Académique Documents
Professionnel Documents
Culture Documents
2011
INDEX
SRNo. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Particulars Electronics Hobby Project Electronics Higher Project LED Light Project Display Light Project Electricals Project 8051 Microcontroller Based Project Microcontroller Base Project Microcontroller Base PIC Project Microcontroller Base RF Project PC Based Project RFID based Project Robotics Project Development Board Trainer Board/Self Learning KIT Automation Project Page1 ProjectNo. 1600 601700 701900 901950 9511000 10011050 10511100 11011200 12011300 13012000 20012500 25013000 30013500 35014500 45015000
SCIENCE&TECHNOLOGYPROJECTLIST
Particulars
2011
Disipline IC
S.No.
3 4 5 6
10 0 11 12 26
CAR HORNS
Electronics Car Horn ( 810 + 555 ) ( 6 - 18 V ) This is a simple & at low cost project designed for car using TBA 810+555 chip.
Page2
SCIENCE&TECHNOLOGYPROJECTLIST
2011
27 28 29 30 31
Car Reverse Horn (UM 66T / L) (12V ) This is a easy project designed for Car Reverse Horn. Multitune Car Reverse Horn (12V) Produce 12 different tunes for Reverse Horn. Scooter Brake Horn ( UM 66T/L ) This circuit using UM66 melodious warning Brake Horn. 4 Sound Car Reverse Horn (UM 3561) 3V Electronics Eye This circuit produces the sound while light Fails & stops while light comes back.
SOUND EFFECT 52
Mosquito repellent ( Domestic ) ( 1.5 V ) This is the A stable Multi Vibrator which generate the desired frequencies for ran away mosquito. Electronic Harmonium ( 9V ) This is simple Harmonium using 555 IC,which gives 15 different music. 3 Gun Sound Generator (UM 3562) (3V) This circuit uses 8 pin CMOS IC.It produces 3 different Gun sound. Steam Engine with Whistle Sound (New) Multi Melody Generator with Instrumental Effect-0606 This versatile melody generator is capable of generating various English and Hindi version melodies using UM3481A and WR630173 tone generator respectively. Instrumental effects can also be produced with the same circuit.
53 54 55 74
AUDIO EFFECTS 76
Dancing Light / Sound Level Indicator (5-12 V ) This simple circuit appeal for stereo system or Cassette Plyer on Sound level indicator. Digital Telephone Amplifer (New)(LM 386) Condenser MIC Amplifier-EP-7 Mic sound amplification with both fixed and variable outputs can be obtained using this kit. The two-stage amplifier is capable of providing sufficient gain to pick up even the slightest whisper. Hearing Aid-0608 This low-cost, electronic hearing aid employs a TDA 2822M(8 PIN-DIP package)audio amplifier IC.Transitor BC547 and associated components form the condensor microphone signal preamplifier.The audio power output of this unit is 10 to 15 MW.
77 78
80
Page3
2011
101
Quality FM Transmitter-0408 The digital like sound quality that FM offers is the reason that many people prefer to have their own transmitting station in FM band. This quality FM transmitter can transmit chosen music in FM band. To receive its signals, any conventional FM radio receivers can be used.Without compllicating the functionality,this circuit transmits the signals just by using discrete components.It provides an easy wau to transmit less distorted,low noise music with in a range of about 200 meters. Fm Transmitter (9V) You can hear your voice in FM receiver kept at distance tuned in FM Frequency. FM Transmitter 300 Meter (9V)(New) FM Transmitter 2 K.Meter (9V)(New) FM Transmitter 3 K.Meter (9V)(New) FM Transmitter 3 K.Meter (9V)(New) MOSFET Based Pre-Amplifier for FM Radio Dxing-0311 Frequency Modulated (FM) transmission can be received within a range of about 40 Kms. To receive your favourite FM radio station beyond this range, the only option left is to connect an external pre-amplifier at the receiver end. This circuit acts as FM booster attached to your present FM radio receiver and enables one to receive FM in fringe areas.
Long-Range FM Transmitter-9912 The high-power output obtained using a power amplifier stage allows a range of about 2 km for this FM transmitter. Reasonable good signal quality and strength are possible with little adjustments.
108
109
Wireless TV Headphone-0303 As most of TVs nowadays come equipped with audio in/out and video in/out RCA sockets. Connect audio output (headphone socket) of your TV to this circuit to transmit the sound of TV as FM signals. Using a portable FM receiver with headphone, watch your favorite TV program without distrubing others. Cordless FM MIC-9605 The voice at condenser microphone can be listened through a standard FM receiver using this circuit. The range of this FM transmitter can be easily enhanced with little modifications. FM Booster FM booster can be between your FM reciever and the antenna to listen to distant commercil FM stations clearly.
110
111
GAMES 126
Digital Dice-0510 The digital electronic dice circuit acts like a normal dice and uses four different logic gate combination to bring out the six faces of the dice. Seven LEDs are suitably positioned on the board. When you place your finger on the touch plate, the LEDs wil glows. Griposcope (3-9V) Can also be used as a lie Detector. Page4
127
SCIENCE&TECHNOLOGYPROJECTLIST
2011
Two In One Electronic Games (9 V ) It incorporated two facilative games gambling & Indoor Cricket. Quiz Monitor (4 Channel) 12V (New) (CD 4012+4013) Electronic Roulette Wheel With 2 Digit (9V) (New) (CD 4033) Electronic Decision Maker (New) (CD 4046)
DOMESTIC
Clap based Switch For Device-0303 Clap Switch (12 V ) Simple electronic swithch activated by a clap can control (ON/OFF) fan light Radio & Tape. Touch Sensitive Switch-EP-11 Sometimes one may want to switch a lamp just by touching it. This circuit provides a very simple and reliable way to do just that. The connected appliance will be turned ON by a slight touch of finger at the sensor. Another touch at the OFF sensor will turn it OFF. This can also be used as ahidden switch or electronic lock by concealing the touch sensors. Hit Switch This versatile hit based switch is electronic equivalent of a switch. This circuit serves as an on/ off control for incorporation in a wide variety of electronic design.The circuit uses a Piezo electric diaphgram. Listening Bug (9V) It is simple circuit in - expensive circuit to listen to the conversation on in your adjoining room. Powerfull Listening Bug(9V)(NEW)(LM741) Parallel Telephone Ringer Due to high volume of your hi-fi audio/video systems or any other reason sometimes telephone ringing in other room is not heard. In addition to provide indication that your telephone is ringing in other room this telephone extension ringer avoids overhearing of conversation by an undesired person at other end. Parallel Telephone Ringer (New)(Bel 1240) Musical Hold On for Telephone Using this add-on external circuit attached to your telephone a melodious music is generated on telephone line. During the entire hold-on interval, person on other end enjoys a pleasant music. To resume talking when you are back, just flick the switch to OFF mposition.A Red LED included in the circuit that phone line is on hold and it automatically turns OFF when music stops. Hold On Music For Telephone This is the external ckt to telephone line which gives the pleasant music during the hold on interval. Telephone Call Recorder-9507 This telephone message recorder records all the conversations on tape-recorder. In case nobody attends the call, it records the incoming ring signal only. Phone to FM Listening Bug (New) Page5
153
156
157
158 161
162 163
164
165
167
SCIENCE&TECHNOLOGYPROJECTLIST
2011
168
169
176 177
Low-cost Transistorised Intercom-9910 Voice at one end is amplified and listened at the other end through a loudspeaker as a one-way intercom. A two-way intercom can be similarly assembled using two such kits. Two Way Intercom (9V) This is simple intercom system for communication of two persons in the same building OR office. 20sec Voice Recording (6V) 60 Sec Voice Rec Message (6V) A re-recordable voice chip with non-colatile memory gives to store 1/4/8 voice msg in single chip with individual trigger & no batt backup. 8 Minute Voice Recording & Play Back (Message Box) 16 Minute Voice Recording & Play Back (Message Box) 120 Sec. Message Recorder (ISD 25120) (New) Three Octave Organ-EP-4 Organ is a musical keyboard instrument that produces a wide range of sounds at different volumes. This circuit resembles the working of organ by electronically producing 12 musical notes. This electronic organ is designed to produce notes in high, medium and low octaves,Selection of different octaves is done by switches S1 and S2. Touch Dimmer This is versatile three-step touch dimmer for varying the lamp intensity according to brightness required in the room. The circuit increases lamp intensity in steps, from off to low, medium, high and again off. The lamp stages are advanced sequentially by simply touching the touch plate connected to touch wire. At power-on condition, lamp is in OFF condition. Digi Teacher-EP-9 Now a days, the digital electronic techniques are employed to number of electronic devices and are applicable in diverse fields such as automobiles, electrical appliances, instrumentation and control equipments. Acting as Truth Table evaluator cum electronic learner circuit, this kit gives hands on practice for learning and understanding digital design basics.It displays the output using LEDs. Digital Object Counter The circuit using 74C926 counter utilizes the LDR to show the counting of the object. 2 Digit Door Bell Counter (6V)(New)(CD 4026/555) 2 Digit Strom Distance Counter (9v)(New)(NE 555) 3 Digit Counter (New)(CD 4093) The high-frequency signal generated by a transformer is useful as pest-repeller. The intensity can be easily varied by tuning the preset. Emergency Light Using CFL This circuit provides automatic switch-on of compact fluorescent lamp (CFL) when AC mains supply goes off. Charging mode is switched back when the supply is resumed. Page6
191
192
193
198
SCIENCE&TECHNOLOGYPROJECTLIST
2011
199
200
201
Water level Indicator-9702 This simple and easy-to-install circuit gives both visual and aural indication when the water tank is full. You need to fit the probes at the desired water level in water tank. Remote Control for Home Appliances-0505 This handy circuit can be used to switch on and off any of your home appliances or any electrical device with a single press of your TV, VCD or DVD remote control. This low-cost circuit is based on 4017 counter IC which receives trigger pulse from IR sensor and switches on the relay through which electrical devices are switched on & on receiving the 2nd pulse the device is switched off. Automated School Bell-0410 The Circuit is useful for the Educational Institutes etc. This circuit provides an automatic alarm 8 times after an interval of 45 minutes each. and after 4 intervals provides lunch breaks for 30 minutes. Automatic Night Lamp Dimmer with morning alarm This circuit serves dual purpose, depending upon intensity of light rays detected. One part of the circuit automatically detects darkness to switch ON a white bright LED which acts as night lamp. Its another part senses daylight to switch on a melodious music in the morning. No external DC power supply is required,as the circuit operates on direct AC power supply line. But , provision for battery backup is provided to power the circuit in case of mains failure. Automatic Porch Light with Melody-0212 While you park your vehicle in the garage, this porch light automatically switches on for a specific duration. A melodious sound can also be heard at the same time. Time duration can be easily varied using a preset. Ionizer Mains (230 V AC ) An environment friendly project based on theory of IONISATION can be used as an air purifier. 1 Hz Generator (9V) The circuit generates a very precise 1 Hz square wave signal. Electronics Bicycle Lock Numeric Water Level Indicator with Display Automatic water Level Controller Touch Plate / Switch ( Glass Epoxy) (12V ) This simple ON/OFF touch plate by using the NAND Gate IC 4011,which has connected as a flip-flop.(There are two plates for ON-OFF). Sunset Lamp
202
203
221
DIGITAL CLOCKS
Digital Alarm Clock ( 0.5" Duplex Dis) Red And Green Digital Wall Clock (3 1/2 " Dis. ) (5 mm LED) This is a simple alarm clock with using Chip 8560 TMS 3450 with Battery backup facility.
Page7
SCIENCE&TECHNOLOGYPROJECTLIST
TIMERS
2011
555 Timer (9V-12V) This is capable of Drive Relay with time delays From 1 sec. To 100sec. Time Switch (6V ) This timer is very useful for NICD chargers. 555 Timer with On/Off Indicator (12V)(new) 1 to 5 mins 200/240V Timer (new) Knotted Handkerchief (timer up to 120 minutes ) (9v) This reminds one to do something in fact it is extrmely compact timer. Kitchen Timer (Up to 17 minutes ) ( 9 V ) This circuit adjustable between 1 to 17 Minutes provies Audible time alarm. Timer with Audio Alarm (9V) (CD 4060) This circuit gives a audible warning from 1min to 120min. Telephone Cut off Timer 1-20 Minute (new) Timer for Students-9910 This timer gives alarm after a preset time period and a few beeps at half the selected time. The timer could be programmed for other time periods as well. Sound Operated Timer-8905 This electronic switch gets activated by the sound of a clap. It can be used in a sound-operated motor driven toy car or any other gadget.
285
303
304 305
306
SCIENCE&TECHNOLOGYPROJECTLIST
2011
307 311
312 313
Digital Panel Meter (New Led Version ) (5V) CMOS Function Generator (6 V) The circuit offer a choice of sine,Square & triangle wave form & Freq. range from 12Hz to 70KHz PH Meter (+-9V) Acidity/Alkalinity measurement by LCD range from 0 to 14PH. PT 100 Thermometer (9V) This thermometer has unusually large of - 100'C to +1000'C Theses means the demand for accurate temperature measurement. LM 35 Digit Thermometer (9V) (New) Digital Multimeter
ALARMS
Blown Fuse Indicator-0004 Green LED glows in normal condition, while a blown fuse is indicated by a red LED as well as an audio alarm. Sensitive Vibration Detector-0511 The Vibration detector (piezo element) in this circuit can be used to detect the vibration of the rolling shutter guard and alarm you when unauthorised person tries to open it. The load in the circuit can be an AC operated electric bell or bulb used as alarm device.The alarm can be stopped using a push to off switch given in this circuit. Bathful Indicator (5 V) This low cost solution for non wastage of water which alerts you by active buzzer when water level is reach. Power Failure Indicator-Ep-16 The power supply failure and blown fuse condition both are indicated by sounding an alarm using a loudspeaker. Liquid Level sensor (12 V ) Liquid level controller wired around a single chip & sense the level and alert you. Heat Sensor with Fan Cooling (12V)(New) (LM 741) Heart Bit Monitor (9V)(New)(LM 386) Electronic Guard For Blind-0207 Using this microcontroller based aid for visually impaired persons, any obstruction in the path can be sensed easily. When obstruction is too near, the loudness level of sound coming through earphone gets increased. Thus the user holding the unit gets a rough idea of his distance from the object.The important feature of the circuit is its small size owing to use of less number of components.After little modifications,the same circuit can be used in robotic toys or in object counters. Photo Sensor with control Relay (New) Fire Alarm (9V) Here is a simple fire alarm circuit build around 555 timer IC a reverse biased germanium diode DR 25 is used as a heat sensor.
327
328
329
340 351
Page9
SCIENCE&TECHNOLOGYPROJECTLIST
2011
352
Knock Alarm-0211 This circuit converts knock on door, cars dashboard, drawer, etc into a loud alarm using a loudspeaker. It can also be used to warn you of any unauthorised entry during night time, if installed at your doorstep. Intruder Alarm This circuit automatically activates a loud alarm whenever any unauthorized entry is attempted. To reset the circuit, there is no need to replace the broken wire or to turn OFF the unit, as is the case with other security alarms. The alarm can be turned OFF just by a simple flick of a switch.The unit power on Identification by LED use also provided here forbetter monitoring. Smoke Alarm-0112 This smoke detector employs a photo interrupter module that activates an audio alarm via a loudspeaker. The sensitivity can be easily adjusted by varying the preset. Smoke Alarm (NE 555) Burglar Alarm-EP-3 This circuit sounds a loud alarm in the case of an unauthorised entry. Wire loop gets broken whenever such an attempt is made. Fire Alarm-9301 This fire alarm uses a DR25 diode as sensor to sense fire and activate a loud alarm. Fridge Alarm (12 V) This is simple LDR circuit designed for Fridge or Freezer which give alarms or sound when your door of fridge are not properly closed. Musical Visitor's / Intruder Alarm (3V) It is simple circuit to monitoring intruders by using proximity magnetic switches. Knock / Earth Quake Alarm (9V)(New) Stop Thief (Buglar Alarm for Car ) (12V) This is simple circuit designed for car which protect your car from thief's with engine trouble. Molestation Alarm (9V) Power failure resumption alarm This circuit sounds an alarm whenever AC mains fails or resumes. It can be easily installed where you want to monitor the status of the mains supply. Musical Buglar Alarm / Doorbell (LDR Operated ) (3V) This circuit can operate as a light activated burglar alarm by the addition of preset and LDR. Infrared INT Alarm (Long Range) (12V) Power Supply Failure Alarm-0107 This circuit indicates power supply failure by sounding a buzzer. No external DC supply is required and power-on condition is indicated by an LED. Time duration can be varied with little modifications.
353
354
355 356
357
358
362 363
364
365 366
Page10
SCIENCE&TECHNOLOGYPROJECTLIST
2011
Musical Siren Alarm (3V) This is musical siren without using IC operated by 2 transistor. 4 Led Water Level Indicator with Alarm(6V)(New)(CD 4066) Touch Sensitive Siren (New) Twilight Switch (12 V ) This switches the light on dusk & off at down. Light Sensitive Switch (230V) A versatile light operated switch Max.220V Touch Switch (using ic 555 Multivibator) (New) (NE 555) Electronic Auto Dipper While driving at night, the high beam of head light lamp of vehicle approaching from opposite direction causes the problem of glare for both the drivers. This circuit solves the problem by making the dipper action automatic. As soon as it senses the light rays coming from opposite direction it automatically turns lamps from High to Low intensity. Water Level Controller (12V) Improved water level controller has been provided with two flip flops for the two tanks and each tank has three probes to monitor its status.
380
403
404
405
Electronic Watch Dog This circuit produces an alarm sound when a person crosses the gate. The Circuit comprises of Transmitter & Receiver which are mounted face to face on opposite pillars of the gate in a manner so that when someone interuppts between the two it gives an alarm. Magic Eye-9601 This magic eye fitted on the bottom of door entrance obviates the need for a call bell. It can also be used as an automatic guest indicator at homes or as a burglar alarm in banks. Electronic Digital Combination Lock (New) (CD 4017) Smart Cellphone Holder-0507 This smart cellphone holder makes sure that you do not forget to carry your mobile phone. If you have forgotten to carry your cellphone, the LED light fitted in the cell phone holder will stop flashing to indicate that the mobile phone is not in the holder.
406 407
Page11
SCIENCE&TECHNOLOGYPROJECTLIST
2011
408
Digital Security System-0505 This circuit can help you from the intruders and strangers. Very thin copper wire loops has to be wired around your house and if any of the copper wire loops is broken, the display displays the particular number of the loop with buzzer sound. if more than one loops are broken it will display the sum of their lopps.
Simple Digital Security System (New)(CD 4511) Security System (New)(NE 555) Anti Bag Snatching Alarm Incidents of bag snatching are increasing nowadays. Many a times the snatcher can be caught easily if a loud alarm is raised. The kit uses plug and socket arrangement to raise the alarm whenever any snatching attempt is made. Thus, while travelling, this kit entitles the person to carry cash or valuables without fear. Using the hidden key, only owner can turn OFF the alarm. Luggage Security Systems-0005 This circuit gives an alarm sound when someone tries to cut the luggage chain. Different sound effects are possible after doing simple connections. Long Range Burglar Alarm using laser torch This Circuit operates at a frequency of 5 khz. If the transmitter & receiver parts are properly aligned it can work upto a distance of even 30 meters When the objects cuts the transmitter and the receiver parts. Metal Detector (9V)(New) Door Opening Alarm (New) IR Remote Switch-0203 ON/OFF switching operation of a remote appliance can be done using this remote control. The circuit uses any TV, VCR, VCD or CD player remote as transmitter. Indication of different output stages is provided by LEDs. This helps in better understanding. IR Auto Switch I/R wash Basin Proximity switch(12V) (New)(Is 471 IR Sensor). I/R Remote Switch (Universal) This circuit use one channel universal remote control. I/R Remote Control On/Off Switch (12V) 4 Channel Long range IR Control (12V) IR Object Counter This circuit can be installed in public places to count the number of people or objects passing through the transmitter & receiver. The circuit operate at a frequency of 38 Khz . The count will be displayed through the calculators. Remote Operated Musical Bell-0310 It uses any TV remote control to operate a 12-tone musical bell. This Infra-Red (IR) receiver unit is capable of responding to IR rays transmitted from any TV, VCR, VCD or CD player remote. When any of the buttons on the remote is pressed, the receiver detects it as pulse through its own IR sensor and plays one musical tone. The approximate range of the circuit is 10 meters. Page12
412
413
432
SCIENCE&TECHNOLOGYPROJECTLIST
2011
Infrared Security Alarm (12V)(New)(74LS14) CCTV Night I/R Lluminator Watching (12V)(New)(7812) IR Remote Control Timer-0305 The circuit uses IR transmission for remotely controlling ON/OFF operation of upto two electrical/electronics appliances. Pressing push-to-on switch from a distant transmitter, normally OFF appliance is turned ON and another normally OFF appliance is turned ON for some specific time period. This time period can be varied in the range of 0.11 to 110 seconds for given set of components and range of remote is about 3 meters. 4 Channel Long range RF BASE Remote Control (Push to on type) (12V) 4 Channel Long range RF BASE Remote Control (on/off) (12V)300 meter 4 Channel Long range RF BASE Remote Control (Push to on) (12V)300 meter 4 Channel Long range RF BASE Remote Control (on/off) (12V)
POWER SUPPLIES
General Purpose Power Supply (2 Diode /4 Diode) General Purpose Power Supply (4 Diode /2Cap ) Simple rectifier circuit for AC to DC conversion. + /-15V/ 1AMP. Power Supply Regulated Power supply with short circuit protection. 15V /1AMP. Power Supply Regulated power supply with short circuit protection with AMP current capacity. Versatile Power Supply-0602 It is a DC regulated variable power supply that can deliver 3.3V up to 15V ,1Amp output using an adjustable regulator IC LM317. 78L/79L General Purpose Power Supply Versatile Power supply using 78L series IC's with Amp current capacity(5V to 24V) 5V/ 500 MA Power Supply(LM129) Stabilized power supply for exact output of 5V with regulation. Regulated Power Supply (2 Diode 3 to 6 AMP) Regulated Power Supply (4 Diode 3 to 6 Amp) Mulity Use PCB with +/- Supply Pcb (NEW) (LM 317) 3 AMP. / 5V Power Supply 5V regulated power supply with 3AMP current capacities. L - 200 Regulated Power Supply Variable regulated power supply fully adjustable between 0-18v and 0-1.8A respectively. Adjustable Regulated Power Supply (LM 317 T ) Variable power supply from 1.25V to 25v at 1 AMP. 3 AMP. Variable Power Supply (1.5 V To 24 V ) Variable power supply from 1.25V to 24v at 3 AMP current.
519 520
Page13
SCIENCE&TECHNOLOGYPROJECTLIST
2011
0 - 30V Regulated Power Supply (1Amp) Variable Voltage source from 0-30V with adjstable current limiting facility. IC Power Supply (1V - 10V/1A) Variable Stabilised power supply with adhustable current limiting facility. Variable Power Supply with Digital Control-0404
A regulated power supply is one of the most important and essential requirements in electronic lab. The available power supply must provide variable outputs in steps. This kit gives variable and fluctuation-free DC voltage as output in the range of 1.5V to 12V. It also provides proper display using LEDs as indicators and outputs here are easy to select.
584
602
Digital Voltmeter-0707
Digital Voltmeter is designed as a panel meter and can be used in DC power supplies panels or where it is necessary to have an accurate indication of the voltage.
604
605
606
607
Page14
SCIENCE&TECHNOLOGYPROJECTLIST
2011
608
609
610
611
612
613
614
615
616
617
619
Page15
SCIENCE&TECHNOLOGYPROJECTLIST
2011
620
Current sensor Computerised Electrical Equipment Cellphone based Voice Acknowledgment Solar Light System with 10W Panel Ibutton
702 703 704 705 706 707 708 709 710 711 712 713 714 715 716 717
6 LED Dancing Light (3V) 6 LED Dancing Light (9V ) 24 LED Dancing Light (12 V)
This is a simple multi vibrator circuit-using transitor.
OM (12V)
This circuit is arrange by LED's which idicate sign.
Swastik (12V) LED Ornaments (cross) (9V ) LED Ornaments (Square) (9V) LED Ornaments (circle) (9V) LED Ornaments (Spiral) (9V) LED Ornaments (Star) (9V)
The purpose of this circuit gives you an exact idea how you can imagine the multi sign by LED's.
Running Led (New) (NE 555) 60 Led Chaser (4 Ch) 150 Led Chaser (6 Ch) 300 Led Chaser (6 Ch)
The circuit descibed here generates a unique running light effect each column in a row of 4 or 6 glow sequentially.
16 Channel Auto LED Running Light with Flashing LED (12V)(New)(74LS04) Low Power LED Flasher (9V) (New) (NE 555) WelCome LED Dis. Board With 8 Alphabet Ckt . Board
This is simple LED Board in sign of WELCOME.
Page16
SCIENCE&TECHNOLOGYPROJECTLIST
2011
906
907 908
909
910
3 way Traffic Light (New) (CD 4017) Moving Light (New)(NE 555 + CD 4017)
Electrical Project
Motor Speed control by PC from the RS232 serial port by varrying pulse duty cycle
Using pulse width varying technology so generated by the PC with Rs. 232 interface through a Micro controller enables the speed control of motor from the Pc by a motor driver IC controlled from the microcontroller.
EC / EE
Page17
SCIENCE&TECHNOLOGYPROJECTLIST
2011
EC / EE
952
953
Single phase induction motor soft start by stepped delay of reducing firing angle
Charge and discharge of a capacitor at the switch on time and generating a saw tooth voltage is then compared by a comparator to reduce the firing angle from 180 degree to 0 degree progressively to achieve soft start of a induction motor.
EE
954
High voltage dc upto 3kv from ac by using diode and capacitors in ladder network
1000 PIV diodes in combination with 100MFD electrolytic capacitors forming a ladder network multiplies the input AC to develop 12 times approximately DC output.
EE
955
EE
956
Non contact tachometer based upon reflected infrared signal with LCD display
This project uses the IR transmitting and receiving technique by reflection of modulated IR rays from any rotating object such as a motor shaft to send interrupt signal to a programmed microcontroller to enable display of the speed. The display can either be a LCD or simple 7 segment LED type. This becomes a contact less tachometer.
EC / EE
957
EE
958
GSM based monthly Electricity energy meter billing with display to the user
Domestic electricity consumed is displayed in rupee terms on daily and monthly basics to the user and billing details sent over GSM network form the user to the department for generating the printed bill..
EE
959
PID/FUZZY LOGIC CONTROL for a brussless DC motor to run at the exactly entered speed
Precise speed entered through a numeric key pad interfaced to a micro controller maintains the entered speed of a BLDC motor by sensing shaft mounted IR sensors working on a closed loop circuit by a half brige ac to Dc circuit comprising 2 SCRs and 2 Diodes .
EE
960
Password based circuit breaker control to ensure electric line man's safety
The micro controller based door locker is an access control system that allows only authorized persons to access a restricted area. The system is fully controlled by the 8 bit micro controller AT89C51 which has a 2Kbytes of ROM for the program memory. The password is stored in MC can be changed at any time.
EE
Page18
SCIENCE&TECHNOLOGYPROJECTLIST
2011
EE
961
Remote speed control by thyristor trigger angle change with display of delayed firing angle
Using a standard TV remote with IR sensors interfaced to a micro controller , reads the coded data from the remote to activate the corresponding output pin to change the time delay for the thyristor firing in 8 steps that drives with varying speed the induction motor.
962
Precise DC power by pre stage thyristor firing angle control and post stage linear control
DC power is controlled with zero crossing detectors and sending to the microcontroller to fire thyristors using the opto isolator. The ac power is applied to the bridge rectifier comprising of diodes ,triacs and SCRs to get controlled DC at the output.
EE
963
EE
964
EE
965
Developing islanding arrangement automatically for grid on sensing bad voltage or frequency
This paper presents the development of a microcontroller based islanding detection for grid connected inverter with very simple under/over voltage and under/over frequency islanding detection algorithms. The microcontroller monitors the under/over voltage and under/over frequency from utility grid and the processed value of voltage and frequency for turning on/off the relay between a grid connected inverter and the utility grid.
EE
966
Three phase star delta starter using relays and adjustable electronic timer for induction motor
Star/Delta starters are probably the most common reduced voltage starters in the 50Hz industrial motor world. This project operates a 3 phase motor at 440 volt AC mains supply 50 Hz with a set of 12 volt DC relays, an electronically adjustable timer and a set of relays.
EE
967
Soft start of 3 phase induction motor by using 2 nos. Back to back scrs in each phase
Here we use 6nos of silicon controlled rectifiers in anti-parallel, two in each phase which are phase controlled in a similar manner to a light dimmer, where they are gradually turned on for a part of each cycle to control the voltage by varying the conduction angle of the SCR. Increasing the conduction angle will increase the average output voltage. By variation of the conduction angle, the output voltage can be reduced during starting and then the SCRs are bypassed.
EE
968
EE
Page19
SCIENCE&TECHNOLOGYPROJECTLIST
2011
EE
969
970
Three phase fault analysis with auto reset on temporary fault and permanent trip otherwise
six number of step down transformers used for forming one star and another delta at the output with a set of switches to inputs LL, LG, 3L fault that triggers a 555 timer in monostable to reset or permanently trip the output relay connected to another 555 timer in astable.
EE
971
Cycle stealing of mains supply used to control ac power without generating harmonics
Cycle stealing is a method to remove portions of full cycles/one cycle of an AC signal for controlling AC power across AC heater loads controlled by a set of switches interfaced to a microcontroller with a loaded programme in the memory as required by an industrial furnace.
EE
8051
1002
8051
1003
8051
1004
8051
1005
8051
1006
Home Automation Control System using DTMF Telephone Line (12V DC)
Dial your number using DTMF phone or cell phone from anywhere in world and remotely turn On/Off any of 8 relays.The MCU on ther interface senses Telephone ring,Automatic telephone pick up,and line hang up,displays information on a 16x2 LCD module and controls the relay switching.This interface uses the popular MT8870 DTMF decoder IC analog with AT89C52.
8051
Page20
SCIENCE&TECHNOLOGYPROJECTLIST
2011
AT89c51
1007
1008
8051
1009
8051
1010
8051
Real Time Clock using (AT89S8252) Electonic Voting Machine using IC 89C51 Stop Watch Using IC 89C51 Count down Counter Using Atmel AT 89C51 Fastest Finger First using micro 89C51 Microcontroller basedDC Motor Controller using AT 89C51 Microcontroller base Code Lock (Using AT 89C2051) Microcontroller based Count Down Timer AT89C2051 - 0603
Here is a microcontroller based timer that performs countdown operation for upto 99 minutes with two 7-segment displays showing the actual time left. AT89C2051 chip is used in this circuit. The program can be easily modified according to users requirement.
1019
1020 1021
Microcontroller based LED Light Chaser Microcontroller based Bi-Directional Visitor Counter-0701
Here is a low-cost AT89C52 microcontroller-based visitor counter that can be used to count the number of persons at a place. It consists of three 7-segment displays (LTS543 ) to display the number of visitors upto 999. The circuit works off a 5V DC supply.
1022
Page21
SCIENCE&TECHNOLOGYPROJECTLIST
2011
1023
1024
1025
1026
1029
1030
1031
1032 1050
1052
Page22
SCIENCE&TECHNOLOGYPROJECTLIST
2011
1053
1054
1055
1056
1057
1058
1059
1060
1061
1062
Page23
2011
1101
PIC16F..
1102
PIC16F..
1103
Stepper motor controller using micro controller (kit with 8v2 2 phase unipolar stepper motor)
This kit is very useful to control a 2 phase unipolar pm type DC stepper motor. Kit include circuit diagram, working explanation, part explanation, assmbling instruction, a basic discription of stepper motor component data sheet. excellent for eng. student.
PIC16F..
1104
PIC16F..
1105
PIC16F..
1106
Micro Controller Based wind Speed Meter with 16x2 LCD Display
A completely solid-state anemometer using ultrasonic Techniques to measure wind speed.Highly accurate. LCD readout in metric or imperial Displays up to 50 mph.Kit Comes Along with Circuit Diagram,Working Exolanation,Part Explanation,Assembiling Instruction & component.
PIC16F..
1107
PIC16F..
1108
PIC16F..
1109
PIC16F..
1110
PIC16F..
1111
PIC16F..
Page24
SCIENCE&TECHNOLOGYPROJECTLIST
2011
1112
PIC16F..
1113
PIC16F..
1114
PIC16F..
1115
Smart Card Based Door Access System with LCD [12V DC]
This is smart card based Access system for Bank ATM,Bank Lockers,Schools,Collage and home security application. Its using micro controller and smart card(memory card). (kit with four card)
PIC16F..
1116
PIC16F..
1117
PIC16F..
1118
PIC16F..
1119 1120
PIC
1121
PIC
1122
PIC
Page25
SCIENCE&TECHNOLOGYPROJECTLIST
2011
PIC
1123
1124
PIC
1125
Street light that glows showing the road ahead for km only on sensing vehicles or any movement
Emitting Diode (LED) replaces HID lamps by engaging a programmable microcontroller that controls intensity by pulse width modulation which enables energy saving during late nights considering low traffic density. The pulse width becomes very narrow on sensing no movement of vehicles. As the vehicle forwards, the intensity goes on increasing for few lights ahead and as it passes away the intensity goes on falling.
PIC
1126
PIC
1127
DTMF based sine wave generator for very specific pure sine wave for reference purposes
DTMF encoder IC is fed from a micro controller interfaced to 8 push buttons for generating very precise sine wave frequencies for calibration purposes.
PIC
PC Based Project
1301
8 Channel Remote Control using Printer port [12V DC]
This kit with the help of a computer program can control External Equipment Using your printer Port with the of control Relays.Kit Comes Along With Circuit Diagram,Working Explanation,Part Explanation,Assembling Instruction,Basic Desciption of PC Serial(RS232) port & Component data sheets.
1302
1303
1304
1305
Page26
SCIENCE&TECHNOLOGYPROJECTLIST
2011
1306
1307
1308
1309
1310
1311
1312
1313
1314
1315
Page27
SCIENCE&TECHNOLOGYPROJECTLIST
2011
1316
1318
1319
1320
PC Based Timer-0502
This circuit interfaced with PC computer through D-25 pin male connector, can switch on and switch off the device for a particular timing required by the user. The program is written in C languages & compiled in Turbo C compiler. The maximum timing of the circuit is for 18 hours.
2018
EC
2019
RFID guided automatic parking permission for vehicles in cellar at commercial complexes
RFID card swiped over the RFID card reader by the vehicle driver enables the motor interfaced through the driver IC to the controller to open the gate for vehicle entry.
EC
Page28
2011
2501
2503
2505 2506 2507 2508 2509 2510 2511 2512 2513 2514 2515 2516 2517 2518 2519 2520 2521 2522 2523 2524 2525 2526 2527 2528 2529 2530 2531 2532 2533 2534
Microcontroller based ROBO Car with Major Electronic Components Pic based line following Robot Pic based wall follower Robot Pic Based Edge Detector/Avoiding Robot Pic Based Obstacle Detector /Avoding Robot URDP (Universal Robotics Development Platform)Chassis Wireless Computer Control GolboRobotic Platform Universal Robotic Development Platform - URDP Robotic Arm and Gripper Kit Robot Controller tMECH Kit (OPTO card based Robotic Kit) tBOT Kit (8051 based Robotic Kit) tROBS Kit (AVR based Robotic kit tMICE Kit (Micromouse Assembled Kit) Cell phone Controlled Robots Obstacle Avoiding Robot Wall Follower Robot Edge avoiding robot Object sorting robot based on color without conveyer Vacuum Cleaning robot Pipe Climbing Robot Fire Fighting Robot Pick and Place Robot Robotic for klift Object sorting robot based on color with conveyer Agriculture Robot Spider Robot-Six legged robot Hexapod - Six legged robot Bomb displacing robot with tension controlled soft catching arm
A moving robot control wirelessly to reach the suspected bomb site to relocate the bomb at different place while handling the same carefully by a soft catching arm duly controlled by interrupt monitored motor to avoid extra pressure on the susspected object for safty reasons.
Page29
SCIENCE&TECHNOLOGYPROJECTLIST
2011
2535
2536
2537
2538
War field land Rover that alerts on sensing planted Land Mine ahead
Wirelessly controlled land rover mounted with metal detecting sensors to generate alarms on sensing planted land mine.The movement is wirelessly controlled by a hand held RF transmitter to send commands to the RF receiver mounted on the land rover.
2539
Line following robotic Vehicle that does not require any microcontroller interface or program
An array of two pair of photo sensors comprising IR transmitter and photo diode is fitted in front of the car to detect a black path as well as any turns in the path. By reading the outputs from each of the two sensors, Darlington pair of transistors is biased. Two DC motors are connected to the collector of the transistor TIP122. The motors are able to turn the steering left or right, depending on what logic signal the sensor sends.
2540
A land rover remotely controlled by hand held IR transmitter with flashing LED control
This project uses a robot to extinguish a fire. It is the Robot that can move through any path by IR control and while it is required to face a fire then it extinguishes with help of a Blower fan / or a water pump actuated by the remote. By using IR sensors it can detect the command signals transmitted.
2541
3003 3004
8051 Development Board PIC Burner:-The Programmer for PIC16X8X (With Sample Project of Melody Generator)-0209
This kit contains all the necessary items to build a programmer for PIC16X8X series of micro-controllers. PIC16F83, PIC16C84, PIC16F84 and PIC16F84A are some of the many micro-controller ICs from Microchip technology Inc.
3006
SCIENCE&TECHNOLOGYPROJECTLIST
2011
3007 3008 3009 3010 3011 3012 3013 3014 3015 3016 3017 3018 3019 3020 3021 3022 3501 3502 4501
PIC Development Board PIC Development Board with Programmer PIC Development Board with Programmer and Chassis OPTO Card Rev. 1.0 8051 Development Board Rev 1.2 AVR Development Board Rev 1.2 AVR Daughter Card For UEDP+Programmer Microcontroller Development Board - 8051 Universal Embedded Development Board Cool Runner CPLD Development Platform Spartan III FPGA Development Platform AVR Programmer (with serial cable) Rev 1.1 AVR Programmer (with serial comm.) Rev 1.2 AVR Programmer - USB 8051 Microcontroller programmer - USB 8051 Microcontroller programmer - Serial Interface
AUTOMATION Project
Automatic Wireless health monitoring system in hospitals for patients
Monitoring patient health remotely in hospitals over wireless from the patient bed to the doctors chamber by RF with LCD display at both ends and optionally an alarm on critical situation.
EC
4502
Automatic Bank robbory intimation to Police station with user programmable number
User Programmable telephone number storing by key pad entry enabling auto dial to the police Station or the person concerned in the event of robery.
EC EC / EE
4503
8051
4504
Theft intimation of the vehicle over SMS to owner who can stop the engine remotely
Theft intimaton of the vehicle over sms using GSM modem to the owner while unauthorised door entry is made. Owner can send command through his mobile to stop the engine by activating the relay interfaced to a microcontroller along with the GSM modem used for the purpose.
EC
Page31
SCIENCE&TECHNOLOGYPROJECTLIST
2011
EC / EE
4505
SCADA ( Supervisory Control and Data Acqisition) for remote industrial plant operation
Supervisor sitting on the PC terminal is able to control plant parameters remotely over Rs 232 network while monitoring the data acquired through several sensors.The project uses a front end for the control and a backend with microcontroller interfaced to an ADC from temperature sensors for data collection and control.
4506
EC
4507
Secrecy maintained in parallel connected telephones by enabling only one user at a time
This Project can be used in houses and offices in which more than one telephone is connected in parallel through a single telephone line. The project is used to connect a maximum of four telephones in parallel. When any one of the phone is lifted, all the other lines are disconnected from the telephone line.
EC
4508
EC
4509
EC
4510
Dynamically changing signal light time allotment in street junctions based on traffic density
The project is to solve traffic congestion by a dynamic and automatic traffic light control system based on the traffic density using appropriate system and hardware. IR sensors across the road used to monitor the length of vehicles blocking the road traffic. The signals from the IR receivers are fed to the Microcontroller to follow different time for different level of traffic.
EC / EE
4511
Controlling any house load using DTMF technology through land line or cell phone
The main scope of this project is to send digit commands from one cell phone to be received by another cell phone to receive the tone mode commands which are then DTMF (Dual Tone Multi Frequency) decoded. The receiving cell phone codes are then fed to a microcontroller which is programmed to recognize those codes for operating any kind of load duly interfaced through relay drivers and relays (or motor driver and motor) as per the sent command from senders mobile.
EC / EE
4512
Operating several loads in a multiplex or office from computer through COM port
This project external electrical load applications controlled with the help of PC. PC is connected to microcontroller through MAX 232 level shifter, ULN (Driver) is used to drive the relays for connecting to external devices. DB (RS-232) connector is used to connect to PC com port.
EC / EE
Page32
SCIENCE&TECHNOLOGYPROJECTLIST
2011
EE
4513
Operating house electrical loads like lights and fans using the standard TV remote
A typical TV remote sends certain coded infrared data which is then burnt to a micro controller to drive desired output while same signal is received from an IR receiver interfeced to it.The output from the microcontroller drives the load through relays or opto isolators and triacs. All the buttons of the remote can be used for as much number of loads to be operated.
4514
Automatic door opening system by PIRO Infrared sensor with interrupt monitored motor
Automatic door opening by sensing any approaching human being by piro IR sensors interfaced to a programmed microcontroller that drives a motor through motor driver IC with locked rotor protection some system for door operation.
EC / EE
4515
Railway level crossing gate control through SMS by the station master or the driver
Raiway level crossing gate motor ,controlled by the station master or the engine driver through GSM modem interfeced to microcontroller for deriving an output to dive a relay for the gate motor operation.
EC
4516
Street light intensity control from 100% down to 10% and then off spread over dusk to dawn
White Light Emitting Diode (LED) replaces HID lamps by engaging a programmable microcontroller that controls intensity by pulse width modulation duty cycle which enables energy saving during late nights considering low traffic density.
EE
4517
Automatic alternate supply controller from 4 different sources to ensure no break power
The main scope of the project is to consume the power from supply mains, generator, and wind power and solar optimally by using appropriate programme through microcontroller in most cost effective way.
EC / EE
4518
Programmable logic control ( PLC) for sequentional load setting timing control
Objective is designing a microcontroller based programmable time setting by the user through microcontroller architecture loaded with an application program. Switches are provided for set mode, auto mode , manual mode and time change mode. Machines will run based on/off sequentially in auto mode in default time settings or set mode time setting or manual mode depending on the users need and flexibility.
EC / EE
4519
Preset down counter with relay controlled load for life cycle test
A presetable counter with key pad entry that counts down from the set number till it reaches zero with relay operation connected to a load that switches ON & OFF is used for life cycle test of the gadget under test say a lamp to determine its life.
EC / EE
4520
Precise temperature control for incubators used in hospitals for the pre born child growth
Microcontroller observes temperature readings taken from display unit and compares with the keypad programmed temperature value to control the heater (ON/OFF). Here the controller continuously polls the temperature with certain regular time intervals and displays over the 7_segment display unit for the Microcontroller (Intel 8051) to enable the whole operation by executing the program.
EC
4521
Failed Railway track warning intimation over GSM network to the station master
Damaged or cracked railway track detected by falling loop current interface to micro controller that outputs a signal to a GSM modem for sending a signal to the station master to direct the train driver to stop the train.
EC
Page33
SCIENCE&TECHNOLOGYPROJECTLIST
2011
EC
4522
4523
Sending an SMS for electrical load control that re-sends an acknowledgement of the status
An sms sent through the cell phone to a distant location GSM modem for electrical load interfaced from a micro controller through relay and relay driver to switch on and switch off the same with acknowledgement sent back to the sender on sms upon the action taken and the status of the load.
EC / EE
4524
EC
4525
Large digit display of dialled telephone numbers for std billing centers
Dialed telephone numbers are picked up by a dtmf decoder to feed to a micro controller to drive ten numbers seven segment LED displays for better visibility.
EC
4526
EC
4527
Passenger counter in public transport to alert the driver for excess entry
This application keeps the database of the number of persons entering as well as exiting. 555 timer driven 38 KHz signal from LEDs gets interrupted on to the IR receiver to sense the person entering as well as exiting. This signal is fed to AT89C51 micro controller for analyzing and control purpose with LCD displays on the number of persons in and out.
EC
4528
4529
Micro controller based lamp life extender by ZVS (Zero Voltage Switching) using thyristor
Incandescent lamps exhibit very low resistance in clod condition due to which it draws high current, resulting in failure on switching. Engaging two SCRs in anti parallel or a triac the switching on time can be precisely controlled by firing after detecting the zero cross point of the waveform.
4530
Page34
SCIENCE&TECHNOLOGYPROJECTLIST
2011
4531
A microcontroller based control of current source converter fed reversing induction motor drive by remote control. Ideal for exhaust fans to throw air out and bring air in by remote as desired
The controller receives the Infrared Signal from the IR remote, the code of which is identified by the receiver that switches on/off the appropriate triac for a split phase induction motor to achieve desired direction.
4532
Biometric access control by thumb identification and access to secured area (Sensor on hire)
The project identifies the employees over the campus by a thumb impression by which each and every employee in the campus is identified. Whenever the thumb impression is matched with the inbuilt identification then the display would allow the entry together with an output to actuate a lamp or optionally a motor for gate operation purposes. By this way we can keep official security at doorstep.
4533
Portable coded wireless message communication between two parties secretly with LCD display
The aim of the project is to send encrypted text message transmitted through RF by using Micro Controller and received at receiver which is decrypted by another Micro Controller where message is displayed over the LCD display. Transmitter gets data from a standard computer keyboard and encrypts with a private algorithm. At receiver end the Micro controller decrypts it with the same algorithm and displays the data on LCD.
4534
4535
4536
4537
4538
Page35
SCIENCE&TECHNOLOGYPROJECTLIST
2011
4539
4540
4541
Mathematical Manipulation of Pure Sine Wave Inverter using microcontroller to develop adaptive PWM (pulse width modulation) to achieve the same instead of traditional square wave output
PWM technology is implemented using Signet SG 3524/ a microcontroller for switching from 12 volt DC through a half bridge MOSFET(Z-44) power devices connected to the main inverting transformer that delivers the out put through a RC filter to get appropriate wave and fairly regulated +- 2% AC output having overload / over voltage control by crow bar mechanism control. Depending on the circuit chosen, the output is in the form of sine wave.
4542
Monitoring Serial Communications in MC Based Embedded Systems using CAN, Control Area Network. Three microcontrollers communicating with each other over pair of wire
As the number of microcontrollers embedded in a product increases the solution for communication among them preferred serially. The paper describes a message based monitoring tool using the RS232 Rx Tx bus features of the MC to communicate between 3 MCs.
4543
4544
LED based street light with programmable intensity control using solar power from photovoltaic cells
LED based street light with programmable intensity control using solar power from photovoltaic cells and a programmable microcontroller fed to a Mosfet for varying intensity during late nights automatically.
4545
4546
4547
Page36
SCIENCE&TECHNOLOGYPROJECTLIST
2011
4548
4549
4550
4551
4552
4553
4554 4555
4556
4557
4558
4559
4560
4561
Page37
SCIENCE&TECHNOLOGYPROJECTLIST
2011
4562
4563
4564
4565
4566
4567
4568
4569
4570 4571
4572
4573
4574 4575
Page38
SCIENCE&TECHNOLOGYPROJECTLIST
2011
4576
4577
4578
4579
4580
Page39