Académique Documents
Professionnel Documents
Culture Documents
ARP3111
PLASMA DISPLAY
PDP-433PE
PDP-433PU
Type
WYVI6 KUC
PDP-433PU
? AC220 - 240V AC120V
Power Requirement
Remarks
This Service Manual should be used together with the following manual(s).
Model No.
PDP-433PE PDP-433PU
Order No.
ARP3112
Remarks
SCHEMATIC DIAGRAM and PCB DIAGRAM
System
PDP-4330HD PDP-R03U PDP-433PU
Service Manual
PDP-R03E : ARP3110 PDP-R03U : ARP3113 ARP3111 ARP3112
Remaks
PIONEER CORPORATION
4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PDP-433PE, PDP-433PU
SAFETY INFORMATION
This service manual is intended for qualified service technicians ; it is not meant for the casual do-ityourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a qualified service technician.
WARNING This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to cause cancer, birth defects or other reproductive harm. Health & Safety Code Section 25249.6 Proposition 65
NOTICE (FOR CANADIAN MODEL ONLY) Fuse symbols (fast operating fuse) and/or be of identical designation.
REMARQUE (POUR MODLE CANADIEN SEULEMENT) Les symboles de fusible (fusible de type rapide) et/ou de remplacement doivent avoir la mme dsignation.
SAFETY PRECAUTIONS
NOTICE :Comply with all cautions and safety related notes located on or inside the cabinet and on the chassis. The following precautions should be observed : 1. When service is required, even though the PDP UNIT an isolation transformer should be inserted between the power line and the set in safety before any service is performed. 2. When replacing a chassis in the set, all the protective devices must be put back in place, such as barriers, nonmetallic knobs, adjustment and compartment covershields, isolation resistorcapacitor, etc. 3. When service is required, observe the original lead dress. Extra precaution should be taken to assure correct lead dress in the high voltage circuitry area. 4. Always use the manufacture's replacement components. Especially critical components as indicated on the circuit diagram should not be replaced by other manufacture's. Furthermore where a short circuit has occurred, replace those components that indicate evidence of overheating. 5. Before returning a serviced set to the customer, the service technician must thoroughly test the unit to be certain that it is completely safe to operate without danger of electrical shock, and be sure that no protective device built into the set by the manufacture has become defective, or inadvertently defeated during servicing. Therefore, the following checks should be performed for the continued protection of the customer and service technician. 6. Perform the following precautions against unwanted radiation and rise in internal temperature. Always return the internal wiring to the original styling. Attach parts (Gascket, Ferrite Core, Ground, Rear Cover, Shield Case etc.) surely after disassembly. 7. Perform the following precautions for the PDP panel. When the front case is removed, make sure nothing hits the panel face, panel corner, and panel edge (so that the glass does not break). Make sure that the panel vent does not break. (Check that the cover is attached.) Handle the FPC connected to the panel carefully. Twisting or pulling the FPC when connecting it to the connector will cause it to peel off from the panel. 8. Pay attention to the following. When the front case is removed, infrared ray is radiated and may disturb reception of the remote control unit. Pay extreme caution when the front case and rear panel are removed because this may cause a high risk of disturbance to TVs and radios in the surrounding.
PDP-433PE, PDP-433PU
Also test with plug reversed (Using AC adapter plug as required) Earth ground
AC Leakage Test
ANY MEASUREMENTS NOT WITHIN THE LIMITS OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL SHOCK HAZARD AND MUST BE CORRECTED BEFORE RETURNING THE SET TO THE CUSTOMER.
PDP-433PE, PDP-433PU
1. AC Power Cord 2. AC Inlet with Filter 3. Power Switch (S1) 4. Fuse (In the SW POWER SUPPLY Module) 5. STB Transformer and Converter Transformer (In the SW POWER SUPPLY Module) 6. Other primary side of the SW POWER SUPPLY Module
Y DRIVE Assy
: Part is Charged Section. : Part is the High Voltage Generating Points other than the Charged Section.
Top Front
SCAN (B) Assy
X CONNECTOR (B) Assy SW POWER SUPPLY Module AC Inlet with Filter Power Switch (S1)
Power Cord
Fig.1 Charged Section and High Voltage Generating Point (Rear View)
PDP-433PE, PDP-433PU
1. Product safety
You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and should keep the safety during servicing by following the safety instructions described in this manual.
2. Adjustments
To keep the original performances of the product, optimum adjustments or specification confirmation is indispensable. In accordance with the procedures or instructions described in this manual, adjustments should be performed.
3. Cleaning
For optical pickups, tape-deck heads, lenses and mirrors used in projection monitors, and other parts requiring cleaning, proper cleaning should be performed to restore their performances.
PDP-433PE, PDP-433PU
CONTENTS
1. SPECIFICATIONS ................................................. 7 2. EXPLODED VIEWS AND PARTS LIST ................. 8 3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM ... 30 (For SCHEMATIC DIAGRAM, refer to ARP3112) 4. PCB CONNECTION DIAGRAM ... Refer to ARP3112 5. PCB PARTS LIST ................................................ 46 6. ADJUSTMENT ..................................................... 57 7. GENERAL INFORMATION ................................ 77 7.1 DIAGNOSIS .................................................. 77 7.1.1 PCB LOCATION ................................... 77 7.1.2 SHUT DOWN/POWER DOWN DIAGNOSIS BY LED DISPLAY ........... 78 7.1.3 DISASSEMBLY ..................................... 85 7.2 IC INFORMATION ........................................ 89 8. PANEL FACILITIES .......................................... 108
PDP-433PE, PDP-433PU
1. SPECIFICATIONS
Item Number of Pixels Audio Amplifier Power Requirement Dimensions Weight Accessories Model: PDP-433PE 1024 768 pixels 12 W + 12 W (1kHz, 10%, 8) AC 220240 V, 50/60 Hz, 320 W (0.6 W Standby) AC 120 V, 60 Hz, 318 W (0.6 W Standby) 1070 (W) 630 (H) 98 (D) mm [421/8 (W) 2413/16 (H) 37/8 (D) inch] 31.5 kg (69.4 lbs) Power Cord, Cleaning Cloth, Three speed clamps, Three bead bands, Warranty card Model: PDP-433PU
Accessories
Power cord (ADG1173) (ADG1193) (ADG1178)
Warranty card
PDP-433PE, PDP-433PU
Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List. The mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. Screws adjacent to mark on the product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual.
(In the case of no amount instructions, apply as you think it appropriate.)
2.1 PACKING
(1) PACKING PARTS LIST
Mark No.
1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Packing Case (43) Carton (43) Pad (43U) Mirror Mat Warranty Card See Contrast table (2) AHD3100 AHA2282 AHG1284 See Contrast table (2)
Description
Part No.
NSP
Polyethylene Sheet AHG1302 Pad (43L) AHA2283 Cord Case AHC1037 Binder Assy AEC1908 (Speed Clamp 3, Bead Band 3) Wiping Cloth Power Cord Power Cord Power Cord Vinyl Bag Caution Sheet AED1197 See Contrast table (2) See Contrast table (2) See Contrast table (2) AHG1310 ARM1201
13 8 7
15
2 Front
NSP
PDP-433PE, PDP-433PU
9 Upper side
3 2 5 6 7
2 or 3
Description
Part No.
Mark No.
5 6 7 8 9
Description
Circuit Board Spacer PCB Spacer Circuit Board Spacer Screw Screw
Part No.
AEC1872 AEC1253 AEC1873 VBB30P100FNI ABA1301
ADR RESONANCE Assy AWZ6682 BRIDGE C Assy AWZ6676 BRIDGE D Assy AWZ6677 Panel Chassis (43) Assy AWU1038 [Refer to "2.14 PANEL CHASSIS (43) ASSY".]
PDP-433PE, PDP-433PU
Description
CLAMP A Assy CLAMP B Assy Wire Saddle Locking Card Spacer Screw
Part No.
AWZ6668 AWZ6669 AEC1904 AEC1736 ABA1301
10
PDP-433PE, PDP-433PU
13 13 3 4 4
6 11 12 11 Upper side
14 9
14
Description
DIGITAL VIDEO Assy X DRIVE Assy Insulation Sheet Metal Fitting Heat Sink Silicone Sheet Drive Heatsink Assy Drive Silicone Sheet Coil Silicone Sheet Circuit Board Spacer Screw Screw Screw
Part No.
AWV1929 AWV1930 AMR3263 ANG2464 ANH1594 AEH1039 15 ANH1598 AEH1041 AEH1048 AEC1872 ABZ30P060FMC VBB30P100FNI PMB30P060FNI
10
14
10
Upper side
11
2 Upper side
4 8
Upper side
12
PDP-433PE, PDP-433PU
Description
Y DRIVE Assy Circuit Board Spacer Drive Heatsink Assy Drive Silicone Sheet Scan IC Spring (43L) Scan IC Spring (43R) Scan Insulation Sheet (43) Screw Screw
Part No.
AWZ6683 AEC1872 ANH1598 AEH1041 ABK1029 ABK1030 AMR3287 VBB30P100FNI PMB30P060FNI
13
PDP-433PE, PDP-433PU
1 or 2
17
10
18
13
18 11 12
11 18
12 13
Upper side 2 13 7 14 15 1
16
16
17
17
19
17
14
PDP-433PE, PDP-433PU
Description
BRIDGE A Assy BRIDGE B Assy THERMAL SENSOR Assy ADR RESONANCE Assy CLAMP A Assy CLAMP B Assy Heat Sink Silicone Sheet FFC Holder Rivet
Part No.
AWZ6674 AWZ6675 AWZ6660 AWZ6682 AWZ6668 AWZ6669 ANH1594 AEH1039 AMR3302 BEC1066
Mark No.
11 12 13 14 15 16 17 18 19
Description
Insulation Sheet Metal Fitting Wire Saddle PCB Spacer Circuit Board Spacer Locking Card Spacer Screw Screw Screw
Part No.
AMR3263 ANG2464 AEC1904 AEC1253 AEC1873 AEC1736 ABA1301 ABZ30P060FMC VBB30P100FNI
15
PDP-433PE, PDP-433PU
Upper side
39 1 White 27 29 Tape
27 30 2
10
16
K3
27 5 3
31 27 32
27
43
SA1 SA2
17 12 35
D8
36
TE1 D16 D9 D10
37
D1 D18 D6 Y1 Y2 D11
34 20
X2 X1
33
41
D7
28
D15 D14
38 18 19
13 15 14
D12 D13
D2 D3 D17
25 26 42 40
SA2 SA1 K3
27
27
24
27
27
23
27
11
22 2
21
White Tape
39
16
PDP-433PE, PDP-433PU
Description
ADR CONNECT A Assy ADR CONNECT B Assy ADR CONNECT C Assy ADR CONNECT D Assy ADR RESONANCE Assy BRIDGE A Assy BRIDGE B Assy BRIDGE C Assy BRIDGE D Assy SUB ADDRESS A Assy SUB ADDRESS B Assy SCAN (A) Assy SCAN (B) Assy Y DRIVE Assy DIGITAL VIDEO Assy THERMAL SENSOR Assy X CONNECTOR (A) Assy X CONNECTOR (B) Assy X DRIVE Assy J204 Flexible Flat Cable J209 J210 J211 J212 J201 Flexible Flat Cable Flexible Flat Cable Flexible Flat Cable Flexible Flat Cable Flexible Flat Cable
Part No.
AWZ6678 AWZ6679 AWZ6680 AWZ6681 AWZ6682 AWZ6674 AWZ6675 AWZ6676 AWZ6677 AWZ6692 AWZ6693 AWZ6666 AWZ6667 AWZ6683 AWV1929 AWZ6660 AWZ6672 AWZ6673 AWV1930 ADD1207 ADD1206 ADD1204 ADD1199 ADD1201 ADD1194
Mark No.
26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43
Description
J202 Flexible Flat Cable Flat Clamp J203 Flexible Flat Cable J205 Flexible Flat Cable J206 Flexible Flat Cable J207 Flexible Flat Cable J208 Flexible Flat Cable Power Sheet (43) Rivet J110 3P Housing Wire J108 8P Housing Wire J102 Wire PE J103 13P Housing Wire J116,J117 4P Housing Wire J120 Wire L J101 13P Housing Wire J109 8P Housing Wire Nylon Binder
Part No.
ADD1194 AEC1879 ADD1198 ADD1202 ADD1200 ADD1208 ADD1205 AMR3284 BEC1066 ADX2741 ADX2740 ADX2738 ADX2766 ADX2767 ADX2763 ADX2768 ADX2743 AEC-093
NSP NSP
NSP NSP
17
PDP-433PE, PDP-433PU
10
10 11
Upper side
11
1 2
11
Upper side
10
11
12 7 12 2 11 Upper side 11
Upper side
11
11
11
8 11
14 14
13
18
PDP-433PE, PDP-433PU
Description
Front Chassis HU (43) Card Spacer Niplocker Card Corner Holder Sub Frame L Sub Frame R Front Chassis HL (43) Front Chassis V (43) FPC Cushion (43) Screw Screw Screw VR Cushion V Cushion
Part No.
ANA1670 AEC1902 AEC1803 BEC1144 ANG2483 ANG2484 ANA1671 ANA1672 AEB1371 ABA1283 ABA1294 BMZ30P060FMC AEB1374 AED1205
19
29
29
16 14 5 6
8 28
12 27 7 8 11 15 9 8
10
13
Upper side
19
30
20 23 25
24
21
26
22 3 30 32 22 4 18 30 31
32
20
PDP-433PE, PDP-433PU
Description
AUDIO AMP Assy FRONT KEY CONN Assy IR (P) Assy LED Assy Nylon Rivet IF Sheet Edge Saddle Wire Saddle IF Shield L2 Toroidal Core J214 3P Housing Wire S2 Power Switch Niplocker PCB Spacer J215 3P Housing Wire
Part No.
AWZ6687 AWZ6657 AWZ6658 AWZ6655 AEP-211 AMR3298 AEC1571 AEC1745 ANA1675 ATX1042 ADX2735 ASG1089 BEC1136 AEC1570 ADX2757
Mark No.
16 17 18 19 20 NSP 21 22 23 24 25 26 27 28 29 30 31 32
Description
Spacer Audio Base Screw V Cushion J113 Wire PJ IR Holder Nylon Rivet S1 Power Switch J106 Wire PC J104 3P Housing Wire Switch Holder Screw Screw Screw Screw Gascket R Screw
Part No.
AEC1360 ANA1687 BMZ30P060FZK AED1205 ADX2742 ANG2494 AEC1671 ASG1082 ADY2745 ADX2748 ANG2493 ABA1294 PMB30P060FNI AMZ30P060FZK BMZ30P040FMC ANK1695 ABZ30P050FZK
NSP
21
PDP-433PE, PDP-433PU
1 5
4 14 J201 17 12 J202 6 7 15 16 14
10
11
Note 1: When there is not S4004, set only S4001. Note 2: When there are not S4001 and S4004, setting is unnecessary.
22
PDP-433PE, PDP-433PU
Description
MR INTERFACE Assy Terminal Panel (HD) L6 Ferrite Core J201 Flexible Flat Cable J118 Wire P J111 14P Housing Wire L3 Toroidal Core J214 3P Housing Wire J104 3P Housing Wire Ferrite Core Holder J113 Wire PJ J202 Flexible Flat Cable Screw Screw Screw Screw Screw
Part No.
AWZ6654 ANG2485 ATX1037 ADD1194 ADX2765 ADX2730 ATX1042 ADX2735 ADX2748 AEC1818 ADX2742 ADD1194 TBZ40P080FZK AMZ30P060FZK BBA1051 PMZ26P030FZK ABA1294
23
PDP-433PE, PDP-433PU
18
16
11
10
13
12
P7 P6 P1 P2 P3 P5 P4
24
PDP-433PE, PDP-433PU
Description
SW Power Supply Module FU1 Fuse (10A) IF Earth Metal Silicone Sheet P L1 Ferrite Core CN1 AC Inlet with Filter J105 Wire PB J114 Earth Wire SP TERMINAL Assy J101 13P Housing Wire J118 Wire P J103 13P Housing Wire J102 Wire PE Screw Screw Screw Solder Warning Label Screw
Part No.
AXY1056 See Contrast table (2) ANA1690 AEH1035 ATX1032 AKP1223 ADX2744 ADX2709 AWZ6688 ADX2768 ADX2765 ADX2766 ADX2738 PMB30P060FNI AMZ30P060FZK BPZ30P080FZK See Contrast table (2) BMZ30P060FZK
25
PDP-433PE, PDP-433PU
Description
FRONT KEY Assy Front Case Assy 43 (P) Rivet L5 Ferrite Core Lead Cover (P) Pioneer Badge Panel Holder (43) Spacer Panel Cushion V (43) Panel Cushion H (43) Protect Panel Assy (43) Screw Screw Serial Sheet J213 Flexible Flat Cable Flexible Seal (P) Power Button Coil Spring Energy Star Label HDTV Label
Part No.
AWZ6656 AMB2725 AEC1877 ATX1043 AMB2704 AAM1091 ANG2487 AEC1896 AED1201 AED1200 AMR3303 ABZ30P050FZK VMZ30P060FZK AAX2609 ADD1193 AEH1052 AAD4113 ABH1108 See Contrast table (2) See Contrast table (2)
19 18
14 13 17
Foil Side
6 7 8 9 10 11 12 13 14 15
16 12 7 12 7
NSP
16 17 18 19 20 21
12
12
8 12
12 10
9 9
10
11
26
Part No.
ANE1600 ANK1694 AMZ30P060FZK TBZ40P080FZK AAX2751 See Contrast table (2) AAX2852 AAX2858 See Contrast table (2)
1 2 3 4 5 NSP 6 7 8 9
3 9
3 1
Bottom View 2
27
PDP-433PE, PDP-433PU
PARTS LIST
Mark No.
NSP NSP NSP NSP NSP NSP NSP
Description
Panel Chassis (43) Assy Front Chassis V (43) Front CHassis HU (43) Front Chassis HL Sub Frame L (43) Sub Frame R (43) Scan IC Spring (43L) Scan IC Spring (43R) Metal Fitting FPC Cushion (43) PCB Spacer Locking Card Spacer Circuit Board Spacer Circuit Board Spacer Spacer Card Spacer Wire Saddle Panel Cushion H (43) Panel Cushion V (43) V Cushion
Part No.
AWU1038 ANA1672 ANA1670 ANA1692 ANG2483 ANG2484 ABK1029 ABK1030 ANG2464 AEB1371 AEC1211 AEC1736 AEC1872 AEC1873 AEC1896 AEC1902 AEC1904 AED1200 AED1201 AED1205
Mark No.
Description
Insullation Sheet Scan Sheet (43) Card Corner Holder Screw Screw Screw Screw Screw Screw Bolt Corner Pad Upper Carton Under Carton Packing Sheet Washer VR Cushion Niplocker Static Plate Plate Screw Washer
Part No.
AMR3263 AMR3287 BEC1144 ABA1283 ABA1294 ABZ30P060FMC BMZ30P060FMC PMB30P060FNI VBB30P100FNI ABA1259 AHA2293 AHD3139 AHD3140 AHG1291 WB80FZB AEB1374 AEC1803 AHK1013 AHK1014 BYC40P220FMC WC60FZK
NSP
PARTS LIST
Mark No.
NSP NSP NSP NSP NSP NSP NSP NSP NSP NSP NSP NSP
LIST OF ASSY
Part No.
AWV1927 AWV1928 AXF1110 ADY1079 ADY1080 ANA1693 ANA1668 ANA1669 ANH1601 ANG2457 ANG2458 AMR3262 AEH1043 AEH1044 AEH1054 AEH1055 AEH1056 AEC1015 AEC1889 AEH1047 AAV1239 VBB30P100FNI
Description
SCAN FUKUGO ASSY ADDRESS FUKUGO ASSY Address Module (IC1 - IC32) FPC (J1,J2) FPC (J3,J4) Chassis Assy (43) Chassis (43) Base Chassis (43) Scan Heatsink (43) Corner Angle A Corner Angle B Tube Cover Silicone Sheet 43 Adhesive Tape 43 Adhesive Tape B 43 Panel Silicone Sheet Silicone Sheet B 43 Pin Grommet Card Spacer Scan Silicone Sheet (43) Plasma Panel Assy (43) Screw
Mark No.
NSP NSP NSP NSP NSP NSP NSP NSP NSP NSP NSP NSP NSP NSP NSP
Description
Part No.
AWV1927 AWZ6666 AWZ6667 AWZ6672 AWZ6673 AWZ6674 AWZ6675 AWZ6676 AWZ6677 AWV1928 AWZ6668 AWZ6669 AWZ6678 AWZ6679 AWZ6680 AWZ6681 AWZ6682
SCAN FUKUGO ASSY SCAN (A) ASSY SCAN (B) ASSY X CONNECTOR (A) ASSY X CONNECTOR (B) ASSY BRIDGE A ASSY BRIDGE B ASSY BRIDGE C ASSY BRIDGE D ASSY ADDRESS FUKUGO ASSY CLAMP A Assy CLAMP B Assy ADR CONNECT A ASSY ADR CONNECT B ASSY ADR CONNECT C ASSY ADR CONNECT D ASSY ADR RESONANCE ASSY
NSP
28
PDP-433PE, PDP-433PU
29
PDP-433PE, PDP-433PU
VADR2 CLAMP
CLK/LE
IC6501 Buffer IC
VADR2
VADR2
CLAMP
CLK/LE
IC6601 Buffer IC
VADR2
CLA1
BGA1
CLAMP A ASSY
BRIDGE A ASSY
K2
K1 SAA3
+60 ADR_CO
SAA2
D8
D9
D16
D1
+12V V+5V +12V DC/DC Conv. Module +12V V+3V V+2V
D10
V+5V_STB
TE1
D11
V+3V
D7 D18 Y1
IC1703 XY Drive Sequence Pattern Gen. XDRV_SIG ADL_LE_UL ADL_LE_DL
Y4
PSUS Y-SUS MASK Block
+5V +15V VSUS IC2206 Pulse Module +15V VSUS Drive Signal
YDRV_SIG SCAN_SIG
D4
D6 Y2
+Reset Block VCC_VH V_IC5V VCP +5V +15V VSUS Y-SUS MASK Block IC2204 Pulse Module Drive Signal
Logic Block
D15
Y3
V+3V_I V+2V_I +15V Soft-D Block IC1401 (IC31 R) Sub-Field Conv. for Right with Field Memory
D14
IC5 VCC_VH IC6002 ADD SEL_PULSE IC5 VCC_VH IC6003 ADD SEL_PULSE IC5 VCC_VH IC6004 ADD SEL_PULSE IC5 VCC_VH IC6005 ADD SEL_PULSE IC5 VCC_VH IC6006 ADD SEL_PULSE PSUS
Y5
VC_VF+ VC_VF- V_OFS
D2
ADCLK_DR V+3V Scan Signal Offset Block V+5V_STB IC119 Flash ROM V+3V IC120 Module UCOM TXD/RX IC1101 Panel UCOM RA2:9 RB2:9 TXD0/RX0 RE LED_SIG I2 BA2:9 BB2:9 GA2:9 GB2:9
Y6
D3
SW21
KL21
KL22
IR (P) ASSY
SAB2
D
CLAMP B ASSY
CLB1
CLAMP VADR2
ADR_CO
RE1
BRIDGE C ASSY
BGC1 AD1
CLAMP CLK/LE IC6901 Buffer IC
SAB3 K1
Q6706 - Q6711 VADR Gen.
VADR2
VADR2
AC1
CLK/LE IC6801 Buffer IC VADR2
30
1
Driver IC
Driver IC
Driver IC
Driver IC
Driver IC
Driver IC
Driver IC
Driver IC
Driver IC
Driver IC
Driver IC
Driver IC
Driver IC
Driver IC
Driver IC
Driver IC
PDP433PE, PDP-433PU
Note : When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or "PCB PARTS LIST".
A
Driver IC Driver IC Driver IC Driver IC Driver IC Driver IC Driver IC Driver IC Driver IC Driver IC Driver IC Driver IC Driver IC Driver IC Driver IC Driver IC
VADR2
CLK/LE
IC6801 Buffer IC
VADR2
VADR2
CLAMP
CLK/LE
IC6901 Buffer IC
VADR2 CLAMP
BGB1
CLB1
K3
BRIDGE B ASSY
CLAMP B ASSY
T104
T105
PRIMARY SECONDARY
+13.5V
VADR
+13.5V
VSUS
VSUS
+12V
+15V
+15V
+6.5V
LIVE NEUTRAL
-9V
-9V
AC IN X DRIVE ASSY
X1
+5V DC/DC Conv. Block VSUS +15V VCP
P1
P2
P5
P6
P3
P4
X3
Drive Signal
X_SUS MASK
P_SUS
R23
+5V L R L R IC5202 Volume & Tone & Balance Logic Block +12V IC5201 FOCUS SRS SRS & Focus +Reset Pulse Block +12V V_RN +15V
MR INTERFACE ASSY
Scalling Gamma
L, R
R3
TMDS Receiver
A24 R27
L, R
X2
+15V
P7
STB5V STB5V STB5V
VM1
C
P_SUS
IC5002 I2C_BUS (SCL/SDA) V+5V_DIG KEY1 KEY2 LED_SIG TXD/RXD SR_UP IC4011 I/O Expander Power Amp. Drive Signal IC3201 Pulse Module X_SUS MASK
R24
A21
+13.5V +12V IC5001 Reg.
X4
A22
TMDS with HDCP AUDIO_SIG (L/R)
R11
L1
SR_DW
V+5V_ST V+5V_ST
R22
SP TERMINAL ASSY
SP21
SP OUT
L, R
D
K3
BRIDGE D ASSY
BGD1 AB1
CLAMP CLK/LE IC6601 Buffer IC
CLAMP A ASSY
CLA1 AA1
CLAMP CLK/LE IC6501 Buffer IC VADR2
VADR2
VADR2
VADR2
Driver IC
Driver IC
Driver IC
Driver IC
Driver IC
Driver IC
Driver IC
Driver IC
Driver IC
Driver IC
Driver IC
Driver IC
Driver IC
Driver IC
Driver IC
Driver IC
31
8
PDP-433PE, PDP-433PU
TMDS
IC4203 (CONF_ROM) Q4201, Q4202 (5V 3.3V I2C_LEVEL_SHIFT) IC4201 (DDC_ROM) Q4005, Q4006 (5V 3.3V I2C_LEVEL_SHIFT) IC4012 (IC2_SW) DDC_SCL DDC_SDA
B
Q4018 (INV) C4043 (HPF)
IC4006 (REM_SLICER)
15 SR_UP
V+5V_DIG
Q4008 (2.5V_REG)
IC4005 (I/O_EXPANDER)
A_SCL A_SDA
11 M_TXD
IC4006 (BUFF)
1 M_RXD
TXD0
Q4012 (INV)
REM
14 SR_DOWN
IC4008, IC4009 (REM_SW) Q4007 (BUFF)
5 SM_POW
IC4010 (BUFF)
SM_POW
7 CCKM
CCKM
8 CSEN2
10 20 SPL
L_CH
Q4402 (BUFF)
4 13 SPR
R_CH
D
LED_G LED_R KEY1 KEY2 REM
CN4401
CN4007
CN4009
32
1 2 3 4
CN4004, CN4005
CN4002 (MDR)
PDP-433PE, PDP-433PU
Voltages
CN4002 (MDR Connector) ( Media Receiver)
No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Name M_RXD GND SENCE SPR SMPOW GND CCKM CSEN2 CSEN1 SPL M_TXD GND SPR SR_DW SR_UP Description 232C bus (PDP MR) Connecting detection for MR Audio signal R ch MR relay control System activation detection System activation signal Not used Audio signal L ch 232C bus (MR PDP) Voltage at INPUT4 NTSC Input 0-5V swing square wave 0.0V DC Analog audio signal wave 3.5V DC 1.9V DC 5.0V DC Analog audio signal wave 0-3.3V swing square wave
I2C for DDC I2C for DDC DVI signal DVI signal
0-5V swing square wave 0-5V swing square wave DVI signal DVI signal
Audio signal R ch Analog audio signal wave Remote control signal 5.0V DC MDR connecting detection signal 3.75V DC multiplex remote control signal
I2C power supply for DDC HOT_PLUG detection DVI signal DVI signal
GND FRASH_W Not used SRST Not used GND SPL Audio signal L ch
8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal
0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave
8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal Clock Data enable Horizontal sync. signal Vertical sync. signal I2C bus Front key signal 1 MDR connecttion Detect signal MR relay control Audio mute System activation detect SiI861 I2C bus master infomation Not used Not used System activation signal Front key signal 2 I2C bus Green LED control signal 232C bus Red LED control signal 232C bus I2C for DDC Remote control signal I2C for DDC
0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave (40MHz) 0-3.3V swing square wave (+ polarity) 0-3.3V swing square wave (- polarity 48.4kHz) 0-3.3V swing square wave (- polarity 60.0Hz) 0-5V swing square wave 5.0V DC 3.75V DC 5.0V DC 0.0V DC 1.9V DC 0.0V DC
8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal 8 bit video signal
0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave 0-3.3V swing square wave
5.0V DC 5.0V DC 0-5V swing square wave 0.0V DC 0-5V swing square wave 5.0V DC 0-5V swing square wave 0-5V swing square wave 5.0V DC 0-5V swing square wave
33
PDP-433PE, PDP-433PU
MR INTERFACE ASSY
RGB 2 phase 8 bit
3.3V 2.5V
Address Data
IC4204 SiI861
VD HD DE CLK Address BUS Data BUS 3.3V Control Signal Reflesh-rate Det.
Address Data
VD 31
APLR
AND
RESET
ADR_K_EMG 5V
Reset IC CN1201
EXT_RXD EXT_TXD
DEW DET
RST PU
5.0V 3.3V
EXD RXD EXD TXD
3.3V 5.0V
RST2
AND
ADR PD
STB5V
STB5V
IIC BUS
EEP ROM
DCC_PD 5V
RESET
TEMP1
DIG. ADR. PD
Reset IC
AC_OFF PD_TRIGGER
34
1 2 3 4
STB5V
12V
K3105 SUSOUT A
37-40
29,30 14 16
K3107 PSUS
1
18 20
PN_MUTE 23
14
Q3113, Q3127
XNR-U 21
15
XSUS-B 5
18
17
XSUS-D 9
16
XSUS-G 11
18
PLD
To X CONNECTOR ASSY
XSUS-MSK 13
16
2
IC3001 TC74ACT541FT
XCP-MSK
XCP-MSK 15
15
XNR-D1 17
17
14
10
IC3004 TC74ACT540FT
IC3008 PE1012A
Photo coupler
3
IC3110 TND301S
XNR-D2
CN3101 X1
+15V
DGND
VRN UVP
2
XDRIVE P.D VRN-300V
XDRIVE_PD
VRN OVP
XDC_DC_PD
VSUS
VSUS 225V
SUSGND 11
PDP-433PE, PDP-433PU
SUSGND
35
C B A
PDP-433PE, PDP-433PU
Y5 IC5V
IC2504 TC74ACT540FT
CN2501 CN2502
To SCAN ASSY (Lower)
VH
IC2001 TC74ACT541FT
OC2-2
Photo Coupler
VH
IC2516 HCPL-M611
Y3
IC2503 TC74ACT540FT
14
+13.5V
16 18 20
-9V
OC2-2 PN_MUTE YPR-U1 YPR-U2 YSUS-B YSUS-U YSUS-D YOFS YSUS-G YCP-MSK YSUS-MSK YSOFT-D DEW_DET
33 24 19 21 9 10 12 18 13 16 15 22 46
IC2004 TC74ACT541FT
YPR-U1
14 16 18 20
Y2
IC2006 PE1013
YSUS-MSK
Photo Coupler
Q2102
YSOFT-D
IC2202 HCPL-M611
+15V D. GND +13.5V -9V YDRIVE_PD YDC_DC_PD VOFS_ADJ VSUS VSUS SUSGND SUSGND
1 2 3 4 5 6 7 10 11 13 14
IC5V UVP
VF+ VF-
VOFS
SUSGND
VH UVP VH OVP
VH D-D CONV.
36
1 2
PDP433PE, PDP-433PU
K2203
37-40 SUSOUT A 29,30
B
IC2212 TND301S Q2219 Q2218 Q2215 K2220 PSUS
IC2213 TND301S Q2221 K2212 IC2216 TND301S Q2217 Q2226 Q2227 Q2220
TO Y CONNECTOR ASS'Y
5V 15V Vsus
IC2201 TC74ACT541FT
2-9
11-18
PSUS Q2210
IC2204 TND301S
SUSGND Q2211
IC2210 TND301S
Q2212
37
5 6 7 8
PDP-433PE, PDP-433PU
+60V ADRGND
CN8801 H : V MID CLAMP OFF L : V MID CLAMP ON
P.D. Output Block V MID SW ADRK EMG1 +12V DGND ADR-B ADR-U ADR-D ADRK. PD
CN8802 IC8801 (DC+AC) (-AC) Q8803, Q8831
BUFF Block
Inversion Block
IC8801
+5V REG
D8804 5V
Additional Block
IC8802
(DC)
CLK
Flip / Flop
IC8802
IC8803
CLR
38
1 2 3 4
PDP-433PE, PDP-433PU
CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. REPLACE ONLY WITH SAME TYPE NO. ICP-S1.0 MFD BY ROHM CO., LTD. FOR IC6704.
ICP-S1, 0
IC6704 C6703 - C6708
Address Resonance Output Block ADROUT ADRGND VADR DGND +12V ADR-B ADR-U ADR-D SW
CN6701
ADR-B Pre-Drive
IC6701
ADR-B Drive
Q6701, Q6704
ADR-U Pre-Drive
ADR-U Drive
L6704
ADR OUT
IC6702
Q6702, Q6705
ADR-D Pre-Drive
IC6703
ADR-D Drive
Q6703, Q6712
ADRGND
39
1 2 3 4
PDP-433PE, PDP-433PU
HZ LBLK HBLK LE CLK DATA_R DATA_G DATA_B DATA_R DATA_G DATA_B DATA_R DATA_G DATA_B DATA_R DATA_G DATA_B DATA_R DATA_G DATA_B DATA_R DATA_G DATA_B DATA_R DATA_G DATA_B DATA_R DATA_G DATA_B
Q6502, Q6503
Buffer
IC6501
CN6501
40
1 2 3 4
PDP-433PE, PDP-433PU
IC5201 (NJM2193L)
No. Voltage (V) No. Voltage (V) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 5.95 5.94 5.84 5.98 5.98 5.97 5.98 5.98 5.98 5.97 5.97 5.98 5.96 5.98 0 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 11.91 0 0 5.98 5.91 5.97 5.98 5.98 5.98 5.97 5.98 5.98 5.84 5.94 5.95
IC5002 (LA4628)
No. Voltage (V) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 1.6 7.5 0 3.37 2.29 1.6 1.97 7.3 7.3 0 7.3 0 7.3 15
A22 A24
J5003
8 22
IC5202 14 (CXA2021S) 1 Audio Pre-Amp. 9 L R R+ R L+ L
CN5001
4 6
L R
2 3 5 6
30
L R
1 6
9 11 13
11 7 8 11 12 13 14
STB SW A_MUTE SCL SDA FOCUS SRS
12
17
18
SP TERMINAL ASSY
SP21
CN5302
2 3 5 6
R+ R L+ L
L5301 ATF1206
CN5301
4 3 1 2
SPEAKER TERMINAL
L5352 ATF1206
41
1 2 3 4
PDP-433PE, PDP-433PU
3.2 WAVEFORMS
DIGITAL VIDEO ASSY
1
K1327 (VDI) K1328 (HDI) V: 2V/div. H: 4msec/div.
10
10
42
PDP-433PE, PDP-433PU
CH1 : D6706 Cathode CH2 : D6703 Cathode CH3 : D6708 Cathode V: 2V/div. (Input : VIDEO, Signal : Color bar)
CH1 GND CH2 GND CH3 GND CH1 GND
CH1 : IC6501 - pin 5 (HBLK) CH2 : IC6501 - pin 3 (LBLK) CH3 : IC6501 - pin 2 (HZ) V: 1V/div. (Input : VIDEO, Signal : Color bar)
CH1 GND CH2 GND CH3 GND CH1 CH2 GND CH3 GND GND
CH1 : IC8801 - pin 3 CH2 : IC8801 - pin 7 CH3 : IC8802 - pin 1 V: 2V/div. H: 2msec/div. (Input : VIDEO, Signal : Color bar)
H: 2msec/div
H: 2msec/div
H: 500nsec/div
H: 500nsec/div
CH1 : Q6706 Drain CH2 : Q6710 Soruse V: 10V/div. (Input : VIDEO, Signal : Color bar)
H: 2msec/div
CH2
GND
CH1 : Q9006 Base (CLAMP REF V) CH2 : D9010 Anode (MID) CH3 : Q9006 Collector V: 10V/div. H: 2msec/div. (Input : VIDEO, Signal : Color bar)
CH1
CH1
H: 500nsec/div GND
GND CH2
CH2
GND
CH1 : Q6706 Drain CH2 : Q6710 Soruse V: 10V/div. (Input : PC, Signal : Color bar)
GND
CH3 GND
2
H: 2msec/div
CH1
GND
CH2
GND
CH1 : Q9006 Base (CLAMP REF V) CH2 : D9010 Anode (MID) CH3 : Q9006 Collector V: 10V/div. H: 2msec/div. (Input : PC, Signal : Color bar)
CH1 GND CH2
CH1
H: 500nsec/div GND
CH2
GND GND CH3 GND
CH1 : Q6708 Drain CH2 : Q6710 Drain V: 10V/div. (Input : VIDEO, Signal : Color bar)
CH1
H: 2msec/div GND
CH2
GND
CH1
H: 500nsec/div GND
CH2
GND
43
PDP-433PE, PDP-433PU
AUDIO SECTION
Measurement condition
Video Input Signal Audio Input Signal Volume AV Selection SRS FOCUS : FULL FIELD COLOR-BAR : 1kHz Sine Carve 0.2Vrms : 60 (MAX) : STANDARD : OFF : OFF
CH1
CH2
GND and the speaker output (- side) becomes a short state on the oscilloscope.
10 Speaker
SP TERMINAL ASSY
SP TERMINAL ASSY
4
IC5002 - pin 1 (IN1) GND V: 0.1V/div. H: 0.2msec/div.
4.4V
1.6V
0V
7.3V
5.8V
7.3V
7.3V
10
5.9V
7.3V
0V
44
PDP-433PE, PDP-433PU
Sustain Waveforms
Sustain Waveform (1 field)
ch 1 : K3107 (X.PSUS) - K3201 (SUSGND) V: 100V/div. H: 2msec/div. ch 2 : K2220 (Y.PSUS) - K2219 (SUSGND) V: 100V/div. H: 2msec/div.
Sustain Waveform
ch 1 : K2220 (Y.PSUS) - K2219 (SUSGND) V: 100V/div. H: 500nsec/div. ch 2 : K2028 (YSUS_U) - K2024 (DGND) V: 10V/div. H: 500nsec/div. ch 3 : K2027 (YSUS_B) - K2024 (DGND) V: 10V/div. H: 500nsec/div. ch 4 : K2029 (YSUS_D) - K2024 (DGND) V: 10V/div. H: 500nsec/div. ch 5 : K2037 (YSUS_G) - K2024 (DGND) V: 10V/div. H: 500nsec/div.
45
PDP-433PE, PDP-433PU
Mark No. NOTES: Part 5. PCB Description LIST No. PARTS Mark No. Description Part No.
Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List. The mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. When ordering resistors, first convert resistance values into code form as shown in the following examples.
Ex.1 When there are 2 effective digits (any digit apart from 0), such as 560 ohm and 47k ohm (tolerance is shown by J=5%, and K=10%). 561 ........................................................ RD1/4PU 5 6 1 J 560 56 101 473 ........................................................ RD1/4PU 4 7 3 J 47k 47 103 0.5 R50 ..................................................................................... RN2H R 5 0 K 1 1R0 ..................................................................................... RS1P 1 R 0 K Ex.2 When there are 3 effective digits (such as in high precision metal film resistors). 5621 ...................................................... RN1/4PC 5 6 2 1 F 5.62k 562 101
Mark No.
NSP NSP NSP NSP NSP NSP NSP NSP NSP NSP NSP NSP NSP NSP NSP
Description
Part No.
AWV1927 AWZ6666 AWZ6667 AWZ6672 AWZ6673 AWZ6674 AWZ6675 AWZ6676 AWZ6677 AWV1928 AWZ6668 AWZ6669 AWZ6678 AWZ6679 AWZ6680 AWZ6681 AWZ6682 AWV1930 AWV1931 AWZ6683 AWZ6692 AWZ6693 AWV1929 AWV1923 AWZ6654 AWZ6655 AWZ6656 AWZ6657 AWZ6658 AWZ6660 AWV1935 AWZ6687 AWZ6688
Mark No.
Description
Part No.
LIST OF ASSEMBLIES
SCAN FUKUGO ASSY SCAN (A) ASSY SCAN (B) ASSY X CONNECTOR (A) ASSY X CONNECTOR (B) ASSY BRIDGE A ASSY BRIDGE B ASSY BRIDGE C ASSY BRIDGE D ASSY ADDRESS FUKUGO ASSY CLAMP A ASSY CLAMP B ASSY ADR CONNECT A ASSY ADR CONNECT B ASSY ADR CONNECT C ASSY ADR CONNECT D ASSY ADR RESONANCE ASSY X DRIVE ASSY HD Y DRIVE ASSY Y DRIVE ASSY SUB ADDRESS A ASSY SUB ADDRESS B ASSY DIGITAL VIDEO ASSY NSP HD FUKUGO ASSY MR INTERFACE ASSY LED ASSY FRONT KEY ASSY FRONT KEY CONN ASSY IR (P) ASSY THERMAL SENSOR ASSY HD AUDIO ASSY AUDIO AMP ASSY SP TERMINAL ASSY
CAPACITORS
C6001,C6002,C6011,C6012 (0.1F/250V) C6021,C6022,C6031,C6032 (0.1F/250V) C6041,C6042,C6051,C6052 (0.1F/250V) C6004,C6005,C6009,C6013,C6015 C6020,C6026,C6027,C6029,C6033 C6038,C6040,C6044,C6048,C6049 C6054,C6058-C6060,C6062-C6066 C6007,C6008,C6014,C6019,C6025 C6028,C6035,C6039,C6046,C6047 C6056,C6057 C6003,C6006,C6017,C6018 C6023,C6024,C6034,C6037,C6043 C6045,C6053,C6055 C6010,C6016,C6030,C6036,C6050 C6061 ACG1088 ACG1088 ACG1088 CCSRCH151J50 CCSRCH151J50 CCSRCH151J50 CCSRCH151J50 CCSRCH181J50 CCSRCH181J50 CCSRCH181J50 CCSRCH390J50 CCSRCH390J50 CCSRCH390J50 CKSRYF104Z16 CKSRYF104Z16
RESISTORS
R6007,R6012,R6021,R6028,R6032 R6040 Other Resistors RAB4C221J RAB4C221J RS1/16S AKP1218 AKX9002 AKX9002 J
OTHERS
CN6001 15P CONNECTOR K6001,K6012,K6018,K6025,K6031 TEST PIN K6038,K6044 TEST PIN
NSP
46
PDP-433PE, PDP-433PU
Mark No. Description Part No.
ACG1088 ACG1088 ACG1088 CCSRCH151J50 CCSRCH151J50 CCSRCH151J50 CCSRCH151J50 CCSRCH151J50 CCSRCH181J50 CCSRCH181J50 CCSRCH181J50 CCSRCH390J50 CCSRCH390J50 CCSRCH390J50 CKSRYF104Z16 CKSRYF104Z16
Mark No.
Description
Part No.
ACG1098
CAPACITORS
C6201,C6202,C6212,C6213 (0.1F/250V) C6222,C6223,C6232,C6233 (0.1F/250V) C6242,C6243,C6252,C6253 (0.1F/250V) C6203,C6205,C6206,C6210,C6215 C6219,C6220,C6227,C6229,C6231 C6235,C6236,C6240,C6244,C6246 C6251,C6255,C6259,C6260 C6262-C6266 C6208,C6209,C6217,C6218,C6226 C6230,C6238,C6239,C6245,C6250 C6257,C6258 C6204,C6207,C6214,C6216 C6224,C6225,C6234,C6237 C6248,C6249,C6254,C6256 C6211,C6221,C6228,C6241,C6247 C6261
CAPACITORS
C6431,C6432 (0.1F/100V)
OTHERS
CN6431 PH CONNECTOR B4B-PH-SM3
BRIDGE C ASSY
SEMICONDUCTORS
D6441,D6442 D1FL20U(S)
CAPACITORS
C6441,C6442 (0.1F/100V) ACG1098
OTHERS
CN6441 PH CONNECTOR B4B-PH-SM3
RESISTORS
R6207,R6209,R6222,R6228,R6232 R6239 Other Resistors RAB4C221J RAB4C221J RS1/16S J
BRIDGE D ASSY
SEMICONDUCTORS
D6451,D6452 D1FL20U(S)
OTHERS
CN6201 15P CONNECTOR K6202,K6212,K6219,K6225,K6231 TEST PIN K6239,K6244 TEST PIN AKP1218 AKX9002 AKX9002
CAPACITORS
C6451,C6452 (0.1F/100V) ACG1098
OTHERS
CN6451 PH CONNECTOR B4B-PH-SM3
CLAMP A ASSY
SEMICONDUCTORS
D6461,D6462 D1FL20U(S)
CAPACITORS
C6461,C6462 (0.1F/100V) ACG1098
OTHERS
CN6461 PH CONNECTOR B4B-PH-SM3
BRIDGE A ASSY
SEMICONDUCTORS
D6421,D6422 D1FL20U(S)
CLAMP B ASSY
SEMICONDUCTORS
D6471,D6472 D1FL20U(S)
CAPACITORS
C6421,C6422 (0.1F/100V) ACG1098
CAPACITORS
C6471,C6472 (0.1F/100V) ACG1098
OTHERS
CN6421 PH CONNECTOR B4B-PH-SM3
OTHERS
CN6471 PH CONNECTOR B4B-PH-SM3
BRIDGE B ASSY
SEMICONDUCTORS
D6431,D6432 D1FL20U(S)
47
PDP-433PE, PDP-433PU
Mark No. Description Part No. Mark No. Description Part No.
COILS
L6501,L6502 (22H/0.11A) ATH1081
COILS
L6801,L6802 (22H/0.11A) ATH1081
CAPACITORS
C6504,C6513-C6520,C6528 (330pF/100V) C6531,C6533,C6534 (47F/6.3V) C6536-C6538 C6507-C6510,C6522-C6525,C6532 C6535 ACG1094 ACH1341 CCSRCH121J50 CKSRYF104Z16 CKSRYF104Z16
CAPACITORS
C6804,C6813-C6820,C6828 (330pF/100V) C6831,C6833,C6834 (47F/6.3V) C6836-C6838 C6807-C6810,C6822-C6825,C6832 C6835 ACG1094 ACH1341 CCSRCH121J50 CKSRYF104Z16 CKSRYF104Z16
RESISTORS
R6519-R6522,R6526,R6528 R6530,R6531,R6534-R6537,R6541 R6543,R6545,R6547 R6516 Other Resistors RAB4C100J RAB4C100J RAB4C100J RAB4C473J RS1/16S
RESISTORS
R6819-R6822,R6826,R6828 R6830,R6831,R6834-R6837,R6841 R6843,R6845,R6847 R6816 Other Resistors RAB4C100J RAB4C100J RAB4C100J RAB4C473J RS1/16S
OTHERS
CN6501 55P CONNECTOR AKM1202
OTHERS
CN6801 55P CONNECTOR AKM1202
COILS
L6601,L6602 (22H/0.11A) ATH1081
COILS
L6901,L6902 (22H/0.11A) ATH1081
CAPACITORS
C6604,C6613-C6620,C6628 (330pF/100V) C6631,C6633,C6634 (47F/6.3V) C6636-C6638 C6607-C6610,C6622-C6625,C6632 C6635 ACG1094 ACH1341 CCSRCH121J50 CKSRYF104Z16 CKSRYF104Z16
CAPACITORS
C6904,C6913-C6920,C6928 (330pF/100V) C6931,C6933,C6934 (47F/6.3V) C6936-C6938 C6907-C6910,C6922-C6925,C6932 C6935 ACG1094 ACH1341 CCSRCH121J50 CKSRYF104Z16 CKSRYF104Z16
RESISTORS
R6619-R6622,R6626,R6628 RAB4C100J R6630,R6631,R6634-R6637,R6641RAB4C100J R6643,R6645,R6647 RAB4C100J R6616 RAB4C473J Other Resistors RS1/16S
RESISTORS
R6919-R6922,R6926,R6928 R6930,R6931,R6934-R6937,R6941 R6943,R6945,R6947 R6916 Other Resistors RAB4C100J RAB4C100J RAB4C100J RAB4C473J RS1/16S
OTHERS
CN6601 55P CONNECTOR AKM1202
OTHERS
CN6901 55P CONNECTOR AKM1202
48
PDP-433PE, PDP-433PU
Mark No. Description Part No. Mark No. Description Part No.
COILS
L6704 CHOKE COIL ATH1121
CAPACITORS
C6716,C6718 (1.00F) C6720,C6721 (0.01F/100V) C6722 (0.0068F/100V) C6703-C6708 (56F/80V) C6701,C6702,C6709 C6710,C6711,C6713 ACE1159 ACG1101 ACG1102 ACH1347 CEHV470M16 CKSRYF104Z16
COILS
L3206,L3207 ATH1112 RADIAL LEAD INDUCTOR L3201,L3204 CHOKE COIL ATH1113 L3202,L3205,L3210,L3211 ATH1118 CHOKE COIL L3101 L3107,L3108 L3103 LFEA100J LFEA101J LFEA470J
RESISTORS
All Resistors RS1/16S J
OTHERS
CN6701 CN6702 CN6703 23P CONNECTOR PH CONNECTOR PH CONNECTOR AKP1221 B4B-PH-SM3 B5B-PH-SM3
CAPACITORS
X DRIVE ASSY
[X LOGIC BLOCK] SEMICONDUCTORS
IC3003 IC3004 IC3001,IC3008 PE1012A TC74ACT540FT TC74ACT541FT
C3205,C3206,C3212,C3213 (1.5F) C3225,C3226 (1.5F) C3131,C3139,C3143 (0.1F/630V) C3223,C3224 (100pF/500V) C3132 (47F/350V) C3200-C3202,C3207-C3209 (330F/315V) C3214-C3221 C3112,C3133,C3203,C3210 C3102,C3107,C3115,C3204,C3211 C3101 C3104,C3106,C3134,C3141 C3135 C3154,C3163 C3103,C3105,C3108,C3109,C3111 C3113,C3114,C3117,C3130,C3140 C3147 J
ACE1160 ACE1160 ACG1092 ACG1100 ACH1346 ACH1348 CCSRCH331J50 CEHAT101M16 CEHAT101M25 CEHAT221M25 CEHAT470M16 CEHAT470M25 CKSRYB332K50 CKSRYF104Z50 CKSRYF104Z50 CKSRYF104Z50
COIL
L3001 LFEA100J
CAPACITORS
C3005 C3001,C3003,C3004,C3006 CEHAT470M16 CKSRYF104Z50
RESISTORS
R3009-R3012 R3001,R3003,R3026,R3029 R3002,R3005,R3030,R3033 Other Resistors RAB4C0R0J RAB4C470J RAB4C472J RS1/16S
RESISTORS
R3183,R3184,R3187 R3113,R3114,R3121,R3122,R3126 R3132,R3140,R3141 R3212,R3217,R3230,R3234,R3237 R3240,R3242,R3245 R3250-R3253 R3134,R3163 R3103 R3109 R3102 ACN1156 RAB4C100J RAB4C100J RS1/10S184J RS1/10S184J RS1/16S3300F RS1/2S100J RS1/2S102J RS1/2S2R2J RS1/2S561J
OTHERS
K3001,K3003,K3004,K3008,K3010 TEST PIN K3012-K3015,K3017,K3018 TEST PIN CN3001 30P CONNECTOR AKX9002 AKX9002 KF050HA30L
49
PDP-433PE, PDP-433PU
Mark No. Description Part No.
RS1MMF101J RS1MMF122J RS1MMF563J RS2MMF181J ACP1089 RS1/16S J
Mark No.
Description
Part No.
Y DRIVE ASSY
[Y DRIVE LOGIC BLOCK] SEMICONDUCTORS
IC2006 IC2007 IC2001,IC2003-IC2005 Q2121 Q2101,Q2102 D2101 PE1013B TC74ACT540FT TC74ACT541FT 2SK2201 HN1C01FU 1SS355
OTHERS
3101 SPACER K3102-K3104 TEST PIN KN3105-KN3114 GROUND PLATE CN3101 13P PLUG CN3102 3P PLUG AEH1049 AKX9002 ANK-142 KM250MA13 KM250MA3
COIL
L2001 LFEA100J
CAPACITORS
C2101 C2103 C2003 C2001,C2004,C2005,C2007,C2008 C2010,C2102,C2104,C2121 CEHAT100M50 CEHAT1R0M50 CEHAT470M16 CKSRYF104Z50 CKSRYF104Z50
RESISTORS
R2015-R2018 R2001,R2002,R2005,R2011 R2037,R2038 R2035,R2036,R2039,R2040 Other Resistors RAB4C0R0J RAB4C470J RAB4C470J RAB4C472J RS1/16S
OTHERS
CN2001 50P CONNECTOR K2001-K2005,K2009,K2010,K2013 TEST PIN K2021,K2027-K2029,K2037 TEST PIN K2039-K2041,K2053 TEST PIN 2101 SENSOR SCREW NUT AKM1201 AKX9002 AKX9002 AKX9002 AXX1057 BMZ20P040FMC NB20FMC
COIL
L3701 RADIAL LEAD INDUCTOR ATH1110
TRANSFORMER
T3701 ATK1153
CAPACITORS
C3701 (22F/315V) C3717 (47F/350V) C3704 C3706,C3711,C3714 C3712 C3705 C3703,C3707,C3708,C3710 C3715,C3716 ACH1345 ACH1346 CEHAT101M16 CEHAT101M25 CEHAT331M16 CKSQYF104Z50 CKSRYB104K16 CKSRYB104K16
RESISTORS
R3732 R3806 R3701-R3704,R3706-R3717 R3805 R3731 R3802 R3738,R3739 R3800,R3801 VR3701 (1k) Other Resistors RS1/16S1001F RS1/16S1802F RS1/16S1803F RS1/16S2702F RS1/16S3900F RS1/16S5601F RS1/2S102J RS1/2S823J ACP1089 RS1/16S J
50
PDP-433PE, PDP-433PU
Mark No. Description Part No. Mark No. Description Part No.
COILS
L2207 RADIAL LEAD INDUCTOR ATH1110 L2213,L2214 ATH1112 RADIAL LEAD INDUCTOR L2206,L2211 CHOKE COIL ATH1113 L2208,L2212,L2215,L2216 ATH1118 CHOKE COIL L2210 LFEA100J L2203,L2205 LFEA101J L2201,L2204 LFEA470J
COILS
L2501-L2503 LFEA100J
CAPACITORS
C2228,C2230,C2231,C2250-C2252 (1.5F) C2209,C2210 (0.1F/630V) C2233,C2248 (100pF/500V) C2211 (47F/350V) C2216,C2217,C2219,C2234-C2236 (330F/315V) C2253-C2260 C2221,C2225,C2226,C2246 C2204,C2227,C2237,C2240,C2247 C2202 C2232 C2218,C2224,C2229 C2212,C2214 C2264,C2270 C2201,C2203,C2205,C2208,C2213 C2220,C2222,C2223,C2238,C2239 C2241,C2242 ACE1160 ACG1092 ACG1100 ACH1346 ACH1348 CCSRCH331J50 CEHAT101M16 CEHAT101M25 CEHAT221M25 CEHAT331M2A CEHAT470M16 CEHAT470M25 CKSRYB472K50 CKSRYF104Z50 CKSRYF104Z50 CKSRYF104Z50
CAPACITORS
C2506,C2527 C2502 C2524,C2525 C2501,C2503-C2505,C2507,C2508 C2513,C2515-C2517,C2519,C2530 CEHAT220M2D CEHAT221M16 CEHAT470M16 CKSRYF104Z50 CKSRYF104Z50
RESISTORS
R2502,R2504 Other Resistors RAB4C101J RS1/16S J
OTHERS
CN2501,CN2502 15P CONNECTOR AKM1200
RESISTORS
R2235,R2273,R2291,R2305,R2315 R2317,R2342 R2253,R2256,R2270,R2283,R2332 R2338,R2354,R2355 R2358-R2361 R2263,R2264 R2203 R2209 R2202 R2278,R2303 R2233,R2234 R2274,R2275 R2298,R2299 R2277 R2276 VR2201-VR2204 (1k) Other Resistors RAB4C100J RAB4C100J RS1/10S184J RS1/10S184J RS1/16S3300F RS1/2S100J RS1/2S102J RS1/2S2R2J RS1/2S561J RS1MMF101J RS1MMF152J RS1MMF471J RS2MMF3R3J RS3LMFR47J RS3LMFR56J ACP1089 RS1/16S J
OTHERS
2201 SPACER K2211,K2214-K2217 TEST PIN KN2201-KN2210 GROUND PLATE CN2201 15P PLUG CN2202 3P PLUG AEH1049 AKX9002 ANK-142 KM250MA15 KM250MA3
COIL
L2701 RADIAL LEAD INDUCTOR ATH1110
TRANSFORMERS
T2702 T2703 T2701 ATK1150 ATK1151 ATK1152
51
PDP-433PE, PDP-433PU
Mark No. Description Part No.
ACH1345 CEHAT101M16 CEHAT101M25 CEHAT101M2A CEHAT101M2C CEHAT221M25 CEHAT331M16 CEHAT331M25 CEHAT470M16 CEHAT471M35 CKSRYB103K50 CKSRYB104K16 CKSRYB104K16 CKSRYB104K16 CKSRYB104K16 CKSRYB471K50 CKSRYF104Z50
Mark No.
Description
Part No.
CCSRCH101J50 CEHV100M16 CEHV100M35 CEHV470M16 CEVNP2R2M35 CKSRYF104Z16 CKSRYF104Z16
CAPACITORS
C2701,C2735 (22F/315V) C2706,C2725,C2737 C2709,C2718,C2720,C2739,C2745 C2708 C2740 C2704 C2715 C2746 C2723,C2751 C2712 C2711 C2705,C2713,C2714,C2719 C2721,C2722,C2724,C2727,C2729 C2731,C2733,C2736,C2742,C2743 C2747-C2749 C2728,C2730 C2707,C2738
CAPACITORS
C8806 C8822 C8804 C8801,C8808 C8807 C8802,C8803,C8805,C8809-C8817 C8820,C8821
RESISTORS
R8806,R8807,R8837,R8838,R8841 R8858 R8828,R8829,R8832,R8846,R8864 R8826,R8827,R8839,R8840 R8833 R8859 R8801,R8802 R8803-R8805 Other Resistors RS1/16S1002D RS1/16S1202D RS1/16S2202D RS1/16S4701D RS1/16S4702F RS1/16S5602F RS1/2S1R5J RS1/2S2R2J RS1/16S J
RESISTORS
R2735,R2791 R2780 R2715,R2728,R2733 R2787 R2766 R2785 R2777,R2786 R2776 R2705,R2706,R2709,R2710,R2778 R2781 R2783 R2734,R2736 R2779 R2773 R2784 R2782 R2744-R2746,R2748-R2753 R2711,R2716,R2767,R2770 R2788,R2792 R2771,R2772 R2712 VR2702,VR2703 (1k) VR2701 (2.2k) Other Resistors RS1/16S1000F RS1/16S1103F RS1/16S1201F RS1/16S1302F RS1/16S1501F RS1/16S1503F RS1/16S1802F RS1/16S2702F RS1/16S3002F RS1/16S3002F RS1/16S4701F RS1/16S4702F RS1/16S5102F RS1/16S5601F RS1/16S5602F RS1/16S6801F RS1/16S9102F RS1/2S102J RS1/2S561J RS1/2S823J RS3LMF272J ACP1089 ACP1090 RS1/16S J
OTHERS
CN8803 CN8801 CN8802 23P CONNECTOR PH CONNECTOR PH CONNECTOR AKM1205 S3B-PH-SM3 S8B-PH-SM3
COILS
L8901 CHOKE COIL (100H/0.45A) ATH1074 L8902,L8903 COIL (22H/0.11A) ATH1081
CAPACITORS
C8906 C8922 C8904 C8901,C8908 C8907 C8902,C8903,C8905,C8909-C8917 C8920,C8921 CCSRCH101J50 CEHV100M16 CEHV100M35 CEHV470M16 CEVNP2R2M35 CKSRYF104Z16 CKSRYF104Z16
RESISTORS
R8906,R8907,R8937,R8938,R8941 R8958 R8928,R8929,R8932,R8946,R8964 R8926,R8927,R8939,R8940 R8933 R8959 R8901,R8902 R8903-R8905 Other Resistors RS1/16S1002D RS1/16S1202D RS1/16S2202D RS1/16S4701D RS1/16S4702F RS1/16S5602F RS1/2S1R5J RS1/2S2R2J RS1/16S J
COILS
L8801 CHOKE COIL (100H/0.45A) ATH1074 L8802,L8803 COIL (22H/0.11A) ATH1081
52
PDP-433PE, PDP-433PU
Mark No. Description
23P CONNECTOR PH CONNECTOR PH CONNECTOR
Part No.
AKM1205 S3B-PH-SM3 S8B-PH-SM3
Mark No.
Description
Part No.
OTHERS
CN8903 CN8901 CN8902
CAPACITORS
C1213,C1243-C1245 C1235,C1236 C1225,C1232 C1201-C1203,C1206-C1211 C1214-C1216,C1218,C1219 C1223,C1224,C1226,C1227,C1229 C1237,C1238,C1241,C1242,C1247 C1234 C1233 C1204,C1205,C1212,C1217 C1221,C1222,C1228,C1230,C1231 C1239,C1240,C1246,C1248-C1250 CCSRCH470J50 CCSRCH7R0D50 CEV470M6R3 CKSRYB102K50 CKSRYB102K50 CKSRYB102K50 CKSRYB102K50 CKSRYB103K50 CKSRYB472K50 CKSRYF104Z16 CKSRYF104Z16 CKSRYF104Z16
FILTERS
F1001-F1006 EMI FILTER ATF1194
CAPACITORS
C1001-C1008 CKSRYF104Z16
RESISTORS
R1044 R1001-R1007,R1036,R1063-R1069 R1008-R1017,R1019,R1020,R1027 R1032,R1034,R1035,R1037,R1038 R1040-R1043,R1048,R1049 R1051-R1054 Other Resistors RAB4C101J RAB4C103J RAB4C470J RAB4C470J RAB4C470J RAB4C470J RS1/16S J
RESISTORS
R1209,R1214,R1245 R1242 R1207 R1213,R1216 Other Resistors RAB4C101J RAB4C103J RAB4C123J RAB4C473J RS1/16S
OTHERS
CN1003,CN1004 50P CONNECTOR K1001 TEST PIN CN1001 PH CONNECTOR AKM1201 AKX9002 B12B-PH-SM3
OTHERS
X1201 CERAMIC RESONATOR ASS1159 (16MHz) CN1203 PH CONNECTOR B3B-PH-SM3 CN1201,CN1202 8P PLUG CKS3130
CAPACITORS
C1123,C1124 C1101 C1102,C1109,C1110,C1112-C1116 C1129-C1132 C1117,C1121 C1120 C1103-C1108,C1111,C1118,C1119 C1122,C1125-C1128 CCSRCH7R0D50 CEV101M4 CKSRYB102K50 CKSRYB102K50 CKSRYB103K50 CKSRYB472K50 CKSRYF104Z16 CKSRYF104Z16
FILTERS
F1301-F1304,F1501-F1505 EMI FILTER F1601-F1605 EMI FILTER ATF1194 ATF1194
RESISTORS
R1104,R1107,R1110,R1113,R1114 R1116,R1121,R1124,R1127,R1129 R1128 Other Resistors RAB4C472J RAB4C472J RD1/4PU473J RS1/16S J
CAPACITORS
C1807 C1802 C1306,C1322,C1406,C1422,C1711 C1806 C1504-C1508,C1604-C1608,C1712 CCSRCH271J50 CEV100M16 CEV101M4 CEV101M4 CKSRYB102K50
OTHERS
K1101-K1104,K1107,K1108 AKX9002 TEST PIN X1101 CERAMIC RESONATOR ASS1160 (25MHz)
53
PDP-433PE, PDP-433PU
Mark No. Description Part No.
CKSRYF104Z16 CKSRYF104Z16 CKSRYF104Z16 CKSRYF104Z16 CKSRYF104Z16
Mark No.
Description
Part No.
MR INTERFACE ASSY
[INTERFACE BLOCK] SEMICONDUCTORS
IC4011 IC4007,IC4010 IC4005 IC4001 IC4002-IC4004 IC4013 IC4008,IC4009 IC4012 IC4006 Q4003,Q4004,Q4010 CXA1875AM M5223AFP M62320FP PQ05DZ51 PQ20VZ1U PST9228N TC74HC00AF TC74HC4066AF TC74VHCT541AFT 2SA1162 2SC2712 DTC124EK HN1A01FU HN1B04FU HN1C01FU RN2902 1SS184 1SS355
RESISTORS
R1502,R1517,R1606,R1622 R1307,R1310-R1315,R1317,R1318 R1321,R1322,R1326-R1344,R1407 R1410-R1415,R1417,R1418 R1421,R1422,R1426-R1444 R1501,R1514,R1607,R1627,R1701 R1703-R1709,R1712-R1717 R1551,R1552 Other Resistors RAB4C101J RAB4C220J RAB4C220J RAB4C220J RAB4C220J RAB4C470J RAB4C470J RS1/2S680J RS1/16S
OTHERS
CN1701 50P CONNECTOR CN1501,CN1502,CN1504,CN1505 55P CONNECTOR CN1601,CN1602,CN1604,CN1605 55P CONNECTOR K1301,K1302,K1308,K1311-K1314 TEST PIN K1316,K1321,K1324,K1326-K1331 TEST PIN K1333,K1501,K1502,K1601,K1602 TEST PIN AKM1201 AKM1202 AKM1202 AKX9002 AKX9002 AKX9002
SWITCHES
S4001,S4004 ASH1010
CAPACITORS
C4023,C4036,C4037 C4025,C4032 C4029,C4030,C4053,C4054 C4001,C4004,C4005,C4008,C4010 C4012,C4013,C4016,C4041,C4042 C4034,C4038,C4050,C4056 C4043 C4027,C4028,C4033,C4051 C4002,C4003,C4006,C4007 C4014,C4015,C4017-C4019,C4024 C4026,C4031,C4035,C4039,C4040 C4044-C4047,C4049,C4052,C4055 2SC2712 DTC143EK HN1C01FU 1SS355 HZU2.2B UDZ3.6B UDZS5.1B UDZS6.8B CCSRCH102J50 CCSRCH220J50 CCSRCH471J50 CEAT101M10 CEAT101M10 CKSRYB105K6R3 CKSRYB474K10 CKSRYF103Z50 CKSRYF104Z16 CKSRYF104Z16 CKSRYF104Z16 CKSRYF104Z16
K1728,K1729 TEST PIN AKX9002 X1801 CRYSTAL RESONATOR ASS1146 (50.000MHz) CN1503,CN1603 PH CONNECTOR B8B-PH-SM3 CN1301 8P PLUG CKS3130 CN1702 30P CONNECTOR KF050HA30L
RESISTORS
R4019,R4035,R4054,R4066 R4056 R4007,R4014,R4015,R4117 R4106 R4107 R4098 R4078 R4074,R4094 R4075 R4057 R4124 R4004,R4005,R4115,R4116 R4093 R4006 Other Resistors RAB4C101J RAB4C471J RS1/16S1001F RS1/16S1002F RS1/16S1502F RS1/16S2201F RS1/16S2202F RS1/16S3301F RS1/16S4701F RS1/16S5601F RS1/16S5602F RS1/16S8200F RS1/16S8201F RS2MMF2R2J RS1/16S J
CAPACITORS
C1904,C1906,C1912 CEV220M16 C1901-C1903,C1905,C1907-C1911 CKSRYF104Z16
RESISTORS
R1935,R1936 Other Resistors RS1/2S680J RS1/16S J
OTHERS
K1901-K1906 TEST PIN 1901 DC-DC CONVERTER CN1901 PH CONNECTOR AKX9002 AXY1054 B13B-PH-SM3
54
PDP-433PE, PDP-433PU
Mark No. Description Part No.
AKM1180 AKP1194 AKP1216 B3B-PH-SM3 B7B-PH-SM3 CKS3130
Mark No.
Description
Part No.
OTHERS
CN4004,CN4005 50P CONNECTOR CN4002 20P SOCKET CN4003 24P DVI SOCKET CN4006,CN4009 3P PH CONNECTOR CN4007 CN4008 7P PH CONNECTOR 8P PLUG
OTHERS
K4201-K4207 TEST PIN AKX9002 X4201 CRYSTAL RESONATOR ASS1163 (16.000MHz)
CAPACITORS
C4408,C4417 C4403 C4407 C4402 C4425,C4426 C4410 CEANP100M50 CEAT101M10 CEAT101M25 CEAT220M50 CEAT470M25 CKSRYF104Z16
RESISTORS
All Resistors RS1/16S J
OTHERS
CN4403 CN4404 7P PH CONNECTOR 8P PH CONNECTOR B7B-PH-SM3 B8B-PH-SM3
FILTERS
F4201,F4203-F4205 EMI FILTER ATF1194
LED ASSY
SEMICONDUCTOR
D4751 AEL1170
CAPACITORS
C4208,C4210,C4215,C4222,C4230 C4255,C4257 C4262 C4206,C4207,C4212,C4214,C4217 C4219,C4220,C4224,C4227,C4229 C4231-C4233,C4236,C4241,C4244 C4248,C4253,C4254,C4258 C4239,C4242,C4246,C4250 C4202,C4237,C4238 C4264 C4265 C4260 C4263 C4201,C4203-C4205,C4209,C4211 C4213,C4216,C4218,C4221,C4225 C4234,C4235,C4240,C4243,C4245 C4247,C4251,C4252,C4256,C4259 C4261 C4223,C4226,C4228,C4249 C4266-C4270 CCSRCH331J50 CCSRCH331J50 CCSRCH471J50 CCSRCH820J50 CCSRCH820J50 CCSRCH820J50 CCSRCH820J50 CEAT101M10 CEAT470M10 CKSRYB103K50 CKSRYB105K6R3 CKSRYB472K50 CKSRYB474K10 CKSRYF104Z16 CKSRYF104Z16 CKSRYF104Z16 CKSRYF104Z16 CKSRYF104Z16 CKSRYF105Z10 CKSRYF105Z10
OTHERS
CN4751 3P PH CONNECTOR S3B-PH-SM3
CAPACITORS
C4801-C4803 CKSRYF104Z16
RESISTORS
All Resistors RS1/16S J
OTHERS
CN4801 6P FFC CONNECTOR AKM1208
RESISTORS
R4213-R4217,R4245,R4247 R4253-R4255 R4241 R4250 Other Resistors RAB4C181J RAB4C181J RAB4C680J RS1/16S5100D RS1/16S J
OTHERS
CN4851 CN4852 6P FFC CONNECTOR 4P PH CONNECTOR AKM1208 B4B-PH-SM3
55
PDP-433PE, PDP-433PU
Mark No. Description Part No. Mark No. Description Part No.
CEHAT472M25 CEHAT4R7M50 CEHAT4R7M50 CEHATR47M50 CFTLA103J50 CFTLA103J50 CFTLA104J50 CFTLA104J50 CFTLA224J50 CFTLA333J50 CFTLA473J50 CKCYB103K50 CKCYB103K50 CQMA122J50 CQMA222J50 CQMA392J50
IR (P) ASSY
SEMICONDUCTORS
Q4901 D4901 2SC2712 1SS355
C5013 C5208,C5211,C5212,C5218 C5222,C5223,C5234 C5045 C5014,C5204,C5217,C5220,C5228 C5237 C5035,C5046,C5053,C5056,C5216 C5221,C5239 C5214,C5230 C5225 C5219,C5236 C5003,C5006,C5016,C5042,C5207 C5210 C5043,C5052,C5205,C5229 C5224 C5215,C5231
CAPACITORS
C4901 C4902 C4903 C4904 CEV470M6R3 CKSRYB103K50 CKSRYB472K50 CKSRYF104Z16
RESISTORS
All Resistors RS1/16S J
OTHERS
4901
REMOTE RECEIVER UNIT GP1UM26RK
RESISTORS
OTHERS
J5003 6P HOUSING WIRE J5002 8P HOUSING WIRE 5006 FERRITE CORE HOLDER KN5001 GROUND PLATE 5001,5002,5004,5005 SCREW ADX2729 ADX2731 AEC1818 ANK-142 VBB30P100FNI
CAPACITORS
C4705 C4704 C4701 C4702,C4703 CEV470M6R3 CKSRYB103K50 CKSRYF104Z16 CKSRYF105Z10
RESISTORS
R4706,R4708 Other Resistors RS1/16S3001F RS1/16S J
SP TERMINAL ASSY
COILS
L5301,L5352 LINE FILTER ATF1206
CAPACITORS
RESISTORS
R5301,R5302,R5351,R5352 RD1/2MMF100J
OTHERS
CN5301 4P SPEAKER TERMINAL AKE1058
COIL
L5001 FERRITE CORE ATX1037
CAPACITORS
C5203,C5227 C5213,C5226 C5232,C5233,C5235 C5015,C5029,C5033,C5201,C5206 C5242 C5032,C5034 C5044,C5050,C5051 C5005 C5238 C5002 CCCCH221J50 CEHANP220M25 CEHAT100M50 CEHAT101M25 CEHAT221M25 CEHAT2R2M50 CEHAT330M25 CEHAT331M16 CEHAT470M16 CEHAT471M16
56
PDP-433PE, PDP-433PU
6. ADJUSTMENT
6.1 SERVICE FACTORY MODE
Service factory mode uses an OSD function of the Media Receiver (PDP-R03E or PDP-R03U). Perform the adjustment and setting in the state that this unit and Media Receiver are connected by the system. Plasma display cannot use a factory mode by being simple.
Function
One line moves the selection cursor of the adjustment item up. One line moves the selection cursor of the adjustment item down. +1 raises a adjustment value 1 reduces a adjustment value Perform page down (previous page) Perform page up (next page) 10 reduces a adjustment value +10 raises a adjustment value
57
PDP-433PE, PDP-433PU
Note 1: When use the adjustment exclusive use remote control unit with a [AA5F] code.
58
PDP-433PE, PDP-433PU
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
Item
Main software version information of the media receiver OSD version information of the media receiver IP/resize IC control software version information of the media receiver Text microcomputer software version information of the media receiver
Module microcomputer software version information of the PDP
Explanation
Panel microcomputer version information of the PDP Panel flash ROM version information of the PDP PDP model information Media receiver model information Media receiver model information PDP destination information Temperature information of panel temperature sensor on the PDP Media receiver accumulation operating time Media receiver accumulation operating time reset PDP accumulation operating time PDP accumulation operating time reset PDP accumulation pulse number PDP accumulation pulse number reset
Reference
01: PIONEER 50 inches, 02: PIONEER 43 inches, 11: SHARP 50 inches, 12: SHARP 43 inches
0: All SHARP destinations, Japanese and North America destinations of PIONEER, 3: European and general destinations of PIONEER This is internal temperature information. This is not establishment environment temperature. Turn the display to [ON] by pressing the "VOL +" key, then it becomes [0H] when pressing the "ENTER" key. Turn the display to [ON] by pressing the "VOL +" key, then it becomes [0H] when pressing the "ENTER" key.
Real accumulation pulse number becomes "indicated value *10,000,000 pulse".
Turn the display to [ON] by pressing the "VOL +" key, then it becomes [0] when pressing the "ENTER" key.
59
PDP-433PE, PDP-433PU
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Item
PDP_W/B table selection at VIDEO 50Hz PDP_W/B table selection at VIDEO 60Hz PDP_W/B table selection at PC RED_GAIN of PDP_W/B table 1 GREEN_GAIN of PDP_W/B table 1 BLUE_GAIN of PDP_W/B table 1 RED_OFS of PDP_W/B table 1 GREEN_OFS of PDP_W/B table 1 BLUE_OFS of PDP_W/B table 1 RED_GAIN of PDP_W/B table 2 GREEN_GAIN of PDP_W/B table 2 BLUE_GAIN of PDP_W/B table 2 RED_OFS of PDP_W/B table 2 GREEN_OFS of PDP_W/B table 2 BLUE_OFS of PDP_W/B table 2
Adjustable Range
1 or 2 1 or 2 1 or 2 0 to 255 0 to 255 0 to 255 0 to 999 0 to 999 0 to 999 0 to 255 0 to 255 0 to 255 0 to 999 0 to 999 0 to 999
Shipping Setting
2 1 1 Factory adjustment value Factory adjustment value Factory adjustment value Factory adjustment value Factory adjustment value Factory adjustment value Factory adjustment value Factory adjustment value Factory adjustment value Factory adjustment value Factory adjustment value Factory adjustment value
Storage Place
PDP PDP PDP PDP PDP PDP PDP PDP PDP PDP PDP PDP PDP PDP PDP
Caution in the PDP W/B (No.4 to 15) adjustment: Adjustment value is reflected without relation in input signal during adjustment to the actual PDP. For example, when operate a adjustment value of [MNTR HIGH1] during PAL input, switch to the adjustment value operation of W/B table 1 while displaying PAL in the actual PDP. This is temporary. After adjustment, it becomes the W/B table 2 operation in the PAL input after restarted in the normal mode. It becomes an operation of the W/B table 1 adjustment value after adjustment in the NTSC input. As for the above example, table selection (No. 1 and 2) becomes the shipping setting.
60
PDP-433PE, PDP-433PU
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
No.
1 2 3 4 5 6 7 8
Item
Electric power setting at the PC, VIDEO 60Hz Electric power setting at VIDEO 50Hz VOFS voltage setting VSUS voltage setting SUS_B timing setting of X drive SUS_G timing setting of X drive SUS_B timing setting of Y drive SUS_G timing setting of Y drive
Adjustable Range
0 to 255 0 to 255 0 to 255 0 to 255 0 to 15 0 to 15 0 to 15 0 to 15
Shipping Setting
Factory adjustment value Factory adjustment value Factory adjustment value Factory adjustment value Factory adjustment value Factory adjustment value Factory adjustment value Factory adjustment value
Storage Place
PDP PDP PDP PDP PDP PDP PDP PDP
Adjustment item of this page is related in damage of the set when mistakes adjustment. When adjustment is needed, be enough careful to adjustment. Caution in the electric power setting (No. 1 and 2) adjustment: Adjustment value is reflected without relation in input signal during adjustment to the actual PDP. For example, when operate a adjustment value of [ABL VIDEO 60 PC] during PAL input, switch to the adjustment value operation of [ABL VIDEO 60 PC] while displaying PAL in the actual PDP. This is temporary. After adjustment, it becomes the [ABL VIDEO 50] operation in the PAL input after restarted in the normal mode. It becomes an operation of the [ABL VIDEO 60PC] adjustment value after adjustment in the NTSC input.
61
PDP-433PE, PDP-433PU
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
No.
1 2 3 4 5 6 7 Drive mode selection at PC
Item
Drive mode selection at VIDEO
Adjustable Range
0 to 5 0 to 5 OFF/ON OFF/ON 50/60/70 OFF/ OFF/
Shipping Setting
0 3 OFF OFF OFF OFF
Storage Place
PDP PDP PDP None None PDP PDP
Negative positive inversion mode Bright enhance Refresh rate at mask signal generation Pattern mask signal generation Full mask signal generation
Caution in the mask (generation test signal screen in the PDP inside) signal generation: A pattern mask and a full mask can use only either. Therefore, turn a full mask to OFF when uses a pattern mask. Also turn a pattern mask to OFF when uses a full mask. A pattern mask and a full mask are test signal screens occurring together in the PDP inside. Therefore, in the mask signal generation, it cannot confirm video inputting from OSD and the outside. When release mask setting or change of each setting or perform the confirmation of the adjustment or external input signal, perform key operation of the main unit button or the remote control unit. When operated something, stop the generation of the mask signal just after that for two seconds. Therefore, modification and adjustment of each setting and confirmation of the external input signal are possible.
62
PDP-433PE, PDP-433PU
Y DRIVE Assy
When repaired
1. VOFS/VH/IC5V voltage adjustment 2. Timing adjustment of pulse module
When replaced
1. SUSB ground timing adjustment 2. Panel white balance adjustment
When replaced
Remove IC1204 (24LC04(1) SN-TBB) from the former PC Board to replace, and install it to the new PC Board.
X DRIVE Assy
When repaired
1. VRN voltage adjustment 2. Timing adjustment of pulse module
MR INTERFACE Assy
1. Remove IC4201 from the former PC Board to replace, and install it to the new PC Board. 2. Set slide SW according to page 22.
When replaced
1. SUSB ground timing adjustment 2. Panel white balance adjustment
Y DRIVE Assy
X DRIVE Assy
MR INTERFACE Assy
PDP-433PE, PDP-433PU
6.3 ADJUSTMENT
VOFS/VH/IC5V Voltage Adjustment
Input Signal
Adjusting Point
Adjusting Method
VOFS (Offset voltage) adjustment Method 1 1. Write down a adjustment value of VOFS ADJ in the factory mode. 2. Set this adjustment value to center (128). 3. Adjust VR2701 so that the voltage between K2701 (VOFS) and K2703 (SUS GND) becomes 45V. 4. Return it to the value that wrote down a adjustment value of V-OFFSET in step 1. Method 2 1. Read the adjustment value of VOFS ADJ in the factory mode. 2. Adjust VR2701 so that the voltage between K2710 (VOFS) and K2703 (SUS GND) becomes following voltage 0.5V.
Input Command VOF000 VOF006 VOF013 VOF019 VOF026 VOF032 VOF038 VOF045 VOF051 VOF058 VOF064 VOF070 VOF077 VOF083 DAC Output 0.4 0.4984375 0.61328125 0.71171875 0.8265625 0.925 1.0234375 1.13828125 1.23671875 1.3515625 1.45 1.5484375 1.66328125 1.76171875 1.8765625 1.975 2.0734375 2.18828125 2.28671875 2.4015625 2.5 Setting Voltage 25 25.9375 27.03125 27.96875 29.0625 30 30.9375 32.03125 32.96875 34.0625 35 35.9375 37.03125 37.96875 39.0625 40 40.9375 42.03125 42.96875 44.0625 45 Input Command VOF134 VOF141 VOF147 VOF153 VOF160 VOF166 VOF172 VOF179 VOF185 VOF191 VOF198 VOF204 VOF211 VOF217 VOF223 VOF230 VOF236 VOF242 VOF249 VOF255 DAC Output 2.599212598 2.71496063 2.814173228 2.913385827 3.029133858 3.128346457 3.227559055 3.343307087 3.442519685 3.541732283 3.657480315 3.756692913 3.872440945 3.971653543 4.070866142 4.186614173 4.285826772 4.38503937 4.500787402 4.6 Setting Voltage 45.94488 47.04724 47.99213 48.93701 50.03937 50.98425 51.92913 53.0315 53.97638 54.92126 56.02362 56.9685 58.07087 59.01575 59.96063 61.06299 62.00787 62.95276 64.05512 65
White 100%
The symptom is case of mis-adjustment If the VOFS Voltage adjustment is not performed properly, dots like blinking luminance points appear. If deviated greatly from the right adjustment point, panel will light white. VH (voltage for scan IC) Adjustment Adjust so that the voltage between K2716 (VH) and K2720 (PSUS) becomes 103V 0.5V. PSUS (=GNDH) is a floating GND and the electric potential is different from that of chassis GND. Be sure not to short-circuit PSUS (=GNDH) and another GND, because that may damage the unit. The symptom is case of mis-adjustment If the VH adjustment is not performed properly, dots like blinking luminance points appear. If deviated greatly from the right adjustment point, panel will light white.
IC5V Adjustment Adjust so that the voltage between K2707 (IC5V) and K2720 (PSUS) becomes 5.0V 0.1V. PSUS (=GNDH) is a floating GND and the electric potential is different from that of chassis GND. Be sure not to short-circuit PSUS (=GNDH) and another GND, because that may damage the unit.
64
PDP-433PE, PDP-433PU
Adjusting Point
Adjusting Method
X-SUS-B, Y-SUS-B Adjustment Set to the indicated value with the remote control unit. (Refer to "Timing adjustment of control signal of X and Y Drive Assys".)
REF_DIG mode in Factory mode White 100% XSUSB ADJ YSUSB ADJ
Adjusting Point
Adjusting Method
White 100%
VRN (minus reset voltage adjustment) Adjust so that the voltage between K3707 (VRN) and K3702 (SUS-GND) becomes -280V 1.0V.
Adjusting Point
Adjusting Method
Adjust the parameter in the OFFSET-DIGITAL of factory mode as follows; PANEL R-HIGH PANEL B-LOW In this time, dispay uses the mask (MASK04) of factory mode. Reference : Adjustment values using the Media color-difference meter (A-100) MASK Left Side x y 294 303 MASK Right Side 293 294
When perform the various adjustment by RS-232C control, execute a "DM0" command (release the limit of pulse number)
beforehand. After the adjustment completion, execute a "DM 3" command (Limit of pulse number: 64%, shipping state) by all means.
65
PDP-433PE, PDP-433PU
Adjustment VR X DRIVE SUS-U VR3203 SUS-D VR3202 SUS-B VR3201 SUS-G VR3200
Test pin for adjustment and measurment Pulse Module X DRIVE Upper Lower SUSOUT K3105 K3106 SUS-U K3200 K3204 SUS-D K3108 K3205
Adjustment Procedure
Power ON Black Mask Screen
Display a SUSOUT waveform Coarse adjustment of SUS-U, SUS-B, SUS-G Display a SUS-D waveform SUS-D adjustment Adjust the waveform to 20-25ns. Display a SUS-U waveform SUS-U adjustment Adjust the waveform to 20-25ns. Power OFF Adjust VR resistance value of SUS-B and SUS-G to match VR resistance value of SUS-D within 2. Power ON and display a SUS-D waveform SUS-D readjustment Adjust the waveform to 20-25ns. Display a SUS-U waveform SUS-U readjustment Adjust the waveform to 20-25ns. Power OFF Adjust VR resistance value of SUS-B and SUS-G to match VR resistance value of SUS-D within 2. Power ON and display a SUSOUT waveform
Compare waveform, and do harmonize almost? Yes Adjustment end As for this adjustment, adjustment with set state is difficult. Therefore replace it every Assy when replacing the pulse module.
No
66
PDP-433PE, PDP-433PU
5s/div
CH1 : Y SUSOUT Under (K2203), 50V/div CH2 : Y SUSOUT Upper (K2212), 50V/div CH4 : YPR-U1 (K2038)- Trigger, 5V/div Trigger : 2msec delay Use this sustain pulse and adjust.
5s/div
CH1 : X SUSOUT Under (K3106), 50V/div CH2 : X SUSOUT Upper (K3105), 50V/div CH4 : YPR-U1 (K2038)- Trigger, 5V/div Trigger : 2msec delay Use this sustain pulse and adjust.
Perform adjustment of waveform with a black mask screen. It is easy to adjust when turned field AB offset to OFF (RS-232C command: OCN) in adjustment. Note: Sampling rate of oscilloscope sets it more than 500MS/s in order to perform ns order adjustment. Collecting calibration of probe before adjustment by all means. Connect GND of probe measuring waveform to SUSGND terminal by all means. Precise waveform is not displayed, and an adjustment gap may occur that does not collect GND properly.
When took waveform be each drive Assy unit, measure it at the fourth sustain pulse from the back except for a large width sustain pulse. Therefore, when measured both waveform of the X and Y drives together, it becomes the sustain pulse of 8 and 9 pulses from the back.
Adjust with SUS-B CH1 : Y SUSOUT Under (K2203), 50V/div CH2 : Y SUSOUT Upper (K2212), 50V/div CH4 : YPR-U1 (K2038)- Trigger, 5V/div Trigger : 2msec delay Adjust with SUS-G
500ns/div
67
PDP-433PE, PDP-433PU
5s/div
5s/div
Magnification
Magnification
500ns/div
200ns/div
Magnification
Magnification
CH1 : Y SUS-D Under (K2225), 50V/div CH2 : Y SUS-D Upper (K2207), 50V/div CH4 : YPR-U1 (K2038)- Trigger, 5V/div Trigger : 2msec delay
CH1 : Y SUS-U Under (K2224), 50V/div CH2 : Y SUS-U Upper (K2220), 50V/div CH4 : YPR-U1 (K2038)- Trigger, 5V/div Trigger : 2msec delay
Confirm it to waveform of CH1 / CH2 of the part which enclosed in the following circle whether there is not a large gap. (A gap of the quantity that shifts 20nS and adjusted remains.) When adjust in the power supply ON state, change so that the quantity of gap that adjusted by temperature-rise of the pulse module becomes small. Therefore, perform high power OFF (RS-232C command: DRF) except measurement time of waveform when adjusts, and adjustment error by temperature-rise does not occur.
500ns/div
CH1 : Y SUSOUT Under (K2203), 50V/div CH2 : Y SUSOUT Upper (K2212), 50V/div CH4 : YPR-U1 (K2038)- Trigger, 5V/div Trigger : 2msec delay
68
PDP-433PE, PDP-433PU
5s/div
CH1 : Y SUSOUT (K2203), 50V/div CH2 : X SUSOUT (K3106), 50V/div CH4 : YPR-U1 (K2038)- Trigger, 5V/div Trigger : 2msec delay Measure a waveform of this section and adjust.
Magnify the fourth pulse sustain pulse (XSUSOUT waveform) from the back of the above waveform.
O K
G N
100nsec/div
100nsec/div
140V Line
140V Line
GND 50V/div This broken section moves by changing the adjustment parameter. Become less than 140V. NG 50V/div
69
PDP-433PE, PDP-433PU
Y DRIVE Assy
K2218 (1/2 VSUS) K2716 (VH) K2215 K2217 (SUS_B) (SUS_U) K2214 (SUS_G) K2216 (SUS_D) K2720 (PSUS) K2717 (VH CONT)
X DRIVE Assy
K3214 (SUSGND) K3213 (1/2VSUS) K3707 (VRN) K3702 (SUS. GND) K3708 (VRN_OVP) K3706 (X DC-DC PD)
K2227 (SUS_D) K2715 (YDC_DC_PD) K2718 (VH UVP) VR2703 (VH_ADJ) K2212 (SUSOUTB) K2719 (VH OVP) K2708 (VOFS) K2705 (SUSGND)
K3205 (SUS_D)
K2226 (SUS_U)
K3204 (SUS_U)
K2222
K3106 (SUSOUT_B)
K2709
K2712 (VOFSUVP)
K2011 K2010 K2013 K2009 K2005 K2003 K2002 K2001 K2004 K2205
K2221 (+15V)
K2225 (SUS_D)
K2021 K2008 (YPR_U2) K2012 (DGND) (PN MUTE) K2053 (SOFT_D) K2041 (OFS) K2040 K2038 (YCP_MSK) (YPR_U1) K2039 (YSUS_MSK) K2007 K2037 (YSUS_G) K2029 (DGND) K2028 (YSUS_U) (YSUS_D) K2006 K2024 (+5V) VR2204 K2027 (DGND) (SUS_U_ADJ) (YSUS_B) VR2203 K2101 (SUS_D_ADJ) (DEW_DET) VR2202 (SUS_B_ADJ) VR2201 (SUS_G_ADJ) K2707 (IC5V)
K3021 K3007 K3010 (XNR-U) K3022 K3025 K3015 K3017 (XSUS-MSK) (XCP-MSK) K3014 (XNR-D1) K3012 (XSUS-D) K3203 (1/2VSUS) K3018 (XNR-D2) K3013 (XSUS-G) K3004 (XSUS-U) K3003 K3001 (XSUS-B) (+5V) K3103 (VCP_PD) VR3203 (SUS-U) VR3202 (SUS-D) VR3201 (SUS-B) VR3200 (SUS-G) K3104 (+5V)
K3108 (SUS_D)
K2224 (SUS_U)
K2704 (VF-)
K3200 (SUS_U) K2714 (GNDHS) K2706 (+14V) K2711 (-8V) K3105 (SUSOUTA)
K2203 (SUSOUTA)
K2701 (VF+)
Adjusting Points
70
PDP-433PE, PDP-433PU
6.4 COMMAND
6.4.1 RS-232C Command
As for PDP-433P system, the 232C control of the panel control item is possible by a single state. However, the following exclusive use communication jig is necessary.
Be careful so that can not use a DSUB 9-pin in the rear panel of the media receiver.
Connection
PDP rear view
DVI (Video line): Input optional video from the signal source with the DVI output. Input timing is as follows. DVI input timing XGA60 (VESA conformity)
CLK
H total H disp H sync H BP V total V disp V sync V BP fH fV
65MHz
1344 clk 1024 clk 136 clk 160 clk 806 line 768 line 6 line 29 line 48.363 kHz 60.004 Hz PC for control Connect to DSUB 9-pin
Communication baudrate
38400 bps is fixed.
71
R2
C1
1 C1+ 2 V+ 3 C1DOUT1 14 RIN1 13 GND 15 VCC 16
SP_L
PDP-433PE, PDP-433PU
R4 1/50 R7 100 C2
4 C2+ 5 C26 V7 DOUT2 8 RIN2
ROUT2 9 DIN2 10 DIN1 11 ROUT1 12
100
1/50
R5 1/50 0
C3
100
R8
100
SMPOW SP_R
13 12 11 3 2 1
CN2 AKB1099
C4
0.1
GND
10k 1/50 100k 100k 10k
G_JIGU10
C5
47/16
R12
2.2k
R13 0
R14
R15
R16
CN5 B3B-PH-SM3-TBB
G_JIGU10 IC2 PQ05DZ51-TLB
VIN NC VO
9V
NC
D1 D1FS4-TRB
GND
GND VC
D2 D1FS4-TRB
0.1
0.1
R17
CN4 AKP1205
C6
9.3V
C7
47/16
C8
C9
C10
47/16
G_JIGU10
R3
72
V_JIGU10 R1 1k
PDP-433PE, PDP-433PU
RS-232C Command
Command AB0 AB1 AB2 AB3 ABL AMN AMY DRF DRN DW0 DWF DWn EWN EWY F50 F60 F61 F70 GAJ GPW GS1 HMS M00 M01 M02 M03 M04 M05 M06 M07 M08 M09 M10 M11 M12 M13 M14 M51 M52 M53 M54 M55 M56 M57 M58 M59 M60 M61 M62 M63 M64 M65 M66 M67 M68 M69 M70 Name ABL REFERENCE MODE ABL OFFSET MODE 1 ABL OFFSET MODE 2 ABL OFFSET MODE 3 ABL ADJUST AUDIO MUTE OFF AUDIO MUTE ON DRIVE OFF DRIVE ON DOWN 0 DOWN FULL DOWN n EEPROM WRITE NO EEPROM WRITE YES FREE RUN 50VIDEO FREE RUN 60VIDEO FREE RUN 60PC FREE RUN 70PC GET ADJUST GET PANEL W/B GET STATUS 1 HOUR METER SET MASK 00 MASK 01 MASK 02 MASK 03 MASK 04 MASK 05 MASK 06 MASK 07 MASK 08 MASK 09 MASK 10 MASK 11 MASK 12 MASK 13 MASK 14 MASK 51 MASK 52 MASK 53 MASK 54 MASK 55 MASK 56 MASK 57 MASK 58 MASK 59 MASK 60 MASK 61 MASK 62 MASK 63 MASK 64 MASK 65 MASK 66 MASK 67 MASK 68 MASK 69 MASK 70 Function Set the ABL to reference value Set the ABL to offset value 1 Set the ABL to offset value 2 Set the ABL to offset value 3 Adjustment of electric power upper limit Mute off request of speaker volume Mute request of speaker volume Drive OFF Drive ON Down the adjustment value with 10 Minimize the adjustment value Down the adjustment value with n Complete the plug & play EEPROM writing mode Start the plug & play EEPROM writing mode Display the mask screen with 50Hz (video) sequence Display the mask screen with 60Hz (video) sequence Display the mask screen with 60Hz (PC) sequence Display the mask screen with 70Hz (PC) sequence Acquire the various adjustment value of the display Acquire the W/B adjustment value of the panel Acquire the version information Set hour meter to optional time Mask mode OFF Pattern 1 (Lamp) Pattern 2 (Color bar) Pattern 3 (Slanting line) Pattern 4 (W/B measurement) Pattern 5 (W/B adjustment) Pattern 6 (W/B peak measurement) Pattern 7 (Peak measurement) Pattern 8 (Reservation) Pattern 9 (SCAN IC protection test) Pattern 10 (SCAN IC protection test) Pattern 11 (reservation) Pattern 12 (reservation) Pattern 13 (reservation) Pattern 14 (reservation) Full mask (white) Full mask (cyan 274) Full mask (magenta 1023) Full mask (flesh color) Full mask (cyan 1023) Full mask (light purple) Full mask (sky blue) Full mask (red) Full mask (green) Full mask (blue) Full mask (black) Full mask (red 779) Full mask (cyan 218) Full mask (cyan 444) Full mask (flesh color 43) Full mask (red 620) Full mask (magenta 98) Full mask (sky blue 1_43) Full mask (sky blue 2_43) Full mask (light purple 43) Direct Validity UP/DOWN Validity Lower Limit Upper Limit
000
255
73
PDP-433PE, PDP-433PU
Command M71 M72 M73 M74 MMN MMX MMY MMZ MTN MTY NMN NMY PBH PBL PGH PGL PHN PHY PLN PLY PMS POF PON PRH PRL PCN PCY PT0 PT1 PT2 UP0 UPF UPn VOF VOL VSU XSB XSG YSB YSG
Name MASK 71 MASK 72 MASK 73 MASK 74 MIRROR MODE NO MIRROR MODE X MIRROR MODE Y MIRROR MODE XY PANEL MUTE NO PANEL MUTE YES NEGATIVE MODE NO NEGATIVE MODE YES PANEL BLUE HIGH PANEL BLUE LOW PANEL GREEN HIGH PANEL GREEN LOW PANEL HIGHT-LIGHT NO PANEL HIGHT-LIGHT YES BRIGHT ENHANCE NO BRIGHT ENHANCE YES PULSE METER SET POWER OFF POWER ON PANEL RED HIGH PANEL RED LOW PC MODE NO PC MODE YES PANEL COLOR TEMP 0 PANEL COLOR TEMP 1 PANEL COLOR TEMP 2 UP 0 UP FULL UP n VOFFSET ADJUST VOLUME VSUS ADJUST XSUS B XSUS G YSUS B YSUS G
Function Full mask (yellow) Full mask (blue 916) Full mask (reservation) Full mask (reservation) Mirror mode OFF (normal display) Right and left reversing display Top and bottom reversing display Top and bottom right and left reversing display Release panel mute Panel mute Negative positive inversion mode OFF Negative positive inversion mode ON BLUE HIGH LIGHT adjustment BLUE LOW LIGHT adjustment GREEN HIGH LIGHT adjustment GREEN LOW LIGHT adjustment Release the W/B highlight maximum mode of the panel Set the W/B highlight of the panel to maximum Center brightness correction enhance OFF Center brightness correction enhance ON Optional setting of the pulse meter Standby request Power ON request RED HIGH LIGHT adjustment RED LOW LIGHT adjustment At the 60Hz input: VIDEO sequence selection At the 60Hz input: PC sequence selection Set each temperature mode to 0 (REF) Set each temperature mode to 1 (OFS1) Set each temperature mode to 2 (OFS2) Maximize the adjustment value Maximize the adjustment value Rise the adjustment value with n Vofs adjustment Volume Vsus adjustment X-SUS-B pulse adjustment X-SUS-G pulse adjustment Y-SUS-B pulse adjustment Y-SUS-G pulse adjustment
Direct Validity
UP/DOWN Validity
Lower Limit
Upper Limit
000 000
255 999
74
PDP-433PE, PDP-433PU
Function
Output data of an electronic VR adjustment value and a drive system adjustment value Output data to be related to white balance adjustment of the panel Output data such as version information, hour meter and pulse meter
GAJ: Output data of an electron VR adjustment value and a drive system adjustment value
Output it according to transmission order and size of the table below.
Order
1 2 3 4 5 6 7 8 9
Data Contents
Setting mode of electric power upper limit value Electric power upper limit value (Offset data) (ABL) Vsus adjustment value (Reference data) Vofs adjustment value V-SUS-B adjustment value V-SUS-G adjustment value Y-SUS-B adjustment value Y-SUS-G adjustment value (Reference data) (Reference data) (Reference data) (Reference data) (Reference data) (Reference data)
Size
3 byte 3 byte 3 byte 3 byte 3 byte 3 byte 3 byte 3 byte 3 byte (Note 1)
Remarks
AB* ( *: 0 to 3)
(Note 1) : When performed in reference mode selection, offset data outputs the same value as the reference data. (Note 2) : Checksum of 2 bytes is added at the end, but ignore it.
GPW (Get Panel White balance): Output data to be related to white balance adjustment of panel
Output it according to transmission order and size of the table below.
Order
1 2 3 4 5 6 7 8 9 10 11 12
Data Contents
Panel color temperature mode (Reference data) Gain of W/B adjustment value (Offset data) Red (Reference data) Gain of W/B adjustment value (Offset data) Green (Reference data) Gain of W/B adjustment value (Offset data) Blue Offset of W/B adjustment value (Offset data) Red (Reference data) Offset of W/B adjustment value (Offset data) Green (Reference data) (Reference data)
Size
3 byte 3 byte 3 byte 3 byte 3 byte 3 byte 3 byte 3 byte 3 byte 3 byte 3 byte 3 byte (Note 1) (Note 1) (Note 1) (Note 1) (Note 1)
Remarks
PT* ( *: 0 to 3)
Offset of W/B adjustment value (Offset data) 3 byte (Note 1) Blue (Note 1) : When performed in reference mode selection, offset data outputs the same value as the reference data. (Note 2) : Checksum of 2 bytes is added at the end, but ignore it. 13
75
PDP-433PE, PDP-433PU
GS1: Output data such as version information, hour meter and pulse meter
Output it according to transmission order and size of the table below.
Order
1 2 3 4 5 6 7 8 9 10 11
Data Contents
Display information Module microcomputer model number Module microcomputer version Panel microcomputer version Panel /FLASH ROM version Hour meter (hour) Pulse meter Main microcomputer model number Main microcomputer version Wide microcomputer version Wide /FLASH ROM version
Size
3 byte 4 byte 3 byte 3 byte 3 byte 5 byte 7 byte 4 byte 3 byte 3 byte 3 byte Unit: H (time) See below 5691 or F691
Remarks
Display Information
Data
MX5 MX4 MD5 MD4 HD5 HD4 PDP-433MX Module 50 inches Module 43 inches PDP-503HD PDP-433HD
Model
PDP-503MX (initial value)
76
PDP-433PE, PDP-433PU
7. GENERAL INFORMATION
7.1 DIAGNOSIS
7.1.1 PCB LOCATION
CLAMP A Assy ADR CONNECT A Assy BRIDGE A Assy THERMAL SENSOR Assy ADR CONNECT B Assy SUB ADDRESS A Assy ADR RESONANCE Assy ADR CONNECT C Assy BRIDGE B Assy
DIGITAL VIDEO Assy ADR CONNECT D Assy SCAN (B) Assy CLAMP B Assy
IR (P) Assy CLAMP A Assy X CONNECTOR (A) Assy X DRIVE Assy FRONT KEY CONN Assy FRONT KEY Assy ADR CONNECT D Assy AUDIO AMP Assy SP TERMINAL Assy BRIDGE C Assy MR INTERFACE Assy ADR RESONANCE Assy SUB ADDRESS B Assy ADR CONNECT B Assy BRIDGE D Assy ADR CONNECT A Assy LED Assy X CONNECTOR (B) Assy
CLAMP B Assy
Rear View
77
PDP-433PE, PDP-433PU
Shut Down
Operations : When a microcomputer detected abnormality, turn the power supply to OFF. LED display : Green blinks Examples: LED blinks in the DIGITAL-IIC communication NG
Green LED lights for 200 msec. Lights out for 100 msec Green LED lights for 200 msec.
Number of blinks
1 2 3 4
Name
Panel Microcomputer NG DIGITAL-IIC communication NG Dewdrop abnormality Temperature abnormality
Power Down
Operations : When this unit becomes the dangerous state, turn the power supply OFF with the protection circuit. LED display : Red blinks * When protection circuit more than two places almost worked simultaneously, display LED in order to 1st - 2nd. Examples: LED blinks in the 1st power down = Y-DC/DC CONVERTER, 2nd power down = Y-DRIVE
1st power-down information Red LED lights for 200 msec. Lights out for 100 msec Red LED lights for 200 msec. Lights out for 1 sec 2nd power-down information Red LED lights for 200 msec.
Number of blinks
1 2 3 4 5 6 7 8
Name
Y-DRIVE Y-DC/DC CONVERTER X-DC/DC CONVERTER X-DRIVE Power supply Address junction Address resonance DIGITAL-DC/DC CONVERTER
78
PDP-433PE, PDP-433PU
DDC_SCL DDC_SDA
D18
2
IC1207 Module UCOM
TEMP1 4
Y DRIVE ASSY
D6 IC1204 EEPROM Y2 CN2002 Moisture Sensor
D3
DEW_DET 3
2
A_SCL A_SDA SCL SDA
D1
P2
MR INTERFACE ASSY
R3
AUDIO ASSY
IC5202 CXA2021S
MEDIA RECEIVER
Note: 1 - 4 show LED flashing number of times when shut down occurred in this route.
79
PDP-433PE, PDP-433PU
E06
2 DIGITAL-IIC communication NG
When a module microcomputer failed in communication with outside EEPROM or EXPANDER, this NG occurs. Shut down after OSD display for 30 seconds from the NG detection. * However, this communication NG may occur in the standby state. Abnormality to expect Open / Short of communication line in the DIGITAL VIDEO, MR INTERFACE and AUDIO Assys Breaking of wire of the following points is thought about. DIGITAL VIDEO Assy (D1) SW POWER SUPPLY Module (P2) DIGITAL VIDEO Assy (D3) MR INTERFACE Assy (R3) MR INTERFACE Assy (R23) AUDIO Assy (A24) System Cable
E06
4 Temperature abnormality
When temperature of this unit became abnormally high, this NG occurs. Shut down after OSD display from the NG detection for 30 seconds. Note: When temperature fell down during indication, return to the normal operation. Abnormality to expect when it occurs in the environment that is not high-temperature Disconnect a connector between DIGITAL VIDEO Assy (D18) and temperature sensor 1 (TE1).
E04
Reference
Shut down temperature of each temperature sensor Sensor Temp 78
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
1 / 13 CENTER Ve r s i on OSD Ve r s i on CV I C Ve r s i on TTXP Ve r s i on MON I TOR Ve r s i on PANEL Ve r s i on FLASH Ve r s i on MON I TOR Mode l Mod e l S e l e c t Ma i n Mod e l S e l e c t AV Mod e l S e l e c t MON I TOR Sen so r e Temp Cen t e r A cu t ime RESET Mon i t o r Ac u t i me RESET Pu l s e Ac u t i me RESET I NPUT 1 No S I G MR MA I N E 2 0 0 1 / 0 9 / 2 5 H MR OSD 2 0 0 1 / 0 9 / 1 0 A W2 0 0 1 / 0 9 / 1 2 0 9 : 0 0 X2 0 0 1 / 0 9 / 1 2 0 9 : 0 7 V2 0 0 1 / 0 9 / 1 2 0 9 : 1 0 TTX PRG 061 F6 9 1 1 0 - 00 - 05 01 0 4 0 +28 16 H 41 M OFF 47 H 42 M OFF 164 OFF
80
X DRIVE ASSY
DIGITAL DC-DC
D8 - D11
IC1201-pin 8
4 P4
OR OR
D12 - D15
PD Circuit
OR
Relay Circuit
OR
IC1201-pin 6
1 2 P3
D16
OR
PD_TRIGGER
Y1
D17
Y DRIVE ASSY
PDP-433PE, PDP-433PU
Note: 1 - 8 show LED flashing number of times when power down occurred in this route.
81
PDP-433PE, PDP-433PU
Function
Remarks
Y DRIVE Assy
P.D. by VOFS undervoltage (= overcurrent) P.D. by VH overvoltage P.D. by VH undervoltage (= overcurrent) P.D. by IC5V undervoltage (= overcurrent) P.D. by VRN overvoltage P.D. by VRN undervoltage (= overcurrent) P.D. by VCP overcurrent P.D. by reset circuit overcurrent P.D. by VSUS overvoltage P.D. by VSUS undervoltage (= overcurrent) P.D. by VADR overvoltage P.D. by VADR undervoltage (= overcurrent) P.D. by 15V overvoltage P.D. by 15V undervoltage (= overcurrent) P.D. by 12V undervoltage (= overcurrent) P.D. by 6.5V overvoltage P.D. by 6.5V undervoltage (= overcurrent) P.D. by 13.5V undervoltage (= overcurrent) P.D. by -9V undervoltage (= overcurrent) P.D. by +B overvoltage P.D. by +B overcurrent P.D. by AC200V apply PFC module overheat protection VSUS arc resistance overheat protection Note 1
VH OVP VH UVP IC5V UVP VRN OVP VRN UVP VCP OCP RESET OCP VSUS OVP VSUS UVP VADR OVP VADR UVP 15V OVP 15V UVP 12V UVP
3 X DRIVE Assy 4
6.5V OVP 6.5V UVP 13.5V UVP -9V UVP +B OVP +B OCP AC200V P.D.
6 7
ADR.PD ADR.K.PD 5.0V OVP 5.0V UVP 3.3V OVP 3.3V UVP 2.5V OVP 2.5V UVP
P.D. by disconnecting the connector P.D. by ICP open and TCP defective P.D. by 5V overvoltage P.D. by 5V undervoltage (= overcurrent) P.D. by 3.3V overvoltage P.D. by 3.3V undervoltage (= overcurrent) P.D. by 2.5V overvoltage P.D. by 2.5V undervoltage (= overcurrent)
Reference OVP : Over Voltage Protect UVP : Under Voltage Protect OCP : Over Current Protect Note 1: AC200V P.D. is not applicable to the PDP-433PE and PDP-433PU models.
82
Diagnosis of the error point in the various protection circuit (P.D. circuit) operation (Red LED blinks)
Error Pont Possible Part of Error Circuit State Diagnosis Condition
K2211 Lo VCP OCP VOFS OVP Drive section (control signal, output elements etc.) in normal operation VOFS D/D CONV. BLOCK in normal operation K2719 Lo VH OVP Drive section (control signal, output elements etc.) in normal operation K2718 Lo VH UVP VH D/D CONV. BLOCK in normal operation SCAN Assy in normal operation IC5V D/D CONV. BLOCK in normal operation K2713 Lo IC2704, IC2706, IC2717 IC3702, IC3712 K3708 Lo IC3701, IC3702, IC3712 K3705 Lo Q3122 IC3200, IC3201 (pulse module), IC3103, IC3104, IC3106, IC3107, IC3110, IC3113, R3109 Q3122 IC3200, IC3201 (Pulse module) IC2206, IC2214 (Pulse module) IC8601 (Audio IC) K3103 Lo K3102 Lo VCP OCP VRN OCP When P4 connector disconnected, P.D. does not occur When P3 connector disconnected, P.D. does not occur When P6 connector disconnected, P.D. does not occur When pin 5 of P2 connector disconnected, P.D. does not occur SW POWER SUPPLY Module Disconnect D8 - D15 connectors TCP damage of IC6704 (ICP), disconnect D16 and D17 connectors, panel microcomputer is defective, outside Flash ROM of the panel microcomputer is defective. K1901 Lo K1902 Lo K1903 Lo K1904 Lo K1905 Lo K1906 Lo ADR. PD ADR. K. PD When the voltage is not output even if P4, P3 and P6 connectors disconnected VRN UVP VRN OVP Drive section (control signal, output elements etc.) in normal operation VRN D/D CONV. BLOCK in normal operation IC5V UVP SCAN Assy in normal operation K2712 Lo IC2206, IC2214 (Pulse module), IC2203, IC2204, IC2212, IC2213, IC2213, IC2217, R2209 IC2702, IC2709, IC2715 IC2701, IC2702, IC2709, IC2715 K2709 Lo VOFS UVP Q2211, Q2212, R2277, IC2208, IC2210 IC2712, IC2716 IC2711, IC2712, IC2716 SCAN IC IC2704, IC2706, IC2717 SCAN IC
Y DRIVE
Y DRIVE Assy
Y DC DC
X DC DC
X DRIVE Assy
X DRIVE
X DRIVE Assy
X DRIVE Assy
Y DRIVE Assy
MX AUDIO Assy
PS
ADDRESS CONNECT A - D Assy, RESONANCE Assy, D/D CONV. BLOCK (DIGITAL VIDEO Assy)
ADR
ADR K
RESONANCE Assy
5.0V OVP 5.0V UVP 3.3V OVP 3.3V UVP 2.5V OVP 2.5V UVP
DIGITAL DC DC
Note: About PS PD The condition that Red LED blinks five times (power supply PD) 1 When the internal protection circuit of SW POWER SUPPLY Module worked 2 When a microcomputer was not able to identify the PD point Being careful because the protection circuit of SW POWER SUPPLY Module cannot conclude that worked.
PDP-433PE, PDP-433PU
83
PDP-433PE, PDP-433PU
IC5V VF12V
STB5V
13.5V -9V
X DRIVE ASSY
VRN DC/DC Converter VRN -280V
12V
Supplementary information
1. Power on/off switch for the large-signal system (SW102) Function: Only the power for the small-signal system (15V, 12V, 6.5V, 13.5V, and -9V) is on, and the power for the large-signal system (VSUS, VADR) is off. Usage: Use when only an operational check for the smallsignal system is required. Supplementary information: When this switch is to be used, the wires of pin 5 (DIG, ADR, and PD) of the P2 connector of the power-supply module should be disconnected to prevent the PD circuit from operating. To turn the power of the large-signal system off without using this switch, operation from an external PC through RS-232C commands "DRF" is basically required. In this case, the above procedure is not required, as the PD circuit is muted by software. 3. Temperature compensation of the VSUS voltage for the drive system Function: Control the power supply voltage mentioned above according to temperature. (Temperature compensation works so that the voltage is lowered on the lowertemperature side, and is raised on the highertemperature side.) Purpose: To improve the yield by compensating the temperature characteristics of the panel. Supplementary information: For this model, temperature compensation is performed only for the VSUS voltage, and not for the VOFS voltage, and it is controlled by software. 4. When a fuse blows If a fuse blows, never turn the power on again only after replacing the fuse. (In most cases, the fuse itself did not have any problem. So as long as factors of overcurrent have not been removed, chances of destruction increase every time the power is turned on. In the worst case, about a dozen parts may be destroyed.) Principally, the whole power-supply module must be replaced. 5. Voltage adjustment of the panel drive As this model employs the electronic VR system for the VSUS and VOFS voltages, and as the voltage-adjustment data are stored in the DIGITAL assembly, voltage adjustment of the panel drive is not necessary when the power-supply modules are changed. (For VADR, VH, and VRN, adjustments with semifixed VR controls are necessary.) For this model, as the power-supply block has been developed and designed by an outside vendor, at the point you know which module is a cause of failure (through diagnosis described elsewhere in this manual), change the corresponding modules, and do not diagnose or repair the module. Similarly, the switches and the semifixed VRs inside the powersupply module must not be adjusted without a special reason.
Method of power supply ON in the large signal system OFF state with RS-232C command
1 Confirm that this unit is the standby state. 2 Transmit RS-232C command "DRF." 3 Turn the power supply ON by remote control unit, side key or command "PON." When turn the power supply OFF once, return to setting of large signal system ON. When turn the power supply ON in the large signal system OFF, transmit "DRF" command each time. 2. 200V AC power-down switch (SW101) Function: While 200V AC voltage is applied, operation of the PD circuit is turned on and off (ON when the switch is set to 100V AC, and OFF when the switch is set to 200V AC). Setting: For the PU model only, the switch is set to 100V, and for other models, it is set to 200V.
84
PDP-433PE, PDP-433PU
7.1.3 DISASSEMBLY
About detect switch
This unit adopt the "Rear Case opened ! detection" system. Please work in service as follows by all means. Outline and caution Perform video transmission from the media receiver to the plasma display with digital signal in the PDP-433HD series. Therefore adopt contents protection by HDCP for copyright protection. Moreover establish the detect switch which is never turned on the power when "a rear case of plasma display was opened carelessly". Detect switch does not detect at the power supply OFF and the remote control unit wait state. Please stick this detect switch with tape before turning on the power in inside diagnoses of the plasma display. And please remove it not to forget the tape which stuck after the repair.
1 1 1 1 1 1 1
2 3 4
Remove the IF Earth Metal.(Screws 2) Remove four screws. Remove the SW Power Supply Module.
3
Rear View
4
When detect switch has worked by any chance When detect switch works, LED of red blinks in succession by a 300msec period. Press keys in order of "MENU" key, "ENTER" key and "POWER" key with the remote control unit after sticking the detect switch with tape or close the rear case beforehand. This unit activates and it becomes the service factory mode screen. Afterwards, turn off the power with the remote control unit. Perform the normal operation afterward.
3 2
IF Earth Metal
85
PDP-433PE, PDP-433PU
Insert the SW Power Supply Module into the slit of Sub Frame L and R.
1 2 3 4 5 6
Remove the Rear Case (P). (Screws 19) Remove the SW Power Supply Module. (Connector, Screws 4) Remove the IF Earth Metal (Screws 2) Remove the MR INTERFACE Assy (Connector, Screws 4) Remove the SP TERMINAL Assy (Connector, Screws 2) Remove the AUDIO AMP Assy (Connector, Screws 2) IF Earth Metal MR INTERFACE Assy AUDIO AMP Assy
Slit
5
SW Power Supply Module Sub Frame L Sub Frame R
4 5
6
SP TERMINAL Assy
6 4
4
5
SW Power Supply Module
Diagnosis
7
DIGITAL VIDEO Assy
86
PDP-433PE, PDP-433PU
7 8 9
Remove the Rear Case (P). (Screws 19) Remove the Y DRIVE Assy. (Connector, PCB Spacer 3, Screws 8) Remove the Front Chassis V. (Screws 5) (Screws 1)
8 1
3
8 8
2 3 4
Loosen a rivet. Remove the Lead Cover (P). Pull out a Flexible Cable.
10
9 2
Lead Cover (P) Rivet 3 Turn it not to press the rivet. Lead Cover (P) (Because when the rivet presses, fit in once again.) It is easy to remove when pull out the Lead Cover (P) with the rivet before completely removing the rivet.
11 Reverse the SCAN (A) and SCAN (B) Assemblies. 12 When it is necessary, exchange the ROM.
5 6
Remove bottom by the fulcrum at the top of Front Case Assy 43 (P). Remove the Front Case Assy 43 (P).
11
Rear Case
6
Aluminum Materials It is the structure that a hook of Front Case Assy 43 (P) was put between with Rear Case and aluminum materials.
11
ROM 6
87
PDP-433PE, PDP-433PU
X DRIVE Assy
1 2
Remove the Rear Case (P). (Screws 19) Remove the X DRIVE Assy. (Connector, PCB Spacer 3, Screws 8)
X DRIVE Assy
2
2
88
PDP-433PE, PDP-433PU
7.2 IC INFORMATION
The information shown in the list is basic information and may not correspond exactly to that shown in the schematic diagrams.
List of IC
SN755860PJ, HD64F2328VF, PE1013B, M30624FGAFP, PD6358A, PST9246N, FS781BZB, STK795-460
SN755860PJ (SCAN B ASSY : IC6201 - IC6206) SN755860PJ (SCAN A ASSY : IC6001 - IC6006)
Scan IC
90 HVO35 HVO36 HVO37 HVO38 HVO39 HVO40 HVO41 HVO42 HVO43 HVO44 HVO45 HVO46 HVO47 HVO48 HVO49 HVO50 HVO51 HVO52 HVO53 HVO54 HVO55 HVO56 HVO57 HVO58 HVO59 HVO60 HVO61 HVO62 HVO63 HVO64 1 80 HVO30 HVO29 HVO28 HVO27 HVO26 HVO25 HVO24 HVO23 HVO22 HVO21 HVO20 HVO19 HVO18 HVO17 HVO16 HVO15 HVO14 HVO13 HVO12 HVO11 HVO10 HVO9 HVO8 HVO7 HVO6 HVO5 HVO4 HVO3 HVO2 HVO1
10 70
20 60
30 40 50
VH2 VH2 NC GND GND A/B DB GND VLK LE VDD OC1 OC2 DA CLR GND GND NC VH1 VH1
89
PDP-433PE, PDP-433PU
Block Diagram
DB A/B CLR DA CLK LE
64 bit Latch
DATA DATA
GND
OC1 OC2
Selector VDD
Selector
GND HVO33 - 64
VH2
GND HVO1 - 32
VH1
Pin Function
Name
CLK DA DB LE A/B CLR OC1 OC2 HVO VDD GND VH1 VH2 NC 39 44 37 40 36 45 42 43 1-30, 51-82, 99, 100 41 34, 35, 38, 46, 47, 87-89, 91-94 84, 85, 49, 50 31, 32, 96, 97 33, 48, 95, 83, 86, 90, 98
Pin No.
I/O
I I/O I/O I I I I I O
Num.
1 1 1 1 1 1 1 1 64 1 12 4 4 7
Function
Shift clock (start edge partial response) The serial data input of shifting register The serial data output of shifting register It output data done a latch of by "L" level A shift directional control signal of shift register It do data of shift register with "L" by "L" level An output control terminal of HVO An output control terminal of HVO High voltage drive output (HVO1 - HVO64) Logic power supply Standard potential. This is common to HVO1 - HVO64. The high potential circuit power supply which is common to HVO1 - HVO32 The high potential circuit power supply which is common to HVO33 - HVO64 It is the insulation electrically
90
PDP-433PE, PDP-433PU
HD64F2328VF (DIGITAL VIDEO ASSY : IC1101)
Panel Microcomputer Pin Function
No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
Pin Name
CS_23 NC VSS VSS VCC UA0 UA1 UA2 UA3 VSS UA4 UA5 UA6 UA7 UA8 UA9 UA10 UA11 VSS UA12 UA13 UA14 UA15 UA16 UA17 UA18 UA19 VSS UA20 PA5 PA6 PA7 CE_PN CE_PN VSS VSS APLP VD_31 VCC UD0 UD1 UD2 UD3 VSS UD4 UD5 UD6 UD7 UD8 UD9 PE5064 (IC1703) control output NC Terminal GND GND 3.3V power supply Address bus Address bus Address bus Address bus GND Address bus Address bus Address bus Address bus Address bus Address bus Address bus Address bus GND Address bus Address bus Address bus Address bus Address bus Address bus Address bus Address bus GND Address bus NC terminal NC terminal NC terminal Enables / for panel microcomputer Enables / for panel microcomputer GND GND
Function
The APL value acquisition trigger signal input The V signal input from IC1401 (PD6358) 3.3V power supply Data bus Data bus Data bus Data bus GND Data bus Data bus Data bus Data bus Data bus Data bus
91
PDP-433PE, PDP-433PU
No.
51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
Pin Name
UD10 UD11 VSS UD12 UD13 UD14 UD15 VCC D_TXD EXT_TXD D_RXD EXT_RXD D_CLK P60 VSS CS_FLASH VSS VSS P61 UDREQ P63 WE_FLASH BUSY REQ_PU SEL23B CLRB FR_SEL RST31B RST23B FWE RESET NMI STBY VCC XTAL EXTAL VSS PF7 VCC PF6 RDB HWRB PF3 PF2 PF1 PF0 P50 P51 VSS VSS Data bus Data bus GND Data bus Data bus Data bus Data bus 3.3V power supply
Function
Communication with IC1207 (module microcomputer) Communication with the outside (program notes) Communication with IC1207 (module microcomputer) Communication with the outside (program notes) Communication with IC1207 (module microcomputer) NC terminal GND A flash memory control terminal GND GND NC terminal IC1703 (PE5064) control terminal NC terminal A flash memory note control signal (unused) The command receipt of a message lye Norwich output A communication demand to a module microcomputer IC1703 (PE5064) control terminal IC1703 (PE5064) control terminal The free run select signal output The reset output to IC1301, IC1401 (PD6358) The reset output to IC1703 (PE5064) Microcomputer program note control signal Reset input The at the rate of tang input (unused) The hardware standby input (unused) 3.3V power supply A clock oscillation child connection terminal A clock oscillation child connection terminal GND NC terminal 3.3V power supply NC terminal A read control terminal from an outside slave device A wright control terminal to an outside slave device NC terminal NC terminal NC terminal NC terminal NC terminal NC terminal GND GND
92
PDP-433PE, PDP-433PU
No.
101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128
Pin Name
P52 P53 AVCC VREF STOPB P41 RYBY ADR_K_EMG_L1 ADR_K_EMG_U1 ADR_K_EMG_L2 ADR_K_EMG_U2 P47 AVSS VSS MUTE_ADR MUTE_SUS P15 HD P13 P12 PC_VIDEO VD MD0 MD1 MD2 PG0 CS_31Y CS_31X NC terminal NC terminal 3.3V power supply
Function
A/D, D/A reference voltage input (unused) The drive control input from IC1703 (PE5064) NC terminal The flash memory note ready input The emergency input from panel bottom address resonance block The emergency input from panel upper address resonance block The emergency input from panel bottom address resonance block (unused) The emergency input from panel upper address resonance block (unused) NC terminal GND GND The panel mute signal input The X and Y drive mute signal output (unused) NC terminal The HD signal input from outside Assy (RGB Assy etc.) NC terminal NC terminal The PC/Video identification output The HD signal input from outside Assy (RGB Assy etc.) The microcomputer mode of operation select signal input The microcomputer mode of operation select signal input The microcomputer mode of operation select signal input NC terminal IC1301, IC1401 (PD6358) control signal IC1301, IC1401 (PD6358) control signal
93
PDP-433PE, PDP-433PU
Block Diagram
XSUS_BI
23
1_40
XSUS_BO
XSUS_UI
22
1_39
XSUS_UO
XSUS_DI
21
1_40
XSUS_DO
XSUS_GI
19
1_54
YSUS_GO
XNR_D1I
1_44
18
1_36
XNR_D1O
XNR_D2I
10
1_43
15
1_35
XNR_D2O
XSUS_MSKI
17
1_41
XSUS_MSKO
XCP_MSKI
16
1_42
XCP_MSKO
XNR_UI
20
1_56
XNR_UO
94
PDP-433PE, PDP-433PU
Block Diagram
sus_mute_in
1_64
1_63
ysusbin
23
1_39
ysusbout
ysusuin
22
1_48
ysusuout
ysusdin
21
1_47
ysusdout
ysusgin
17
1_46
ysusgout
ypru1in
6 7
19
1_45
ypru1out
ypru2in
1_2 1_16
18
1_54 1_59
1_44
ypru2out
yofsin
1_1 1_15
20
1_66 1_33
1_43
yofsout
ysofdin
11
1_10 1_52
ysusmskin
9 10
1_51
14
1_42
ysoftdout
16
1_37
ycpmskin
1_41 1_40
ysusmskout ycpmskout
15
95
PDP-433PE, PDP-433PU
M30624FGAFP (DIGITAL VIDEO ASSY : IC1207)
Module Microcomputer
Pin Function
No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 Pin Name TXD CLK NC NC NC NC NC BYTE CNVSS XCIN XCOUT RESET XOUT VSS XIN VCC NMI REM REQ_PU /SW_TRG NC NC NC AC_OFF PD_TRIGGER NC NC NC SCL SDA TXD1 RXD1 CLK1 BUSY1 TXD0 RXD0 NC REQ_MD/A_MUTE NC NC EPM NC PU_CE NC MOD_SW/A_NG CE DITHER/SW_STC NC /SW_STP NC Function Serial 3 line data output for communication with a panel microcomputer Serial 3 line clock for communication with a panel microcomputer NC terminal NC terminal NC terminal NC terminal NC terminal The external data bus width reshuffling input (I am unused and connect GND) A power supply for program note (a note, 5V, usually, pull-down NC terminal NC terminal A reset input terminal Clock output terminal GND Clock input terminal 5V standby power Because a NMI interruption terminal is unused, It handle pull up. The SR signal input A communication demand from a panel microcomputer (the pulse meter acquisition) Main switch OFF / ON search NC terminal NC terminal NC terminal AC power OFF search and power supply ASSY differentiation. Power down search NC terminal NC terminal NC terminal EEPROM, IIC communication with power supply ASSY EEPROM, IIC communication with power supply ASSY Communication with the outside (a program note) Communication with the outside (a program note) Communication with the outside (a program note) Communication with the outside (a program note) Communication with outside ASSY (microcomputers main in RGB ASSY, etc) Communication with outside ASSY (microcomputers main in RGB ASSY, etc) NC terminal 232C communication demand (a request to a main microcomputer) / audio system mute NC terminal NC terminal The EPM input for program note (L fixation) NC terminal Enables/ for panel microcomputer NC terminal The model of machines distinction input / audio system NG input The CE input for program note (H fixation) Power supply search of a dither setting / media receiver for module NC terminal Power supply search of a panel NC terminal
96
PDP-433PE, PDP-433PU
No. 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
Pin Name NC RELAY POWER/MSTATE NC WE_PN MD0 MD2 FWE RST_PU PN_MUTE NC VCC NC VSS NC NC /A_SCL /A_SDA APD_MUTE ADR_K_PD ADR_PD DCC_PD NC NC RST2 NC /DDC_SCL /DDC_SDA NC NC DEW_DET NC NC NC NC LED_G LED_R NC BUSY NC NC /F_KEY1 MAX_PLS2/F_KEY2 TEMP1 MAX_PLS? /CCKM AVSS PM_ST VREF AVCC RXD NC terminal
Function The output for power supply ON / OFF change Input / SII861 master information for power supply ON / OFF change NC terminal Buffer state control for panel microcomputer note The panel microcomputer mode of operation change output The panel microcomputer mode of operation change output The panel microcomputer program note control signal output The panel microcomputer reset output The panel mute input NC terminal 5V standby power NC terminal GND NC terminal NC terminal IIC clock for audio system IIC data for audio system A mute signal of address series The address oscillatory system PD input The address series PD input The power supply system PD input NC terminal NC terminal Panel microcomputer reset search NC terminal IIC communication with a media receiver IIC communication with a media receiver NC terminal NC terminal The dew condensation sensor input NC terminal NC terminal NC terminal NC terminal Green LED lighting (LED on interface ASSY in a panel module) Red LED lighting (LED on interface ASSY in a panel module) NC terminal Communication permission / inhibiting signal from a panel microcomputer NC terminal NC terminal The front KEY input The terminal / front KEY input for brightness setting mode of operation change The A/D input for temperature sensor Terminal / connection search for brightness setting mode of operation change GND for AD conversion The A/D input for model of machines distinction Reference voltage for AD conversion 5V standby power for AD conversion Serial 3 line data entry for communication with a panel microcomputer
97
PDP-433PE, PDP-433PU
PD6358A (DIGITAL VIDEO ASSY : IC1301)
Pin Function
No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
Picture Improved IC
Pin Name VSS TESTO6 OSDCLK TTST VDDI OVDDE-01 AGO0 VDDI AGO2 AGO3 AGO4 VDDI ARO6 AGO7 VDDI ARO9 ABO9 VDDI ADRCLKO2 ARO12 ARO13 AGO14 AGO15 ARO16 ARO17 VSS ABO17 AGO17 AGO18 ABO19 UDAT15 UDAT12 UDAT9 UDAT5 OVDDE-06 APLP OVDDE-08 CS5BI CS4BI UADRI13 UADRI9 UADRI6 UADRI2 UADRI1 TESTI2 BIT0 OVDDE-11 TESTO4 ARO39 AGO38 GND Test output terminal (unused) The CLK input for OSD Test input terminal (unused) 2.5V power supply 3.3V power supply Address data output (G signal) 2.5V power supply Address data output (G signal) Address data output (G signal) Address data output (G signal) 2.5V power supply Address data output (R signal) Address data output (G signal) 2.5V power supply Address data output (R signal) Address data output (B signal) 2.5V power supply The address CLK output (for panel upper part) Address data output (R signal) Address data output (R signal) Address data output (G signal) Address data output (G signal) Address data output (R signal) Address data output (R signal) GND Address data output (B signal) Address data output (G signal) Address data output (G signal) Address data output (B signal) Microcomputer data bus Microcomputer data bus Microcomputer data bus Microcomputer data bus 3.3V power supply APL value output trigger signal 3.3V power supply The chip select input The chip select input Microcomputer address bus Microcomputer address bus Microcomputer address bus Microcomputer address bus Microcomputer address bus Test input terminal (unused) The subfield No output (the 0 bit) 3.3V power supply Test output terminal (unused) Address data output (G signal) Address data output (G signal) Function
98
PDP-433PE, PDP-433PU
No. 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
Pin Name VSS ABO37 ABO36 ARO36 ABO34 ADRCLKO4 AGO33 AGO32 AGO31 AGO30 AGO29 VDDI ABO27 AGO26 VDDI AGO24 VDDI ABO22 VDDI ARO21 ARO20 VDDI OVDDE-14 TDI RBI9 VSS RBI8 RBI6 RBI4 OVSS-09 RSTB GBI8 OVDDE-18 GBI5 GBI2 DEI BBI6 BBI3 VDI HDI RAI6 RAI2 TESTI0 OVSS-11 GAI7 GAI3 GAI0 BAI6 BAI3 BAI0 GND Address data output (B signal) Address data output (B signal) Address data output (R signal) Address data output (B signal)
Function
The address CLK output (for panel bottom part) Address data output (G signal) Address data output (G signal) Address data output (G signal) Address data output (G signal) Address data output (G signal) 2.5V power supply Address data output (B signal) Address data output (G signal) 2.5V power supply Address data output (G signal) 2.5V power supply Address data output (B signal) 2.5V power supply Address data output (R signal) Address data output (R signal) 2.5V power supply 3.3V power supply The JTAG input The R picture B aspect signal input (the ninth bit) GND The R picture B aspect signal input (the eighth bit) The R picture B aspect signal input (the sixth bit) The R picture B aspect signal input (the fourth bit) GND Reset input The G picture B aspect signal input (the eighth bit) 3.3V power supply The G picture B aspect signal input (the fifth bit) The G picture B aspect signal input (the second bit) DE signal input The B picture B aspect signal input (the sixth bit) The B picture B aspect signal input (the third bit) VD signal input HD signal input The R picture A aspect signal input (the sixth bit) The R picture A aspect signal input (the second bit) Test input terminal (unused) GND The G picture A aspect signal input (the seventh bit The G picture A aspect signal input (the third bit) The G picture A aspect signal input (the 0 bit) The B picture A aspect signal input (the sixth bit) The B picture A aspect signal input (the third bit) The B picture A aspect signal input (the 0 bit)
99
PDP-433PE, PDP-433PU
No. 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150
Pin Name TESTO7 TESTO5 OSDH BLK OSDB NC ARO1 ARO2 ARO3 ARO4 ARO5 ABO5 ARO7 ARO8 ABO8 AGO9 AGO10 ADRCLKO1 ABO11 ABO12 ARO14 ARO15 ABO15 ABO16 AGO16 ARO18 AGO19 OVDDE-05 UDAT13 UDAT10 UDAT6 UDAT3 UDAT0 OVDDE-07 LR RDBI CLKSEL UADRI10 UADRI7 UADRI3 CYCLEB BIT2 SFSTB OVSS-05 TESTO2 ABO38 ARO38 ARO37 AGO36 ARO35 Test output terminal (unused) Test output terminal (unused) OSDH input OSDBLK input OSDB signal input NC terminal Address data output (R signal) Address data output (R signal) Address data output (R signal) Address data output (R signal) Address data output (R signal) Address data output (B signal) Address data output (R signal) Address data output (R signal) Address data output (B signal) Address data output (G signal) Address data output (G signal)
Function
Address CLK output (for panel upper part) Address data output (B signal) Address data output (B signal) Address data output (R signal) Address data output (R signal) Address data output (B signal) Address data output (B signal) Address data output (G signal) Address data output (R signal) Address data output (G signal) 3.3V power supply Microcomputer data bus Microcomputer data bus Microcomputer data bus Microcomputer data bus Microcomputer data bus 3.3V power supply The panel LR select input Microcomputer read control terminal CLK select input Microcomputer address bus Microcomputer address bus Microcomputer address bus Address data output control signal Subfield No. output (the second bit) Address data output control signal GND Test output terminal (unused) Address data output (B signal) Address data output (R signal) Address data output (R signal) Address data output (G signal) Address data output (R signal)
100
PDP-433PE, PDP-433PU
No. 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200
Pin Name ADRCLKO3 ABO33 ABO32 VDDI ABO30 VDDI ABO28 ARO28 ABO26 ABO25 ABO24 ARO24 ARO23 ARO22 AGO21 AGO20 TDO TMS RBI7 TCK RBI5 RBI3 RBI1 OVDDE-16 GBI7 OVSS-10 GBI4 GBI1 BBI9 BBI5 BBI2 RAI9 CLK3 RAI5 RAI1 TESTI1 GAI9 GAI6 GAI2 BAI9 BAI5 BAI2 BAI1 OVSS-01 OVSS-02 OSDG ARO0 ABO0 ABO1 ABO2 Address data output (B signal) Address data output (B signal) 2.5V power supply Address data output (B signal) 2.5V power supply Address data output (B signal) Address data output (R signal) Address data output (B signal) Address data output (B signal) Address data output (B signal) Address data output (R signal) Address data output (R signal) Address data output (R signal) Address data output (G signal) Address data output (G signal) JTAG signal JTAG signal
The R picture B aspect signal input (the seventh bit) JTAG signal The R picture B aspect signal input (the fifth bit) The R picture B aspect signal input (the third bit) The R picture B aspect signal input (the first bit) 3.3V power supply The G picture B aspect signal input (the seventh bit) GND The G picture B aspect signal input (the fourth bit) The G picture B aspect signal input (the first bit) The B picture B aspect signal input (the ninth bit) The B picture B aspect signal input (the fifth bit) The B picture B aspect signal input (the second bit) The R picture A aspect signal input (the ninth bit) CLK input terminal (unused) The R picture A aspect signal input (the fifth bit) The R picture A aspect signal input (the first bit) Test input terminal (unused) The G picture A aspect signal input (the ninth bit) The G picture A aspect signal input (the sixth bit) The G picture A aspect signal input (the second bit) The B picture A aspect signal input (the ninth bit) The B picture A aspect signal input (the fifth bit) The B picture A aspect signal input (the second bit) The B picture A aspect signal input (the first bit) GND GND OSDG signal input Address data output (R signal) Address data output (B signal) Address data output (B signal) Address data output (B signal)
101
PDP-433PE, PDP-433PU
No. 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250
Pin Name ABO3 ABO4 OVDDE-02 ABO6 ABO7 VDDI OVDDE-03 ARO10 ABO10 AGO11 AGO12 ABO13 ABO14 OVDDE-04 OVSS-03 ARO19 TESTO1 UDAT14 UDAT11 UDAT7 UDAT4 UDAT1 VDRD HWRBI UADRI14 OVDDE-09 UADRI11 UADRI8 UADRI4 BIT3 BIT1 OVDDE-10 TESTO3 ABO39 AGO37 OVSS-06 AGO35 ADRCLKO5 ARO34 ARO33 ABO31 ARO31 ABO29 ARO29 OVDDE-12 ARO27 ARO26 ARO25 OVDDE-13 AGO23 Address data output (B signal) Address data output (B signal) 3.3V power supply Address data output (B signal) Address data output (B signal) 2.5V power supply 3.3V power supply Address data output (R signal) Address data output (B signal) Address data output (G signal) Address data output (G signal) Address data output (B signal) Address data output (B signal) 3.3V power supply GND Address data output (R signal) Test output terminal (unused) Microcomputer data bus Microcomputer data bus Microcomputer data bus Microcomputer data bus Microcomputer data bus V signal output Microcomputer wright control terminal Microcomputer address bus 3.3V power supply Microcomputer address bus Microcomputer address bus Microcomputer address bus Subfield No. output (the third bit) Subfield No. output (the first bit) 3.3V power supply Test output terminal (unused) Address data output (B signal) Address data output (G signal) GND Address data output (G signal)
Function
Address CLK output (for panel bottom part) Address data output (R signal) Address data output (R signal) Address data output (B signal) Address data output (R signal) Address data output (B signal) Address data output (R signal) 3.3V power supply Address data output (R signal) Address data output (R signal) Address data output (R signal) 3.3V power supply Address data output (G signal)
102
PDP-433PE, PDP-433PU
No. 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300
Pin Name AGO22 VDDI ABO20 OVSS-07 OVDDE-15 OVSS-08 RBI2 TRST GBI9 GBI6 OVDDE-17 GBI3 GBI0 BBI8 BBI4 BBI1 RAI8 OVDDE-19 RAI4 RAI0 FREERUN GAI8 GAI5 GAI1 BAI8 BAI4 VDDE OSDV VSS OSDR VDDE AGO1 VSS VDDI VDDI AGO5 AGO6 VDDI AGO8 VSS ADRCLKO0 VDDE ARO11 VSS AGO13 VDDE ABO18 VSS TESTO0 VDDI Address data output (G signal) 2.5V power supply Address data output (B signal) GND 3.3V power supply GND
Function
The R picture B aspect signal input (the second bit) JTAG signal The G picture B aspect signal input (the ninth bit) The G picture B aspect signal input (the sixth bit) 3.3V power supply The G picture B aspect signal input (the third bit) The G picture B aspect signal input (the 0 bit) The B picture B aspect signal input (the eighth bit) The B picture B aspect signal input (the fourth bit) The B picture B aspect signal input (the first bit) The R picture A aspect signal input (the eighth bit) 3.3V power supply The R picture A aspect signal input (the fourth bit) The R picture A aspect signal input (the 0 bit) The freerun control input The G picture A aspect signal input (the eighth bit) The G picture A aspect signal input (the fifth bit) The G picture A aspect signal input (the first bit) The B picture A aspect signal input (the eighth bit) The B picture A aspect signal input (the fourth bit) 3.3V power supply OSDV input GND OSDR signal input 3.3V power supply Address data output (G signal) GND 2.5V power supply 2.5V power supply Address data output (G signal) Address data output (G signal) 2.5V power supply Address data output (G signal) GND The address CLK output (for panel upper part) 3.3V power supply Address data output (R signal) GND Address data output (G signal) 3.3V power supply Address data output (B signal) GND Test output terminal (unused) 2.5V power supply
103
PDP-433PE, PDP-433PU
No. 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352
Pin Name UDAT8 VSS UDAT2 VDDI OVSS-04 UADRI15 VDDI UADRI12 VSS UADRI5 VDDI NC VSS AGO39 VDDE ABO35 VSS AGO34 VDDE ARO32 VSS ARO30 VDDI AGO28 AGO27 NC AGO25 VSS ABO23 VDDE ABO21 VSS VPD VDDE RBI0 VSS ACLK VDDI CLK4 VSS BBI7 VDDI BBI0 RAI7 VDDI RAI3 VSS CLK2 VDDI GAI4 VSS BAI7 Microcomputer data bus GND Microcomputer data bus 2.5V power supply GND Microcomputer address bus 2.5V power supply Microcomputer address bus GND Microcomputer address bus 2.5V power supply NC terminal GND Address data output (G signal) 3.3V power supply Address data output (B signal) GND Address data output (G signal) 3.3V power supply Address data output (R signal) GND Address data output (R signal) 2.5V power supply Address data output (G signal) Address data output (G signal) NC terminal Address data output (G signal) GND Address data output (B signal) 3.3V power supply Address data output (B signal) GND GND 3.3V power supply
Function
The R picture B aspect signal input (the 0 bit) GND CLK input (25MHz) 2.5V power supply CLK input (50MHz) GND The B picture B aspect signal input (the seventh bit) 2.5V power supply The B picture B aspect signal input (the 0 bit) The R picture A aspect signal input (the seventh bit) 2.5V power supply The R picture A aspect signal input (the third bit) GND The image system CLK input 2.5V power supply The G picture A aspect signal input (the fourth bit) GND The B picture A aspect signal input (the seventh bit)
104
PDP-433PE, PDP-433PU
Block Diagram
1 TC
2 SUB
3 GND
Pin Function
Pin No.
1 2 3 4 5 TC SUB GND VOUT VCC
Pin name
TPLH control pin Substate pin GND pin
Functions
105
PDP-433PE, PDP-433PU
Block Diagram
Loop Filter
4(6) 250 K
Xin
1(3)
Reference Divider
8 pF
Xout
Modulation Control
2(4)
8 pF
VCO / N
VDD
8(2)
6(8)
FSOUT
5(7)
3(5)
7(1)
(TSSOP Pin #)
VSS
S1
S0
Pin Function
No. Pin Name I/O
I/O I I O P P
Type
Analog CMOS/TTL Analog CMOS/TTL Power Power
Function
Pins form an on-chip reference oscillator when connected to terminals of an external parallel resonant crystal. Xin may be connected to TTL/CMOS external clock source. If Xin connected to external clock other than crystal, leave Xout (pin2) unconnected. Digital control inputs to select input frequency range and output frequency scaling. Refer to Tables 7 and 8 for selection. S0 has internal pulldown. S1 has internal pullup. Loop Filter. Single ended tri-state output of the phase detector. A two-pole passive loop filter is connected to Loop Filter (LF). Modulated Clock Frequency Output. The center frequency is the same as the input reference frequency for FS781. Input frequency is multipled by 2X and 4X for FS782 and FS784 respectively. Positive Power Supply Power Supply Ground
106
PDP-433PE, PDP-433PU
Block Diagram
V SUS 1 V SUS 2 V SUS 3 V SUS 4 N.C. 5
R14
40 OUT H 39 OUT H 38 OUT L 37 OUT L 36 N.C. 35 POWER GND 34 POWER GND 33 POWER GND 32 POWER GND 31 N.C.
D7
D5 D3
D6
IC2
N.C. 17
C5
R5 VDD HIN SD HO VB VS VCC COM LO TR10 C8 R13 D10 C4 D4 R11 C7 R6 TR6 D9 ZD1 C6 R12 TR9 TR5 D8
30 PL1 29 PL1 28 N.C. 27 PC1 26 PC1 25 PC2 24 PC2 23 N.C. 22 PL2 21 PL2
LIN VSS
107
PDP-433PE, PDP-433PU
8. PANEL FACILITIES
Plasma Display
CHANNEL
VOLUME
VOLUME buttons
108