Académique Documents
Professionnel Documents
Culture Documents
DKI-50185- A
bATEX
ATEX directive
II 1 G D G 2 D G 3 D
II 3 G / D EEx nA II T6 X
VQCxxx HO Tamb =-10C to +50C IP65 T 80C
Category
Directive 94/9/EC, known as ATEX directive, is one of the directives based on the New Approach towards technical harmonization and standardisation. The New Approach is a new regulatory technique and strategy laid down by the European Council Resolution of 1985, in order to allow free movement of goods within the EU market and to prevent barriers to trade. Products in compliance with all provisions of applicable directives (such as Directive 94/9/EC for ATEX) must bear the CE marking. This is an indication that the products comply with the requirements of applicable directives and have been subjected to the conformity assessment procedure provided for in these directives.
ATEX compliance
Category
Standards Standards for for Electrical Non-electrical product product EN 50014 EN13463-1
bATEX
definitions
General requlrements Part-number Year Operating temperature IP (only for Dust) T temperature(only for Dust) Dust protection Types of Protection Constructional safety "c" Max. Surface temperature Types of Protection "n" Increased Safety "e" Encapsulation "m" Flameproof Enclosure "d" Oil lmmersion "o" Pressurized "p" Powder Filling "q" Intrinsically Safety "ia" Intrinsically Safety "ib"
all all
Potentially explosive atmospheres are atmospheres likely to become explosive due to local and operational conditions. The ATEX directive regards explosive atmospheres which are defined as mixtures with air, under atmospheric conditions, of flammable substances in the form of gases, vapours, mists or dusts in which, after ignition has occurred, combustion spreads to the entire unburned mixture. (Quotation from Directive 94/9/EC) The following applications are explicitly excluded by the ATEX directive and must comply with other specific standards: medical devices, equipment or safety devices to be used with explosive or chemically unstable substances, equipment for domestic and non-commercial environments with explosive atmosphere generated by leakage of fuel gas, personal protective equipment, offshore vessels, mobile units and means of transport. Certified equipment is designed to prevent the generation of ignition sources as defined by the standard EN1127-1: hot surfaces flames and hot gases Zone 2 Zone 1 mechanically generated sparks Category Category 3 2 electrical sparks stray electric currents, cathodic corrosion protection static electricity Zone 0 lightning electromagnetic fields Category 1 electromagnetic radiations ionising radiations ultrasonics adiabatic compression shock waves, gas flows chemical reactions
EN 50281-1-1 EN13463-1
EN13463-5
T1 T2 T3 T4 T5 T6
EN13463-3 EN13463-7
X = means that special conditions for use are in the operating manual. E.g. ; Not impact proof.
INDEX
Actuator 55-C76 Air Cylinder 55-C85 Air Cylinder 55-C95 Air Cylinder P. 04 P. 06 P. 08 P. 10 P. 12 P. 14 P. 16 P. 18 Rotary Actuator 55-CRB1 Rotary Actuator 55-CRB2 Rotary Actuator 55-CRBU2 Rotary Actuator 55-C(D)RQ2 Rotary Actuator 56-C(D)RB1 Rotary Actuator 56-C(D)RB2 Rotary Actuator 56-C(D)RBU2 Rotary Actuator Auto Switches Instruments IP5000 Pneumatic Positioner IP6000-X14 Electro Pneumatic Positiner IP8000-X14 Electro Pneumatic Positiner P. 48 P. 49 P. 52 P. 22 P. 24 P. 26 P. 28 P. 30 P. 32 P. 34 P. 36 Others 56-PA3000/5000 Process Pump 56-VBA Booster Regulator Directional Valves 52-SY 5 Port Solenoid Valves 56-SV 5 Port Solenoid Valves 56-VQC 5 Port Solenoid Valves 56-EX500 Serial Transmission Safety Precautions Safety Instruictions P.113 P. 60 P. 80 P. 92 P.108 P. 58 P. 59
bClassification
Potentially explosive environments are classified into zones in accordance with Directive 1999/92/EC. These are: 0, 1, 2 for gas explosive atmospheres 20, 21, 22 for dust explosive atmospheres
The ATEX directive defines categories of equipment and protective systems, which can be used in the corresponding zones as per the following table. Zone Presence of the explosive Equipment atmosphere category Gas Dust Continuously or for long periods 1 0 20 >1000 hours/year Occasionally 2 1 21 10~1000 hours/year Rarely or for short periods 3 2 22 <10 hours/year
55-CP95 Air Cylinder 55-CS1 Air Cylinder 55-(E)CQ2 Compact Cylinder 55-CXS Dual Rod Cylinder 55-MY1B Mechanically Rodless Cylinder
Series
32, 40
55-C76
How to order
55 - CD76 E 32
ATEX category 2 Built-in magnet
D None Built-in magnet
50 C
Cushion
C Rubber cushion Air cushion (only "E" execution)
Mounting
E Double end type F Front nose type Y Front nose in line type
Except for air cushion type.
Accessories
Trunnion Clevis Single knuckle joint Double knuckle joint Floating joint
For 55-CD76 When using an Auto switch, select the appropriate switch from the following table and order it separately. Applicable auto switch specifications Auto switch only conforms to Category 3. (II 3GD EEx nA II T5x -10C Ta +60C IP67) For detailed specifications on the D-A73(H), A80(H), F7P(V), C73, C80, and H7A2, please refer to the relevant pages in Best Pneumatics. (Note: Reed auto switches for AC 100V and DC 100V are not within the specification.) Type Model No. Rail mounting D-A73-588 D-A80-588 Reed auto switch D-A73H-588 D-A80H-588 Solid state auto switch D-F7PV-588 D-F7P-588 D-C73-588 D-C80-588 Band mounting Indicator Electrical entry Wiring (Output) 24V 2-wiring 24V Load voltage DC 12V 48V or less 48V or less IC circuit IC circuit IC circuit Relay PLC 12V AC 0.5 () Lead wire (m) 3 (L) 5 (Z) Applicable load
Grommet (Perpendicular entry) Yes 3-wiring Grommet (PNP) D-H7A2-588 (In-line entry)
0.5m --- Nil (e.g.) D-A73-588 3 m --- L (e.g.) D-A73L-588 5 m --- Z (e.g.) D-A73Z-588
Note 1)
Note 2) When mounting an auto switch on a 55- series (Category 2) Model, the ATEX category of the auto switch cylinder changes to Category 3, which is the same category as the auto switch.
When ordering a band mounting type auto switch, also order a mounting bracket from the following list at the same time. Auto switch mounting bracket/ Part no. (Band mounting type)
Series
55-C76
Specifications
Bore size ATEX category Action Fluid Proof pressure Max. operating pressure Min. operating pressure Ambient and fluid temperature Lubrication Operating piston speed Allowable stroke tolerance Cushion Thread tolerance Port size G1/8
1)
32
40
II 2GDc
Double acting 1.5MPa 1.0MPa 0.05MPa 10 to 60C (No freezing) Not required (Non-lube) 50 to 1000 mm/s to 250: +1.0 , 251 to 1000: +1.4 0 0 Rubber cushion, Air cushion JIS class 2 G1/4
Symbol
Standard: double action Rubber Cushion Single rod
Mounting
Note 1) This cylinder can be used in zones 1 and 21 and in zones 2 and 22. If the cylinder is used with SMC category 3 type auto switch, then the cylinder can only be used in zones 2 and 22 and not in zones 1 and 21.
Note) All other specifications (dimensions, drawings, etc.) are the same as the non ATEX type.
Series
Double acting Single rod
ATEX category 2 Magnet
None D Built-in magnet
55-C85
How to Order
100 C
Cushion
C Rubber bumper (Standard) Air cushion (only "N" execution, bores 10 to 25mm)
55-C D 85 N 16
Bore size-Stroke
Bore size (mm) 8 10 12 16 20 25
10, 25, 40, 50, 80, 100, 125, 160, 200 10, 25, 40, 50, 80, 100, 125, 160, 200, 250, 300
1000
10
12
16
20
25
Foot (1 pc.) Foot (2 pcs. with mounting nut 1 pc.) Flange Trunnion Clevis Single knuckle joint Double knuckle joint Floating joint
C85L25A C85L25B C85F25 C85T25 C85C25 KJ8D KJ10D GKM8-16 GKM10-20 JA20 JA30 -8-125 -10-125
Note) Please order mounting brackets separately. For 55-CD85 When using an Auto switch, select the appropriate switch from the following table and order it separately. Applicable auto switch specifications Auto switch only conforms to Category 3. (II 3GD EEx nA II T5x -10C Ta +60C IP67) For detailed specifications on the D-A73(H), A80(H), F7P(V), C73, C80, and H7A2, please refer to the relevant pages in Best Pneumatics. (Note: Reed auto switches for AC 100V and DC 100V are not within the specification.) Type Model No. Rail mounting D-A73-588 Reed auto switch D-A73H-588 D-A80H-588 Solid state auto switch D-F7PV-588 D-F7P-588 D-A80-588 D-C73-588 D-C80-588 Band mounting Indicator Electrical entry Wiring (Output) 24V 2-wiring 24V Load voltage DC 12V 48V or less 48V or less IC circuit IC circuit IC circuit Relay PLC 12V AC 0.5 () Lead wire (m) 3 (L) 5 (Z) Applicable load
Grommet (Perpendicular entry) Yes 3-wiring Grommet (PNP) D-H7A2-588 (In-line entry)
0.5m --- Nil (e.g.) D-A73-588 3 m --- L (e.g.) D-A73L-588 5 m --- Z (e.g.) D-A73Z-588
Note 1)
Note 2) When mounting an auto switch on a 55- series (Category 2) Model, the ATEX category of the auto switch cylinder changes to Category 3, which is the same category as the auto switch.
When ordering a band mounting type auto switch, also order a mounting bracket from the following list at the same time. Auto switch mounting bracket/ Part no. (Band mounting type)
10
25
Series
55-C85
Specifications
Bore size (mm) ATEX category 1) Piston rod dia. (mm) Piston rod thread Ports Action Fluid Air Cushion/Single Rod Proof pressure Max operating pressure Min operating pressure Ambient and fluid temperature Cushion Lubrication Piston speed Allowable kinetic energy Rubber Bumper Air Cushion Rubber bumper Air cushion 0.02J 0.03J 0.17J 0/+1 0.1MPa 0.08MPa 10 to 60C Rubber bumper, Air cushion (Except for 8) Not required. If necessary turbine oil no.1 ISOVG32 is recommended 50 to 1000mm/s 0.04J 0.19J 0.09J 0.4J 0.27J 0.66J 0.4J 0.97J 4 M4 X 0.7 M5 4 M4 X 0.7 M5 8 10 12 16 20 25
II 2GDc
6 M6 X 1 M5
90C (T5) Ta 10 to 40C 110C (T4) Ta 40 to 60C 6 M6 X 1 M5 8 G1/8 10 G1/8 M8 X 1.25 M10 X 1.25
Symbol
Double Acting/Single Rod
Stroke tolerance
0/+1.4
Note) All other specifications (dimensions, drawings, etc.) are the same as the non ATEX type.
Note 1) This cylinder can be used in zones 1 and 21 and in zones 2 and 22. If the cylinder is used with SMC category 3 type auto switch, then the cylinder can only be used in zones 2 and 22 and not in zones 1 and 21.
Series
ATEX category 2 Piston rod type
S K Standard Non-rotating rod (32~100 only)
32, 40, 50, 63, 80, 100, 125, 160, 200, 250 How to Order 55-C95SD B 32 100 W XC6
Special
XC6 Standard Stainless steel rod and nut
55-C95
Built-in magnet
D None Built-in magnet 32 40 50 63 80 100 125 160 200 250
Rod Specifications
Hard chromed rod as standard W Note) Double rod
Note) Double rod is not available for bore size diameter
Stroke (mm)
Refer to standard stroke table
Model Selection
Execution Model Piston Rod Adjustable Options Stroke End Cushioning Standard Hard Chrome W 32 40 50 63 80 100 125 160 200 250
Bore size
55-C95 SB 55-C95 SDB 55-C95 ST With Mounting Centre Trunnion 55-C95 SDT 55-C95 KB Non-rotating 55-C95 KDB piston rod Standard Type
Note1) 55-C95 can be used in zones 1 and 21 and in zones 2 and 22. Note2) If the 55-C95 cylinder is used with SMC category 3 type auto switch, then the 55-C95 cylinder can only be used in zones 2 and 22 and not zones 1 and 21. Note3) Piston rod material is stainless steel.
For 55-C95 When using an Auto switch, select the appropriate switch from the following table and order it separately. Applicable auto switch specifications Auto switch only conforms to Category 3. (II 3GD EEx nA II T5x -10C Ta +60C IP67) For detailed specifications on the D-A54, A67, and F5P, please refer to the relevant pages in Best Pneumatics. (Note: Reed auto switches for AC 100V and DC 100V are not within the specification.) Indicator Type Model No. D-A54-588 D-A67-588 D-F5P-588 Grommet Electrical entry Wiring (Output) Load voltage DC 24V 2-wiring 24V or less 3-wiring (PNP) 24V 5V,12V Note 1) IC circuit IC circuit solid state auto switch is available after receiving an order. Relay PLC 12V AC 0.5 () Lead wire (m) 3 (L) 5 (Z) Applicable load
Yes No
Grommet
Yes
When ordering a tie rod mounting type auto switch, also order a mounting bracket from the following list at the same time. Note 2) When mounting an auto switch on a 55- series (Category 2) Model, the ATEX category of the auto switch cylinder changes to Category 3, Auto switch mounting bracket/ Part no. (Tie rod mounting) which is the same category as the auto switch. Tube I.D. (mm) Auto switch
0.5m --- Nil (e.g.) D-A54-588 3 m --- L (e.g.) D-A54L-588 5 m --- Z (e.g.) D-A54Z-588
32,40 BT-03
50,63 BT-05
80,100 BT-06
125 BT-08
160 BT-16
200 BT-16
250 BT-20
Series
Specifications
Bore size ATEX category Action Fluid Proof pressure Max. operating pressure Min. operating pressure Ambient and fluid temperature Lubrication Operating piston speed 32 40 50 63 80
55-C95
100 125 160 200 250 95C (T5) Ta 10 to 40C 115C (T4) Ta 40 to 60C Air
II 2GDc
Double acting 1.5MPa 1.0MPa 0.05MPa 10 to 60C (No freezing) Not required (Non-lube) 50 to 1000 mm/s to 250:
+1.0, 0
50 to 700 mm/s
+1.4 ,1001 0
50 to 500 mm/s
Allowable stroke tolerance Cushion Thread tolerance Port size Mounting G1/8
251 to 1000:
to 1500: +1.8 0
Both ends (Air cushion) JIS class 2 G1/4 G1/4 G3/8 G3/8 G1/2 G1/2 G3/4 G3/4 Basic, axial foot, front flange, rear flange, G1
Standard Stroke
Note) All other specifications (dimensions, drawings, etc.) are the same as the non ATEX type.
Bore size (mm) 32 40 50 63 80 100 125 160 200 250 Standard stroke (mm) 25, 50, 80, 100, 125, 160, 200, 250, 320, 400, 500 25, 50, 80, 100, 125, 160, 200, 250, 320, 400, 500 25, 50, 80, 100, 125, 160, 200, 250, 320, 400, 500, 600 25, 50, 80, 100, 125, 160, 200, 250, 320, 400, 500, 600 25, 50, 80, 100, 125, 160, 200, 250, 320, 400, 500, 600 25, 50, 80, 100, 125, 160, 200, 250, 320, 400, 500, 600 Each stroke will be made to order Each stroke will be made to order Each stroke will be made to order (*) Max. stroke 700 800 1200 1200 1400 1500 1600 1600 2000 2400
Each stroke will be made to order (*) Please consult SMC for longer stroke.
Bore size
(1)
32
40
50
63
L5040 L5050 Foot L5032 L5063 F5040 F5050 Flange F5032 F5063 C5040 C5050 Single rear clevis C5032 C5063 D5040 D5050 Double rear clevis D5032 D5063 Double rear clevis DS DS5032 DS5040 DS5050 DS5063 (for ES accessory) Angled rear clevis ES ES5032 ES5040 ES5050 ES5063 with ball joint E5040 E5050 Angled rear clevis E E5032 E5063 Trunnion pivot C95-S C95-S03 C95-S04 C95-S04 C95-S06 bracket Rod clevis GKM GKM10-20 GKM12-24 GKM16-32 GKM16-32 Piston rod ball joint KJ10D KJ12D KJ16D KJ KJ16D Floating joint JA JA30-10-125 JA40-12-125 JA50-16-150 JA50-16-150 L F, G C D
Note 1) Two foot brackets required for one cylinder. Note 2) Accessories for each mounting bracket are as follows. Foot, Flange, Single clevis: Mounting bolts Double rear clevis: (D,DS): Clevis pin Note 3) C95-S: Set of 2 pcs. Note 4) GKM according to ISO 8140 Note 5) KJ according to ISO 8139 Note 6) Piston rod nut is standard Note 7) Please consult SMC
Note 7)
Series
ATEX category 2 Built-in magnet
D None Built in magnet
55-CP95
How to Order 100 W
Rod Specifications
W Hard chromed rod as standard Double rod
55-CP95SD B 32
Mounting
B L F G C D Basic/Without bracket Axial foot Front flange Rear flange Single rear clevis Double rear clevis
Model Selection
Execution Model Piston Rod Adjustable Options Stroke End Cushioning Standard Hard Chrome W
For 55-CP95 When using an Auto switch, select the appropriate switch from the following table and order it separately. Applicable auto switch specifications Auto switch only conforms to Category 3. (II 3GD EEx nA II T5x -10C Ta +60C IP67) For detailed specifications on the D-Z73, Z80, Y7P, and Y7PV, please refer to the relevant pages in Best Pneumatics. (Note: Reed auto switches for AC 100V and DC 100V are not within the specification.) Indicator Type Reed auto switch Model No. D-Z73-588 D-Z80-588 D-Y7P-588 D-Y7PV-588 Electrical entry Grommet (in-line) Grommet (in-line) Grommet (Perpendicular) Wiring (Output) 2-wiring Load voltage DC 24V 12V 48V or less IC circuit Relay PLC 24V 5V,12V IC circuit AC 0.5 () Lead wire (m) 3 (L) 5 (Z) Applicable load
Yes No
Yes
3-wiring (PNP)
When ordering a direct mounting type auto switch, also order a mounting bracket from the following list at the same time. Note 2) When mounting an auto switch on a 55- series (Category 2) Model, the ATEX category of the auto switch cylinder changes to Category 3, Auto switch mounting bracket/ Part no. (Direct mounting type) which is the same category as the auto switch. Tube I.D. (mm) Auto switch
0.5m --- Nil (e.g.) D-Z73-588 3 m --- L (e.g.) D-Z73L-588 5 m --- Z (e.g.) D-Z73Z-588
Note 1)
32,40,50,63,80,100 BMP1-032
10
Series
55-CP95
Specifications
Bore size ATEX category 1) Action Fluid Proof pressure Max. operating pressure Min. operating pressure Lubrication Ambient and fluid temperature Operating piston speed Allowable stroke tolerance 32 40 50 63 80 100
II 2GDc
Double acting Air (Non-lube) 1.5MPa 1.0MPa 0.05MPa Not required (Non-lube) 10 to 60C 50 to 1000mm/s
+1.4 to 250:+1.0 0 , 251 to 1000: 0
Both ends (Air cushion) G1/4 G3/8 G3/8 G1/2 Basic, axial foot, front flange, rear flange, single rear clevis, double rear clevis
Note 1) This cylinder can be used in zones 1 and 21 and in zones 2 and 22. If the cylinder is used with SMC category 3 type auto switch, then the cylinder can only be used in zones 2 and 22 and not in zones 1 and 21.
Standard Stroke
Note) All other specifications (dimensions, drawings, etc.) are the same as the non ATEX type.
Bore size (mm) 32 40 50 63 80 100 Standard stroke (mm) 25, 50, 80, 100, 125, 160, 200, 250, 320, 400, 500 25, 50, 80, 100, 125, 160, 200, 250, 320, 400, 500 25, 50, 80, 100, 125, 160, 200, 250, 320, 400, 500, 600 25, 50, 80, 100, 125, 160, 200, 250, 320, 400, 500, 600 25, 50, 80, 100, 125, 160, 200, 250, 320, 400, 500, 600 25, 50, 80, 100, 125, 160, 200, 250, 320, 400, 500, 600 Max. stroke 700 800 1200 1200 1400 1500
L5032 Foot(1) F5032 Flange C5032 Single rear clevis D5032 Double rear clevis Double rear clevis DS5032 (for ES accessory) Angled rear clevis ES5032 with ball joint E5032 Angled rear clevis Rod clevis GKM10-20 Piston rod ball joint KJ10D Floating joint JA30-10-125
E5100 E5080 E5040 E5050 E5063 GKM20-40 GKM20-40 GKM12-24 GKM16-32 GKM16-32 KJ20D KJ20D KJ12D KJ16D KJ16D JA40-12-125 JA50-16-150 JA50-16-150 JAH50-20-150 JAH50-20-150
Note 1) Two foot brackets required for one cylinder. Note 2) Accessories for each mounting bracket are as follows. Foot, Flange, Single clevis: Mounting bolts Double rear clevis: (D,DS): Clevis pin Note 3) GKM according to ISO 8140 Note 4) KJ according to ISO 8139 Note 5) Piston rod nut is standard
11
Series
55-CDS1
ATEX category 2 Build in magnet
D
125~300 125~200 Without magnet Built in magnet
Non-lube: 125, 140, 160, 180, 200, 250, 300 How to Order L N 160 300 R
Rod boot/Cushion
Cushion
55-CS1
N R H
No cushion With cushion on rod side With cushion on head side With both sides cushion
Rod type
W
Single rod Double rod
Mounting
B L F G C D T
Basic Foot Front flange Rear flange Single clevis Double clevis Centre trunnion
Non-lube
125
CS1-L12 CS1-F12 CS1-C12 CS1-D12
140
CS1-L14 CS1-F14 CS1-C14 CS1-D14
160
CS1-L16 CS1-F16 CS1-C16 CS1-D16
180
CS1-L18 CS1-F18 CS1-C18 CS1-D18
200
CS1-L20 CS1-F20 CS1-C20 CS1-D20
250
CS1-L25 CS1-F25 CS1-C25 CS1-D25
300
CS1-L30 CS1-F30 CS1-C30 CS1-D30
Order 2 foot brackets for one cylinder. When ordering the double clevis, the clevis pin and the cotter pin (2 pcs.) are attached.
For 55-CS1 When using an Auto switch, select the appropriate switch from the following table and order it separately. Applicable auto switch specifications Auto switch only conforms to Category 3. (II 3GD EEx nA II T5x -10C Ta +60C IP67) For detailed specifications on the D-A54, A67, and F5P, please refer to the relevant pages in Best Pneumatics. (Note: Reed auto switches for AC 100V and DC 100V are not within the specification.) Indicator Type Reed auto switch Solid state auto switch Model No. D-A54-588 D-A67-588 D-F5P-588 Electrical entry Wiring (Output) 2-wiring 3-wiring (PNP) Load voltage DC 24V 12V 24V or less 24V 5V,12V Note 1) AC Lead wire (m) Note1) 0.5 () 3 (L) 5 (Z) Applicable load
Grommet Grommet
Yes No Yes
IC circuit IC circuit
Relay PLC
When ordering a tie rod mounting type auto switch, also order a mounting bracket from the following list at the same time. Note 2) When mounting an auto switch on a 55- series (Category 2) Model, the ATEX category of the auto switch cylinder changes to Category 3, Auto switch mounting bracket/ Part no. (Tie rod mounting) which is the same category as the auto switch. Tube I.D. (mm) Auto switch
0.5m --- Nil (e.g.) D-A54-588 3 m --- L (e.g.) D-A54L-588 5 m --- Z (e.g.) D-A54Z-588
125,140 BT-12
160 BT-16
180 BT-18A
200 BT-20
12
Series
55-CS1
Specifications
Style ATEX category 1) Fluid Proof pressure 2) Max. operating pressure Min. operating pressure Piston speed Cushion Ambient and fluid temperature Thread tolerance Stroke length tolerance (mm) 250 or less:
+1.0 0, 2)
Non-lube
II 2GDc
Air (Non-lube) 1.57MPa 0.97MPa 0.05MPa 50 to 500 mm/s None, air cushion 0 to 60C (No freezing) JIS class 2 251 to 1,000:
+2.2 0, +1.4 0,
Note) All other specifications (dimensions, drawings, etc.) are the same as the non ATEX type.
2001 to 2400:
Basic, Foot, Front flange, Rear flange, Single clevis, Double clevis, Centre trunnion
Note 1) This cylinder can be used in zones 1 and 21 and in zones 2 and 22. If the cylinder is used with SMC category 3 type auto switch, then the cylinder can only be used in zones 2 and 22 and not in zones 1 and 21. Note 2) For the CDS1 diameter 180 and 200 the Proof pressure is 1.2MPa and the Max. operating pressure is 0.7MPa.
Accessories
Mounting Standard Clevis pin, Cotter pin Rod end nut Single knuckle joint Basic b b b Foot b b b Front flange b b b Rear flange b b b Single clevis b b b Double clevis b b b b Centre trunnion b b b
Symbol
Max. Stroke
Tube material Mounting bracket Aluminum alloy Basic Rear flange Single clevis Double clevis Centre trunnion 1000 or less 1000 or less 1200 or less Carbon steel tube Basic Rear flange Single clevis Double clevis 1000 or less 1000 or less 1200 or less 1200 or less 1200 or less 1200 or less 1200 or less With auto switch
(mm)
B, G, C, D, T
L, F
Bore
1600 or less 1600 or less 1600 or less 2000 or less 2000 or less 2400 or less 2400 or less
1000 or less 1000 or less 1200 or less 1200 or less 998 or less -
1400 or less 1400 or less 1400 or less 1500 or less 998 or less -
13
Series
55ATEX category 2
Port size
M5 (12~25 only)
12, 16, 20, 25, 32, 40, 50, 63, 80, 100, 125, 140, 160, 180, 200
How to Order
55-CQ2
30 D
Action
D Double acting C M
CDQ2 B 20
Body option
Standard (Rod end female thread) With rubber bumper Rod end male thread
Combination of body option is possible. (CM) Note2) All large bore cylinder 125 to 200 have C (rubber bumper) as standard.
Built-in magnet
None
Stroke (mm)
Bore size (mm) Standard stroke (mm) 5, 10, 15, 20, 25, 30 5, 10, 15, 20, 25, 30, 35, 40, 45, 50 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 75, 100 10, 20, 30, 40, 50, 75, 100, 125, 150, 175, 200, 250, 300
Built-in magnet
Mounting
B A L Through -hole (Standard) Both ends tapped Foot F G D Front flange Rear flange Double clevis
Only B type (Through-hole and both ends tapped) is available for large bore cylinder 125 to 200.
Bore size
12 16 20 25 32 12mm 16mm 20mm 25mm 32mm 40 50 63 80 100 40mm 50mm 63mm 80mm 100mm 125 140 160 180 200 125mm 140mm 160mm 180mm 200mm
For 55-CDQ2 When using an Auto switch, select the appropriate switch from the following table and order it separately.
Applicable auto switch specifications Auto switch only conforms to Category 3. (II 3GD EEx nA II T5x -10C Ta +60C IP67) For detailed specifications on the D-A73(H), A80(H), F7P(V), A93(V), A90(V), Z73, Z80, M9P(V) and Y7P(V), please refer to the relevant pages in Best Pneumatics. (Note: Reed auto switches for AC 100V and DC 100V are not within the specification. Also for D-M9P(V) type, see D-F9P(V) type specifications) Type Model No. Direct mounting Rail mounting 32 to 100 32 to 100 Indicator Electrical entry Wiring (Output) 24V 2-wiring 24V Load voltage DC 12V 48V or less 48V or less IC circuit IC circuit IC circuit Relay PLC 12V AC 0.5 () Lead wire (m) 3 (L) 5 (Z) Applicable load
Note 4) 2 pcs. per cylinder should be ordered when foot brackets are required. Note 5) Each package contains the following parts. Foot, Flange: Body mounting bolt Double clevis: Clevis pin, C shape snap ring for axis, body mounting bolt Note 6) Package for double clevis contains clevis pin and snap ring.
D-A73-588 D-A93V-588 Grommet (Perpendicular entry) D-A80-588 D-A90V-588 Reed auto switch D-A73H-588 D-A93-588 D-Z73-588 Grommet (In-line entry) D-A80H-588 D-A90-588 D-Z80-588 Grommet D-F7PV-588 D-M9PV-588 D-Y7PV-588 (Perpendicular entry) Solid state auto switch Grommet D-F7P-588 D-M9P-588 D-Y7P-588 (In-line entry) Lead wire length 0.5m --- Nil (e.g.) D-A73-588 3 m --- L (e.g.) D-A73L-588 5 m --- Z (e.g.) D-A73Z-588
Note 1)
Note 2) When mounting an auto switch on a 55- series (Category 2) Model, the ATEX category of the auto switch cylinder changes to Category 3, which is the same category as the auto switch.
When ordering a rail mounting type auto switch, also order a mounting bracket from the following list at the same time. Auto switch mounting bracket/ Part no. (Rail mounting type)
14
Series
55-CQ2
Style
Bore size (mm) Mounting
Through-hole (Standard)
12
16
20
25
32
40
50
63
80
100
125
140
160
180
200
Piping
Screw-in style
M5
M5
M5
M5
M5 G1/8
G1/8 G1/4 G1/4 G3/8 G3/8 G3/8 G3/8 G3/8 G1/2 G1/2
Specifications
Bore size (mm) ATEX category 1) Style Fluid Proof pressure Max. operating pressure Min. operating pressure Ambient and fluid temperature Cushion Rod end thread Tolerance of rod end thread Tolerance of stroke length Mounting Piston speed
+1.0 0
12
16
20
25
32
40
50
63
80
100
125
140
160
180
200
II 2GDc
Pneumatic (Non-lube) 1.5MPa 1.0MPa 0.07MPa 0.05MPa 10C to 60C (No freezing) None, rubber bumper Male thread, Female thread JIS class 2
+1.4 0
1.05MPa 0.7MPa
Rubber bumper
Through-hole, Both end tapped, Foot, Front flange, rear flange, Double clevis 50 to 500mm/s
Note 1) This cylinder can be used in zones 1 and 21 and in zones 2 and 22. If the cylinder is used with SMC category 3 type auto switch, then the cylinder can only be used in zones 2 and 22 and not in zones 1 and 21.
Note) All other specifications (dimensions, drawings, etc.) are the same as the non ATEX type.
15
Series
55-CXS W M 20
ATEX category 2 Dual rod cylinder Type
W Single rod Double rod
55-CXS/W
How to Order
Standard Strokes
CXS
Bore size Standard stroke 10, 20, 30, 40, 50 10, 15, 20, 25, 30, 35, 40, 45, 50, 60, 70, 75
(mm)
6 10 15 20 25 32
CXSW
Bore size
Bearing
M L Slide bearing Ball bushing bearing
10, 15, 20, 25, 30, 35, 40, 45, 50, 60, 70, 75, 80, 90, 100 110 to 200
(mm)
Bore size
6 6mm 10 10mm 15 15mm 20 20mm 25 25mm 32 32mm
Standard stroke 10, 20, 30, 40, 50 10, 20, 30, 40, 50
6 10 15 20 25 32
Bore size 10~20 25~32 25~32
TF
Type M thread Rc G
110 to 200
CXS Specifications
Bore size (mm) ATEX category 1) Min. operating pressure Max. operating pressure Proof pressure Fluid Ambient and fluid temperature Piston speed Piping port Stroke adjustable range 0.15MPa
10
15
20
25
32
II 2GDc
0.1MPa
1.05MPa Air (Non-lube) 10 to 60C (No freezing) 30 to 300 30 to 800 mm/s mm/s M5 30 to 700 mm/s 30 to 600 mm/s Rc, G1/8
0 to 5 mm to the standard stroke Slide bearing, Ball bushing bearing (Same dimensions) Rubber bumper
Note) All other specifications (dimensions, drawings, etc.) are the same as the non ATEX type.
Bearing Cushion
CXSW Specifications
Bore size (mm) ATEX category 1) Fluid Min. operating pressure Max. operating pressure Proof pressure Ambient and fluid temperature Piston speed Piping port Stroke adjustable range Bearing Cushion M5 0.15MPa 0.7MPa 1.05MPa 10 to 60C (No freezing) 50 to 500mm/s Rc, G1/8 0 to 10mm (Extension side: 5mm, Retraction side: 5mm) Slide bearing, Ball bushing (Same dimensions) Rubber bumper
10
15
20
25
32
II 2GDc
Air (Non-lube)
Note 1) This cylinder can be used in zones 1 and 21 and in zones 2 and 22. If the cylinder is used with SMC category 3 type auto switch, then the cylinder can only be used in zones 2 and 22 and not in zones 1 and 21.
16
Series
55-CXS
For 55-CXS When using an Auto switch, select the appropriate switch from the following table and order it separately. Applicable auto switch specifications Auto switch only conforms to Category 3. (II 3GD EEx nA II T5x -10C Ta +60C IP67) For detailed specifications on the D-Z73, Z80, Y7P, and Y7PV, please refer to the relevant pages in Best Pneumatics. (Note: Reed auto switches for AC 100V and DC 100V are not within the specification.) Indicator Type Model No. D-Z73-588 D-Z80-588 D-Y7P-588 D-Y7PV-588 Electrical entry Wiring (Output) Load voltage DC 24V 2-wiring 24V or less 12V 48V 48V or less IC circuit Relay PLC Yes Grommet (Perpendicular) 3-wiring (PNP) 24V 5V,12V IC circuit AC 0.5 () Lead wire (m) 3 (L) 5 (Z) Applicable load
0.5m --- Nil (e.g.) D-Z73-588 3 m --- L (e.g.) D-Z73L-588 5 m --- Z (e.g.) D-Z73Z-588
Note 1)
Note 2) When mounting an auto switch on a 55- series (Category 2) Model, the ATEX category of the auto switch cylinder changes to Category 3, which is the same category as the auto switch.
17
Series
Basic Type
Bore size
10 16 20 25 32 40 50 63 80 100
10mm 16mm 20mm 25mm 32mm 40mm 50mm 63mm 80mm 100mm
Basic Type/10, 16, 20, 25, 32, 40, 50, 63, 80, 100
How to Order
55-MY1B
300
Stroke
Refer to the standard stroke table below. Bore size 10~20 25~100
55-MY1B 25
Basic type Piping thread
Symbol
ATEX category 2
TN TF
Piping
G Standard type Centralized piping type
Standard strokes
Bore size (mm) Standard stroke (mm) 100, 200, 300, 400, 500, 600, 700 800, 900, 1000, 1200, 1400, 1600 1800, 2000 Max. manufacturable stroke (mm) 3000 5000
Specifications
Bore size (mm) ATEX category 1) Fluid Action Operating pressure range Proof pressure Ambient and fluid temperature Cushion Lubricaton 1000 or less+1.8 0 Stroke length tolerance 1001 to 3000+2.8 0 Port size Front/Side ports M5 x 0.8 100 to 500 mm/s
Rubber bumper
0.2 to 0.8MPa
10
16
20
25
32
40
50
63
80
100
II 2Gc
Symbol
Note) All other specifications (dimensions, drawings, etc.) are the same as the non ATEX type.
Note 1) This cylinder can be used in zone 1 and 2. For 55-MY1B If the cylinder is used with SMC category 3 type auto switch, then the When using an Auto switch, select the appropriate cylinder can only be used in zone 2 and not in zone 1. switch from the following table and order it separately. Applicable auto switch specifications Auto switch only conforms to Category 3. (II 3GD EEx nA II T5x -10C Ta +60C IP67) For detailed specifications on the D-A93(V), A90(V), Z73, Z80, M9P(V) and Y7PV, please refer to the relevant pages in Best Pneumatics. (Note: Reed auto switches for AC 100V and DC 100V are not within the specification. Also for D-M9P(V) type, see D-F9P(V) type specifications.) Lead wire (m) Load voltage Model No. Wiring Applicable Electrical entry Type 0.5 3 5 load DC AC (Output) () (L) (Z) 25 to 100 10 to 20 Yes 24V 12V D-A93V-588 Grommet (Perpendicular entry) No 24V or less 48V 48V or less D-A90V-588 IC circuit Reed 2-wiring auto switch D-A93-588 Yes 24V 12V D-Z73-588 Grommet Relay (In-line entry) No IC circuit 24V or less 48V 48V or less D-A90-588 D-Z80-588 PLC Solid state auto switch D-M9PV-588 D-Y7PV-588 D-M9P-588 Grommet (Perpendicular entry) Yes 3-wiring Grommet (PNP) D-Y7P-588 (In-line entry) Indicator 24V 5V, 12V IC circuit
0.5m --- Nil (e.g.) D-A93-588 3 m --- L (e.g.) D-A93L-588 5 m --- Z (e.g.) D-A93Z-588
Note 1)
Note 2) When mounting an auto switch on a 55- series (Category 2) Model, the ATEX category of the auto switch cylinder changes to Category 3, which is the same category as the auto switch.
18
Series
55-MY1M
55-MY1M 25
Slide bearing guide type
300
Stroke
Refer to the standard stroke table below.
ATEX category 2
Piping
G Standard type Centralized piping type
Standard strokes
Bore size (mm) Standard stroke (mm) 100, 200, 300, 400, 500, 600, 700 800, 900, 1000, 1200, 1400, 1600 1800, 2000 Max. manufacturable stroke (mm) 3000 5000
Bore size
16 20 25 32 40 50 63
16mm 20mm 25mm 32mm 40mm 50mm 63mm
Piping
Symbol
TN TF
Specifications
Bore size (mm) ATEX category 1) Fluid Action Operating pressure range Proof pressure Ambient and fluid temperature Cushion Lubrication
16
20
25
32
40
50
63
II 2Gc
Symbol
M5 x 0.8
Note) All other specifications (dimensions, drawings, etc.) are the same as the non ATEX type.
Note 1) This cylinder can be used in zones 1 and 2. If the cylinder is used with SMC category 3 type auto switch, then the cylinder can only be used in zone 2 and not in zone 1.
For 55-MY1M When using an Auto switch, select the appropriate switch from the following table and order it separately. Applicable auto switch specifications Auto switch only conforms to Category 3. (II 3GD EEx nA II T5x -10C Ta +60C IP67) For detailed specifications on the D-A93(V), A90(V), Z73, Z80, M9P(V) and Y7PV, please refer to the relevant pages in Best Pneumatics. (Note: Reed auto switches for AC 100V and DC 100V are not within the specification. Also for D-M9P(V) type, see D-F9P(V) type specifications.) Type Model No. 10 to 20 D-A93V-588 D-A90V-588 Reed auto switch D-A93-588 D-A90-588 Solid state auto switch D-Z73-588 D-Z80-588 25 to 100 Indicator Electrical entry Wiring (Output) 24V 2-wiring 24V Load voltage DC 12V 48V or less 48V or less IC circuit IC circuit IC circuit Relay PLC 12V AC 0.5 () Lead wire (m) 3 (L) 5 (Z) Applicable load
Grommet (Perpendicular entry) Yes 3-wiring Grommet (PNP) D-Y7P-588 (In-line entry)
0.5m --- Nil (e.g.) D-A93-588 3 m --- L (e.g.) D-A93L-588 5 m --- Z (e.g.) D-A93Z-588
Note 1)
Note 2) When mounting an auto switch on a 55- series (Category 2) Model, the ATEX category of the auto switch cylinder changes to Category 3, which is the same category as the auto switch.
19
Series
High Precision Guide Type
55-MY1H
300
Stroke
Refer to the standard stroke table below.
55-MY1H 25
High precision guide type Bore size
Maximum manufacturable stroke (mm) 1000 1500 10 16 20 25 32 40
10mm 16mm 20mm 25mm 32mm 40mm
ATEX category 2
Piping
G Standard type Centralized piping type
Standard strokes
Bore size (mm) Standard stroke
(mm)
50, 100, 150, 200, 300, 350, 400, 450, 500, 550, 600
Piping
Symbol
TN TF
Specifications
Bore size (mm) ATEX category 1) Fluid Action Operating pressure range Proof pressure Ambient and fluid temperature Cushion Lubrication
Rubber bumper
0.2 to 0.8MPa
10
16
20
25
32
40
II 2Gc
75C (T6) Ta 5 to 40C 95C (T5) Ta 40 to 60C Air Double acting 0.1 to 0.8MPa 1.2MPa 5 to 60C Air cushion Non-lube +1.8 0
Symbol
Stroke length tolerance Port size Front/Side ports 100 to 500 mm/s M5 x 0.8
Note) All other specifications (dimensions, drawings, etc.) are the same as the non ATEX type.
Note 1) This cylinder can be used in zone 1 and 2. If the cylinder is used with SMC category 3 type auto switch, then the cylinder can only be used in zone 2 and not in zone 1.
For 55-MY1H When using an Auto switch, select the appropriate switch from the following table and order it separately. Applicable auto switch specifications Auto switch only conforms to Category 3. (II 3GD EEx nA II T5x -10C Ta +60C IP67) For detailed specifications on the D-A93(V), A90(V), Z73, Z80, M9P(V) and Y7PV, please refer to the relevant pages in Best Pneumatics. (Note: Reed auto switches for AC 100V and DC 100V are not within the specification. Also for D-M9P(V) type, see D-F9P(V) type specifications.) Type Model No. 10 to 20 D-A93V-588 Reed auto switch D-A90V-588 D-A93-588 D-A90-588 Solid state auto switch D-Z73-588 D-Z80-588 25 to 100 Indicator Electrical entry Wiring (Output) 24V 2-wiring 24V Load voltage DC 12V 48V or less 48V or less IC circuit IC circuit IC circuit Relay PLC 12V AC 0.5 () Lead wire (m) 3 (L) 5 (Z) Applicable load
Grommet (Perpendicular entry) Yes 3-wiring Grommet (PNP) D-Y7P-588 (In-line entry)
0.5m --- Nil (e.g.) D-A93-588 3 m --- L (e.g.) D-A93L-588 5 m --- Z (e.g.) D-A93Z-588
Note 1)
Note 2) When mounting an auto switch on a 55- series (Category 2) Model, the ATEX category of the auto switch cylinder changes to Category 3, which is the same category as the auto switch.
20
21
Series 55-CRB1
Sizes: 50, 63, 80, 100 How to Order
55-CRB1 B W 80
ATEX category 2
Size
50 63 80 100
90 S
Mounting
B L Basic type Foot type
Thread Port
Rc(PT)
XF XN
G(PF) NPT
Refer to Table 1 below if only foot assembly is required separately. Foot accesory is shipped together with the actuator but not mounted on it.
Shaft type
W Double shaft (long shaft key & four chamfers)
Rotation
Classification
Symbol Single vane 90 90 180 180 270 270 100 100 190 190 280 280 S D
Optional Standard
Vane type
Single vane Double vane
A port
B port
B port
A port
Side ports
Axial ports
Body end of the short-shaft side
22
Rotary Actuator
Vane Type
Series 55-CRB1
Specifications
Radial force Model (Size) Vane type
ATEX category
1)
+4 +4
II 2GDc
90 0 , 180 0 , 270 0 +4 +4 100 +4 0 , 190 0 , 280 0
+4
Rotation Fluid
Size: 100 Size: 80
Standard Optional
Air (non-lube)
1.5MPa 5 to 60C 1.0MPa 0.15MPa 0.1 to 1 0.082 245 196 0.12 390 340 0.398 490 490 0.6 588 539 0.112 245 196 0.16 390 340 0.54 490 490 0.811 588 539
Thr
ust
fo
rce
Size: 50
Max. operating pressure (MPa) Min. operating pressure (MPa) Speed regulation range (sec/90)
Allowable kinetic energy (J)
JIS symbol
Allowable Shaft radial load (N) load Allowable thrust load (N) Bearing type Port position Size Side ports Axial ports Mounting
Ball bearing
Basic, Foot
Note) All other specifications (dimensions, drawings, etc.) are the same as the non ATEX type.
23
Series 55-CRB2
Sizes: 10, 15, 20, 30, 40 How to Order
55-CRB2 B W 10
ATEX category 2
180 S E
Connecting port position
Mounting
Basic type B Flange type F1) When ordering "F" mounting type, flange is shipped together with the actuator, but not mounted. Flange can be mounted at 60 degrees intervals. Note1) Not available for size 40.
Size
10 15 20 30 40
Vane type
S D Single vane Double vane Fittings are sold separately.
Rotation
Vane type Symbol Single vane Double vane
90 180 270 90 100
Rotation
90 180 270 90 100
24
Rotary Actuator
Vane Type
Series 55-CRB2
Radial force
CRB2BW10-S CRB2BW15-S CRB2BW20-S CRB2BW30-S CRB2BW40-S Single vane 130C (T4) Ta 5 to 40C
II 2Gc
Thr
ust
e orc
Rotation Fluid Proof pressure (MPa) Ambient and fluid temperature Max. operating pressure (MPa) Min. operating pressure (MPa) Speed regulation range (sec/90) Note 2) Allowable kinetic energy (J) Shaft Allowable radial load (N) load Allowable thrust load (N) Bearing type Port position Side ports Size Axial ports Shaft type
5 to 60C
0.7 0.2 0.03 to 0.3 0.00015 15 10 0.001 15 10 0.003 25 20 1.0 0.15 0.04 to 0.3 0.02 30 25 0.07 to 0.5 0.04 60 40
Note) All other specifications (dimensions, drawings, etc.) are the same as the non ATEX type.
Mounting
Note 1) This rotary actuator can be used in zones 1 and 2.
Basic, Flange
Basic
CRB2BW10-D CRB2BW15-D CRB2BW20-D CRB2BW30-D CRB2BW40-D Double vane 130C (T4) Ta 5 to 40C 150C (T3) Ta 40 to 60C 90, 100 1.5
II 2Gc
Rotation
JIS symbol
Fluid Proof pressure (MPa) Ambient and fluid temperature Max. operating pressure (MPa) Min. operating pressure (MPa) Speed regulation range (sec/90) Note 2) Allowable kinetic energy (J) Shaft Allowable radial load (N) load Allowable thrust load (N) Bearing type Port position Port size (Side ports, Axial ports) Shaft type Mounting
M3 0.0003 15 10 0.2 0.03 to 0.3 0.0012 15 10 0.7 1.05
Double shaft (double shaft with single flat on both shafts) Basic, Flange
Basic
The following notes apply to both Single and Double Vane Specification tables above. Note 2) Make sure to operate within the speed regulation range. Exceeding the maximum speed (0.3 sec/90) can cause the unit to stick or not operate.
25
Series
55-CRBU2
180 S E
Connecting port position
E Side ports Axial ports Side ports Axial ports
How to Order
55-CRBU2 W 10
ATEX category 2
Free-mounting
Size
10 15 20 30 40
Shaft type
W Double shaft with single flat (sizes 10 to 30) Long shaft key, Short shaft with single flat (size 40) Single vane Double vane
Vane type
S D Single vane Double vane
Rotation
Vane type Symbol Rotation
90 180 270 90 100 90 180 270 90 100
26
Rotary Actuator
Free-Mounting Type
Series 55-CRBU2
Radial force
II 2Gc
Rotation
or st f ce
150C (T3) Ta 40 to 60C 90, 180, 270 Air (non-lube) 1.5 5 to 60C 1.0 0.15 0.04 to 0.3 0.003 25 20 Ball bearing 0.02 30 25 0.07 to 0.5 0.04 60 40
Fluid Proof pressure (MPa) Ambient and fluid temperature Max. operating pressure (MPa) Min. operating pressure (MPa) Speed regulation range (sec/90) Note 2) Allowable kinetic energy (J) Shaft Allowable radial load (N) load Allowable thrust load (N) Bearing type
0.00015 15 10 0.2 0.03 to 0.3 0.001 0.7 1.05
Thr
Note) All other specifications (dimensions, drawings, etc.) are the same as the non ATEX type.
II 2Gc
Rotation Fluid Proof pressure (MPa) Ambient and fluid temperature Max. operating pressure (MPa)
0.7 0.2 0.0003 15 10 0.03 to 0.3 0.0012 1.05
Air (non-lube) 5 to 60C 1.0 0.15 0.04 to 0.3 0.0033 25 20 Ball bearing 0.02 30 25 0.07 to 0.5 0.04 60 40
JIS symbol
Min. operating pressure (MPa) Speed regulation range (sec/90) Note 2) Allowable kinetic energy (J) Shaft Allowable radial load (N) load Allowable thrust load (N) Bearing type Port position Port size Shaft type Side ports Axial ports
The following notes apply to both Single and Double Vane Specification tables above. Note 2) Make sure to operate within the speed regulation range. Exceeding the maximum speeds can cause the unit to stick or not operate.
27
Series
ATEX category 2
Built-in magnet
D
55-CRQ2
How to Order
55-CDRQ2B S 20
None Magnet
90
Air cushion
Air cushion Without 20, 30, 40 Without With C Sizes 10, 15
Shaft type
S W Single shaft with one chamfer Single shaft with key Double shaft with one chamfer Double shaft with key 10, 15 20~40 10, 15 20~40
Size
10 15 20 30 40
Rotation
90 180 80 to 100 170 to 190
Specifications
Size ATEX category 1) Fluid Maximum operating pressure Minimum operating pressure Ambient and fluid temperature Cushion Angle adjustment Rotation Port size Mounting brackets Output Nm at 0.5 MPa 0.3 0.75 M5 x 0.8 1.8 Rubber bumper 5 80 to 100, 170 to 190 Rc, G, NPT, NPT(F) 1/8 Basic type 3.1 5.3 0.7MPa 0.15MPa 10 15 20 30 40
II 2Gc
Air (unlubricated)
Note) All other specifications (dimensions, drawings, etc.) are the same as the non ATEX type.
Note 1) This cylinder can be used in zones 1 and 2. If the cylinder is used with SMC category 3 type auto switch, then the cylinder can only be used in zone 2 and not in zone 1.
Rotation time (s/90) 0.2 to 0.7 0.2 to 0.7 0.2 to 1 0.2 to 1 0.2 to 1
10 15 20 30 40
28
Series 55-CRQ2
For 55-CRQ2 When using an Auto switch, select the appropriate switch from the following table and order it separately. Applicable auto switch specifications Auto switch only conforms to Category 3. (II 3GD EEx nA II T5x -10C Ta +60C IP67) For detailed specifications on the D-A93A, A90, A93V, A90V, M9P, and M9PV, please refer to the relevant pages in Best Pneumatics. (Note: Reed auto switches for AC 100V and DC 100V are not within the specification.) Indicator Type Model No. D-A93-588 Reed auto switch D-A90-588 D-A93V-588 D-A90V-588 Solid state auto switch Lead wire length D-M9P-588 D-M9PV-588 Electrical entry Grommet (In-line) Grommet (Perpendicular) Grommet (In-line) Grommet (Perpendicular) Wiring (Output) 24V 2-wiring 24V Load voltage DC 12V 48V or less 48V or less IC circuit IC circuit IC circuit Relay PLC 12V AC 0.5 () Lead wire (m) 3 (L) 5 (Z) Applicable load
0.5m --- Nil (e.g.) D-A93-588 3 m --- L (e.g.) D-A93L-588 5 m --- Z (e.g.) D-A93Z-588
Note 1)
Note 2) When mounting an auto switch on a 55- series (Category 2) Model, the ATEX category of the auto switch cylinder changes to Category 3, which is the same category as the auto switch.
29
Series 56-CRB1
Sizes: 50, 63, 80, 100 How to Order
56-CDRB1 B W 80
ATEX category 3
With auto switch unit
D Without switch unit With switch unit
90 S
Size
50 63 80 100
Thread Port
Rc(PT)
XF XN
G(PF) NPT
Refer to Table 1 below if only foot assembly is required separately. Foot accesory is shipped together with the actuator but not mounted on it.
Shaft type
W Double shaft (long shaft key & four chamfers)
Rotation
Classification
Symbol Single vane 90 90 180 180 270 270 100 100 190 190 280 280 S D
Optional Standard
A port
B port
B port
A port
Side ports
Axial ports
Body end of the short-shaft side
Vane type
Single vane Double vane
For 56-CDRB1 When using an Auto switch, select the appropriate switch from the following table and order it separately. Applicable auto switch specifications Auto switch only conforms to Category 3. (II 3GD EEx nA II T5x -10C Ta +60C IP67) For detailed specifications on the D-R73, R80, and S7P, please refer to the relevant pages in Best Pneumatics. (Note: Reed auto switches for AC 100V and DC 100V are not within the specification.) Indicator Type Model No. D-R73-588 D-R80-588 Electrical entry Wiring (Output) Load voltage DC AC 0.5 () Lead wire (m) 3 (L) 5 (Z) Applicable load
Yes Grommet (In-line) No 2-wiring 24V 5V,12V 24V or less IC circuit Relay PLC
D-S7P-588
Grommet (In-line)
Yes
3-wiring (PNP)
24V 5V,12V
IC circuit
0.5m --- Nil (e.g.) D-R73-588 3 m --- L (e.g.) D-R73L-588 5 m --- Z (e.g.) D-R73Z-588
Note) Refer to the table below for the ATEX temperature class of a rotary actuator (56-CDRB1) with an autoswitch mounted to it.
Normal temperature range (5C to 40C) Special temperature range (40C to 60C)
Rotary Actuator T6 T4
Auto switch T5 T5
30
Rotary Actuator
Vane Type
Series 56-CRB1
Specifications
Radial force Model (Size) Vane type
ATEX category
1)
II 3G
90 0 , 180 0 , 270 0 +4 +4 100 +4 0 , 190 0 , 280 0
+4 +4 +4
Rotation Fluid
Size: 100 Size: 80
Standard Optional
Air (non-lube)
1.5MPa 5 to 60C 1.0MPa 0.15MPa 0.1 to 1 0.082 245 196 0.12 390 340 0.398 490 490 0.6 588 539 0.112 245 196 0.16 390 340 0.54 490 490 0.811 588 539
Thr
ust
fo
rce
Size: 50
Max. operating pressure (MPa) Min. operating pressure (MPa) Speed regulation range (sec/90)
Allowable kinetic energy (J)
JIS symbol
Allowable Shaft radial load (N) load Allowable thrust load (N) Bearing type Port position Size Side ports Axial ports Mounting
Ball bearing
Basic, Foot
Note) All other specifications (dimensions, drawings, etc.) are the same as the non ATEX type.
31
Series 56-CRB2
Sizes: 10, 15, 20, 30, 40 How to Order
56-CDRB2 B W 10
ATEX category 3
180 S
Connecting port position
Size
10 15 20 30 40
Mounting
Basic type B Flange type F1) When ordering "F" mounting type, flange is shipped together with the actuator, but not mounted. Flange can be mounted at 60 degrees intervals. Note1) Not available for size 40.
Vane type
S D Single vane Double vane
Rotation
90 180 270 90 100
For 56-CDRB2 When using an Auto switch, select the appropriate switch from the following table and order it separately. Applicable auto switch specifications Auto switch only conforms to Category 3. (II 3GD EEx nA II T5x -10C Ta +60C IP67) For detailed specifications on the D-93A, 90A, S9P, S9PV, R73, R80, and S7P, please refer to the relevant pages in Best Pneumatics. (Note: Reed auto switches for AC 100V and DC 100V are not within the specification.) Applicable Size Indicator Type Reed auto switch Model No. D-93A-588 D-90A-588 Electrical entry Grommet (In-line) Wiring (Output) 2-wiring 3-wiring (PNP) 2-wiring 3-wiring (PNP) 24V 24V Load voltage DC 5V, 12V 24V or less 24V 5V, 12V 5V, 12V 24V or less 5V, 12V IC circuit IC circuit IC circuit IC circuit IC circuit Relay PLC AC 0.5 () Lead wire (m) 3 (L) 5 (Z) Applicable load
Yes No
10, 15
20, 30, 40
Grommet (In-line) Solid state D-S9P-588 Yes auto switch D-S9PV-588 Grommet (Perpendicular) D-R73-588 Yes Reed Grommet auto switch D-R80-588 (In-line) No Solid state Grommet Yes D-S7P-588 auto switch (In-line) 0.5m --- Nil (e.g.) D-R73-588 3 m --- L (e.g.) D-R73L-588 5 m --- Z (e.g.) D-R73Z-588
Note) Refer to the table below for the ATEX temperature class of a rotary actuator (56-CDRB1) with an autoswitch mounted to it.
Normal temperature range (5C to 40C) Special temperature range (40C to 60C)
Rotary Actuator T5 T4
Auto switch T5 T5
32
Rotary Actuator
Vane Type
Series 56-CRB2
Radial force
CRB2BW10-S CRB2BW15-S CRB2BW20-S CRB2BW30-S CRB2BW40-S Single vane 100C (T5) Ta 5 to 40C
II 3G
Thr
us
rc t fo
Rotation Fluid Proof pressure (MPa) Ambient and fluid temperature Max. operating pressure (MPa) Min. operating pressure (MPa) Speed regulation range (sec/90) Note 2) Allowable kinetic energy (J) Shaft Allowable radial load (N) load Allowable thrust load (N) Bearing type Port position Side ports Size Axial ports Shaft type
5 to 60C
0.7 0.2 0.03 to 0.3 0.00015 15 10 0.001 15 10 0.003 25 20 1.0 0.15 0.04 to 0.3 0.02 30 25 0.07 to 0.5 0.04 60 40
Note) All other specifications (dimensions, drawings, etc.) are the same as the non ATEX type.
Basic, Flange
Mountable (Side ports only)
Basic
CRB2BW10-D CRB2BW15-D CRB2BW20-D CRB2BW30-D CRB2BW40-D Double vane 100C (T5) Ta 5 to 40C 120C (T4) Ta 40 to 60C 90, 100 1.5
II 3G
Rotation
JIS symbol
Fluid Proof pressure (MPa) Ambient and fluid temperature Max. operating pressure (MPa) Min. operating pressure (MPa) Speed regulation range (sec/90) Note 2) Allowable kinetic energy (J) Shaft Allowable radial load (N) load Allowable thrust load (N) Bearing type Port position Port size (Side ports, Axial ports) Shaft type Mounting Auto switch
M3 0.0003 15 10 0.2 0.03 to 0.3 0.0012 15 10 0.7 1.05
Double shaft (double shaft with single flat on both shafts) Basic, Flange
Mountable (Side ports only) Basic
The following notes apply to both Single and Double Vane Specification tables above. Note 2) Make sure to operate within the speed regulation range. Exceeding the maximum speed (0.3 sec/90) can cause the unit to stick or not operate.
33
Series
56-CRBU2
How to Order
56-CDRBU2 W 10
ATEX category 3
180 S
Connecting port position
Size
10 15 20 30 40
Vane type
S D Single vane Double vane
Free-mounting
Shaft type
W Double shaft with single flat (sizes 10 to 30) Long shaft key, Short shaft with single flat (size 40)
Rotation
Vane type Symbol Rotation Single vane Double vane
90 180 270 90 100 90 180 270 90 100
For 56-CDRBU2 When using an Auto switch, select the appropriate switch from the following table and order it separately. Applicable auto switch specifications Auto switch only conforms to Category 3. (II 3GD EEx nA II T5x -10C Ta +60C IP67) For detailed specifications on the D-93A, 90A, S9P, S9PV, R73, R80, and S7P, please refer to the relevant pages in Best Pneumatics. (Note: Reed auto switches for AC 100V and DC 100V are not within the specification.) Applicable Size Indicator Type Reed auto switch Model No. D-93A-588 D-90A-588 Electrical entry Grommet (In-line) Wiring (Output) 2-wiring 3-wiring (PNP) 2-wiring 3-wiring (PNP) 24V Load voltage DC 5V, 12V 24V or less 24V 24V 24V 5V, 12V 5V, 12V 24V or less 5V, 12V IC circuit IC circuit Relay PLC AC 0.5 () Lead wire (m) 3 (L) 5 (Z) Applicable load
Yes No
10, 15
20, 30, 40
Grommet (In-line) Solid state D-S9P-588 Yes auto switch D-S9PV-588 Grommet (Perpendicular) D-R73-588 Yes Reed Grommet auto switch D-R80-588 (In-line) No Solid state Grommet Yes D-S7P-588 auto switch (In-line) 0.5m --- Nil (e.g.) D-R73-588 3 m --- L (e.g.) D-R73L-588 5 m --- Z (e.g.) D-R73Z-588
IC circuit IC circuit
Note) Refer to the table below for the ATEX temperature class of a rotary actuator (56-CDRB1) with an autoswitch mounted to it.
Normal temperature range (5C to 40C) Special temperature range (40C to 60C)
Rotary Actuator T5 T4
Auto switch T5 T5
34
Rotary Actuator
Free-Mounting Type
Series 56-CRBU2
Radial force
II 3G
Rotation
or st f ce
120C (T4) Ta 40 to 60C 90, 180, 270 Air (non-lube) 1.5 5 to 60C 1.0 0.15 0.04 to 0.3 0.003 25 20 Ball bearing 0.02 30 25 0.07 to 0.5 0.04 60 40
Fluid Proof pressure (MPa) Ambient and fluid temperature Max. operating pressure (MPa) Min. operating pressure (MPa) Speed regulation range (sec/90) Note 2) Allowable kinetic energy (J) Shaft Allowable radial load (N) load Allowable thrust load (N) Bearing type
0.00015 15 10 0.2 0.03 to 0.3 0.001 0.7 1.05
Thr
Note) All other specifications (dimensions, drawings, etc.) are the same as the non ATEX type.
Note 1) This rotary actuator can be used in zones 2 and not in zone 1.
II 3G
Rotation Fluid Proof pressure (MPa) Ambient and fluid temperature Max. operating pressure (MPa) Min. operating pressure (MPa) Speed regulation range (sec/90) Note 2) Allowable kinetic energy (J) Shaft Allowable radial load (N) load Allowable thrust load (N) Bearing type Port position Port size Shaft type Side ports Axial ports
M3 0.0003 15 10 0.2 0.03 to 0.3 0.0012 1.05
Air (non-lube) 5 to 60C 0.7 1.0 0.15 0.04 to 0.3 0.0033 25 20 Ball bearing 0.02 30 25 0.07 to 0.5 0.04 60 40
JIS symbol
The following notes apply to both Single and Double Vane Specification tables above. Note 2) Make sure to operate within the speed regulation range. Exceeding the maximum speeds can cause the unit to stick or not operate.
35
D-M9P(V)-588
Auto Switch Specifications
PLC: Programmable Logic Controller
Note) All other specifications (dimensions, drawings, etc.) are the same as the non ATEX type.
Lead wire: oil-proof heavy-duty vinyl cable 2.7 x 3.2 with elliptic cross-section, 0.15 mm2, two cores (D-M9B), or three cores (D-M9N and D-M9P) This category 3 type autoswitch can only be used in zones 2 and 22.
D-M9 P V L -588
Series Model Number Suffix for ATEX certified CAT.3 Lead wire length
Nil L Z 0.5m 3m 5m
Electrical entry
Nil V In-line Perpendicular
36
D-C73/D-C80-588
Grommet
Specifications
D-C7 (With indicator light)
Auto switch model number ATEX Category Application Load voltage Max. load current and range Contact protection circuit Internal voltage drop Indicator light
D-C73
II 3GD EEx nA II T5 X -10CTa+60C IP67
Relay/PLC 24V DC 5 to 40mA None 2.4V ON: When red light emitting diode
D-C80
II 3GD EEx nA II T5 X -10CTa+60C IP67
Relay/PLC/IC circuit or less None
AC 48V DC
Note) All other specifications (dimensions, drawings, etc.) are the same as the non ATEX type.
50mA
40mA
1 or less (Including 3m lead wire) Internal resistance This category 3 type autoswitch can only be used in zones 2 and 22.
How to order
CD-P12
OUT() Blue(Black)
D-C80
Reed switch Contact protective box CD-P11 CD-P12
OUT( ) Blue(Black) OUT() Brown(Red)
D-C
-588
Suffix for ATEX certified CAT.3
Note) q In the case operation load is an inductive load. w In the case the wiring length to load is more than 5m. Be sure to use the auto switch with the contact protection box in any case mentioned above.
Switch No.
73 80 With indicator lamp Without indicator lamp
37
D-A73(H)/D-A80(H)-588
Grommet
Specifications D-A7 (With indicator light)
Auto switch model number ATEX Category Application Load voltage Load current range Contact protection circuit Internal voltage drop Indicator light PLC: Programmable Logic Controller
D-A73
II 3GD EEx nA II T5 X -10CTa+60C IP67
Relay/PLC 24V DC 5 to 40mA None 2.4V ON: When red light emitting diode
D-A80
II 3GD EEx nA II T5 X -10CTa+60C IP67
Relay/IC circuit/PLC
AC 24V DC or less
50mA
Oilproof vinyl heavy insulation cable, 3.4, 0.2mm2, 2 cores (Brown, Blue), 0.5m
This category 3 type autoswitch can only be used in zones 2 and 22.
How to order
Note) All other specifications (dimensions, drawings, etc.) are the same as the non ATEX type.
D-A
-588
Suffix for ATEX certified CAT.3
Switch No.
73 80
Electrical Entry
Contact protection box
OUT(+) Brown(Red) to OUT() Blue(Black)
Perpendicular In-line
D-A80
Reed switch Contact protection box CD-P11 CD-P12
OUT() Brown(Red) to OUT( ) Blue(Black)
Note) qIn the case operation load is an inductive load. wIn the case the wiring length to load is > 5m. Be sure to use the auto switch with the contact protection box in any case mentioned above.
38
D-A54/D-A67-588
Grommet
Specifications D-A5 (With indicator light)
Auto switch model number ATEX Category Application Load voltage Max. load current and range Contact protection circuit Internal voltage drop Indicator light 5 to 50mA Built-in 2.4V ON: When red light emitting diode PLC: Programmable Logic Controllar
D-A54
II 3GD EEx nA II T5 X -10CTa+60C IP67
Relay/PLC 24V DC
D-A67
II 3GD EEx nA II T5 X -10CTa+60C IP67
PLC/IC circuit MAX. 24V DC 30mA None 1 (Including 3m lead wire)
Note) All other specifications (dimensions, drawings, etc.) are the same as the non ATEX type.
Application Load voltage Max. load current Contact protection circuit Internal resistance
Lead wire
Oilproof vinyl heavy insulation cable, 4, 0.3mm2, 2 cores (Brown, Blue), 0.5m or 4, 0.2mm2, 3 cores (Brown, Black, Blue), 0.5m
This category 3 type autoswitch can only be used in zones 2 and 22.
How to order
D-A
Internal Circuit ( ): If not applicable for IEC Standard
D-A54
OUT() to Blue(Black)
-588
Suffix for ATEX certified CAT.3
Switch No.
54 67 With indicator lamp Without indicator lamp
39
D-A90/D-A93-588
Grommet
Specifications D-A90 (Without indicator light)
Auto swich modle number ATEX Category Application Load voltage Max. load current Contact protection circuit Internal resistance 24V
AC DC
D-A90
II 3GD EEx nA II T5 X -10CTa+60C IP67
IC circuit/Relay/PLC or less None 1 or less (Including 3m lead wire) 48V
AC DC
or less
50mA
40mA
D-A93
II 3GD EEx nA II T5 X -10CTa+60C IP67
Relay/PLC 24V DC 5 to 40mA None 2.4V (up to 20mA)/ 3V (up to 40mA) ON: When red light emitting diode
Oilproof vinyl heavy insulation cable, 2.7, 0.18mm2 X 2cores (Brown, Blue)
Note) All other specifications (dimensions, drawings, etc.) are the same as the non ATEX type.
This category 3 type autoswitch can only be used in zones 2 and 22.
How to order
D-A
Internal Circuit ( ): If not applicable for IEC Standard
Reed switch
-588
Suffix for ATEX certified CAT.3 Lead wire length
No number L Z 0.5m 3m 5m (Except D-A90)
D-A90
Switch No.
93 90 With indicator lamp Without indicator lamp
D-A93
LED Reed switch Resistance Zener diode CD-P11 CD-P12 Blue(Black) OUT() Blue(Black) Brown(Red) Contact protective box OUT(+) Brown(Red) to
Electrical entry
No number V In line Perpendicular
Note) qIn the case operation load is an inductive load. wIn the case the wiring length to load is > 5m. Be sure to use the auto switch with the contact protection box in any case mentioned above.
40
D-90A/D-93A-588
Grommet Lead wire: Heavy insulation cable
Specifications D-90A (Without indicator light)
Auto switch model number ATEX Category Application Load voltage Max. load current Internal resistance
PLC: Programmable Logic Controller
D-90A
II 3GD EEx nA II T5 X -10CTa+60C IP67
Relay/IC circuit/PLC 24V AC DC 50mA 1 or less (Including 3m lead wire)
D-93A
II 3GD EEx nA II T5 X -10CTa+60C IP67
Relay/PLC 24V DC 5 to 40mA 2.4V ON: When red light emitting diode
Oilproof vinyl heavy insulation cable, 0.2mm2, 2 cores (Brown, Blue), 0.5m
This category 3 type autoswitch can only be used in zones 2 and 22.
How to order
Reed switch Contact protection box CD-P11 CD-P12
OUT() Brown(Red) to OUT( ) Blue(Black)
D-
-588
Suffix for ATEX certified CAT.3
D-93A
Brown (Red) Reed switch Contact protection box CD-P11 CD-P12 Blue (Black) OUT(+) Brown(Red) to OUT() Blue(Black)
Switch No.
93 90 With indicator lamp Without indicator lamp
Note) qIn the case operation load is an inductive load. wIn the case the wiring length to load is > 5m. Be sure to use the auto switch with the contact protection box in any case mentioned above.
41
D-Z73/D-Z80-588
Grommet
Specifications D-Z7 (With indicator light)
Auto swich model number ATEX Category Application Load voltage Max. load current and load current range Contact protection circuit Internal voltage drop Indicator light PLC: Programmable Logic Controller
D-Z73
II 3GD EEx nA II T5 X -10CTa+60C IP67
Relay/PLC 24V DC 5 to 40mA None 2.4V (up to 20mA)/ 3V (up to 30mA) ON: When red light emitting diode
D-Z80
II 3GD EEx nA II T5 X -10CTa+60C IP67
Relay/PLC/IC circuit
Note) All other specifications (dimensions, drawings, etc.) are the same as the non ATEX type.
24V AC DC or less
50mA None
48V AC DC or less
40mA
Oilproof vinyl heavy insulation cable, 3.4, 0.2mm2, 3 cores (Brown, Black, Blue), 2 cores (Brown, Blue), 0.5m
This category 3 type autoswitch can only be used in zones 2 and 22.
How to order
D-Z
-588
Suffix for ATEX certified CAT.3
Switch No.
73 80 With indicator lamp Without indicator lamp
D-Z80
Reed switch Contact protection box CD-P11 CD-P12
OUT() Brown(Red) to OUT( ) Blue(Black)
Note) qIn the case operation load is an inductive load. wIn the case the wiring length to > 5m. Be sure to use the auto switch with the contact protection box in any case mentioned above.
42
D-E73A/D-E80A-588
Grommet
Specifications D-E73A (With indicator light)
Auto swich model number ATEX Category Application Load voltage Max. load current and load current range Contact protection circuit Internal voltage drop Indicator light PLC: Programmable Logic Controller
D-E73A
II 3GD EEx nA II T5 X -10CTa+60C IP67
Relay/PLC 24V DC 5 to 40mA None 2.4V ON: When red light emitting diode
D-E80A
II 3GD EEx nA II T5 X -10CTa+60C IP67
Relay/PLC/IC circuit
24V AC DC or less
50mA None
48V AC DC
40mA
Note) All other specifications (dimensions, drawings, etc.) are the same as the non ATEX type.
Oilproof vinyl heavy insulation cable, 3.4, 0.2mm2, 3 cores (Brown, Black, Blue), 2 cores (Brown, Blue), 0.5m
This category 3 type autoswitch can only be used in zones 2 and 22.
How to order
D-E
-588
Suffix for ATEX certified CAT.3
D-E80A
Reed switch Contact protection box CD-P11 CD-P12
OUT() Brown(Red) to OUT( ) Blue(Black)
Switch No.
73 80 With indicator lamp Without indicator lamp
Note) qIn the case operation load is an inductive load. wIn the case the wiring length to load is > 5m. Be sure to use the auto switch with the contact protection box in any case mentioned above.
43
D-H7A2-588
Grommet
Specifications D-H7 (With indicator light)
Auto switch model number ATEX Category Wiring Output Application Power voltage Current consumption Load voltage Load current Internal voltage drop 80mA or less 0.8V or less 100A at 24V DC ON: When red light emitting diode PLC: Programmable Logic Controller
D-H7A2
II 3GD EEx nA II T5 X -10CTa+60C IP67
3 wire PNP IC circuit/Relay/PLC 5/12/24V DC (4.5 to 28V DC) 10mA or less
Note) All other specifications (dimensions, drawings, etc.) are the same as the non ATEX type.
Oilproof vinyl heavy insulation cable, 3.4, 0.2mm2, 3 cores (Brown, Black, Blue), 2 cores (Brown, Blue), 0.5m
This category 3 type autoswitch can only be used in zones 2 and 22.
How to order
D-H7A2
Internal Circuit ( ): If not applicable for IEC Standard
D-H7A2
DC(+) Brown(Red) Switch main circuit
-588
Suffix for ATEX certified CAT.3
Switch No.
OUT Black(White)
DC() Blue(Black)
44
D-F7P-588
Grommet
Specifications D-F7P (With indicator light)
Auto switch model number ATEX Category Wiring Output Application Power voltage Current consumption Load voltage Load current Internal voltage drop Current leakage Indicator light
Lead wire
D-F7P
II 3GD EEx nA II T5 X -10CTa+60C IP67
3 wire PNP IC circuit/Relay/PLC 5/12/24V DC (4.5 to 28V DC) 10mA 80mA or less 0.8V or less 100A at 24V DC ON: When red light emitting diode
Oilproof vinyl heavy insulation cable, 3.4, 0.2mm2, 3 cores (Brown, Black, Blue), 2 cores (Brown, Blue), 0.5m
This category 3 type autoswitch can only be used in zones 2 and 22.
How to order
Note) All other specifications (dimensions, drawings, etc.) are the same as the non ATEX type.
D-F7P
Switch No.
-588
Suffix for ATEX certified CAT.3 Lead wire length
No number L Z 0.5m 3m 5m
Electrical entry
No number V Right arm Perpendicular
45
D-F5 P-588
Grommet
Specifications D-F5P
Auto switch model number ATEX Category Wiring Output Application Power voltage Current consumption Load voltage Load current Internal voltage drop Current leakage Indicator light
Lead wire
D-F5P
II 3GD EEx nA II T5 X -10CTa+60C IP67
3 wire PNP IC circuit/Relay/PLC 5/12/24V DC (4.5 to 28V DC) 10mA 80mA 0.8V or less 100A at 24V DC ON: When red light emitting diode
Note) All other specifications (dimensions, drawings, etc.) are the same as the non ATEX type.
Oilproof vinyl heavy insulation cable, 4, 0.3mm2, 3 cores (Brown, Black, Blue), 2 cores (Brown, Blue), 0.5m
This category 3 type autoswitch can only be used in zones 2 and 22.
How to order
D-F5P
-588
Suffix for ATEX certified CAT.3
Switch No.
46
D-Y7P(V)-588
Specifications
PLC: Programmable Logic Controller
Grommet
Perpendicular
Note) All other specifications (dimensions, drawings, etc.) are the same as the non ATEX type.
Indicator light
Lead wire
Oilproof vinyl heavy insulation cable, 3.4, 0.15mm2, 3 cores (Brown, Black, Blue), 2 cores (Brown, Blue), 0.5m
This category 3 type autoswitch can only be used in zones 2 and 22.
How to order
D-Y7P
Switch No.
-588
Suffix for ATEX certified CAT.3 Lead wire length
No number L Z 0.5m 3m 5m
Electrical entry
OUT Black(White) DC() Blue(Black)
No number V
47
Pneumatic-Pneumatic Positioner
Series Series
How to Order
56 - IP5 000
ATEX category 3 Positioner type
000 100 Lever type Rotary type
0 1 0
Accessories Note 1)
Nil A B C D E F Without accesory (standard) With 0.7 output restrictor integrated pilot valve With 1.0 output restrictor integrated pilot valve With fork lever type fitting M With fork lever type fitting S With lever unit for a 35 to 100 mm stroke With lever unit for a 50 to 140 mm stroke
With standard lever (10 to 85 mm stroke) for 56-IP5000 Common to 56-IP5000 and 56-IP5100 small capacity actuators
Imput pressure
0 1 2 Standard 0.02 to 0.1MPa 1/2 split, 0.02 to 0.06, 0.06 to 0.1MPa Low pressure, 0.04 to 0.2MPa
Note 1) If multiple accessories are required, they should be indicated in alphabetical order. Note 2) For ''E'' and ''F'', standard lever is not provided.
Ambient temperature
Nil Standard 20 to 80oC; T5 T High temperature 5 to 100oC; T4 L Low temperature 30 to 60oC; T6
Specifications
Classification II 3GD c T4 II 3GD c T5 II 3GD c T6 -30C Ta 60C
Ambient temperature range Low temp. model Standard model Low temp. model 56-IP500-L- 56-IP500-- 56-IP500-T- -5C Ta 100C -20C Ta 80C -20C Ta 60C -5C Ta 80C -5C Ta 60C 56-IP5100
Type
56-IP5000
Rotary type cam Lever type lever Item Double action Single action Double action Single action 0.14~0.7MPa Supply pressure Input pressure 0.02~0.1MPa Standard stroke 60~100 10~85mm Sensitivity Within 0.1%F.S. Within 0.5%F.S. Linearity Within 1%F.S. Within 2%F.S. Hysteresis Within 0.75%F.S. Within 1%F.S. Repeatability Within 0.5%F.S. Output flow rate 80l/min (ANR) or more (SUP.=0.14MPa) 200l/min (ANR) or more (SUP.=0.4MPa) Within 5l/min (ANR) or more (SUP.=0.14MPa) Air compsumption Within 11l/min (ANR) or more (SUP.=0.4MPa) Ambient and using fluid -20C~80C (Standard model) -30C~60C (Low Temp.) -5C~100C (High Temp.) Temperature Within 0.1%F.S./C Thermal coefficient Rc1/4 (Standard) Air connection port Aluminium diecast, Stainless steel, Brass, Nitrile rubber Material Approx. 1.2kg Approx. 1.4kg Mass 118 x 92 x 77.5 (Body) 118 x 102 x 86 (Body) Size
Note) Standard air temperature: 20, Absolute pressure: 101.3KPa. Relative humidity: 65%
48
Electro-Pneumatic Positioner
Series Series
How to Order
IP6 000
0 1 0
X14
ATEX category 2 Accessories Note 1)
Positioner type
000 100 Lever type Rotary type
Nil A B C D E F G
Without accesory With standard lever (10 to 85 mm stroke) for IP6000 (standard) With 0.7 output restrictor Common to IP6000 integrated pilot valve and IP6100 small With 1.0 output restrictor capacity actuators integrated pilot valve With fork lever type fitting MX Only for IP6100 With fork lever type fitting SX With lever unit for a 35 to 100 mm stroke Only for IP6000 With lever unit for a 50 to 140 mm stroke With compensation Common to IP6000 spring (A) and IP6100
Note 1) If multiple accessories are required, they should be indicated in alphabetical order.
Specifications
Type Item Input current Input resistance Supply air pressure Standard stroke IP6000 IP6100 Rotary type cam Levery type lever Double action Single action Double action Single action 4~20mADC (Standard) Note1 235 15 (4~20mADC) 0.14~0.7Mpa 10~85mm (External lever allowable 60~100 Note2 runout angle 10~30
Sensitivity Within 0.5%F.S. Within 0.1%F.S. Linearity Within 2%F.S. Within 1%F.S. Within 1%F.S. Within 0.75%F.S. Hysteresis Repeatability Within 0.5%F.S. Within 0.1%F.S./C Thermal coefficient 80l/min (ANR) or more (SUP.=0.14MPa) Note3 Output flow rate Within 5l/min (ANR) (SUP.=0.4MPa) Air consumption -20C~80C (T5) Ambient and using fluid -20C~60C (T6) Temperature Explosion protected Intrinsic safety type of explosion protection Construction ( II 2G Eexib II CT5/T6) 0344 Air connection port Electric wiring connection port Material Mass Classification of degree of protection Parameters (Current circuit) Approval No. KEMA No.03 ATEX1119 1/4NPT female screw M20 x 1.5 Aluminium diecast for the body Approx. 2.4kg JISF8007 IP55 (Conform to IEC pub.529) Ui 28V, Ii 125mA, Pi 1.2W, Ci OnF, Li OmH
Note 1) 1/2 split range is possible with the standard type (by adjusting the span). Note 2) The stroke is adjustable in 0~60 and 0~100. Note 3) Standard air (JIS B0120): temp. 20C, absolute press. 760mmHg, ratio humidity 65%.
49
Series IP6000
Dimensions / IP6000
/ 6100
40 35
110
M A
SPAN
65
Zero adjusting knob Span adjusting knob Two gauge ports are Rc1/8 thread 38 11 OUT1.1/4NPT SUP.1/4NPT 15 168 15
OUT2
20** MADE IN JAPAN INPUT 0/4 to 20mADC UI28V II125mA P1.2V CI0nf LI0nH EExIb CT6 Ta60C EExIb CT5 Ta80C SMC Corporation KEMA No.03ATEX1119 1-16-4 Shinbashi Minatoku Tokyo 105-8659 Japan
35
35
130 100
122
6.1 16
42 20
VIEW OF B
MODEL IP6000
125
E
} }
53
125 =180
50
NP
50
14
30
110
46
Series IP6000
/ 6100
Dimensions / IP6100
(OUT2.1/4NPT) Pluged
OUT2 M A
40 35
110
70(46) 63(39)
65
E
SPAN
Zero adjusting knob Two gauge ports are Rc1/8 thread 168
MODEL NO. IP6*00-0*0-*-X14-* SUPPLY 0.14 to 0.7MPa(1.4 to 7bar)
OUT1.1/4NPT 38 11
SMC ELECTRO-PNEUMATIC POSITIONER
Serial No.*****
SUP.1/4NPT
15 15
OUT2
SMC MPa {bar}
20** MADE IN JAPAN INPUT 0/4 to 20mADC UI28V II125mA P1.2V CI0nf LI0nH EExIb CT6 Ta60C EExIb CT5 Ta80C SMC Corporation KEMA No.03ATEX1119 1-16-4 Shinbashi Minatoku Tokyo 105-8659 Japan
35
130 100
35
42
VIEW OF B
122
20
22.5
90o
50
DA
E P
60o 30o
MODEL IP6100
Oo
30o
53
NP
44
116
60o
90o
M20x1.5 Porting for electrical connection Mark ''M'' means that this port is ''M'' thread
125 =180
51
Electro-Pneumatic Positioner
Vibration resistance : No resonances
5 to 200Hz
Conforms to
A centralised exhaust system employs the combination of the check valve and the labyrinth effect enhancing both dust resistance and water resistance performance.
Series IP8000/8100
(Lever type) (Rotary type)
100mm in height
(shortened y (shortened by by y 13% 13% compared compared with with IP6100) IP6100)
100mm
Spring pin
A span adjuster achieves 1/2 split range Mounting dimensions are same as convention types, series IP6000/6100.
52
Electro-Pneumatic Positioner
Series Series
IP8 000
Positioner type
000 100 Lever type Rotary type
How to Order
0 0 0
X14
ATEX category 2 Accessories Note 1)
Nil A B Without accesory (standard) With 0.7 output restrictor integrated pilot valve With 1.0 output restrictor integrated pilot valve With fork lever type fitting MX With fork lever type fitting SX With lever unit for a 35 to 100 mm stroke With lever unit for a 50 to 140 mm stroke With compensation spring (A) With external scale plate
With standard lever (10 to 85 mm stroke) for IP8000 Common to IP8000 and IP8100 small capacity actuators Only for IP8100
C D E F G H
Note 1) If multiple accessories are required, they should be indicated in alphabetical order.
Specifications
Type Item Input current Input resistance Supply air pressure Standard stroke Sensitivity Linearity Hysteresis Repeatability Coefficient of temperature Output flow rate Air consumption Ambient and using fluid temperature Explosion protected construction Air connection port Electrical wiring connection Material Weight Classification of degree of protection Parameters IP8000
Lever type lever feedback
IP8100
Rotary type cam feedback
Single action Double action Single action Double action 4 to 20mADC (standard) Note 1) 23515 (4 to 20mADC) 0.14 to 0.7MPa 10 to 85mm (Deflection angle 10 to 30) Within 0.1%F.S. Within 1%F.S. Within 0.75%F.S. 60 to 100 Note 2) Within 0.5%F.S. Within 2%F.S. Within 1%F.S. Within 0.5%F.S. Within 0.1%F.S. / C 80l/min (ANR) or more (SUP = 0.14MPa) Note 3) Within 5l/min (ANR) or less (SUP = 0.14MPa) 20 to 80C (T5) 20 to 60C (T6) Intrinsic safety type of explosion protection ( 0344 2G EEx ib c T5/T6) Approval no. KEMA 03 ATEX1119 1/4 NPT female screw M20x1.5 Aluminum diecast body Approx. 2.4kg JISF8007, IP65 (conforms to IEC Pub.529) Ui 28 V, li 125 mA, Pi 1.2W, Ci 0nF, Li 0mH
Note 1) 1/2 Split range is possible with the standard type (by adjusting the span). Note 2) The stroke is adjustable in 0 to 60C and 0 to 100 Note 3) Standard air (JIS B0120): temp. 20C, absolute press. 760mmHg, ratio humidity 65%.
53
Series IP8000
Accessory / Option
/ 8100
External feedback lever (IP8000 type)
Different feedback levers are available dependent upon valve strokes. Consult with SMC in case of 10mm or less stroke. Unit number P368010-20 P368010-21 P368010-22 Size M Size N 125 110 110 150 195 275
M N
6 to 12
M6 x 1
M20 x 1.5
Exploded View
Body cover unit (3) Cover seal
E L E C T O R O
P N E U M A T IC
IP 8 0 0 0
Feedback spring Mini-terminal unit (No terminal box) Span adjusting unit
SP AN
SU P
Body unit
Replacement Parts
No. 1
(2) Base seal
Note IP8000/8100
2 3
54
Series IP8000
/ 8100
Dimensions / IP8000
(OUT2.1/4NPT) Pluged
SMC MPa {bar}
M A
122 65
22.5
SPAN
198
MODEL NO. IP8*00-0*0-*-X14-* SUPPLY 0.14 to 0.7MPa(1.4 to 7bar)
20** MADE IN JAPAN INPUT 0/4 to 20mADC UI28V II125mA P1.2V CI0nF LI0nH EExIb CT6 Ta60C EExIb CT5 Ta80C SMC Corporation KEMA No.03ATEX1119 1-16-4 Shinbashi Minatoku Tokyo 105-8659 Japan
39
39
VIEW OF B 42
147 117
A
1
50
20
6.1 16 125
35
NP
14
2 30 46
100
M20 x 1.5 Porting for electrical connection Mark ''M'' means that this port is ''M'' thread
125 =199
150
accessory "E":195 { At At accessory "F":275 }
55
Series IP8000
Dimensions / IP8100
/ 8100
M A
20** MADE IN JAPAN INPUT 0/4 to 20mADC UI28V II125mA P1.2V CI0nf LI0nH EExIb CT6 Ta60C EExIb CT5 Ta80C SMC Corporation KEMA No.03ATEX1119 1-16-4 Shinbashi Minatoku Tokyo 105-8659 Japan
E
SPAN
VIEW OF B
2 x Rc1/8 23.5 43
40 35
39
147 117
39
A
ELECTORO PNEUMATIC IP8100
1
122 65 50 20
35
Positioner body
125 =199 Mark ''M'' means that this port is ''M'' thread
VIEW OF A
Mark ''M'' means that this port is ''M'' thread Hold spring
7
70(46) 63(39)
24
View of CC side Lever and pin assembly Fork and shaft assembly
NP
21
Screw thread size M6x1 Main shaft of actuator Dimension of optional ''Fork lever assembly'' ( ) Shows dimension of fork lever assembly type ''SX''
56
15
44 46
100
57
Series
56-PA3000/5000
II 3 GD c T6 Ta 0C to 60C
For more details, other specifications, dimensions, see the specific catalogue.
Automatically operated type (internal switching type) Air operated type (external switching type)
How to Order
56
ATEX category 3 PA5000
3 5
PA 3 1 1 0
Body size
3/8 standard 1/2 standard
03
Option
Nil N
Body only With silencer
For AIR EXH: AN200-02
Diaphragm material
Symbol
AIR SUP FLUID OUT
1 2
PTFE NBR
Thread type
Nil T F N
Rc NPTF G NPT
AIR EXH
FLUID IN
56
PA5000 ATEX category 3
3 5
PA 3 1 1 3
Body size
3/8 standard 1/2 standard
03
Connection port size
03 04 06
3/8 (10A): PA3 1/2 (15A): PA5 3/4 (20A): PA5
Thread type
Nil T F N
Rc NPTF G NPT
Symbol
Diaphragm material
P1 P2 FLUID OUT
PTFE
58
Booster Regulator
How to Order
VBA1000
56
ATEX category 3
VBA 1 1 1 0
Body size
1 1/4
02 GN
Option
G Pressure Gauge (MPa) Silencer N The option is delivered in the same packing but it is not mounted.
Pressure setting
1 Handle operated
Port size
Symbol 02 Port size 1/4
VBA1110-02 1 VBA1111-02
Pressure class
2.0MPa
Nil T F N
Rc NPTF G NPT
VBA2000/4000
56 VBA 2 1 0 0
ATEX category 3 Body size
2 4 3/8 1/2
03 GN
Option
Gauge G Silencer N The option is delivered in the same packing but it is not mounted.
Pressure setting
1 2 Handle operated Air operated
Port size
VBA4100-04 Handle operated style VBA2100-03
Pressure class
0 1.0MPa
Symbol
03 04
Thread type
Nil T F N
Rc NPTF G NPT
VBA2200-03
59
Series
52 - SY 5 1 2 0
ATEX category 2 Series
5 7 9 52-SY5000 52-SY7000 52-SY9000
52-SY
II 2G EEx ia IIB T4...T6
For more details, other specifications, dimensions, see the specific catalogue
How to Order
L 3
01 F
Bracket
Nil No bracket F1 With foot bracket* F2 With side bracket** *Foot bracket only available for 2 position single solenoid valve 52-SY5000 and 52-SY7000. **Side bracket only for 52-SY5000 and 52-SY7000. ***No bracket for only body ported type's 52-SY9000.
Type of actuation
1 2 3 4 5 2-position single 2-position double 3-position closed centre 3-position exhaust centre 3-position pressure centre
Thread style
Nil F N T Rc G NPT NPTF
Piping style
2 4 Body ported type Base mounted type Sign 01 C4 C6 C8 N3 N7 N9 02 C8 C10 N9 N11 02 03 C8 C10 C12 N9 N11 Sign 02 02 03 03 04
Internal pilot Nil External pilot* R *Only the base mounted type.
52-SY5000
Barrier
Nil A B C D E Without barrier Z728.H MTL728P+ MTL7128P+ MTL5021 KFD2-SD-Ex1.17
52-SY7000
52-SY9000
Electrical entry
Plug connector type L LL Plug connector with cover type Terminal type TT
Port size (Base mounted type) Port size Compatible series No sub-plate 52-SY5000 1/4 1/4 52-SY7000 3/8 3/8 52-SY9000 1/2
Manual override
Non locking push style Nil D Push-turn locking slotted style E Push-turn locking lever style
60
Series 52-SY
For more details, other specifications, dimensions, see the specific catalogue
Specifications
Series Ambient and fluid Temperature class T6 Temperature class T4, T5 temperature Coil temperature rise Barrier input voltage (non hazardous area) Solenoid valve input voltage (hazardous area) Intrinsically safe Gas group L type plug connector Electrical entry T type terminal box 52-SY5000 52-SY7000 52-SY9000
45C 50C 40C or less (at rated) 24VDC (system rated voltage) at 1.1W 12VDC at 0.52W ia IIB IP30 (LL type : IP40) IP65
Safety Instructions
1) This product is not suitable for Zone 0. The suitable zones are Zones 1 and 2. 2) SMC-TAS and TAU Series, antistatic tubing, is available if required. 3) the solenoid valve has polarity (+ -). Confirm the correct polarity by referring to the colour of the lead wires. If the polarity is reversed, the barrier maybe damaged. 4) Confirm that the solenoid input voltage at the lead wires is DC 10.8V (min). 5) The product must be connected to a certified barrier or certified intrinsically safe circuit with the follow maximum Values: Ui= 28V li= 225mA (resistively limited) Pi= 1W Ci= 0.nF Li= 0 nH Note) The valve is not supplied with barrier.
Note1) Impact resistance: No malfunction resulted from the impact test using a drop impact tester. The test were performed one time each in the axial and right angle directions of the main valve and armature, in both energised and de-energised states (Valve in the initial stage). Vibration resistance: No malfunction ocurred in a one-sweep test between 8.3 and 2000Hz. The test was performed for both energised and de-energised states in the axial and right angle directions of the main valve and armature (valve in the initial stage).
Response time
Configuration 2-position single 2-position double 3-position Response time (ms) (0.5MPa) 52-SY5000 52-SY7000 52-SY9000 26 or less 38 or less 50 or less 22 or less 30 or less 50 or less 38 or less 56 or less 70 or less
Note1) According to dynamic performance test JIS B8375-1981. Note2) Response time when barriers were combined with a valve. System A: Valve + Z728.H (Pepperl + Fuchs) B: Valve + MTL728P+ C: Valve + MTL7128P+ E: Valve + KFD2-SD-Ex1.17 (Pepperl + Fuchs) Note3) When system D is used, the ON time is delayed 17ms more than response time in table. System D: Valve + MTL5021
Single base/ B mounting Common SUP/ Common EXH 2 to 20 (1) Valve 1/4
Note) Values for 5 stations manifold with a 2 position single type valve.
1/8 1/4 C4 (One-touch fittings for 4mm) C8 (One-touch fittings for 8mm) C6 (One-touch fittings for 6mm) C10 (One-touch fittings for 10mm) C8 (One-touch fittings for 8mm) W=36n+64 Manifold base weight W (g) n: Station W=43n+64
Note1) For more than 10 stations (more than 5 stations in case of SS5Y7), supply pressure to P port on both sides and exhaust from EA/EB port on both side. Note2) 52-SY9*20 valve are not available with manifold as standard. Please contact SMC if you require it: Note3) 52-SY series are not available with resin type manifold (23 type, 20P type and 45 type).
Note) Values for 5 stations manifold with a 2 position single type valve.
W=61n+101
W=79n+127
W=100n+151
Note1) For more than 10 stations (more than 5 stations in case of SS5Y7), supply pressure to P port on both sides and exhaust from EA/EB port on both side. Note2) 52-SY9*40 valve are not available with manifold as standard. Please contact SMC if you require it: Note3) 52-SY series are not available with resin type manifold (23 type, 20P type and 45 type).
61
Series 52-SY
Dimensions
Body ported type Dimensions/ Series 52-SY5000 2-position single Plug connector type (L) 52-SY5120-L-01-(-F2)
22.6
21
16.6
22 111.8
65 Insulation Black(-) A Insulation Red(+) Manual override 16.2 36 2-3.2 (Mounting holes) 44 (For E type) (37)
2-M3 Threads depth 3.5 (For bracket mounting) 14.7 11.6 40 2-3.2 (Mounting holes)
14.7
1.55
(32.3)
1.6
0.8
32.3
20.5
(36.7)
32.5
(40.2)
40
0.3mm2
15
EB
(20)
32 27.2 (45)
11
4.1
14.7
104
12
120.8
62
1.2
29
Series 52-SY
Dimensions
Body ported type Dimensions/Series 52-SY5000 2-position double Plug connector type (L) 52-SY5220-L-01-(F2)
22.6 16.7 2-M3 Threads depth 3.5 (For bracket mounting) 65.4 B Manual override A 16.2 36 37 2-3.2 (Mounting holes for manifold) 2-1/8" {4(A),2(B) Port} 2-3.2 (Mounting holes) (40.2) L (Lead wire length) 3-1/8" {1(P),5(EA),3(EB) Ports} 1.6 1.55 153.6 (76.8) 0.8 EA 2-2.2 (Positioning for manifold gasket) P EB 27.2 (45) (88.5) 15 (20) 143.4 14.7 (71.7) 177 12 20.5 32.5 (36.7) 0.3mm 2 44 (For E type) 40 11.6
(1.2) (11.7)
0.3mm2
0.75mm2
14.7
63
Series 52-SY
Dimensions
Body ported type Dimensions/Series 52-SY5000 3-position closed centre-exhaust centrepressure centre Plug connector type (L) 3 2-M3 threads depth 3.5 52-SY5420-L-01-(F2) (For bracket mounting) 5 32.7
Insulation Black(-) A Insulation Red(+) Manual override
22.6 16.7 (89.4) 45.3 11.6 B 16.2 36 (37) 2-3.2 (Mounting holes for manifold) 2-1/8" {4(A),2(B) Port} 2-3.2 (Mounting holes)
44 (For E type)
0.3mm 2 40
(40.2)
14.7
(1.2)
1.55
20.5
EB
27.2 (45)
Plug connector with cover type (LL) 3 52-SY5420-LL-01-(F2) L 5 (Lead wire length)
Insulation: Red(+) Insulation: Black(-) 4.1
156
0.3mm 2
14.7
84.3
189.6
0.75mm 2
12
101.1
64
(20)
15
32.5
(36.7)
Series 52-SY
Dimensions
Body ported type Dimensions/Series 52-SY7000 2-position single Plug connector type (L) 52-SY7120-L-02-(F2)
2-M4 threads depth 6.5 (For bracket mounting) 20 29.4 7
57 46 5.5
19.8
28 125
79.2 Insulation Black(-) Insulation Red(+) (14) 1.2 Manual override 13.6 B A 20 42 (52) 40 14.7
2-4.2 (Mounting holes for manifold) 2-1/4" {4(A),2(B) Port} 2-4.2 (Mounting holes)
14.7
(39.4) L (Lead wire length) 123.3 0.9 39.4 2 1/4" {1(P) Port} 2-1/8" {5(EA),3(EB) Ports} EA 2-2.2 (Positioning for manifold gasket) 36 (66) P
24.5
(42.5)
0.3mm 2 40
44 (For E type)
40
(49.5)
EB
(23.9)
18
39.5
13
14.7
118.2
12
0.75mm 2
135 Max.10
1.2
38
65
Series 52-SY
Dimensions
Body ported type Dimensions/Series 52-SY7000 2-position double Plug connector type (L) 52-SY7220-L-02-(-F2)
20
79.6 Insulation Black(-) Insulation Red(+) B 13.6 Manual override A 20 42 (52) 2-4.2 (Mounting holes) 44 (For E type) 2-4.2 (Mounting holes for manifold) 2-1/4" {4(A),2(B) Port} 0.3mm 2 40 14.7
(49.5)
(1.2) (14)
1.55
EA 36 (66)
EB
18
24.5
0.3mm 2 (78.8)
0.75mm 2 (95.6)
66
4.1
(23.9)
(42.5)
40
Series 52-SY
Dimensions
Body ported type Dimensions/Series 52-SY7000 3-position closed centre-exhaust centrepressure centre Plug connector type (L) 3 52-SY7420-L-02-(-F2) 5
Insulation Black(-) Insulation Red(+)
20
39.8
52.8 B 13.6
Manual override
A 20 42 (52)
2-4.2 (Mounting holes for manifold) 2-1/4" {4(A),2(B) Port} 2-4.2 (Mounting holes)
(49.5)
14.7
(1.2) (14)
1.55
Plug connector with cover type (LL) 3 52-SY7420-LL-02-(-F2) L 5 (Lead wire length)
4.1 Insulation: Red(+) Insulation: Black(-)
170.6
0.3mm 2
204.2
0.75mm 2
24.5
(42.5)
0.3mm 2 40
44 (For E type)
40
67
Series 52-SY
Dimensions
Insulation Red(+)
Manual override 33.6 64.2 3-3.2 (Mounting holes of manifold) 2-1/4",3/8" {4(A),2(B) Port}
46 (For E type)
0.3mm2 42
18.4
Body ported type Dimensions/Series 52-SY9000 2-position single Insulation Plug connector type (L) Black(-) 02 52-SY9120-L-03
16.7
1.55
24.9
43.85
5EA 49.8
1P
3EB 0.5
4.1
14.7
148.3
68
23
0.5
56.3
10
36.6
51.5
Series 52-SY
Dimensions
Body ported type Dimensions/Series 52-SY9000 2-position double Insulation Plug connector type (L) Black(-) 52-SY9220-L-02 03
Insulation Red(+) Manual override
106 18.4 2B 33.6 64.2 3-3.2 (Mounting holes for manifold) 2-1/4",3/8" {4(A),2(B) Port} 24.9 194.2 10 36.6 97.1 0.5 1P 49.8 3EB 0.5 23 5EA 51.5 6.5 4A
16.7
1.55
4.1
14.7
0.3mm2 42
69
Series 52-SY
Dimensions
Body ported type Dimensions/Series 52-SY9000 2-position closed centre - exhaust centre Insulation pressure centre Black(-) Plug connector type (L) 3 02 Manual override 52-SY9420-L-03 Insulation Red(+) 5
123 6.5 4A 2B 18.4 33.6 64.2 3-3.2 (Mounting holes for manifold) 2-1/4",3/8" {4(A),2(B) Port} 24.9 210.7 10 5EA 49.8 1P 3EB 0.5 (108.5) 201 (125.3) 234.1 23 0.5 36.6 51.5 113.6
16.7
1.55
70
14.7
46 (For E type)
0.3mm2 42
Series 52-SY
Dimensions
Base mounted type Dimensions/Series 52-SY5000 2-position single Plug connector type (L) 52-SY5140(R)-L-02
A A
B 35 B P 56 65 EB 4.3 62.5
9.5
18
19
PE
17 M5 (Pilot EXH. port) <For external pilot type>
Insulation Red(+)
EA
X 17
1.55
18
18 28
4.1
Max.10 120.8
5.9
12
0.75mm2
14.7
0.3mm 2
9.5
22
71
Series 52-SY
Dimensions
Base mounted type Dimensions/Series 52-SY5000 2-position double Plug connector type (L) 52-SY5240(R)-L-02
37.2 15.5 17.5 Insulation Black(-) 2-4.3 (Mounting holes) Manual override A A EA
18
19 9.5
48 B B EB
4 4
PE
17 M5 (Pilot EXH. port) <For external pilot type>
Insulation Red(+)
P 56 65.4 153.6
0.3mm 2
1.55
18
18 28
4.1
0.3mm2
72
5.9
0.75mm 2
12
14.7
22
35
Series 52-SY
Dimensions
Base mounted type Dimensions/Series 52-SY5000 3-position closed centre - exhaust centre pressure centre Plug connector type (L) 3 52-SY5440(R)-L-02 5
37.2 15.5 17.5 Insulation Black(-) 2-4.3 (Mounting holes) Manual override A A EA
18
19 9.5
48 B B EB
4 4
Insulation Red(+)
P 56
1.55
0.3mm2
18 28
156
4.1
0.3mm2
14.7
84.3
Max.10 189.6
5.9
0.75mm 2
12
9.5
89.4
101.1
22
35 44.1
PE
73
Series 52-SY
Dimensions
Base mounted type Dimensions/Series 52-SY7000 2-position single Plug connector type (L) 52-SY7140(R)-L-02
21
22.5 13.5
79.2 41.9 21.5 Manual override 23 Insulation Black(-) 61 2-4.3 (Mounting holes) A A B Insulation Red(+) 21 123.3 M5 (Pilot EXH. port) <For external pilot type> L (Lead wire length) 0.3mm 2 1.55 EA P 69 EB 6.4 67.2 21 B 38 46 10.4 21 4 M5 (External pilot port)
PE
11.5
20.5
20.5 33
4.1
0.3mm 2
74
5.9
12
0.75mm 2
14.7
13.5
26.5
Series 52-SY
Dimensions
Base mounted type Dimensions/Series 52-SY7000 2-position double Plug connector type (L) 52-SY7240(R)-L-02
61
4 2-4.3 (Mounting holes) M5 (External pilot port) 46 23 38 EB 21.5 67.2 (78.8) (95.6) 11.5 13.5 26.5 X 4 21
B B
EA
P 69 79.6 167.8
20.5 20.5 33
157.6
4.1
0.3mm 2
Max.10 191.2
0.75mm 2
5.9
14.7
13.5
21
22.5
PE
75
Series 52-SY
Dimensions
Base mounted type Dimensions/Series 52-SY7000 3-position closed centre - exhaust centre pressure centre Plug connector type (L) 3 52-SY7440(R)-L-02 5
41.9 21.5 Insulation Black(-) Manual override 23 A A
61
4 2-4.3 (Mounting holes) M5 (External pilot port) 46 23 38 EB 21.5 44.1 67.2 96.9 91.8 11.5 13.5 108.6 26.5 X 4 21
B B
Insulation Red(+) 21 M5 (Pilot EXH. port) <For external pilot type> L (Lead wire length) 0.3mm 2 1.55 71.2 (For E type)
EA
P 69 92.6 180.8
20.5 20.5 33
170.6
4.1
0.3mm2
14.7
Max.10 204.2
0.75mm 2
76
5.9
13.5
21
22.5
PE
Series 52-SY
Dimensions
Base mounted type Dimensions/Series 52-SY9000 2-position single Plug connector type (L) 02 52-SY9140(R)-L-03
29
30 17.5
109.3 51.2 25 Manual override 28.5 Insulation Black(-) 86.5 2-5.4 (Mounting holes) A4 B2 47 B 1P 96.5 153.4 3EB 11.8 76.5 25 57 16.8 1/8" (External pilot port) 27
PE
A
Insulation Red(+) 27 1/8" (Pilot EXH. port) <For external pilot type> L (Lead wire length) 0.3mm 2 1.55 80.5 (For E type) 5EA
29.5 44.5
4.1
0.3mm 2
Max.10 165.1
5.9
0.75mm 2
12
14.7
15.5
17.5
34
77
Series 52-SY
Dimensions
Base mounted type Dimensions/Series 52-SY9000 2-position double Plug connector type (L) 02 52-SY9240(R)-L-03
29
30 17.5
106 51.2 25 Manual override 28.5 Insulation Black(-) 86.5 2-5.4 (Mounting holes) 4A 2B B 1P 96.5 194.2 76.5 3EB 25 47 57 5
27
PE
A
Insulation Red(+) 27 1/8" (Pilot EXH. port) <For external pilot type> L (Lead wire length) 0.3mm 2 1.55 80.5 (For E type) 5EA
29.5 44.5
184
4.1
0.3mm 2
14.7
5.9
0.75mm2
12
78
15.5
(92)
(108.8)
17.5
34
Series 52-SY
Dimensions
Base mounted type Dimensions/Series 52-SY9000 3-position closed centre exhaust centre - Pressure centre Plug connector type (L) 3 02 52-SY9440(R)-L-03 5
51.2 25 Manual override 28.5 Insulation Black(-)
29
30 17.5
123 86.5 2-5.4 (Mounting holes) A4 B2 47 B 1P 96.5 210.7 3EB 69.1 76.5 25 57 1/8" (External pilot port) 27
PE
A
Insulation Red(+) 27 1/8" (Pilot EXH. port) <For external pilot type> 5EA
0.3mm 2
1.55
29.5 44.5
113.6
Plug connector with cover type (LL) 3 02 52-SY9440(R)-LL-03 L (Lead wire length) 5
Insulation: Red(+) Insulation: Black(-)
200
4.1
0.3mm 2
14.7
15.5
17.5
5.9
12
34 108 125.3
79
Series 56-SV
(+COM, -COM common)
II 3GD EEx nA II T5X T90 IP67
For more details, other specifications, dimensions, see the specific catalogue
How to Order
56 - SV 1 1 0 0
ATEX category 3 Series
1 2 3 4 56-SV1000 56-SV2000 56-SV3000 56-SV4000
5 F Z
Manual override
Nil D Non lock/ Push type Push turn lock type Driver operation type
Configuration
2-position single solenoid 1 2-position double solenoid 2 3-position closed centre 3 3-position exhaust centre 4 3-position pressure centre 5 4-position dual 3 port valve: N.C./N.C. A 4-position dual 3 port valve: N.O./N.O. B 4-position dual 3 port valve: N.C./N.O. C * 4-position dual 3 port valve is only available in 56-SV1000 and 2000 series.
Rated voltage
24VDC 5 12VDC 6 * Only 24VDC is applicable to the 56-EX500 series.
Not built-in Nil Built-in K Pilot * Backpressure check valve type is only Internal pilot Nil available in the 56-SV1000 series External pilot R * Backpressure check valve is not incorporated * External pilot specification is not in the 3-position closed centre and 3-position available in 4-position dual 3-port valve. pressure center configurations.
SV 1 000
Series
1 2 3 4 56-SV1000 56-SV2000 56-SV3000 56-SV4000
67
1A
80
Series
56-SV
II 3GD EEx nA II T5X T90C IP67
For more details, other specifications, dimensions, see the specific catalogue
How to Order
Applicable to Serial 56-EX500> Manifold numbering system (Base piping type/ Tie rod base)
56 - SS5V 1 W 10 N S A2W D 06 U R
ATEX category 3 Series
1 2 3 4 56-SV1000 56-SV2000 56-SV3000 56-SV4000
C6
Position of P, E port
U D B U side (4 to 10 stations) D side (4 to 10 stations) Both sides (4 to 10 stations)
IP67 specification
SI unit
Applicable to Profibus A2W For gateway (+COM) Applicable to Profibus A2WN For gateway (-COM) * Common specification for manifold and SI unit should be identical.
Manifold station
04 06 08 04 06 08 10 4 stations 6 stations 8 stations 4 stations 6 stations 8 stations 10 stations Double wiring
Note1)
Only the manifold stations above are available. When a valve number does not correspond to a manifold station, use a blanking plate to match both numbers. Note1) Double wiring specification: single, double, 3-position, and 4-position solenoid valve can be used for all manifold station. When using a single solenoid, some control signals will not be counted. Therefore, specify the signal layout at the time an order is placed. Note2) Layout specification: Please use the Manifold Specification Sheet to provide wiring. (The double solenoid valve and 3-position or 4-position solenoid valve are not available when single wiring is specified. Please note this.)
A & B port 1/8" One-touch fitting 5/32" One-touch fitting 1/4" One-touch fitting 5/32" One-touch fitting 1/4" One-touch fitting 5/16" One-touch fitting 1/4" One-touch fitting 5/16" One-touch fitting 3/8" One-touch fitting 5/16" One-touch fitting 3/8" One-touch fitting NPT 1/4 NPT 3/8 NPTF 1/4 NPTF 3/8 Mixture of A and B ports
P & E port
Series
5/16" One-touch 56-SV1000 fitting series 3/8" One-touch fitting 3/8" One-touch fitting 3/8" One-touch fitting NPT 3/8 NPTF 3/8 56-SV4000 series 56-SV2000 series 56-SV3000 series
Note 1: Please complete the Manifold Specification Sheet when specifying the mixture specification (M). Note2: For the external pilot specification (R), the X and PE port size are as follows: - 4mm or 5/32" for the 56-SV1000 and 56-SV2000 series - 6mm or 1/4" for the 56-SV3000 and 56-SV4000 series
81
Series
56-SV
II 3GD EEx nA II T5X T90 IP67
For more details, other specifications, dimensions, see the specific catalogue
How to Order
Applicable to multi-connector> Manifold numbering system (Base piping type/ Tie rod base)
56 - SS5V 1 W 10 N C D 06 U R
ATEX category 3 Series
1 2 3 4 56-SV1000 56-SV2000 56-SV3000 56-SV4000
C6
Position of P, E port
U D B U side (4 to 10 stations) D side (4 to 10 stations) Both sides (4 to 10 stations)
Voltage specification
Nil 12V 24VDC 12VDC
IP67 specification
* Please pay attention to the polarity because a diode for protecting against miswiring is not incorporated in the 12VDC version.
Manifold station
04 06 08 10 04 06 08 10 4 stations 6 stations 8 stations 10 stations 4 stations 6 stations 8 stations 10 stations Double wiring
Note1)
Specified layout
Note2)
Only the manifold stations above are available. When a valve number does not correspond to a manifold station, use a blanking plate to match both numbers. Note1) Double wiring specification: single, double, 3-position, and 4-position solenoid valve can be used for all manifold station. When using a single solenoid, some control signals will not be counted. Therefore, specify the signal layout at the time an order is placed. Note2) Layout specification: Please use the Manifold Specification Sheet to provide wiring. (The double solenoid valve and 3-position or 4-position solenoid valve are not available when single wiring is specified. Please note this.)
Note 1: Please complete the Manifold Specification Sheet when specifying the mixture specification (M). Note2: For the external pilot specification (R), the X and PE port size are as follows: - 4mm or 5/32" for the 56-SV1000 and 56-SV2000 series - 6mm or 1/4" for the 56-SV3000 and 56-SV4000 series
82
Series 56-SV
Dimensions
Conform to ATEX directive Dimensions/ Series 56-SV1000 Circular Connector Tie-rod base manifold: 56-SS5V1-W10CD- Stations
U D B
(R)-
*When P,E port outlets are indicated on the U side or D side, the P,E ports on the opposite side are plugged. *External pilot port positions are the same as P,E port outlet positions.
With external pilot specification 18.3 8.6 (pitch) P=10.5 13.5 60.6 14.1 8.4
24.6 23 10
56.5 43
One-touch fitting [4(A),2(B) port] Applicable tubing O.D.:3.2,1/8" 4, 5/32" 6, 1/4" L1 L2 (C6:3.2) (N7:7) (4.9) 47.8 43.7 D side
U side
18
19
17
26
20
15
16
25
21
24
14
23
22
13
12
11
10
29.6
4.6 6.2
8.9 2.7
26.4
Manual override and turn for (Press the locking type. ) 4(A) port side:Orange 2(B) port side:Green
(Station n) (Station 1) Light/Surge voltage suppressor (Cable assembly) (Min.bending radius 20mm)
L:dimensions n:stations
6 8 10 L n 4 L1 137.3 158.3 179.3 200.3 L2 84 105 126 147
10
52.2
38.4
PE
PE
3 5
4 2
A4 B2
A4 B2
A4 B2
A B
3 5
3/5
4 2
B
A4 B2
B
A4 B2
B
A4 B2
B
A B
E P
3/5 1
83
Series 56-SV
Dimensions
Conform to ATEX directive Dimensions/ Series 56-SV1000 56-EX500 Decentralised Serial Wiring Tie-rod base manifold: 56-SS5V1-W10SAWD- Stations
*When P,E port outlets are indicated on the U side or D side, the P,E ports on the opposite side are plugged. *External pilot port positions are the same as P,E port outlet positions.
U D B
(R)-
13.5
14.1
8.4
4 A4 B2 A4 B2 A4 B2 A
56.5
43
One-touch fitting [4(A),2(B) port] Applicable tubing O.D.:3.2,1/8" 4,5/32" 6,1/4" D side L1 L2 (C6:3.2) (N7:7) 34.1 SI unit (4.9) 9.2
U side
PWR COM
9.5
4.6
Manual override Press and turn for the locking type. 4(A) port side:Orange 2(B) port side:Green (Station n) (Station 1)
Light/Surge voltage suppressor L:dimensions n:stations 67.5 59.5 45.5 58.7 65.4
6 8 10 L n 4 L1 123.6 144.6 165.6 186.6 L2 84 105 126 147
84
10
6.2
9.6
3.4
26.4
C1
2-M12 One-touch fitting [X:External pilot port] Applicable tubing O.D.:4 5/32" One-touch fitting [PE:Pilot EXH.port] Applicable tubing O.D.:4 5/32"
C1
PE
PE
C2
E P
3 5 1 2 B
3 5 1
C2
E P
3 5 1 2
B
B2
B2
B2
E P
3 5 1
Series 56-SV
Dimensions
Conform to ATEX directive Dimensions/ Series 56-SV2000 Circular Connector Tie-rod base manifold: 56-SS5V2-W10CD- Stations
U D B
(R)-
*When P,E port outlets are indicated on the U side or D side, the P,E ports on the opposite side are plugged. *External pilot port positions are the same as P,E port outlet positions.
(pitch) P=1617.5
60.7
30.6 25.2
63.5 49.9
One-touch fitting [1(P),3/5(E) port] Applicable tubing O.D.:10 3/8" U side 4-5.3 (For mounting) Earth terminal (M4) L1 L2 (4.9)
One-touch fitting [4(A),2(B) port] Applicable tubing O.D.:4,5/32" 6,1/4" 8,5/16" D side 46.2 (5.3) 43.7
115.5 97.5
A
B
A
B
18
19
17
29.6 12.2
26
20
15
16
25
21
24
14
23
22
13
12
11
10
5.4 6.2
11.4 5.2
26.4
Manual override Press and turn for the locking type. 4(A) port side:Orange 2(B) port side:Green
54.2
L:dimensions n:stations
6 8 10 L n 4 L1 164.2 196.2 228.2 260.2 L2 112 144 176 208
12
40.8
E P
3/5 PE 1 B 2 B 2 B 2 B 2
4 A
4 A
4 A
4 E P 3/5 PE 1
E P
3/5 1 B
B
4 A 2 B
B
4 A 2 B
B
4 A 2 B
B
4 2
P P 1 1
3/5
85
Series 56-SV
Dimensions
Conform to ATEX directive Dimensions/ Series 56-SV2000 56-EX500 Decentralised Serial Wiring Tie-rod base manifold: 56-SS5V2-W10SAWD- Stations
*When P,E port outlets are indicated on the U side or D side, the P,E ports on the opposite side are plugged. *External pilot port positions are the same as P,E port outlet positions.
U D B
(R)-
46.5 11.8
20.6 44.1
63.5 49.9
One-touch fitting [1(P),3/5(E) port] Applicable tubing O.D.:10 3/8" U side 4-5.3 (For mounting) Earth terminal (M4) L1 L2
One-touch fitting [4(A),2(B) port] Applicable tubing O.D.:4,5/32" 6,1/4" 8,5/16" D side 32 9.2 SI unit (4.9) (5.3)
A
B
A
B
29.6 12.2
PWR COM
115.5 97.5
9.5
10.7
5.4 6.2
Manual override Press and turn for the locking type. 4(A) port side:Orange 2(B) port side:Green
86
12
59.6 66.3
4.5
26.4
PE
C1
PE
2-M12
C2
E P
3/5 1 B 2B 2B 2B 2
4A
4A
4A
4 P E 3/5 1
C1
C2
E P
3/5 1 B
B
4A 2B
B
4A 2B
B
4A 2B
B
4 2 P 1 E 3/5
Series 56-SV
Dimensions
Conform to ATEX directive Dimensions/ Series 56-SV3000 Circular Connector Tie-rod base manifold: 56-SS5V3-W10CD- Stations
U D B
(R)-
*When P,E port outlets are indicated on the U side or D side, the P,E ports on the opposite side are plugged. *External pilot port positions are the same as P,E port outlet positions.
With external pilot specification 23.5 11.6 (pitch) P=20.5 21.3 61.3 18 11
76.8 60.3
One-touch fitting [1(P),3/5(E) port] Applicable tubing O.D.:12 3/8" U side L1 L2 (5.3) Earth terminal (M4)
One-touch fitting [4(A),2(B) port] Applicable tubing O.D.:6 ,1/4" 8 ,5/16" 10,3/8" D side 44.3 (5.1) 43.7
A B
A
B
A
4
58.9 71.3
18
19
17
26
20
15
16
25
21
24
14
23
22
13
12
11
10
10.1 3.9
26.4
Manual override Press and turn for the locking type. 4(A) port side: Orange 2(B) port side: Green
12
39.6
E P
PE
3 5 A
X
4 A 2 B
4 A 2 B
4 A 2 B
4 E 2 P
PE
3 5
X
E P
3 5 A 1 B
B
4 A 2 B
B
4 A 2 B
B
4 A 2 B
B
4 E 2 P
3 5 1
87
Series 56-SV
Dimensions
Conform to ATEX directive Dimensions/ Series 56-SV3000 56-EX500 Decentralised Serial Wiring Tie-rod base manifold: 56-SS5V3-W10SAWD- Stations
*When P,E port outlets are indicated on the U side or D side, the P,E ports on the opposite side are plugged. *External pilot port positions are the same as P,E port outlet positions.
U D B
(R)-
With external pilot specification (pitch) P=20.5 23.5 21.3 48.6 11.8 11.6 18 11
36.1 13.5
36 37.6 59.5
76.8 60.3
One-touch fitting [1(P),3/5(E)port] Applicable tubing O.D.:12 3/8" U side L1 6.5 (5.3) Earth terminal (M4) L2
2-M12 One-touch fitting [4(A),2(B) port] Applicable tubing O.D.:6 ,1/4" 8 ,5/16" 10,3/8" D side 31.6 (5.1) 9.2
SI unit 9.5
B B B
B
A B
A
B
PWR
68.5 108.5
COM
6.2
Manual override Press and turn for the locking type. 4(A) port side: Orange 2(B) port side: Green
(Station 1)
10.1 3.9
88
12
26.4
C1
C2
E P
PE
3 5 A
X
4 A 2 B
4 A 2 B
2 B
4 A
4 E 2 P
PE
3 5
X
C1
C2
E P
3 5 A 1 B
4 A 2 B
4 A 2 B
4 A 2 B
4 E 2 P
3 5 1
Series 56-SV
Dimensions
Conform to ATEX directive Dimensions/ Series 56-SV4000 Circular Connector Tie-rod base manifold: 56-SS5V4-W10CD- Stations
U D B
02,C8,
*When P,E port outlets are indicated on the U side or D side, the P,E ports on the opposite side are plugged. *External pilot port positions are the same as P,E port outlet positions.
25
(pitch) P=24 24
35 14.5
13.7 35.8
74.8 58.3
One-touch fitting [4(A), 2(B) port] Applicable tubing O.D.:8,5/16" 10,3/8" 12 U side 4-6.2 (For mounting) Earth terminal (M4) L1 L2 (5.4)
D side
47.3
43.7
164.7 148.2
A
B
A
B
A
4
75
18
29.6 17.5
19
17
26
20
15
16
25
21
24
14
23
22
13
12
11
10
12.2 6
26.4
Manual override Press and turn for the locking type. 4(A) port side: Orange 2(B) port side: Green
6.2
16.2
58.5
41.6
PE
PE
E P
3/5
1 B
4 A 2 B
4 A 2 B
4 A 2 B
4 E 2 P
3/5 1
E P
3/5
1 B
4 A 2 B
2 B
4 A
4 A 2 B
2 P
4 E
3/5 1
89
Series 56-SV
Dimensions
Conform to ATEX directive Dimensions/ Series 56-SV4000 56-EX500 Decentralised Serial Wiring Tie-rod base manifold: 56-SS5V4-W10SAWD- Stations
*When P,E port outlets are indicated on the U side or D side, the P,E ports on the opposite side are plugged. *External pilot port positions are the same as P,E port outlet positions.
U D B
02,C8,
With external pilot specification 25 (Pitch) P=24 24 48.6 11.8 35 14.5 13.7 35.8 40.4 63.9
E 3/5 A 4 A 4 A 4 A 4 E 3/5
20 11
E
C1 C2
74.8 58.3
One-touch fitting [4(A),2(B) port] Applicable tubingO.D.: 8,5/16" 10,3/8" 12 U side L1 L2 (5.4)
2-M12 Rc3/8 [1(P),3/5(E) port] Rc1/4,3/8 [4(A),2(B) port] D side 9.2 30.1
One-touch fitting [X: External pilot port] Applicable tubing O.D.: 6 1/4"
164.7 148.2
A
B
A
B
29.6 17.5
PWR COM
9.5
6.2
Manual override and turn for (Press the locking type. ) 4(A) port side: Orange 3(B) port side: Green
6.2
SI unit
26.4
90
16.2
79.4 86.1
PE
PE
C1
3/5
1 B
4 A 2 B
4 A 2 B
4 A 2 B
4 E 2 P
3/5 1
C2
1 B
2 B
2 B
2 B
2 P
91
Series
56-VQC1000
II 3GD EEx nA II T5X T85C IP67
For more details, other specifications, dimensions, see the specific catalogue.
M F/T L S Kit
Options
None
Kit
Manifold model
1
Plug-in unit
B All stations with back pressure check valve D With DIN rail (rail length: standard) D With DIN rail (rail length: special) K N R S
Special wiring specifications (except for double wiring) With name plate External pilot Direct exhaust with built-in silencer
Stations
01
1 station
COM.
The maximum number of stations differs depending on the electrical entry (refer to Electrical entry/Cable length).
() COM.
00 EX5 series
Multiple connector kit (26P) without cable Multiple connector kit (26P) with 1.5m cable 1 to 12 stations Multiple connector kit (26P) with 3.0m cable (24 stations) TD0 Terminal block box kit Multiple connector kit (26P) with 5.0m cable
SDA2 PROFIBUS-DP
92
Series 56-VQC
Base-Mounted Type
Plug-in Unit
56 - VQC 1 1 0 0
ATEX category 3
5
Manual override
Nil: Non-locking
push type (Slotted)
Series
1 56-VQC1000
Coil voltage
5
24VDC
Type of actuation
2-position single (A)(B) 4 2 4-position dual 3-port valve (A) (B) (A) 4 2
B: Locking type
(Slotted)
1
5 1 3 (R1)(P)(R2)
A
Note)
Function
Nil
5 3 (R1) 1 (R2) (P) N.C N.C 4-position dual 3-port valve (A) (B) (B) 4 2 5 3 (R1) 1 (R2) (P) N.O N.O 4-position dual 3-port valve (A) (B) (C) 4 2 5 (R1) N.C 3 1 (R2) (P) N.O
C: Locking type
(Manual)
B
Note)
5 1 3 (R1)(P)(R2)
C
Note)
Seal type
0 1
Metal seal Rubber seal
4
5 1 3 (R1)(P)(R2)
Note) ''56-'' solenoid valve should be installed in ''56-VV5QC11'' manifold. Power consumption when starting is 1W, when maintaining 0.35W.
5 1 3 (R1)(P)(R2)
93
Series
56-VQC2000
II 3GD EEx nA II T5X T85C IP67
For more details, other specifications, dimensions, see the specific catalogue.
M F/T L S Kit
Options
B D D K N R S T
Kit
Manifold model
1
Plug-in unit
Stations
01
1 station
None All stations with back pressure check valve With DIN rail (rail length: standard) With DIN rail (rail length: special) Special wiring specifications (except for double wiring) With name plate External pilot Direct exhaust with built-in silencer Branched P and R ports on U side
The maximum number of stations differs depending on the electrical entry (refer to Electrical entry/Cable length).
COM.
N
() COM.
0 EX50 series
Multiple connector kit (26P) without cable Multiple connector kit (26P) with 1.5m cable 1 to 12 stations Multiple connector kit (26P) with 3.0m cable (24 stations) TD0 Terminal block box kit Multiple connector kit (26P) with 5.0m cable
94
Series 56-VQC
Base-Mounted Type
Plug-in Unit
56 - VQC 2 1 0 0
ATEX category 3
5
Manual override
Nil: Non-locking
push type (Slotted)
Series
2 56-VQC2000
Coil voltage
5
24VDC
Type of actuation
2-position single (A)(B) 4 2 4-position dual 3-port valve (A) (B) (A) 4 2
B: Locking type
(Slotted)
1
5 1 3 (R1)(P)(R2)
A
Note)
Function
Nil
5 3 (R1) 1 (R2) (P) N.C N.C 4-position dual 3-port valve (A) (B) (B) 4 2 5 3 (R1) 1 (R2) (P) N.O N.O 4-position dual 3-port valve (A) (B) (C) 4 2 5 (R1) N.C 3 1 (R2) (P) N.O
C: Locking type
(Manual)
B
Note)
5 1 3 (R1)(P)(R2)
C
Note)
Seal type
0 1
Metal seal Rubber seal
4
5 1 3 (R1)(P)(R2)
Note) ''56-'' solenoid valve should be installed in ''56-VV5QC21'' manifold. Power consumption when starting is 1W, when maintaining 0.35W.
5 1 3 (R1)(P)(R2)
95
Series
56-VQC4000
II 3GD EEx nA II T5X T85C IP67
For more details, other specifications, dimensions, see the specific catalogue.
56 - VV5QC 4 1 08 02 56 - VV5QC 4 1 08 02
Series ATEX category 3
4 56-VQC4000
TD0 N SDA2 N
Nil
M F/T L S Kit
Options
K
None Special wiring specifications (except for double wiring)
Kit
Manifold model
1
Plug-in unit
N S
With name plate (T kit only) Direct exhaust with built-in silencer
Stations
01
1 station
COM.
The maximum number of stations differs depending on the electrical entry (refer to Electrical entry/Cable length).
() COM.
Thread type
Nil F T
Rc G NPT
EX500 series
Multiple connector kit (26P) without cable Multiple connector kit (26P) with 1.5m cable 1 to 12 stations Multiple connector kit (26P) with 3.0m cable (16 stations) TD0 Terminal block box kit Multiple connector kit (26P) with 5.0m cable
SDA2 PROFIBUS-DP
96
Series 56-VQC
Base-Mounted Type
Plug-in Unit
56 - VQC 4 1 0 0
ATEX category 3
5
Manual override
Nil: Non-locking
push type (Slotted)
Series
4 56-VQC4000
Type of actuation
2-position single (A)(B) 4 2 3-position exhaust center (A)(B) 4 2
B: Locking type
(Slotted)
1
5 1 3 (R1)(P)(R2)
4
5 1 3 (R1)(P)(R2)
Coil voltage
5
24VDC
5 2
5 1 3 (R1)(P)(R2) 2-position double (rubber) (A)(B) 4 2
6
5 1 3 (R1)(P)(R2)
Function
Nil R
Standard type (1W) External pilot
5 1 3 (R1)(P)(R2)
3
5 1 3 (R1)(P)(R2)
Seal type
0 1
Metal seal Rubber seal
Note) ''56-'' solenoid valve should be installed in ''56-VV5QC41'' manifold. Power consumption when starting is 1W, when maintaining 0.35W.
97
56-VQC1000
Kit (Multiple Connector Kit)
56-VV5QC11
(L4) (L3) L2 72 65 (12) 13 1.5 L1 P=10.5 Indicator light 28 1.5
(5.25)
Manual override
93.5
(35)
=2 20
(40)
D SIDE
STATIONS
U SIDE 2xC8:3(R)EXH.port C8:One-touch fitting for 8 DIN rail clamp screw 18.5 (7.5) 40.5 (12) 62.5
60
18
20.5 2nxC3,C4,C6,M5<4(A),2(B) Port> C3:One-touch fitting for 3.2 C4:One-touch fitting for 4 C6:One-touch fitting for 6 M5:M5 Threads P=10.5 34
Formulas L1 = 10.5n + 45 L2 = 10.5n + 123 (1~12 stations w/1 power saving unit) L2 = 10.5n + 144 (13~24 stations w/2 power saving unit)
L L1 L2 L3 L4
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 55.5 66 76.5 87 97.5 108 118.5 129 139.5 150 160.5 171 181.5 192 202.5 213 223.5 234 244.5 255 265.5 276 286.5 297 133.5 144 154.5 165 175.5 186 196.5 207 217.5 228 238.5 249 280.5 291 301.5 312 322.5 333 343.5 354 364.5 375 385.5 396 162.5 175 175 187.5 200 212.5 225 237.5 237.5 250 262.5 275 300 312.5 325 337.5 350 362.5 375 375 387.5 400 412.5 425 173 185.5 185.5 198 210.5 223 235.5 248 248 260.5 273 285.5 310.5 323 335.5 348 360.5 373 385.5 385.5 398 410.5 423 435.5
98
7.5 9.5
(5.5)
66 75
S
(12) 13
56-VQC1000
Kit (Serial Transmission Kit) Decentralised Serial wiring
Manual override
PWR
93.5
COM
(35)
(40)
EX500 series
(5.5)
66
=9
SI unit
STATIONS
60
=2 7.5 (12) (7.5) 20.5 2nxC3,C4,C6,M5<4(A),2(B) Port> C3:One-touch fitting for 3.2 C4:One-touch fitting for 4 C6:One-touch fitting for 6 M5:M5 Threads P=10.5 34 2xC8:1(P)SUP.port C8:One-touch fitting for 8 Formulas L1 = 10.5n + 45 L2 = 10.5n + 114.5 (1~12 stations w/1 power saving unit) L2 = 10.5n + 135.5 (13~16 stations w/2 power saving unit) n: Stations (Max. 16 stations)
75
L L1 L2 L3 L4
9.5
18.5
25
40.5
99
T
(12) 13
56-VQC1000
Kit (Terminal Block Box Kit)
(L4) (L3) L2 124 7 1 21 1.5 Indicator light
U side
56-VV5QC11
(5.25) L1 P=10.5 28 1.5
Manual override
(59)
Power saving unit 2xM5 Mounting holes 2xG3/4" Conduit port D SIDE STATIONS
1 2 3 4 5 6 7 8 n
77.7
DIN rail clamp screw 18.7 25 40.5 62.5 20.5 34 2xC8:1(P)SUP.port C8:One-touch fitting for 8 n: Stations (Max. 20 stations)
3 X
B B B B B B B B
45.5
X 12 P 1A
12 P 1
(12) (7.5)
35
2nxC3,C4,C6,M5<4(A),2(B) Port> C3:One-touch fitting for 3.2 C4:One-touch fitting for 4 C6:One-touch fitting for 6 M5:M5 Threads
P=10.5
Formulas L1 = 10.5n + 45 L2 = 10.5n + 175.5 (1~12 stations w/1 power saving unit) L2 = 10.5n + 196.5 (13~20 stations w/2 power saving unit)
L L1 L2 L3 L4
3 4 5 6 7 1 2 55.5 66 76.5 87 97.5 108 118.5 186 196.5 207 217.5 228 238.5 249 212.5 225 237.5 237.5 250 262.5 275 223 235.5 248 248 260.5 273 285.5
12 13 14 15 171 181.5 192 202.5 301.5 333 343.5 354 325 362.5 375 375 335.5 373 385.5 385.5
18 19 20 234 244.5 255 385.5 396 406.5 412.5 425 437.5 423 435.5 448
100
7.7 9.5
(40) (5.5)
(35) 66 75 93.5
126 80
A B A B A B A B A B A B A
D side
M
(12) 13
56-VQC2000
Kit (Multiple Connector Kit)
(L4) (L3) L2 68 76.5 21 1 34.5 L1 Indicator light Manual override P=16 38.5 1
56-VV5QC21
127
(5.5) =3.5 (53.5) 80 105.5 =5.5 4xM5 Mounting holes D SIDE 2xC10:3(R)EXH.port C10:One-touch fitting for 10 DIN rail clamp screw STATIONS
1 2 3 4 5 6 7 8 n
U SIDE
(35)
18
10
(12) (7.5)
2xC10:1(P)SUP.port C10:One-touch fitting for 10 2nxC4,C6,C8<4(A),2(B) Port> C4:One-touch fitting for 4 C6:One-touch fitting for 6 C8:One-touch fitting for 8
25 P=16 45
Formulas L1 = 16n + 57 L2 = 16n + 131.5 (1~12 stations w/1 power saving unit) L2 = 16n + 152.5 (13~24 stations w/2 power saving unit)
L L1 L2 L3 L4
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 1 73 89 105 121 137 153 169 185 201 217 233 249 265 281 297 313 329 345 361 377 393 409 425 441 147.5 163.5 179.5 195.5 211.5 227.5 243.5 259.5 275.5 291.5 307.5 323.5 360.5 376.5 392.5 408.5 424.5 440.5 456.5 472.5 488.5 504.5 520.5 536.5 175 187.5 200 225 237.5 250 275 287.5 300 312.5 337.5 350 387.5 400 412.5 437.5 450 462.5 487.5 500 512.5 525 550 562.5 185.5 198 210.5 235.5 248 260.5 285.5 298 310.5 323 348 360.5 398 410.5 423 448 460.5 473 498 510.5 523 535.5 560.5 573
13.5
25
60
49.5
76.5
101
S
(12) 13
56-VQC2000
Kit (Serial Transmission Kit) Decentralised Serial wiring
(L4) (L3) L2 76.5 21 59.5 21 34.5 1 L1 Indicator light Manual override P=16 38.5 1
(5.25)
127
PWR COM
(53.5)
EX500 series
(5.5)
=3.5
SI unit
U SIDE
2xC10:3(R)EXH.port C10:One-touch fitting for 10 C1(M12) C2(M12) DIN rail clamp screw 0 76.5 60 49.5 25 P=16 45 Formulas L1 = 16n + 57 L2 = 16n + 123 (1~12 stations w/1 power saving unit) L2 = 16n + 144 (13~16 stations w/2 power saving unit) n: Stations (Max. 16 stations) 1 25 10 30 2xC10:1(P)SUP.port C10:One-touch fitting for 10 2nxC4,C6,C8<4(A),2(B) Port> C4:One-touch fitting for 4 C6:One-touch fitting for 6 C8:One-touch fitting for 8
L L1 L2 L3 L4
(12)
(7.5)
13.5
102
=5.5
(35) 80 105.5
T
(12) 13
56-VQC2000
Kit (Terminal Block Box Kit)
(L4) (L3) L2 1 (5.25) L1 P=16 38.5
56-VV5QC21
120 76.5 7
U side
D side
132.5 80
(59)
(5.5)
U SIDE
45.5 25 10
(12) (7.5)
2xC10:1(P)SUP.port C10:One-touch fitting for 10 2nxC4,C6,C8<4(A),2(B) Port> C4:One-touch fitting for 4 C6:One-touch fitting for 6 C8:One-touch fitting for 8
25 P=16 45
Formulas L1 = 16n + 45 L2 = 16n + 184 (1~12 stations w/1 power saving unit) L2 = 16n + 205 (13~20 stations w/2 power saving unit)
L L1 L2 L3 L4
1 2 3 73 89 105 200 216 232 225 237.5 262.5 235.5 248 273
13.5
30 49.5
=5.5
(35) 80 105.5
103
56-VQC4000
Kit (Multiple Connector Kit)
56-VV5QC41
L2 69 21 L1 Indicator light Manual override (6.5) P=25 65.5
9 143 74.5
B B B B B
D SIDE
STATIONS
SMC
SMC
SMC
SMC
SMC
SMC
SMC
60
42.7
15.7
11.5
(6.5)
21.5 38.7
(6.5)
2n-Rc1/4,3/8,C8,C10,C12<4(A),2(B)Port> Rc1/4:Rc1/4 Thread Rc3/8:Rc3/8 Thread C8 :One-touch fitting for 8 C10:One-touch fitting for 10 C12:One-touch fitting for 12
Formulas L1 = 25n + 106 L2 = 25n + 181.5 (1~12 stations w/1 power saving unit) L2 = 25n + 202.5 (13~16 stations w/2 power saving unit)
L L1 L2
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 131 156 181 206 231 256 281 306 331 356 381 406 431 456 481 506 206.5 231.5 256.5 281.5 306.5 331.5 356.5 381.5 406.5 431.5 456.5 481.5 527.5 552.5 577.5 602.5
104
12 20.5 43.5
18
10
163
A A
A A
A A
A A
A A
A A
A A
56-VQC4000
Kit (Serial Transmission Kit) Decentralised Serial wiring
21
PWR COM
9
EX500 series
B B B B B
9 SI unit Power saving unit (101) D SIDE STATIONS 1 2 3 4 5 6 7 8 n U SIDE 2xRc3/4 3(R)EXH.port 2xRc1/2 1(P)SUP.port
SMC SMC SMC SMC SMC SMC SMC
M12
0
2 B 2 B 2 B 2 B 2 B 2 B 2 B 2 B
10
4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A
60 42.7 15.7 12
11.5
M12
(6.5)
21.5 38.7
(6.5)
2n-Rc1/4,3/8,C8,C10,C12<4(A),2(B)Port> Rc1/4:Rc1/4 Thread Rc3/8:Rc3/8 Thread C8 :One-touch fitting for 8 C10:One-touch fitting for 10 C12:One-touch fitting for 12
Formulas L1 = 25n + 106 L2 = 25n + 173 (1~12 stations w/1 power saving unit) L2 = 25n + 194 (13~16 stations w/2 power saving unit)
L L1 L2
1 131 198
2 156 223
3 181 248
4 206 273
5 231 298
6 256 323
7 281 348
8 306 373
9 331 398
10 356 423
11 381 448
12 406 473
13 431 519
14 456 544
15 481 569
12 20.5 43.5
16 506 594
143 163
A
A
A
A
A
A
A
A
A
A
A
A
A
A
105
56-VQC4000
Kit (Terminal Block Box Kit)
56-VV5QC41
L2 7 100.5 Indicator light L1 P=25 65.5
6.5
Manual override
A
B
80
34.5
9 Power saving unit D SIDE STATIONS 1 2 3 4 5 6 7 8 n U SIDE 2xRc3/4 3(R)EXH.port 2xRc1/2 1(P)SUP.port
SMC SMC SMC SMC SMC SMC SMC 2 B 2 B 2 B 2 B 2 B 2 B 2 B 2 B 4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A
(101)
11.5
(6.5)
21.5 38.7
(6.5)
2n-Rc1/4,3/8,C8,C10,C12<4(A),2(B)Port> Rc1/4:Rc1/4 Thread Rc3/8:Rc3/8 Thread C8 :One-touch fitting for 8 C10:One-touch fitting for 10 C12:One-touch fitting for 12
Formulas L1 = 25n + 106 L2 = 25n + 213 (1~12 stations w/1 power saving unit) L2 = 25n + 234 (13~16 stations w/2 power saving unit)
L L1 L2
1 131 238
2 156 263
3 181 288
4 206 313
5 231 338
6 256 363
7 281 388
8 306 413
9 331 438
10 356 463
11 381 488
12 406 513
13 431 559
14 456 584
12 20.5 43.5
15 481 609
106
10
143 163
9
U side
A A A A A A A
D side
16 506 634
107
Series
56-EX500
For more details, other specifications, dimensions, see the specific catalogue.
II 3GD EEx nA II T5 X 5C Ta 45C IP67 (SI Unit 56-EX500-Q01, 56-EX500-S01) II 3GD EEx nA II T5 X 5C Ta 45C IP65 (Input Unit 56-EX500-IB1, Input Block 56-EX500-IE)
How to Order
56 - EX500
ATEX category 3
G PR1A
Communication protocol
PR1A PROFIBUS-DP
108
Series 56-EX500
EEX500
E T M
IB1
E 4
Unit side
56
-EX
Stations
1 1 station 4 stations
50
0-I
B1
Input block
56
ATEX category 3
- EX500
Block type
1 2 3 4 5 6
IE 1
When ordering an input block manifold, enter the Input manifold part no. + Input block part no. together. The input block , end block and DIN rail are included in the input manifold. Refer to How to Order below.
M8 connector, PNP specification M8 connector, NPN specification M12 connector, PNP specification M12 connector, NPN specification 8-point integrated type, M8 connector, PNP specifications 8-point integrated type, M8 connector, NPN specifications
Current source type input block (PNP input block) or Current sink type input block (NPN input block) M12 connector (8 pins, plug) Maximum 4 blocks 24 VDC 0.3 A maximum 100 mA or less (at rated voltage) 1A Typ. for each unit (shut off power supply) To restart, remove power to the GW unit once, then reapply it. IP65 100 (Input unit + end block)
M8 connector (3 pins) or, M12 connector (4 pins) 2 inputs/8 inputs (M8 only) 24 VDC 15 V to 26.4 V 0 V to 5 V 5 mA Typ. 1.5 mA 0 V to 8 V 19 V to 26.4 V 5 mA Typ. 1.5 mA 1 m sec. or less Green LED Not provided Maximum 30 mA/Sensor
+5 to +45C at 35% to 85% RH (without condensation)
IP65 [For M8: 20] [For M12: 40] [8 point integrated type, for M8: 55]
109
Series 56-EX500
Dimensions 8 point integrated type Input Block
47 8 31 (Pitch) P=12
21
DIN rail
35
5.5
(12.5) 5
44.2
35
5.5
32.2
56-EX500-IB1
(7.5)
39.7
60
44.2
Stations
L1 L2 L3
1 2 3 4 82 102 122 142 100 112.5 137.5 162.5 173 110.5 123 148
110
32.2
56-EX500-IB1
(7.5)
46.9
49
Series 56-EX500
35
5.5
44.2
56-EX500-IB1
(7.5)
Stations
L1 L2 L3
35
5.5
32.2
39.7
49
5 L
0 1 2 3 4
M8 input block(m) Connector type: For M8 Input 0 1 2 3 4 Block 0 1 2 3 (n=1 to 4) 1 2 3 4 L dimension 2 3 4 4 5 Connector type: For M8 and M12 6
mixed (m+n=2 to 4)
(7.5)
39.7 46.9
44.2
111
112
Safety Instructions
The following safety instructions are intended to prevent hazardous situations and/or equipment damage. The instructions indicate the level of potential hazard by labeling "Caution", "Warning", or "Danger". To ensure safety, please observe all safety practices, including ISO 4414 Note 1), JIS B8370 Note 2).
Caution : Operator error could result in injury or equipment damage. Warning : Operator error could result in serious injury or loss of life. Danger : In extreme conditions, there is a possibility of serious injury or loss of life.
Note 1) ISO 4414: Pneumatic fluid power -- Recommendations for the application of equipment to transmission and control systems. Note 2) JIS B 8370: Pneumatic system axion
Warning
1. The compatibility of pneumatic equipment is the responsibility of the person who designs the pneumatic system or decides its specifications.
Since the products specified here are used in various operating conditions, their compatibility with a specific pneumatic system must be based on specifications or post analysis and/or tests to meet a specific requirement.
4. Contact SMC if the product will be used in any of the following conditions.
1. Conditions and environments beyond the given specifications or if product is used outdoors. 2. Installation on equipment in conjunction with atomic energy, railway, air navigation, vehicles, medical equipment, food and beverage, recreation equipment, emergency stop circuits, press applications or safety equipment. 3. An application which has the possibility of having a negative affect on people, property, or applications with special safety requirements.
113
Common Precautions
Be sure to read before handing.
3. Drain
If condensation in the air filter is not emptied on a regular basis, condensation that flows to the outlet side can cause a malfunction. If it is difficult to check and remove, installation of a filter with an auto-drain function is recommended. Refer to Best Pneumatics for details on compressed air quality.
Selection
Warning
1. Confirm specifications.
Products represented in this catalogue are designed for use in compressed air applications only (including vacuum), unless otherwise indicated. Do not use the products outside of their designed parameters. Contact SMC when using the product with fluids other than compressed air (including vacuum).
Installation
Environment
Warning
1. Do not install unless the safety instructions have been read and understood.
Keep this catalogue on file for future reference.
Warning
1. Do not use in an environment where the product is directly exposed to corrosive gases, chemicals, sea water, water or steam. 2. In locations which receive direct sunlight, provide a protective cover, etc. 3. Do not operate in locations where vibration or impact occurs. 4. Do not use in locations where radiated heat will be received from nearby heat sources. 5. Avoid striking the product with a metallic object.
2. Maintenance
When installing the product, allow for maintenance access.
3. Tightening torque
When installing the product, follow the torque specification.
Piping
6. Avoid using this product in a non-explosive environment which can become explosive due to air leakage.
Caution
1. Before piping
Before piping is connected, it should be thoroughly blown out with air (flushing) or washed to remove chips, cutting oil and other debris from inside the pipe.
Maintenance
2. Sealant tape
When installing piping or a fitting into a port, make sure that the sealant material does not clog the pressure port. Leave the first 1.5 to 2 thread turns exposed at the end of the pipe/ fitting when using sealant tape.
Warning
1. Maintenance procedures are outlined in the operation manual.
Failure to follow proper procedures can result in product malfunction and or lead to damage to the equipment or machine.
2. Maintenance
Air Supply
If handled improperly, compressed air can be dangerous. Assembly, handling and repair of pneumatic systems should only be performed by qualified personnel.
Warning
1. Operation fluid
Consult with SMC when using the product in applications which use fluids other than compressed air (including vacuum). Regarding products for general fluids, consult with SMC regarding applicable fluids.
3. Drain
Remove condensation from the filter bowl on a regular basis.
114
Series
Category
VH200/201/400/401 AR10/20/25/30/40/50/60 ARM2500/3000 AF10/20/30/40/50/60 AFM20/30/40 AFD20/30/40 AW10/20/30/40 AL10/20/30/40/50/60 VHK2 VHS20/30/40/50 Y24~54 AS AK,AKH VR12 AQ KQ T, TS, TU IL100 IL201/211/220 IR1000~3000 IRV1000~3000 IW212~217 GD40 CCT ADH4000 AFF2B~AFF75B AM150~850 AMC310~910 AMD150~850, AMD800~1000 AME150~850 AMF150~1000 AMG150~850 AMH150~850 AMJ AMP AMR3000~6000 AN ANA1, ANB1 IDG ZFA, ZFB ZFC ZH ZP, ZPR, ZPR*F, ZPT, ZPT*F, ZPX, ZPY ZU
Consult SMC for individual part numbers and details of compliant models.
Others
Out of scope
1)
115
EUROPEAN SUBSIDIARIES:
Austria SMC Pneumatik GmbH (Austria). Girakstrasse 8, A-2100 Korneuburg Phone: +43 2262-62280, Fax: +43 2262-62285 E-mail: office@smc.at http://www.smc.at
France SMC Pneumatique, S.A. 1, Boulevard de Strasbourg, Parc Gustave Eiffel Bussy Saint Georges F-77607 Marne La Vallee Cedex 3 Phone: +33 (0)1-6476 1000, Fax: +33 (0)1-6476 1010 E-mail: contact@smc-france.fr http://www.smc-france.fr
Lithuania UAB Ottensten Lietuva Savanoriu pr. 180, LT-2600 Vilnius, Lithuania Phone/Fax: +370-2651602
Slovakia SMC Priemyseln Automatizci, s.r.o. Nmestie Martina Benku 10 SK-81107 Bratislava Phone: +421 2 444 56725, Fax: +421 2 444 56028 E-mail: office@smc.sk http://www.smc.sk
Belgium SMC Pneumatics N.V./S.A. Nijverheidsstraat 20, B-2160 Wommelgem Phone: +32 (0)3-355-1464, Fax: +32 (0)3-355-1466 E-mail: post@smcpneumatics.be http://www.smcpneumatics.be
Germany SMC Pneumatik GmbH Boschring 13-15, D-63329 Egelsbach Phone: +49 (0)6103-4020, Fax: +49 (0)6103-402139 E-mail: info@smc-pneumatik.de http://www.smc-pneumatik.de
Netherlands SMC Pneumatics BV De Ruyterkade 120, NL-1011 AB Amsterdam Phone: +31 (0)20-5318888, Fax: +31 (0)20-5318880 E-mail: info@smcpneumatics.nl http://www.smcpneumatics.nl
Slovenia SMC industrijska Avtomatika d.o.o. Grajski trg 15, SLO-8360 Zuzemberk Phone: +386 738 85240 Fax: +386 738 85249 E-mail: office@smc-ind-avtom.si http://www.smc-ind-avtom.si
Bulgaria SMC Industrial Automation Bulgaria EOOD 16 kliment Ohridski Blvd., fl.13 BG-1517 Sofia Phone:+359 2 9744492, Fax:+359 2 9744519 E-mail: office@smc.bg http://www.smc.bg
Greece S. Parianopoulus S.A. 7, Konstantinoupoleos Street, GR-11855 Athens Phone: +30 (0)1-3426076, Fax: +30 (0)1-3455578 E-mail: parianos@hol.gr http://www.smceu.com
Norway SMC Pneumatics Norway A/S Vollsveien 13 C, Granfos Nringspark N-1366 Lysaker Tel: +47 67 12 90 20, Fax: +47 67 12 90 21 E-mail: post@smc-norge.no http://www.smc-norge.no
Spain SMC Espaa, S.A. Zuazobidea 14, 01015 Vitoria Phone: +34 945-184 100, Fax: +34 945-184 124 E-mail: post@smc.smces.es http://www.smces.es
Czech Republic SMC Industrial Automation CZ s.r.o. Hudcova 78a, CZ-61200 Brno Phone: +420 5 414 24611, Fax: +420 5 412 18034 E-mail: office@smc.cz http://www.smc.cz
Hungary SMC Hungary Ipari Automatizlsi Kft. Budafoki ut 107-113, H-1117 Budapest Phone: +36 1 371 1343, Fax: +36 1 371 1344 E-mail: office@smc-automation.hu http://www.smc-automation.hu
Poland SMC Industrial Automation Polska Sp.z.o.o. ul. Konstruktorska 11A, PL-02-673 Warszawa, Phone: +48 22 548 5085, Fax: +48 22 548 5087 E-mail: office@smc.pl http://www.smc.pl
Sweden SMC Pneumatics Sweden AB Ekhagsvgen 29-31, S-141 71 Huddinge Phone: +46 (0)8-603 12 00, Fax: +46 (0)8-603 12 90 E-mail: post@smcpneumatics.se http://www.smc.nu
Denmark SMC Pneumatik A/S Knudsminde 4B, DK-8300 Odder Phone: +45 70252900, Fax: +45 70252901 E-mail: smc@smc-pneumatik.dk http://www.smcdk.com
Ireland SMC Pneumatics (Ireland) Ltd. 2002 Citywest Business Campus, Naas Road, Saggart, Co. Dublin Phone: +353 (0)1-403 9000, Fax: +353 (0)1-464-0500 E-mail: sales@smcpneumatics.ie http://www.smcpneumatics.ie
Portugal SMC Sucursal Portugal, S.A. Rua de Eng Ferreira Dias 452, 4100-246 Porto Phone: +351 22-610-89-22, Fax: +351 22-610-89-36 E-mail: postpt@smc.smces.es http://www.smces.es
Switzerland SMC Pneumatik AG Dorfstrasse 7, CH-8484 Weisslingen Phone: +41 (0)52-396-3131, Fax: +41 (0)52-396-3191 E-mail: info@smc.ch http://www.smc.ch
Estonia SMC Pneumatics Estonia O Laki 12-101, 106 21 Tallinn Phone: +372 (0)6 593540, Fax: +372 (0)6 593541 E-mail: smc@smcpneumatics.ee http://www.smcpneumatics.ee
Italy SMC Italia S.p.A Via Garibaldi 62, I-20061Carugate, (Milano) Phone: +39 (0)2-92711, Fax: +39 (0)2-9271365 E-mail: mailbox@smcitalia.it http://www.smcitalia.it
Romania SMC Romania srl Str Frunzei 29, Sector 2, Bucharest Phone: +40 213205111, Fax: +40 213261489 E-mail: smccadm@canad.ro http://www.smcromania.ro
Turkey Entek Pnmatik San. ve Tic Ltd. Sti. Perpa Tic. Merkezi Kat: 11 No: 1625, TR-80270 Okmeydani Istanbul Phone: +90 (0)212-221-1512, Fax: +90 (0)212-221-1519 E-mail: smc-entek@entek.com.tr http://www.entek.com.tr
DiskArt 1988
Finland SMC Pneumatics Finland OY PL72, Tiistinniityntie 4, SF-02031 ESPOO Phone: +358 (0)9-859 580, Fax: +358 (0)9-8595 8595 E-mail: smcfi@smc.fi http://www.smc.fi
Latvia SMC Pneumatics Latvia SIA Smerla 1-705, Riga LV-1006, Latvia Phone: +371 (0)777-94-74, Fax: +371 (0)777-94-75 E-mail: info@smclv.lv http://www.smclv.lv
Russia SMC Pneumatik LLC. 36/40 Sredny pr. St. Petersburg 199004 Phone.:+812 118 5445, Fax:+812 118 5449 E-mail: smcfa@peterlink.ru http://www.smc-pneumatik.ru
UK SMC Pneumatics (UK) Ltd Vincent Avenue, Crownhill, Milton Keynes, MK8 0AN Phone: +44 (0)800 1382930 Fax: +44 (0)1908-555064 E-mail: sales@smcpneumatics.co.uk http://www.smcpneumatics.co.uk
DiskArt
OTHER SUBSIDIARIES WORLDWIDE: ARGENTINA, AUSTRALIA, BOLIVIA, BRASIL, CANADA, CHILE, CHINA, HONG KONG, INDIA, INDONESIA, MALAYSIA, MEXICO, NEW ZEALAND, PHILIPPINES, SINGAPORE, SOUTH KOREA, TAIWAN, THAILAND, USA, VENEZUELA
http://www.smceu.com http://www.smcworld.com
SMC CORPORATION 1-16-4 Shimbashi, Minato-ku, Tokio 105 JAPAN; Phone:03-3502-2740 Fax:03-3508-2480
Produced and printed by SMC European Marketing Centre 12/04 Specifications are subject to change without prior notice and any obligation on the part of the manufacturer.