Académique Documents
Professionnel Documents
Culture Documents
INCH-POUND
MS28774M
23 APRIL 2009
SUPERSEDING
MS28774L
19 NOVEMBER 1990
DETAIL SPECIFICATION SHEET
RETAINER, PACKING BACKUP, SINGLE TURN, POLYTETRAFLUOROETHYLENE
Inactive for new design after 25 MARCH 1989.
This specification sheet is approved for use by all Departments and Agencies of the
Department of Defense.
The requirements for acquiring the product described herein shall consist of this
specification sheet and procurement specification SAE AS8791.
A
W
M
(SEE NOTE 4)
G GAP
(SEE NOTE 5)
ENDS TO BE
PARALLEL TO
CENTER LINE 5
T
FIGURE I. Retainer.
AMSC N/A
FSC 5330
MS28774M
!M
.001
.109
.124
.140
.171
.202
.234
.265
.327
.390
.455
.518
.580
.643
.705
.768
.830
.898
.960
1.023
1.085
1.148
1.210
1.273
1.335
1.398
MS28774-110
MS28774-111
MS28774-112
MS28774-113
MS28774-114
MS28774-115
MS28774-116
MS28774-117
MS28774-118
MS28774-119
MS28774-120
MS28774-121
MS28774-122
MS28774-123
MS28774-124
MS28774-125
MS28774-126
.390
.452
.515
.577
.640
.702
.765
.832
.895
.957
1.020
1.082
1.145
1.207
1.270
1.332
1.397
.052
.045
.054
.052
.005
.000
.087
.085
.006
.000
A"
39 +0 -4
33 +0 -3
30 +0 -3
26 +0 -3
22 +0 -3
MS28774M
TABLE I. Part Numbers and Dimensions. - continued
PART
NUMBER
MS28774-127
MS28774-128
MS28774-129
MS28774-130
MS28774-131
MS28774-132
MS28774-133
MS28774-134
MS28774-135
MS28774-136
MS28774-137
MS28774-138
MS28774-139
MS28774-140
MS28774-141
MS28774-142
MS28774-143
MS28774-144
MS28774-145
MS28774-146
MS28774-147
MS28774-148
MS28774-149
!M
.001
1.459
1.522
1.584
1.647
1.709
1.772
1.834
1.897
1.959
2.022
2.084
2.147
2.209
2.258
2.320
2.383
2.445
2.508
2.570
2.633
2.695
2.758
2.820
MS28774-210
MS28774-211
MS28774-212
MS28774-213
MS28774-214
MS28774-215
MS28774-216
MS28774-217
MS28774-218
MS28774-219
MS28774-220
MS28774-221
MS28774-222
.766
.828
.891
.953
1.016
1.078
1.141
1.203
1.266
1.334
1.397
1.459
1.522
MS28774-223
MS28774-224
MS28774-225
MS28774-226
MS28774-227
MS28774-228
MS28774-229
MS28774-230
1.647
1.772
1.897
2.022
2.147
2.272
2.397
2.522
.052
.045
.087
.085
.006
.000
.120
.118
.007
.000
A"
22 +0 -3
MS28774M
TABLE I. Part Numbers and Dimensions. - continued
MS28774-231
MS28774-232
MS28774-233
MS28774-234
MS28774-235
MS28774-236
MS28774-237
MS28774-238
MS28774-239
MS28774-240
MS28774-241
MS28774-242
MS28774-243
MS28774-244
MS28774-245
MS28774-246
MS28774-247
!M
.001
2.631
2.756
2.881
3.006
3.131
3.256
3.381
3.506
3.631
3.756
3.881
4.006
4.131
4.256
4.381
4.506
4.631
MS28774-325
MS28774-326
MS28774-327
MS28774-328
MS28774-329
MS28774-330
MS28774-331
MS28774-332
MS28774-333
MS28774-334
MS28774-335
MS28774-336
MS28774-337
MS28774-338
MS28774-339
MS28774-340
MS28774-341
MS28774-342
MS28774-343
MS28774-344
MS28774-345
MS28774-346
MS28774-347
MS28774-348
MS28774-349
1.513
1.638
1.763
1.888
2.013
2.138
2.268
2.393
2.518
2.643
2.768
2.893
3.018
3.143
3.273
3.398
3.523
3.648
3.773
3.898
4.028
4.153
4.278
4.403
4.528
PART NUMBER
.052
.045
.120
.118
.007
.000
.075
.065
.184
.182
A"
22 +0 -3
MS28774M
TABLE I. Part Numbers and Dimensions. - continued
PART
NUMBER
MS28774-425
MS28774-426
MS28774-427
MS28774-428
MS28774-429
MS28774-430
MS28774-431
MS28774-432
MS28774-433
MS28774-434
MS28774-435
MS28774-436
MS28774-437
MS28774-438
MS28774-439
MS28774-440
MS28774-441
MS28774-442
MS28774-443
MS28774-444
MS28774-445
MS28774-446
MS28774-447
MS28774-448
MS28774-449
!M
.001
4.551
4.676
4.801
4.926
5.051
5.176
5.301
5.426
5.551
5.676
5.801
5.926
6.051
6.274
6.524
6.774
7.024
7.274
7.524
7.774
8.024
8.524
9.024
9.524
10.024
MS28774-450
MS28774-451
MS28774-452
MS28774-453
MS28774-454
MS28774-455
MS28774-456
MS28774-457
MS28774-458
MS28774-459
MS28774-460
10.524
11.024
11.524
12.024
12.524
13.024
13.524
14.024
14.524
15.024
15.524
.110
.100
.237
.235
.008
.000
A"
22 +0 -3
.010
.000
Notes:
1. Material shall be in accordance with procurement specification: SAE AS8791.
2. Surfaces must be smooth and free from irregularities. Edges must be clean and sharp.
3. Dimension A in degrees, all other in inches.
4. For use in packing grooves conforming to MIL-G-5514.
5. In measuring dimensions !M over a mandrel, the scarf cut shall not exceed dimension G and
no overlap permitted beyond the full scarf.
MS28774M
6. For parts 140-149, 231-247, 438-460, it is recommended that the respective dash sizes under
MS27595 (not cut) be used when possible.
7. For design purposes, this standard takes precedence over procurement specification referenced
here-in.
8. Changes from previous issue. Marginal notations are not used in this revision to identify changes
with respect to the previous issue due to the extent of the changes.
Custodians:
Army - MR
Navy - AS
Air Force 99
Preparing Activity:
DLA -IS
(Project 5330-2009-009)
NOTE: The activities listed above were interested in this document as of the date of this document.
Since organizations and responsibilities can change, you should verify the currency of the
information above using the ASSIST Online database at http://assist.daps.dla.mil.