Académique Documents
Professionnel Documents
Culture Documents
Revell Ju52 3m Transport
Revell Ju52 3m Transport
85562400200
JUNKERS Ju 52 / 3m TRANSPORT
Originally developed and used as a peacetime commercial airliner, the Ju52 made its maiden flight in 1932. At the start of World War II, when Germany invaded Poland, the Luftwaffe's Transportverband had an inventory of 547 Ju52/3ms. The Ju52 was taylor-made to supply fast moving troops and advanced paratrooper deployment, the Ju52 was a real "workhorse".
READ THIS BEFORE YOU BEGIN * Study the assembly drawings. * Each plastic part is identified by a number. * In the assembly drawings, some parts will be marked by a star () to indicate chrome plated plastic. * For better paint and decal adhesion, wash the plastic parts in a mild detergent solution. Rinse and let air dry. * Check the fit of each piece before cementing in place. * Use only cement for polystyrene plastic. * Scrape plating and paint from areas to be cemented. * Allow paint to dry thoroughly before handling parts. * Any unused parts may be discarded. DECAL APPLICATION INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. Cut desired decal from sheet. Dip decal in water for a few seconds. Place wet decal on paper towel. Wait until decal is movable on paper backing. Place decal in position on model, face up and slide backing away. Press out air bubbles with a soft damp cloth. Milkiness that may appear is for better decal adhesion and will dry clear. Wipe away any excess adhesive. Do not touch decal until fully dry. Allow the decals 48 hours to dry before applying clear coat. 1. 2. 3. 4. 5. 6. 7. 8. 9.
LIRE CE QUI SUIT AVANT DE COMMENCER * Etudier les schmas de montage. * Chaque pice en plastique est identifie par un numro. * Sur les schmas de montage, certaines pices sont marques d'une toile () pour indiquer qu'elles sont en plastique chrom. * Pour une meilleure prise de la peinture et des autocollants, laver les pices en plastique avec une solution dtergente peu concentre. Les rincer et les laisser scher l'air. * Vrifier que chaque pice s'ajuste bien avant de la coller en place. * N'utiliser que de la colle pour polystyrne. * Gratter les parties coller pour enlever le chrome et la peinture. * Laisser la peinture bien scher avant de manipuler les pices. * Toute pice inutilise peut tre jete. DIRECTIVES D'APPLICATION DES AUTOCOLLANTS Dcouper l'autocollant dsir de la feuille. Tremper l'autocollant dans de l'eau pendant quelques secondes. Placer l'autocollant mouill sur une serviette en papier. Attendez que l'autocollant puisse tre dplac sur son support en papier. Mettre l'autocollant en position sur le modle face sur le dessus et faire glisser le support pour l'enlever. Appuyer avec un chiffon doux humide pour liminer les bulles d'air. La substance laiteuse qui peut apparatre est destine amliorer l'adhsion de l'autocollant et devient incolore au schage. Essuyer pour enlever tout excdent d'adhsif. Ne pas toucher l'autocollant tant qu'il n'est pas bien sec. Laisser l'autocollant scher pendant 48 heures avant d'appliquer une couche transparente. REMARQUE: Les autocollants sont compatibles avec les solutions de fixage ou les solvants.
This paint guide is provided to complete this kit as shown on the box.
Ce guide de peintures est fourni pour reproduire le modle rduit qui apparat sur la bote.
Black Green Dark Green Flat Black Light Gray Light Olive Green Yellow Flat White Gray Gunmetal Steel Flesh Tan Light Blue
Vert noir Vert fonc Noir mat Gris clair Gris vert Jaune Blanc mat Gris Bronze Acier Chair Havane Bleu clair
If you have any questions or comments, call our hotline at: (800) 833-3570 or, please write to: Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007 Be sure to include the plan number (85562400200), part number, description, your return address and phone number.
Visit our website: www.revell.com
Revell Inc Elk Grove Village, IL. Copyright 2009. All rights reserved.
1
47 FUSELAGE FLOOR
GRAY
67 CONTROL YOKE
66 CONTROL COLUMN
GRAY
66 COLUMN
GRAY
65 CONSOLE
1 DECAL
64 INSTRUMENT PANEL
uSE thE point of A ModEling knifE to opEn up All holES which ArE indicAtEd on thE BottoM of thE pArt. thErE ArE A totAl of ElEvEn holES to BE opEnEd.
48A TABLE
GRAY
135 WINDOW
CLEAR
49 BULKHEAD 50 BULKHEAD
GRAY GRAY
25 HANDRAIL
GRAY
48 BULKHEAD
GRAY
61 CO-PILOT'S SEAT
60 PILOT'S SEAT
52 GUNNER'S FLOOR
GRAY
51 BULKHEAD
GRAY
55 SEAT
54 HANDRAIL
GRAY
NOTE: GLUE FUSELAGE FLOOR ASSEmbLy TO THE FUSELAGE SIDE FIRST, THEN ATTACH HANDRAIL. LADDER AND SEATS
53 BENCH SEATS
56 SEAT LEGS
GRAY
58 SEAT
59 SEAT LEGS
GRAY
63 HANDLE
GRAY
134 CRANK
GRAY
53 BENCH SEATS
GRAY
26 TAIL WHEEL
4
NotE: oPEN UP thE hoLES iN thE FUSELAgE BottoM For thE MiLitArY AND AMBULANCE VErSioNS AS iNDiCAtED iN thiS DrAWiNg. oPEN UP thE tWo PANELS AS iNDiCAtED For thE MiLitArY VErSioN oNLY. SEE StEPS #9 AND #10 For oPtioNAL LANDiNg gEAr ASSEMBLiES
FUSELAgE BottoM
REMOVE THESE TWO PANELS FOR THE MILITARY VERSION ONLY MILITARY AMBULANCE
3 FUSELAGE BOTTOM
82 EXHAUST COLLECTOR
STEEL
137 HOIST
GRAY
FLAT BLACK
69 RADIO
OPEN HOLE
OPEN HOLE
FUSELAGE ASSEMBLY
7
7 RIGHT WING TOP
WING ASSEMBLY
6 LEFT WING TOP
WINGS TO FUSELAGE
8
LEFT
STABLIZER ASSEMBLY
103 LEFT ELEVATOR
RIGHT
8
LEFT
STABLIZER ASSEmBLy
RIGHT
CONTINUED
24 STRUT
24 STRUT
9
LEFT
33 OUTER MAIN WHEEL 29 LEFT MAIN STRUT
ASSEmBLy
33 OUTER MAIN WHEEL 30 RIGHT MAIN STRUT
RIGHT
106 RIGHT AFT STRUT 30A BRACKET
29A BRACKET
RIGHT
93 RIGHT INNER WHEEL COVER 97 RIGHT REAR STRUT
33 OUTER MAIN WHEEL 32 INNER MAIN WHEEL 101 LEFT MAIN GEAR STRUT
33 OUTER MAIN WHEEL 32 INNER MAIN WHEEL 102 RIGHT MAIN GEAR STRUT
101A BRACKET
102A BRACKET
98 GUN MOUNT
GRAY
78 MACHINE GUN
GUNMETAL
RETRACTED POSITION
EXTENDED POSITION
96 BUCKET 96 BUCKET
12
MARK THESE LOCATIONS ON THE BACK SIDE OF THE CYLINDERS BEFORE ASSEMBLING THE ENGINE.
FLAT BLACK
36 COVER
GRAY CRANKCASE
FRONT
BACK
STEEL
13
MARK THESE LOCATIONS ON THE BACK SIDE OF THE CYLINDERS BEFORE ASSEMBLING THE ENGINE.
FLAT BLACK
36 COVER
GRAY CRANKCASE
FRONT
BACK
NOTE: THE OPEN SPACE ON THE COVER FITS TO THE BOTTOM OF THE CYLINDERS.
14
RIGHT
15
MARK THESE LOCATIONS ON THE BACK SIDE OF THE CYLINDERS BEFORE ASSEMBLING THE ENGINE.
FLAT BLACK
36 COVER
FRONT
BACK NOTE: THE OPEN SPACE ON THE COVER FITS TO THE BOTTOM OF THE CYLINDERS.
39 INTAKE MANIFOLD
STEEL
NoTE: oNE ENd oF THE PaRT (82a) FITs INTo THE boTTom HolE oN THE REaR oF THE CylIINdERs. THE oTHER ENd FITs INTo THE EXHausT CollECToR WHICH Was GluEd To THE uNdERsIdE oF THE FusElaGE IN sTEP (5). aNy sEPaRaTIoNs IN THE EXHausT PIPEs CaN bE FIllEd WITH INsTaNT GluE.
EXHAUST COLLECTOR
uNdERsIdE VIEW sHoWING PRoPER loCaTIoN FoR all PaRTs aFTER assEmbly
16
11 LEFT FLAP
uNdERsIdE assEmbly
80 PUSH RODS 80 PUSH RODS
10 RIGHT FLAP
16
UNDERSIDE ASSEMBLY
44 OIL COOLER INTAKE FILTERS
FLAT BLACK
CONTINUED
13 ANTENNA SUPPORT
FLAT BLACK
12 ANTENNA
17
131 PUSH ROD 130 INDICATOR
TOpSIDE ASSEMBLY
143 INDICATOR 72 ANTENNA 73 GENERATOR 74 RIGHT LOOP ANTENNA 75 LEFT LOOP ANTENNA
130 INDICATOR
35 PROPELLERS
PAINT BLADES BLACK-GREEN PAINT CENTER SECTIONS FLAT BLACK
34 PITOT PROBE
STEEL
18
final assembly
111 CANOPY
CLEAR
79 MAGAZINE
FLAT BLACK
78 MACHINE GUN
GUNMETAL
77 GUN SUPPORT
GRAY
117 SHIELD
CLEAR
76 GUN RING
GRAY
81 GUN SEAT
GRAY
116 WINDOW
CLEAR
28 LADDER
GRAY
27 DOOR
19
89 RIGHT ARM
paratroopers assembly
91 PARACHUTE 90 LEFT ARM 84 RIGHT ARM 86 PARACHUTE 121 BODY 125 PARACHUTE 126 BODY 129 PARACHUTE
122 LEGS
tHe German paratrooper Uniform inClUDeD a tan pUlloVer WitH meDiUm Gray pants anD blaCK boots. tHe Helmets Were a steel Gray, anD tHe paraCHUte paCKs Were UsUally neUtral or liGHt Gray WitH flat WHite straps anD steel bUCKles. tHe faCes anD HanDs sHoUlD be painteD a flesH Color.
20
DECAL PLACEMENT
21
DECAL PLACEMENT
22
decal placement