Académique Documents
Professionnel Documents
Culture Documents
Francheska P. Gamo, Anatoly M. Pablo, Paul Ian N. Olalo, Leonardo T. 3/1/2013 Wong, Otto Hongsan T.
DATE:
TWO WAY SLAB Inputs: f'c = S, Shoter side length = L, Longer side Length = Depth of Beam = Width of Beam = Total Dead Load = Total Live Load = 21.000 Mpa 5.000 6.000 0.4000 0.2000 2.000 2.000 m m m m KPa KPa fy = Wc = cover = = Main bar = Temp bar = = 275.000 23.600 25.000 0.900 12 10 0.850 Mpa Kpa mm mm mm
: assume 1ft width of support S/L = Thickness Slab Thickness = 0.828 : TWO WAY SLAB
or 125.000
mm
100.000 mm
= =
all sides (discontinuous) all sides (continuous) left and right sides (continuous), top and bottom sides (discontinuous) left and bottom sides (continuous), right and top sides (discontinuous) top and bottom sides (continuous), left and right sides (discontinuous) only top (continuous) only right (continuous) only top (discontinuous) only right (discontinuous)
University of Santo Tomas Faculty of Engineering - Civil Engineering Department ETABS DESIGN Title: SLAB DESIGN DESIGNERS: Beltran, Francheska P. Gamo, Anatoly M. Pablo, Paul Ian N. Olalo, Leonardo T. 3/1/2013 Wong, Otto Hongsan T. CASE 4 0.828
DATE:
Moment Coefficient *Short Direction Negative Moment Continuos Dead Load Positive Moment Live Load Positive Moment *Long Direction Negative Moment Continuos Dead Load Positive Moment Live Load Positive Moment Moments *Short Direction Negative Moment Continuos Dead Load Positive Moment Live Load Positive Moment MDL+LL = Negative Moment Discontinuos *Long Direction Negative Moment Continuos Dead Load Positive Moment Live Load Positive Moment MDL+LL = Negative Moment Discontinuos Use largest moment : 6.624 KN-m 1.663 2.477 4.140 KN-m 1.380 KN-m 9.748 KN-m 9.748 KN-m 2.409 3.544 5.953 KN-m 1.984 KN-m 0.032 0.018 0.022 0.068 0.037 0.045
5.953
KN-m
4.140
KN-m
University of Santo Tomas Faculty of Engineering - Civil Engineering Department ETABS DESIGN Title: SLAB DESIGN DESIGNERS: Beltran, Francheska P. Gamo, Anatoly M. Pablo, Paul Ian N. Olalo, Leonardo T. 3/1/2012 Wong, Otto Hongsan T.
DATE:
19065126050.420
p^2 +
-2475000000.000
p +
9748144.552
=0
p=
0.126
&
P max = P min =
if min< < max, adequate Reinforcements *Short Direction M 9.748 5.953 1.984 S 278.155 461.314 502.656 P
no. of bars 3.595 2.168 1.989 Use Spacing 250.000 250.000 250.000
no. of bars 2.417 1.989 1.989 Use Spacing 250.000 250.000 250.000
University of Santo Tomas Faculty of Engineering - Civil Engineering Department ETABS DESIGN Title: SLAB DESIGN DESIGNERS: Beltran, Francheska P. Gamo, Anatoly M. Pablo, Paul Ian N. Olalo, Leonardo T. 3/1/2013 Wong, Otto Hongsan T.
DATE:
Shear WA = WB = VA = (WA * S) /2 = VB = (WB * L) /2 = Details For Short Direction -Mcon : Therefore use MDL+LL : Therefore use -Mdis : Therefore use 4.231 1.969 10.154 5.710
12
mm main bars @
250.000 mm O.C.
12
mm main bars @
250.000 mm O.C.
12
mm main bars @
250.000 mm O.C.
For Longer Direction -Mcon : Therefore use MDL+LL : Therefore use -Mdis : Therefore use
12
mm main bars @
250.000 mm O.C.
12
mm main bars @
250.000 mm O.C.
12
mm main bars @
250.000 mm O.C.