Vous êtes sur la page 1sur 4

SUBJECT:

NO. REV. PAGE

ASS-20-80-0475-04 A 1 of 4

4-3/4" GT AUTOTRAK STEERABLE STABILIZER ASSEMBLY FISHING DIMENSIONS


REV A DCR # -- / IK AMENDMENT DETAIL Initial Release

APPROVAL J. Coogan

DATE 2008-09-20

OPERATING INSTRUCTION
This fishing dimensions document for the 4-3/4" GT AutoTrak Steerable Stabilizer Assembly has been designed in order to provide information regarding tool ODs, IDs and length in case a fishing operation is required on the corresponding components. The 4-3/4" V1 AutoTrak Steerable Stabilizer Assembly is designed and available in five different hole sizes 5-3/4", 5-7/8", 6", 6-1/ 8", 6-1/2" and 6-3/4". Hole Size adjustment are done by the assembly of different ribs. All other components are common for all hole sizes. The document for the 4-3/4" GT AutoTrak Steerable Stabilizer Assembly is separated into three sections 1) The outer parts and dimensions are shown on page 2. 2) The inner parts and dimensions are shown on page 3. 3) The Rig Measure Record on page 4 to document actual measurements. The sub dimensions on page 2 and 3 are listed in two tables - one with US-units and one with SI-units. The explanation of each column is as follows: "Cross Section" : "OD" : "ID" : "Fishing Length" : Defines sections where a fishing tool could be placed on Outer Diameter of the corresponding cross section Inner Diameter of the corresponding cross section Maximum cylindrical fishing length

Note: All mentioned dimensions belong to newly manufactured 4-3/4" GT AutoTrak Steerable Stabilizer Assembly. Wear and standard rework procedures, based on BHI inspection / repair criteria can result in a slight change in these dimensions. Thus, it is important that the INTEQ FSE on location measures and document the actual sub dimensions on the Rig Measure Record before the tool is run in hole. Please contact the BOT representatives in your region, if it becomes necessary to fish a 4-3/4" GT AutoTrak Steerable Stabilizer Assembly. The BOT representative will select the correct fishing tool based on the information recorded on the Rig Measure Record, before the sub was run into the hole.
Restriction Note:

The tool/sub dimensions mentioned in this document are distributed to the customer of Baker Hughes INTEQ for fishing purposes only. It is not permitted to further distribute this data to other companies except to the fishing service provider instructed by the customer to plan or perform a required fishing operation/service on these INTEQ tools. The data/dimensions are also not to be used by the customer or by a third party company to perform any calculation or simulation on the BHA behavior, including bending moment distribution or dynamic analysis.
Uncontrolled when printed

SUBJECT:

NO. REV. PAGE

ASS-20-80-0475-04 A 2 of 4

4-3/4" GT AUTOTRAK STEERABLE STABILIZER ASSEMBLY FISHING DIMENSIONS

US Dimensions Outer Parts


Cross Section 1 2 3 OD [inch] 5.024 5.236 5.236 Fishing Length [inch] 45.118 69.181 15.876

SI Dimensions Outer Parts


Cross Section 1 2 3 OD [mm] 127,60 133,00 133,00 Fishing Length [mm] 1146,00 1757,20 403,25

* Retracted Rib OD
Size 5-3/4" 5-7/8" 6" 6-1/8" 6-1/2" 6-3/4 [mm] 139,84 139,84 142,90 145,96 155,60 161,96 [inch] 5.506 5.506 5.626 5.746 6.126 6.376

Uncontrolled when printed

SUBJECT:

NO. REV. PAGE

ASS-20-80-0475-04 A 3 of 4

4-3/4" GT AUTOTRAK STEERABLE STABILIZER ASSEMBLY FISHING DIMENSIONS

US Dimensions Inner Parts


Cross Section 4 5 ID [inch] 3.096 1.000 Fishing Length [inch]

SI Dimensions Inner Parts


Cross Section 4 5 ID [mm] 78,65 25,40 Fishing Length [mm]

Uncontrolled when printed

SUBJECT:

NO. REV. PAGE

ASS-20-80-0475-04 A 4 of 4

4-3/4" GT AUTOTRAK STEERABLE STABILIZER ASSEMBLY FISHING DIMENSIONS

Rig - Measure Record

Uncontrolled when printed

Vous aimerez peut-être aussi