This document provides information to calculate the design mix for a 350 psi concrete, including material properties, design requirements, and calculations of batch weights per cubic meter. The concrete mix uses Type I cement and has a specified maximum water-cement ratio of 1.0500 and slump of 160 mm. The calculations determine the cement factor is 4.0 bags/m3, with cement, water, fine aggregate, coarse aggregate, and total batch weights per cubic meter.
This document provides information to calculate the design mix for a 350 psi concrete, including material properties, design requirements, and calculations of batch weights per cubic meter. The concrete mix uses Type I cement and has a specified maximum water-cement ratio of 1.0500 and slump of 160 mm. The calculations determine the cement factor is 4.0 bags/m3, with cement, water, fine aggregate, coarse aggregate, and total batch weights per cubic meter.
This document provides information to calculate the design mix for a 350 psi concrete, including material properties, design requirements, and calculations of batch weights per cubic meter. The concrete mix uses Type I cement and has a specified maximum water-cement ratio of 1.0500 and slump of 160 mm. The calculations determine the cement factor is 4.0 bags/m3, with cement, water, fine aggregate, coarse aggregate, and total batch weights per cubic meter.
Wall Date/Time : S1 Agg. 2.872 Absorption,% : 0.657 Unit wt. Rodded, Kg/cu.m: 1855 Type & Brand of Cement: Type I 100 Type & Brand of Admixture Dosage 0.0% 160 25 Nominal Aggregate Size = = 4.0 160 1.0500 0.9000 168 0.0508 0.1680 18.0% 0.18 0.0% 0.0 0.0000 0.3988 0.6012 65 -5 60.0 1120 0.3901 0.2111 587 0.024 34.39 0.024 0.024 0.024 4.00 0.096 0.024 160 3.840 0.024 0.024 Water,kg 168 4.032 0.024 Fine agg.,kg 587 14.091 0.024 Coarse agg.,kg S1 Agg. 1120 26.887 0.024 0 0 0.000 0.024 Additives,kg 0.0 0.000 2035 48.9 8.25 Prepared by : Calculation of Design Mix by ACI 211.1 Material Properties: Fine agg. Source: Coarse agg. Source: Concrete used for: Specific Gravity (SSD): 2.781 Specific Gravity (SSD): Fineness Modulus : 2.810 Maximum Size : Blending of Aggregates (%) Specific Gravity of Admixture: 1.07 by weight of binder 1.286 Absorption,%: 1549 Unit wt. Rodded kg/m3 Specified max. w/c ratio : 1.0500 Specified max. slump,mm. : Design Specification Requirements : Strenght at 28 days, Mpa : 350 (+) Min. Cement content, kg/cu.m. : a. Cement factor : bags/m3 S-1 Calculation of Batch Weight per Cubic Meter: Target strenght 21 (+) b. Cementitious Materials, kg c. W/C ratio (from ACI) d. Adjusted W/C Ratio Target slump 25 h. Entrapped air,% (from ACI) I. Vol. Of air, m3 j. Admixture dosage e. Mixing water, kg f. Cementitious Materials vol.,m3 g. Vol. Of water ,m3 p. Vol. Of CA & FA, m3 q. Vol. 0f coarse agg, % r. Adjusted CA & vol. By increase ,% k. Admixture ,kg m.Admixture ,m3 n. Vol. Of paste, m3 w. Wt. Of fine agg., kg x. S/A (%) Batch Weight, kg/m3: s. Adjusted vol. Of CA ,% t. Wt. Of course agg. Kg u. Vol. Of course agg.,m3 v. Vol. Of fine agg., m3 Jay Alvin D. Denoyo Cement factor bags/m3 Cement,kg Total Page 1