Académique Documents
Professionnel Documents
Culture Documents
Features :
2:1 wide input range Protections: Short circuit / Overload / Over voltage / Over temperature 1500VAC I/O isolation Cooling by free air convection 100% full load burn-in test 24V and 48V input voltage design refer to LVD 2 years warranty
SPECIFICATION
MODEL DC VOLTAGE RATED CURRENT CURRENT RANGE RATED POWER OUTPUT VOLTAGE ADJ. RANGE VOLTAGE TOLERANCE Note.3 LINE REGULATION LOAD REGULATION SETUP, RISE TIME VOLTAGE RANGE INPUT EFFICIENCY (Typ.) DC CURRENT (Typ.) INRUSH CURRENT (Typ.) OVERLOAD PROTECTION OVER VOLTAGE OVER TEMPERATURE WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS SAFETY & WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC (Note 4) EMI CONDUCTION & RADIATION EMS IMMUNITY MTBF OTHERS
NOTE
300ms, 50ms at full load C:36 ~ 72VDC 82% 85% 86% 6.7A/48V 86% 5A/48V
105 ~ 135% rated output power Protection type : Shut down o/p voltage, re-power on to recover 5.75 ~ 6.75V 16.8 ~ 20V 31.5 ~ 37.5V 53 ~ 65V Protection type : Shut down o/p voltage, re-power on to recover 95 5 (100 5 5.75 ~ 6.75V 16.8 ~ 20V 31.5 ~ 37.5V 53 ~ 65V
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down -20 ~ +60 (Refer to output load derating curve) 20 ~ 90% RH non-condensing -40 ~ +85 , 10 ~ 95% RH 0.03%/ (0 ~ 50 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes UL60950-1approved (for SD-200C-24 type only), IEC60950-1 CB approved by TUV (for D type only) I/P-O/P:1.5KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 Compliance to EN55022 (CISPR22) Class B 218.2K hrs min. MIL-HDBK-217F (25 215*115*50mm (L*W*H) 1.1Kg; 12pcs/14.4Kg/0.92CUFT ) / 70% RH
DIMENSION PACKING
1. All parameters NOT specially mentioned are measured at 24,48,96VDC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to EMI testing of component power supplies. (as available on http://www.meanwell.com)
1.888.612.9514
www.trcelectronics.com/meanwell
Features :
2:1 wide input range Protections: Short circuit / Overload / Over voltage / Over temperature 1500VAC I/O isolation Cooling by free air convection 100% full load burn-in test 24V and 48V input voltage design refer to LVD 2 years warranty
SPECIFICATION
MODEL DC VOLTAGE RATED CURRENT CURRENT RANGE RATED POWER OUTPUT VOLTAGE ADJ. RANGE VOLTAGE TOLERANCE Note.3 LINE REGULATION LOAD REGULATION SETUP, RISE TIME VOLTAGE RANGE INPUT EFFICIENCY (Typ.) DC CURRENT (Typ.) INRUSH CURRENT (Typ.) OVERLOAD PROTECTION OVER VOLTAGE OVER TEMPERATURE WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS SAFETY & WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC
(Note 4)
105 ~ 135% rated output power Protection type : Shut down o/p voltage, re-power on to recover 5.75 ~ 6.75V 16.8 ~ 20V Protection type : Shut down o/p voltage, re-power on to recover 85 5 (TSW1) detect on main power transistor 31.5 ~ 37.5V 53 ~ 65V
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down -20 ~ +60 (Refer to output load derating curve) 20 ~ 90% RH non-condensing -40 ~ +85 , 10 ~ 95% RH 0.03%/ (0 ~ 50 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes IEC60950-1 CB approved by TUV (for D type only) I/P-O/P:1.5KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC / 70% RH
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B EMS IMMUNITY MTBF 218.2K hrs min. MIL-HDBK-217F (25 215*115*50mm (L*W*H) 1.1Kg; 12pcs/14.4Kg/0.92CUFT )
OTHERS
DIMENSION PACKING
NOTE
1. All parameters NOT specially mentioned are measured at 24,48,96VDC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to EMI testing of component power supplies. (as available on http://www.meanwell.com)
1.888.612.9514
www.trcelectronics.com/meanwell
Mechanical Specification
117.5 32.5 27.5 19 LED +V ADJ. 9 8 7 6 5 4 3 2 1 150 177.5
Unit:mm
135 9.5
95 50
8.3
15 32.5 13 max. 25 50 C L
115
6-M4 L=6mm
Block Diagram
I/P EMI FILTER RECTIFIERS & FILTER FILTER POWER SWITCHING RECTIFIERS & FILTER
fosc : 100KHz
+V -V
PWM CONTROL
DETECTION CIRCUIT
Derating Curve
Static Characteristics
Ta=25
100
others
100 90
80
80
60
LOAD (%)
LOAD (%)
40
70 60 50 40
20
-20
10
20
30
40
50
60
(HORIZONTAL)
24 48 96
36 72 144
AMBIENT TEMPERATURE (
1.888.612.9514
www.trcelectronics.com/meanwell