Académique Documents
Professionnel Documents
Culture Documents
In fact, the method used by manufacturers and governing associations to determine the moment-of-inertia, I, of a baseball or softball bat is to measure the period of oscillation when the bat is allowed to swing as a pendulum from a pivot point 6-inches from the knob end of the bat, and then calculate the moment-of-inertia from the above equation.[1] Instead of being distributed throughout the entire object, let the mass of the physical
pendulum M be concentrated at a single point located at a distance L from the pivot point. This point mass swinging from the end of a string is now a "simple" pendulum, and its period would be the same as that of the original physical pendulum if the distanceL was
This location L is known as the "center-ofoscillation", since it represents the length of an equivalent simple pendulum with the same total mass and that has the same period as the actual phyiscal object. The exact location of this special point depends on the location of the pivot - a fact which will be very important to the application of this concept to a baseball or softball bat, as we will see below. One special thing about this location is that if the object (bat) were inverted and pivoted at the centerof-oscillation it would have exactly the same period as it does when pivoted from its original location. The second special property about this location is if a horizontal impulsive force is applied to the center-of-oscillation, no reaction force is felt at the pivot point. Therefore, this location is also known as the center-of-percussion or COP.
associated with feel, of a baseball bat. However, there is a problem with this identification because the location of the COP is completely dependent on the location of the pivot point. For every location on the handle there is a corresponding location on the bat barrel which acts as a centerof-percussion for that specific handle location. The traditional assumption, supported by some early experimental studies,[8] is that when a player swings at a ball, the bat pivots about a point on the handle under the hands, roughly 6-inches from the knob. As we will see later in this article the most recent experimental evidence reveals that the pivot point is neither on the handle under the hands, nor at the wrist of the player swinging the bat. First, though, I want to take a look at how this special location on the bat has affected the manner in which bat performance is measured.
values around 1.30 or higher. The legal limit set by USSSA, ISF and NSF is BPF 1.20. Prior to 2004, the Amateur Softball Association (ASA) used the same ASTM standard, but used a formula to combine the BBCOR with a prediction of bat swing speed to obtain a predicted Batted-Ball Speed (BBS). Bats which produced a BBS of 85mph or less were considered legal bats. Little League youth bats are tested with the same apparatus, only using baseballs, and must pass with a BPF rating of 1.15 or lower. 2. Baseball bats used by high school and college players under NCAA and the National Federation of State High School Associations rules must pass a similar test, known as the Ball Exit Speed Ratio, or BESR test. This test uses a special machine called the Baum Hitting MachineTM to swing a bat at 68 mph towards a ball which is moving towards the bat at 70 mph. After impact the ball passes through a speed trap and the "ball exit speed" is measured. Current ball exit speed standards for college and high school bats are 97 mph and 94 mph respectively.
The problem with these standardized tests is they all require the impact between ball and bat to occur at the experimentally determined center-ofpercussion of the bat relative to a pivot point on the handle 6-inches from the knob. As early as 1986, theoretical analyses showed that the COP was not the location on a wood bat where the resulting ball speed would be maximized,[6] but experimental evidence was not yet available to confirm this. Most researchers believed that because the COP location was widely held to be the location where impacts felt the best to the hitter, and thus the term "sweet spot," it was assumed that this location would provide the best assessment of performance for hollow bats as well. However, in the year 2000 important experimental results were published showing that, at least for hollow softball bats tested using the BPF test, the center-ofpercussion was not the location where maximum ball speed Comparing the location of the COP and maximum batted-ball speed occurs.[10] for several aluminum, composite, and wood slow-pitch softball bats.
The figure at right shows the locations of the center-of-percussion (small black dots) and the experimentally determined location producing the highest batted-ball speed (big white circles) for a variety of slow-pitch softball bats. The data in the figure includes two wood bats, and a variety of aluminum and composite hollow bats covering a range of performances. Notice that for only one of the bats is the location of maximum batted-ball speed within 0.25-inches of the center-ofpercussion. Also notice that for the two wood bats the max-BBS location is further from the barrel end than the COP, while for almost all of the hollow bats the COP is closer to the barrel end (the one exception is the data point at the top of the figure which is for a very low performing 1970's vintage aluminum bat).
Data showing that adding mass to the knob shifts the location of the COP without moving the maximum performance location. Data courtesy of Alan Nathan and Richard Brandt.
ball comes off the bat. The blue data points are for an unmodified bat. Notice that the location of maximum performance is at 7inches from the barrel end, while the location of the COP for this bat is only 5.75 inches from the barrel end. If the bat was tested at the COP the measured BBCOR would be 0.595 instead of the actual maximum value of 0.600. The red data points show the effect of adding 3-ounces of mass to the knob of the handle. Notice that the performance curve is essentially unaffected - that is, the maximum BBCOR is still 0.600 at a distance of 7-inches from the barrel end of the bat. But, the location of the COP has now shifted almost an inch closer to the barrel end. So, if the altered bat was tested at its COP the measured BBCOR would only be 0.575 instead of the actual maximum 0.600. The reason for this shift in the location of the COP is the fact that the location of the COP depends on the total mass of the bat as well as the balance point and the momentof-inertia (see the equation defining the distance L above). Adding 3 ounces to the knob of the bat increases the weight but also shifts the balance point towards the handle so that the moment-of-inertia does not change. As a result the performance of the bat, which depends on the inertial properties of the bat, is unaffected while the location of the COP is significantly changed. Similarly, by moving a small amount of mass from the barrel end of the bat to the handle end, the balance point and moment-
of-inertia could be manipulated without altering the total weight of the bat. By changing the MOI and balance point, the location of the center-of-percussion also changes. Clever manufacturers began designing bats which would pass the BPF and BESR tests, which were conducted at the bat's COP, but which would perform significantly higher in the field. Fingers should not be pointed only at manufacturers, however. I have been informed by engineers from two different bat companies that they were told by an association that if they were to shift a fraction of an ounce of mass from the barrel end to the handle end, a specific bat model would end up passing the test and wouldn't end up being banned.
When I defined the center-ofpercussion earlier, I stated that the location of the COP depends on the location of the pivot point. For the last twenty years researchers have followed the assumption that the pivot point is under the hands, or at least at the wrists, during the rotation and impact with the ball.[8] Recent experiments have conclusively shown this not to be the case. Two very thorough experimental field studies - one for softball bats[12] and the other for baseball bats[13] - with real players swing bats at Experimental locations of the pivot point of a swung softball bat at pitched balls used 3-D video systems the instant of impact with the ball. Data courtesy of Lloyd Smith, carefully tracked the motion of the bat Sport Sciences Laboratory, Washington State University. during the entire swing. Both studies showed that during the impact with the ball the instantaneous center of rotation (ie, the pivot point) is not at the 6-inch point on the handle, nor is it at the wrists. Instead it is located about 2.5 inches beyond the knob end of the handle and about 2.5 inches off of the axes of the bat. The figure at right shows the raw data collected from a dozen Class-A slow-pitch softball players, each taking about two dozen good hits. The various colored data points represent individual players. The larger black dot in the middle of the data points is the average pivot location for all hits across all players. The scatter of the data indicates that the pivot point varies not only from player to player, but also from swing to swing for each player. Notice that none of the measured pivot points is within 2 inches of the black dot on the handle which is at the 6-inch point used to measure the COP and which was formerly used to determine the point on the barrel where performance testing should occur.
So, there is pretty overwhelming evidence that the COP has nothing whatsoever to do with the measured performance of a baseball or softball bat. However, from its definition as being the impact location that results in zero net force at the pivot point, the COP is still often referred to as being the "sweet spot" at least in terms of feel. Hitting the ball at the center-of-percussion on the bat should minimize the sting felt in the hands. Early research by Brody[6] and Noble[14] suggests that the best place for the ball to impact the bat with minimal force exerted in the hands is between COP relative to the 6-inch point on the handle and the node of the first bending mode of vibration. Robert Adair has long argued that its only the location of the node of the first bending vibration of the bat which influences feel.[15] Rod Cross conducted numerous experiments on bats and tennis racquets and concluded that the most comfortable location is somewhere between the nodes of the first two bending modes, with the location of the node of the second bending mode being more important.[16] The issue is somewhat controversial and has raised some interesting banter back and forth between holders of the various viewpoints.[17] It is true that the COP is the location where no net force is exerted at the pivot point. However, the recently discovered fact that the actual pivot point at the instant of collision is not on the hands under the handle, but about 2.5 inches completely beyond the end of the handle, renders the COP relative to the 6-inch point on the handle irrelevant. If the defacto pivot point during the collision is not on the handle, then there is no point on the handle where the net force is exactly zero and the COP is meaningless as a definition of the sweet spot. Recent experimental evidence for handheld tennis racquets[18-19] agrees with the results for baseball and softball bats. The location of the pivot point is not under the hands. Thus, the center-of-percussion relative to a pivot point on the handle is not representative of the actual playing conditions and cannot be the "sweet spot" location that feels best.
References
[1] ASTM F 1881-04: Standard Test Method for Measuring Baseball Bat Performance Factor, and ASTM F 189004: Standard Test Method for Measuring Softball Performance Factor, Annual Book of ASTM Standards, Vol. 15.07 (ASTM International, West Conshohocken, PA, 2004). The procedures for measuring moment-of-inertia and locating the center-of-percussion will soon be incorporated into a separate standard, ASTM F 2398: Test Method for Measuring Moment of Inertia and Center of Percussion of a Baseball or Softball Bat. [2] R. Resnick, D. Halliday, and K.S. Krane, Physics 5th Ed., (John Wiley & Sons, 2002) p.382-383. [3] L.A. Bloomfield, How Things Work, The Physics of Everyday Life, (John Wiley & Sons, 1997) p.100. [4] K. R. Symon, Mechanics, 3rd Ed., (Addison-Wesley, 1971) p. 216-218. [5] F.W. Sears, Mechanics, Heat and Sound, (Addison-Wesley, 1950) p. 274-276. [6] H. Brody, "The sweet spot of a baseball bat," American Journal of Physics, 54(7), 640-643 (1986). [7] For a similar description of the center-of-percussion in a tennis racket, see Rod Cross's "Physics of Tennis" website: http://www.physics.usyd.edu.au/~cross/tennis.html [8] L. Noble and X. Eck, "Emperical determination of the axis of percussion of softball and baseball bats," in Biomechanics IX-B, D.A. Winter, R.W. Norman, R.P. Wells, K.C. Hayes, and E. Patla (Eds.), Champaign, IL (1985) pp. 516-520. [9] A history of bat performance testing for NCAA Baseball may be found in: S. R. Hagwell, "Bat issue goes extra innings in Divisions II and III," The NCAA News, (February 1, 1999). [10] L.V. Smith, "Evaluating baseball bat performance," Sports Engineering, 4, p.205-214 (2001). [11] K. Hawes, "New focus on potential loophole involving swing speed," The NCAA News, (April 10, 2000). [12] Smith, L, Broker, J, Nathan, A, A Study of Softball Player Swing Speed, Sports Dynamics Discovery and Application, Edited by A. Subic, P. Trivailo, and F. Alam, RMIT University, Melbourne Australia, pp. 12-17 (2003) [13] J.J. Crisco, R.M. Greenwald, L.H. Penna, and K.R. Saul, "On Measuring the Performance of Wood Baseball Bats," in The Engineering of Sport, A.J. Subic and S.J. Haake (Eds.), pp. 193-200 (Blackwell Science, 2000) [14] L. Noble and H. Walker, "Baseball bat inertial and vibrational characteristics and discomfort following ball-bat impacts," Journal of Applied Biomechanics, 10, p.132-144 (1994). [15] R.K. Adair, The Physics of Baseball, 3rd Ed., (Harper Collins, 2002). [16] R. Cross, "The sweet spot of a baseball bat," American Journal of Physics, 66(9), 771-779 (1998). [17] R.K. Adair, "Comment on The sweet spot of a baseball bat," American Journal of Physics, 69(2), 229-230 (2001); R. Cross, "Respons to Comment on The sweet spot of a baseball bat," American Journal of Physics, 69(2), 231232 (2001) [18] H. Hatze, "The center of percussion of tennis rackets: a concept of limited applicability," Sports Engineering, 1, p.17-25 (1998). [19] R. Cross, "Center of percussion of hand-held implements," American Journal of Physics, 72(5), p.622-630 (2004).