Académique Documents
Professionnel Documents
Culture Documents
U.S. RIFLE
INTRODUCTION
1. Purpose and Scope the care, cleaning, and handling of each weapon
and its ammunition.
a. This manual is B guide for commanders and b. Marksmanship training is wwxed in FM 23-
instructor in presenting instruction in the’me- 71 and FM 23-16.
chanical operation of the Ml4 and M14E2 riflea c. The material contained herein is applicable
It include+ B detailed description of the rifle and without modification to both nuclear and nonnu-
its general chuactaristics; procedures for detailed clear warfare.
disassembly and assembly; an explanation of func- d. Users of this manual are encouraged to sub-
tioning; a discussion of the types of stoppages and mit recommended changes or comments to improve
the immediate action applied to reduce them; a de- the publication. Comments should be keyed to
scription of the ammunition; and instructions on the specific page, paragraph, and line of the text
NET STUD
TRIGGER GUARD
SLING
in which the change is recommended. Reascms (4) The lug on the rear of the flash suppins-
should be pnwidsd for each comment to insure un- sor is used to secure a bayonet, B grenade
denstanding and complete evaluation. Comments launcher, and B blank firing attachment.
should be forwarded direct to the Commandant, (5) The spindle valve is used when launching
United States Army Infantry School, Fort Rsn- a grenade to prevent gas operation of the
ning, cfa, 31265. rifle, thus avoiding damage to the weapon.
b. Ml.&% RijEe.
2. Impertrmm of Mechanical Training (1) The U.S. rifle, 7.62mm, M14E2 (Iig. 3)
is an air-cuoled, gas-operated, magazine-
Therifleis the Infantryman’s basic weapon. It fed, shoulder weapon. It is capable of
gives him an individual and powerful capability
semiautomatic or automatic fire; how-
for combat. To benefit the most from this caps;
ever, it is designed primarily for auto-
bility, the Infantryman must develop two skills to
matic fire. It features a stabilizer assem-
an equal degree: he must be able to fire his weapon
bly, modified bipod, front and rear hand-
well enough to get hits on battlefield targets, and
grip, straight line stock, and & rubber
he must lmow enough about its working parts to
recoil pad.
keep it operating. The Infantryman attains his
(2) The M14E2 stock group is the “straight
firing skill in mwksmanship training. He learns
line” type with a fixed rear handgrip and
how to keep his rifle in operable condition through
a folding front hsnderin which lies flat
mechanical training.
along the bottom of the stock when not
in use. The location of the front hand-
3. Descriptionof lho Rifles
grip csn be adjusted to one of five posi-
a. Ml4 R@!e. tions in l-inch increments to wxommo-
(1) The U.S. rifle, 7.62mm, Ml4 (fig. 1) is date all gunners The rubber reooil pad
B lightweight, air-cooled, ga+opsrated, reduces the effects of recoil. The hinged
magazine-fed, shoulder weapon. It is de- shoulder rest provides vertical control of
signed primarily for semiautomatic fire. the butt end of the rifle. The butt swivel
(2) When employed as an automatic rifle, the pivots 26” to the left for ease of carrying.
selector and biped hi2 must be installed The stabilizer assembly consists of a per-
(fig. 2). forated steel sleeve which slides over the
(3) The flash suppressor is designed with a flash suppressor and is fastened to the
wide rib on the bottom to reduce muzzle muzzle over the bayonet lug by a screw
climb and t.he amount of dust raised by and 8 locknut. The stabilizer provides
muzzle blast. muzzle stability and reduces recoil.
,.:.,_,. ,.._
SELECTOR
3
(4) The M2 biped is modified by the addition the sverage firer, by applying rearward
of a sling swivel and a longer pivot pin pressure on the front handgrip, to in-
to accommodate the swivel. crease the pressure of the biped on the
(5) The M14E2 utilizes a sling with an extra
ground to approximately 35 pounds, I‘B-
hook assembly. The portion of the sling
ducing dispersion considerably. When
between the handgrip and the biped pro-
vides additional muzzle control during the wespon is csrried at sling arms, the
firing. The portion of the sling between sling must be disconnected from the
the front handgrip and the biped sllows handtip assembly.
IFlED EIPOD M2
4
TripgErPull in Pa”&: 5 mi”“tes_______._...._ 40
Minimum____._____________ 5.5 10minutea____.___.__._ 30
Maximum_._____. ____.___.. 7.5 15 mfn”tes_____________ 30
Muzzk veloc&__._.___________ 2,300f.p.s. (853 2Omi”“iez.____. _ 25
m.p.a.). 30 mi”“ta (or more) _ _ _ 20
Cyclic Rote of Fire (round8 per 70&750 Range in Y&n:
minute) Maximum effective (semiau- 460
Ralcs oj Fire. (Them 08” be tomatic, without biped).
maintained without danger to Maximum etrective (semisu- ‘700
the firer, or darmge to the tomatic, witb biped).
wespa) : Maximum effective (autome- **460
Semiautomatic (rounds per tic, with biped!.
minute) : Maximum__._______._______ 3725
1mi”“te______--_._.---
40 Ammunirimt....____.-..-______ see ohspter6.
2mi”“t&3____-._-.---..
40 DqlEndMu:
5mi”“t.m_____-..----.-
30 Cyclicrate____ ___. _.___ ____ themteatwhiobthe
10 mf”“tea_____________ 20 weapon fires auto-
15 mfn”t&3_________._-_ 20 matically.
20 mi”“te._________..._ 20 Maximum effective mmre___.. the aeat& distance
30 mfnutea (or more)__.. 15
Automatic (mu&3 per min-
ute) :
1 miu”te_____.__...____ 60
2 mf”“te___.___..._._ 50
5
CHAPTER 2
MECHANICAL TRAINING
6
safety, tilt the rifle, and look inside the chamber b. Open the trigger guard and place the firing
and receiver to insure that they contain no rounds. mechanism straight down into the receiver, III&-
ing sure that the guide rib on the firing mechanism
enters the recess in the receiver (fig. 9). Place the
7. DisassemblyInto Three Main Groups
butt of the weapon on the left thigh, sights to the
tz.The three main grwps are the firing mecha- left, insuring the triggw guard has cleared the
nism, the barrel and receiver, and the stock. trigger. With the palm of the right hand, strike
b. Aftar the rifle is cleared, the operating parts the trigger guard fully engaging it to the receiver.
should be forward for disaasemblg. To do this,
pull back on the operating rod handle and allow
thebolttogoforward
C. To remove the Siring mechanism, grasp the
rear of the trigger gusrd with the thumb and fore-
finger of your right hand and pull downward and
outward until the mechanism is released (fig. 6).
Lift out the firing mechanism.
d. To mparata the barrel and rwaiver from the
stock, lay the weapon on a flat surface with the
sights up and muzale to the left. Grasp the re-
ceiver with the left hand over the rear sight and
hrise the rifle L few inches. With the right hand,
strike down on and grasp the small of the stock,
mpnrating the barrel and receiver from the stack.
The thm main groups are shown in figure 7.
e. The oompcwmta of the M14E2 rifle am shown
in Iigure 8.
LJ \
FIRING MECHANISM
c
i
BARREL AND RECEIVER GRbUP
BARREL AND RECEIVER GROUP
STABILIZER ASSEhdLY
M2
17wo w--2 9
6. RipGField Sttipped. The partsof the bar- amy from pm. Hold the bolt by the roller and
rel and rweiver group in their order of disassem- locking lug and place the rear of the bolt on the
bly aareshown in figure 15. bridge of the receiver, firing pin tang pointed
down. Turn the bolt slightly cmntmolockwise
until the tang of the firing pin clears the bridge_
10. Assembly of the Barrel and Receiver Guide the left locking lug of the bolt into its groove
hvP on the left side of the receiver. Lower the right
a. Re$&.ng ths Lb!& Place the barrel and 1~ locking lug on its bearing surfam and slide the
.caiver on the table, sighta up, muzzle pointing bolt halfway to the rear.
. I..
Y
10
‘-
I/ Figure14. RemMthg theb&t.
b. Repl&~ the Operating Rod. Holding the hole in the guide can be alined with the connector
operating rod at t,he handle, place the front end lock. Lower the guide and push the connector
into t.he operating rod guide, and position the rod lock in with the right thumb (fig. 16).
so that the rcce~~ in the hump fits over the bolt d. Rep7min.g the Conntwtoi- Assembly. Place
roller. Turn the operating md to the left until the barrel and receiver on its side with the oper-
the guide lug fits into the disassembly notch on the ating rod handle up, muzzle away from you.
Placa the elongated hole in the rear of the con-
receiver, then move the operating rod forward
nector assembly on the elongated stud on the scar
until the bolt is closed.
release (1, fig. 17). Place the thumb of the right
c. Replan’ng the Operating Rod Sprnq and
hand on the rear of the connector assembly, the
Operating Rm-2Spring &.%e. Turn the barrel
first finger on the sear release bracket, and the
and receiver over so the sights are down and the
second finger inside the rear of the receiver.
muzzle is to the left. Place the operating red Pushing toward the muzzle with the right ,thumb
spring guide into the operating rod spring, hump and with the thumb and first finger of the left
up, and feed the lease end of the spring into the hand, turn the front of the connector counterclcck-
operating rod. Grasp the spring and guide with wise until it can be snapped onto the connector
the left hand and compress the spring until the lock (2, fig. 17).
11
CONNECTOR ASSEMBLY OPERATING ROD
OPEtiATlNG ROD -
SPRING GUIDE
OPERZTING ROD
SPRING
.~._..-
BARRELAND RECEIVER
I2
11. Disassemblyof the Gas System and
13
.
Q i
Jl
t t
FRONT BAND HAND GUARD
I
GAS CYLINDER GAS &sT~N GAS CYLINDER GAS CYLII;DER
PLUG LOCK
b. Gas Sya&n. Slide the gas cylinder rsarward tion tool (fig. 21). Slide the combination tool
&rough the front band. Tighten the gas cylinder over the head of the 8crew and place it ovsr the
lock by hand to its fully sssemblsd position, then locknut.
back it off until the loop is alined with the gae cyl-
inder. Replace the gas pi&on with the flat part
15. Disassembly of the Magazine
toward the barrel and the open end toward the
muzzle. when the gas piston is properly seated, a. Use a pointed objs& to raise the rear of the
it will protrude one and one-half inchas below the magazine base (6g. 22) until the indsntation on
gas cylinder (fig. IQ). Replace the gas cylinder the base is clear of the magazine. Grasp the maga-
plug and tighten it securely with the wrench of zinc with either hand, with one finger of the hand
the combination tool. wwxing the base. Remove the base and guide
the spring, one coil at a time, to clear the retain-
13. Removing the Stabilizer Assembly of ing lips of the magazine.
b. Remove and sepwpsrstethe magazine spring
the M14E2 Ritle
and follower. Figure 23 shows the parts of the
To remove the stabilizer asssmbly, u9e the magazine.
mnch end of the combination tool to loosen the
l&nut. Then slide the combination tool over
16. Assembly of the Magazine
the screw and loown it Swing the yoke away
from the bayonet lug, and slide the stabilizer as- Reposition the spring inside the follower with
sembly off the flssh supprewx (Cg. 20). the rectangular-shaped end of the spring sgainst
the rear of the follower, and replace the follower
and spring inside the magazine. Be sure to fully
14. Replacing the Stabilizer Assembly of
seat the follower. Replace the magazine base (fig.
the M14E2 Riie
24).
To replace the stabilizer 8898m211yslide it over
the Aash supp-r, swing the yoke over the bay-
onet lug, and tightan the screw with the combina-
14
15
. .... ,..v..-~~5”‘,..-.. , .-.
.__ .~ I, .,.
STABILIZER ASSEMBLY
16
17
CHAPTER3
OPERATIONAND FUNCTIONING
Section 1. OPERATION
17. loading the Magazine (Out of the R&l b. A magazine in the weapon can he loaded
through the top of the receiver with a K-round
u. Place each round on top of the magazine
cartridge clip. To do thii placa either end of the
follower (with the bullet end toward the front of
clip in the cartridge guide, then exert pressure
the magazine) end apply pressure with the thumb
with the thumb or the open end of the combination
to fully eeat the round in the magazine (fig. 25).
tool on the top round, forcing 5 rounda into the
b. To load the magazine, with B I-round car-
megazme (fig. 2.8). Remove and diecard the car-
tridge clip, the mega.zine filler is used (f& 26).
tridga clip. Repeat the proceea until the maga-
Slide the filler over the top rear portion of the
zine is loaded.
magazine and insert L 5-round cartridge clip into
the filler. Place either the thumb or the open end
19. loading and Unloading the RiRe
of the combiiation tool on the top round and push
the 5 rounds into the magazine. Remove the clip a. Place the saf&y in the cafe. position.
and repeat the process until 20 rounds have been b. Insert s loaded magazine into the mnguzine
loaded into the magazine, then remove the mega- well, top front first, until the operating rod spring
zinc filler. guide engages the magazine (1, fig. 29)) then pull
backward and upward until the magazine snaps
18. loading the Magazine (in the RiiAe) into position (2, fig. 22). A click will be heard
which indicatee that the magazine is fully eated.
CZ.To load B single round into an empty mega- Pull back and release the operating rod handle,
zinc in the weapon, lock the bolt to the rear and allowing the bolt to strip the top round from the
engage the safety. Place a round on top of the magazine and load it into the chamber.
magazine follower and press down on the round G. Remove the magazine es described in pars-
and fully e& it in the magazine (Cg. 27). graph 6.
19
under pressure of the hammer spring and
strikes the tang of the firing pin, driving
the firing pin against the primer, and fir-
ing the round (fig. 33).
(5) u?&&&q. Unlocking (fig. 34) occurs
after the firing of the round. As the
bullet is forced through the barrel by the
expandii gases, L small amount of gas
enters the hollow gas piston, the gas cylin-
der, and the gas cylinder plug through
the gas porL The expanding geeee force
the gas cylinder piston to the rear. It in
turn drives the operating rod and bolt
rearward. The operating rod came the
bolt roller upward, disengaging the lock-
ing lugs on the bolt from the locking re-
ceersesin the receiver. At this time the
b. The cycle of oper&m is broken down into
bolt is unlocked.
eight staph These tips we listed below, together
with B brief description of what occulg inside the
rifle during each step.
(1) Fw%ng. Feeding takes plsce when a
round is forced into the path of the bolt.
(6) Extmeting. Extracting is pulling the
The top round is forced into the path of
empty cartridge from the chamber.
the bolt by the m&zine follower which
Slow initial extraction takea place as the
in under pressure of the magazine spring
bolt unlocks. The bolt in its rearward
(fig. 30).
motion pulls the empty cartridge with it
(W Chnmheting. Chambering -m-e when (fig.36).
a round is moved into the chamber. This
takes plaoe as the bolt goes forward under (7) Ejecting. Ejecting is removing the
pressure of the expending operating rod empty cartridge from the receiver. As
spring, stripping the top round from the soon es the bolt has withdrawn the empty
magazine and driving it forward into the cartridge case clear of the chamber, the
chamber (fig. 31). Chambwing is corn- force of the ejector spring and plunger
plete when the extractor snaps into the pushes the bottom edge of the cartridge
extracting grcave on the cartridge and base sway from the bolt face, throwing
t,he ejector is forced into the face of the it out and sway from the receiver. When
b-a. the la& round has been fired, the bolt is
held in the rearward position by the bolt
(3) L&&g. Locking begins es the bolt
lC&.
roller engages the camming surface in the
hump of the operating rod. It is corn- (8) Coc,‘&q. Cocking is positioning the
pleted when the locking lugs of the bolt hammer so that it is ready to fire the next
are fully seated in the locking recessa of round. The bolt, as it moves to the rear,
the receiver (fig. 32). forces the hammer down and rides over
(4) Ftinq. Firing occurs when the firing it. The hammer is caught by the near if
pin strikes the primer. As the trigger is the trigger is held to the rear and by the
pulled, the trigger lugs w-e di=ngaged trigger lugs if the trigger has been re-
from the h-er hooks and the hammer leased (fig. 37). In either case, the
is reItwed. The hammer moves forward hammer is held in the cocked position.
21
23
TOP: STANDARD AMMUNITION. SEMIAUTOMATIC AND
AUTOMATIC FIRE.
24
25
21. Automafk (Rii Equips With the sear releaee allows the eaw to move forwad
intO a position where it cau engage the rear Hun-
mer hooks (1, fig. 38). Then, when the bolt drives
o. When thed&r ia positioned with the fwa the hammer to the rear, the sear engages the rear
marked “A” to the rear (ear type projection up), hammer hooks and holds the hammer iu the
cocked position.
the rifle is eat for automatic fire. Turning the CM+
c. After the bolt movee forward end lo&j the
l&r to automatic rotates the eew release iu posi-
shoulder on the operating rod engages the hook
tion to make contsd with the sear.
of the connector aswrnbly and forces it forward.
b. After the first round hae bean fired (and with
This rotates the sear releaee on the selector shaft,
the trigger held to the rear), the operating rod causing the flauge on the sear release to push the
starts its rearward movement under pressure of mer to the rear, disengaging it from the rear ham-
the expanding gases As it mopes to the rear, the mer hooks (2, fig. 33). The hemmer will then go
wunector assembly move rearward under pres- forward if the trigger is held to the rear. If the
sure of the connector arasmbly spring. The move trigger is released at any time prior to the firing
meut of the conuector assembly rot&e the eear of the leet round, the hammer will be held in the
r&a on the eel&or shaft so that the flange on cocked poeition by the trigger lugs.
-
SEAR RELEASE w
ROTATED FORWARD OPERATJNG ROD
STARTED REARWARD
0
SEAR RELEASE
ROTATED REARCARD
ASSEMBLY
--N_/ 01
HAMMER RELEASED
27
CHAPTER 4
29
CHAPTER 5
MAINTENANCE
24. Gemoral
Mamtenanca includes all mea.snrea taken to keep
the rifle in operating condition. This include8
norrnsl cleaning, inspection for defedive parts,
repair, md lubrication.
32
Otherwise, merely wipe the magazine assembly
clean and dry, then oil it.
h. &‘tabdtiwA88emMy. The stabilizer as&?m-
bly should be removed and cleaned with L stiff
brush to remove all carbon or other particles which
may block thegas ports.
i. All Other Parts. Use a dry cloth to remove
all dirt or sand from other parts and exterior sw-
facea. Apply B light coat of oil to the metal parts
and rob TQZD linseed oil into the wooden parts.
as clean as mible. Install the bore cleaning Care must be taken to prevent linseed oil from get-
brush on L section of the cleaning rod. Moisten ting on metal pa&s.
the brush with bore cleaner and clean the interior j. After Firhg. The rifle must b&oroughly
of the piston. Wipe the piston dry, hut do not ~2. cleaned no later than the evening of the day it is
The gas system incorporates * self-clesning s=ec- fired. For three consecutive days thereafter, check
tion and functions within very close tolerances. for evidence of fouling by running a clean patch
A piston does not have to be shiny to function through the bore and inspecting it. The bore
properly. Do not use abkwea to ckan the piston. shonld be lightly oiled after each inspection.
e. Face of the Bolt. Clean the face of the bolt
with B patch and bore cleaner, paying particular 27. Nom101 Maintenance
attention to its inside edgw. Remove the bore a. The rifle should be inspected daily, when in
cleaner with dry patches and oil the part lightly. use, for evidence of wet and general ~ppearanee.
f. Spindle Valve. Depress the valve and rotati A light coat of oil should be maintained on all
it several times after each day’s firing. Do not dis- metal part+ except the gas piston, interior of the
llssemble it. gas cylinder, and the gas plug.
g. Maga.&w. Inspect the interior of the maga- b. The daily inspection should also reveal any
eine by depressing the follower with the thumb. defects such 85 burred, worn or cracked parts.
If the interior is dirty, di saasemble the magazine Defects should be reported to the armorer for car-
and clean it, then lightly oil the component parts. &ion.
34
35
SCREW THE PATCH HOLDER OFF THE ROD
INSERT THE ROD. LESS THE PATCH HOLDER.
GENTLY INTO THE BORE. ALL THE WAY
a6
3
Figure 4#-42mthned.
UGHSORE
WITH AXIS
THE MUZZLE
3
Fcoffs 46-c.mtinued.
37
c. A mnzzle plug should never be used on the knob can be turned without extreme
rifle. It causes moisture to collect in thebore form- diftioulty (1, fig. 47).
ing rust and creating B safety hazard. (6) If the elevation knob is extremely loom
d Obtaining the proper rear sight tension is and the rear sight aperture will not
extremely important; without it, the sight will not raise, the w&&zqe knub nut must be
hold its adjustment in elevation. During normal turned in L oZoc~&e direction, one
maintenance, and prior to firing, the rear sight click at s time, until the aperture can
must be checked for correct sight tension. The beraised
indications of improper sight tension are: (c) To check for proper tension, the pm
(1) Elevation knob extremely difficult to turn.
cedurea listed below should be fol-
(2) Elevation knob turns freely without an
lowed :
audible click.
(a) If the elevation knob is extFemelg diffi-
1. Raise the aperture to its full height.
L Lower the aperture two clicks.
cult to turn, rotate the &n&ge bob
nut counterclc&wise one click et a time 3. Grasp the rifle with the &gem around
with the screwdriver portion of the the small of the stock and exert
combination tool. Altar each click at- downward pressure on the aperture
tempt to turn the t&u& knob. Re- with the thumb of the same hand
pat this pnxesa until the e7azwtion (2, fig. 47).
(d) If the qwture drape, sight tension be used if nary to remove oil or greasa Parta
must be adjusted. To do this, the that show signs of wear may be wiped with a patch
wi&aqe knob nwt must be turned in lightly dampened with lubricating oil (LAW).
L clockwise direction, one clicE at a It is best to keep the rifle aa close as pwsible to
time, until the ap-&ure can no longar outside temperatures at all times to prevent the
be pushed down aa indicated in (c).9 collection of moisture which ocoure when cold
above. If the proper tension cannot be metal comes in contact with warm air. When
obtained, the rifle mu& be turned in to the rifle is brought into a warm room, it should
the unit armorer. not be cleaned until it haa reached room tempera-
ture.
28. Special Maintenance d. In hot, humid cliiatpe or if exposed to salt
a. Before firiug the rifle, the bore and the cham- water or salt water atmosphere, the rifle mu& be
her should be cleaned and dried. A light coat of inspected thoroughly each day for moisture and
oil should be placed on all other metal parts, rust. It should be kept lightly oiled with special
except those which come in contact with ammuni- preservative lubricating oil. Raw linseed m7
tion, the gas piston, interior of the gas cylinder, should be frquently applied to the wooden parts
and the gas plug. to prevent swelling.
b. Pafore firing, rifle grease should be applied e. In hot, dry climates, the rifle must be cleaned
to the parts indicated in figure 40. A smell daily or more often to remove sand and/or dust
amamt of grease ia taken up on the stem of the from the bore and working psrte. In sandy areas,
grearw container cap and is applied at each plea the rifle should be kept dry. The muzzle and re-
Rifle - is wt used in extremely cold tempers- c&a should be kept covered during eand and
turn or when the rifle is exposed to extremes of dust storms. Wooden parts must be kept oiled
sand nnd dust. with 1ycu)l&seed oi2 to prevent drying. The rifle
a In cold cliiataa (temperatures below freez- should be lightly oiled when sand or dust condi-
ing) the rifle mus& be kept free of moisture and tions decrease.
exeea oil. Moisture and excem oil on the working f. Special instructions on caring for the rifle
parta cr~umthem to operate sluggishly or fail mm- when it is subject to nuclear, biological or chemi-
pletely. The rifle must be disassem bled and wiped cal contamination CM be found in TM 3-220 and
with a dean dry cloth. Drycleaning solvent may FM 21-40.
CHAPTER 6
AMMUNITION
ACCESSORIES
42
Ftmw.9 51. InrtalkUton of MS WM.
43
BAYONETLUG
37. Ml2 Blank Firing Attachment and M3
deflector shield and a guide lug with spring
Breech Shield
plunger.
The blank firing attachment and breech shield
a. znӦta2kztion (fig. 58).
(fig. 57) are deigned for usa when firing blank
(1) Bla& firing attmhmmt.Insert the ori-
cartridges. The blank firing attachment, which
fica tube in the muzzle opening of the flash
eecura the attachment to the bayonet lug of the
supprawx. Pull out on the clip latch
flash mppresor,consists of an orifice tube and a
and push down on the top of the orifice
spring clip latch. The breech shield, which se- tube of the blank firing attachment.
curp~ ihe shield to the cartridge clip guide, is used lease the clip spring latch securing Re the
with the blank firing attachment and consists of B cut away portion of the latch to thebayo-
net lug.
45
~tgwe 56. IsMUatt.m
of 1111.5g+enode hither stqht.
REFERENCES
49
By@rderofthe,l!kadqoftheArmy:
HAROLD R. JOHNSON,
Gene&, U&a? St&s Amy,
05oid : Chiaf of staff,
J. C. LAMBERT,
Major Benend, U&&d b’ta.k%Amy,
The Adjutant Gensral.
Dl&rlbotlon:
AotW Army:
DcSPmt (2) UMCO?dD (1) YFSS (1)
DCSPE (Zj USACDO (2i USA0C.W (1)
ACM (2) Armen (25) USAQME (1)
DSCLDQ (2) carg (2) USASCS (1)
DCSOPS (2) Dir (10 USACHS (1)
COB0 (2) Dm Ar’W (5) USAEIS (1)
CBD (1) Bde (5) USATSOE (1)
WA (1) Beet (5) USACBfLCS f 1)
CINm (1) QP (1) USASESCS (1)
TIo (1) BG (5) USMA (2)
TJAOSA (1) CC (5) src ckalm (5)
CNQB (2) Bn (5) MI1 Mm3 (1)
ACSFDB (2) CwBtw (5) USATC (10) except
USiXINARO (6) Br SW SC?.(5) except USATC Inf (26
ABADcmM (2) USAMPS (1)
ABADCOM BIIn (1)
NQ: Slata AG (3) ; nnita-eame PP Active Amy except alhvmce is Cow cqMen to each unlt.
VEAR: Udtwame aa Actire Army except alkmvanee is two cwlea to each unit.
For arpluytion d abbreviatIrrm wed, ee AB 22&50,
50