Académique Documents
Professionnel Documents
Culture Documents
Enter service mode (SP) --HoId the (C/S) Button for 4 seconds then enter 1 --- O ----7 --- (C/S),
Exit service mode: by pressing (C/S) three times.
Reset fuser and some other error codes by Enter SP 5-810 and select 1 press and hold photomode key while
holding photomode key press (#) key
Failing polygon (SC320) motor usually caused by overheating because of defective cooling fan.SC503/504 tray
Lift motor malfunction (SC503,5O4) First check for paper behind the trays otherwise open the combined lift
motor of the paper tray unit and you will see one of the wires from the liftmotor is broken from the contact.
Enter service mode (SP) --HoId the (C/S) Button for 4 seconds then enter 1 --- O ----7 --- (C/S),
Exit service mode: by pressing (C/S) three times.
Reset fuser and some other error codes by Enter SP 5-810 and select 1 press and hold photomode key while
holding photomode key press (#) key
Enter service mode(SP): Press the clear mode key. enter 1-0-7 hold down the c/s for three seconds.
To enter the special service mode hold the # key down while pressing Copy SP.
Reset fuser and some other error codes by Entering the sp mode and cycling the power.
RICOH AP3800/828 – GESTETNER DSc38 -
SAVIN SLP38c
CODICE DESCRIZIONE
SC195 Serial Number Mismatch
SC201 Polygon motor
SC220 Synch. detection signal error 1 (001: Y), (002: M), (003: C), (004: K)
SC221 Synch. detection signal error 2 (001: Y), (002: M), (003: C), (004: K)
SC230 FGATE error: (001: Y), (002: M), (003: C), (004: K)
SC231 FGATE Timeout: (001: Y), (002: M), (003: C), (004: K)
SC240 LD over (001: Y), (002: M), (003: C), (004: K)
SC260 LD HP sensor not switched on (for K only)
SC261 LD HP sensor not switched on (for K only)
SC285 Line position adjustment (MUSIC) error
SC370 TD sensor (K): Adjustment Error
SC371 TD sensor (Y): Adjustment Error
SC372 TD sensor (C): Adjustment Error
SC373 TD sensor (M): Adjustment Error
SC374 Vt error (K)
SC375 Vt error (Y)
SC376 Vt error (C)
SC377 Vt error (M)
SC380 K dev. motor error
SC381 Color dev. motor error
SC385 ID sensor VSG adjustment
SC386 Development gamma error (K)
SC387 Development gamma error (Y)
SC388 Development gamma error (C)
SC389 Development gamma error (M)
SC390 Development Bias output
SC391-01 Charge AC: output error
SC460-001 Thermistor 1(open circuit)
SC460-002 Thermistor 1(short circuit)
SC461-001 Thermistor 2 (open circuit)
SC461-002 Thermistor 2 (short circuit)
SC471 transfer belt H.P.
SC490 Transfer bias paper attraction roller bias leak
SC501 Paper Tray 1
SC502 Paper Tray 2
SC503-01 Tray 3 error (Paper Feed Unit or LCT)
SC501-02 Tray 3 error (Paper Feed Unit or LCT)
SC504-01 Tray 4 error
SC504-02 Tray 4 error
SC530 Fusing fan
SC541 Heating roller thermistor
SC542 Heating roller warm-up error
SC543 Heat roller Iamp overheat
SC544 Heating roller fusing Iamp 10w temp
SC545 Heat roller Iamp Short
SC546 Heat roller fusing Iamp temperature fluctuation
SC551 Pressure roller thermistor
SC552 Pressure roller warm-up
SC553 Pressure roller fusing Iamp over temp
SC554 Pressure roller fusing Iamp Iow temp
SC555 Pressure roller fusing Iamp short
SC556 Pressure roller fusing Iamp temp fluctuation
SC560 Zero cross
SC621 Finisher/mailbox communication
SC622 Bank communication
SC623 Duplex unit communication
SC640 BCU - Controller communication
SC641 BCU —Controller communication
SC670 No response from BCU at power on
SC680 BCU/ MUSIC communication
SC687 Memory address command
SC722 Finisher jogger motor
SC724 Finisher staple hammer motor
SC725 Finisher stack feed-out motor
SC726 Finisher shift tray 1 Iift motor
SC727 Finisher stapler rotation motor
SC729 Finisher punch motor
SC730 Finisher stapler motor
SC731 Finisher exit guide plate motor
SC732 Finisher tray 1 shift motor
SC733 Finisher tray 2 Iift motor
SC734 Finisher tray 2 shift motor
SC818 Software
SC835 Centronics interface
SC836 Font ROM
SC837 Font ROM
SC850 Network interface
SC851 EEE 1394
SC860 HDD
SC861 HDD
SC863 HDD
SC864 HDD
SC865 HDD
SC900 Electroctronic counter error
SC990 Defective software
SC998 Application start error
RICOH AFICIO 180/150
CODICE DESCRIZIONE
SC122 Scanner home position
SC320 Polygon motor
SC322 Laser Sync Error
SC402 High Voltage Leak Transfer or Charge
SC542 Fuser warm up error
SC543 Fuser over temp
SC544 Fuser Iow temp
SC546 Fuser temp. not steady
SC547 Zero cross signal POSS: power supply, Fuser ground strap touching Iamp
SC620 Communication error between BICU & ADF.
SC691 Communication error between BICU and Fax
SC901 Counter error --check fuse #4
Fuser reset procedure: SP5-810 select 1, press and hold the photo mode key and then press and hold
the enter key and wait for 5 beeps.
0-00 DIS or NSF not detected - Check connections to fax pcb and BICU
0-21 EOL signal from other end not received: change G3 switch 0A bit 4 to a 1
A4 fax print on two pages: set printer switch 03, bit 0 to 1 and printer switch 04 to 00111111
Envelope ard bypass printing - set paper in user tools/printer/job control/paper input /bypass/standard
APS through ADF, reads wrong size - Clean Sliding electrodes on bottom of DF
Enter service mode (SP): Press the clear mode key. enter 1-0-7 hold down the c/s for three seconds.