Académique Documents
Professionnel Documents
Culture Documents
Bus Interface
5V RS-485/RS-422 Half-Duplex
Transceiver
High-Performance Low Voltage
UARTs with 16/32/64-Byte FIFOs
DataCom
Single-port 10/100/1000Base-T
Gigabit Transceiver
Development Tools
Nu Horizons
Inrevium
Xilinx
LED Lighting
Logic
Wireless
March 2009
High-Performance Low Voltage UARTs
with 16/32/64-Byte FIFOs
Bus Interface
Smallest and Fastest Single-Channel
Universal Asynchronous Receiver
Transmitter (UART) Series
The XR16M58x/68x/78x series are part of the enhanced Universal
Asynchronous Receiver and Transmitter (UART) family with 16, 32
and 64 bytes of transmit and receive FIFOs. These devices have
selectable or programmable transmit and receive FIFO trigger levels,
automatic hardware and software flow control, and compatible with
the Intel, Motorola, or VLIO bus interface.
Features Benefits
Intel, Motorola or VLIO Bus Interface Highest Performance at Lower Supply Voltages
20Mbps Maximum Data Rate Overall System Cost Reduction
Selectable or Programmable TX/RX trigger levels Shorter Time-to-Market
VCC VCC
PwrSave PwrSave
(1. 62 to 3. 63 V) (1.62 to 3.63 V)
A2:A0 LLA#
GND GND
D7:D0 TX AD7:AD0 TX
IOR# BRG 64 Byte TX FIFO IOR# BRG 64 Byte TX FIFO
IOW# (R/W#) TX , RX, TX, RX,
IOW#
UART RTS #, CTS #, UART RTS#, CTS#,
CS# IR TX & CS# IR TX &
DTR #, DSR#, DTR#, DSR#,
Regs ENDEC RX ENDEC RX
INT/IRQ# RI #, CD # Regs RI#, CD#
INT
Intel or VLIO Bus
RESET Motorola RX RX
64 Byte RX FIFO RESET# Interface 64 Byte RX FIFO
(RESET#) BRG BRG
Bus
Interface
16/68#
XTAL 1 XTAL1
Crystal Osc / Buffer Crystal Osc/Buffer
XTAL 2 XTAL2
This device is ruggedized for use in harsh operating conditions over the entire common-mode voltage range from -7V to +12V.
Receivers are specially designed to fail-safe to a logic high output state if the inputs are open or shorted. All RS-485 bus-pins are
protected against severe ESD events up to ±15kV (Human Body Model). Drivers are protected from excess current flow caused by
bus contention or output short-circuits by both an internal current limit and a thermal-overload shutdown. Up to 256 transceivers
may coexist while preserving full signal margin.
The device operates from a single 5.0V power supply and draws negligible quiescent power. The device has an independent
enable and disable for the driver and receiver and will enter a low power shutdown mode if both driver and receiver are disabled.
All outputs maintain high impedance during shutdown or when powered-off.
Features Benefits
5.0V single supply operation Low EMI
Controlled driver slew rates 115kbps Higher Density Network
Receiver failsafe on open or shorted lines Vigorous ESD protection
1/8th Unit Load
Robust ESD protection for RS-485 pins ±15kV Applications
Human Body Model
Motor Control
Driver short circuit current limit and thermal shutdown
Building Automation
for overload protection
Security Systems
Industry standard package footprint
Remote Meter Reading
RO 1 8 Vcc
8 PIN NSOIC
RE 2 7 B
SP4082E
DE 3 6 A
Half Duplex
DI 4 5 GND
Single-port 10/100/1000Base-T
Gigabit Transceiver
KSZ9021GQ
Datacom
KSZ9021RL
The KSZ9021GQ and KSZ9021RL are single-port 10/100/1000Base-T Gigabit transceivers,
supporting data transfer over standard CAT-5 unshielded twisted pair cable. This device offers
robust performance and low power consumption. On-chip integration of termination resistors
and LDO controller, along with built-in diagnostic features, significantly reduces the cost and
the complexity of Gigabit Ethernet applications. This device is ideal for enabling Gigabit Ethernet performance in SOHO and SMB
networking applications, such as media converter, GEPON ONU router, wired/wireless Gigabit SOHO/SMB router, and VoIP gateway.
The device is available in two RoHS-compliant package options - 128-pin QFP (KSZ9021GQ, supporting GMII/MII) and 64-pin E-LQFP
(KSZ9021RL, supporting RGMI). Industrial grade is also available.
Features Benefits
Standard compliance ensures to work with other standard
10/100/1000Base-T IEEE 802.3 compliance
compliant, already deployed devices.
Flexible MAC interfaces (GMII/MII for KSZ9021GQ and RGMII
GMII, RGMII, and MII MAC interfaces for KSZ9021RL) support direct connection to MACs in Ethernet
processors and switches at various data rates.
On-chip termination (eliminating 8 external resistors) not only
Integration of termination resistors on the chip simplifies PCB design and reduces system BOM, but also
improves overall signal integrity and EMI emission.
Integration of a LDO controller permits a low cost MOSFET to
Integration of a LDO controller on the chip supply the 1.2V core, which reduces board cost and simplifies
board layout.
Built-in LinkMD® diagnostics helps identification of common
LinkMD TDR-based cable diagnostics
®
cabling problems, including those not addressed by IEEE. It
simplifies network deployment and reduces network downtime.
Automatic MDI/MDIX crossover for IEEE 802.3 and EIA/ Auto-MDI/MDIX eliminates the need for cross-over cable,
TIA 568 standards at all speeds of operation thus reduces installation costs. Easy to use.
PM A
Applications TX10/100/1000
C lo ck
C onfigurations
R eset
Wired/wireless Gigabit SOHO/SMB Router
PM A
SOHO Media Center R X 1000
P C S 1000
Voice-over-Internet Protocol (VoIP) Gateway M E D IA
IN TE R FA C E
Network Attached Storage PM A G M II/RG M II/M II
Laser Printers and Projectors R X 100 P C S 100 Interface
LED Lighting
Available in a full range of white color temperatures (2700K-6500K),
as well as six monochrome colors, OSRAM Opto Semiconductors’
Golden DRAGON Plus is a remarkably bright and very durable LED.
With a silicone dome for improved light output, it’s the ideal choice
for a wide variety of general and specialty lighting applications.
Built using the latest chip technology, the 1-3 W Golden DRAGON Plus is significantly brighter than the standard Golden DRAGON.
Due to its excellent thermal design, Golden DRAGON Plus has an exceptional lifetime of more than 70,000 hours. For the white
devices, OSRAM’s best in class, 3 step MacAdam Ellipse, fine white binning enables ENERGY STAR compliance and unmatched color
homogeneity.
Features Applications
Features
Two Base Platforms Block RAM with a wide range of granularity
Designed for low cost Clock Management Tile (CMT) for enhanced performance
Low static and dynamic power Simplified configuration, supports low-cost standards
Multi-voltage, multi-standard SelectIO banks Enhanced security for design protection
High-speed GTP serial transceivers in the LXT FPGAs Faster embedded processing with enhanced, low cost,
Integrated Endpoint block for PCI Express designs (LXT) MicroBlaze™ soft processor
Efficient DSP48A1 slices Low cost, integrated PCI® technology support compatible
Integrated Memory Controller blocks across 32 bit and 64 bit, 33 MHz and 66 MHz specifications
Abundant logic resources with increased logic capacity Industry-leading IP and reference designs
Logic
The Virtex®-6 family provides the newest, most advanced
Features
Two Base Platforms System Monitor capability on all devices
Cross-platform compatibility Integrated interface blocks for PCI Express designs
Advanced, high-performance, FPGA Logic RocketIO™ GTX transceivers 150 Mb/s to 6.5 Gb/s
Powerful mixed-mode clock managers (MMCM) clocking Integrated 10/100/1000 Mb/s Ethernet MAC block
36-Kb block RAM/FIFOs 40 nm copper CMOS process technology
High-performance parallel SelectIO technology 1.0V core voltage (-1, -2, -3 speed grades only)
Advanced DSP48E1 slices Lower-power 0.9V core voltage (-1L speed grade only)
Flexible configuration options High signal-integrity flip-chip packaging available in standard
or Pb-free package options
The LTC2261-14/LTC2260-14/LTC2259-14 are sampling 14-bit A/D converters designed for digitizing high frequency, wide dynamic
range signals. They are perfect for demanding communications applications with AC performance that includes 73.4dB SNR and
85dB spurious free dynamic range (SFDR). Ultralow jitter of 0.17psRMS allows undersampling of IF frequencies with excellent noise
performance.
DC specs include ±1LSB INL (typical), ±0.3LSB DNL (typical) and no missing codes over temperature. The transition noise is a low
1.2LSBRMS. The digital outputs can be either full rate CMOS, double data rate CMOS, or double data rate LVDS. A separate output
power supply allows the CMOS output swing to range from 1.2V to 1.8V. The ENC+ and ENC– inputs may be driven differentially or
single-ended with a sine wave, PECL, LVDS, TTL or CMOS inputs. An optional clock duty cycle stabilizer allows high performance at full
speed for a wide range of clock duty cycles
Features Applications
Full rate CMOS using 14 data lines Cellular Base Stations
Double data rate (DDR) CMOS, 7 data lines Communications
DDR LVDS, 14 data lines, for reduced digital noise Instrumentation
Straight binary or twos complement data coding Multi-Channel Data Acquisition
Selectable LVDS output current (1.75 to 4.5 mA), to match output Non-Destructive Testing (NDT)
current to the load, while minimizing power dissipation Portable Medical Imaging
Internal 100-ohm resistors which you can switch in, to absorb Software Defined Radio (SDR)
reflections due to impedance mismatch at the receiver
A data randomizer which scrambles the output bits via an exclusive-OR
circuit, to reduce noise coupling from major signal transitions and improve
SFDR (the data receiver, of course, must do a reverse XOR to unscramble
them); LTC claims this can reduce residual tones caused by digital feedback
by 10-15 dB 2-Tone FFT, fIN = 70MHz and 75MHz
0
Typical Application 1.8V 1.2V
–10
–40
–50
+ 14-BIT
D13
CORRECTION • CMOS –60
ANALOG INPUT PIPELINED OUTPUT
LOGIC • OR
INPUT S/H ADC CORE DRIVERS –70
• LVDS
– D0 –80
–90
OGND –100
–110
CLOCK/DUTY
–120
CYCLE 0 10 20 30 40 50 60
CONTROL
FREQUENCY (MHz)
GND
125MHz
CLOCK
Power & Battery Management
LT3682 - 1A Micropower Step-Down
Switching Regulator
36VIN (60V Transient Protection) 1A,
Micropower Step Down Converter
Modern automobile, industrial and telecomm environments continue to include increasingly complex electronic systems. Additionally,
these electrical and physical environments continue to be very harsh for any type of electronics. Wide operating voltage requirements
coupled with large transient voltages and wide temperature variations combine to make life difficult on electronic systems. High efficiency
is of paramount importance as it minimizes thermal design considerations while also maximizing battery run time. Equally important is
very low quiescent current which minimizes the power drawn from a battery when the IC is in a standby mode. Many of these applications
operate from batteries, or utilize back-up batteries, in which a voltage rail must be maintained with no load current for an extended
period of time. Therefore, it is important to keep the quiescent current as low as possible. Common applications are automotive GPS,
security and environmental control systems as well as a myriad of industrial applications. Additionally, as manufacturers increase the
electronic content of their systems, the space
requirements continue to shrink demanding
smaller and more efficient power solutions.
Features Applications
Wide input voltage range of 3.6V to 36V, with transient protection to 60V Automotive Battery Regulation
Up to 1A of continuous output current Automotive Entertainment Systems
Up to 90% efficiency Industrial Supplies
Only 75μA of quiescent current Power for Portable Products
Adjustable, Synchronizable switching frequency: 250kHz to 2.2MHz Distributed Supply Regulation
DA pin to permit the OVLO at any operating frequency
Output is adjustable down to 0.8V
Soft-start capability
Power Good Flag
Tiny 3mm x 3mm DFN-12
New for ZigBee®:
Low cost, high performance
System-on-Chip Transceiver ICs
Wireless
CEL’s new ZIC2410 delivers the industry’s best link budget, plus data rates to 1 Mbps
and an on-board Voice CODEC
CEL’s new ZIC2410 combines a powerful, ZigBee-compliant RF transceiver with an industry-workhorse, 8051-based 8-bit
microprocessor. It’s designed to help simplify your radio designs, shrink their size, lower power consumption, and reduce overall
system cost. Available in QFN48 and VFBGA72 packages, the ZIC2410 is ideal for applications like remote sensing, AMR/AMI,
home and building automation, and security networks. The ZIC2410 joins CEL’s broad line of IEEE 802.15.4 transceiver modules.
Compact and easy to implement, CEL modules are FCC, IC and CE certified, which eliminates the costly, time-consuming
certification of your designs.
Key Features
CEL
CEL ZigBee
ZIGBEERadio
RADIOModules
MODULES
Software / Znet Pro 3.1 Znet Pro 3.1 LSR STAR Protocol LSR STAR Protocol LSR STAR Protocol
ZigBee Stack (ZigBee Pro Certfied) (ZigBee Pro Certfied) BeeStack™ Z-Stack™ Z-Stack™
Key Features:
by Tokyo Electron Device Ltd.
Nu Horizons offers a wide range of development/evaluation boards, tools and kts. For more information, please visit http://ap.nuhorizons.com/development/
Nu Horizons Virtex™-5 LXT Evaluation Platform
Development Tools
The Virtex-5 LXT Platform FPGA is optimized for high-
performance logic with low-power serial connectivity. This
kit includes one of SPF and 8 SMA connectors for easy
evaluation of MGT designs.
Key Features:
10/100/1G Marvell Ethernet Phy
LTC1326 – Linear Technology
micropower precision triple supply monitor
LTC3026 – Linear Technology 1.5A low
input voltage VLDO linear regulator
LTC3412 – Linear Technology 3A, 4MHz,
monolithic synchronous step-down regulator
LTC3418 – Linear Technology 8A, 4MHz,
monolithic synchronous step-down regulator
LTM4601 – Linear Technology 12A DC/DC
µModule power supply
2x16 Tianma display
ISSI DDR2 SDRAM
1 SFP connector
8 SMA connectors 2x16
Character Display 8 LEDs Pushbuttons
$799
Key Features:
XC5VSX95T-1FF136 x4
DDR2 SDRAM x8
GTP x16 ch per FPGA
X4 to each FPGA
X4 SAMTEC connector
Samtec High Speed Interface (120 pin) x1 per FPGA
Optional Expansion capabilities x1 per FPGA
Includes:
Evaluation Board
Documentation
DDR2 DDR2 Power Supply
SDRAM SDRAM
SX95T SX95T
DDR2 DDR2
SDRAM SDRAM Ordering Info:
TB-5V-SX95T4-HSC
DDR2 DDR2
SDRAM SDRAM
SX95T SX95T Price:
DDR2 DDR2 Call Nu Horizons
SDRAM SDRAM
Nu Horizons offers a wide range of development/evaluation boards, tools and kts. For more information, please visit http://ap.nuhorizons.com/development/
Nu Horizons Spartan™-3A DSP Evaluation Kit
Development Tools
Key Features:
XC3SD1800A-4FGG646C Spartan-3A DSP FPGA
16 MB DDR2 SDRAM
16 MB SPI Flash
10/100 Ethernet PHY
14 bit Analog to Digital Converter
Radio Transceiver 2x20 Display 8 LEDs Pushbuttons
Stereo DAC
Video DAC
16 MB DDR2 14 bit ADC
20x2 character LCD Display SDRAM
LTC FastDAAC
Includes: 10/100
Ethernet Phy
Connector
Evaluation Board XC3SD1800A
CS484
Documentation 16 MB SPI Flash RF Radio
Stereo DAC
Ordering Info:
NH-SPAR3ADSP-EVL RS-232 Crystal
Price:
$199.99
Key Features:
5VFX30T FPGA
10/100/1G Marvell Ethernet Phy
LTC1326 – Linear Tech micropower precision triple supply monitor
LTC3026 – Linear Tech 1.5A low input voltage VLDO linear regulator
LTC3412 – Linear Tech 3A, 4MHz, monolithic synchronous step-
down regulator
LTC3418 – Linear Tech 8A, 4MHz, monolithic synchronous step-
2x16
Character Display 8 LEDs Pushbuttons
down regulator
LTM4601 – Linear Tech 12A DC/DC µModule power supply
Linear Tech
2x16 Tianma display
Video DAC Acquisition Header Micron DDR2 SDRAM
Marvell Headers
1 SFP connector
Ethernet Phy Xilinx Virtex
LXT50
8 SMA connectors
64 MB DDR JTAG Header
Nu Horizons offers a wide range of development/evaluation boards, tools and kts. For more information, please visit http://ap.nuhorizons.com/development/