nego EEL LLL
‘Third Semester =
f i
Mechanical Engineering.) w J}
RY
‘ME 2203/ME 35/10122 ME 404/ME 1202 4080120010.
MACHINERY
(Regulation 2008/2010) \
=
(Common to PTME 2203 — Kinematics of malaise toh E, (Part-Time) Third
Semester Mechanical Engineering ~ Regulation 2009)
Ref RT
NC ~ LY
™~ YY
‘Time : Three hours D. SS 7
Answe ALL pais
Maximum : 100 marks
ea 402 = 20 marks)
1. What is meant by caer
re
2. State the Gifforence between thechaniem and structure.
“Ss
3. Write about rubbing velo.
p
Write down the LEE for finding the number of instantaneous centres in
a =e a
i ae What isthe condition stated by the law of gearing?
List down the laws of friction,
‘YO. _ Distinguish between open and cross belt drive in terms ofits application.PART B — (5 x 16 = 80 marks)
11. (a) Explain the inversions of Four bar chain with examples.
Or
(b) Sketch and explain the following:
(@ Elliptical trammel
(ii) Scotch yoke mechanism.
12. (a) The following data refer to the:dimensions of the links
mechanism: AB = 50 mm; BC = 66 mm; CD = 56 mm and AD ified fink)
= 100 mm. At the instant when Z DAB = 60°, the link AB has an
angular yelocity of 10.5 rad/s in the counter clo ise irection.
Determine the velocity of point C, velocity of point)E on link I ‘BC while
BE = 40 mm and the angular velocities of the links BC -andCD. Also
sketch the mechanism and indicate the data.
Or
(b) A single slider-crank mechanism is shown ima, Determine the
acceleration at B & E and the angular acaipeton the link AB. The
crank rotates at 20 rad/s counter-clockwise, |) ~~
18. (@) A cam with a mifjimam axe of 25 mm, rotating clockwise at uniform
speed of 300 pm is to/he designed to give motion to a flat faced
mushroom follower as detailed below:
@ Toraise throng distance of 25 mm in 120° rotation of the cam
i) Tysenain are at rést for the next 30°
a “during further 120° rotation of the cam
Giyy/ Teredbain inthe same poeitian during est ofthe revelution.
\\raising of the follower takes place with eycloidal motion and the
g with uniform acceleration and retardation. However, the
mh acceleration is 2/3rd of the uniform retardation. Draw the
ines diagram and profile of the cam,
Or
2 2155914,
15.
(a)
(b)
(a)
the retardation during the lift, determine the following: A
Gi) The principal dimensions of the cam Nf <
(ii) The acceleration at the main points. St
Also determine the maximum acceleration and deceleration during the ‘~
lift, VA
im
With the help ofa neatly drawn sketch of a spur Bear, explain elaborately.
the nomenclature of gears, rs
Or
An epieyelic gear train is shown in Fig. 14(b). The input Shas 24 teeth.
Gears P and C constitute a compound planet having 30 and 18\teeth
Tpspectively. Ifall the gears are of the same pitch, find the
the gear train assuming A to be fixed. ~
yt
Fig. 14 on is)
@ A friction clutch of multi-plate type is meant for transmitting a
Power of 65 KW at 1800\tpm. Coefficient of friction for the friction
surfaces is 0.1. /4 intensity of pressure is not to
exceed 160 AN /m?. ‘The intafnal radius is 80 mm and is 0.7 times
the external radiua: rmine the number of plates needed to
transmit the required torque. (10)
Gi) A vertical shaft of 180 am diameter rotating at 150 rpm, rests on a
flat end
step beating. The coefficient of friction is equal to 0.05.
es vertical load of 15 KN, Find the power lost in
sssuming the following conditions:
(D /Uniform pressure @)
(3))
@
Gi)
Find the power transmitted by a belt running over a pulley 700 mm__
diameter at 900 rpm, 14 = 0.3 and angle of lap 160° and maximuge ~~
tension in the belt is 2.453kN. eS FO ay
A simple brake as shown in Fig 15 (b) (i) s used on a shaft edtrying~>/
a flywheel of mass 450 Kg. The radius of gyration of the flywheel ia_,”
500 mm. and runs at 320 rpm. The coefficient of friction is 0.2 and/
the diameter of brake drum is 250 mm, Determineithe following: 5
(2) Torque applied due to a hand load of 150 N Ny @
(2) The number of turns of the wheel before it if brought 2 rest.
DiI > @
}
(3) The time required to bring it to rest/from the moment of
application of the brake. \ @
21559