Académique Documents
Professionnel Documents
Culture Documents
Maintenance
tools & equipment
2011
Powertrain
JFP9510 Diagnostic Smoke Machine
Full featured diagnostic capabilities allows the inspection of any pressurized system Compact and simple to use EVAP approved Works with shop air and uses mineral oil
Powertrain
JFP3000 VACUUM FUEL PRESSURE SET
Ideal for testing vacuum lines and components - quickly diagnose internal engine problems such as bad rings, valves, and leaking head gaskets Accurately tests low-pressure fuel systems Helps pinpoint hard-to-find problems such as cracked lines, PCV, fuel pump, fuel filters, and more Professional dual scale gauge reads vacuum and pressure 0-30" Hg vac and 0-70 cm Hg, also reads 0-15 psi and 0-100 KPA and offers zero adjust feature Gauge has a large 3-1/2" face featuring a chrome bezel Gauge is protected with a rugged outer boot Built-in rear hook allows gauge to be hung at eye level Rugged blow-molded case
Powertrain
JFP572 LARGE VALVE SPRING COMPRESSOR
Designed to compress valve springs on overhead valve engines Direct action compressor lever provides high visibility of valve spring retainers located in difficult access areas Includes two valve spring adapters, which fit valve spring retainers up to 1" (25mm) and 1-3/16" (30mm) Jaw opening of 1-3/8" to 5-5/8" (35mm to 142mm) Throat clearance of 5-7/8" (150mm)
Weight lbs.
0.34
3-19/64" 0.26
1-1/16" 23/32"
JFP9SET 9 PieCe SPARK PLUG SET JFP501 FLARING TOOL COMBINATION KIT
Includes all adapters and tools necessary for single and double flaring (standard and metric) as well as the ISO (bubble) flare Works on aluminum, copper, and soft steel Not recommended for use on stainless steel Includes three different sizes and three different configurations most commonly used when working with spark plugs 9/16", 5/8", and 13/16" spark plug sockets in standard, universal, and extra deep lengths Chromed finish for easy clean-up and long-lasting corrosion protection 3/8" square drive sockets feature a rubber insert to securely grab the spark plug Each socket is knurled for easy hand turning Rugged blow-molded case
in.
3/4"
in. B
2-1/4" 2-3/8" 2-3/8" No. 5 Spline 1"
C
1-5/8" 2-3/8" 2-3/8"
Includes three different sizes and three different configurations most commonly used when working with spark plugs 9/16", 5/8", and 13/16" spark plug sockets in standard, universal, and extra deep lengths Universal styles for most applications 3/8" square drive sockets feature a rubber insert to securely grab the spark plug Each socket features a knurl for easy hand turning Black-oxide finish Rugged blow-molded case
in.
L
2-1/2" 2-1/2"
Width
0.19 0.30
Weight lbs.
0.21 0.35
Powertrain
PULLeR SPARK PLUG WIRE BeNT NOSE
Allows for easy access to the spark plug boot
Product ID No.
JFE700A JFE600A
Bend
40 30
Contents
J3210 J3215 J3220 J3225 J235 7/32" 9/32"
15
13/64" 1/4" 5/16" 3/8"
60
15/64"
Length
3" 3" 3-1/2" 3-3/4"
JFP500A STETHOSCOPE
Fast, accurate method for locating trouble in engines Determines if moving parts are worn, such as pistons, gears, valves, water pumps, gaskets, bearings, etc. Plastic ear protectors help reduce shop noise Spring steel diaphragm for long use Shock resistant handle
15
13/64" 15/64" 7/32" 1/4" 9/32" 5/16 11/32" 3/8" Midget Angle Nose Pliers Tool Roll
60
15/64" 13/64" 1/4" 7/32" 5/16" 9/32 3/8" 11/32"
Length
3" 3" 3" 3" 3-1/2" 3-1/2 3-3/4" 3-3/4"
Powertrain
MIDGET ANGLE NOSE PLIERS
Nose angled for easy access Angled teeth provide superior gripping power over standard right angled teeth Plastisol grips for added comfort
Product ID No.
J235
Fluid systems
PISTON RING COMPRESSOR
Wide band has ratchet mechanism to prevent breakage and slippage Includes ell handle
Product ID No.
J2316
Bland Width
3-1/2"
Diameter Range
2-1/8" to 5"
Weight lbs.
0.70
L
4-1/16
A
3/4
B
5/8
C
11/64
Weight lbs.
0.10
Blade Width
1-1/2" 1-1/16"
Blade Length
12" 11"
Weight lbs.
0.30 0.38
Blade Width
7/8"
Blade Length
9"
Weight lbs.
0.30
Length
8-1/2" 8" 9-1/2"
Weight lbs.
0.81 0.81 0.88
Blade Length
7-3/4"
Weight lbs.
0.25
Fluid systems
JFF5325A SWIVEL OIL FILTER WRENCH
Stainless steel band with projection welds for strength and anti-corrosion Heat-treated swivel handle adjusts to a wide arc of positions Minimum grip: 4-1/8" (104.7mm) Maximum grip: 4-7/16" (112.7mm) Over 150 foot pounds of lift
Range
2" to 4-1/4" 2-1/4" to 5" 3-3/4" to 7"
Length
7-3/4"
Weight lbs.
0.56
Fluid systems
PINCH-OFF PLIERS
Patented clamping mechanism provides positive clamping without springs or adjustments Tested to 50,000 cycles without failure Heat-treated steel construction Swivel mounted clamps adjust to provideparallel clamping operation Cushioned hand grips For pinching-off Product flexible fuel lines, ID No. Length brake lines, and 5-1/2" JFF554 vacuum hoses in cars, 9-1/4" Jff555 motorcycles, and 13-3/4 Jff556 engines of all kinds
Capacity
3/4" 1-1/4" 2-1/2"
Adapter Sizes
48mm x 3mm 45mm x 3mm 56.6mm x 3mm 52mm x 3mm 52mm x 2.5mm 63mm x 3mm 62mm x 4mm 52mm x 3mm 34mm x 3mm
Fluid systems
JFF4000 MASTER DISCONNECT SET
Low profile 3/8" Flex Fuel Disconnect tool for disconnecting hard to reach and difficult fuel filters Stepped disconnect tools fit transmission oil cooler lines on many Fords and other vehicles Low-profile fuel module disconnect for GM works great on Suburban, Tahoe, and full-sized truck module applications Coupler disconnect fits applications on transmissions, power steering, and radiators Includes: -- 6 Piece Angled Disconnect Set -- 6 Piece Angled AC/Fuel Line Disconnect Set -- Fuel Filter Disconnect for GM -- Hairpin Disconnect -- Fuel Line Quick Disconnect for GM -- 5/16" & 3/8" Scissor Disconnect -- Coupler Disconnect -- Ford Transmission Line Disconnect Set
COMPRESSION TESTER
Hold in type for quick accurate compression readings Dual scale indicates both psi and metric values (0 - 300 psi, 0 to 20 kg/cm2)
Product ID No.
JCT21
Length
6-1/2"
Weight lbs.
1.2
Description
Gauge Compression 2-1/2" Rubber Compression Cone Compression Tester Repair Kit
Length
3-1.2" 1-1/2" 7-3/16"
Weight lbs.
0.39 0.03 0.29
Fluid systems
electrical systems
COMPRESSION TESTER
Includes compression gauge, O-ring, compression gauge, and instructional pamphlet Flexible hose and quick-disconnect coupler permit fast, easy engagement of threaded fitting into spark plug hole Gauge has convenient side release valve and dual reading scale for both psi and metric values (0 to 300 psi, 0 to 20 kg/cm2) Equipped with neoprene "O" rings for positive finger-tight seal Includes adapters for regular 18mm spark plugs and for regular and long 14mm spark plugs
Product ID No.
JCTR10
Length
10-29/32"
Weight lbs.
1.08
Description
O Ring Gauge Compression 2-1/2" Compression Tester Repair Kit
Length
7/16" 3-1/2" 22-5/16"
Weight lbs.
0.01 0.39 0.8
Length
11-29/32"
Weight lbs.
1.06
Built-in battery charger (accepts standard 110v extension cords) with automatic overcharge protection Built-in removable flashlight 27" #4 AWG cables with full-size clamps 9 amp-hour battery Lightweight 12v DC power socket to power accessories
Description
Gauge Compression 2/Side Compression Tester Repair Kit
Length
2-5/16" 9-1/2"
Weight lbs.
0.35 0.48
10
electrical systems
JFE96030 12 PieCe TERMINAL TOOL KIT
Fits most GM and American Motors computer connectors and terminals Individually handled for easyaccess into tight places Color coded for easy identification
Red Anodized Handle
Tube, Spring-Loaded, 3.3mm x 28.0mm Square Blade, 1.4mm x 19.0mm Flat Blade, 1.5mm x 24.75mm Flat Blade, 2.0mm x 23.0mm Fork Blade, 8.0mm x 24.0mm Flat Blade Screwdriver, 3/16" x 1"
Description
for O2 and oil pressure sending units on late 1980s to mid 1990 vehicles for vacuum switches with a 7/8" hex and some O2 sensors for thermal switches on 19731977 GM vehicles for O2 sensors and vacuum switches on many domestic and imported vehicles requiring wire clearance deep design fits oil pressure sending switches up to 2-5/8" designed with a slot to accommodate the connectors on the heated O2 sensors low profile for use in tight places to remove O2 sensors on many European vehicles; also for Mercedes diesel injectors allows maximum accessibility when removing O2 sensor sockets, also for super-duty 12 and 6 point applications 3-78" long with side slot allows wire clearance can be used to clean and repair threads on exhaust O2 sensor parts, also to clean threads on M18 x 1.5 spark plug socket
3/8" x 7/8" x 90mm oxygen sensor socket 1/2" x 27mm x 85mm fuel injector socket 3/8" x 7/8" x 80mm vacuum switch socket 3/8" x 1-1/16" x 74mm oil sending unit socket 3/8" x 7/8" x 50mm oxygen sensor socket
3/8" x 7/8" x 30mm offset oxygen sensor wrench 3/8" x 22mm special tube socket 2-1/8" offset oxygen sensor wrench 3/8" deep oxygen sensor socket Oxygen sensor thread chaser
Length
3-15/16"
Weight lbs.
0.14
Length
7-1/2"
Weight lbs.
0.55
11
12
13
FLEXIBLE RETRIEVING AND HOLDING TOOLS JFC1463 5 PieCe WHEEL TORQUE EXTENSION kit
Designed to torque wheel nuts on foreign and domestic cars and light trucks For use with thin wall or impact lug nut sockets Includes wall chart and extensions C, E, F, I, and Q Designed to position or retrieve small objects Spring loaded plunger actuates jaws at end of flexible casing
Product ID No.
j2344 J2345
Length
13-1/2" 23-1/2"
Weight lbs.
0.19 0.26
Length
16-3/4" to 26-3/4"
Weight lbs.
0.40
Length
8"
Weight lbs.
0.08
14
Blade Thickness
0.0015" 0.002" 0.003" 0.004" 0.005" 0.006" 0.007" 0.008" 0.009" 0.010"
Weight lbs.
0.01 0.01 0.01 0.04 0.01 0.01 0.01 0.02 0.01 0.02
Strength
1.5 lbs. 3.0 lbs.
Length
19-1/2" 24-1/2"
Weight lbs.
0.27 0.37
INSPECTION MIRROR
Versatile all-angle ball joint Features telescoping handle (J2372 and J2373) With pocket clip (J2373)
Product ID No. Shape
j2370 J2374 J2371 J2372 J2373 Circular Circular Oval Circular Rectangular
Mirror Size
7/8" Dia. 1-1/4" Dia. 1"x 2" 2-1/4"
Length
7-1/2" 8" 8-3/4" 10" to 14"
Weight lbs.
0.08 0.09 0.25 0.25
Blade Thickness
0.0015" 0.002" 0.003" 0.004" 0.005" 0.006" 0.008" 0.010" 0.015"
Weight lbs.
0.01 0.01 0.03 0.01 0.01 0.02 0.02 0.02 0.03
15
J000SL
Includes sizes: .0015", .002" through .006", .008", .010", .012", .014", .015", .020" Sizes: 0.04mm, through 0.10mm, 0.15mm, 0.20mm, 0.25mm, 0.30mm, 0.35mm, 0.40mm, 0.45mm, 0.50mm, 0.55mm, 0.60mm, 0.65mm, 0.70mm, 0.75mm, 0.80mm, 0.85mm, 0.90mm, 0.95mm, 1.00mm
J000R
Includes sizes .009" through .011", .014" through .021", .023" thru .027"
J000M
11 BLADE BENT FEELER GAUGE SET 15 BLADE METRIC FEELER GAUGE SET 9 BLADE METRIC FEELER GAUGE SET 6 BLADE NON-MAGNETIC FEELER GAUGE SET 22 BLADE STEP CUT FEELER GAUGE SET 25 BLADE MASTER FEELER GAUGE SET 9 BLADE STANDARD FEELER GAUGE SET 25 BLADE LONG FEELER GAUGE SET 10 BLADE IGNITION FEELER GAUGE SET
Blades 1/2" wide by 4" overall with a 1 bend in sizes .006", .008", .010" through .015", .018" through .020" Sizes 0.06mm through 0.08mm, 0.10mm, 0.15mm, 0.20mm, 0.25mm, 0.30mm, 0.35mm, 0.40mm, 0.45mm, 0.50mm, 0.55mm, 0.60mm, 0.70mm Includes sizes: 0.06mm, 0.10mm, 0.15mm, 0.20mm, 0.30mm, 0.35mm, 0.40mm, 0.50mm, 0.60mm Sizes .006", .008", .010", .012", .014", .016"
J00MM15
J00MM9 J000BR
J000N
Sizes include: .004/.006" through .025/.027" Includes all short blade sizes .0015" through .040" except .019", 0.021, 0.023, 0.024, 0.026, 0.027, 0.028, 0.029, 0.031, 0.033, 0.034, 0.036, 0.037, 0.038, 0.039 Blade size 1/2 by 3 Short blades in sizes .003" through .005", .006", .008", .010", .012", .015", .018", in No. 000C holder Sizes: .0015", .002" through .021", .025", .027", .030", .040" Includes sizes .013", .015", .017", .018", .020", .025", .030", .032", .035" .040"
J000AA
J000A
J000TL J000D
16
Overall Length
1-1/2"
Weight lbs.
0.17
Size Range
J74206
25 Piece Metric 8mm to 36mm Socket Set 19 Piece Socket Set 11 Piece Socket Set 3/8" to 1-1/2"
J74106
Product ID No.
j5260W J5260-06W J5262W
Overall Length
3" 6" 12"
Weight lbs.
0.17 0.29 0.65 J74102 J74202
1/2" to 1-1/8"
Overall Length
9"
Weight lbs.
0.35
Range Max.
250 ft. lbs. 1 ft. lbs. 100 ft. lbs. 0.5 ft. lbs.
17
Max. Opening
1-1/8" 1-5/16" 1-1/2" Tool Roll
Length
8" 10" 12"
Weight lbs.
0.57 0.95 1.54
Product ID No.
J1200F-T500
J1200H-T500
3/8" to 3/4"
Contents
J3764 J3768 J3772
in.
3/8"x7/16" 1/2"x9/16" 5/8"x11/16" 3/8"x7/16" 1/2"x9/16" 5/8"x11/16"
Length
6-1/4" 7-1/2" 8-3/4" 6-1/4" 7-1/2" 8-3/4"
Weight lbs.
0.18 0.27 0.38 0.18 0.27 0.38
J1200RM-T500 17 Piece Metric Wrench Set J1200HM-T500 9 Piece Metric Wrench Set
18
mm.
Length
6-3/4 6-3/4 6-3/4 6-3/4 6-3/4 6-3/4 6-3/4 6-3/4 6-3/4 7 7
J9201MB J9204M J92055M J9206M J9207M J9208M J9209M J92010M J92011M J92013M J92014M
in.
Length
6-11/16 6-11/16 6-11/16 6-11/16 6-11/16 7 7
Contents
3/16 7/32 1/4 9/32 5/16 J9207 J9208 J9209 J9210 J9211 J9212 J9214 J9216 J9218 J9220
in.
Product ID No.
J4979TXCG T9-T40
Length
76
J9200DB J9206
MAX.
1-1/8 1-1/2 2-5/8
Jaw Length
1-3/8 1-5/8 2-1/4
Head Width
1-3/4
1-15/16 2-3/4
4-1/16 3-3/8
19
Jaw Length
1-11/16 2-5/8
Jaw Length
Head Width
17/32
7-25/32 1-9/16
Jaw Length
1-5/8
Head Width
3/4
Size
4 oz. 8 oz. 12 oz. 16 oz. 24 oz. 32 oz. 40 oz.
Overall Length
11 12 13 14-1/2 15 15-7/8 16-3/8
Weight lbs.
0.45 0.83 1.14 1.45 2.00 2.42 2.84
Length
4-5/8 4-7/16 5-1/16 6-1/16 7-5/16
19/32 3/8
20
Contents
J4739-10W J4739-15W J4739-20W J4739-25W J4739-27W J4739-30W J2584 J2590 T10 T15 T20 T25 T27 T30 Socket Bar 6-1/4 Socket Clips
Drive Size
1/4 3/8 3/8
Overall Length
5.7 8.5 11
J47102
Drive Size
1/4 3/8
Overall Length
5 7
J47202
12 Piece 4mm to 14mm Metric Deep Socket Set 29 Piece Metric Socket Set 12 Piece Metric Universal Socket Set 4mm to 14mm; 4mm to 14mm Deep 5mm to 15mm
j47206
J47205
21
Overall Length
2 3 6 10 14-1/8
Weight lbs.
0.05 0.08 0.15 0.24 0.30
Overall Length
2-1/10 6
Weight lbs.
0.06 0.14 J52128 12 Piece Socket Set 16 Piece Metric Socket Set 13 Piece Socket Set 21 Piece Metric Socket Set 13 Piece Deep Socket Set 6
J52218
12
6mm to 19mm
6 6
Overall Length
6
Weight lbs.
0.22
J52114
1/4 to 1 Deep
18 Piece 6 Metric Deep Socket Set 7 Piece Universal Socket Set 10 Piece Metric Universal Socket Set 6
Overall Length
6-1/4
Weight lbs.
0.11
J52100
j52201
J4900BD 7 Piece 3/8" DRIVE BALL STYLE EXTRA LONG HEX BIT SET
Set includes socket bar and socket clips Extra long bits for additional reach Weight: 1.46 lbs.
22
Product ID No.
J5238C J5239C
Description
6 Piece 8 Piece T15-T40 T15-T50
Contents
J7099 J60002 J60008 J60020 J60202 J60208 J60050 J60052 J60054 J60256 J60262 J6930 J6931
Description
Driver Hand Impact 3/8 Drive Bit Insert 1 Phillips 1/4 Hex Bit Insert 2 Phillips 1/4 Hex Bit Insert 3 Phillips 1/4 Hex
Length
5-1/2 1 1 1 1 1 1-1/4 1-1/4 1-1/4 1-1/2 1-1/2 1-5/16 1-1/4
Bit Insert 4F-5R Slot 1/4 Hex Bit Insert 10F-12R Slot 1/4 Hex Bit Insert 1 Phillips 5/16 Hex Bit Insert 2 Phillips 5/16 Hex
Bit Insert 3 Phillips 5/16 Hex Bit Insert 10F-12R Slot 5/16 Hex Bit Insert 14F-16R Slot 5/16 Hex Bit Holder Power 3/8 Dr. 5/16 Bit Holder
23
2195 East View Parkway Suite 103 Conyers, GA 30013 1-800-800-TOOL | 770-648-9100 | www.stanleyproto.com
P21114