Académique Documents
Professionnel Documents
Culture Documents
The items in the setting code list can be set or changed in this setting mode (08).
Procedure 1
[CANCEL] [0][8] [POWER] [Digital key] (Code) [START] [Digital key] *[FUNCTION CLEAR] Sets or changes value [ENTER] [POWER] OFF/ON or (Exit) [INTERRUPT] (Stores value in RAM)
Procedure 2
[0][8] [POWER] [Digital key] (Code) [START] [ENTER] or [INTERRUPT] Adjustment value cannot be changed [POWER]OFF/ON (Exit)
Procedure 3
[0][8] [POWER] [Digital key] (Code) [START] [ENTER] or (Automatic setting) [INTERRUPT] (Stores value in RAM) [POWER] OFF/ON (Exit)
[CANCEL] or [CLEAR]
Procedure 4
[CANCEL] [START] [0][8] [POWER] [Digital key] (Code) [START] [Digital key] (Sub-code) [START] [ENTER] or [Digital key] * [FUNCTION CLEAR] [INTERRUPT] (Stores value Sets or in RAM) changes value [CLEAR] (Corrects value) [POWER] OFF/ON (Exit)
Procedure 5
[CANCEL] [0][8] [POWER] [Digital key] (Code) [START] [Digital key] *[HELP] Sets or changes value [ENTER] [POWER] OFF/ON or (Exit) [INTERRUPT] (Stores value in RAM)
2 - 54
Procedure 7
[CANCEL] [0][8] [POWER] [Digital key] (Code) [START] [Digital key] (Setting) [ENTER] or (HDD formatting) [INTERRUPT] (Stores value in RAM)
Procedure 9
[CANCEL] [0][8] [POWER] [Digital key] (Code) [START] [ENTER] [POWER] OFF/ON or (Exit) [INTERRUPT] (Stores value in RAM) [CLEAR] (Corrects value)
[Select icon]
Procedure 10
[CANCEL] [0][8] [POWER] [Digital key] (Code) [START] [Digital key] (1st setting) [START] [Digital key] (2nd setting) [POWER] [ENTER] or OFF/ON [INTERRUPT] (Exit) (Stores value in RAM) [CLEAR] (Corrects value)
Procedure 11 and 12
[CANCEL] [0][8] [POWER] [Digital key] (Code) [Digital key] or [ENTER] [START] [Software keyboard] *2(Stores value in RAM) *1 [MONITOR/PAUSE] Sets or changes value [CLEAR] (Corrects value)
*1. Press [MONITOR/PAUSE] to enter -, when entering telephone number. *2. The data are stored in SYS-RAM in procedure 11 and stored in NIC-RAM in procedure 12. Procedure 14
[CANCEL] [0][8] [POWER] [Digital key] (Code) [START] [Digital key] (Sub-code) [START] [ENTER] or [INTERRUPT] Adjustment value cannot be changed [POWER] OFF/ON (Exit)
2 - 55
Notes: The digit after the hyphen in Code of the following table is a sub code. In RAM, the NVRAM of the board in which the data of each code is stored is indicated. M stands for the LGC board, SYS and UTY stands for the SYS board and NIC stands for the NIC board.
Setting mode (08) Default Func- <Accepttion able value> ALL <13 digits>
Code 200
Classification General
RAM -
Contents Year/month/date/day/ hour/minute/second Example: 03 07 0 13 13 27 48 Day - 0 is for Sunday. Proceeds Monday through Saturday from 1 to 6. 0: EUR 1: UC 2: JPN 0: No external counter 1: Coin controller 2: Copy key card 3: Key copy counter 0: For factory shipment 1: For line * Field: 0 must be selected Timer to return the equipment to the default settings when the [START] button is not pressed after the function and the mode are set 0: Not cleared 1 to 10: Set number x 15 sec. Timer to automatically switch to the Auto power save mode when the equipment has not been used 0: Invalid 6: 3min. 7: 4min. 8: 5min. 9: 7min. 10: 10min. 11: 15min. 12: 20min. 13: 30min. 14: 45min. 15: 60min.
Procedure 5
201
General
Destination selection
ALL
202
ALL
203
ALL
204
User interface
ALL
SYS
205
User interface
ALL
SYS
2 - 56
Code 206
Setting mode (08) Default Func- <AcceptItems tion able value> Auto Shut Off Mode timer ALL Refer to content setting (Auto Shut Off Mode/Sleep Mode) <0-20>
RAM SYS
Contents Timer to turn OFF the power or to enter the Sleep Mode automatically when the equipment has not been used (Refer to 08-601) 0: 3min. 1: 5min. 2: 10min. 3: 15min. 4: 20min. 5: 25min. 6: 30min. 7: 40min. 8: 50min. 9: 60min. 10: 70min. 11: 80min. 12: 90min. 13: 100min. 14: 110min. 15: 120min. 16: 150min. 17: 180min. 18: 210min. 19: 240min. 20: Not used <Default value> The models except e-STUDIO200L: EUR: 7 UC: 9 JPN: 0 Others: 9 e-STUDIO200L: EUR: 7 UC: 6 JPN: 0 Others: 6 0: Black letter on white background 1: White letter on black background 0: TIFF (Multi) 1: PDF
Procedure 1
207
User interface User interface Paper feeding Paper feeding Paper feeding User interface User interface
Highlighting display on LCD Default setting of filing format when E-mailing Paper size (A6-R) feeding/ widthwise direction Tab paper print Tab width setting (Bypass feeding) Tab paper print Shift width setting (Bypass feeding) Default setting of filing format when storing files Language displayed at power-ON
ALL
0 <0-1> 0 <0-1> 148/105 <148432/105297> 130 <100200> 1300 <0-3000> 0 <0-3> EUR: 0 UC: 0 JPN: 5 <0-6>
SYS
209 210
ALL PRT
SYS M
1 10
SYS SYS SYS SYS 0: TIFF (Multi) 1: PDF 2: Not used 3: TIFF (Single) 0: Language 1 1: Language 2 2: Language 3 3: Language 4 4: Language 5 5: Language 6 6: Language 7
1 1 1 1
2 - 57 04/09
Code 221
Setting mode (08) Default Func- <AcceptItems tion able value> Language selection in UI ALL EUR: 0 data at Web power ON UC: 0 JPN: 5 <0-6>
RAM SYS
Contents 0: Language 1 1: Language 2 2: Language 3 3: Language 4 4: Language 5 5: Language 6 6: Language 7 Press the button on the LCD to select the size. Press the button on the LCD to select the size. Press the button on the LCD to select the size. Press the button on the LCD to select the size.
Procedure 1
Paper size for bypass feed Paper size for upper drawer Paper size for lower drawer Paper size for PFP upper drawer
UNDEF EUR: A4 UC: LT JPN: A4 EUR: A3 UC: LD JPN: A3 EUR: A4-R UC: LT-R JPN: A4-R EUR: A4 UC: LG JPN: B4 420/297 <182432/140297> 297/210 <182432/140297> 210/148 <182432/140297> 364/257 <182432/140297> 257/182 <182432/140297> 279/216 <182432/140297> 432/279 <182432/140297> 356/216 <182432/140297>
SYS M M M
9 9 9 9
228 229
Paper feeding Paper feeding Paper feeding Paper feeding Paper feeding Paper feeding Paper feeding Paper feeding Paper feeding
Paper size for PFP lower drawer Paper size (A3) feeding/ widthwise direction Paper size (A4-R) feeding/ widthwise direction Paper size (A5-R) feeding/ widthwise direction Paper size (B4) feeding/ widthwise direction Paper size (B5-R) feeding/ widthwise direction Paper size (LT-R) feeding/ widthwise direction Paper size (LD) feeding/ widthwise direction Paper size (LG) feeding/ widthwise direction
ALL ALL
M M
9 10
230
ALL
10
231
ALL
10
232
ALL
10
233
ALL
10
234
ALL
10
235
ALL
10
236
ALL
10
2 - 58
Code 237
Classification Paper feeding Paper feeding Paper feeding Paper feeding Paper feeding Paper feeding Paper feeding Paper feeding Paper feeding Paper feeding Paper feeding Paper feeding Maintenance
238
239
240
241
242
243
244
245
247
248
249
250
Setting mode (08) Default Func- <AcceptItems tion able value> Paper size (ST-R) feeding/ ALL 216/140 widthwise direction <182432/140297> Paper size (COMPUTER) ALL 356/257 feeding/widthwise direction <182432/140297> Paper size (FOLIO) feedALL 330/210 ing/widthwise direction <182432/140297> Paper size (13 LG) feedALL 330/216 ing/widthwise direction <182432/140297> Paper size (8.5X8.5) ALL 216/216 feeding/widthwise direction <182432/140297> Paper size (Non-standard) ALL 432/279 feeding/widthwise direction <148432/105297> ALL 148/100 Memory 1 <148Paper size (bypass feeding/non-standard type) 432/100297> feeding/widthwise direction Paper size (8K) feeding/ ALL 390/270 widthwise direction <182432/140297> Paper size (16K-R) feedALL 270/195 ing/widthwise direction <182432/140297> Memory 2 ALL 148/100 Paper size (bypass feed<148ing/non-standard type) 432/100feeding/widthwise direction 297> Memory 3 ALL 148/100 Paper size (bypass feed<148ing/non-standard type) 432/100feeding/widthwise direction 297> Memory 4 ALL 148/100 Paper size (bypass feed<148ing/non-standard type) 432/100feeding/widthwise direction 297> Service technician teleALL 0 phone number <32 digits>
RAM M
Contents
Procedure 10
10
10
10
10
SYS
10
SYS
Registers the paper size of bypass feed (non-standard type) into [MEMORY 1].
10
10
10
SYS
SYS
SYS
SYS
Registers the paper size of bypass feed (non-standard type) into [MEMORY 2]. Registers the paper size of bypass feed (non-standard type) into [MEMORY 3]. Registers the paper size of bypass feed (non-standard type) into [MEMORY 4]. A telephone number can be entered up to 32 digits. Use the [Monitor/ Pause] button to enter a hyphen (-).
10
10
10
11
2 - 59
Code 251
Classification Maintenance
Setting mode (08) Default Func- <Accepttion able value> ALL Refer to content <8 digits>
RAM M
Contents <Default> e-STUDIO 230 UC, EUR: 74,000 JPN: 0 e-STUDIO 280 UC, EUR: 90,000 JPN: 0 Counts up when the registration sensor is ON. Displaying of the latest 20 errors data Sets whether the data is printed on the different but similar size paper or not when the paper of corresponding size is not available. 0: Valid (The data is printed on A4/A3 when LT/LD is selected or vice versa.) 1: Invalid (The message to use the selected paper size is displayed.) 0: Automatic 1: PFP single-drawer type installed 2: PFP dual-drawer type installed 3: LCF installed 4: Not installed Press the button on the LCD to select the size. 1) Electrical counter Backup counter 2) Backup counter Electrical counter (P.2-119 "Fig.2-3") Sets whether the FSMS connection is accepted or not. 0: Prohibited 1: Accepted (USB normal connection) 2: Accepted (USB forcible connection) 0: No limits 1 to 30: 1 to 30 days
Procedure 1
Current value of PM counter Display/0 clearing Error history display LT <-> A4/LD <-> A3
M SYS SYS
1 2 1
255
Paper feeding
PFP/LCF installation
ALL
0 <0-4>
256 257
ALL ALL
M -
9 -
258
Maintenance
FSMS acceptance
ALL
1 <0-2>
SYS
259
Network
PRT
14 <0-30>
SYS
2 - 60
Code 260
Classification Network
Setting mode (08) Default Func- <AcceptItems tion able value> Web data retention period SCN 10 <3 digits>
RAM SYS
Contents When a certain period of time has passed without operation after accessing TopAccess, the data being registered is automatically reset. This period is set at this code. (Unit: Minute) Able to enter within 6 digits (Figures only) 0: No limits 1 to 999: 1 to 999 days 2 to 30 M bytes 2 to 30 M bytes Sets the file retention level when editing the files in the Electronic Filing (at CutDoc/SaveDoc command execution). 0: Not full retained 1: Fully retained Retains the source file until CutDoc/ SaveDoc command is completed. * The file is not deleted even if the HDD has become full during the execution of command when 1 is set. Sets the data retention period when creating a user box. 0: Not deleted 1 to 999: Retention period (Unit: Day) Sets the percentage of the HDD capacity filled which warning is displayed 0 to 100: 0 to 100% Sets the days left the notification of E-mail saving time limit appears 0 to 99: 0 to 99 days
Procedure 1
Maximum data capacity at E-mailing Network Maximum data capacity at Internet FAX ElecFull guarantee of docutronic Fil- ments in Electronic Filing ing when HDD is full
11 1 1 1 1
270
ElecDefault value for user box tronic Fil- retention period ing
ALL
0 <0-999>
SYS
271
General
ALL
90 <0-100>
SYS
272
ALL
3 <0-99>
SYS
2 - 61
Code 273
Setting mode (08) Default ClassifiFunc- <AcceptItems cation tion able value> Scanning Default setting of partial ALL 0 <0-6> size when transmitting Email
RAM SYS
Contents Sets the default value for the partial size of Email to be transmitted when creating a template. 0: Not divided 1: 64 2: 128 3: 256 4: 512 5: 1024 6: 2048 (Unit: KB) Sets the default value for the page by page of Internet FAX to be transmitted when creating a template. 0: Not divide 1: 128 2: 512 3: 1024 4: 2048 (Unit: KB) 0: Automatic density 1: Step -5 2: Step -4 3: Step -3 4: Step -2 5: Step -1 6: Step 0 (center) 7: Step +1 8: Step +2 9: Step +3 10: Step +4 11: Step +5 (1 to 11: Manual density) 0: 150 dpi 1: 200 dpi 2: 300 dpi 3: 400dpi 4: 600 dpi 0: Text 1: Text/Photo 2: Photo 0: Single 1: Book 2: Tablet 0: 0 degree 1: 90 degrees 2: 180 degrees 3: 270 degrees 0: Automatic 1: A3 2: A4 3: LD 4: LT 5: A4-R 6: A5-R 7: LT-R 8: LG 9: B4 10: B5 11: ST-R 12: COMP 13: B5-R 14: FOLIO 15: 13LG 16: 8.5 x 8.5 18: A6-R 19: Size mixed 20: 8K 21: 16K 22: 16K-R
Procedure 1
274
FAX
FAX
0 <0-4>
SYS
276
User interface
SCN
0 <0-11>
SYS
User interface User interface User interface User interface User interface
Default setting of resolution Default setting of original mode Default setting of scanning mode Default setting of rotation angle of original Default setting of original paper size
1 1 1 1
286
SCN
SYS
2 - 62
Code 288
Classification General
Setting mode (08) Default Func- <AcceptItems tion able value> Searching interval of deletALL 12 ing expired flies <1-24>
RAM SYS
Contents Sets the search interval of expired files. Deletes if expired file is found. (Unit: Hour) 0: Valid 1: Invalid 0: LD 1: LG 2: LT 3: COMP 4: ST 5: A3 6: A4 7: A5 8: A6 9: B4 10: B5 11: FOLIO 12: 13LG 13: 8.5 x 8.5 0: Plain paper 1: Thick paper 1 2: Thick paper 2 3: Thick paper 3 4: OHP film 0: Portrait 1: Landscape 0: Valid 1: Invalid 0: Inner tray 1: Finisher tray 1 2: Finisher tray 2 3: Not used 4: Job Separator upper tray 5: Job Separator lower tray * The settings 4 and 5 are effective only when the Job Separator (MJ-5004) is installed. Sets the number of form lines from 5 to 128. (A hundredfold of the number of form lines is defined as the setting value.) Sets the font pitch from 0.44 to 99.99. (A hundredfold of the font pitch is defined as the setting value.) Sets the font size from 4 to 999.75. (A hundredfold of the font size is defined as the setting value.) Sets the PCL font number. 0: 999 1: 99 2: 9
Procedure 1
2
1 1
290 291
Network Network
PRT PRT
SYS SYS
292
Network
PRT
0 <0-4>
SYS
Raw printing job (Paper direction) Raw printing job (Staple) Raw printing job (receiving tray)
1 1 1
296
Network
PRT
1200 <50012800>
SYS
297
Network
PRT
SYS
298
Network
PRT
SYS
299 300
Raw printing job (PCL font number) Maximum number of copy volume (MAX9)
PRT PPC
SYS SYS
1 1
2 - 63
Code 302
Setting mode (08) Default Func- <AcceptItems tion able value> Original counter display ALL EUR: 2 UC: 0 JPN: 0 <0,2> Number of A3 output pages A4 in copier func- A5 tion A6 B4 B5 FOLIO LD LG LT ST COMP 13LG 8.5 x 8.5 16K 8K Others Number of A3 output pages A4 in printer func- A5 tion A6 B4 B5 FOLIO LD LG LT ST COMP 13LG 8.5 x 8.5 16K 8K Others PPC 0 <8 digits>
RAM SYS
Contents Sets whether the original counter is displayed or not. 0: Not displayed 2: Displayed Counts the output pages in the copier function for each paper size according to the setting for the count setting of large-sized paper (08-352) and the definition setting of large-sized paper (08353).
Procedure 1
305-0 305-1 305-2 305-3 305-4 305-5 305-6 305-7 305-8 305-9 305-10 305-11 305-12 305-13 305-14 305-15 305-16 306-0 306-1 306-2 306-3 306-4 306-5 306-6 306-7 306-8 306-9 306-10 306-11 306-12 306-13 306-14 306-15 306-16
Counter
SYS
Counter
PRT
0 <8 digits>
SYS
Counts the output pages in the printer function for each paper size according to the setting for the count setting of large-sized paper (08-352) and the definition setting of large-sized paper (08353).
2 - 64
Code 307-0 307-1 307-2 307-3 307-4 307-5 307-6 307-7 307-8 307-9 307-10 307-11 307-12 307-13 307-14 307-15 307-16 308-0 308-1 308-2 308-3 308-4 308-5 308-6 308-7 308-8 308-9 308-10 308-11 308-12 308-13 308-14 308-15 308-16
Classification Counter
Counter
A3 A4 A5 A6 B4 B5 FOLIO LD LG LT ST COMP 13LG 8.5 x 8.5 16K 8K Others A3 A4 A5 A6 B4 B5 FOLIO LD LG LT ST COMP 13LG 8.5 x 8.5 16K 8K Others
Setting mode (08) Default Func- <Accepttion able value> PRT 0 <8 digits>
RAM SYS
Contents Counts the output pages at the list print mode for each paper size according to the setting for the count setting of large-sized paper (08-352) and the definition setting of large-sized paper (08353).
Procedure 4
FAX
0 <8 digits>
SYS
Counts the output pages in the FAX function for each paper size according to the setting for the count setting of large-sized paper (08352) and the definition setting of large-sized paper (08-353).
2 - 65
Code 312-0 312-1 312-2 312-3 312-4 312-5 312-6 312-7 312-8 312-9 312-10 312-11 312-12 312-13 312-14 312-15 312-16 313-0 313-1 313-2 313-3 313-4 313-5 313-6 313-7 313-8 313-9 313-10 313-11 313-12 313-13 313-14 313-15 313-16
Classification Counter
Counter
A3 A4 A5 A6 B4 B5 FOLIO LD LG LT ST COMP 13LG 8.5 x 8.5 16K 8K Others A3 A4 A5 A6 B4 B5 FOLIO LD LG LT ST COMP 13LG 8.5 x 8.5 16K 8K Others
Setting mode (08) Default Func- <Accepttion able value> PPC 0 <8 digits>
RAM SYS
Contents Counts the scanning pages in the copier function for each paper size according to the setting for the count setting of large-sized paper (08-352) and the definition setting of large-sized paper (08353).
Procedure 4
SCN
0 <8 digits>
SYS
Counts the scanning pages in the scanning function for each paper size according to the setting for the count setting of large-sized paper (08-352) and the definition setting of large-sized paper (08353).
2 - 66
Code 314-0 314-1 314-2 314-3 314-4 314-5 314-6 314-7 314-8 314-9 314-10 314-11 314-12 314-13 314-14 314-15 314-16 315-0 315-1 315-2 315-3 315-4 315-5 315-6 315-7 315-8 315-9 315-10 315-11 315-12 315-13 315-14 315-15 315-16
Classification Counter
Counter
A3 A4 A5 A6 B4 B5 FOLIO LD LG LT ST COMP 13LG 8.5 x 8.5 16K 8K Others A3 A4 A5 A6 B4 B5 FOLIO LD LG LT ST COMP 13LG 8.5 x 8.5 16K 8K Others
Setting mode (08) Default Func- <Accepttion able value> FAX 0 <8 digits>
RAM SYS
Contents Counts the scanning pages in the FAX function for each paper size according to the setting for the count setting of large-sized paper (08352) and the definition setting of large-sized paper (08-353).
Procedure 4
FAX
0 <8 digits>
SYS
Counts the transmitted pages in the FAX function for each paper size according to the setting for the count setting of large-sized paper (08352) and the definition setting of large-sized paper (08-353).
2 - 67
Code 316-0 316-1 316-2 316-3 316-4 316-5 316-6 316-7 316-8 316-9 316-10 316-11 316-12 316-13 316-14 316-15 316-16 320-0
Classification Counter
Counter
Setting mode (08) Default Func- <Accepttion able value> FAX 0 <8 digits>
RAM SYS
Contents Counts the received pages in the FAX function for each paper size according to the setting for the count setting of large-sized paper (08352) and the definition setting of large-sized paper (08-353).
Procedure 4
PPC
0 <8 digits>
SYS
320-1
Counter
Small
PPC
0 <8 digits>
SYS
320-2
Counter
Total
PPC
0 <8 digits>
SYS
321-0
Counter
PRT
0 <8 digits>
SYS
321-1
Counter
PRT
0 <8 digits>
SYS
321-2
Counter
Total
PRT
0 <8 digits>
SYS
Counts the number of output pages in the Copier Function according to its size (large/small). Large: Number of output pages of large-sized paper defined at 08353 Small: Number of output pages other than set as large-sized paper Total: Total number output pages of all paper sizes. Counts the number of output pages in the Printer Function according to its size (large/small). Large: Number of output pages of large-sized paper defined at 08353 Small: Number of output pages other than set as large-sized paper Total: Total number output pages of all paper sizes.
14
14
14
14
14
14
2 - 68
Code 322-0
Classification Counter
Setting mode (08) Default Func- <Accepttion able value> PRT 0 <8 digits>
RAM SYS
Contents Counts the number of output pages at the List Print Mode Function according to its size (large/small). Large: Number of output pages of large-sized paper defined at 08353 Small: Number of output pages other than set as large-sized paper Total: Total number output pages of all paper sizes. Counts the number of output pages in the FAX Function according to its size (large/small). Large: Number of output pages of large-sized paper defined at 08353 Small: Number of output pages other than set as large-sized paper Total: Total number output pages of all paper sizes. Counts the number of scanning pages in the Copier Function according to its size (large/small). Large: Number of output pages of large-sized paper defined at 08353 Small: Number of output pages other than set as large-sized paper Total: Total number output pages of all paper sizes.
Procedure 14
2
14
322-1
Counter
Small
PRT
0 <8 digits>
SYS
322-2
Counter
Total
PRT
0 <8 digits>
SYS
14
323-0
Counter
Large
PRT
0 <8 digits>
SYS
14
323-1
Counter
Small
PRT
0 <8 digits>
SYS
14
323-2
Counter
Total
PRT
0 <8 digits>
SYS
14
327-0
Counter
Large
PPC
0 <8 digits>
SYS
14
327-1
Counter
Small
PPC
0 <8 digits>
SYS
14
327-2
Counter
Total
PPC
0 <8 digits>
SYS
14
2 - 69
Code 328-0
Classification Counter
Setting mode (08) Default Func- <Accepttion able value> FAX 0 <8 digits>
RAM SYS
Contents Counts the number of scanning pages in the FAX Function according to its size (large/small). Large: Number of output pages of large-sized paper defined at 08353 Small: Number of output pages other than set as large-sized paper Total: Total number output pages of all paper sizes. Counts the number of scanning pages in the Scanning Function according to its size (large/small). Large: Number of output pages of large-sized paper defined at 08353 Small: Number of output pages other than set as large-sized paper Total: Total number output pages of all paper sizes. Counts the number of transmitted pages in the FAX Function according to its size (large/small). Large: Number of output pages of large-sized paper defined at 08353 Small: Number of output pages other than set as large-sized paper Total: Total number output pages of all paper sizes.
Procedure 14
328-1
Counter
Small
FAX
0 <8 digits>
SYS
14
328-2
Counter
Total
FAX
0 <8 digits>
SYS
14
329-0
Counter
Large
SCN
0 <8 digits>
SYS
14
329-1
Counter
Small
SCN
0 <8 digits>
SYS
14
329-2
Counter
Total
SCN
0 <8 digits>
SYS
14
330-0
Counter
Large
FAX
0 <8 digits>
SYS
14
330-1
Counter
Small
FAX
0 <8 digits>
SYS
14
330-2
Counter
Total
FAX
0 <8 digits>
SYS
14
2 - 70
Code 331
Setting mode (08) Default Func- <AcceptItems tion able value> Default setting of screen ALL 0 <0-3>
RAM SYS
Contents Sets the screen to be displayed after the auto-clear time has passed or it has recovered from the energy saving mode or sleep mode. 0: Copier 1: Fax 2: Scan 3: Box Counts the number of received pages in the FAX Function according to its size (large/small). Large: Number of output pages of large-sized paper defined at 08353 Small: Number of output pages other than set as large-sized paper Total: Total number output pages of all paper sizes. Displays the total number of pages in the copier/printer/scanning/ FAX functions.
Procedure 1
332-0
Counter
Large
FAX
0 <8 digits>
SYS
14
332-1
Counter
Small
FAX
0 <8 digits>
SYS
14
332-2
Counter
Total
FAX
0 <8 digits>
SYS
14
Counter Counter Counter Paper feeding Paper feeding Paper feeding Paper feeding Paper feeding Counter Counter
Paper size (#10-R) feeding/widthwise direction Paper size (DL-R) feeding/widthwise direction Paper size (Envelope: Monarch-R) feeding/widthwise direction Paper size (Envelope: CHO-3-R) feeding/widthwise direction Paper size (Envelope: YOU-4-R) feeding/widthwise direction Count setting of envelope (PM) Count setting of largesized paper (PM)
338
ALL
339
ALL
340
ALL
341
ALL
345 346
ALL ALL
0 <8 digits> 0 <8 digits> 0 <8 digits> 241/105 <148432/105297> 220/110 <148432/105297> 191/98 <148432/98297> 235/120 <148432/105297> 235/105 <148432/105297> 1 <0-1> 1 <0-1>
14 14 14 10
10
10
10
10
M M
1 1
2 - 71
Setting mode (08) Default Func- <AcceptItems tion able value> Definition setting of largeALL 1 sized paper (PM) <0-1> Count setting of thick paper (PM) Count setting of OHP film (PM) Count setting of largesized paper (Fee charging system counter) Definition setting of largesized paper (Fee charging system counter) Counter for upper drawer feeding Counter for lower drawer feeding Counter for bypass feeding Counter for LCF feeding Counter for PFP upper drawer feeding Counter for PFP lower drawer feeding Counter for ADU Counter for RADF Setting for counter installed externally ALL ALL ALL 1 <0-1> 1 <0-1> JPN: 0 OTHER: 1 <0-2> 0 <0-1> 0 <8 digits> 0 <8 digits> 0 <8 digits> 0 <8 digits> 0 <8 digits> 0 <8 digits> 0 <8 digits> 0 <8 digits> 1 <0-7>
RAM M M M M
Contents 0: A3/LD 1: A3/LD/B4/LG/ FOLIO/COMP 0: Counted as 1 1: Counted as 2 0: Counted as 1 1: Counted as 2 0: Counted as 1 1: Counted as 2 2: Counted as 1 (Mechanical counter is double counter) 0: A3/LD 1: A3/LD/B4/LG/ FOLIO/COMP/8K Counts the number of sheets fed from upper drawer Counts the number of sheets fed from lower drawer Counts the number of sheets fed from bypass feed Counts the number of sheets fed from LCF Counts the number of sheets fed from PFP upper drawer Counts the number of sheets fed from PFP lower drawer Counts the number of output pages of duplex printing. Counts the number of originals fed from RADF Selects the job to count up for the external counter. 0: Not selected 1: Copier 2: FAX 3: Copier/FAX 4: Printer 5: Copier/Printer 6: Printer/FAX 7: Copier/Printer/FAX The number of error is reset at HDD formatting. The number of error is reset at HDD formatting. The number of error is reset at HDD formatting.
Procedure 1 1 1 1
353
Counter
ALL
M M M M M M M SYS M
2 2 2 2 2 2 2 2 1
Number of errors in HDD (Copier) Number of errors in HDD (FAX) Number of errors in HDD (Scanning)
2 2 2
2 - 72
Setting mode (08) Default Func- <AcceptItems tion able value> Number of errors in HDD PRT 0 (Printer) <8 digits> Number of polygonal motor rotational speed switching ALL 0 <8 digits>
RAM SYS M
Contents The number of error is reset at HDD formatting. Counts the number of time the polygonal motor has switched its rotational speed between normal rotation and standby rotation. Accumulates the time the polygonal motor has rotated at normal rotation. 0: No error 1: C410 (Once) 2: C410 (consecutively occurred) 3: 4: 5: C440 6: C450 7: C440 8: C450 9: C440 10: C470 11: C470 12: C480 13: C490 14: C470 15: C480 16: C490 17: C470 18: C480 19: C490 This code is valid only when 20 is set to 08886. Setting value x -5C: from 0C to -50C
Procedure 2 2
399
Laser
Accumulated time of polygonal motor at normal rotation Fuser unit error status counter
ALL
400
Fuser
ALL
Fuser
Fuser
Fuser
The first drop The second drop The third drop The fourth drop The first Temperature drop setting in drop ready status The sec(Side therond drop mistor) The third drop The fourth drop Fuser roller temperature in ready status (Side thermistor)
M M M M M M M M M
4 4 4 4 4 4 4 4
0: 140C 1: 145C 2: 150C 3: 155C 4: 160C 5: 165C 6: 170C 7: 175C 8: 180C 9: 185C 10: 190C 11: 195C 12: 200C
2 - 73 04/09
Code 409
Classification Fuser
Setting mode (08) Default Func- <AcceptItems tion able value> Fuser roller temperature at ALL 0 <0-13> energy saver mode (Center thermistor)
RAM M
Contents 0: OFF 1: 40C 2: 50C 3: 60C 4: 70C 5: 80C 6: 90C 7: 100C 8: 110C 9: 120C 10: 130C 11: 140C 12: 150C 13: 160C 0: 140C 1: 145C 2: 150C 3: 155C 4: 160C 5: 165C 6: 170C 7: 175C 8: 180C 9: 185C 10: 190C 11: 195C 12: 200C 13: 205C 14: 210C 0: 140C 1: 145C 2: 150C 3: 155C 4: 160C 5: 165C 6: 170C 7: 175C 8: 180C 9: 185C 10: 190C 11: 195C 12: 200C 0: 140C 1: 145C 2: 150C 3: 155C 4: 160C 5: 165C 6: 170C 7: 175C 8: 180C 9: 185C 10: 190C 11: 195C 12: 200C 13: 205C 14: 210C 0: 140C 1: 145C 2: 150C 3: 155C 4: 160C 5: 165C 6: 170C 7: 175C 8: 180C 9: 185C 10: 190C 11: 195C 12: 200C 13: 205C 14: 210C
Procedure 1
410
Fuser
ALL
8 <0-14>
411
Fuser
ALL
8 <0-12>
412
Fuser
ALL
9 <0-14>
413
Fuser
ALL
8 <0-14>
2 - 74
Code 414
Classification Developer
Setting mode (08) Default Func- <AcceptItems tion able value> Toner density life correcALL 0 tion switching <0-7>
RAM M
Contents 0: Unchanged (Default) 1: Approx. 0.3 wt% higher 2: Approx. 0.6 wt% higher 3: Approx. 0.9 wt% higher 4: Approx. 0.2 wt% lower 5: Approx. 0.4 wt% lower 6: Approx. 0.6 wt% lower 7: Approx. 0.9 wt% lower 0: Invalid 1: 1 sec. 2: 2 sec. 3: 3 sec. 4: 4 sec. 5: 5 sec. 6: 6 sec. 7: 7 sec. 8: 8 sec. 9: 9 sec. 10: 10 sec. 11: 12 sec. 12: 14 sec. 13: 16 sec. 14: 18 sec. 15: 20 sec. This code is valid only when 20 is set to 08886. Setting value x 1 min.: from 2 to 60 min. later
Procedure 1
417
Fuser
ALL
10 <0-15>
Fuser
Fuser
Fuser
433-1
The first drop The second drop The third drop The fourth drop The first drop The second drop The third drop The fourth drop Center thermistor Side thermistor
15 <2-60> 15 <2-60> 15 <2-60> 15 <2-60> 15 <2-60> 15 <2-60> 15 <2-60> 15 <2-60> 7 <0-12> 5 <0-12>
M M M M M M M M M
4 4 4 4 4 4 4 4
ALL
0: 130C 1: 135C 2: 140C 3: 145C 4: 150C 5: 155C 6: 160C 7: 165C 8: 170C 9: 175C 10: 180C 11: 185C 12: 120C
2 - 75 04/09
Code 437
Classification Fuser
Setting mode (08) Default Func- <AcceptItems tion able value> Fuser roller temperature ALL 8 <0-14> during printing (Center thermistor /Thick paper 2)
RAM M
Contents 0: 140C 1: 145C 2: 150C 3: 155C 4: 160C 5: 165C 6: 170C 7: 175C 8: 180C 9: 185C 10: 190C 11: 195C 12: 200C 13: 205C 14: 210C 0: 140C 1: 145C 2: 150C 3: 155C 4: 160C 5: 165C 6: 170C 7: 175C 8: 180C 9: 185C 10: 190C 11: 195C 12: 200C 13: 205C 14: 210C 0: Invalid 1: 1 sec. 2: 2 sec. 3: 3 sec. 4: 4 sec. 5: 5 sec. 6: 6 sec. 7: 7 sec. 8: 8 sec. 9: 9 sec. 10: 10 sec. 11: 12 sec. 12: 14 sec. 13: 16 sec. 14: 18 sec. 15: 20 sec. 0: Invalid 1: 1 sec. 2: 2 sec. 3: 3 sec. 4: 4 sec. 5: 5 sec. 6: 6 sec. 7: 7 sec. 8: 8 sec. 9: 9 sec. 10: 10 sec. 11: 12 sec. 12: 14 sec. 13: 16 sec. 14: 18 sec. 15: 20 sec. 0: Invalid 1: 1 sec. 2: 2 sec. 3: 3 sec. 4: 4 sec. 5: 5 sec. 6: 6 sec. 7: 7 sec. 8: 8 sec. 9: 9 sec. 10: 10 sec. 11: 12 sec. 12: 14 sec. 13: 16 sec. 14: 18 sec. 15: 20 sec.
Procedure 1
438
Fuser
ALL
8 <0-14>
439
Fuser
ALL
10 <0-15>
440
Fuser
ALL
0 <0-15>
441
Fuser
ALL
0 <0-15>
2 - 76
Code 448
Classification Fuser
Setting mode (08) Default Func- <AcceptItems tion able value> Fuser roller temperature in ALL 0 <0-13> Energy Saving Mode (Side thermistor)
RAM M
Contents 0: OFF 1: 40C 2: 50C 3: 60C 4: 70C 5: 80C 6: 90C 7: 100C 8: 110C 9: 120C 10: 130C 11: 140C 12: 150C 13: 160C 0: 140C 1: 145C 2: 150C 3: 155C 4: 160C 5: 165C 6: 170C 7: 175C 8: 180C 9: 185C 10: 190C 11: 195C 12: 200C 13: 205C 14: 210C 0: 140C 1: 145C 2: 150C 3: 155C 4: 160C 5: 165C 6: 170C 7: 175C 8: 180C 9: 185C 10: 190C 11: 195C 12: 200C 13: 205C 14: 210C 0: 140C 1: 145C 2: 150C 3: 155C 4: 160C 5: 165C 6: 170C 7: 175C 8: 180C 9: 185C 10: 190C 11: 195C 12: 200C 13: 205C 14: 210C 0: 140C 1: 145C 2: 150C 3: 155C 4: 160C 5: 165C 6: 170C 7: 175C 8: 180C 9: 185C 10: 190C 11: 195C 12: 200C 13: 205C 14: 210C Corrects the supply amount of the fresh toner (driving period of the toner motor) into the developer unit. 0: x1.0 1: x0.75 2: x0.5 3: x0.3 4: x2.0 5: x1.5
Procedure 1
450
Fuser
ALL
8 <0-14>
451
Fuser
ALL
8 <0-14>
452
Fuser
ALL
8 <0-14>
453
Fuser
ALL
8 <0-14>
455
Image processing
ALL
0 <0-5>
2 - 77
Code 462
Classification RADF
Setting mode (08) Default Func- <AcceptItems tion able value> Setting for switchback ALL 0 <0-1> operation to copy mixedsized original on RADF
RAM M
Contents Sets whether or not detecting the original length by transporting without scanning in reverse when finding A4-R/FOLIO paper. 0: Invalid- Judges as A4-R without transporting in reverse with no scanning. 1: Valid- Judges whether it is A4-R or FOLIO size by transporting in reverse with no scanning. * The original is transported in reverse with no scanning when detecting LTLG size-paper in LT, regardless of this setting. Sets the number of times of the feeding retry from the upper drawer. Sets the number of times of the feeding retry from the lower drawer. Sets the number of times of the feeding retry from the PFP upper drawer. Sets the number of times of the feeding retry from the PFP lower drawer. Sets the number of times of the feeding retry from the bypass tray. Sets the number of times of the feeding retry from the LCF. * Postcard is supported only for JPN model.
Procedure 1
463-0 463-1 464-0 464-1 465-0 465-1 466-0 466-1 467-0 467-1 468-0 468-1 471
Paper feeding
Paper feeding
Feeding retry number setting (upper drawer) Feeding retry number setting (lower drawer) Feeding retry number setting (PFP upper drawer) Feeding retry number setting (PFP lower drawer) Feeding retry number setting (bypass feed) Feeding retry number setting (LCF)
Plain paper Others Plain paper Others Plain paper Others Plain paper Others Plain paper Others Plain paper Others
ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL
5 <0-5> 5 <0-5> 5 <0-5> 5 <0-5> 5 <0-5> 5 <0-5> 5 <0-5> 5 <0-5> 5 <0-5> 5 <0-5> 5 <0-5> 5 <0-5> 148/100 <148432/100297>
M M M M M M M M M M M M M
4 4 4 4 4 4 4 4 4 4 4 4 10
Paper feeding
Paper feeding
Paper feeding
Paper feeding
Paper feeding
2 - 78
Code 477
Classification General
Setting mode (08) Default Func- <Accepttion able value> ALL Refer to content <0-1> ALL 0 <0-1>
RAM M
Contents <Default value> Lower drawer reference: 0 Upper drawer reference: 1 Displays the error [CA10] when the set number of rotation error has been detected. 0: 2 times 1: 12 times 0: Waiting time for polygonal motor rotation overshooting 0.6 sec. 1: Waiting time for polygonal motor rotation overshooting 2.2 sec. 0: A4/LT 1: LCF 2: Upper drawer 3: Lower drawer 4: PFP upper drawer 5: PFP lower drawer Sets whether or not changing the drawer automatically to the other drawer with the paper of the same size when paper in the selected drawer has run out. 0: OFF 1: ON (Changes to the drawer with the same paper direction and size: ex. A4 to A4) 2: ON (Changes to the drawer with the same paper size. Paper with the different direction is acceptable as long as the size is the same: ex., A4 to A4R, LT-R to LT. 1 is applied when the staple/hole-punch is specified.) 0: ON 1: OFF
Procedure 2
2
1
478
Laser
Judged number of polygonal motor rotation error (Normal rotation) Judged number of polygonal motor rotation error (At acceleration/deceleration)
479
Laser
ALL
0 <0-1>
480
Paper feeding
ALL
0 <0-5>
481
Paper feeding
PPC
1 <0-2>
SYS
482
Paper feeding
ALL
0 <0-1>
2 - 79 04/09
Code 483
Classification Laser
Setting mode (08) Default Func- <Accepttion able value> ALL 0 <0-2>
RAM SYS
Contents Sets whether or not switching the polygonal motor from the standby rotation to the normal rotation when the original is set on the RADF or the platen cover is opened. 0: Valid (when using RADF and the original is set manually) 1: Invalid 2: Valid (when using RADF only) Sets whether or not switching the polygonal motor from the normal rotation to the standby rotation at the Auto Clear Mode. 0: Valid 1: Invalid Sets the rotational status of polygonal motor on standby. 0: Rotated (The rotational speed is set at 08-490.) 1: Stopped Switches the polygonal motor to the standby rotation when a certain period of time has passed from the prerunning. At this code, the period to switch the status to the standby rotation is set. 0: 15 sec.1: 30 sec. 2: 45 sec. * This setting is effective when 0 or 2 is set at 08-483. Set the type of polygonal motor. 0: 2-clock type 1: 3-clock type 2: 4-clock type 3: 4-clock type 0: 38,090.55 rpm 1: 35,000 rpm 2: 30,000 rpm 3: 25,000 rpm 4: 20,000 rpm 5: 10,000 rpm 0: Stopped 1: 10,000 rpm
Procedure 1
484
Laser
ALL
0 <0-1>
SYS
485
Laser
ALL
SYS
486
Laser
ALL
0 <0-2>
SYS
488
Laser
ALL
0 <0-3>
489
Laser
ALL
5 <0-5>
490
Laser
ALL
0 <0-1>
2 - 80 04/09
Code 491
Classification Transfer
Setting mode (08) Default Func- <AcceptItems tion able value> Transfer charger bias corALL 149 rection (H) at duplexing <0-255>
RAM M
Contents Corrects the transfer charger bias output value of the leading edge area of paper at duplexing. Corrects the transfer charger bias output value of the center area of paper at duplexing. Corrects the transfer charger bias output value of the trailing edge area of paper at duplexing. Sets the image reproduction method at photo mode. 0: Error diffusion 1: Dither 0: Automatic 1: Manual (Center) 0: Not used 1: Custom Mode 1 when Text/Photo is set as a base 2: Custom Mode 2 when Text is set as a base 3: Custom Mode 3 when Photo is set as a base Switches the image processing method when Custom Mode 3 is set. 0: Error diffusion 1: Dither 0: 140C 1: 145C 2: 150C 3: 155C 4: 160C 5: 165C 6: 170C 7: 175C 8: 180C 9: 185C 10: 190C 11: 195C 12: 200C 13: 205C 14: 210C 0: 140C 1: 145C 2: 150C 3: 155C 4: 160C 5: 165C 6: 170C 7: 175C 8: 180C 9: 185C 10: 190C 11: 195C 12: 200C 13: 205C 14: 210C
Procedure 1
2
1
492
Transfer
Transfer charger bias correction (C) at duplexing Transfer charger bias correction (L) at duplexing
ALL
493
Transfer
ALL
502
Image
PPC
1 <0-1>
SYS
503 508
PPC PPC
0 <0-1> 0 <0-3>
SYS SYS
1 1
509
Image
PPC
1 <0-1>
SYS
515
Fuser
ALL
9 <0-14>
516
Fuser
ALL
9 <0-14>
2 - 81
Code 518
Classification Fuser
Setting mode (08) Default Func- <AcceptItems tion able value> Fuser roller temperature ALL 9 <0-14> during printing (Side thermistor/Thick paper 3)
RAM M
Contents 0: 140C 1: 145C 2: 150C 3: 155C 4: 160C 5: 165C 6: 170C 7: 175C 8: 180C 9: 185C 10: 190C 11: 195C 12: 200C 13: 205C 14: 210C 0: 140C 1: 145C 2: 150C 3: 155C 4: 160C 5: 165C 6: 170C 7: 175C 8: 180C 9: 185C 10: 190C 11: 195C 12: 200C 13: 205C 14: 210C 0: 140C 1: 145C 2: 150C 3: 155C 4: 160C 5: 165C 6: 170C 7: 175C 8: 180C 9: 185C 10: 190C 11: 195C 12: 200C 13: 205C 14: 210C 0: Invalid 1: 1 sec. 2: 2 sec. 3: 3 sec. 4: 4 sec. 5: 5 sec. 6: 6 sec. 7: 7 sec. 8: 8 sec. 9: 9 sec. 10: 10 sec. 11: 12 sec. 12: 14 sec. 13: 16 sec. 14: 18 sec. 15: 20 sec. This code is valid only when 20 is set to 08535. Setting value x 5 sec.: from 0 to 1,000 sec. later
Procedure 1
520
Fuser
ALL
9 <0-14>
521
Fuser
ALL
9 <0-14>
523
Fuser
ALL
10 <0-15>
Fuser
The first drop The second drop The third drop The fourth drop
M M M M
4 4 4 4
2 - 82 04/09
Code 526
Classification Fuser
Setting mode (08) Default Func- <AcceptItems tion able value> Pre-running time for first ALL 0 printing (OHP film) <0-15>
RAM M
Contents 0: Invalid 1: 0 sec. 2: 2 sec. 3: 3 sec. 4: 4 sec. 5: 5 sec. 6: 6 sec. 7: 7 sec. 8: 8 sec. 9: 9 sec. 10: 10 sec. 11: 12 sec. 12: 14 sec. 13: 16 sec. 14: 18 sec. 15: 20 sec. This code is valid only when 20 is set to 08535. Setting value x 5 sec.: from 0 to 1,000 sec. later
Procedure 1
Fuser
Fuser
The first drop The second drop The third drop The fourth drop Temperature drop control setting during printing (Temperature/Time)
M M M M M
4 4 4 4
Fuser
Fuser
The first drop The second drop The third drop The fourth drop Temperature The first drop setting drop during printing The sec(Side therond drop mistor) The third drop The fourth drop
M M M M M M M M
0: None 1: Pattern 1 2: Pattern 2 3: Pattern 3 4: Pattern 4 5: Pattern 5 6: Pattern 6 7: Pattern 7 8: Pattern 8 9: Pattern 9 10: Pattern 10 11: Pattern 11 12: Pattern 12 13: Pattern 13 14: Pattern 14 15: Pattern 15 16: Pattern 16 17: Pattern 17 18: Pattern 18 19: Pattern 19 20: Manual adjustment This code is valid only when 20 is set to 08535. Setting value x -5C: from 0C to -50C
4 4 4 4 4 4 4 4
2 - 83 04/09
Setting mode (08) Default Func- <AcceptItems tion able value> Default setting of original PPC 0 mode <0-10> Setting for the Energy Saving Mode ALL Refer to content <0-1>
Contents 0: Text/Photo 1: Photo 2: Text 3: Custom Mode 0: Auto Shut Off Mode 1: Sleep Mode <Default value> The models except e-STUDIO200L: EUR, UC, SAD: 1 JPN, Others: 0 e-STUDIO200L: EUR, SAD: 1 UC, JPN, Others: 0 0: OFF 1: ON
Procedure 1 1
602
Screen setting for Auto power Save Mode and Auto Shut OFF Mode Setting for automatic duplexing mode
ALL
603
PPC
SYS
SYS
604
User interface
PPC
0 <0-2>
SYS
605 607
PPC PPC
0 <0-1> 0 <0-1>
SYS SYS
0: Invalid 1: Single-sided to duplex copying 2: Double-sided to duplex copying 3: User selection 0: APS (Automatic Paper Selection) 1: AMS (Automatic Magnification Selection) 2: Not selected 0: Invalid 1: Valid 0: Continuous feeding (by pressing the [START] button) 1: Single feeding (by setting original on the tray) 0: OFF 1: ON 0: Left page to right page 1: Right page to left page 0: Not summer time 1: Summer time Press the button on the LCD to select the size.
1 1
610 611
ALL PPC
SYS SYS
1 1
612 613
ALL PPC
SYS SYS
1 9
2 - 84 04/09
Code 614
Classification Network
Setting mode (08) Default Func- <AcceptItems tion able value> Local I/F time-out period PRT 6 <1-50>
RAM SYS
Contents Sets the period of time when the job is judged as completed in local I/ F printing (USB or parallel). 1: 1.0 sec. 2: 1.5 sec. -50: 25.5 sec. (in increments of 0.5 sec.) Displays the sizes of the main memory and page memory. Enables to check if each memory is properly recognized. 0: Printed 1: Not printed 0: Scanned as all in same size 1: Scanned as each original size Sets the time taken to add paper feeding when paper in the bypass tray has run out during the bypass feed copying. 0: Paper is not drawn in unless the [START] button is pressed. 1-10: Setting value x 0.5 sec. 0: Invalid 1: Valid 0: Invalid 1: Valid 0: Invalid 1: Valid 0: Invalid 1: Valid 0: Invalid 1: Valid 0: OFF 1: ON (Start printing when the scanning of each page is finished) 0: Not rotating 1: Rotating 0: Automatic 1: Portrait 0: Invalid 1: Valid 0: Normal 1: Inner receiving tray
Procedure 1
615
General
ALL
SYS
617 618
Print setting without department code Default setting when mixed size originals are set on RADF Time lag before Auto Job Start of bypass feeding
ALL PPC
SYS SYS
1 1
619
ALL
SYS
User interface User interface User interface User interface User interface User interface
Department management setting (Copier) Department management setting (FAX) Department management setting (Printer) Department management setting (Scanner) Department management setting (List print) Blank copying prevention mode during RADF jamming Rotation printing at the non-sorting Direction priority of original image Department management setting Inner receiving tray priority at Non-sort Mode
1 1 1 1 1 1
1 1 1 1
2 - 85
Setting mode (08) Default Func- <AcceptItems tion able value> Width setting for image PPC 0 <0-1> shift copying (linkage of front side and back side) Time differences ALL EUR: 24 UC: 40 JPN: 6 <0-47>
Contents
Procedure 1 1
640
ALL
641 642
Automatic Sorting Mode setting (RADF) Default setting of Sorter Mode Correction of reproduction ratio in editing copy
PPC PPC
SYS
0: +12.0h 1: +11.5h 2: +11.0h 3: +10.5h 4: +10.0h 5: +9.5h 6: +9.0h 7: +8.5h 8: +8.0h 9: +7.5h 10: +7.0h 11: +6.5h 12: +6.0h 13: +5.5h 14: +5.0h 15: +4.5h 16: +4.0h 17: +3.5h 18: +3.0h 19: +2.5h 20: +2.0h 21: +1.5h 22: +1.0h 23: +0.5h 24: 0.0h 25: -0.5h 26: -1.0h 27: -1.5h 28: -2.0h 29: -2.5h 30: -3.0h 31: -3.5h 32: -4.0h 33: -4.5h 34: -5.0h 35: -5.5h 36: -6.0h 37: -6.5h 38: -7.0h 39: -7.5h 40: -8.0h 41: -8.5h 42: -9.0h 43: -9.5h 44: -10.0h 45: -10.5h 46: -11.0h 47: -11.5h 0: YYYY.MM.DD. 1: DD.MM.YYYY 2: MM.DD.YYYY 0: Invalid 1: STAPLE 2: SORT 3: GROUP 4: ROTATE SORT 0: NON-SORT 1: STAPLE 2: SORT 3: GROUP 4: ROTATE SORT Sets the reproduction ratio for the X in 1 printing (including magazine sort) to the Reproduction ratio x Correction ratio. 0: 90% 1: 91% 2: 92% 3: 93% 4: 94% 5: 95% 6: 96% 7: 97% 8: 98% 9: 99% 10: 100% Sets the page pasted position for X in 1 to the upper left corner/ center. 0: Cornering 1: Centering
SYS SYS
1 1
645
PPC
SYS
646
User interface
PPC
0 <0-1>
SYS
2 - 86
Setting mode (08) Default Func- <AcceptItems tion able value> Rotation of paper direction ALL 1 for BOX printing <0-1> Returning finisher tray ALL 0 when printing is finished <0-1>
Contents 0: Rotation OFF 1: Rotation ON Sets whether or not returning the finisher tray to the bin 1 when printing is finished. 0: Not returned 1: Returned 0: Left page to right page 1: Right page to left page 0: Horizontal 1: Vertical Hyphen (with page number) /Dropout (with date, time and page number) 0: OFF/OFF 1: ON/OFF 2: OFF/ON 3: ON/ON Note: Note: Hyphen printing format ON: -1- OFF: 1 0: OFF 1: ON 0: OFF 1: ON
Procedure 1 1
649
PPC
SYS
650 651
2 in 1/4 in 1 page allocating order setting Printing format setting for Time stamp and Page Number
PPC PPC
SYS SYS
1 1
Cascade operation setting Cascade operation setting Direction priority for date and time stamp printing Auto Job Start setting for bypass feed printing
1 1 1 1
659
User interface
PPC
1 <0-1>
SYS
660 661
Network Network
ALL ALL
0 <0-1> 0 <0-1>
SYS SYS
0: Short edge 1: Long edge Sets whether or not feeding a paper automatically into the equipment when it is placed on the bypass tray. 0: OFF (Press the [START] button to start feeding.) 1: ON (Automatic feeding) Sets whether or not feeding a paper automatically into the equipment when it is placed on the bypass tray. 0: OFF (Press the [START] button to start feeding.) 1: ON (Automatic feeding) 0: Invalid 1: Valid 0: Invalid 1: Valid
1 1
2 - 87
Code 662
Classification General
Setting mode (08) Default Func- <AcceptItems tion able value> Clearing of SMS partition ALL -
RAM SYS
Contents Clears SMS partition. (Performs when the service call [F106] has occurred.) Initializes the Electronic Filing. Initializes the shared folder. Display the HDD information 0: Invalid 1: Valid Initializing of the department management information * Key in the code and press the [INITIALIZE] button to perform the initialization. If the area storing the department management information is destroyed for some reason, Enter Department Code is displayed on the control panel even if the department management function is not set on. In this case, initialize the area with this code. This area is normally initialized at the factory. Sets the trial period from 1 to 60 days. This setting is effective only when the default value is 254. Once the default value is set, this value is only used for a reference. Sets whether or not displaying the banner advertising. The setting contents of 08-679 and 08-680 are displayed at the time display section on the right top of the screen. When both are set, each content is displayed alternately. 0: Not displayed 1: Displayed Maximum 27 letters (one-byte character)
Procedure 3
/SHR partition clearing /SHA partition clearing HDD diagnostic menu display Size indicator Initialization of department management information
0 <0-1> -
3 3 2 1 3
673
General
PRT/ SCN
254 <1-60>
SYS
678
General
ALL
0 <0-1>
SYS
679
General
ALL
SYS
11
2 - 88 04/09
Setting mode (08) Default Func- <AcceptItems tion able value> Banner advertising display ALL 2 Display of [BANNER MESALL 0 SAGE] button <0-1>
Contents Maximum 27 letters (one-byte character) 0: Not displayed 1: Displayed * This button enables the entry of Banner advertising display 1 (08-679) and Banner advertising display 2 (08-680) on the control panel. 0: Invalid 1: Valid When the duplex printing is short paid with a coin controller, reverse side of the original is not printed and is considered as a defect (printing job may be cleared). To solve this problem, the selection of printing method is enabled with this setting. 0: Invalid (Both sides printed) 1: Valid (Only one side printed) Rebuilds all databases. Rebuilds all databases related to the Address Book. Rebuilds all databases related to the log. 0: Not subjected for APS judgment 1: Subjected for APS judgment 2: Normal formatting 0: Not formatted 1: Not used 2: Normal format Performs the calibration of the pressing position on the touch panel (LCD screen). The calibration is performed by pressing 2 reference positions after this code is started up. Returns the value to the factory shipping default value. Checks the bad sector.
Procedure 11 1
682 683
Offsetting between jobs Duplex printing setting when coin controller is used
ALL ALL
0 <0-1> 1 <0-1>
SYS SYS
1 1
Rebuilding all databases Rebuilding all databases related to address book Rebuilding all databases related to log Adaptation of paper source priority selection HDD formatting HDD type display Performing panel calibration
3 3 3 1
7 7 1
693 694
General General
ALL ALL
SYS SYS
3 3
2 - 89
Code 695
Classification General
Setting mode (08) Default Func- <AcceptItems tion able value> Notifying condition of trial PRT/ 3 period end SCN <0-59> Installation of scrambler board (Option) Paper type priority ALL PPC 0 <0-1> 1 <1-2> EUR: 5 UC: 4 JPN: 0 Other: 1 <0-25>
RAM SYS
Contents Sets when the end of trial period is notified. 0: On the day it ends 1 to 59: n days before 0: Not installed 1: Installed Sets the paper type priority during copying. 1: Plain paper 2: Thick paper 1 Start up this code and have the user enter the key code. This setting is effective only when the scrambler board is installed. 0: Japan 1: Asia 2: Australia 3: Hong Kong 4: U.S.A./Canada 5: Germany 6: U.K. 7: Italy 8: Belgium 9: Netherlands 10: Finland 11: Spain 12: Austria 13: Switzerland 14: Sweden 15: Denmark 16: Norway 17: Portugal 18: France 19: Greece 20: Poland 21: Hungary 22: Czech 23: Turkey 24: South Africa 25: Taiwan 0: Valid (Remote-controlled server) 1: Valid (L2) 2: Invalid Maximum 256 Bytes Maximum 256 Bytes
Procedure 1
696 697
SYS
2 1
Entering the key code for scrambler board Erasing all data in HDD Destination setting for FAX
SYS
5 3 1
702
Maintenance Maintenance
ALL
2 <0-2> -
SYS
703 707
710
Remote-controlled service HTTP server URL setting Mainte- Remote-controlled service nance HTTP initially-registered server URL setting Mainte- Short time interval setting nance of recovery from Emer(Remote) gency Mode
ALL ALL
SYS SYS
11 11
ALL
24 <1-48>
SYS
Sets the time interval to recover from the Emergency Mode to the Normal Mode. (Unit: Hour)
2 - 90
Classification
Maintenance (Remote) Mainte- Remote-controlled service nance periodical polling timing (Hour/Hour/Minute/Minute) Mainte- Remote-controlled service nance Writing data of self-diagnostic code Mainte- Remote-controlled service nance response waiting time (Timeout) Mainte- Remote-controlled service nance initial registration Maintenance Maintenance Maintenance
Setting mode (08) Default Func- <AcceptItems tion able value> Short time interval setting ALL 60 of Emergency Mode <30-360> ALL ALL ALL ALL 0 <0-1> 3 <1-30> 0 <0-2> 0 <0-1> 2 <0-2>
Contents Unit: Minute 0 (0:00) to 2359 (23:59) 0: Prohibited 1: Accepted Unit: Minute 0: OFF 1: Start 2: Only certification is scanned Maximum 10 letters 0: Not registered 1: Registered 0: OFF 1: Notifies all service calls 2: Notifies all but paper jams Maximum 256 letters 0: Valid 1: Invalid 000.000.000.000255.255.255.255 (Default value 000.000.000.000)
Procedure 1 1 1 1 1
719 720
721
Remote-controlled service tentative password Status of remote-controlled service initial registration (Display only) Service center call function
ALL ALL
SYS SYS
11 2
ALL
SYS
Maintenance Maintenance Maintenance Maintenance Maintenance Maintenance Maintenance Maintenance (Remote) Maintenance (Remote) Maintenance (Remote)
Service center call HTTP server URL setting HTTP proxy setting HTTP proxy IP address setting HTTP proxy port number setting HTTP proxy ID setting HTTP proxy password setting HTTP proxy panel display Automatic ordering function of supplies Automatic ordering function of supplies FAX number Automatic ordering function of supplies E-mail address
1 <0-1> -
11 1 11
SYS SYS SYS SYS SYS Maximum 30 letters Maximum 30 letters 0: Valid 1: Invalid 0: Ordered by FAX 1: Ordered by E-mail 2: Ordered by HTTP 3: OFF Maximum 32 digits Enter hyphen with the [Monitor/Pause] button Maximum 192 letters List: 256 digits
1 11 11 1 1
733 734
ALL ALL
SYS SYS
11 11
2 - 91
Classification Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote)
745
Setting mode (08) Default Func- <AcceptItems tion able value> Automatic ordering funcALL tion of supplies User's name ALL Automatic ordering function of supplies User's telephone number Automatic ordering funcALL tion of supplies User's E-mail address Automatic ordering funcALL tion of supplies User's address ALL 0 Automatic ordering func<5 digits> tion of supplies Service number Automatic ordering funcALL tion of supplies Service technician's name ALL Automatic ordering function of supplies Service technician's telephone number ALL Automatic ordering function of supplies Service technician's E-mail address ALL Automatic ordering function of supplies Supplier's name Automatic ordering funcALL tion of supplies Supplier's address Automatic ordering funcALL tion of supplies Notes ALL Information about supplies Part number of toner cartridge Information about supplies ALL 1 Order quantity of toner car<1-99> tridge Information about supplies ALL 1 Condition number of toner <1-99> cartridge ALL 1 Automatic ordering sup<0-2> plies Result table printout Automatic ordering supALL 2 plies <0-2> Display ALL 0 <0-1>
Contents Maximum 50 letters Maximum 32 digits Enter hyphen with the [Monitor/Pause] button Maximum 192 letters List: 256 digits Maximum 100 letters Maximum 5 digits Maximum 50 letters Maximum 32 digits Enter hyphen with the [Monitor/Pause] button Maximum 192 letters List: 256 digits Maximum 50 letters Maximum 100 letters Maximum 128 letters Maximum 20 digits
Procedure 11 11 11 11 11 11 11
SYS
11
11 11 11 11 1 1
767
SYS
0: OFF 1: Always 2: ON Error 0: Valid (FAX/Internet FAX) 1: Valid (FAX/Internet FAX/HTTP) 2: Invalid Enables to set up to 3 E-mail addresses to be sent.(08-768, 777, 778) 0: Invalid 1: Valid
1 1
2 - 92
Code 768 769 770 771 772 773 774 775 776 777 778 779 780 781 782 783 784 785
Classification Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance Maintenance Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance Maintenance Maintenance Maintenance Maintenance Maintenance
Setting mode (08) Default Func- <AcceptItems tion able value> Destination E-mail address ALL Total counter information transmission setting Total counter transmission interval setting PM counter notification setting Dealer's name Login name Display setting of [Service Notification] button Sending error contents of equipment Setting total counter transmission interval (Hour/Hour/Minute/Minute) Destination E-mail address 2 Destination E-mail address 3 Notification format selection Remote-controlled service polling day selection Day-1 Remote-controlled service polling day selection Day-2 Remote-controlled service polling day selection Day-3 Remote-controlled service polling day selection Day-4 Remote-controlled service polling day selection Sunday Remote-controlled service polling day selection Monday ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL 0 <0-1> 1 <1-31> 0 <0-1> 0 <0-1> 0 <0-1> 0 <0-1> 0 <0-31> 0 <0-31> 0 <0-31> 0 <0-31> 0 <0-1> 0 <0-1>
RAM SYS SYS SYS SYS SYS SYS SYS SYS SYS SYS SYS SYS SYS SYS SYS SYS SYS SYS
Contents Maximum 192 letters 0: Invalid 1: Valid 1 to 31 days 0: Invalid 1: Valid Maximum 100 letters Needed at initial registration Maximum 20 letters Needed at initial registration 0: Not displayed 1: displayed 0: Invalid 1: Valid
Procedure 11 1 1 1 11 11 1 1 1
Maximum 192 letters Maximum 192 letters 0: Text 1: Text + XML data 0: OFF 1 to 31: 1st to 31st of a month 0: OFF 1 to 31: 1st to 31st of a month 0: OFF 1 to 31: 1st to 31st of a month 0: OFF 1 to 31: 1st to 31st of a month 0: Invalid 1: Valid 0: Invalid 1: Valid
11 11 1 1 1 1 1 1 1
2 - 93
Code 786 787 788 789 790 794 796 797 798
Classification Maintenance Maintenance Maintenance Maintenance Maintenance Maintenance Maintenance Maintenance General
Setting mode (08) Default Func- <AcceptItems tion able value> Remote-controlled service ALL 0 <0-1> polling day selection Tuesday ALL 0 Remote-controlled service <0-1> polling day selection Wednesday Remote-controlled service ALL 0 polling day selection <0-1> Thursday Remote-controlled service ALL 0 polling day selection <0-1> Friday ALL 0 Remote-controlled service <0-1> polling day selection Saturday Information of supplies set- ALL 0 ting of toner cartridge <0-1> ALL 0 Remote-controlled service <0-1> lengthened interval polling (End of month) Firmware download ALL 0 <0-1> Notifying address of trial PRT/ 3 period end SCN <0-3>
RAM SYS SYS SYS SYS SYS SYS SYS SYS SYS
Contents 0: Invalid 1: Valid 0: Invalid 1: Valid 0: Invalid 1: Valid 0: Invalid 1: Valid 0: Invalid 1: Valid 0: Invalid 1: Valid 0: Invalid 1: Valid 0: Accepted 1: Prohibited Sets where the end of the trial period is to be notified. 0: OFF 1: User 2: Service center 3: User and service center [CANCEL]: Cancel [EXECUTION]: Forcible end When the Forcible end of trial period is performed, 0 is set in the code (08-673) to end up the trial period forcibly. 0: 130C 1: 135C 2: 140C 3: 145C 4: 150C 5: 155C 6: 160C 7: 165C 8: 170C 9: 175C 10: 180C 11: 185C 12: 120C 0: 130C 1: 135C 2: 140C 3: 145C 4: 150C 5: 155C 6: 160C 7: 165C 8: 170C 9: 175C 10: 180C 11: 185C 12: 120C
Procedure 1 1 1 1 1 1 1 1 1
799
General
PRT/ SCN
SYS
800-0
Fuser
ALL
800-1
ALL
801-0
Fuser
801-1
ALL
ALL
2 - 94 04/09
Code 802-0
Classification Fuser
802-1
Setting mode (08) Default Func- <AcceptItems tion able value> Center ALL 8 Temperature themistor <0-12> control lower limit (Thick paper 2) Side ALL 9 themistor <0-12> Temperature control lower limit (Thick paper 3) Center themistor Side themistor Center themistor Side themistor ALL 8 <0-12> 10 <0-12> 8 <0-12> 10 <0-12> 98 <0-255> 98 <0-255> 98 <0-255> 98 <0-255> 98 <0-255> 128 <0-255> 128 <0-255> 128 <0-255>
RAM M
Contents 0: 130C 1: 135C 2: 140C 3: 145C 4: 150C 5: 155C 6: 160C 7: 165C 8: 170C 9: 175C 10: 180C 11: 185C 12: 120C 0: 130C 1: 135C 2: 140C 3: 145C 4: 150C 5: 155C 6: 160C 7: 165C 8: 170C 9: 175C 10: 180C 11: 185C 12: 120C 0: 130C 1: 135C 2: 140C 3: 145C 4: 150C 5: 155C 6: 160C 7: 165C 8: 170C 9: 175C 10: 180C 11: 185C 12: 120C Corrects the value of the main charger bias adjustment (05-210).
Procedure 4
803-0
Fuser
803-1
ALL
804-0
Fuser
ALL
804-1
ALL
805 806
Charger Charger
Main charger bias correction (Text/Photo/OHP film) Main charger bias correction (Toner Saving Mode/OHP film) Main charger bias correction (Text/Photo/OHP film) Main charger bias correction (Text/OHP film) Main charger bias correction (Photo/OHP film) Main charger bias correction (Toner saving mode) Transfer transformer DC correction (C) Separation transformer DC correction (C)
PRT PRT
M M
1 1
M M M M M Corrects the value of the transfer transformer DC output adjustment (05-221). Corrects the value of the separation transformer DC output adjustment (05-234).
1 1 1 1 1
831
Separation
ALL
2 - 95 04/09
Classification Developer Developer Developer Developer Developer Image processing Image processing
Setting mode (08) Default Func- <AcceptItems tion able value> Developer bias DC correcPRT 108 <0-255> tion (Text/Photo/OHP film) Developer bias DC correcPRT 108 tion <0-255> (Toner Saving Mode/OHP film) PPC 108 Developer bias DC correc<0-255> tion (Text/Photo/OHP film) Developer bias DC correcPPC 108 tion <0-255> (Text/OHP film) Developer bias DC correcPPC 108 tion <0-255> (Photo/OHP film) Switching of recycled toner ALL 0 saving control <0-1> Correction by temperature/ humidity ALL 0 <0-3>
RAM M M
Procedure 1 1
M M M M M 0: Switched 1: Not switched Sets the correction by temperature/humidity. 0: All valid 1: All invalid 2: Valid only in autotoner sensor 3: All valid except transfer and separation 0: Other than SAD 1: SAD Corrects the value of the developer bias adjustment (05-205). Corrects the value of the developer bias adjustment (05-205). Corrects the value of the developer bias adjustment (05-205). Corrects the value of the developer bias adjustment (05-205). Corrects the value of the developer bias adjustment (05-205). Corrects the value of the main charger bias adjustment (05-210). Corrects the value of the main charger bias adjustment (05-210).
1 1 1 1 1
Power source setting for destination Developer bias DC correction (Toner saving mode) Developer bias DC correction (Normal) Developer bias DC correction (Text/Photo) Developer bias DC correction (Text) Developer bias DC correction (Photo) Main charger bias correction (Normal) Main charger bias correction (Text/Photo)
SAD: 1 Others: 0 <0-1> 128 <0-255> 128 <0-255> 128 <0-255> 128 <0-255> 128 <0-255> 128 <0-255> 128 <0-255>
M M M M M M M
1 1 1 1 1 1 1
865
Charger
PPC
2 - 96
Code 866
Classification Charger
Setting mode (08) Default Func- <AcceptItems tion able value> Main charger bias correcPPC 128 tion (Text) <0-255> Main charger bias correction (Photo) Transfer transformer DC correction (H) Transfer transformer DC correction (L) Separation transformer DC correction (H) Separation transformer DC correction (L) Laser power correction (Normal) Laser power correction (Text/Photo) Laser power correction (Toner saving mode) Laser power correction (Text) Laser power correction (Photo) PPC 128 <0-255> 128 <0-255> 128 <0-255> 128 <0-255> 128 <0-255> 128 <0-255> 128 <0-255> 128 <0-255> 128 <0-255> 128 <0-255>
RAM M
Contents Corrects the value of the main charger bias adjustment (05-210). Corrects the value of the main charger bias adjustment (05-210). Corrects the value of the transfer transformer DC output adjustment (05-220). Corrects the value of the transfer transformer DC output adjustment (05-222). Corrects the value of the separation transformer DC output adjustment (05-233). Corrects the value of the separation transformer DC output adjustment (05-235). Corrects the value of the laser power adjustment (05-286). Corrects the value of the laser power adjustment (05-286). Corrects the value of the laser power adjustment (05-286). Corrects the value of the laser power adjustment (05-286). Corrects the value of the laser power adjustment (05-286).
Procedure 1
867
Charger
868
Transfer
ALL
869
Transfer
ALL
870
ALL
871
ALL
M M M M M
1 1 1 1 1
2 - 97
Code 886
Classification Fuser
Setting mode (08) Default Func- <AcceptItems tion able value> Temperature drop control ALL 2 <0-20> setting in ready status (Temperature/Time)
RAM M
Contents 0: None 1: Pattern 1 2: Pattern 2 3: Pattern 3 4: Pattern 4 5: Pattern 5 6: Pattern 6 7: Pattern 7 8: Pattern 8 9: Pattern 9 10: Pattern 10 11: Pattern 11 12: Pattern 12 13: Pattern 13 14: Pattern 14 15: Pattern 15 16: Pattern 16 17: Pattern 17 18: Pattern 18 19: Pattern 19 20: Manual adjustment 0: 130C 1: 135C 2: 140C 3: 145C 4: 150C 5: 155C 6: 160C 7: 165C 8: 170C 9: 175C 10: 180C 11: 185C 12: 120C JPN: T371SY0JXXX UC: T371SY0UXXX EUR: T371SY0EXXX Others: T371SY0XXXX 371M-XXX 371S-XXX DF-XXXX SDL-XX FIN-XX F562-XXX X.XXX VX.XX/X.XX VXXX.XXX X VXXX.XXX X VXXX.XXX X VXXX.XXX X VXXX.XXX X VXXX.XXX X VXXX.XXX X VXXX.XXX X
Procedure 1
896-0
Fuser
896-1
ALL
7 <0-12> 5 <0-12> -
ALL
900
Version
System firmware ROM version Engine ROM version Scanner ROM version RADF ROM version Finisher ROM version Fax board ROM version NIC board ROM version FROM basic section software version FROM internal program UI data fixed section version UI data common section version Version of UI data language 1 in HDD Version of UI data language 2 in HDD Version of UI data language 3 in HDD Version of UI data language 4 in HDD Version of UI data language 5 in HDD
ALL
903 905 907 908 915 916 920 921 922 923 924 925 926 927 928
Version Version Version Version Version Version Version Version Version Version Version Version Version Version Version
ALL ALL ALL ALL FAX ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL
2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
2 - 98 04/09
Code 929 930 931 933 934 935 936 937 938 939 944
Classification Version Version Version Version Version Version Version Version Version Version Version
Items
Version of UI data language 6 in HDD Version of UI data in FROM displayed at powerON Version of UI data language 7 in HDD Web data whole version Web UI data in HDD Version: Language 1 Web UI data in HDD Version: Language 2 Web UI data in HDD Version: Language 3 Web UI data in HDD Version: Language 4 Web UI data in HDD Version: Language 5 Web UI data in HDD Version: Language 6 HD version
Setting mode (08) Default Func- <Accepttion able value> ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL -
RAM -
Contents VXXX.XXX X VXXX.XXX X VXXX.XXX X VXXX.XXX X VXXX.XXX X VXXX.XXX X VXXX.XXX X VXXX.XXX X VXXX.XXX X VXXX.XXX X JPN: T371HD0JXXX UC: T371HD0UXXX EUR: T371HD0EXXX Others: T371HD0XXXX 1: Valid 2: Invalid Perform this code when the software in this equipment has been upgraded. Sets the mode to enter when the [Energy Saver] button is pressed for a while. 0: Sleep Mode 1: Auto Shut Off Mode Sets the number of pages to interrupt the printing automatically. 0-100: 0 to 100 pages Sets the start-up method of the Electronic Filing. 0: Standard 1: Forced start-up (Not recovered) 2: Forced start-up (Recovered) 0: Renewed automatically 1: Enter every time 0: Immediately after the completion of scanning 1: Cleared by Auto Clear
Procedure 2 2 2 2 2 2 2 2 2 2 2
945 947
Network General
Two-way setting of RawPort 9100 Initialization after software version upgrade Mode setting by pressing [Energy Saver] button for a while
ALL ALL
1 <1-2> -
UTY -
12 3
948
General
ALL
0 <0-1>
SYS
949
General
ALL
0 <0-100> 0 <0-2>
SYS
950
ALL
SYS
953 954
Access code entry for Electronic Filing printing Clearing timing for files and Electronic Filing Agent
ALL ALL
0 <0-1> 1 <0-1>
SYS SYS
1 1
2 - 99
04/09
Setting mode (08) Default Func- <AcceptItems tion able value> Error sound ALL 1 <0-1> Sound setting when ALL 1 switching to Energy Saving <0-1> Mode PCL line feed code setting PRT 0 <0-3>
Contents
Procedure 1 1 1
975
General
ALL
1 <0-1>
SYS
976
ElecEquipment name setting to tronic Fil- a folder when saving files ing
ALL
0 <0-1>
SYS
977 978
Network Network
Switching of extended ASCII code in catFs filesystem Raw printing job (Paper feeding drawer)
ALL PRT
0 <0-1> 0 <0-5>
SYS SYS
Sets the PCL line feed code. 0: Automatic setting 1: CR=CR, LF=LF 2: CR=CR+LF, LF=LF 3: CR=CR, LF=CR+LF Sets whether pause or stop the printing job when it is short paid using a coin controller. 0: Pause the job 1: Stop the job Sets whether or not adding the equipment name to the folder when saving files. 0: Not add 1: Add 0: ISO8859-1 1: ISO8859-2 0: AUTO 1: Upper drawer 2: Lower drawer 3: PFP upper drawer 4: PFP lower drawer 5: LCF
1 1
2 - 100
04/09
Code 979
Classification Network
Setting mode (08) Default Func- <Accepttion able value> PRT 0 <0-39>
RAM SYS 0: 1: 2: 3: 4:
Contents Roman-8 ISO 8859/1 Latin 1 ISO 8859/2 Latin 2 ISO 8859/9 Latin 5 PC-8,Code Page 437 5: PC-8 D/N, Danish/ Norwegian 6: PC-850,Multilingual 7: PC-852, Latin2 8: PC-8 Turkish 9: Windows 3.1 Latin 1 10: Windows 3.1 Latin 2 11: Windows 3.1 Latin 5 12: DeskTop 13: PS Text 14: Ventura International 15: Ventura US 16: Microsoft Publishing 17: Math-8 18: PS Math 19: Ventura Math 20: Pi Font 21: Legal 22: ISO 4: United Kingdom 23: ISO 6: ASCII 24: ISO 11 25: ISO 15: Italian 26: ISO 17 27: ISO 21: German 28: ISO 60: Danish/Norwegian 29: ISO 69: French 30: Windows 3.0 Latin 1 31: MC Text 32: PC Cyrillic 33: ITC Zapf Dingbats 34: ISO 8859/10 Latin 6 35: PC-775 36: PC-1004 37: Symbol 38: Windows Baltic 39: Wingdings 0: Retention OFF 1 to 999: 1 to 999 days 0: Retention OFF 1 to 999: 1 to 999 days 0: Image quality priority mode 1: Function priority mode
Procedure 1
980
981
985
ElecElectronic Filing data tronic Fil- retention period when NIC ing board is not installed (Public Box) ElecElectronic Filing data tronic Fil- retention period when NIC ing board is not installed (User Box) ElecPrint mode setting of mixed tronic Fil- input source of Electronic ing Filing
ALL
SYS
ALL
SYS
ALL
SYS
2 - 101
04/09
Code 986
Classification General
Setting mode (08) Default Func- <Accepttion able value> PPC 0 <0-1> ALL ALL 0 <0-2> 0 <10 digits> 0 <8 digits> 3 <1-3> 1 <1-2>
RAM SYS
Contents Sets the copy function to be invalid. 0: Valid 1: Invalid 0: Not switched 1: LG 13LG 2: FOLIO 13LG This code can be also keyed in from the adjustment mode (05976). 10 digits Refers to values of total counter 1: Cold 2: Warm 3: Not reset 1: Not printed out when the equipment is restarted 2: Printed out when the equipment is restarted 1: 10 MBPS 2: 100 MBPS 3: Automatic Writing only (Current setting is not displayed.) Maximum 31 letters 1: Available 2: Not available 1: Unchanging 2: Automatic addressing (DHCP) 3: No IP address applied to automatic addressing (DHCP) Maximum 96 letters 000.000.000.000255.255.255.255 (Default value 000.000.000.000) 000.000.000.000255.255.255.255 (Default value 000.000.000.000) 000.000.000.000255.255.255.255 (Default value 000.000.000.000) 1: Available 2: Not available
Procedure 1
988 995
SYS SYS
1 11
FSMS total counter Reset of NIC board Selection of NIC board status information
1 12 12
1003 1004
Network Network
ALL ALL
3 <1-3> -
NIC NIC
12 12
1005 1006
Network Network
ALL ALL
1 <1-2> 2 <1-3>
NIC NIC
12 12
1007 1008
Network Network
ALL ALL
NIC NIC
12 12
1009
Network
Subnet mask
ALL
NIC
12
1010
Network
Gateway
ALL
NIC
12
1011
Network
Availability of IPX
ALL
1 <1-2>
NIC
12
2 - 102
Code 1012
Classification Network
Setting mode (08) Default Func- <Accepttion able value> ALL 1 <1-5>
RAM NIC
Contents 1: Automatic 2: IEEE802.3 3: Ethernet II 4: IEEE802.3SNAP 5: IEEE802.2 1: Available 2: Not available 1: Available 2: Not available Maximum 32 letters *: Wildcard character 1: Available 2: Not available 1: Available 2: Not available 000.000.000.000255.255.255.255 (Default value 000.000.000.000) 000.000.000.000255.255.255.255 (Default value 000.000.000.000) 1: Invalid 2: Via DHCP 3: Insecure DDNS 4: Secure DDNS 5: Multi-secure DDNS 1: Available 2: Not available Maximum 15 letters Maximum 128 letters Maximum 128 letters 1: Available 2: Not available 1: Available 2: Not available Maximum 127 letters Maximum 47 letters 1: Available 2: Not available
Procedure 12
2
12 12 12 12 12 12
Availability of NCP Burst Availability of AppleTalk Zone setting of AppleTalk Availability of LDAP Availability of DNS IP address to DNS server (Primary) IP address to DNS server (Secondary) DDNS Desired level
1019
Network
ALL
NIC
12
1020
Network
ALL
1 <1-5>
NIC
12
1021 1023 1024 1025 1026 1027 1028 1029 1030 1031 1032 1033 1034
Network Network Network Network Network Network Network Network Network Network Network Network Network
Availability of SLP NetBios name Name of WINS server or IP address (Primary) Name of WINS server or IP address (Secondary) Availability of Bindery Availability of NDS Directory service context Directory service tree Availability of HTTP server Port number to NIC HTTP server Port number to system HTTP server Availability of NIC HTTP client TCP port number to Controller HTTP client
ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL
NIC NIC NIC NIC NIC NIC NIC NIC NIC NIC SYS NIC NIC
12 12 12 12 12 12 12 12 12 12 1
12 12
2 - 103
Code 1035
Classification Network
Setting mode (08) Default Func- <AcceptItems tion able value> IP address to HTTP server ALL (Primary) Availability of SMTP client FQDN or IP address to SMTP server TCP port number of SMTP client Availability of SMTP server TCP port number of SMTP server E-mail box name to SMTP server Availability of Offramp Offramp security Printing at Offramp Availability of POP3 clients FQDN or IP address to POP3 server Types of POP3 server Login name to POP3 server Login password to POP3 E-mail reception interval (Unit: Minute) TCP port number of POP3 client Availability of FTP client FQDN or IP address to FTP server TCP port number of FTP client Data port number of FTP client Login name to FTP server Login password to FTP server Availability of FTP server ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL 1 <1-2> 25 <165535> 1 <1-2> 25 <165535> 2 <1-2> 1 <1-2> 1 <1-2> 1 <1-2> 1 <1-3> 5 <0-4096> 110 <165535> 1 <1-2> 21 <165535> 0 <065535> 1 <1-2>
RAM NIC
Contents 000.000.000.000255.255.255.255 (Default value 000.000.000.000) 1: Available 2: Not available Maximum 128 Bytes
Procedure 12
1037 1038 1039 1040 1041 1042 1043 1044 1045 1046 1047 1048 1049 1050 1051 1052 1053 1054 1055 1056 1057 1058 1059
Network Network Network Network Network Network Network Network Network Network Network Network Network Network Network Network Network Network Network Network Network Network Network
NIC NIC NIC NIC NIC NIC NIC NIC NIC NIC NIC NIC NIC NIC NIC NIC NIC NIC NIC NIC SYS SYS NIC
12 12 12
12 12
Maximum 192 letters 1: Available 2: Not available 1: Available 2: Not available 1: Available 2: Not available 1: Available 2: Not available Maximum 128 Bytes 1: Automatic 2: POP3 3: APOP Maximum 96 letters Maximum 96 letters
12 12 12 12 12 12 12 12 12 12 12
12 12 12 12
11 11 12
2 - 104
Code 1060 1061 1062 1063 1065 1066 1067 1068 1069
Classification Network Network Network Network Network Network Network Network Network
Setting mode (08) Default Func- <AcceptItems tion able value> TCP port number of FTP ALL 21 server <165535> Login name to FTP client ALL Login password to FTP cliALL ent MIB function ALL 1 <1-2> Setting of read Community ALL public Setting of read/Write ComALL private munity Authentication TRAP funcALL 1 tion <1-2> ALERTS TRAP function ALL 1 <1-2> TRAP destination IP ALL address Community setting of TRAP (via IP) Availability of Raw/TCP TCP port number of Raw Availability of LPD client TCP port number of LPD LPD queue name Availability of IPP Availability of IPP port number 80 TCP port number of IPP IPP printer name IPP printer location IPP printer information IPP printer information (more) Installer of IPP printer driver IPP printer Make and Model IPP printer information (more) MFGR IPP message from operator Availability of FTP print Printer user name of FTP ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL public 1 <1-2> 9100 <165535> 1 <1-2> 515 <165535> 1 <1-2> 1 <1-2> 631 <165535> 1 <1-2> print
RAM NIC SYS SYS NIC NIC NIC NIC NIC NIC
Contents
Procedure 12
Maximum 31 letters Maximum 31 letters 1: Valid 2: Invalid Maximum 31 letters Maximum 31 letters 1: Valid 2: Invalid 1: Valid 2: Invalid 000.000.000.000255.255.255.255 (Default value 000.000.000.000) Maximum 31 letters 1: Valid 2: Invalid
11 11 12 12 12 12 12 12
1070 1073 1074 1075 1076 1077 1078 1079 1080 1081 1082 1083 1084 1085 1086 1087 1088 1089 1090
Network Network Network Network Network Network Network Network Network Network Network Network Network Network Network Network Network Network Network
NIC NIC NIC NIC NIC NIC NIC NIC NIC NIC NIC NIC NIC NIC NIC NIC NIC NIC NIC
12 12 12
1: Valid 2: Invalid
12 12
12 12 12 12
Maximum 127 letters Maximum 127 letters Maximum 127 letters Maximum 127 letters Maximum 127 letters Maximum 127 letters Maximum 127 letters Maximum 127 letters 1: Available 2: Not available Maximum 31 letters
12 12 12 12 12 12 12 12 12 12
2 - 105
Code 1091 1092 1093 1094 1095 1096 1097 1098 1099 1100
Classification Network Network Network Network Network Network Network Network Network Network
Setting mode (08) Default Func- <AcceptItems tion able value> Printer user password of ALL FTP TCP port number to FTP ALL 21 print server <165535> Login name to Novell print ALL server Login password to Novell ALL print server Name of SearchRoot ALL server Scan rate setting of print ALL 5 queue <1-255> Page number limitation for ALL 5 printing text of received E<1-99> mail MDN return mail setting ALL 2 when receiving E-mail <1-2> Trap destination of IPX ALL Method of SMTP server authentication ALL 5 <1-5>
RAM NIC NIC NIC NIC NIC NIC UTY UTY UTY NIC
Procedure 12 12
12 12 12 12 12
Login name for SMTP server authentication Login password for SMTP server authentication Rendezvous setting Link local host name Service name setting
1: Valid 2: Invalid Maximum 24 letters (Valid from 0 to 9 and from A to F) 1: Plain 2: Login 3: Cram-MD5 4: Digest MD5 5: Disable Maximum 64 letters Maximum 64 letters 1: Valid 2: Invalid Maximum 127 letters Maximum 63 letters <Default value> e-STUDIO230: TOSHIBA eSTUDIO230 e-STUDIO280: TOSHIBA eSTUDIO280 1: Valid 2: Invalid Maximum 127 letters Maximum 96 letters 0: Invalid (Not sending the mail text) 1: Valid (Sending the mail text) Unit: Second
12 12 12
12 12 12 12 12
FTP server setting Host name NT domain name Sending mail text of InternetFAX SMB time-out period
12 12 12 1
1117
Network
ALL
SYS
2 - 106
04/09
Code 1120
Classification Network
Setting mode (08) Default Func- <AcceptItems tion able value> Backup/Restore of NIC ALL 0 setting information <0-1>
RAM SYS
Contents 0: Read (Reads all of the setting information in NIC and create a file NAM1B (no extension) in USB) 1: Write (Writes all of the setting information read from a file NAM1B (no extension) in USB) Maximum 15 letters Maximum 15 letters 3: ON (Domain selected) 4: OFF (Work group selected) Maximum 15 letters Sets the Job Build Function. 0: Invalid 1: Valid Sets the maximum number of time a job build has been performed. 5-1000: 5 to 1000 times Selects the default screen when entering the User Function menu by pressing the [USER FUNCTIONS] button. 0: ADDRESS 1: COUNTER Sets the feeding direction of envelopes. 0: Envelope flap comes on its trailing edge (front side of the equipment) 1: Envelope flap comes on its leading edge (rear side of the equipment) 1: LCF 2: Upper drawer 3: Lower drawer 4: PFP upper drawer 5: PFP lower drawer
Procedure 1
PDC (Primary Domain Controller) name BDC (Backup Domain Controller) name NT domain ON/OFF setting Workgroup name Job Build Function
12 12 12
1124 1130
ALL ALL
UTY SYS
12 1
1131
ALL
SYS
1132
General
ALL
1 <0-1>
SYS
1133
Paper feeding
ALL
0 <0-1>
SYS
1135
Paper feeding
PRT
1 <1-5>
SYS
1136 1137
Network Network
Number of lines simultaneously connectable when using SMB Memory partition size when using Samba
ALL ALL
8 <0-16> 12 <8-20>
1 1
2 - 107
04/09
Code 1138
Classification Network
Setting mode (08) Default Func- <AcceptItems tion able value> LDAP search method setALL 0 ting <0-3>
RAM SYS
Contents Sets the search method when performing a LDAP search. 0: Partial match 1: Prefix match 2: Suffix match 3: Full match 0: Not authenticated 1: Authenticated Selects the restriction of the template function usage setting. 0: No restriction 1: Only available with the administrator privilege. Counts up the heater control time accumulated (when power of the equipment is ON) but does not count at the Sleep Mode. When the counter value of the fuser roller is cleared, this counter value is also cleared in sync at the PM support mode. Counts the rotation number of the toner cartridge. Counts up the heater control time accumulated (when the equipment is at ready status). When the counter value of the fuser roller is reset, this counter is also reset in sync at the PM support mode. Counts up the heater control time accumulated (during printing). When the counter value of the fuser roller is reset, this counter is also reset in sync at the PM support mode. Counts up the heater control time accumulated (when the equipment is in the Energy Saving Mode). When the counter value of the fuser roller is reset, this counter is also reset in sync at the PM support mode.
Procedure 1
1139 1140
LDAP authentication setting Restriction of the template function with the administrator privilege
ALL ALL
0 <0-1> 0 <0-1>
SYS SYS
1 1
1372
Counter
ALL
0 <8 digits>
1376 1378
Counter Counter
Toner cartridge drive counter Counter for period of time fuser unit is at ready temperature
ALL ALL
M M
1 1
1380
Counter
ALL
0 <8 digits>
1382
Counter
Counter for period of time fuser unit is at energy saving temperature/Counter reset
ALL
0 <8 digits>
2 - 108
04/09
Code 1385
Setting mode (08) Default Func- <AcceptItems tion able value> Number of output pages ALL 0 (Thick paper 1) <8 digits>
RAM M
Contents Counts up when the registration sensor is ON. When the counter value of the fuser roller is cleared, this counter value is also cleared in sync at the PM support mode. Counts up when the registration sensor is ON. When the counter value of the fuser roller is cleared, this counter value is also cleared in sync at PM support mode. Counts up when the registration sensor is ON. When the counter value of the fuser roller is cleared, this counter value is also cleared in sync at PM support mode. Counts up when the registration sensor is ON. When the counter value of the fuser roller is cleared, this counter value is also cleared in sync at PM support mode. Counts the number of times of the feeding retry from the upper drawer. Counts the number of times of the feeding retry from the lower drawer. Counts the number of times of the feeding retry from the PFP upper drawer. Counts the number of times of the feeding retry from the PFP lower drawer. Counts the number of times of the feeding retry from the bypass tray. Counts the number of times of the feeding retry from the LCF.
Procedure 1
1386
Image processing
ALL
0 <8 digits>
1387
Image processing
ALL
0 <8 digits>
1388
Image processing
ALL
0 <8 digits>
1390
Paper feeding Paper feeding Paper feeding Paper feeding Paper feeding Paper feeding
Feeding retry counter (upper drawer) Feeding retry counter (lower drawer) Feeding retry counter (PFP upper drawer) Feeding retry counter (PFP lower drawer) Feeding retry counter (bypass feed) Feeding retry counter (LCF)
ALL
0 <8 digits> 0 <8 digits> 0 <8 digits> 0 <8 digits> 0 <8 digits> 0 <8 digits>
1391
ALL
1392
ALL
1393
ALL
1394
ALL
1395
ALL
2 - 109
Classification Paper feeding Paper feeding Paper feeding Paper feeding Paper feeding Paper feeding Counter Counter
Items
Feeding retry counter upper limit value (Upper drawer) Feeding retry counter upper limit value (Lower drawer) Feeding retry counter upper limit value (PFP upper drawer) Feeding retry counter upper limit value (PFP lower drawer) Feeding retry counter upper limit value (Bypass feed) Feeding retry counter upper limit value (LCF) Counter for period of toner cartridge rotation time Counter for envelope
Setting mode (08) Default Func- <Accepttion able value> ALL 0 <8 digits> ALL ALL ALL ALL ALL ALL ALL 0 <8 digits> 0 <8 digits> 0 <8 digits> 0 <8 digits> 0 <8 digits> 0 <8 digits> 0 <8 digits>
RAM M M M M M M M M
Contents When the number of feeding retry (08-1390 to 08-1395) exceeds the setting value, the feeding retry will not be performed subsequently. In case 0 is set as a setting value, however, the feeding retry continues regardless of the counter setting value.
Procedure 1 1 1 1 1 1
Counts up the period of rotation time of the toner cartridge. Counts up when the registration sensor is ON. When the counter value of the fuser roller is reset, this counter is reset in sync at the PM support mode.
1 1
2 - 110
Code 1500
RAM SYS
Contents Selects the standard paper size to convert it into the pixel count (%). 0: A4 1: LT Clears all information related to the pixel counter. Clears all information related to the service technician reference pixel counter. Clears all information related to the toner cartridge reference pixel counter. Selects whether or not to display the pixel counter on the LCD screen. 0: Displayed 1: Not displayed Selects the reference when displaying the pixel counter on the LCD screen. 0: Service technician reference 1: Toner cartridge reference Selects the counter to determine toner empty. 0: Output pages 1: Pixel counter Sets the number of output pages to determine toner empty. This setting is valid when 0 is set at 08-1506. Becomes 1 when 081502 is performed. Displays the date on which 08-1502 was performed. Displays the date on which 08-1503 was performed. Displays the date on which 08-1503 was performed. Counts the number of output pages converted to the standard paper size in the copy function and service technician reference. [Unit. page]
2
3 3
1501 1502
SYS SYS
1503
ALL
SYS
1504
ALL
1 <0-1>
SYS
1505
Pixel counter
ALL
0 <0-1>
SYS
1506
Toner empty determination counter setting Threshold setting for toner empty determination (Output pages) Pixel counter clear flag/ Service technician reference Service technician reference cleared date Toner cartridge reference cleared date Toner cartridge reference count started date Number of output pages (Service technician reference)
ALL
SYS
1507
ALL
SYS
Pixel counter Pixel counter Pixel counter Pixel counter Pixel counter
2 2 2 2 2
2 - 111
Code 1550
Setting mode (08) Default Func- <AcceptItems tion able value> Number of output pages PRT <8 digits> (Service technician reference)
RAM SYS
Contents Counts the number of output pages converted to the standard paper size in the printer function and service technician reference. [Unit. page] Counts the number of output pages converted to the standard paper size in the FAX function and service technician reference. [Unit. page] Counts the number of output pages converted to the standard paper size in the copy function and toner cartridge reference. [Unit. page] Counts the number of output pages converted to the standard paper size in the printer function and toner cartridge reference. [Unit. page] Counts the number of output pages converted to the standard paper size in the FAX function and toner cartridge reference. [Unit. page] Counts the number of time of the toner cartridge replacement. Displays the average pixel count in the copy function and service technician reference. [Unit: 0.01%] Displays the average pixel count in the printer function and service technician reference. [Unit: 0.01%] Displays the average pixel count in the FAX function and service technician reference. [Unit: 0.01%]
Procedure 2
1551
Pixel counter
FAX
<8 digits>
SYS
1553
Pixel counter
PPC
<8 digits>
SYS
1555
Pixel counter
PRT
<8 digits>
SYS
1556
Pixel counter
FAX
<8 digits>
SYS
1566 1592
Toner cartridge replacement counter Average pixel count (Service technician reference) Average pixel count (Service technician reference) Average pixel count (Service technician reference)
ALL PPC
SYS SYS
2 2
1593
Pixel counter
PRT
SYS
1594
Pixel counter
FAX
SYS
2 - 112
Code 1595
Setting mode (08) Default Func- <AcceptItems tion able value> Average pixel count PPC/ 0 PRT/ <0(Service technician reference) FAX 10000>
RAM SYS
Contents Displays the average pixel count in the copy/ printer/FAX function and service technician reference. [Unit: 0.01%] Displays the latest pixel count in the copy function and service technician reference. [Unit: 0.01%] Displays the latest pixel count in the printer function and service technician reference. [Unit: 0.01%] Displays the latest pixel count in the FAX function and service technician reference. [Unit: 0.01%] Displays the average pixel count in the copy function and toner cartridge reference. [Unit: 0.01%] Displays the average pixel count in the printer function, and toner cartridge reference. [Unit: 0.01%] Displays the average pixel count in the copy/ printer/FAX function and toner cartridge reference. [Unit: 0.01%] Displays the average pixel count in the FAX function and toner cartridge reference. [Unit: 0.01%] Displays the latest pixel count in the FAX function and toner cartridge reference. [Unit: 0.01%] Displays the latest pixel count in the copy function and toner cartridge reference. [Unit: 0.01%] Displays the latest pixel count in the printer function and toner cartridge reference. [Unit: 0.01%]
Procedure 2
2
2
1606
Pixel counter
Latest pixel count (Service technician reference) Latest pixel count (Service technician reference) Latest pixel count (Service technician reference) Average pixel count (Toner cartridge reference)
PPC
0 <010000> 0 <010000> 0 <010000> 0 <010000> 0 <010000> 0 <010000> 0 <010000> 0 <010000> 0 <010000> 0 <010000>
SYS
1607
Pixel counter
PRT
SYS
1608
Pixel counter
FAX
SYS
1613
Pixel counter
PPC
SYS
1619
Pixel counter
PRT
SYS
1624
Pixel counter
SYS
1625
Pixel counter
SYS
1634
Latest pixel count (Toner cartridge reference) Latest pixel count (Toner cartridge reference) Latest pixel count (Toner cartridge reference)
FAX
SYS
1639
PPC
SYS
1640
PRT
SYS
2 - 113
Code 1649-0 1649-1 1649-2 1649-3 1649-4 1649-5 1649-6 1649-7 1649-8 1649-9 1650-0 1650-1 1650-2 1650-3 1650-4 1650-5 1650-6 1650-7 1650-8 1650-9 1651-0 1651-1 1651-2 1651-3 1651-4 1651-5 1651-6 1651-7 1651-8 1651-9
Pixel counter
Pixel counter
Setting mode (08) Default Func- <AcceptItems tion able value> Pixel count 0-5% PPC <8 digits> distribution 5.1-10% PPC <8 digits> 10.1-15% PPC <8 digits> 15.1-20% PPC <8 digits> 20.1-25% PPC <8 digits> 25.1-30% PPC <8 digits> 30.1-40% PPC <8 digits> 40.1-60% PPC <8 digits> 60.1-80% PPC <8 digits> 80.1PPC <8 digits> 100% Pixel count 0-5% PRT <8 digits> distribution 5.1-10% PRT <8 digits> 10.1-15% PRT <8 digits> 15.1-20% PRT <8 digits> 20.1-25% PRT <8 digits> 25.1-30% PRT <8 digits> 30.1-40% PRT <8 digits> 40.1-60% PRT <8 digits> 60.1-80% PRT <8 digits> 80.1PRT <8 digits> 100% Pixel count 0-5% FAX <8 digits> distribution 5.1-10% FAX <8 digits> 10.1-15% FAX <8 digits> 15.1-20% FAX <8 digits> 20.1-25% FAX <8 digits> 25.1-30% FAX <8 digits> 30.1-40% FAX <8 digits> 40.1-60% FAX <8 digits> 60.1-80% FAX <8 digits> 80.1FAX <8 digits> 100%
RAM SYS SYS SYS SYS SYS SYS SYS SYS SYS SYS SYS SYS SYS SYS SYS SYS SYS SYS SYS SYS SYS SYS SYS SYS SYS SYS SYS SYS SYS SYS
Contents The pixel count data are divided into 10 ranges. The number of output pages in each range is displayed. In this code, the distributions in the copy function are displayed. [Unit: page]
Procedure 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14
The pixel count data are divided into 10 ranges. The number of output pages in each range is displayed. In this code, the distributions in the printer function are displayed. [Unit: page]
The pixel count data are divided into 10 ranges. The number of output pages in each range is displayed. In this code, the distributions in the FAX function are displayed. [Unit: page]
2 - 114
<<PM support mode related code>> The management items at PM support mode can also be operated at setting mode (08). The following items are displayed or set by using sub-codes at PM management setting in the table below. <Sub-codes> 0: Present number of output pages - Means the present number of output pages. 1: Recommended number of output pages for replacement - Means the recommended number of output pages for replacement. 2: Number of output pages at the last replacement - Means the number of output pages at the last replacement. 3: Present driving counts - Means the present drive counts (1 count = 2 seconds). 4: Recommended driving counts to be replaced - Means the recommended drive counts for replacement (1 count = 2 seconds). 5: Driving counts at the last replacement - Means the drive counts at the last replacement. 6: Present output pages for control - Means the present number of output pages for controlling. 7: Present driving counts for control - Means the present drive counts for controlling (1 count = 2 seconds). 8: Number of times replaced - Counts up when clearing the counter of each unit in the PM Support Mode Screen. Notes: Sub-code 3 is equivalent to sub-code 7. When the value of sub-code 3 is changed, the value of sub-code 7 is also updated and vice versa. When 0 is set at one of sub-codes 0, 3, 6 and 7, the rest of them are automatically updated to 0.
2 - 115
Remarks <Default values of code 1150 (e-STUDIO230/280)> Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0 Sub-code 1: 74,000/90,000 Sub-code 4: 120,000/120,000 <Default values of code 1158 (e-STUDIO230/280)> Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0 Sub-code 1: 74,000/90,000 Sub-code 4: 120,000/120,000 <Default values of code 1172 (e-STUDIO230/280)> Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0 Sub-code 1: 74,000/90,000 Sub-code 4: 120,000/120,000 <Default values of code 1174 (e-STUDIO230/280)> Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0 Sub-code 1: 74,000/90,000 Sub-code 4: 120,000/120,000 <Default values of code 1182 (e-STUDIO230/280)> Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0 Sub-code 1: 74,000/90,000 Sub-code 4: 120,000/120,000 <Default values of code 1198 (e-STUDIO230/280)> Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0 Sub-code 1: 148,000/180,000 Sub-code 4: 240,000/240,000 <Default values of code 1200 (e-STUDIO230/280)> Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0 Sub-code 1: 74,000/90,000 Sub-code 4: 120,000/120,000 <Default values of code 1214 (e-STUDIO230/280)> Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0 Sub-code 1: 74,000/90,000 Sub-code 4: 120,000/120,000 <Default values of code 1224 (e-STUDIO230/280)> Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0 Sub-code 1: 74,000/90,000 Sub-code 4: 120,000/120,000 <Default values of code 1246 (e-STUDIO230/280)> Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0 Sub-code 1: 148,000/180,000 Sub-code 4: 240,000/240,000 <Default values of code 1250 (e-STUDIO230/280)> Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0 Sub-code 1: 148,000/180,000 Sub-code 4: 240,000/240,000
1158-0 to 8
1159
1172-0 to 8
1173
1174-0 to 8
1175
Needle electrode
1182-0 to 8
1183
Ozone filter
1198-0 to 8
1199
Developer material
1200-0 to 8
1201
1214-0 to 8
1215
1224-0 to 8
1225
Fuser roller
1246-0 to 8
1247
Pressure roller
1250-0 to 8
1251
2 - 116
Remarks <Default values of code 1266 (e-STUDIO230/280)> Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0 Sub-code 1: 148,000/180,000 Sub-code 4: 240,000/240,000 <Default values of code 1268 (e-STUDIO230/280)> Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0 Sub-code 1: 148,000/180,000 Sub-code 4: 240,000/240,000 <Default values of code 1282 (e-STUDIO230/280)> Sub-codes 0, 2, 8: 0/0 Sub-code 1: 120,000/120,000 <Default values of code 1284 (e-STUDIO230/280)> Sub-codes 0, 2, 8: 0/0 Sub-code 1: 120,000/120,000 <Default values of code 1286 (e-STUDIO230/280)> Sub-codes 0, 2, 8: 0/0 Sub-code 1: 120,000/120,000 <Default values of code 1290 (e-STUDIO230/280)> Sub-codes 0, 2, 8: 0/0 Sub-code 1: 80,000/80,000 <Default values of code 1292 (e-STUDIO230/280)> Sub-codes 0, 2, 8: 0/0 Sub-code 1: 80,000/80,000 <Default values of code 1294 (e-STUDIO230/280)> Sub-codes 0, 2, 8: 0/0 Sub-code 1: 80,000/80,000 <Default values of code 1298 (e-STUDIO230/280)> Sub-codes 0, 2, 8: 0/0 Sub-code 1: 80,000/80,000 <Default values of code 1300 (e-STUDIO230/280)> Sub-codes 0, 2, 8: 0/0 Sub-code 1: 80,000/80,000 <Default values of code 1302 (e-STUDIO230/280)> Sub-codes 0, 2, 8: 0/0 Sub-code 1: 160,000/160,000 <Default values of code 1306 (e-STUDIO230/280)> Sub-codes 0, 2, 8: 0/0 Sub-code 1: 80,000/80,000 <Default values of code 1308 (e-STUDIO230/280)> Sub-codes 0, 2, 8: 0/0 Sub-code 1: 80,000/80,000
1268-0 to 8
1269
1282-0,1,2,8
1283
1284-0,1,2,8
1285
1286-0,1,2,8
1287
1290-0,1,2,8
1291
1292-0,1,2,8
1293
1294-0,1,2,8
1295
1298-0,1,2,8
1299
1300-0,1,2,8
1301
1302-0,1,2,8
1303
1306-0,1,2,8
1307
1308-0,1,2,8
1309
2 - 117
Remarks <Default values of code 1310 (e-STUDIO230/280)> Sub-codes 0, 2, 8: 0/0 Sub-code 1: 160,000/160,000 <Default values of code 1312 (e-STUDIO230/280)> Sub-codes 0, 2, 8: 0/0 Sub-code 1: 80,000/80,000 <Default values of code 1314 (e-STUDIO230/280)> Sub-codes 0, 2, 8: 0/0 Sub-code 1: 80,000/80,000 <Default values of code 1316 (e-STUDIO230/280)> Sub-codes 0, 2, 8: 0/0 Sub-code 1: 80,000/80,000 <Default values of code 1320 (e-STUDIO230/280)> Sub-codes 0, 2, 8: 0/0 Sub-code 1: 80,000/80,000 <Default values of code 1322 (e-STUDIO230/280)> Sub-codes 0, 2, 8: 0/0 Sub-code 1: 80,000/80,000 <Default values of code 1324 (e-STUDIO230/280> Sub-codes 0, 2, 8: 0/0 Sub-code 1: 80,000/80,000 <Default values of code 1328 (e-STUDIO230/280)> Sub-codes 0, 2, 8: 0/0 Sub-code 1: 80,000/80,000 <Default values of code 1330 (e-STUDIO230/280)> Sub-codes 0, 2, 8: 0/0 Sub-code 1: 80,000/80,000 <Default values of code 1332 (e-STUDIO230/280)> Sub-codes 0, 2, 8: 0/0 Sub-code 1: 80,000/80,000 <Default values of code 1336 (e-STUDIO230/280)> Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0 Sub-code 1: 120,000/120,000 Sub-code 4: 74,000/90,000
1312-0,1,2,8
1313
1314-0,1,2,8
1315
1316-0,1,2,8
1317
1320-0,1,2,8
1321
1322-0,1,2,8
1323
1324-0,1,2,8
1325
1328-0,1,2,8
1329
1330-0,1,2,8
1331
1332-0,1,2,8
1333
Recovery blade
1336-0 to 8
1337
2 - 118
<<Procedure to copy the total counter value (08-257)>> (1) (2) Turn ON the power while [0] and [8] are pressed simultaneously. Key in the code 257 with the digital keys and press the [START] button (the following is displayed). Note: Before performing the following operations, note the current counter values.
Fig.2-3
(3)
Key in the value 1 or 2 with the digital key and press the [START] button. The value entered is displayed on the left of the %, and the [ENTER] button is displayed. Note: The value can be erased by pressing the [CLEAR] button to change as long as the [START] button is not pressed. (The value on the left of the % is reset to 0 by pressing the [CLEAR] button.) Key in 1 to copy the value of the total counter (LGC board) (A) onto the value of the backup counter (SYS board) (B).
(A)
(B)
Fig.2-4
2 - 119
Key in 2 to copy the value of the backup counter (SYS board) (B) onto the value of the total counter (LGC board) (A).
(A)
(B)
Fig.2-5
(4)
Note: The screen returns to the code entry screen without copying (overwriting) the value when the [CANCEL] button is pressed.
2 - 120