Académique Documents
Professionnel Documents
Culture Documents
Overhaul
COMMERCIAL
Indianapolis, Indiana 46206
ENGINE
BULLETIN
July 30, 1976 TURBINE, GAS PRODUCER SUPPORT AND NO. 8 BEARING RETAINING PLATE- REWORK PLANNING INFORMATION: EFFECTIVITY: All Series I and II turbine (engine) assemblies prior the following turbine (engine) serial numbers: Model 250-Cl8 250-C20 Turbine Serial No. CAT 23649BC
CAT 38352P
to
excluding CAT 38349P 250-C20B 250-B15G 250-B17 250-B17B REASON: CAT 33301 CAT 50100 CAT 60063P CAT 80188
CAE 823247 through 823264 CAE 830298 CAE 850100 CAE 870060 CAE 880185
The No. 8 bearing retaining plate is located circumferentially in the turbine gas producer support by a slot which engages with 0.060 in. high dowel pin in the support. During turbine reassembly, it is possible to misindex the retaining plate so that it is seated on top of the support dowel pin. When this occurs, the cocked retaining plate prevents the sump and nut assembly from properly compressing its metallic gasket. To prevent the possible misindexing of the bearing retaining plate, P/N 6871412, 6871452, and P/N 6878427 Gas Producer Supports are reworked by replacing AN122683 or MS9390-08 Dowel Pin with P/N 6894196 Revision No. 3 Offset Pin, April 21, 1978 Rolls-Royce Proprietary Data Uncontrolled Printed Copy
DESCRIPTION:
COMMERCIAL
ENGINE
BULLETIN
TURBINE, GAS PRODUCER SUPPORT AND NO. 8 BEARING RETAINING PLATE--REWORK Also, P/N 6871564 Bearing Retaining Plate slot is widened and deepened to fit with the new offset pin. If the bearing retaining plate is not properly indexed and seated, the length of the new offset pin prevents the threads of the sump and nut assembly from engaging the threads in the gas producer support. Following rework, the gas producer support and bearing retaining plate are reidentified. INTERCHANGEABILITY: The gas producer supports which incorporate the new P/N 6894196 0ffset Pin may be used only with P/N 6895005 Bearing Retaining Plate. COMPLIANCE: APPROVAL: MANPOWER: MATERIAL Part No. 6894196-l 6894196-2 6894196-3 6894196-4 6894196-5 TOOLING: It is recommended thatthis bulletin be accomplished no later than next overhaul following parts availability. FAA-DER Approved. will be required to complete this
Approximately 1.5 man-hours bulletin at time of overhaul. AVAILABILITY: Nomenclature Pin, Pin, Pin, Pin, Pin, None OTfset Offset Offset Offset Offset (0,094 (0.096 (0.099 (0.104 (0.109 in. in. in. in. in. Dia. ) Dia. ) Dia.) Dia.) Dia. )
WY. 1 AR AR AR AR
WEIGHT AND BALANCE: Not affected. REFERENCES: ATW-2035 R evision No. 3 April 21, 1978 Published July 30, 1976
COMMERCIAL
ENGINE
BULLETIN
ACCOMPLISHMENT I.
INSTRUCTIONS:
Rework P/N 6871412, 6871452, and 6878427 Gas Producer Supports as follows (Figure 1):
A.
B.
Remove AN122683 or MS9390-08 Dowel Pin from the support. Add 0.04 x 45 chamfer at the existing pin hole. Select P/N 6894196-1 , -2, -3, -4 or -5 Stepped Pin for drive fit. Install stepped pin flush with the support as shown in Figure 1. Obliterate
AS478-2Dl
C.
D.
the existing part number and reidentify or 2E as follows: Old Part No.
6871412 t I 6871452 6878427
per
Model
250-Cl8 250-B15G 250-C20 250-B17 250-C20B 250-B17B
II.
A.
B.
Remachine the existing 0.125 in. wide pin slot to the new dimensions shown in Figure 2. Obliterate the existing part number and reidentify as
6895005 per AS478-2Dl.
III.
Record compliance with CEB-187 (C18), CEB-1091 (C20/C20B), TP CEB-41 (B15G), or TP CEB-1065 (B17/B17B) in the Turbine Assembly (pink pages), Modification Record, Part III of the Engine Log Book. Revision No. 3 April e&l978 Published July 30, 1976
Rolls-Royce Proprietary Data Uncontrolled Printed Copy
COMMERCIAL
ENGINE
BULLETIN
SECTION AJ-AJ
GAS PRODUCER
SUPPORT 1
REWORK
FIGURE
TP
COMMERCIAL
ENGINE
BULLETIN
LVIEWA -fi* .
NOTES: 1. TOL. ON ANGLESzt lo 2. TOL. ONTHREEPLACEDECIMALSdI.DlO 3. FINISH ALLOVER '2lUOS 4. BREAKSHARPEDGES0.010 UOS
BEARING RETAINING FIGURE
FORM 7347 - 1
PLATE 2
February
Rolls-Royce Proprietary Data Uncontrolled Printed Copy
25, 1977
>Julv 30- 19?6
Published
Page6
COMMERCIAL
ENGINE
BULLETIN
TURBINE, GAS PRODUCER SUPPORT AND NO. 8 BEARING RETAINING PLATE--REWORK MATERIAL INFORMATION: Dis-
&ty. Nomenclature
1 1 1 1 AR AR AR AR 1
Old P/N
6871412 6871452
Qty.
position A A A B
Support Assy, Turbine-Gas Producer (Cl8 and B15G) Support Assy, Turbine-Gas Producer (C20 and B17) Support Assy, Turbine-Gas Producer (C20B and B17B) Pin (0.094 in. Pin (0.096 in. Pin (0.099 in. Pin (0.104 in. Pin (0.109 in. Dia. )
Dia. )
1
1
6895010
6894196-1 6894196-2 6894196-3
6878427
AN122683
1 1
6894196-4 6894196-5
6895005
MS;;90-08
6871564
Stock Disposition A. B.
Revision
No. 3