Académique Documents
Professionnel Documents
Culture Documents
(13888.9) (6944.4)
20000 10000
(3472.2)
5000
56640 28320
14160
200 100 50
20 10 5
(1.4) (0.7)
2 1 1 2 (6.9) (13.8) 5 (34.5) 10 (69) 20 (138) 50 (345) 100 (690) 200 (1380) 500 (3450) 1000 (6900)
FLOWING PRESSURE - PSIG (kPa) High Range Standard Range Low Range
Flow rates are at standard conditions of 14.73 psia and 60 F and are based on 100% methane gas @ 0.6 s.g.
Specifications
Size: Flow Range: End Connections: Working Pressure: Test Pressure: 2 in. (50.8 mm) 10:1 to 15:1 (see graph) Flowmeter installs between two raised face flanges 0 to 2220 psig (15,306 kPa) 3330 psig (22,960 kPa) Conduit Connection: Pressure Tap: Compliances: 1-in. (25.4 mm) 1/8 in. NPT (3.2 mm) CSA Certified Hazardous locations Class I, Group A, B, C, D, Div. 1 Body materials comply with recommendations of NACE MR01-75 Materials of Construction: Body and Cartridge: Bearing Mounts: Bearings: Rotor: Rotor Shaft: Pickup Extender: Set Screws: Pressure Port Plug: Flow Straightener Tube Bundle (optional): Grade 316L stainless steel Grade 304 stainless steel Tungsten Carbide Grade 455 stainless steel Tungsten Carbide Grade 430 stainless steel Grade 304 stainless steel Grade 304 stainless steel Grade 321 stainless steel, carbon steel, or Grade 316 stainless steel
Nominal Calibration Factor: Low Range Standard Range High Range Output Frequency: Output Voltage: Pressure Drop: Linearity: Repeatability: Temperature: Pickup Connector: 325 p/ACF (16600 p/m3) 125 p/ACF (4415 p/m3) 70 p/ACF (2472 p/m3) 5 to 320 Hz over rated range 30 MV peak to peak at 5 Hz 900 MV peak to peak at 320 Hz Less than 1-in. (24.5 mm) water column at maximum rated flow +/- 2% of reading +/- 0.5% of reading 0 to 225 F (-18 to 107 C) Mates with AN3106A-10SL-4P
Installation Diagram
Gasket 1.8 Gasket
Temperature Well
INLET
Straightening Vanes 5 Nominal Pipe Diameters Centering Rings Gas turbine Meter
Gas Turbine Flowmeter 2 in. (50.8mm) Two Bladed Tungsten Carbide, vee type
A) Through bolts and centering rings (specify flange rating) B) Stainless steel tube bundle, Grade 321 C) Upstream flow section, 2 in. (50.8mm) standard weight pipe with flange one end (specify rating), other end beveled for welding, carbon steel, with Grade 321 stainless steel tube bundle D) Mating connector for pickup
Companion readout instruments for NuFlo turbine flowmeters are also available.
NuFlo
North America:
Measurement Systems
Singapore: Bognor Regis, UK:
For representation in your area:
65.6737.0444
singapore@nuflotech.com
44.1243.826741
uk@nuflotech.com
Shreveport, LA Houma, LA Lafayette, LA Laurel, MS Bakersfield, CA Saginaw, MI Casper, WY Broomfield, CO Dallas, TX Tulsa, OK
Canada: Calgary, AB Edmonton, AB International: Jakarta, Indonesia Aberdeen, Scotland Bognor Regis, UK
www.nuflotech.com
4