Académique Documents
Professionnel Documents
Culture Documents
Close Window
Assessment System Exam Viewer - Chapter 3 Exam - IT Essentials: PC Hardware and Software (Version 4.1)
Below you will find the assessment items as presented on the exam as well as the scoring rules associated with the item. Cisco Networking Academy content is copyrighted and the unauthorized posting, distribution or sharing of this exam content is prohibited. 1 A technician is installing a new power supply in a computer. Which type of power connector should be used to connect to a PATA hard drive? Berg mini-Molex Molex 20-pin ATX connector
Max Value 2
A technician is installing a new power supply in a computer. Which type of power connector should be used to connect to a floppy drive? Berg Molex 20-pin ATX connector SATA connector
Max Value 2
A technician is assembling a new computer. Which two components are often easier to install before mounting the motherboard in the case? (Choose two.) CPU memory NIC sound card video card
Description Option 1 and Option 2 are correct. 1 point for each correct option. 0 points if more options are selected than required.
Max Value 2
Which solution should be used to clean a CPU and a heat sink? soap and water rubbing alcohol a diluted ammonia solution isopropyl alcohol
Max Value 2
When building a computer, which two components are normally installed in 3.5-inch drive bays? (Choose two.) hard drive optical drive
netacad.net//exam_viewer.shtml?
1/5
02/03/2011
floppy drive flash drive video card
Description Option 1 and Option 3 are correct. 1 point for each correct option. 0 points if more options are selected than required.
Max Value 2
Max Value 2
A technician is troubleshooting a computer that has a malfunctioning floppy drive. The technician observes that the floppy drive light remains lit constantly. How should the technician attempt to repair the problem? Remove the floppy drive using Add/Remove Hardware. Replace the floppy drive. Connect the data cable making sure that the colored stripe on the cable is aligned with pin 1 on the drive and the motherboard. Change the jumper setting to master for the floppy drive.
Max Value 2
What is a convenient way that a technician can tell whether a ribbon cable is for an IDE hard drive or a floppy drive? The IDE cable has a colored stripe on one edge. The floppy cable motherboard connector is normally gray. The IDE cable is gray. The floppy cable has a twist in the cable.
Max Value 2
A field technician has been asked to install a wireless 802.11g NIC in a computer, but is unsure about the expansion slots available. Which two types of wireless NICs should the technician have available? (Choose two.) PCIe AGP SCSI PCI SATA
Description Option 1 and Option 4 are correct. 1 point for each correct option. 0 points if more options are selected than required.
Max Value 2
10 Which port is typically used for external wireless NICs? Parallel PS/2 SCSI USB
netacad.net//exam_viewer.shtml?
2/5
02/03/2011
Observable 1 correctness of response
11 Which additional 4-pin or 6-pin power connector is required by some motherboards? AUX Berg Parallel SCSI
Max Value 2
12 A technician is installing a new CPU in a ZIF socket on a motherboard. What is the primary way of securing the CPU in place? thermal compound antistatic fasteners load lever screws
Max Value 2
13 Which type of drive is installed in a 5.25-inch bay? hard drive optical drive floppy drive LS120 drive
Max Value 2
14 After a technician has assembled a new computer, it is necessary to configure the BIOS. At which point must a key be pressed to start the BIOS setup program? before the computer is powered on during the Windows load process during the POST after the POST, but before Windows starts to load
Max Value 2
15
netacad.net//exam_viewer.shtml?
3/5
02/03/2011
Max Value 2
16 What is the most reliable way for users to buy the correct RAM to upgrade a computer? Buy RAM that is the same color as the memory sockets on the motherboard. Ensure that the RAM chip is the same size as the ROM chip. Ensure that the RAM is compatible with the peripherals installed on the motherboard. Check the motherboard manual or manufacturer's website. Refer to the exhibit. Which type of hard drive uses the power connector shown? Observable 1 correctness of response Description 2 points for Option 4 0 points for any other option Max Value 2
17
Refer to the exhibit. Which type of port is shown? FireWire graphics RJ11 RJ45 USB
Max Value 2
18 A technician has just finished assembling a new computer. When the computer is powered up for the first time, the POST discovers a problem. How does the POST indicate the error? It issues a number of short beeps. The LED on the front of the computer case flashes a number of times. It places an error message in the BIOS. It locks the keyboard.
Max Value 2
netacad.net//exam_viewer.shtml?
4/5
02/03/2011
19 Which action is recommended to prevent the motherboard from contacting the metal base of the case? Ensure that the non-conductive side of the case is beneath the motherboard. Use standoffs to keep the motherboard above the metal base. Place a non-conductive barrier between the motherboard and the metal base. Use a self-adhesive non-conductive membrane on the underside of the motherboard.
Max Value 2
20 Which internal component of a computer uses a 3-pin power connector? floppy drive hard drive sound card fan
Max Value 2
Reset View
Showing 1 of 1 Prev Page: 1 Next
Close Window
All contents copyright 2001-2010 Cisco Systems, Inc. All rights reserved. Privacy Statement and Trademarks.
netacad.net//exam_viewer.shtml?
5/5