Vous êtes sur la page 1sur 5

Water Level Indicator Description This is the circuit diagram of a simple corrosion free water level indicator for

home and industries. In fact the the level of any conductive non corrosive liquids can be measured using this circuit. The circuit is based on 5 transistor switches. Each transistor is switched on to drive the corresponding LED , when its base is supplied with current through the water through the electrode probes. One electrode probe is (F) with 6V AC is placed at the bottom of tank. Next probes are placed step by step above the bottom probe. When water is rising the base of each transistor gets electrical connection to 6V AC through water and the corresponding probe. Which in turn makes the transistors conduct to glow LED and indicate the level of water. The ends of probes are connected to corresponding points in the circuit as shown in circuit diagram.Insulated Aluminum wires with end insulation removed will do for the probe. Arrange the probes in order on a PVC pipe according to the depth and immerse it in the tank.AC voltage is use to prevent electrolysis at the probes. So this setup will last really long. I guarantee at least a 2 years of maintenance free operation. Thats what I got and is still going. Components T1 T5 BC 548 or 2N2222 Transistors R1-R5 2.2K 1/4 W Resistors R6-R10 22K 1/4 W Resistors D1 D5 LEDs ( color your choice) Notes: Use a transformer with 6V 500 mA output for power supply. Do not use a rectifier! we need pure AC. Use good quality insulated Aluminum wire for probes. If Aluminum wires are not available try Steel or Tin.Copper is the worst. Try the circuit first on a bread board and if not working properly, make adjustments with

the resistance values. This is often needed because conductivity of water changes slightly from place to place. The type number of the transistors used here are not critical and any small signal NPN transistor will do the job. Few other suitable type numbers are BC546, BC107, PN2222, BC337, BF494, ZTX300, BEL187 etc. The circuit can be enclosed in a plastic box with holes for revealing the LEDs . Water Level Indicator Circuit Diagram and Sensor Arrangement.

Water Level Indicator

If you need a fully automatic water level controller circuit then try this circuit Water level controller. The circuit is fully based primarily on transistors. The sensing section is somewhat similar to this circuit but there is additional circuitry for switching the pump ON when the water level falls below a set level and the pump will be switched OFF when the tank is full. Few transistors , one 555IC and an electromagnetic relay is used for realizing the control section. The circuit is very simple cost effective , reliable and many guys have successfully assembled it.I am also working on a float type water level indicator/controller using the float type fuel gauge mechanism used in motor cycles.
Ic 7404: Pin configuration of ic7404 is as shown in below.Ic7404 is NOT gate circuit it has 6 NOT gates in it. NOT gate1: input: pin1 output: pin2 NOT gate2: input: pin3 output: pin4 NOT gate3: input: pin5 output: pin6

NOT gate4: input: pin9 output: pin8 NOT gate5: input: pin11 output: pin10 NOT gate6: input: pin13 output: pin12

Pin 7: ground pin14: +Vcc Ic 7408: Pin configuration of ic7408 is as show belowIc7408 is a 2input nand gatesIt has 4 nand gates in it.

AND gate1: input pins:1,2 outputpins:3

AND gate2: input pins:4,5 outputpins:6 AND gate3: input pins:9,10 outputpins:8 AND gate4: input pins:12,13 outputpins:11Pin 7: ground pin 14: +VccThe ciruit is constructed using these two ics (ic7404,ic7408) and the sevent segment displaysthe circuit is as shown below

How it works: This water-level indicator uses a 7-segment display, instead of LEDs, to indicate the water level(low, half and full) in the tank. Moreover, a buzzer is used to alert of water overflowing from thetank. The circuit shows the water level by displaying L, H and F for low, half andfull, respectively. The circuit uses five sensors to sense the different water levels in the tank.Sensor A is connected to the negative terminal (GND) of the power supply. The other four sensors (B through E) are connected to the inputs of NOT gate IC 7404. When there is a highvoltage at the input pin of the NOT gate, it outputs a low voltage. Similarly, for a low voltage atthe input pin of the NOT gate, it outputs a high voltage. When the tank is empty, the input pins of IC 7404 are pulled high via a 1-mega-ohm resistor. So it outputs a low voltage. As water starts filling the tank, a low voltage is available at the input pins of the gate and it outputs ahigh voltage.

When the water in the tank rises to touch the low level, there is a low voltage atinput pin 5 of gate N3 and high output at pin 6. Pin 6 of the gate is connected to pin 10 of gate N9, so pin 10 also goes high. Now as both pins 9 and 10 of gate N9 are high, its output pin 8 alsogoes high. As a result, positive supply is applied to DIS3 and it shows L indicating low level of water in the tank. Similarly, when water in the tank touches the half level, pins 4 and 5 of AND gate N8 become high. As a result, its output also goes high and DIS2 shows H indicating half level of water in the tank. At this time, pin 9 of gate N9 also goes low via gate N4 and DIS3stops glowing. When the water tank becomes full, the voltage at pin 1 of gate N1 and pin 3 of gate N2 goes low. Output pin 3 of gate N7 goes high and DIS1 shows F indicating that thewater tank is full. When water starts overflowing the tank, pin 13 of gate N6 goes low to makeoutput pin 12. The buzzer sounds to indicate that water is overflowing the tank and you

need toswitch off the motor pump.We can Assemble this circuit easily on a general-purpose PCB and we can enclose it in a suitable box. we can Use a non-corrosive material such as steel strip for the five sensors and hang themin the water tank as shown in the circuit diagram.We can use 5v power supply or 5v adapter as +Vcc Advantage: i)No need to waste time to observe the water level time to time, ii) Wastage of water can be prevented iii)By using automatic switches instead of alarms we can turn off them automatically, sowe can make its switching off completely independent of human Disadvantage: We cant completely depend on these circuits because if any of probes which are atmaximum level or the probe which is at bottom level gets disconnected or broken it will notfunction correctly. So we have to provide security to it.

Vous aimerez peut-être aussi