Académique Documents
Professionnel Documents
Culture Documents
MAIN MCU
3.3V C9 104 P1.0 P1.1 P1.2 P1.3 P1.4 P1.5 P2.0 P2.1 P2.2 1 2 3 4 5 6 7 8 9 10 U1 VCC GND P1.0 XIN TXD XOUT RXD TEST P1.3 RST P1.4 SDA P1.5 SCL P2.0 P2.5 P2.1 P2.4 P2.2 P2.3 20 19 18 17 16 15 14 13 12 11 P2.6 P2.7 TEST RST P1.7 P1.6 P2.5 P2.4 P2.3 S1 1 2 4 3 XTAL select SW-dip SW S1 ON to connect to external crystal
C5, C6 & Y1 as close to U1 as possible C5 XIN NP Y1 XOUT 32.768Khz Crystal C6 NP C5, C6: ceramic capacitor NP = not populated R5 47K J16 1 2 3 2-wire Jtag header 3 C10 1n (102): ceramic capacitor SW4: two-pin button GND TEST RST RST
ADC MODULE
J3
TRANSISTOR MODULE
5V R12 1k
header 2 For ADC module: + Pin1 connects to 3V3 + Pin 2 connects to ADC channel
D13 LED J18 transitor R13 1 header 1 Transistor, TO-92 package 2k7 Q1 Q2SC1815
3.3V
BUTTON MODULE
3.3V R6 47K BT1
C10 1n
R7 47K BT2
C12 104
SW3
COMMUNICATION PORT
P1.6 P1.7
NOTEs
For PCB design (layout) instructions, schematic details, components introdution and BOM, visit: www.PayItForward.edu.vn/wordpress/tutorials/orcad/mach-msp430/ For footprint library (*.LLB) downloading, visit: www.PayItForward.edu.vn/wordpress/tutorials/orcad/
1 2 3
3.3V
LED MODULE
R11 1 2 3 4 5 6 7 8 9
1 2 3
P1.1 P1.2
For OrCAD tutorials (Capture and Layout), visit: www.PayItForward.edu.vn/wordpress/tutorials/orcad/ For more discussion about the board MSP430G2553 DEV., visit: www.PayItForward.edu.vn/forum/forums/83/
D5 D6 D7 D8 D9
EXTENDED PORT
J6 PORT 2 header 8 1 2 3 4 5 6 7 8 P2.0 P2.1 P2.2 P2.3 P2.4 P2.5 P2.6 P2.7 J9 PORT 1 header 8 1 2 3 4 5 6 7 8 P1.0 P1.1 P1.2 P1.3 P1.4 P1.5 P1.6 P1.7 J15 SPI 1 2 3 4 5 P1.4 P1.5 P1.6 P1.7 STE: P1.4 CLK: P1.5 SOMI: P1.6 SIMO: P1.7
D12
This schematic was designed for beginners who will lay out the PCBs by themselves. This board is used for pratising OrCAD and learning MCU MSP430G2553 from Texas Instruments. Was designed and published by PIF club, Aug., 2012.
AC1 J1 1 2 1 2 2 -
5V U3 L1117-3v3 Vin C2 100u/16V C4 104 SW1: Switch 3-pin 3-position 1 2 D2 3 LED blue SW1 3v3 select R2 470 D3 LED green J11 D1 --> D4: 3mm or 5mm LEDs If Use 3v3 from Launch Pad 1 2 3v3 launchpad R3 470 Title Revision v1rev4 Size B Date: Designer Document Number R10 470
A
3.3V
GND
OUT
D1 LED
GND
OUT
3v3 regulator
C7 22u/16V
C8 104
R1 1K
POWER SUPPLY
3v3 Launch Pad Header 2
PIF.MSP430G2553.DEV.
PIFer.TXHN
Saturday, August 04, 2012 Sheet
1
1 1 of 1