Académique Documents
Professionnel Documents
Culture Documents
BT3807U/BT3850U
SERVICE MANUAL
US Model
MEX-BT38UW/BT3800U
Canadian Model
AEP Model
UK Model
MEX-BT3800U
Russian Model
MEX-BT3807U
E Model
MEX-BT3850U
Photo: MEX-BT3800U
MEX-BT3700U/BT3750U/BT4700U
CD Mechanism Type
MG-101Z-188//Q
DAX-25A
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS
%78:%7886
&DQDGLDQPRGHOV
CEA2006 Standard
Power Output: 17 Watts RMS 4 at
4 Ohms < 1% THD+N
SN Ratio: 82 dBA
(reference: 1 Watt into 4 Ohms)
Tuner section
FM
Tuning range: 87.5 107.9 MHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 150 kHz
Usable sensitivity: 10 dBf
Selectivity: 75 dB at 400 kHz
Signal-to-noise ratio: 70 dB (mono)
Separation: 40 dB at 1 kHz
Frequency response: 20 15,000 Hz
AM
Tuning range: 530 1,710 kHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 25 kHz
Sensitivity: 26 V
Tuner section
%78$(38.
FM
Tuning range: 87.5 108.0 MHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 150 kHz
Usable sensitivity: 10 dBf
Selectivity: 75 dB at 400 kHz
Signal-to-noise ratio: 70 dB (mono)
Separation: 40 dB at 1 kHz
Frequency response: 20 15,000 Hz
MW/LW
Tuning range:
MW: 531 1,602 kHz
LW: 153 279 kHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 25 kHz
Sensitivity: MW: 26 V, LW: 45 V
Tuner section
%78
Tuner section
%786DXGL$UDELDPRGHO
FM
FM
Tuning range:
)0)0 87.5 108.0 MHzDWN+]VWHS
)00+]DWN+]VWHS
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 150 kHz
Usable sensitivity: 10 dBf
Selectivity: 75 dB at 400 kHz
Signal-to-noise ratio: 70 dB (mono)
Separation: 40 dB at 1 kHz
Frequency response: 20 15,000 Hz
Tuning range:
87.5 108.0 MHz (at 50 kHz step)
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 150 kHz
Usable sensitivity: 10 dBf
Selectivity: 75 dB at 400 kHz
Signal-to-noise ratio: 70 dB (mono)
Separation: 40 dB at 1 kHz
Frequency response: 20 15,000 Hz
MW/LW
Tuning range:
531 1,602 kHz (at 9 kHz step)
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 25 kHz
Sensitivity: 26 V
Tuning range:
MW: 531 1,602 kHz
LW: 153 279 kHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 25 kHz
Sensitivity: MW: 26 V, LW: 45 V
AM
Tuning range:
531 1,602 kHz (at 9 kHz step)
530 1,710 kHz (at 10 kHz step)
AM tuning interval: 9 kHz/10 kHz switchable
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 25 kHz
Sensitivity: 26 V
AM
CD Player section
Signal-to-noise ratio: 120 dB
Frequency response: 10 20,000 Hz
Wow and flutter: Below measurable limit
Wireless Communication
Communication System:
Bluetooth Standard version 2.0
Output:
Bluetooth Standard Power Class 2 (Max. +4 dBm)
Maximum communication range:
Line of sight approx. 10 m (33 ft)*1
Frequency band:
2.4 GHz band (2.4000 2.4835 GHz)
Modulation method: FHSS
Compatible Bluetooth Profiles*2:
A2DP (Advanced Audio Distribution Profile)
AVRCP (Audio Video Remote Control Profile)
HFP (Handsfree Profile) 1.5
HSP (Headset Profile)
General
Outputs:
Audio outputs terminal (front/rear)
Subwoofer output terminal (mono)
Power antenna (aerial) relay control terminal
Power amplifier control terminal
Inputs:
BUS control input terminal
BUS audio input terminal
Telephone ATT control terminal
Remote controller input terminal
Antenna (aerial) input terminal
MIC input terminal
AUX input jack (stereo mini jack)
USB signal input connector
Tone controls:
Low: 10 dB at 60 Hz (XPLOD)
Mid: 10 dB at 1 kHz (XPLOD)
High: 10 dB at 10 kHz (XPLOD)
Power requirements: 12 V DC car battery
(negative ground (earth))
Dimensions: Approx. 178 u 50 u 179 mm
(7 1/8 u 2 u 7 1/8 in) (w/h/d)
Mounting dimensions: Approx. 182 u 53 u 162 mm
(7 1/4 u 2 1/8 u 6 1/2 in) (w/h/d)
Mass: Approx. 1.2 kg (2 lb 11 oz)
Supplied accessories:
Card remote commander: RM-X304
Parts for installation and connections (1 set)
Design and specifications are subject to change
without notice.
AUDIO SYSTEM
9-889-696-01
Sony Corporation
2009K0500-1
2009.11
MEX-BT38UW/BT3800U/BT3807U/BT3850U
MEX-BT38UW/BT3800U/BT3807U/BT3850U
TABLE OF CONTENTS
1.
2.
GENERAL ...................................................................
3.
DISASSEMBLY
3-1.
3-2.
3-3.
3-4.
3-5.
3-6.
3-7.
3-8.
3-9.
3-10.
3-11.
3-12.
3-13.
4.
DIAGRAMS
5.
13
13
14
14
15
15
16
16
17
17
18
19
19
21
22
23
25
26
27
28
29
30
31
32
EXPLODED VIEWS
6.
MEX-BT38UW/BT3800U/BT3807U/BT3850U
SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
Never look into the laser diode emission from right above when
checking it for adjustment. It is feared that you will lose your sight.
If the optical pick-up block is defective, please replace the whole
optical pick-up block.
Never turn the semi-fixed resistor located at the side of optical
pick-up block.
optical pick-up
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
Unleaded solder melts at a temperature about 40 C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
TEST DISCS
Use following TEST DISC when this set confirms the operation
and checks it.
Part No.
Description
3-702-101-01
4-225-203-01
MAIN board
(CN350)
extension cable
(Part No. J-2502-076-1)
SERVO board
(CN401)
MEX-BT38UW/BT3800U/BT3807U/BT3850U
MODEL IDENTIFICATION
Bottom View
Part No.
Part No.
Destination
4-160-362-0[]
4-160-363-0[]
BT38UW
4-160-364-0[]
4-160-365-0[]
BT3807U
4-160-366-0[]
BT3850U: E model
4-160-367-0[]
USB connector
front panel
1
Notes on the lithium battery
Keep the lithium battery out of the reach of children.
Should the battery be swallowed, immediately consult a doctor.
Wipe the battery with a dry cloth to assure a good
contact.
Be sure to observe the correct polarity when
installing the battery.
Do not hold the battery with metallic tweezers,
otherwise a short-circuit may occur.
WARNING
Battery may explode if mistreated.
Do not recharge, disassemble, or dispose of
in fire.
MEX-BT38UW/BT3800U/BT3807U/BT3850U
5. Precautions
Beware of the following points when conducting the
talking test:
There is no fault if a talking can be made by adjusting appropriately the volume of the telephone of the other party and the
cellular phone connected through the Bluetooth, besides the
setup of MEX-BT38UW/BT3800U/BT3807U/BT3850U.
The speakers voice will become loud naturally if the periphery is noisy, or become low if quiet. (even though the speaker
intents to talk on the same volume level)
The speakers voice will become loud naturally if the other
partys voice is loud.
Note: The functions that can be operated vary depending on the BT audio
device connected.
8. Initialize
This should be performed when the set is sent back to the user after
all the checks finished successfully.
1. Execute the initialization.
2. Press the [BLUETOOTH] button for 3 seconds to check if the
BT logo lights up.
3. Check that the set is not connected automatically to the cellular
phone that was connected last.
4. With the BT audio source, check that the streaming logo does
not blink when the [6] button is pressed.
4. Perform ACC OFF ON to check if the set can be reconnected to the BT audio device. (Some BT audio devices may
be reconnected automatically)
5. With the BT audio source, press the [6] button to check if the
streaming logo blinks and the set is reconnected to the BT audio device. (This function is disabled while the set is reconnected to a cellular phone. Accordingly, this test should be
conducted after the power is turned on and then the HF logo
lights up, or when about 30 seconds elapsed after the power
on)
MEX-BT38UW/BT3800U/BT3807U/BT3850U
SECTION 2
This section is extracted
from instruction manual.
GENERAL
(BT38UW/BT3800U: US and Canadian models)
3OURCE SELECTOR
NOT SUPPLIED
3LECTEUR DE SOURCE
NON FOURNI
3UPPLIED WITH THE #$ CHANGER
&OURNI AVEC LE CHANGEUR DE #$
8! #
FROM CAR ANTENNA AERIAL