIGH LIFT VACUUM TANK The vacuum tank is manufactured from 6 mm mild steel incorporating a water and air separator chamber, designed to give maximum air separation, allowing an uninterrupted flow to the bare shaft pump. The vacuum tank is also complete with a vacuum water trap and back up Krundimendt Safety Check Valve to give maximum protection to the vacuum pump under all operating conditions.
MU L TI F P U U LT IF LLO O PU M PM S PS
By By MULTIFLO
AUSTRALIA
SPECIFICATIONS
Continued
SPECIFICATIONS FOR A MULTIFLO DIESEL DRIVEN, VACUUM PRIMED, HIGH PERFORMANCE PUMP UNIT.
VACUUM PUMP The vacuum pump is a 37 C.F.M. air-cooled rotary vane type fully sealed unit - self contained oil lubrication with a two litre capacity. Operating at 1800 RPM maximum and driven by two "Z" section vee belts from the pump input shaft. The vacuum pump is fitted with a 12 or 24 volt solenoid valve to close off flow to the vacuum pump after priming. The Vactronic control module controls the opening and closing of the valve. or The vacuum pump is a 58 C.F.M. air-cooled rotary type fully sealed unit self contained oil lubrication with a 2 litre capacity. Operating at 1800 RPM maximum and driven by two "B" section vee belts from the pump input shaft. The vacuum pump is fitted with a 12 volt solenoid valve to close off flow to the vacuum pump after priming. The Vactronic control module controls the opening and closing of the valve. PAINT Steel Preparation All exterior steel work is abrasive blast cleaned in accordance with A.S.1627 1974, Part 4 - Class 2 1/2. The first coat of paint is International Intergard 475 HSE High Build Epoxy with a thickness of 150-250 micrometers dry. The second and finish coat is International Interfine 629 with a finished thickness of 50-75 micrometers dry. (Total finished thickness 200-325 micrometers). Colour to be Caterpillar Yellow STEEL/WELDING STANDARD All steel work is to A.S.1204 grade, 250 U.N.O. All welds are minimum 6 mm continuous fillet, in accordance with A.S.1554, Category S.P. PROOF PLATE Securely attached alloy plate stating Unit Weight.
MULTIFLO AUSTRALIA PTY LTD is the owner of properties incorporating intellectual design data, specifications and instructions compiled in this presentation. They must not be used, reproduced or copied in whole or in part, in any form or by any means, nor may the information therein contained, which is confidential to MULTIFLO AUSTRALIA PTY LTD be disclosed to any person, without the prior written consent of MULTIFLO AUSTRALIA PTY LTD. This presentation has been delivered and received on the express conditions that it may be used only for the specific purpose for which it has been provided, may not be used in any way which may injure or cause loss directly or indirectly to MULTIFLO AUSTRALIA PTY LTD or any related corporation and will be returned to MULTIFLO AUSTRALIA PTY LTD immediately on completion of the task for which it has been provided, or on demand.
MU L TI F P U U LT IF LLO O PU M PM S PS
By By MULTIFLO
AUSTRALIA
Trailer Chassis
The trailer chassis is designed to be bolted on to any of the Multiflo pump units. The trailer chassis is designed to be towed with the correct size vehicle to suit the weight and size of the pump unit. The trailer chassis enables the pump unit to be moved from one pumping location to another with ease. The trailer chassis is fitted with the following items:
Dual heavy duty axle The correct wheels to suit the size and weight of the pump unit Brakes can be electrical or mechanical (optional) Tow hitch to suit customer requirements
MU L TI F P U U LT IF LLO O PU M PM S PS
By By MULTIFLO
AUSTRALIA
Four lifting points Two tow lugs Supa alloy tow chains Replaceable wear plate Heavy duty pushbar
MU L TI F P U U LT IF LLO O PU M PM S PS
By By MULTIFLO
AUSTRALIA
The heavy duty skid mounted pontoon unit is designed to float any of the Multiflo pump units. The pontoon is designed to be pushed with bull dozers or excavators. The skid runners enable pump units mounted on the heavy duty pontoon to be towed from one pumping location to another on minesite. The heavy duty skid mounted pontoon is fitted with following items:
Skid runners fabricated from rectangular hollow section (RHS) Four lifting points Two tow lugs Supa alloy tow chains Replaceable wear plate Heavy duty pushbar
MU L TI F P U U LT IF LLO O PU M PM S PS
By By MULTIFLO
AUSTRALIA
MU L TI F P U U LT IF LLO O PU M PM S PS
By By MULTIFLO
AUSTRALIA
Special Projects
MU L TI F P U U LT IF LLO O PU M PM S PS
By By MULTIFLO
AUSTRALIA
MUL TI F LO P U M PS
By MULTIFLO
AUSTRALIA
Pty. Ltd.
MU L TI F P U U LT IF LLO O PU M PM S PS
By By MULTIFLO
AUSTRALIA
Multiflo Head OFFICE MULTIFLO AUSTRALIA PTY LTD Address: 4 Daniel Street Caloundra 4551 Queensland AUSTRALIA
Postal Address:
Telephone:
Fax:
Email:
multiflo@multiflo.com.au
Website:
www.multiflo.com.au
Contacts:
Mr Peter Smit Mr Bryan Fulwood Mr Geoff Way Mr Brad Fleming Miss Sandra Bayley
General Manager - Manufacturing / Sales General Manager - Development Operations Manager Technical Advisor Accounts Administrator
Revised 04/07
Disclaimer: Multiflo Australia Pty Ltd will not be liable for any claims or damages arising out of or in
respect to the supply and or manufacture of this product including, but not limited to, claims for faulty design, negligent or misleading advice, damages arising from loss or use of its products, and any direct, special or consequential damages or injury to any person, corporation or other entity.