Académique Documents
Professionnel Documents
Culture Documents
DIM SA
Connections
The signal amplifier has the following connections: Power supply (A) 110V input (B) 110V output (C)
Installation
Safety instructions
The signal amplifier must only be installed and put into operation by a qualified electrician. The applicable safety regulations and accident prevention regulations must be observed. WARNING! Exposed, live cables. Danger of electric shock! Only work on the signal amplifier when it is de-energised. CAUTION! Destruction of the signal amplifier and other devices through incorrect mounting! Do not connect the control outputs of multiple signal amplifiers in parallel. Only use ballasts with a 1...10V interface. Do not exceed the maximum number of connectable components. Only supply signal amplifiers with an AC operating voltage, especially in networks with UPS systems.
L N PE
1...10V
DIM SA
1...10V
~ 230V ~ 50-60Hz
in +
1...10V out
~ 230V / ~ 50Hz +
- 1...10V
. . .
1...10V EVG
DIM SA
1...10V
~ 230V ~ 50-60Hz
. . .
1...10V out
in +
~ 230V / ~ 50Hz +
D Increase in the number of electronic ballasts and luminaires that can be connected to the control unit(H) Connect the control output of the control unit with the 1...10V inputs of the signal amplifier. Connect the 1...10V outputs of the signal amplifier with the 1...10V control inputs of the electronic ballast. Note: Ensure that the configuration is symmetric: As far as possible, distribute the number of electronic ballasts evenly among the signal amplifiers. Connect all electronic ballasts to the signal amplifiers if possible. If some of the electronic ballasts are connected directly to the control unit, dim settings and dim speeds may vary within the system.
- 1...10V
. . .
1...10V EVG
Page 1 of 2
Installation (cont.)
E
L N PE
1...10V
E Increase in the permissible control line length of the control unit(H) Maximum line length between the distributors of the signal amplifiers: 300m.
DIM SA
max. 300 m
1...10V
~ 230V ~ 50-60Hz
in +
1...10V out
~ 230V / ~ 50Hz +
- 1...10V
. . .
1...10V EVG
DIM SA
max. 300 m
1...10V
~ 230V ~ 50-60Hz
. . .
in -
+ +
1...10V out
~ 230V / ~ 50Hz +
- 1...10V
. . .
1...10V EVG
L N PE
DIM MICO
F Configuration of lighting with daylight-dependent control Suitable light sensor: DIM MICO
~ 230V / ~ 50Hz +
DIM SA
1...10V
~ 230V ~ 50-60Hz
1...10V out
in +
- 1...10V
1...10V EVG
~ 230V / ~ 50Hz +
- 1...10V
. . .
1...10V EVG
L N PE
N L
DIM MULTI
G Configuration of lighting with daylight- and motiondependent control Suitable light and motion combination sensor: DIM MULTI
DIM SA
1...10V
~ 230V ~ 50-60Hz
in -
+ +
~ 230V / ~ 50Hz +
- 1...10V
1...10V EVG
~ 230V / ~ 50Hz +
- 1...10V
. . .
1...10V EVG
Appendix
Technical data
Operating voltage Supply connection Power consumption Load capacity 230V; 50-60Hz (no DC operation) L, N, PE Approx. 2W 110V input: max. 1.5mA 110V output: max. 100mA or 100 OSRAM 110V ECG Protection class Protection type Operating temperature Dimensions (L x W x H) I IP 20 0C +50C 189 x 30 x 28mm 180mm
IV 2009 DIM_SA_ma0904en_we1.01.indd OSRAM GmbH Kunden Service Center Customer-Service-Center (CSC) Steinerne Furt 62 86167 Augsburg Germany Tel : +49 (0) 1803 677 - 200 (kostenpflichtig / charges apply) Fax.: +49 (0) 1803 677 - 202 www.osram.com www.osram.de
The EMC requirements to EN 61547, EN 61347-11 and EN 55015 are fulfilled. Conformity with the relevant EU directives is confirmed by the CE symbol.
40083210970958
4008321097095
Page 2 of 2