Académique Documents
Professionnel Documents
Culture Documents
SERVICE MANUAL
COLOR TELEVISION/VIDEO CASSETTE RECORDER/ DVD VIDEO PLAYER
S C
6. AVOID AN X-RAY
Safety is secured against an X-ray by considering about the cathode-ray tube and the high voltage peripheral circuit, etc. Therefore, when repairing the high voltage peripheral circuit, use the designated parts and make sure not modify the circuit. Repairing except indicates causes rising of high voltage, and it emits an X-ray from the cathoderay tube.
4. PUT PARTS AND WIRES IN THE ORIGINAL POSITION AFTER ASSEMBLING OR WIRING
There are parts which use the insulation material such as a tube or tape for safety, or which are assembled in the condition that these do not contact with the printed board. The inside wiring is designed not to get closer to the pyrogenic parts and high voltage parts. Therefore, put these parts in the original positions.
1. Unplug the plug from the AC outlet. 2. Remove the antenna terminal on TV and turn on the TV. 3. Insulation resistance between the cord plug terminals and the eternal exposure metal [Note 2] should be more than 1M ohm by using the 500V insulation resistance meter [Note 1]. 4. If the insulation resistance is less than 1M ohm, the inspection repair should be required.
[Note 1]
If you have not the 500V insulation resistance meter, use a Tester.
[Note 2]
A1-1
Fig. 1
PREPARATION OF SERVICING
The laser diode used for a pickup head may be destroyed with external static electricity. Moreover, even if it is operating normally after repair when static electricity discharge is received at the time of repair, the life of the product may be shortened. Please perform the following measure against static electricity, be careful of destruction of a laser diode at the time of repair. Place the unit on a workstation equipped to protect against static electricity, such as conductive mat. Soldering iron with ground wire or ceramic type is used. A worker needs to use a ground conductive wrist strap for body.
A1-2
Fig. 1
Fig. 2
Fig. 1
A1-3
TABLE OF CONTENTS
SERVICING NOTICES ON CHECKING .................................................................................. HOW TO ORDER PARTS ....................................................................................................... WHEN REPLACING DVD DECK ............................................................................................ PREPARATION OF SERVICING ............................................................................................ TAPE REMOVAL METHOD AT NO POWER SUPPLY ......................................................... DISC REMOVAL METHOD AT NO POWER SUPPLY .......................................................... PARENTAL CONTROL-RATING LEVEL ............................................................................... TABLE OF CONTENTS ........................................................................................................... GENERAL SPECIFICATIONS ................................................................................................. DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF MECHANICAL PARTS AND P. C. BOARDS ......................................... 2. REMOVAL OF VCR DECK PARTS ................................................................................ 3. REMOVAL OF DVD DECK PARTS ................................................................................ 4. REMOVAL OF ANODE CAP ........................................................................................... 5. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC ............................................ KEY TO ABBREVIATIONS ..................................................................................................... SERVICE MODE LIST ............................................................................................................. PREVENTIVE CHECKS AND SERVICE INTERVALS ........................................................... WHEN REPLACING EEPROM (MEMORY) IC ...................................................................... SERVICING FIXTURES AND TOOLS .................................................................................... PREPARATION FOR SERVICING .......................................................................................... MECHANICAL ADJUSTMENTS ............................................................................................. ELECTRICAL ADJUSTMENTS ............................................................................................... BLOCK DIAGRAMS DVD ....................................................................................................................................... Y/C/AUDIO/HEAD AMP ....................................................................................................... MICON .................................................................................................................................. IN/OUT .................................................................................................................................. CHROMA/IF .......................................................................................................................... SOUND AMP/SURROUND .................................................................................................. Hi-Fi/DEMODULATOR ......................................................................................................... DIGITAL COMB FILTER ...................................................................................................... DVD IN/OUT ......................................................................................................................... REGULATOR ....................................................................................................................... TV ......................................................................................................................................... PRINTED CIRCUIT BOARDS DVD ....................................................................................................................................... VCR ....................................................................................................................................... DEFLECTION/CRT/OPERATION ........................................................................................ SCHEMATIC DIAGRAMS MPEG/MICON/DSP .............................................................................................................. MEMORY .............................................................................................................................. MOTOR DRIVE .................................................................................................................... AUDIO/VIDEO ...................................................................................................................... Y/C/AUDIO/HEAD AMP ....................................................................................................... MICON .................................................................................................................................. IN/OUT .................................................................................................................................. CHROMA/IF .......................................................................................................................... SOUND AMP/SURROUND .................................................................................................. Hi-Fi/DEMODULATOR ......................................................................................................... DIGITAL COMB FILTER ...................................................................................................... DVD IN/OUT ......................................................................................................................... REGULATOR ........................................................................................................................ TV POWER .......................................................................................................................... DEFLECTION ....................................................................................................................... CRT/OPERATION ................................................................................................................ INTERCONNECTION DIAGRAM ............................................................................................ WAVEFORMS .......................................................................................................................... MECHANICAL EXPLODED VIEWS ........................................................................................ CHASSIS EXPLODED VIEWS ................................................................................................ DVD DECK EXPLODED VIEWS ............................................................................................. MECHANICAL REPLACEMENT PARTS LIST ...................................................................... CHASSIS REPLACEMENT PARTS LIST ............................................................................... DVD DECK REPLACEMENT PARTS LIST ............................................................................ ELECTRICAL REPLACEMENT PARTS LIST ........................................................................ A1-1 A1-1 A1-2 A1-2 A1-3 A1-3 A1-3 A2-1 A3-1~A3-6 B1-1~B1-3 B2-1~B2-6 B3-1~B3-3 B4-1 B5-1, B5-2 C1-1, C1-2 C2-1 C3-1, C3-2 C4-1 D1-1 D1-1 D2-1~D2-4 D3-1~D3-6 E-1, E-2 E-3, E-4 E-5, E-6 E-7, E-8 E-9, E-10 E-11, E-12 E-13, E-14 E-15, E-16 E-17, E-18 E-19, E-20 E-21, E-22 F-1, F-2 F-3~F-6 F-7, F-8 G-1, G-2 G-3, G-4 G-5, G-6 G-7, G-8 G-9, G-10 G-11, G-12 G-13, G-14 G-15, G-16 G-17, G-18 G-19, G-20 G-21, G-22 G-23, G-24 G-25, G-26 G-27, G-28 G-29, G-30 G-31, G-32 G-33, G-34 H-1~H-3 I1-1, I1-2 I2-1, I2-2 I3-1 J1-1 J2-1 J3-1 J4-1~J4-3
A2-1
GENERAL SPECIFICATIONS
G-1 TV System CRT CRT Size / Visual Size CRT Type Magnetic Field BV/BH 20 inch / 508.0mmV Flat +0.45G / 0.18G NTSC 2 Speaker Front 1.8 x 3.9 Inch 8 ohm 1.5W + 1.5W __ VHS Player / Recorder NTSC Yes OVD-7 4 Heads 2 Heads Mono /Yes Yes SP/SLP SP/LP/SLP FF:1'48"/REW:1'48" T-120 SP/LP/SLP=3x,5x/7x,9x/9x,15x Yes 1/10 NTSC DVD, CD-DA, CD-R/RW DVD-R/RW (Video Format Only) 120 mm , 80 mm DM3PA 4 step 2-45 times(DVD) 4-40 times (CD) 4 step 2-45 times(DVD) 4-40 times (CD) Fwd 1/7 - 1/2 times -Rev --US System M 1 Tuner US(w/CABLE) 2~69, 4A, A-5~A-1, A~I, J~W, W+1~W+84 45.75MHz 41.25MHz 4.5MHz No US-Stereo Yes 1 V p-p/75 ohm 1 V p-p/75 ohm 65dB 50dB 400 Lines 220 Lines -8.0dBm/50k ohm -8.0dBm/1k ohm -12.0dBm/1k ohm 0.5 V p-p/75 ohm(DVD) 90 dB 38 dB 0.06% (1kHz) 1.5% (1kHz) Typical 4Hz - 22kHz 4Hz - 20kHz 100Hz - 10kHz
Sound Output G-2 VCR System System Video System Hi-Fi STEREO NTSC PB Deck Heads Video Head FM Audio Head
Audio /Control Erase(Full Track Erase) Tape Rec PAL Speed NTSC Play PAL NTSC Fast Forward / Rewind Time (Approx.) at 25oC with Cassette Forward/Reverse Picture Search Frame Advance Slow Speed Color System Disc Disc Diameter Drive Search speed NTSC or PAL-M
G-3
DVD System
Slow speed Actual Actual G-4 Tuning System Broadcasting System Tuner and Receive CH Intermediate Frequency Preset CH Stereo/Dual TV Sound Tuner Sound Muting Video Signal System Destination CH Coverage Picture(FP) Sound(FS) FP-FS
G-5
Sig n al
Input Level Output Level S/N Ratio (Weighted) at DVD Mode S/N Ratio (Weighted) at VCR Mode Horizontal Resolution at DVD Mode Horizontal Resolution at VCR(SP)Mode Output Level Input Level Output Level(0dB=0.775Vrms) Output Level(-20dBFs 0dBFs=2.0Vrms) Digital Output Level S/N Ratio at DVD (Weighted) S/N Ratio at VCR (SP)(CCIR Filter:ON) Harmonic Distortion at DVD Mode Harmonic Distortion at VCR(SP) Mode Frequency Response : DVD Mode at DVD at Video CD at SVCD at CD VCR Mode at SP
A3-1
GENERAL SPECIFICATIONS
at LP at SLP Hi-Fi Audio Signal Dynamic Range : More than Frequency Response : Wow And Flutter : Less than Channel Separation : More than Harmonic Distortion : Less than AC DC at AC at DC Stand by (at AC) Per Year Power Fuse Safety Circuit IC Protector(Micro Fuse) Dew Sensor Safety Radiation X-Radiation Laser Operation Storage Menu Menu System Setup 100Hz - 6kHz 100Hz - 4kHz 90 dB 20Hz - 20kHz 0.01 %Wrms 60 dB 1.0 % 120V,60Hz 110 W at 120 V 60 Hz 4 W at 120 V 60 Hz Yes Yes No No UL FCC DHHS DHHS +5oC ~ +40oC -20oC ~ +60oC Less than 80% RH Yes Icon Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Icon Yes Yes Yes Yes No
G-6
Power
Protector
G-7
Regulation
Type Clock Set On/Off Timer Set Auto Clock On/Off Standard Time Daylight Saving Time
TV Setup Language Picture Audio Picture Preference Channel Setup TV/CABLE Auto CH Memory Add/ Delete V-chip Setup Tape Setup Timer Rec Set Auto Repeat On/Off G-CODE(or SHOWVIEW or PLUSCODE)No. Entry Clock / Date TV/VCR DVD CH/AV(LINE) Tape Counter(Linear Counter) Tape Speed Sleep Time Stereo/Audio Output Bilingual SAP Control Volume Level Brightness/Contrast/Sharpness/Color Tint Bass/Treble/Balance Manual Tracking Play/Stop/FF/Rew/Rec/OTR/T-Rec/Pause/Eject/Tape In (Symbol Mark) Auto Tracking/Manual Tracking Caption / Text Index Mute Hi-Fi Repeat Zero Return DEW Menu (DVD) Menu Type Language Menu Subtitle Audio OSD Language(Set up Language)
G-11
A3-2
GENERAL SPECIFICATIONS
Video E.B.L. (Enhanced Black Level) TV Screen Size(4:3) OSD Display On/Off Picture Mode (Video/Film/Auto) JPEG Interval Audio DRC (Dynamic Range Control) Dialogue (On DRC[TV] / Off DRC[Std]) Surround System Disc/Card Slot Password Lock/ Un Lock Parental Select Files HDMI (480p/1080i/720p) Output Open Close No Disc Reading Disc Play Still/Pause Stop Prohibit Mark PBC Step Skip(>>|) Skip(|<<) Random Repeat Slow+ SlowSearch+ SearchJump Resume Title No. Chapter No. Track No. Time Sub Title No. Angle No. Vocal On/Off Audio No. Audio Stereo L/R Zoom Marker No. Program Play Back Surround On/Off Screen Saver MP3, WMA, JPEG Yes No Yes Yes Yes Yes Yes Yes No No Yes No Yes Yes Yes No No Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes (CD,MP3,WMA,JPEG) Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes No Yes No Yes (CD, MP3, WMA, JPEG) No No Yes Yes Yes Yes (MP3,WMA Only) Yes English French Spanish 1990/1/1 ~ 2081/12/31 8 Program/ 1 Month 6 Hours 120 Min 10 Min 1 Program 15 Min Min 5 Sec RC-HH No ORION NEC 71-8E 3V UM-4 x 2 pcs 52 Yes Yes Yes
G-12 G-13
G-14
Calendar Timer Events One Touch Recording Max Time Sleep Timer Max Time Step On/Off Timer Program(On Timer / Off Timer) Auto Shut Off No Signal No Operation Timer Back-up (at Power Off Mode) Unit Glow in Dark Remocon Remocon Format Format Custom Code Power Source Voltage(D.C) UM size x pcs Total Keys Keys TV/VCR DVD Power
A3-3
GENERAL SPECIFICATIONS
1 2 3 4 5 6 7 8 9 0 ChannelChannel+ VolumeVolume+ Display (Call) Sleep Audio Select Mute Index- / SkipIndex+ / Skip+ T-REC Rec/OTR Slow+ Play Stop Rew / SearchF. Fwd / Search+ Pause / Still CM Skip Speed / Return Counter Reset / Angle Zero Return / Subtitle Input Select / Zoom Menu /Set Up Program / Repeat A-B ATR / Top Menu Tracking+ / DVD Menu Tracking- / Play Mode Cancel 3D Surround Cursor Up Cursor Down Cursor Left Cursor Right Enter Eject Open/Close TV Monitor Closed Caption Quick View / Jump CABLE WIDE Position G-15 Features (TV/VCR) Auto Head Cleaning VIDEO PLUS+(SHOWVIEW,G-CODE) Auto Clock Picture Preference Auto Setup Forward / Reverse Picture Search Auto CH Memory Surround Stable Sound Closed Caption TV Auto Shut off Function End Call Index Search SQPB CABLE CM Skip(30sec x 6 Times) Comb Filter (2Lines) VM Circuit TV Monitor Program Extend Choke Coil Energy Star Protect of FBT Leak Circuit Zero Return Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No No No Yes No Yes Yes No Yes Yes Yes Yes Yes Yes No Yes No Yes Yes Yes No Yes No No No Yes Yes
A3-4
GENERAL SPECIFICATIONS
Power On Memory V-chip USA V-chip CANADA V-chip Tray Lock Auto Stop (Pause, and Resume Stop after 5min.) Card Slot Reading (Not secured Data) xD-Picture Card Memory Stick Multi Media Card SD Memory Card Compact Flash Micro Drive SmartMedia Video CD Playback SVCD Playback MP3 Playback WMA Playback JPEG Playback Digital Out (Dolby Digital) (MPEG) (PCM) (DTS) Down Mix Out (Dolby Digital) (DTS) 3D Surround Screen Saver Audio DAC Copy (Disc to Tape) Owner's Manual Remote Control Unit Battery UM size x pcs OEM Brand Rod Antenna Poles Terminal Loop Antenna Terminal U/V Mixer 300 ohm to 75 ohm Antenna Adapter Antenna Change Plug DC Car Cord (Center+) AC Plug Adapter AC Cord AV Cord (2Pin-1Pin) Guarantee Card Registration Card ESP Card Warning Sheet Dew/AHC Caution Sheet Quick Set-up Sheet Circuit Diagram Service Facility List Important Safeguard Sheet Information (Return) Switch Front Power (Tact) Channel Up Channel Down Volume Up Volume Down Play (VCR) Stop / Eject (VCR) F.FWD/Cue (VCR) Rew/Rev (VCR) REC/OTR (VCR) Play (DVD) Stop (DVD) Skip+ /Search+ (DVD) Skip- /Search- (DVD) Open/Close (DVD) Input Select Main Power SW Indicator Power REC/OTR T-REC TV/VCR No No No No No No No Yes No No No No No No No No No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No No Yes(Red) Yes(Red) Yes(Red) No No No Yes No No Yes No No No No No No No No No No Yes Yes Yes Yes Yes Yes Yes Yes No No No 192kHz / 24bit No Language w/Guarantee Card English / Spanish No Yes No No
Features (DVD)
G-16
Accessories
G-17
Interface
A3-5
GENERAL SPECIFICATIONS
Terminals Front DVD Video Input Audio Input 4 in 1 Card Slot Compact Flash Card Slot Other Terminal Video Input Audio Input Video Output Audio Output Digital Audio Output VHF/UHF Antenna Input AC Inlet Approx. W x D x H (mm) Net (Approx.) Gross (Approx.) No RCA x 1 RCA x 2(Stereo) No No HeadPhone (Stereo & Mono, 3.5mm) RCA x 1 RCA x 2(Stereo) RCA x1 RCA x 2(Stereo) Coaxial (DVD Only) F Type No 573 x 485 x 517 27.0kg (59.5lbs) 30.5kg (67.3lbs) No Double/Brown 658 x 575 x 625 Yes 1 Corner / 3 Edges / 6 Surfaces 31 216 Sets PS 94V0 DECABROM PS 94V0 DECABROM No Yes No No
Rear
G-21
Material
G-22
Environment
Content Material Dimensions W x D x H(mm) Description of Origin Gift Box Material Dimensions W x D x H(mm) Description of Origin Drop Test Natural Dropping At Height (cm) Container Stuffing(40' container) Cabinet Front Rear Jack Panel PCB Non-Halogen Demand Eyelet Demand Environmental standard requirement (by buyer) Pb-free
A3-6
DISASSEMBLY INSTRUCTIONS
1. REMOVAL OF MECHANICAL PARTS AND P.C. BOARDS
1-1: BACK CABINET (Refer to Fig. 1-1) 1. Remove the 6 screws (1). 2. Remove the 2 screws (2). 3. Remove the Back Cabinet in the direction of arrow. 1-3: TV/DVD/VCR BLOCK (Refer to Fig. 1-3) 1. Remove the 2 screws (1). 2. Disconnect the following connectors: (CP303, CP404 and CP1704). 3. Remove the TV/DVD/VCR Block in the direction of arrow.
Front Cabinet Front Cabinet
(1) (1)
(1)
TV/DVD/VCR Block
(1)
(1)
Fig. 1-3
(1) (1) (2) (2) (1)
Back Cabinet
1-4: VCR DECK (Refer to Fig. 1-4) NOTE Fig. 1-1 Do not remove the cable at the FE Head section. The FE Head may be damaged if you remove the cable by force. Remove the 2 screws (1). Remove the VCR Top. Move the Cassette Holder Ass'y to the back side. Remove the 3 screws (2). Remove the 2 screws (3). Remove the Deck Shield Cover. Remove the screw (4). Remove the FE Head. Disconnect the following connectors: (CP101, CP4501 and CP4502). 10. Remove the VCR Deck in the direction of arrow. 1. 2. 3. 4. 5. 6. 7. 8. 9.
(2) (3)
Deck Shield Cover CRT PCB
1-2: CRT PCB (Refer to Fig. 1-2) CAUTION: BEFORE REMOVING THE ANODE CAP, DISCHARGE ELECTRICITY BECAUSE IT CONTAINS HIGH VOLTAGE. BEFORE ATTEMPTING TO REMOVE OR REPAIR ANY PCB, UNPLUG THE POWER CORD FROM THE AC SOURCE. 1. Remove the Anode Cap. (Refer to REMOVAL OF ANODE CAP) 2. Disconnect the following connectors: (CP603B, CP803 and CP805). 3. Remove the CRT PCB in the direction of arrow.
(4)
FE Head
Front Cabinet
VCR Deck
(1) (1)
VCR Top Bottom Plate
B1-1
DISASSEMBLY INSTRUCTIONS
1-5: VCR PCB (Refer to Fig. 1-5) 1. Remove the 6 screws (1). 2. Remove the screw (2). 3. Remove the AV Jack Shield. 4. Disconnect the following connectors: (CP001, CP602B, CP604, CP2201, CP8001 and CP8002). 5. Remove the VCR PCB in the direction of arrow.
(1) (1) (1)
1-7: DVD PCB/DVD DECK (Refer to Fig. 1-7) 1. Short circuit the position shown in Fig. 1-7 using a soldering iron. If you remove the DVD Deck with no soldering, the Laser may be damaged. 2. Remove the 4 screws (1). 3. Remove the DVD Top in the direction of arrow (A). 4. Remove the 2 screws (2). 5. Remove the DVD PCB in the direction of arrow (B). 6. Disconnect the following connectors: (CP2301, CP2302 and CP2303). 7. Remove the 4 screws (3). 8. Remove the DVD Deck in the direction of arrow (C).
(1)
(1)
DVD Top
(1)
(2)
Bottom Plate
Fig. 1-5 1-6: VCR DECK (Refer to Fig. 1-6) 1. Remove the 4 screws (1). 2. Remove the DVD Block in the direction of arrow (A). 3. Remove the 2 screws (2). 4. Remove the Operation PCB in the direction of arrow (B).
(1) (1) (1)
DVD Block DVD Deck
(B)
(3) (3)
(3)
(3)
(C) Angle Deck Pick Up PCB Short circuit using a soldering iron.
Fig. 1-7 NOTE 1. Before your operation, please read PREPARATION OF SERVICING. 2. Use the Lead Free solder. 3. Manual soldering conditions Soldering temperature: 320 20C Soldering time: Within 3 seconds Soldering combination: Sn-3.0Ag-0.5Cu 4. When Soldering/Removing of solder, use the drawing equipment over the Pick Up Unit to keep the Flux smoke away from it. 5. When installing the DVD Deck, remove all the soldering on the short circuit position after the connection of Pick Up PCB and DVD PCB connector.
(1)
(A)
(2) (2)
(B) Operation PCB Bottom Plate
Fig. 1-6
B1-2
DISASSEMBLY INSTRUCTIONS
1-8: DEFLECTION PCB (Refer to Fig. 1-8) 1. Remove the 2 screws (1). 2. Remove the 3 screws (2). 3. Remove the Deflection PCB in the direction of arrow.
(2) (2) (1) (1) (2)
Deflection PCB
Bottom Plate
Fig. 1-8
B1-3
DISASSEMBLY INSTRUCTIONS
2. REMOVAL OF VCR DECK PARTS
2-1: TOP BRACKET (Refer to Fig. 2-1) 1. Extend the 2 supports 1. 2. Slide the 2 supports 2 and remove the Top Bracket. NOTE 1. After installation of the Top Bracket, bend the support 1 so that the Top Bracket is fixed.
Top Bracket Flap Lever
2-4: LINK LEVER/FLAP LEVER (Refer to Fig. 2-4) 1. Extend the support 1. 2. Remove the Link Lever. 3. Remove the Flap Lever.
1
Link Lever
Top Bracket
2 2
Main Chassis
Main Chassis
Fig. 2-1 2-2: CASSETTE HOLDER ASS'Y (Refer to Fig. 2-2) 1. Move the Cassette Holder Ass'y to the front side. 2. Push the Locker R to remove the Cassette Side R. 3. Remove the Cassette Side L.
Cassette Side R Main Chassis Locker R
1. Remove the screw 1. 2. Remove the Loading Motor. 3. Remove the Worm.
Loading Motor
Fig. 2-5-A
NOTE 1. In case of the Worm installation, check if the value of the Fig. 2-5-B is correct. 2. In case of the Loading Motor installation, hook the wire on the Cassette Opener as shown Fig. 2-5-C. 3. When installing the wires between Capstan DD Unit and Loading Motor, connect them correctly as shown Fig. 2-5-D.
Fig. 2-2 2-3: LINK UNIT (Refer to Fig. 2-3) 1. Set the Link Unit to the Eject position. 2. Unlock the support 1. 3. Remove the (A) side of the Link Unit first, then remove the (B) side.
Main Chassis
19.2 0.1mm
Link Unit
(A)
1
Main Chassis
Fig. 2-5-B
Fig. 2-3
B2-1
DISASSEMBLY INSTRUCTIONS
NOTE
Slacken the wire.
1. In case of the Tension Band installation, note the direction of the installation. (Refer to Fig. 2-6-C) 2. In case of the Tension Band installation, install correctly as Fig. 2-6-D. 3. In case of the Tension Connect installation, install as the circled section of Fig. 2-6-E.
Loading Motor
Fig. 2-5-C
Pink Loading Motor Capstan DD Unit L2
L1
White
Fig. 2-6-D 2-6: TENSION ASS'Y (Refer to Fig. 2-6-B) 1. Turn the Pinch Roller Cam clockwise so that the Tension Holder hook is set to the position of Fig. 2-6-A to move the Tension Arm Ass'y. 2. Remove the Tension Spring. 3. Unlock the 2 supports 1 and remove the Tension Band. 4. Unlock the support 2 and remove the Tension Arm Ass'y. 5. Unlock the support 3 and remove the Tension Connect. 6. Float the hook 4 and turn it clockwise then remove the Tension Holder.
Tension Arm Ass'y Tension Connect
Main Chassis
Fig. 2-6-E
2-7: T BRAKE ARM/T BRAKE BAND (Refer to Fig. 2-7-A) 1. Remove the T Brake Spring. 2. Turn the T Brake Arm clockwise and bend the hook section to remove it. 3. Unlock the 2 supports 1 and remove the T Brake Band.
T Brake Band
Fig. 2-6-A
1 1
Tension Connect
1
Tension Band
1 3
2 4
Fig. 2-7-A
Fig. 2-6-B
B2-2
DISASSEMBLY INSTRUCTIONS
NOTE 1. In case of the T Brake Band installation, install correctly as Fig. 2-7-B. [OK]
T Brake Band T Brake Arm
NOTE 1. In case of the S Reel and T Reel installation, check if the correct parts are installed. (Refer to Fig. 2-8-B) 2. In case of the Idler Arm Ass'y installation, install correctly as Fig. 2-8-C. And also set it so that the section "B" of Fig. 2-8-A is placed under the Main Chassis tab.
[NG]
T Brake Band
T Brake Arm
Fig. 2-7-B 2-8: S REEL/T REEL/IDLER ARM ASS'Y/IDLER GEAR (Refer to Fig. 2-8-A) 1. Remove the S Reel and T Reel. 2. Remove the 2 Polyslider Washers 1. 3. Remove the Idler Arm Ass'y and Idler Gear. NOTE 1. Take care not to damage the gears of the S Reel and T Reel. 2. The Polyslider Washer may remain on the back of the reel. 3. Take care not to damage the shaft. 4. Do not touch section "A" of S Reel and T Reel. (Use gloves.) (Refer to Fig. 2-8-A) Touching may leave stains on section "A" 5. When you install the reel, clean the shaft and grease it (FG-84M) . (If you do not grease, noise may be heard in FF/REW mode.) 6. After installing the reel, adjust the height of the reel. (Refer to MECHANICAL ADJUSTMENT) [NG]
Idler Arm Ass'y Clutch Gear
Fig. 2-8-B
[OK]
Clutch Gear Idler Arm Ass'y
Fig. 2-8-C 2-9: CASSETTE OPENER/PINCH ROLLER BLOCK/ P5 ARM ASS'Y (Refer to Fig. 2-9-A) 1. Unlock the support 1 and remove the Cassette Opener. 2. Remove the Pinch Roller Block and P5 Arm Ass'y.
1
Cassette Opener
Idler Gear Idler Arm Ass'y S Reel (B) P5 Arm Ass'y (A) T Reel Main Chassis Pinch Roller Block
1
(A)
Fig. 2-9-A NOTE 1. Do not touch the Pinch Roller. (Use gloves.) 2. In case of the Pinch Roller Block and the Pinch Roller Cam installation, install correctly as Fig. 2-9-B. Fig. 2-8-A
Pinch Roller Block Can be seen the hole of the Pinch Roller Cam.
P5 Arm Ass'y
Fig. 2-9-B
B2-3
DISASSEMBLY INSTRUCTIONS
2-10: A/C HEAD (Refer to Fig. 2-10-A) 1. 2. 3. 4. Remove the screw 1. Remove the A/C Head Base. Remove the 3 screws 2. Remove the A/C Head and A/C Head Spring. 2-12: AHC ASS'Y/CYLINDER UNIT ASS'Y (Refer to Fig. 2-12) 1. Unlock the support 1 and remove the AHC Ass'y. 2. Disconnect the following connector: (CD2001) 3. Remove the 3 screws 2. 4. Remove the Cylinder Unit Ass'y. NOTE 1. When you install the Cylinder Unit Ass'y, tighten the screws from (1) to (3) in order while pulling the Ass'y toward the left front direction.
NOTE 1. Do not touch the A/C Head. (Use gloves.) 2. When you install the A/C Head Spring, install as shown in Fig. 2-10-B. 3. When you install the A/C Head, tighten the screw (1) first, then tighten the screw (2), finally tighten the screw (3).
(1) (3)
2 2
(2)
A/C Head
1
A/C Head Base Screw Torque: 5 0.5kgfcm
Fig. 2-10-A
(1)
(3) (2)
2 2
2
Screw Torque: 3 0.5kgfcm
Fig. 2-12
2-13: CAPSTAN DD UNIT (Refer to Fig. 2-13) 1. 2. 3. 4. 5. Remove the Capstan Belt. Remove the screw 1. Remove the Capstan Holder. Remove the 3 screws 2. Remove the Capstan DD Unit.
Spring Position
Fig. 2-10-B
2-11: FE HEAD (RECORDER ONLY) (Refer to Fig. 2-11) 1. Remove the screw 1. 2. Remove the FE Head.
Capstan Belt
1
FE Head
1
Capstan Holder Capstan DD Unit
Screw Torque: 5 0.5kgfcm The FE Head is not installed on the Video Cassette Player.
Fig. 2-11
2
Screw Torque: 4 0.5kgfcm
22
Fig. 2-13
B2-4
DISASSEMBLY INSTRUCTIONS
2-14: MAIN CAM/PINCH ROLLER CAM/JOINT GEAR (Refer to Fig. 2-14-A) 1. Remove the E-Ring 1, then remove the Main Cam. 2. Remove the E-Ring 2, then remove the Pinch Roller Cam and Joint Gear.
1
Main Cam Main Loading Gear Marker
NOTE 1. When you install the Loading Arm S Unit, Loading Arm T Unit and Main Loading Gear, align each marker. (Refer to Fig. 2-15-B)
Marker
2
Pinch Roller Cam
Joint Gear
Fig. 2-15-B Fig. 2-14-A NOTE 1. In case of the Pinch Roller Cam and Main Cam installation, install them as shown in the circled section of Fig. 2-15-B so that the markers meet. (Refer to Fig. 2-14-B) And also can be seen the Main Chassis hole through the Main Cam maker hole. 2-16: CLUTCH ASS'Y/RING SPRING/CLUTCH LEVER/ CLUTCH GEAR (Refer to Fig. 2-16-A) 1. 2. 3. 4. Remove the Polyslider Washer 1. Remove the Clutch Ass'y and Ring Spring. Remove the Clutch Lever. Remove the Coupling Gear, Coupling Spring and Clutch Gear.
1
Clutch Ass'y
Ring Spring
Clutch Lever
Fig. 2-14-B 2-15: LOADING GEAR S/T UNIT (Refer to Fig. 2-15-A) 1. Remove the E-Ring 1 and remove the Main Loading Gear. 2. Remove the Main Rod, Tension Lever, Loading Arm S Unit and Loading Arm T Unit.
1
Main Rod Main Loading Gear
Fig. 2-16-A
Fig. 2-15-A
B2-5
DISASSEMBLY INSTRUCTIONS
NOTE 1. In case of the Clutch Ass'y installation, install it with inserting the spring of the Clutch Ass'y into the dent of the Coupling Gear. (Refer to Fig. 2-16-B) NOTE 1. Do not touch the roller of Guide Roller. 2. In case of the P4 Cap installation, install it with parallel for "A" and "B" of Fig. 2-17-B. 3. In case of the Cassette Guide Post installation, install correctly as the circled section of Fig. 2-17-C.
"A" "B"
Clutch Ass'y
Coupling Gear
Fig. 2-16-B 2-17: CASSETTE GUIDE POST/INCLINED BASE S/T UNIT/P4 CAP/LED REFLECTOR (Refer to Fig. 2-17-A) 1. Remove the P4 Cap. 2. Unlock the support 1 and remove the Cassette Guide Post. 3. Remove the Inclined Base S/T Unit. 4. Remove the screw 2. 5. Remove the LED Reflector.
Cassette Guide Post
P4 Cap
Cassette Opener
1
Inclined Base S Unit
[NG]
Cassette Guide Post Inclined Base T Unit
P4 Cap
Fig. 2-17-C
LED Reflector
Fig. 2-17-A
B2-6
DISASSEMBLY INSTRUCTIONS
3. REMOVAL OF DVD DECK PARTS
NOTE 1. Disassemble only the DVD DECK PARTS parts listed here. Minute adjustments are needed if the disassembly is done. If the repair is needed except listed parts, replace the DVD MECHA ASS'Y. 3-1: TRAY (Refer to Fig. 3-1-A) 1. Set the Tray opened. (Refer to the DISC REMOVAL METHOD AT NO POWER SUPPLY) 2. Unlock the 2 supports 1 and remove the Tray.
Main Frame Ass'y (3) Traverse Holder (3) Rack Loading (3)
NOTE 1. In case of the Main Chassis Ass'y, install it from (1) to (4) in order. (Refer to Fig. 3-2-B) 2. In case of the Main Chassis Ass'y installation, hook the wire on the Main Frame Ass'y as shown Fig. 3-2-C.
Main Frame Ass'y (Bottom Side)
(2)
1
Tray
1
(4) (4)
Fig. 3-1-A NOTE 1. In case of the Tray installation, install them as the circled section of Fig. 3-1-B so that the each markers are met.
Main Frame Ass'y
Check Lock
Fig. 3-2-B
Check Hook
Fig. 3-2-C
3-3: LOADING MOTOR PCB ASS'Y/ LOADING BELT (Refer to Fig. 3-3-A) 1. 2. 3. 4. 5. Remove the Loading Belt. Remove the screw 1. Remove the 2 screws 2. Remove the Loading Motor PCB Ass'y. Remove the Pulley Gear.
Loading Belt
Tray
Fig. 3-1-B 3-2: MAIN CHASSIS ASS'Y (Refer to Fig. 3-2-A) 1. 2. 3. 4. Remove the screw 1. Unlock the 2 supports 2. Remove the Insulator (R) from the Main Frame Ass'y. Remove the Main Chassis Ass'y.
1 2 2
Main Frame Ass'y
Screw Torque: 2.5 0.3kgfcm (Screw 1) Screw Torque: 1.0 0.3kgfcm (Screw 2) Insulator (R) Main Chassis Ass'y
Fig. 3-3-A
DISASSEMBLY INSTRUCTIONS
NOTE 1. In case of the Pulley Motor installation, check if the value of the Fig. 3-3-B is correct. 2. When installing the Loading Motor PCB Ass'y, install it correctly as Fig. 3-3-C. 3. In case of the Loading Motor PCB Ass'y installation, hook the wire on the Main Frame Ass'y as shown Fig. 3-3-C. 3-5: CLAMPER ASS'Y (Refer to Fig. 3-5-A) 1. Press the Clamper and rotate the Clamper Plate clockwise, then unlock the 3 supports 1. 2. Remove the Clamper Plate, Clamper Magnet and Clamper.
Clamper Plate Clamper Magnet
Pulley Motor
7.0 0.1mm
Main Frame
Loading Motor
1
Safety surface for pressing of the insert.
1 1
Clamper
Fig. 3-5-A
Fig. 3-3-B NOTE 1. In case of the Clamper Ass'y installation, install correctly as Fig. 3-5-B.
Clamper Plate
Clamper
No gap
Fig. 3-5-B
Check Hook Loading Motor PCB Assy
Fig. 3-3-C 3-6: TRAVERSE HOLDER/INSULATOR (F)/INSULATOR (R) (Refer to Fig. 3-6-A) 1. Remove the Traverse Holder. 2. Remove the 2 Insulator (F). 3. Remove the Insulator (R).
Insulator (R) Main Chassis Ass'y
3-4: RACK LOADING/MAIN GEAR/PULLEY GEAR (Refer to Fig. 3-4-A) 1. Press down the catcher 1 and slide the Rack Loading. 2. Unlock the support 2 and remove the Pulley Gear. 3. Remove the Main Gear.
Rack Loading
Fig. 3-4-A NOTE 1. In case of the Rack Loading installation, do not mesh it to the Main Gear as shown the Fig. 3-4-B.
Rack Loading Check Hook
Fig. 3-6-A NOTE 1. In case of the Insulator (F) installation, install correctly as Fig. 3-6-B. 2. In case of the Insulator (R) installation, install correctly as Fig. 3-6-C.
Insulator (F)
Traverse Holder
Main Gear
Fig. 3-6-B
DISASSEMBLY INSTRUCTIONS
Insulator (R) Main Chassis Ass'y (Top Side) Check Hook Check Hook Check Hook Main Chassis Ass'y (Bottom Side)
Fig. 3-6-C 3-7: SWITCH PCB ASS'Y/MIDDLE GEAR/FEED MOTOR (Refer to Fig. 3-7-A) 1. 2. 3. 4. 5. 6. 7. Remove the screw 1. Remove the Switch PCB Ass'y. Unlock the support 2. Remove the Middle Gear. Remove the 2 screws 3. Remove the Feed Motor. Remove the Motor Gear.
1
Switch PCB Ass'y Middle Gear
Fig. 3-7-D
3-8: FFC WIRE HANDLING 1. When installing the FFC, fold it correctly and install it as shown from Fig. 3-8-A to Fig. 3-8-C. NOTE 1. Do not make the folding lines except the specified positions for the FFC.
3 3
[ 24 pin FFC ]
Fold back at the border line of the reinforcement plate. 73 1mm Fold 10mm
Printing Surface
2
Motor Gear Main Chassis Ass'y Feed Motor Screw Torque: 3.0 0.3kgfcm (Screw 1) Screw Torque: 1.5 0.3kgfcm (Screw 3)
Fold it by 90 117 1mm 50 1mm
Fig. 3-7-A
NOTE 1. In case of the Motor Gear installation, check if the value of the Fig. 3-7-B is correct. 2. When installing the wire of the Switch PCB Ass'y, install it correctly as Fig. 3-7-C. 3. After the assembly of the Main Chassis Ass'y, hook the wire on the Main Chassis Ass'y as shown Fig. 3-7-D.
(3)
Reinforcement Plate
(4) (2)
Motor Gear 6.0 0.2mm
Fold
Printing Surface
Fig. 3-8-B
(3)
Reinforcement Plate
53 1mm
~ SPINDLE MOTOR ~ YELLOW (2)
GREEN (1)
(4) (2)
Fold Printing Surface 10 1mm Printing Surface Fold
Fig. 3-8-C
DISASSEMBLY INSTRUCTIONS
4. REMOVAL OF ANODE CAP
Read the following NOTED items before starting work. 3. After one side is removed, pull in the opposite direction to remove the other. NOTE Take care not to damage the Rubber Cap. INSTALLATION 1. Clean the spot where the cap was located with a small amount of alcohol. (Refer to Fig. 4-3.)
* *
After turning the power off there might still be a potential voltage that is very dangerous. When removing the Anode Cap, make sure to discharge the Anode Cap's potential voltage. Do not use pliers to loosen or tighten the Anode Cap terminal, this may cause the spring to be damaged.
REMOVAL 1. Follow the steps as follows to discharge the Anode Cap. (Refer to Fig. 4-1.) Connect one end of an Alligator Clip to the metal part of a flat-blade screwdriver and the other end to ground. While holding the plastic part of the insulated screwdriver, touch the support of the Anode with the tip of the screwdriver. A cracking noise will be heard as the voltage is discharged. Location of Anode Cap
Fig. 4-3 GND on the CRT NOTE Confirm that there is no dirt, dust, etc. at the spot where the cap was located. 2. Arrange the wire of the Anode Cap and make sure the wire is not twisted. 3. Turn over the Rubber Cap. (Refer to Fig. 4-4.)
Screwdriver
CRT
GND on the CRT Fig. 4-1 2. Flip up the sides of the Rubber Cap in the direction of the arrow and remove one side of the support. (Refer to Fig. 4-2.) Rubber Cap Fig. 4-4 4. Insert one end of the Anode Support into the anode button, then the other as shown in Fig. 4-5.
5. Confirm that the Support is securely connected. 6. Put on the Rubber Cap without moving any parts.
B4-1
DISASSEMBLY INSTRUCTIONS
5. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC
REMOVAL 1. Put Masking Tape (cotton tape) around the Flat Package IC to protect other parts from any damage. (Refer to Fig. 5-1.) NOTE Masking is carried out on all the parts located within 10 mm distance from IC leads.
Blower type IC desoldering machine
3. When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using a tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 5-3.) NOTE Some ICs on the PCB are affixed with glue, so be careful not to break or damage the foil of each IC leads or solder lands under the IC when removing it.
IC
Tweezers
Fig. 5-1
IC
2. Heat the IC leads using a blower type IC desoldering machine. (Refer to Fig. 5-2.) NOTE Do not rotate or move the IC back and forth until IC can move back and forth easily after desoldering the leads completely. 4. Peel off the Masking Tape.
Fig. 5-3
5. Absorb the solder left on the pattern using the Braided Shield Wire. (Refer to Fig. 5-4.) NOTE Do not move the Braided Shield Wire in the vertical direction towards the IC pattern.
Soldering Iron
IC
Fig. 5-2
IC pattern
Fig. 5-4
B5-1
DISASSEMBLY INSTRUCTIONS
INSTALLATION 1. Take care of the polarity of new IC and then install the new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily. (Refer to Fig. 5-5.) 4. When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thintip Soldering Iron. (Refer to Fig. 5-8.)
IC
Soldering Iron
Fig. 5-8 5. Finally, confirm the soldering status on four sides of the IC using a magnifying glass. Confirm that no abnormality is found on the soldering position and installation position of the parts around the IC. If some abnormality is found, correct by resoldering. NOTE When the IC leads are bent during soldering and/or repairing, do not repair the bending of leads. If the bending of leads are repaired, the pattern may be damaged. So, be always sure to replace the IC in this case.
Solder temporarily
Solder temporarily
Fig. 5-5 2. Supply the solder from the upper position of IC leads sliding to the lower position of the IC leads. (Refer to Fig. 5-6.)
Solder
Soldering Iron
IC
Fig. 5-6 3. Absorb the solder left on the lead using the Braided Shield Wire. (Refer to Fig. 5-7.) NOTE Do not absorb the solder to excess.
Soldering Iron IC
Fig. 5-7
B5-2
KEY TO ABBREVIATIONS
A A/C ACC AE AFC AFT AFT DET AGC AMP ANT A.PB APC ASSY AT AUTO A/V B BGP BOT BPF BRAKE SOL BUFF B/W C C CASE CAP CARR CH CLK CLOCK (SY-SE) COMB CONV CPM CTL CYL CYL-M CYL SENS D DATA (SY-CE) dB DC DD Unit DEMOD DET DEV E E EF EMPH ENC ENV EOT EQ EXT F F FBC FE FF FG FL SW FM FSC FWD G GEN GND H H.P.F : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : Audio/Control Automatic Color Control Audio Erase Automatic Frequency Control Automatic Fine Tuning Automatic Fine Tuning Detect Automatic Gain Control Amplifier Antenna Audio Playback Automatic Phase Control Assembly All Time Automatic Audio/Video Burst Gate Pulse Beginning of Tape Bandpass Filter Brake Solenoid Buffer Black and White Capacitance, Collector Cassette Capstan Carrier Channel Clock Clock (Syscon to Servo) Combination, Comb Filter Converter Capstan Motor Control Cylinder Cylinder-Motor Cylinder-Sensor Data (Syscon to Servo) Decibel Direct Current Direct Drive Motor Unit Demodulator Detector Deviation Emitter Emitter Follower Emphasis Encoder Envelope End of Tape Equalizer External Fuse Feed Back Clamp Full Erase Fast Forward, Flipflop Frequency Generator Front Loading Switch Frequency Modulation Frequency Sub Carrier Forward Generator Ground High Pass Filter I H.SW Hz IC IF IND INV KIL L LED LIMIT AMP LM, LDM LP L.P.F LUMI. M MAX MINI MIX MM MOD MPX MS SW NC NR OSC OPE PB PB CTL PB-C PB-Y PCB P. CON PD PG P-P R REC REC-C REC-Y REEL BRK REEL S REF REG REW REV, RVS RF RMC RY S. CLK S. COM S. DATA SEG SEL SENS SER SI SIF SO SOL SP STB SW : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : Head Switch Hertz Integrated Circuit Intermediate Frequency Indicator Inverter Killer Left Light Emitting Diode Limiter Amplifier Loading Motor Long Play Low Pass Filter Luminance Motor Maximum Minimum Mixer, mixing Monostable Multivibrator Modulator, Modulation Multiplexer, Multiplex Mecha State Switch Non Connection Noise Reduction Oscillator Operation Playback Playback Control Playback-Chrominance Playback-Luminance Printed Circuit Board Power Control Phase Detector Pulse Generator Peak-to Peak Right Recording Recording-Chrominance Recording-Luminance Reel Brake Reel Sensor Reference Regulated, Regulator Rewind Reverse Radio Frequency Remote Control Relay Serial Clock Sensor Common Serial Data Segment Select, Selector Sensor Search Mode Serial Input Sound Intermediate Frequency Serial Output Solenoid Standard Play Serial Strobe Switch
K L
N O P
C1-1
KEY TO ABBREVIATIONS
S SYNC SYNC SEP T TR TRAC TRICK PB TP U UNREG V V VCO VIF VP V.PB VR V.REC VSF VSR VSS V-SYNC VT X XTAL Y Y/C : : : : : : : : : : : : : : : : : : : : : Synchronization Sync Separator, Separation Transistor Tracking Trick Playback Test Point Unregulated Volt Voltage Controlled Oscillator Video Intermediate Frequency Vertical Pulse, Voltage Display Video Playback Variable Resistor Video Recording Visual Search Fast Forward Visual Search Rewind Voltage Super Source Vertical-Synchronization Voltage Tuning Crystal Luminance/Chrominance
C1-2
3 4
2 2
REC/OTR
STOP (DVD)
Set Key
Set Key
Operations The BOT, EOT, and the Reel Sensor do not work and the VCR deck can be operated without a cassette tape. Refer to the "PREPARATION FOR SERVICING" Operations
FF
Method Press the ATR button on the remote control for more than 2 seconds during PLAY.
Adjust Tracking to the center position. Refer to the "MECHANICAL ADJUSTMENT" (GUIDE ROLLER) and "ELECTRICAL ADJUSTMENT" (PG SHIFTER).
C2-1
Initial setting content of MEMORY IC. POWER ON total hours. PLAY/REC total hours.
(16 x 16 x 16 x thousands digit value) + (16 x 16 x hundreds digit value) + (16 x tens digit value) + (ones digit value)
C3-1
C3-2
+8 86 00 1A 00 ---
+9 00 F4 0B 23 ---
+A D0 15 3D FF ---
+B 18 4B 18 FF ---
+C A6 1D 37 FF ---
+D 01 54 16 80 ---
+E 86 83 27 88 ---
+F 55 B1 30 83 ---
INIT
00
2F
Fig. 1 3. ADDRESS is now selected and should "blink". Using the UP or DOWN button on the remote, step through the ADDRESS until required ADDRESS to be changed is reached. 4. Press ENTER to select DATA. When DATA is selected, it will "blink". 5. Again, step through the DATA using UP or DOWN button until required DATA value has been selected. 6. Pressing ENTER will take you back to ADDRESS for further selection if necessary. 7. Repeat steps 3 to 6 until all data has been checked. 8. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input. After the data input, set to the initializing of shipping. 9. Turn POWER on. 10. Press both VOL. DOWN button on the set and the Channel button (1) on the remote control for more than 2 seconds. 11. After the finishing of the initializing of shipping, the unit will turn off automatically. The unit will now have the correct DATA for the new MEMORY IC.
C4-1
JG185 Tentelometer
Ref. No. JG001 JG001A JG001Q JG001T JG001B JG001I JG001P JG001S JG002B JG002E JG002F JG005 JG153 JG022 JG024A JG100A JG185
Part No. APJG001000 APJG001A00 APJG001Q00 APJG001T00 APJG001B00 APJG001I00 APJG001P00 APJG001S00 APJG002B00 APJG002E00 APJG002F00 APJG005000 APJG153000 APJG022000 APJG024A00 APJG100A00 APJG185000
Parts Name VHS Alignment Tape VHS Alignment Tape VHS Alignment Tape VHS Alignment Tape VHS Alignment Tape VHS Alignment Tape VHS Alignment Tape VHS Alignment Tape Adapter Dial Torque Gauge (10~90gfcm) Dial Torque Gauge (60~600gfcm) Post Adjustment Screwdriver X Value Adjustment Screwdriver Master Plane Reel Disk Height Adjustment Jig Torque Tape (VHT-063) Tentelometer
Remarks Monoscope, 6KHz (For 2 heads model) Color Bar, 1KHz (For 2 heads model) Hi-Fi Audio (For 2 heads model) X Value Adjustment (For 2 heads model) Monoscope, 6KHz (For 4 heads model) Color Bar, 1KHz (For 4 heads model) Hi-Fi Audio (For 4 heads model) X Value Adjustment (For 4 heads model) VSR Torque, Brake Torque (S Reel/T Reel Ass'y) Brake Torque (T Reel Ass'y) VSR Torque, Brake Torque (S Reel) Guide Roller Adjustment X Value Adjustment Reel Disk Height Adjustment Reel Disk Height Adjustment Playback Torque, Back Tension Torque During Playback Confirmation of Tape Tension on Playback
D1-1
MECHANICAL ADJUSTMENTS
1. CONFIRMATION AND ADJUSTMENT
Read the following NOTES before starting work. Place an object which weighs between 450g~500g on the Cassette Tape to keep it steady when you want to make the tape run without the Cassette Holder. (Do not place an object which weighs over 500g.) 1-2: CONFIRMATION AND ADJUSTMENT OF TENSION POST POSITION 1. Set to the PLAY mode. 2. Adjust the adjusting section for the Tension Arm position so that the Tension Arm top is within the standard line of Main Chassis. 3. While turning the S Reel clockwise, confirm that the edge of the Tension Arm is located in the position described above.
Standard line of Main Chassis
1-1: CONFIRMATION AND ADJUSTMENT OF REEL DISK HEIGHT 1. Turn on the power and set to the STOP mode. 2. Set the master plane (JG022) and reel disk height adjustment jig (JG024A) on the mechanism framework, taking care not to scratch the drum, as shown in Fig. 11-A. 3. While turning the reel and confirm the following points. Check if the surface A of reel disk is lower than the surface B of reel disk height adjustment jig (JG024A) and is higher than the surface C. If it is not passed, place the height adjustment washers and adjust to 10(+2, -0)mm. 4. Adjust the other reel in the same way.
Master Plane (JG022)
Tension Arm
Fig. 1-2-A
Tension Band
The Tension Arm top will move to the inside direction of the Main Chassis. Bend
The Tension Arm top will move to the outside direction of the Main Chassis.
Fig. 1-2-B
Fig. 1-1-A
Reel Disk Height Adjustment Jig (JG024A) (B)
1-3: CONFIRMATION OF PLAYBACK TORQUE AND BACK TENSION TORQUE DURING PLAYBACK 1. Load a video tape (T-120) recorded in standard speed mode. Set the unit to the PLAY mode. 2. Install the tentelometer (JG185) as shown in Fig. 1-3. Confirm that the meter indicates 20 2gf in the beginning of playback. USING A CASSETTE TYPE TORQUE TAPE (JG100A) 1. After confirmation and adjustment of Tension Post position (Refer to item 1-2), load the cassette type torque tape (JG100A) and set to the PLAY mode. 2. Confirm that the right meter of the torque tape indicates 50~90gfcm during playback in SP mode. 3. Confirm that the left meter of the torque tape indicates 25~40gfcm during playback in SP mode.
Tentelometer (JG185)
Reel Disk
10(+0.2, -0)mm
(C)
Fig. 1-1-B
Video Tape
P1 Post
Guide Roller
Fig. 1-3
D2-1
MECHANICAL ADJUSTMENTS
1-4: CONFIRMATION OF VSR TORQUE 1. Install the Torque Gauge (JG002F) and Adapter (JG002B) on the S Reel. Set to the Picture Search (Rewind) mode. (Refer to Fig.1-4-B) 2. Then, confirm that it indicates 120~180gfcm. NOTE Install the Torque Gauge on the reel disk firmly. Press the REW button to turn the reel disk. 1-5: CONFIRMATION OF REEL BRAKE TORQUE (S Reel Brake) (Refer to Fig. 1-4-B) 1. Once set to the Fast Forward mode then set to the Stop mode. While, unplug the AC cord when the Pinch Roller Block is on the position of Fig. 1-4-A. 2. Move the Idler Assy from the S Reel. 3. Install the Torque Gauge (JG002F) and Adapter (JG002B) on the S Reel. Turn the Torque Gauge (JG002F) clockwise. 4. Then, confirm that it indicates 60~100gfcm. (T Reel Brake) (Refer to Fig. 1-4-B) 1. Once set to the Fast Forward mode then set to the Stop mode. While, unplug the AC cord when the Pinch Roller Block is on the position of Fig. 1-4-A. 2. Move the Idler Assy from the T Reel. 3. Install the Torque Gauge (JG002E) and Adapter (JG002B) on the T reel. Turn the Torque Gauge (JG002E) counterclockwise. 4. Then, confirm that it indicates 30~50gfcm.
The position at FF mode. Pinch Roller Block Stop at this position.
NOTE If the torque is out of the range, replace the following parts. Check item 1-4 1-5 Replacement Part Idler Assy/Clutch Assy S Reel side: S Reel/Tension Band/Tension Connect/Tension Arm Assy T Reel side: T Reel/T Brake Band//T Brake Spring/T Brake Arm
Fig. 1-4-A
Fig. 2-1-A
Entrance S Reel Max A B Max Exit
T Reel
Fig. 1-4-B
A : B >3 : 2
Fig. 2-1-B
D2-2
MECHANICAL ADJUSTMENTS
2-2: CONFIRMATION AND ADJUSTMENT OF AUDIO/ CONTROL HEAD When the Tape Running Mechanism does not work well, adjust the following items. 1. Playback the VHS Alignment Tape (JG001 or JG001B). (Refer to SERVICING FIXTURE AND TOOLS) 2. Confirm that the reflected picture of stamp mark is appeared on the tape prior to P4 Post as shown in Fig. 22-A. a) When the reflected picture is distorted, turn the screw (1) clockwise until the distortion is disappeared. b) When the reflected picture is not distorted, turn the screw (1) counterclockwise until little distortion is appeared, then adjust the a). 3. Turn the screw (2) to set the audio level to maximum. 4. Confirm that the bottom of the Audio/ Control Head and the bottom of the tape is shown in Fig. 2-2-C. c) When the height is not correct, turn the screw (3) to adjust the height. Then, adjust the 1~3 again.
Audio/Control Head Reflected picture of Stamp Mark P4 Cap (1) CH-3 Audio (2) Envelope
2-3: TAPE RUNNING ADJUSTMENT (X VALUE ADJUSTMENT) 1. Confirm and adjust the height of the Reel Disk. (Refer to item 1-1) 2. Confirm and adjust the position of the Tension Post. (Refer to item 1-2) 3. Adjust the Guide Roller. (Refer to item 2-1) 4. Confirm and adjust the Audio/Control Head. (Refer to item 2-2) 5. Connect CH-1 of the oscilloscope to TP102, CH-2 to TP4501 and CH-3 to HOT side of Audio Out Jack. 6. Playback the VHS Alignment Tape (JG001S or JG001T). (Refer to SERVICING FIXTURE AND TOOLS) 7. Press and hold the Tracking-Auto button on the remote control more than 2 seconds to set tracking to center. 8. Set the X Value adjustment driver (JG153) to the (4) of Fig. 2-2-B. Adjust X value so that the envelope waveform output becomes maximum. Check if the relation between Audio and Envelope waveform becomes (1) or (2) of Fig. 2-3.
Fig. 2-3
Stamp Mark
Fig. 2-2-A
2-4: CONFIRM Hi-Fi AUDIO (Hi-Fi model only) 1. Connect CH-1 of the oscilloscope to TP4501 and CH-2 to the Hi-Fi Audio Out Jack. 2. Playback the VHS Alignment Tape (JG001P or JG001Q). Refer to SERVICING FIXTURE AND TOOLS) 3. Press and hold the Tracking-Auto button on the remote control more than 2 seconds to set tracking to center. 4. Press the Tracking Up button and count number of steps which the audio output is changed from Hi-Fi (10KHz) to MONO (6KHz). 5. Press and hold the Tracking-Auto button on the remote control more than 2 seconds to set tracking to center. 6. Press the Tracking Down button and count number of steps which the audio output is changed from Hi-Fi (10KHz) to MONO (6KHz). 7. If the difference are more than 3 steps, set the X Value adjustment driver (JG153) to (4) of Fig. 2-2-B. Change the X Value and adjust it so that the value becomes within 2 steps.
Audio/Control Head
(3)
(1)
(2) (4)
Fig. 2-2-B
0.25 0.05mm
Fig. 2-2-C
D2-3
MECHANICAL ADJUSTMENTS
3. MECHANISM ADJUSTMENT PARTS LOCATION GUIDE
4 5
6 3
10
1. Tension Connect 2. Tension Arm 3. Guide Roller 4. Audio/Control Head 5. X value adjustment driver hole
6. P4 Post 7. T Brake Spring 8. T Reel 9. S Reel 10. Adjusting section for the Tension Arm position
D2-4
ELECTRICAL ADJUSTMENTS
1. BEFORE MAKING ELECTRICAL ADJUSTMENTS
Read and perform these adjustments when repairing the circuits or replacing electrical parts or PCB assemblies. CAUTION Use an isolation transformer when performing any service on this chassis. Before removing the anode cap, discharge electricity because it contains high voltage. When removing a PCB or related component, after unfastening or changing a wire, be sure to put the wire back in its original position. When you exchange IC and Transistor with a heat sink, apply silicon grease(YG6260M) on the contact section of the heat sink. Before applying new silicon grease, remove all the old silicon grease. (Old grease may cause damages to the IC and Transistor). Prepare the following measurement tools for electrical adjustments. 1. Oscilloscope 2. Digital Voltmeter 3. Multi-sound Generator 4. Pattern Generator On-Screen Display Adjustment 1. Unplug the AC plug for more than 5 seconds to set the clock to the non-setting state. Then, set the volume level to minimum. 2. Press the VOL. DOWN button on the set and the Channel button (9) on the remote control for more than 2 seconds to appear the adjustment mode on the screen as shown in Fig. 1-1.
NO. 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 FUNCTION OSD H OSD C CUT OFF H.POSI H.BLK L H.BLK R V.SIZE V.POSI V.LIN VS.CORR V.COMP R.BIAS G.BIAS B.BIAS R.DRV G.DRV B.DRV BRI CENT BRI MAX BRI MIN NO. 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 38 FUNCTION CONT CENT CONT MAX CONT MIN COL CENT COL MAX COL MIN TINT SHARP SUB BIAS H.SIZE PARABOLA TRAPEZIUM COR TOP COR BTM H.COMP T.STE H.FREQ
Fig. 1-2
TV
00 OSD
7 Fig. 1-1
5. Press the VOL. DOWN button on the set and the channel button (3) on the remote control for more than 2 seconds until the indicator REC disappears. 6. When the REC indicator is blinking, press both VOL. DOWN button on the set and the channel button (4) on the remote control for more than 2 seconds and adjust the Tracking +/- button until the arising to the down of Head Switching Pulse becomes 6.5 0.5H. (Refer to Fig. 2-1-A, B)
3. Use the Channel UP/DOWN button or Channel button (0-9) on the remote control to select the options shown in Fig. 1-2. 4. Press the MENU button on the remote control to end the adjustments.
CH-2
6.5H CH-1
Fig. 2-1-A
CH-2
CH-1 6.5H
Fig. 2-1-B
D3-1
ELECTRICAL ADJUSTMENTS
(TV SECTION)
2-2: CONSTANT VOLTAGE 1. Place the set in AV MODE without signal. 2. Using the remote control, set the brightness and contrast to normal position. 3. Connect the digital voltmeter to TP401. 4. Adjust the VR1701 until the digital voltmeter is 114 0.5V. 2-3: CUT OFF 1. Adjust the unit to the following settings. BRI.CENTER=127, CONT MAX=100,R.BIAS=127, G.BIAS=127, B.BIAS=127, R.DRV=63, G.DRV=07, B.DRV=63. 2. Place the set in Aging Test for more than 15 minutes. 3. Place the set in AV MODE without signal. 4. Using the remote control, set the brightness and contrast to normal position. 5. Activate the adjustment mode display of Fig. 1-1 and press the channel button (02) on the remote control to select "CUT OFF". 6. Adjust the Screen Volume until a dim raster is obtained. 2-4: WHITE BALANCE NOTE: Adjust after performing CUT OFF adjustment. 1. Place the set in Aging Test for more than 15 minutes. 2. Receive the gray scale pattern from the Pattern Generator with Burst On. 3. Using the remote control, set the brightness and contrast to normal position. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (11) on the remote control to select "R.BIAS". 5. Press the CH. UP/DOWN button on the remote control to select the "R.BIAS", "G.BIAS", "B.BIAS", "R.DRV", "B.DRV" or "G.DRV". 6. Adjust the LEFT/RIGHT button on the remote control to whiten the R.BIAS, G.BIAS, B.BIAS, R.DRV, B.DRV, and G.DRV at each step tone sections equally. 7. Perform the above adjustments 5 and 6 until the white color is achieved. 2-5: HORIZONTAL POSITION 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (03) on the remote control to select "H.POSI". 4. Press the LEFT/RIGHT button on the remote control until the SHIFT quantity of the OVER SCAN on right and left becomes minimum. 2-6: FOCUS 1. Receive the monoscope pattern. 2. Turn the Focus Volume fully counterclockwise once. 3. Adjust the Focus Volume until picture is distinct. 2-7: VERTICAL SIZE 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (06) on the remote control to select "V.SIZE". 4. Press the LEFT/RIGHT button on the remote control until the Up/Down OVER SCAN Quantity becomes equal to the Right/Left OVER SCAN Quantity. 2-8: VERTICAL LINEARITY NOTE: Adjust after performing adjustments in section 2-5. After the adjustment of Vertical Linearity, reconfirm the Vertical Position and Vertical Size adjustments. 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (08) on the remote control to select "V.LIN". 4. Press the LEFT/RIGHT button on the remote control until the SHIFT quantity of the OVER SCAN on right and left becomes minimum. 2-9: BRIGHT CENTER 1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (17) on the remote control to select "BRI CENT". 2. Press the LEFT/RIGHT button on the remote control until the white 10% is starting to be visible. 3. Press the INPUT SELECT button on the remote control to set to the AV mode. Then perform the above adjustments 1, 2. 4. Press the DVD button on the remote control to set to the DVD mode. 5. Activate the adjustment mode display of Fig. 1-1 and press the channel button (17) on the remote control to select "BRI CENT". 6. Press the LEFT/RIGHT button on the remote control to set the same step numbers as the AV mode.
D3-2
ELECTRICAL ADJUSTMENTS
2-10: OSD HORIZONTAL 1. Activate the adjustment mode display of Fig. 1-1. 2. Press the LEFT/RIGHT button on the remote control until the difference of A and B becomes minimum. (Refer to Fig. 2-2) 2-12: VERTICAL POSITION 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (07) on the remote control to select "V.POSI". 4. Check if the step No. V POSI is "02". 5. Adjust the VR404 until the horizontal line becomes fit to notch of the shadow mask. (Refer to Fig. 2-4)
TV
horizontal line 00 OSD A 2-11: TINT 1. Receive the color bar pattern. (RF Input) 2. Using the remote control, set the brightness, contrast, color and tint to normal position. 3. Connect the oscilloscope to TP803. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (26) on the remote control to select "TINT". 5. Press the LEFT/RIGHT button on the remote control until the section "A" becomes a straight line (Refer to Fig. 2-3). 6. Receive the color bar pattern. (Audio Video Input) 7. Press the INPUT SELECT button on the remote control to set to the AV mode. Then perform the above adjustments 2~5. 8. Press the DVD button on the remote control to set to the DVD mode. 9. Activate the adjustment mode display of Fig. 1-1 and press the channel button (26) on the remote control to select "TINT". 10. Press the LEFT/RIGHT button on the remote control until the tint step No. becomes "67". 9 B
Fig. 2-2
,, ,, ,, ,, , ,, ,, ,,
Notch
Shadow mask Fig. 2-4 2-13: COLOR CENTER 1. Receive the color bar pattern. (RF Input) 2. Using the remote control, set the brightness, contrast, color and tint to normal position. 3. Connect the oscilloscope to TP802. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (23) on the remote control to select "COL CENT". 5. Adjust the VOLTS RANGE VARIABLE knob of the oscilloscope until the range between white 100% and 0% is set to 4 scales on the screen of the oscilloscope. 6. Press the LEFT/RIGHT button on the remote control until the red color level is adjusted to 90 5% of the white level. (Refer to Fig. 2-5) 7. Receive the color bar pattern. (Audio Video Input) 8. Press the INPUT SELECT button on the remote control to set to the AV mode. Then perform the above adjustments 2~6. 9. Press the DVD button on the remote control to set to the DVD mode. 10. Activate the adjustment mode display of Fig. 1-1 and press the channel button (23) on the remote control to select "COL CENT". 11. Press the LEFT/RIGHT button on the remote control to set the same step numbers as the AV mode.
"A"
Fig. 2-3
90% 100%
Fig. 2-5
D3-3
ELECTRICAL ADJUSTMENTS
2-14: CONTRAST MAX 1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (21) on the remote control to select "CONT MAX". 2. Press the LEFT/RIGHT button on the remote control until the contrast step No. becomes "60". 3. Receive a broadcast and check if the picture is normal. 4. Press the INPUT SELECT button on the remote control to set to the AV mode. Then perform the above adjustments 1~3. 5. Press the DVD button on the remote control to set to the DVD mode. 6. Activate the adjustment mode display of Fig. 1-1 and press the channel button (21) on the remote control to select "CONT MAX". 7. Press the LEFT/RIGHT button on the remote control to set the same step numbers as the AV mode. 2-15: Confirmation of Fixed Value (step No.) Please check if the fixed values of the each adjustment items are set correctly referring below. NO. 01 04 05 09 10 15 18 19 20 22 24 25 27 28 29 30 31 32 33 34 35 FUNCTION OSD CONT H.BLK L H.BLK R VS.CORR V.COMP G.DRV BRI MAX BRI MIN CONT CENT CONT MIN COL MAX COL MIN SHARPNESS SUB BIAS H.SIZE PARABOLA TRAPEZIUM COR TOP COR BOT H.COMP T.STE RF 02 02 02 07 03 07 100 25 25 10 127 00 30 20 00 00 00 00 00 00 00 AV 02 02 02 07 03 07 100 25 25 10 127 00 30 20 00 00 00 00 00 00 00 DVD 02 02 02 07 03 07 100 25 25 10 127 00 15 20 00 00 00 00 00 00 00
D3-4
ELECTRICAL ADJUSTMENTS
3. PURITY AND CONVERGENCE ADJUSTMENTS
NOTE 1. Turn the unit on and let it warm up for at least 30 minutes before performing the following adjustments. 2. Place the CRT surface facing east or west to reduce the terrestrial magnetism. 3. Turn ON the unit and demagnetize with a Degauss Coil. 3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT) 1. Tighten the screw for the magnet. Refer to the adjusted CRT for the position. (Refer to Fig. 3-1) If the deflection yoke and magnet are in one body, untighten the screw for the body. 2. Receive the green raster pattern from the color bar generator. 3. Slide the deflection yoke until it touches the funnel side of the CRT. 4. Adjust center of screen to green, with red and blue on the sides, using the pair of purity magnets. 5. Switch the color bar generator from the green raster pattern to the crosshatch pattern. 6. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 7. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 8. Adjust the crosshatch pattern to change to white by repeating steps 6 and 7. 3-2: PURITY NOTE Adjust after performing adjustments in section 3-1. 1. Receive the green raster pattern from color bar generator. 2. Adjust the pair of purity magnets to center the color on the screen. Adjust the pair of purity magnets so the color at the ends are equally wide. 3. Move the deflection yoke backward (to neck side) slowly, and stop it at the position when the whole screen is green. 4. Confirm red and blue color. 5. Adjust the slant of the deflection yoke while watching the screen, then tighten the fixing screw. DEFLECTION YOKE DEFLECTION YOKE SCREW MAGNET SCREW 3-3: STATIC CONVERGENCE NOTE Adjust after performing adjustments in section 3-2. 1. Receive the crosshatch pattern from the color bar generator. 2. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 3. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 3-4: DYNAMIC CONVERGENCE NOTE Adjust after performing adjustments in section 3-3. 1. Adjust the differences around the screen by moving the deflection yoke upward/downward and right/left. (Refer to Fig. 3-2-a) 2. Insert three wedges between the deflection yoke and CRT funnel to fix the deflection yoke. (Refer to Fig. 3-2-b) RGB RGB
R G B
R G B
WEDGE
WEDGE
D3-5
ELECTRICAL ADJUSTMENTS
4. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION)
AC IN CD002
J4202
J8007
DEFLECTION PCB
CP601
J4201
CRT
CD1704 CP1704 CD1703
TU001
CP8001
DVD DECK
TP4201
CP802A
FB401
VR404
CP303
VR1701
02 CD6
CP4502
CP001
CD802
CP1702
CD303
SPEAKER
CP4503
CRT PCB
TP803 TP802
CP802B CP603B
CD8101
FE HEAD
AC HEAD
TP4501 TP102
J2201
J2202
CP2201
CD2251
VCR PCB
OPERATION PCB
DVD DECK
CP2303 CP8101 CP2302
CD4002
CP2301
DVD PCB
CD2001 CD2301 CD2302
D3-6
I 2 CDAT
I 2 CCLK
A A, C B +3.3V, 1.9V REG IC4003 BA33E00WHFP-TR C C D E
RF, A, B, C, D, E, F
MD_CD, MD_DVD OPU OPE-AMP IC2304 BA10358FV-E2 D VR_DVD, VR_CD
TX RX
SPDIF
DVD/CD, DVD_LD, CD_LD TR+/-, FO+/-, MOT_LD+/-, MOT_SLED+/-, MOT_SPDL+/SPINDLE/SLED/ FOCUS/TRACK_PWM, TRAY_CLOSE/OPEN
ADCIN_5, 6, 7 E
CP8101
Y C CVBS
DVD RESET ZERO
AUDIO L AUDIO R
SD_A0~A10
SD_D0~D15
SD_A0~A10
SD_D0~D15
A---3.3V B---1.8V
E-1
E-2
X4501 3.579545MHz
Q4507
Y/C/AUDIO/HEAD AMP IC IC4501 LA71205M-MPB 50 VX01 TIMMING 67 L H.SW H 66 49 BUFFER
Q4509
BUFFER 39 OUT CCD FM MOD WC DC CLAMP NL EMPHA V/I CONV Y-LPF R R YNR/ COMB N.L. DEEM NC1 Y/C MIX 1/2 H.AMP SW/ AUDIO 58 MUTE VCA CLAMP 36 34 DETAL ENH P P 21 DECODER 37 55 54 53 Y/C_CS Y/C_DATA Y/C_CLK MICON
SERIAL
AGC AMP
KIL C-LPF
CLAMP
22
Main CONV
KIL B.D.
PB AMP
FM DEM
9 7
REC AMP
P FBC R
C ROT 57 RF SW IN
FE HEAD
MUTE
Y/C_VIDEO
SYNC SEP 80 78 76 32 30 28 6dB 26
Q4511
BUFFER
V SYNC
CHROMA/IF
Hi-Fi/ DEMODULATOR
1 AE HEAD(-)
Q4503
SW V.REC_ST_H CTL+ CTLMICON
E-3
E-4
Hi-Fi/DEMODULATOR
15 RX
AV_SW1 RX DVD IN/OUT TX DVD RESET T-REC_LED REC_LED EXT_A_MUTE IN/OUT EXT_MUTE KEY-B KEY-A REMOCON_IN AT 5V CENT LED D101 CENT LED SW BOT SENSOR Q101 EOT SENSOR Q103 REEL SENS Q108 4
CP101 11 CYL FG/PG
OSC0 OSCI CVN2 DUMMY.V.SYNC H.SW C_ROTARY Y/C CS VCR.A.MUTE H.AMP SW1 V.REC START-H ENV.DET CTL(+) CTL(-)
16 TX X101 32.768KHz 41 X0 40 XI 95 DVD RESET 90 T-REC LED 91 REC/OTR LED 9 EXT_A_MUTE 6 EXT_MUTE 81 KEY-B 80 KEY-A 5 REMOCON IN
REGULATOR
VIDEO OUT Y/C VIDEO DUMMY_V.SYNC H.SW C.ROTARY Y/C_CS VCR_A_MUTE H.AMP_SW1 V.REC_ST-H ENV.DET CTL+ CTLY/C_DATA Y/C_CLK COMP TV_POWER_H Y/C/AUDIO/ HEAD AMP
Y/C DATA
Y/C CLK
COMP 100
EMERGENCY 86 DEGAUSS 60
TV
4 3
REEL-S REEL-T
AFT
85
AFT PROTECT SCL SDA SW101 EEP ROM IC IC199 BR24L04F-WE2 6 SCL 5 SDA CHROMA/IF
CAPSTAN DD UNIT
12 CYL DRIVE 10 LDM CTL 5 I LIMIT 9 CAP CTL 1 CAP FG 4 CAP.M F/R 2 CAP VCO 8 LD/CY_VCO
58 CYL SPEED UP 65 CYL_FG/PG 34 DRUM PWM 78 LDM CTL 32 CAP FULL 33 CAP PWM 21 CAP LIMIT 67 FGF 64 CAP_F/R
TAB SW
97
TAB SW
IC103 XC61CN3102SR
RESET 25 1 SYSTEM RESET IC
27 DVD_H
OSD_R OSD_G OSD_B OSD_Y H.SYNC V.SYNC TV_POWER_H TV_A_MUTE SCL SDA
SOUND AMP/ SURROUND
83 MS SEN-A 82 MS SEN-B
CHROMA/IF
E-5
E-6
OPEN/CLOSE
VOL DOWN VOL UP SKIP STOP PLAY SKIP POWER
MUTE SW
Q4203 MUTE SW Q4211 CH MUTE SW_AUDIO_OUT_L SOUND AMP/ SURROUND SOUND_R+ SOUND_L+ SP_OUT_R SP_OUT_L SW_AUDIO_OUT_R
3
4 2
6
5 7 Q4210 LED D2205 Q2201 REC LED SW MUTE SW Q4212 BUFFER REC/OTR LED
MICON
D2206 T-REC
LED
D2207
POWER OS2201
6
REMOCON_IN 1
3
4 3
REAR_A_IN_L REAR_A_IN_R
2
TV_POWER_H T-REC_LED REC_LED FRONT VIDEO JACK J2202 2
Q4204
Hi-Fi/DEMODULATOR
ZERO SW
Q8002
D AUDIO DRIVER
FRONT_A_IN_L
FRONT_A_IN_R
E-7
E-8
PROTECT
MICON
60 57 56 55 54
36 X601 3.579545MHz 35 5
MICON
V_SYNC SDA
6
51 50 59
11 13 21
SCL
H.SYNC
SW_C
DIGITAL COMB FILTER
40 32
7
25 16 14 15
DVD IN/OUT
30
19 10 23
TV_POWER_H
MICON
EMERGENCY
EMERGENCY SW +B DOWN
E-9
E-10
12 4 10
TV
SOUND +B
SOUND_R+ SOUND_L+
IN/OUT
SP_OUT_L SP_OUT_R
18 17
SURROUND-IC IC302 AN5891SA-E1V
16 19
SW_AUDIO_OUT_R
31
30 3
IN/OUT
SW_AUDIO_OUT_L
REGULATOR
P.CON+8V
E-11
E-12
AGC
L/R MIX
REC LPF
VCO 1
HF1
22
2 AMP 4 3
INPUT SW
HF2 24 AMP
10 15 9
REAR_A_IN_R REAR_A_IN_L
HF_COM
21 AMP
14 53 57 59 NC
OUTPUT SW
Y/C/AUDIO/ HEAD AMP
AMP RFC
PNR VCO-FO ADJ LOGIC FSC Y/C_AUDIO NORMAL_A 45 62 61 DBX NOISE REDUCTION DEM BLOCK FM LIM 30
BPF 48
TUNER_AUDIO
29
V. REC_ST-H
HIFI_ENV
HIFI_H.SW
MICON
REGULATOR
E-13
E-14
P.CON+5V REGULATOR P.CON+12V P.CON+8V AT+30V DIGITAL COMB FILTER IC IC1501 TC90A45FG 4 13 15 10 16 8
Q1502 BUFFER
Q1501 BUFFER
AV SW IC IC1502 MM1501XNRE
1 3 4 Q1503 BUFFER
AV SW IC IC1504 MM1501XNRE
Y/C_VIDEO
AUX_V[F/R]
1 3 4 TU001 115-V-KA35ARB
VIDEO OUT SW IC IC1505 MM1504XNRE REAR_V_IN FRONT_V_IN IN/OUT
JACK_OUT
1 3 4
TUNER_AUDIO
Hi-Fi/ DEMODULATOR
E-15
E-16
AV SW1 DVD_RESET
CP8001
MICON
3 4 6 7 8 9 11
DVD+3.8V DVD+3.8V
SPDIF-134 AUDIO SW IC IC8001 MM1501XNRE
Q8006, Q8007 ZERO MUTE SW
DVD+3.8V
P.CON+12V ZERO SPDIF-134 IN/OUT
1 4
6 2 3
CP8002
2 3 4 6 8 10 12
CVBS
DVD_VIDEO
SW_AUDIO_OUT_L SW_AUDIO_OUT_R
E-17
E-18
AT+12V
VCR_POWER_H
P.CON+5V_A
P.CON+5V_A OUT IC IC3003 KIA278R05PI
P.CON+5V OUT IC IC3004 KIA278R05PI P.CON+5V_D OUT IC IC3001 KIA278R05PI P.CON+9V_D OUT IC IC3002 KIA278R09PI
P.CON+5V_C
P.CON+5V AT+5V IN/OUT
1 UNREG+8V TV MOTOR+12V
4
Q3001
P.CON+8V BUFFER
Q3008, Q3009
P.CON+5V_A P.CON+12V
Hi-Fi/DEMODULATOR
UNREG+5V +B
Q3015
SW
BUFFER P.CON+5V_A
Q3002 P.CON+8V SW
P.CON+8V P.CON+5V
P.CON+12V
Q3011 SW
P.CON+8V +30V
DVD IN/OUT
AT+5V
Q3010 P.CON+5V_C SW
CHROMA/IF
P.CON+8V
P.CON+8V
SOUND AMP/SURROUND
E-19
E-20
TV BLOCK DIAGRAM
MOTOR+12V Q1702 RELAY DRIVE 2 1 DEGAUSS RELAY RY1701 3 L1703 DEGAUSS COIL D1705, D1706, D1710, D1711 Q406 AC IN F1701 TRANSFORMER SWITCHING T1701 18 CURRENT DET 4 +B REGULATOR UNREG+8V UNREG+5V DEGAUSS_H MICON
17 1 Q1705, Q1706 SWITCHING 6 7 10 11 SOUND +B SOUND AMP CP603 Q802, Q803 V.OUTPUT IC IC401 LA78040 7 1 5 2 Q408 SW RED AMP Q804, Q805 GREEN AMP Q806, Q807 BLUE AMP CUT OFF R.OUT G.OUT B.OUT CLAMP OFF 1 3 4 5 6 14
DY J801 11 CP602B 1 6 7 2 3 4 8 9 V.OUT H.OUT P.CON+5V TV_POWER_H AFC ACL EMERGENCY +B DOWN Q407 H_VOLT_SW Q409 H_VOLT_SW 3 2 9 7 HV Q401 H.DRIVE T401 5 2 Q403 FL OUT FB401 1 3 FBT F S 6 8 F 7 V801 CRT
E-21
E-22
F-1
Q2302 B4002 C4076 C4071_1 Q2301 R2332 C2327_1 C2346_1 C2343_1 C4064 C4068_1 R8116 C4039 R4041 C4070_1 C2340_1 R2340 C2341_1 C2316 C4042 C4053_1 C4089 R4044 W854 R4040 C4100 IC4003 R4081 R4009 R4080 C4011_1 B4007 R4070 C4043 C4009_1 C2348 C2309 C2328_1 R2360 CP2301 B4005 C4062 R2333 IC4007 C4091 D4001 R4011 R4013 C4084_1 C4090 C4063 C4095 C4067_1 C4021 C4083_1 C4016 C4017 R4049 C4008 1 53 R4054 R4053 C4077 C4044 C4078_1 B4006 Q4004 L4001 CD4002 R4063 C4087 R4048_1 C4047_1 R4052 C4096 W847 W849 C4074 IC4008 IC4001 C4041_1 C4061 C4045_1 C4046_1 R4008 C4032 C4088 IC4009 C4058 C4059 R4038 R8114 W825 105 R8115 C8122 C8114 C8125 C4050_1 W820 C8119_1 R4071 C4038 C8112 L8104 W824 NTSC PAL W819 IC8102 C8121_1 D8111 D8112 C4037 R4035 R4031 4 IC4002 C4093 C4094 L8102 W818 C8110 C8107 C4015 W826 L8103 C8109 C8104 C8108 W855 C8105 C8106 W860 R4036 R4037 C8111 R4039 C8120 C4086 B8103 R4076 C4025 C4024 R4064 W835 R4059 R4057 W809 W808 C4066 C4023 C4022 C4020 C4019 C4013 C4010 R4073 B4018 B4001 C4030 C4004 W848 R4043 W834 R4022 C4033 B4014 C4002 C4051 B4016 D4002 C2318 R2339 C4027 C4007 D4005 W850 B4008 C4099 C4080 C4097 C4104 C4092 C4065 W837 W838 C2347 B4003 C2326 C4052 C4012 C4075 B2304 B2305 C4036 C4072 C4082 B2303 D4003 C4018 R4014 C4085 C4081C4028 B4010 R4002 X4001 R4001 R4021 R4019 W842 R4020 R4004 R4005 R4003 C4069_1 C2314_1 HS2301 R2338 R2328 C2307 IC2301 R4069 C4060 C4040_1 157 C8113 C8126 R8112 R8113 R2362 W816 C2310_1 R4060 R4062 R2319 D2303 D2304 R2305 R2307 R2335 R2301 R2308 C2304 R2334 R2327 R2324 R2321 CP2302 R2326 R4061 B4009 C4001 R4078 W840 R4077 R4050 R4051 R2306Q8101W814 R2361 W873 D8102 IC2304 C2329_1 R2303
VMD348A
R4042
W836
C4026 R4045
VMD348A
CP8101_2
C2358
C2357
D4004
C4014
Q2305
B4013 C4057 B4012 C4056 B4011 C4003 C2350 R2309 C2342 W810 W807 C2332
W843 R2355 R2348 R2347 Q2304 R2346 C2331 R2318 R2341 C4102 W806 B2302
B2301
F-2
CP601
CD002
CD1702
FH1701 J4202 B8001 D1711 C1714 TP4201 FH1702 R1701 J4201 W026 C1701 D1702 W028 C1710 C1708 C1712 Q1706 D1706 CP1708
R1 71 8
F1701
C005
W007 R4220 C4212_1 CD1703 C4211 C3002_1 R3001 Q3003 L1701 D1717 R1714 W010 R3015 Q1702 CD1704 J8007 C8094_1 L8002 R4209 C4220 R4239 R4205
C4206_1
R353
R1726
D1732
IC3004
W014
C321 Q3014 W027 CP1707 W030 C3005 W025 D3008 W020 W021 W898 Q1705
1
IC3003 D3004
C3023
W016
Q3002
TU001
R359
IC352
C350 R311 W003 HS3001 W041 R3009 C326_1 W047 C3013 W029 C3010 D1715 W345 R1724 D1718 HS1701 C1724 R1721 C1720_2 T1701 W065 R1717 W888 C3012 R1703 D1722 C1713_1 W052 D1716 W042 W043 W036 W044 W037 W045 W039 W040 W073 S801X CP8001 D3003 C1705 CP1702
71
W004 W897 IC3001 D1723 C3008 Q3005 W085 W094 C1733 W089 C1718 C1716 D1704 D1707
CD1705
D3005
C323_1 C315 D1734 C1715 C311_1 W082 C309 R3002 R3003 D3001 C306_1 B1703 D1721 D1726 IC1701 D1727 C1711 C305_1 W343 C310 W058 W086 W035 L1505 R1725 VR1701 D1712 D1724 R1712 R1710 D1703 W050 W049 W056 L3001 W063 W342 W090 D1720 D1733 C1717 C1728_1 IC1702 W088 D1728 R1706 W083 L301 W344 W048 W053 W034 C3028 W074 W071 W072 W078 W075 W080 W076 W077 W894 W069 W084 W339 W809 L4504 W856 Q4505 W341 S809Y R5516 R5511 W062 C4511 C5554 C5536 C5543 C4523_1 C4518 C4539_1 CP4501 W152 C4548 C4544_1 S808X W151 L5503 C4508 W153 C5559 C5533 C5519 C5530 C5526_1 C5502 C4576 C4564_1 C4565_1 C4567 W141 W137 W846 D602 L4509 W183 C103 D601 C4572 W874 W197 W224 W223 W201 W221 W219 R1516 R602 W232 W236 W350 W169 W200 W238 W187 W198 W193 W190 W226 W195 W188 W171 W827
Q101
D106
W033
R1727 W038 D4207 W054 W057 W059 C5555_1 C4529 W877 C5545_2 R5512 W159 W092 W864 R635 W135
02
R3006
W009
W019
R1731
D1709
W060 W108
W046
CP6
W144
W110 W132 C4527 W142 C4540 L4502 W138 W136 W145 C4532_1 W128 D603 W127 W123 R627 W119 W118 W116 W115 W124 Q4504 W126 R605 W892 R613 C624 C603 W120 C4568 W891 X4501 W149 C4545 W121 W122 R4238 L601 W133 W117 W130 D4204 C4566 R4557 C4581 W192 D5502 W234 C4570 R4559 C4574 R4537 C4550 C4558 C4543 W148 C4547 L4506 C5540_1 C5528 L4505 W215 W213 C5564 W208 W870 W209 W250 L5502_1 W129 W359 W205 R4522 C4571 C5544 C5515 C5542 C609 R616 W103 W820 W104 C612 L602 W114 W113 W143 R173 W139 W112 CP603 W111 C1516 L1504 W893 W105
S801Y
S809X
CP8002
S814X
C128
R5524 C5531
SOLDER SIDE
R622
W098
C5525_1 C5520_1 L5501 C5523 C5551 L8001 C5524_1 D5501 W157 C8013 C5512 W146 C5514 C5507 R5501 W261 W272 C5505_1 W834 C5508 D3007 Q3010 R3020
R302
CP
1 10
C1518 W102 C1528 L1501 W174 W164 W181 W175 W165 D605 W166 W161
W099
W158
C8006_1
W217
W257
W247
W255
W207
W277
W248
W242
W273
C126
W256
W243
W167 X601
W245 W244
W211
W246
W173
W186 W184
W252
W859 R4563
W249
W845
W357
L5504
W241
W220
W214
W212 R153
W218
W258
W233
W819
R4562
W196
C104_1 W854
Q103
W251
D3002
C113_1 W163 C632 W185 W170 R632 W352 W194 W202 W179 W180 W289 W282 W278 C122_1 D108 W294 R113 W292 W293 R125 D103 W199 R114 W206 W191 W189 W176 W172 R131 W338 R623 C119_1 W178
W262 W225 W265 W253 W230 W229 W228 W222 S101X W254 W271 W275 W276 C1520
R1519
L8003
X102
X101
C1536 TP5501
Q1
08
Q107
Q1
05
W844
W816
W299
W300
Q104
W330 W841 W842 W301 W314 C141 W309 W308 W307 W315 W312 C139 W358 W321 W316 W331 W332 W333 W335 R4528 W305 W304 W303 S101Y W297 W296 W310 D4201 W806 W306 W311 W328 W318 R144 R8025 W319 W334 C8065 R8024 C8023 C8005 C146 W320 W313
R128
C2210 C2212
R2224
R2212
W838
CP2201
D4205
W337
J2201
J2202
W813
D2206
D2207 OS2201
SW2207
SW2206
SW2204
SW2203
B2201
W880
W259
C8009_1
W268 W263
VMC293C
F-3
1
W150
C1534_1
CP4503
L1502_1
W097 W096
CP303
C320
TH
CP1704 R1722
D1705
C3004_1
D1710
R356
F-4
Q605
R1513 C1523 R1512 R1510 W351 R1507 R1511 C1511 C1507 C1505 Q1503 R618 W361 W360 Q1502 R628 C634 R611 IC1501
R4550
SOLDER SIDE
C4561 R610 C606 R609 R4521 R4519 C4534_1 C4573 Q602 C4569 R607 R4509 R4505
Q4509
C613 R608 C607 R633 R612 R634 R617 C611 C608 17 R110 C118 R115 R116 C618 R615 C619 Q601_1
R147
C4579
R5502
IC1502
W883 Q114 C144 R136 R165 Q110 W851 1 IC103 C8090 R8051 R8056 R8027 C140 R133 C8070 R8054 R8049 R119 R4204 Q106 R123 Q2201 R8023 IC8004 R8050 R8052 R8053
R139
R137 C2201 R2206 R2208 C2205 R152 C143 C2203 R2204 R2203 R2201 R2205 C2202 R2202
R166
10
IC
R101
C1531 Q1501
IC
R1502 R624 C626 C628
R134 1
60
C630 C629 R625 R626 C627 C625 R620 C631
W887
C1538 C4580 R1515 49 Q102 R1504 C1502 C1513 R1506 R1503 C1512 C164 R103 C138 C1537
R171
C616 R159
C137 R636 R148 R1520 Q606 C117 R1509 R108 C110 R106 C109 C604 R104 R164 R630 R160 R149 R150 C114 R177 C116 Q112
C131 C125 C152 C132 C127 C121 C156 C130 R129 C133 R112 C135 C123 R118 R176 51 R132 R135 R111 C111 C154 76 26
01
45
R4540 R4536
IC
F-5
C4213 R8003 C8010 R8005 R4217 C4209 C4214 C4203 W900 Q4212 R1705 Q4203 R8004 Q8002 R4231 C8095 R8013 R4203 R4207 Q4210 Q4211 R4214 C4202 R4232 Q4202 R8006 C004 R8007 C4210 Q4201 C358 R1708 W829 C4208 C3014 C3001 R3024 Q3015 R3017 R301 Q350 R357 Q3011 W811 R307 C302 R3016 W837 C001 Q3009 R3026 R3007 Q3001 R3011 R3018 R3019 C006 Q3006 C318 C3024 C317 W815 C314 C312 R4212 C3027 C8017 W346 W347 W831 R1719 R1713 C8019 C325 C319 C316 IC302 R3025 R3013 R3012 R3027_1 C3003 Q3008 Q3004 R1715 C1722 R3005 R302 C304 C307 R4218 R306 R304 W353 W886 R4216 R4215 IC602 C1525 R1517 R1518 C1504 R603 R4501 R4507 C8020 C8044 Q4204 C4537 R4531 R4527 R4219 Q8006 Q8007 C4542 C4541 R4532 R4533 R4553 Q4511 IC1505 R305 R303 R4511 W804 C5553 C4524 R4520 C5558 C5560 C4517 C4536 C4533 R4526 R4529 C5552 R5513 C5535 R5510 C5534 17 C4514_1 1 C5565 C5557 C5566 C5549 R4513 R5518 R5515 C5541 C5538 R3023 C1709 R1716 R1709 C1703 R1707 C1702 W881
IC
33 C4522_1 21 Q116 R4530 C148 C145 61 C4521 C4505
55
01
49 C5563
C5518
C5529 C5501 41 C5550 R5514 R5519 R4524 C5556 R4539 R4534 C4546 R4541 R4545 C5522_1 R5504 C5517 C4535 C5562 R4523 R4525 C151 R143 R140 R107 C5513 C5509 R5503
VMC293C
C5503
IC1504
C8014 W872 IC199_1 C8079 C8081 R8048 C8064 R8026 R8047 R8020 C8025 C136 R8021 IC8002 C8077
C1532 C1535
C2207
C2209 C2213
F-6
B402 Q403 C415 D415 B401 R414 SW2258 W017 HS401 B403
C408_1 R2257 CC801 R818 D805 C815 C816 D806 D804 CP603B C817 C819 R825 R807 C801 R824 W833 Q805 D801 L804 C818 W018 SW2257 R2256 SW2256 R2255 SW2255 R815 SW2254 R2254 SW2253 R2253 W022 SW2252 W020 W021 R821 TP801 R814 R822 TP803 R816 C445 C430 R820 R439 R453 Q806 TP802 R810 Q804 R806 Q807 R805 D802 D412 R809 D803 R452 R2251 SW2251 CP805 W806 S801 C820 CP001 CD2251 CP604 W014 C418_1 W822 C412 FB401_1
R412_1 C402
F-7
J8
01
CP802B
R819 R808 L403_1 W834 W831 L402 C449 CP404 C406_1 W821 D416 D411 R407 R454 C446 R427 R419
R4 45 _1
W006
R438
2A
W002
W003
CP
80
W004 D402
C436 C434
VR404 R432
W008
C404
R429 R421_1 C423 C432 C427 R405 R401 W807 R403 W830 C403 C421
C414
C443 R428
R424 R415
R447
R444
D413
W007 IC401
CD807
TO VCR DECK
R431
HS402
D419
R430
R442 R406 R441 W015 D404 R418 D410 D418 R417 W009 D414 W011 R443 D417
R440
Q401 C407
D403
CP602B
CD808
TO DVD DECK
F-8
(DVD PCB)
VC OPU_F SPDL_SENS+ OPU_E SLED_PWM TRACK_PWM TRAY_OPEN TRAY_CLOSE MMZ1608R102CT DVD_CD (DVD-L/CD-H) TOUT_SW TIN_SW SPDL_SENSOPU_D DVD_LD CD_LD VR_DVD VR_CD OPU_C OPU_B DRVSB (MUTE-L) OPU_A RF D4001 DUPTD1 LEVEL_CONVERT 1SS355 Q4004 KTC3875S_Y_RTK 3.3 5.2 R4011 10P CH 2.9 4.7K R4013 47K C4043 RX
UNREG+3.8V
FPCSTRB
MMZ1608R102CT
IRRCV
B4013
0.001 B 0.001 B
100P CH
1SS355 DUPRD1
4.7K
47P CH C4091
R4052
0.027 B B4012
C4042
FROM/TO AUDIO/VIDEO SYS_MUTE DAC_VIDEO_C DAC_VIDEO_B DAC_VIDEO_D ASDATA0 ABCLK ALRCLK AMCLK MD MC ML RESET P.CON+A5V P.CON+5V GND D_GND 0.001 B C4102
C4057 180P CH
C4086 C4085
W848 6.3V 100 KA C4070_1 6.3V 220 KA C4071_1 6.3V 47 KA C4068_1 47 KA P.CON+3.3V 0.1 F W834
JG009
C4067_1
0.1 F C4075
4.7K R4038
TP4026
R4036
RFINN RFINP
0.1 F
6.3V
C4072
0.1 F
0.1 F
B4016 MMZ1608R102CT
C4088
C4004
TP4025
W840
C4076
0.1 F
C4051
C4033
C4002 R4061
R4063
R4060 R4062
VDDDAC VDDAFERF
FROM/TO MEMORY
FROM/TO MOTOR DRIVE TRAY_OPEN TRAY_CLOSE HOME TOUT_SW TIN_SW DVD_CD DRVSB RF OPU_A OPU_B OPU_C OPU_D OPU_E OPU_F VC SPDL_SENSSPDL_SENS+ VR_DVD VR_CD DVD_LD CD_LD SPINDLE_PWM SLED_PWM TRACK_PWM FOCUS_PWM P.CON+A5V P.CON+3.3V VCC+9V ADCIN_5 ADCIN_6 ADCIN_7 M_GND D_GND GND 6.3V 47 KA 100P CH C4104 0.001 B TP4012 TP4011 C4036
6
HA0 HA1 HA2 HA3 HA4 HA5 HA6 HA7 HA8 HA9 HA10 HA11 HA12 HA13 HA14 HA15 HA16 HA17 HA18 HA19 HD0 HD1 HD2 HD3 HD4 HD5 HD6 HD7 HD8 HD9 HD10 HD11 HD12 HD13 HD14 HD15 MEMCS0 RD WR SD_A0 SD_A1 SD_A2 SD_A3 SD_A4 SD_A5 SD_A6 SD_A7 SD_A8 SD_A9 SD_A10 3.3 3.3 NC 3.3 3.0 3.0 3.0 3.3 3.3 0 0.5 2.6 0 0 1.9 0 0 0 2.1 2.0 NC 0 3.3 0.6 3.3 2.6 1.8 2.7 2.9 0 0 0.5 0 0 0.6 0 0.6 2.7 2.7 0.6 0.4 5.5 3.3 0.4 3.3 0 0 0 3.1 3.1 3.2 0 3.3 3.3
0 0 3.3 3.2 0 0 3.3 1.8 0 0 2.3 3.3 0 0.2 1.3 1.3 2.1 2.1 2.1 2.1 0 2.0 2.1 2.1 2.1 3.3 3.3 2.1 3.3 2.1 2.1 1.3 1.3
DUPTD0 DUPRD0 PWMCO(0) IDGPCI/O(4) GPCI/O(46) VDDPWM PWMCO(4) GNDPWM PWMCO(3) PWMCO(2) SPINDLEPULSE SLEDPULSE VDD-IP ICGPI/O(7) ICGPI/O(6) GNDP IDGPCI/O(3) VDDP ICGPCI/O(5) ICGPCI/O(4) GNDC GPCI/O(32) VDDC AGND1 AGNDREF DVD_LD CD_LD DVD_MD CD_MD RESOUT VBGAP VC F K E AGND J D H C AVDD SVDD B AVDD1
208 207 206 205 204 203 202 201 200 199 198 197 196 195 194 193 192 191 190 189 188 187 186 185 184 183 182 181 180 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163 162 161 160 159 158 157
0.1 F R4045
HA15 HA16 HA14 HA13 HA12 HD15 HA11 HD7 HA10 HD14 HA9 HD6 HA8 HD13 HD5
C4008 0.1
R4012
HD12 WR HD4 HD11 HD3 HA19 HD10 HA18 HD2 HA17 HD9 HA7 HD1 HA6 HD8 HA5 HD0 HA4 RD HA3 HA2 MEMCS0 HA1 HA0 BOOTSEL1
C4010 0.1
C4013 0.1
0.01 B
0.01 B
TP4010 W842 C4029 0.1 F JG021 R4073 R4076 C4031 33 33 0.01 B IAMCLK IABCLK IALRCLK JG024 R4058 TP4015 TP4016 C4098 B4010 R4071 10P CH 220 ASDATA0 4 SPDIF R4025 R4026 R4027 220 STBY_L
R4031 R4035
4.7K 4.7K
0.1 B
C4014 0.1 F
C4083_1
C4077
C4082
C4018
C4019
C4020
C4024
C4023
C4025
C4011_1
100 KA
R4059
6.3V
0.1
6.3V
C4052
C4053_1
100 KA
0.1
C4009_1
47 KA
C4015
47K
UNREG+3.8V
R4070
SD_D0 SD_D1 SD_D2 SD_D3 SD_D4 SD_D5 SD_D6 SD_D7 SD_D8 SD_D9 SD_D10 SD_D11 SD_D12 SD_D13 SD_D14 SD_D15 RAMCS0# RAMCS1# RAMRAS# RAMCAS# SD_BA0 RAMDQM RAMWE# RAMCLK
R4080 R4009
C4090
C4089
C4026
61 62 63 64 65 66
BOOTSEL2
0.9 0.3 1.0 0 1.0 3.3 0 1.0 0.2 0 0.2 1.8 1.9 0 0.2 3.3 0 3.1 0.5 0 3.1 0.2 3.2 3.3 3.2 0 0 1.5 3.3 2.1 0 1.3 0.8 0.8 3.3 1.7 1.3 0.5 0 0.9 1.8 1.4 0 0.5 3.3 2.0 0.4 1.5 0 0.8 1.2 1.5
NC
UNREG+3.8V
0.1 F
0.1 F
0.1 F
0.1 F
0.1 F
100 KA
0.1 F
100
C4080
C4100
SSCRXD MEMCS(1) VDDP MEMAD(15) MEMAD(16) MEMAD(14) MEMAD(13) MEMAD(12) MEMDA(15) MEMAD(11) MEMDA(7) GNDP MEMAD(10) MEMDA(14) MEMAD(9) MEMDA(6) MEMAD(8) MEMDA(13) MEMDA(5) MEMAD(20) VDDP MEMDA(12) MEMWR# MEMDA(4) VDDC MEMDA(11) MEMDA(3) MEMAD(19) GNDC MEMDA(10) MEMAD(18) GNDP MEMDA(2) MEMAD(17) MEMDA(9) MEMAD(7) MEMDA(1) MEMAD(6) MEMDA(8) MEMAD(5) VDDP MEMDA(0) MEMAD(4) MEMRD# MEMAD(3) MEMAD(2) MEMCS(0)# MEMAD(1) MEMAD(0) GNDP VDD-IP VDDP 53 54 55 56 57 58 59 60
75 +-1% R4004
75 +-1% R4003
75 +-1% R4002
RAMADD(6) VDDP RAMADD(1) RAMADD(7) RAMADD(0) GNDP RAMADD(8) VDDC RAMADD(10) GNDC RAMADD(9) VDDP RAMADD(11) RAMCS(0)# RAMBA(1) RAMBA(0) GNDP RAMCS(1)# RAMRAS# RAMCAS# VDDP RAMWE# RAMDQM GNDPCLK PCLK VDDPCLK RAMDAT(8) GNDP RAMDAT(7) RAMDAT(9) RAMDAT(6) VDDP RAMDAT(10) RAMDAT(5) RAMDAT(11) GNDP RAMDAT(4) VDDC RAMDAT(12) GNDC RAMDAT(3) VDDP RAMDAT(13) RAMDAT(2)
0 TP4019 0 W836 1.6 1.6 R4042 120 1.8 3.3 C4069_1 0 6.3V 47 KA 0 3.3 3.3 HOME PM16 3.3 (MIC_DET) 3.3 NC (DJTDO) 0 I2C_CLK 0 I2C_DAT 1.8 0 (ICETCK) 3.3 (ICETDO) 3.3 (MUTEC) 3.3 (ICETMS) 3.3 3.3 (PM11) 0 TP4017 TP4018 3.3 R4024 3.3 4.7K 1.7 0 1.7 1.6 0 1.1 0 ASDATA1 0 ASDATA2 1.6 0 MIC_ON 0 NC 0 0 3.3
27MHz X4001 100BT02701 C4028 0.1 F C4027 0.1 F JG028 R4019 R4020 R4021 C4030 0.1 F
1M
C4034
75 +-1%
208 SSCTXD
GNDDACBS2 GNDDACP RSET C/B/U VDDDAC Y/R/V CVBS/C VDDDAC 160 A CVBS/G/Y 159 G Y/C 158 RFN GNDDACD GNDDACD 157 RFP GCLK XO VDDA RESET# GNDA GNDP VDDP IDGPCI/O(2) GPCI/O(31) DJTCK / ICGPCI/O(3) / VID(0) DJTO / GPCI/O(30) / VID(1) DJTDI / GPCI/O(29) / VID(2) DJTMS / GPCI/O(28) / VID(3) MPEG/MICON/DSP/RF_AMP IC VDDC GNDC IC4001 GPCI/O(27) ZR36862PQCG IDGPI/O(1) ICGPCI/O(2) GPCI/O(26) VDDP ICGPCI/O(1) GNDP HSYNC VSYNC AIN VDDP-A2 AMCLK 100 RAMDAT(14) GNDP-A2 101 GNDP ABCLK ALRCLK 102 RAMDAT(1) GPAI/O 103 RAMDAT(15) AOUT(0) AOUT(1) 104 RAMDAT(0) AOUT(2) SPDIF IDGPCI/O(0) ICGPCI/O(0) GNDP GPCI/O(20) VDDP 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104
52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
R4005
C4035 24P CH
L4002 W5T29X7.5X19
33 33 33
TP4008
FROM/TO DVD IN/OUT DVD/VR 130mm DVD COMBO 250mm CD4002 (CP8001) C32B3303 GND(D) GND(D) TX 1 2 3 4 5 6 7 8 9 10 11
CH C4093
C4037
0.1 F
3.2
3.2
SDA
SCL
WP
VCC
C4084_1
C4097 C4065
100P
C4094
GND 4 0
NC 3 0
NC 2 0
NC 1 0
P.CON+A5V P.CON+5V
L4001 2.2uH 0305 TP4027 10V 100 KA 10V 100 KA 10V 100 KA TP4028
REG+3.3V +1.9V IC IC4003 BA33E00WHFP-TR EN 1 VCC2 2 VCC1 3 GND 8 4 VO1 5 VO2 6 ADJ 7
SPDIF
R4014
4.7K
0.01 B
6.3V
C4012
0.1 F
6.3V
16V
0.1
RAMCS0# SD_BA0
RAMWE# RAMDQM
RAMCLK
SD_D12
SD_D8
SD_A10
SD_D4
SD_D3
SD_A8
SD_A9
TP4003
PCB130 VMD348
1
NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK. NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
G-1
G-2
FROM/TO MPEG/MICON/DSP 16M SDRAM IC IC4008 K4S161622H-UC60 SD_A0 SD_A1 SD_A2 SD_A3 SD_A4 SD_A5 SD_A6 SD_A7 SD_A8 SD_A9 SD_A10 SD_D0 SD_D1 SD_D2 SD_D3 SD_D4 SD_D5 SD_D6 SD_D7 SD_D8 SD_D9 SD_D10 SD_D11 SD_D12 SD_D13 SD_D14 SD_D15 RAMCS0# RAMCS1# RAMRAS# RAMCAS# SD_BA0 RAMDQM RAMWE# RAMCLK HA0 HA1 HA2 HA3 HA4 HA5 HA6 HA7 HA8 HA9 HA10 HA11 HA12 HA13 HA14 HA15 HA16 HA17 HA18 HA19 HD0 HD1 HD2 HD3 HD4 HD5 HD6 HD7 HD8 HD9 HD10 HD11 HD12 HD13 HD14 HD15 MEMCS0 RD WR P.CON+3.3V C4095 FLASH IC 8M IC4007 SST39VF800A-70-4C-EKE 48 1 HA16 C4064 0.1 F 46 3 0 0.7 1.9 1.3 1.2 0.6 0.7 0.8 1.6 C4062 0.1 F HD11 HD3 HD10 HD2 HD9 HD1 HD8 HD0 RD 1.6 1.6 1.3 1.2 1.4 1.4 0.9 1.6 2.6 0 2.6 2.5 R4040 4.7K 3.3 GND DQ15 DQ7 DQ14 DQ6 DQ13 DQ5 DQ12 DQ4 VCC DQ11 DQ3 DQ10 DQ2 DQ9 DQ1 DQ8 DQ0 OE# GND CE# A0 A13 A12 A11 A10 A9 A8 A19 A20 WE# RP# VPP WP# A19 A18 A17 A7 A6 A5 A4 A3 A2 A1 0.8 1.5 2.5 1.3 1.6 1.5 0 40 9 0 39 10 11 40 DQ9 DQ8 VDDQ NC UDQM CLK CKE NC A9 A8 A7 A6 A5 A4 VSS DQ6 DQ7 VDDQ LDQM /WE /CAS /RAS /CS BA A10/AP A0 A1 A2 A3 VDD 40 DQ9 DQ8 VDDQ NC UDQM CLK CKE NC A9 A8 A7 A6 A5 A4 VSS DQ6 DQ7 VDDQ LDQM /WE /CAS /RAS /CS BA A10/AP A0 A1 A2 A3 VDD 11 NC 3.3 0 37 12 0.1 36 13 0.1 35 14 C4039 0.1 F R4041 RAMDQM 4.7K 0 34 15 W838 HA19 HA18 HA17 HA7 HA6 HA5 HA4 HA3 HA2 HA1 RAMCLK2 5 R4057 17 34 47K 18 33 RAMCKE NC 1.4 1.6 1.6 1.3 1.7 2.5 1.6 SD_A9 SD_A8 SD_A7 SD_A6 SD_A5 SD_A4 RAMCS0# SD_BA0 SD_A10 SD_A0 SD_A1 SD_A2 SD_A3 C4087 26 25 26 0.1 F 25 SD_A9 SD_A8 SD_A7 SD_A6 SD_A5 SD_A4 WR RESET SD_D9 SD_D8 C4058 13 38 0.1 F 14 37 NC SD_D6 SD_D7 C4074 0.1 F RAMDQM RAMWE# RAMCAS# RAMRAS# RAMDQM RAMCLK W835 RAMCLK2 RAMCKE R4048_1 47K 33 18 NC RAMCS1# SD_BA0 SD_A10 SD_A0 SD_A1 SD_A2 SD_A3 C4047_1 0.1 F 34 17 SD_D9 SD_D8 C4041_1 0.1 F 37 14 NC 38 13 SD_D6 SD_D7 C4046_1 0.1 F RAMDQM W837 HA13 HA12 HA11 HA10 HA9 HA8 HA19 1.2 3.3 A16 VCCQ A15 A14 1.7 1.0 HA15 HA14 SD_D15 SD_D14 C4060 50 VSS DQ15 DQ14 VSSQ DQ13 DQ12 VDDQ DQ11 DQ10 VSSQ VDD DQ0 DQ1 VSSQ DQ2 DQ3 VDDQ DQ4 DQ5 VSSQ 50 VSS DQ15 DQ14 VSSQ DQ13 DQ12 VDDQ DQ11 DQ10 VSSQ VDD DQ0 DQ1 VSSQ DQ2 DQ3 VDDQ DQ4 DQ5 VSSQ 1 0.1 F 49 49 2 2 SD_D0 SD_D1 SD_D15 SD_D14 1 16M SDRAM IC IC4009 K4S161622H-UC60
47
48
48
47
47
45
46
46
44
45
45
43
C4040_1 44 0.1 F 43 8 7
SD_D12
SD_D3
SD_D12
SD_D13
SD_D2
SD_D13
42
6
9 SD_D5
41
42
10
42
41
38
11
12
41
39
39
12
10
5
15 RAMWE# RAMCAS# RAMRAS#
36
15
16
36
35
33
16
1.6 0.7
32
31
18
17
19
35
32
30
19
20
32
31
29
20
31
20
19
16
30
21
30
28
21
22
29
27
22
23
29
28
26
23
24
27
25
24
HA0
27
24
FLASHCS
28
23
22
21
3
6.3V 220 KA 6.3V 100 KA 6.3V 100 KA C4063 C4044 C4021
0.01 B
C4099 R4044
D_GND
NC
DEBUG MODE
2
W854
4.7K
0.01 B
MEMCS0
PCB130 VMD348
1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
G-3
G-4
A
NC 4 3 2 + +VS + 5 6 7 R2361 2.2K R2362 3.3K 1 OPE AMP IC IC2304 BA10358FV-E2 -VS
8 W849 W847
2.1V
C2350
DM3P(05SD)
7
FROM/TO LOADER CP2301 09-5000-024-001-001 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 GND F Vref VCC E D C SW1(DVD/CD) VRF(RF_OUT) B A VR(DVD) VR COM VR(CD) GND LD(CD) PD/GND LD(DVD) GND NC T DRV T RTN F DRV F RTN NC
B C2329_1 1K 6.3V 47 KA C2331 R2360 0.1 B JG012 OPU_E JG014 OPU_D JG013 OPU_C JG040 DVD/CD RF JG016 OPU_B JG011 OPU_A JG010 C2328_1 DVD/VR 0.1 F 0.1 F C2309 C2316 6.3V 47 KA C2348 0.1 B JG015 OPU_F 33 R2355
82
R2359
R2356
82
DVD_CD DVD_LD CD_LD VR_DVD VR_CD RF OPU_A OPU_B OPU_C OPU_D OPU_E OPU_F VC HOME GND D_GND 0.001 B C2318 TOUT_SW TIN_SW P.CON+A5V TRACK_PWM FOCUS_PWM P.CON+3.3V R2336 390
CD_LD
0.1 F C2342
C2343_1
0.1 F
0.1
W843
0 0.7 0 R2347 3.3K DVD/CD CTL Q2304 KTC3875S_Y_RTK FOCUS_PWM C2327_1 C2326 R2306 6.8 R2318 F TRACK_PWM
6
DRVSB
R2339 1.2K SPINDLE_PWM SLED_PWM ADCIN_7 ADCIN_5 ADCIN_6 VCC+9V TP2320 M_GND SPDL_SENS+ R2334 10K SPDL_SENSTP2323 TRAY_CLOSE R2324 1K R2319 56K TP2324 3.3K TRAY_OPEN
CDLD DVDLD JG056 TR+ TRFO+ FODVD LD CTL Q2301 2.6 2SA1036K 2.3 JG017 JG018 47 KA
10K
1.9
R2308
22 23 24
6.3V
0.1
TP2322
R2301
C2340_1 TP2303 MOT_LDMOT_LD+ R2353 100 R2352 100 R2350 4.7K R2351 4.7K TP2305 TP2304 P.CON+3.3V 100P CH 100P CH TOUT_SW TIN_SW DVDLD B2301 MMZ1608R102CT C2341_1 CDLD B2302 MMZ1608R102CT 0 CD LD CTL Q2302 2SA2048 3.0 6.3V 100 KA
1K
VC2 HS76 HS2301 763WSAA023 R2321 R2326 TP2319 10K TP2318 5.6K TP2321 R2327 R2305 4.7K R2335
R2338 6.3V 100 KA R2333 220 3.2 R2340 6.8 R2341 JG019 6.8 TP2308 MOTOR DRIVE IC IC2301 LA6565-TE-L-E W816 12K
NC NC NC NC NC NC 0 4.0 2.6 2.6 1.5 1.5 1.6 1.5 0 0 1.0 2.5 4.2 0 1.5 1.5 1.7 1.5 1.5 36 35 34 33 32 31 30 29 28 38 27 26 25 24 23 22 21 20 19 VCONT MUTE1 VREF-OUT MUTE234 S-GND REG-OUT VIN+OP VO_OP VIN4VIN-OP VREF-IN VIN3REG-IN VIN2VIN4 VIN3 VIN2 VIN2+ R2337 10K
27K
100 +-1%
R2307
R2309
75K
100P CH C2358
100P CH C2360
R2342
4.7K
VIN1+A
VCCS
C2357
C2359
VCC2
VCC1
VLD+
VD4+
VD3+
VD2+
VD1+
VLD-
VD4-
VD3-
VD2-
VD1-
FWD
REV
VIN 1
VIN1-A
1 0
5 TP2309
6 TP2310
7 TP2311
8 4.1 TP2312
37
10 TP2314
11 TP2315
12
13
14
15
16
17
18
3 2 1
TP2316
1K
C2306 0.1 F
C2314_1
C2310_1
D2303 1SS355
2
MOT_SPDL+ MOT_SPDLMOT_SLEDCD_LD_CTL MOT_LD+ MOT_LD-
C2304
0.022
MOT_SLED+
TR+
FO+
TR-
FO-
PCB130 VMD348
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
G-5
G-6
(DVD PCB)
1
C/B/U DAC_C_VIDEO 8 Y/R/V 9 W818 FROM/TO MPEG/MICON/DSP CVBS/C 10 DAC_D_DVD_VIDEO DAC_B_VIDEO
2 G R B
3 Y C
4 V U
A B C D
P.CON+A5V
Y V U C
CVBS Y
7
150P CH
150P CH
C8104
C8106
DAC_VIDEO_C
6
RESET MC MD ML AMCLK ABCLK ALRCLK ASDATA0 SYS_MUTE GND
DAC_VIDEO_B 150P CH
470
6
0.2 W814 3.1 0 FROM/TO DVD IN/OUT TP8101 DVD/VR 95mm DVD COMBO 180mm CP8101_2 (CP8002) IMSA-9604S-12F W825 TP8106 W826 TP8107 TP8108 W824 TP8109 TP8110 TP8111 TP8112 TP8113 TP8114 DVD-H(GND) DVD RESET ZERO AUDIO-R GND AUDIO-L GND Y GND C GND CVBS 12 11 10 9 8 7 6 5 4 3 2 1
C8107
DAC_VIDEO_D 100P CH
C8109
C8110
W808
W855
W860
W809
D8111
1SS355
D_GND DAC_B_VIDEO DAC_C_VIDEO C8119_1 100 KA DAC_D_DVD_VIDEO 0.001 B R8114 C8122 D8112 1SS355
C8120
0.1
6.3V
R8115
4
RESET
100K
TO MEMORY
100K
SYS_MUTE
1 B C8126 1 B
CD_LD_CTL RF_GND
3
2.4 STEREO DAC IC IC8102 PCM1753DBQR 8 VOUTR 2.5 7 VOUTL 4.9 6 VCC 3.3
ZEROR/ZEROA
ZEROL/NA
VCOM
AGND
9 0 2.4
10 3.3
11 0
12 NC
13 0
14 15 16 0 3.3 1.7
25V 10 KA
C8121_1
SCK
MD
MC
ML
2
ASDATA0 ALRCLK AMCLK ABCLK
ZERO
MD
MC
ML
PCB130 VMD348
R.SIGNAL + COMPONENT SIGNAL(U) B.SIGNAL + COMPONENT SIGNAL(V) AUDIO SIGNAL(PB) PLAYBACK VIDEO SIGNAL
A B C
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
G-7
G-8
(VCR PCB)
P.CON+5V_A FSC
1/4W
R4523
22K
22K
BUFFER Q4507 2SC2412K 47uH 0305 R4537 1.8K 1/4W 4.0 50V 1 KA 6.3V 47 KA 12 R4541 5.0 3.4
R4545
R4528
3.3K
L4506
R4525
R4530
W854
12K
R4506
L4505
12K
47uH 0305
1K
47K
0.1
C4543
50V 1 KA
1.8K
C4556
P.CON+8V P.CON+5V_A
R4524
C4538
0.01 B
C4545
S808X
S808Y
W880
NC
0.1
C4535
C4547
C4558 6.3V 47 KA C4555 B 0.1 0.022 R4544 50V 1 KA 680K B C4561 0.01 B FROM/TO MICON Y/C_CLK Y/C_DATA Y/C_CS C4559 2.2K 1/4W 0.1 B NC R4559 0 2.2 0.8 43 42 41
4Fsc PLL OUT AUTO-BIAS VSS CLAMP CLOCK 0 VSS
C4546
R4534
R4539
HF2 HF_COM HF1 Y/C/AUDIO/HEAD AMP IC IC4501 LA71205M-MPB 0.5 60 C4521 0.068 B C4522_1 C4514_1 0.047 B 0.047 B 2.2 61 0 62 4.0 63 1.8 64 0.7 65
P
1.5K
FSC
8.2K
C4549
0.022
100CT3R502 3.579545MHz
X4501
C4550
H.SW VIDEO_OUT ENV_DET VCR_A_MUTE CTL+ CTLC_ROTARY DUMMY_V.SYNC V.REC_ST_H R4557 C4565_1 82K 1/4W R4560 100K C4570 C4566 50V 1 KA C4569 0.1 B C4567 FROM DVD IN/OUT 50V 0.22 KA C4564_1 10V 33 KA FROM/TO DIGITAL COMB FILTER C4576 DVD_VIDEO 50V 1 KA 50V 4.7 KA C4572 TUNER_VIDEO 50V 1 KA V.SYNC W870 AUX_V[F/R] FROM CHROMA/IF C4574 50V 1 KA H.AMP_SW1 COMP Y/C_VIDEO
6
FROM/TO CYL CP4501 TOC-C09X-A1 9 8 7 6 5 4 3 2 HF1 (R) HF COM HF2 (L) SP-CH1 (R) SP COM SP-CH2 (L) EP/LP-CH1 (R) EP/LP COM EP/LP-CH2 (L)
2.8 59
0 58
0 57
0 4.8 4.8 4.8 5.0 1.9 2.6 4.0 3.3 3.3 2.3 5.0 5.0 56 55 54 53 52 51 50 49 48 47 46 45 44
SERAIL DECODER C-VCC VX01 320FH VCO
P R
OUT ENV COMP DET KILL DET HA GND CHROMA DET ACC DET
SLD
40
ALWAYS VDD 5V
1.7
TIMMING DRIVER CCD
BGA BGA
OUT
39 0 38 3.0 37 2.8 36
REC APC
PB APC
REC AFC
2.3
BEFORE
IN
AFTER
0.7 66
R H
P R
BGA
R P
35
VCA
0.7 67
P
5
FROM/TO TV POWER GND
3.58M BPF2 Main CONV B-UP AMP ACC AMP ACC DET
68
P.CON+5V_A
W891 47 KA C4508
5.0
HA VCC
C-LPF
1.7 69
P
C4505
R4513
1.2K +-1%
0.33
1.8 70 0 71 2.0 72
P H L R
+
PB-C
1 2 3
32 4.0
REG 4V
3.58M BPF1
6.3V
YNR/COMB
P R R
VIDEO AGC
CLAMP
P
2.0 73
PB-C
1/2 FBC
R P R P
BAL TC1
NL EMPHA FM MOD
R-EQ TEST NORMAL
Y-LPF
R
74
2.0
P
Y/C MIX
0 75
A-GND
1 2 3
2.2 76 4.9 77
A-VCC ALC DET PB,EE EQ AMP SP,LP PB,EE REC:LP<EP PB:EP VREF REC AMP MUTE
P R
DOUBBLE LIM
FM DEM
26 3.6 NC 0 4.9 L4509 P.CON+5V_A R4550 2.2M BUFFER Q4511 2SA1037AK R4553 11 R4562 100uH 1/4W 0607 Y/C_VIDEO 25
ALC
R P
LPF
LINE AMP
24
Y-VCC
100
180 1/4W
NORMAL_A
R4504 12K
0.1 R4512 10
2 2.3 0.1 B
3 2.2
4 2.2
5 2.5
6 2.3 C4541
7 2.2 0.0022 B
8 2.3 R4533
9 2.4 820
10 5.0
11 1.0
12 1.0
13 1.7 13
14 1.4
15
16 0
17 0 NC 1.5 C4551
18 0.1
19 2.2
20
180
C4524
FM AGC FIL
Y-GND
4.7K
5.0 0 5.0
FROM/TO HEAD AUDIO CONTROL P.CON+5V_A CP4502 IMSA-9604S-06C 6 5 4 3 2 1 AUDIO REC AUDIO PB CTL+ CTLAE HEAD(+) AE HEAD(-) 0 AUDIO PB SW Q4501 KTC3875S_Y_RTK 0.7 0 0 AUDIO PB SW Q4502 KTC3875S_Y_RTK 0.7 R4503 10K CTL+ CTLR4501 15 560 R4502 V.REC_ST_H W846 0
1/4W
R4563
100 TP4501
R4540
R4520
V.ENV
C4544_1
4.7 KA
5.2 COIL,BIAS OSC L4502 5.3 1626009 6 5 4 MMTS 1 2 3 0.01 B R4508 220 YK C4512 100uH 0305 3.3K
C4580 0.1 B
R4532 22K
50V
R4509 680 L4504 BIAS CTL Q4505 KTA1266 0 4.9 4.9 R4511 22K 4.8
C4548
C4571
R4527 330K 0 0 AMP Q4506 2SC2412K R4519 C4534_1 0.0047 B R4522 5.6K R4507 1M R4521 10M C4537 0.01 B C4540
2.7K
R4546
39P CH
150P CH
C4553
C4557
6.3V
CD4501 2F061502
C4506_1
25V 10 KA
C4539_1
10K
0 0 0.015 B R4510
0.022
6.3V C4513
0.0047
C4511
14
R4531
100V
180
V.SYNC
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
RECORD LUMINANCE SIGNAL RECORD COLOR SIGNAL PLAYBACK COLOR SIGNAL PLAYBACK LUMINANCE SIGNAL
H
G-9
G-10
(VCR PCB)
8
8
FROM/TO REGULATOR VIDEO_OUT 0.022 B CENT_LED_CTL CONTROL_IN SDA SCL CYL_DRIVE H.SYNC V.SYNC BACKUP+5V AT+5V DVD_H VCR_POWER_H AT+12V P.CON+5V_C P.CON+5V_A Y/C_VIDEO 100P CH HIFI_H.SW DVD_H R111 AT+5V 4.7K C148 C151 SCL 5.0 EEP ROM IC IC199_1 BR24L04F-WE2 8 VCC 0 7 TEST 4.8 6 SCL A1 C133 C130 X101 15P CH 100DA32R01 C131 32.768KHz 15P CH C132 0.1 B AV_SW2 SDA 4.8 5 SDA A0
P.CON+5V_A
C121
28 W859 150P CH
1/4W 5.6K
C137
0.18 B R131
C152
10P CH C135
C138
10K
1.6
R134
A2
5.6K C126
VSS
330K
R132
56K
R129 1M
1 0 0
2 0
3 0
R139
27 10V 100 KA C125 FROM/TO Y/C/AUDIO/HEAD AMP Y/C_VIDEO Y/C_CLK Y/C_DATA Y/C_CS H.SW VIDEO_OUT ENV_DET VCR_A_MUTE CTL+ CTLC_ROTARY DUMMY_V.SYNC V.REC_ST_H H.AMP_SW1 COMP VCR_A_MUTE C114 TV_POWER_H 0.01 B R112 100 0.1 B
R135
10K
10K
R141
47K
DRUM_PWM
NC NC NC NC NC NC 2.2 1.6 0 0 4.7 4.9 0 0 5.0 3.3 1.0 0 0 0 5.0 4.9 3.6 3.6 2.7 0 0 5.0 5.0 0 3.5 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 CAP_PWM CENT_LED_CTL DVD_H AV_SW2 HSYNC CAP_FULL OSCO VSYNC VDD NC NC XO CVIN VSS2 VSS OSCI NC NC CVIN2 SXI NC NC XI
R147
C154
47K
0.001
FROM/TO DVD IN/OUT TX RESET DUMMY_V.SYNC R153 1K 1/4W R144 1K 1/4W H.SW IIC_OFF CAP_LIMIT TV_A_MUTE 16 H.SW TP102 NC RX DVD_RESET AV_SW1 FROM/TO IN/OUT KEY_B KEY_A REC_LED T-REC_LED W841 W842 SCL SDA TX RX REMOCON_IN EXT_A_MUTE VCR_A_MUTE EXT_MUTE TV_POWER_H FROM/TO CHROMA/IF Y/C_DATA Y/C_CS Y/C_CLK OSD_R OSD_G OSD_B OSD_Y EXT_A_MUTE TV_POWER_H V.SYNC H_CONTROL AV_SW1 EXT_MUTE R152 REMOCON_IN H.SYNC SDA SCL VCR_POWER_H PROTECT IIC_OFF EMERGENCY
53
54
VCR.A.MUTE FSCLPF TV_POWER_ON-H VM_OSD_SW CYL_SPEED_UP BLK DEGAUSS R G B CAP_F/R CYL_FG/PG H_CTL FGF 98:C_ROTARY 99:H.AMP.SW1 100:COMP 76:CO CHROMA_POWER_ON_H 77: NC VCR_POWER_ON-H V.REC.START-H REC/OTR_LED SYSCON/TIMER/SERVO IC IC101 OEC8078A 51: VDD2 52: AFCC 25:RESET 24:DUMMY.V.SYNC
IIC_OFF CAP_LIMIT TV_MUTE TUNER_H SCL SDA TX RX TV/DVD_LED Y/C_DATA Y/C_CS Y/C_CLK RENT_H EXT_A_MUTE FF/REW_L AV_SW1 EXT_MUTE REMOCON IN REEL-S REEL-T TAB_SW
22
2.2K
AFCLPF
H.SW
23
0.0022 B
R118 1
52
24
C116
C123 2.5
51
25
5.1
5.0 0.1 3.5 5.0 3.6 0 R140 4.7K R143 4.7K 0 4.8 4.8 0 0 0 NC 5.0 0.1 5.0 0 0 4.9 0 0.4 5.0 2.4 2.4 0 5.0 W806 REEL-S REEL-T 0 5.1 0 AV_SW Q116 2SC2412K NC R107 4.7K S101Y
56
55
62
C110 OSDB
5
0.001 B C107 D101 LTE-3271T-012A-O BOT SENSOR 5.0 Q101 ST-304L 0 0.001 B C101 EOT SENSOR Q103 ST-304L 5.0
0.0047 B CAP_F/R CYL_FG/PG R108 1K C109 EOT BOT R106 C113_1 1K 25V 10 KA 0.1 B C111 C117 0.01 B CTL+ 0.001 B R110 C118 10K C122_1 270K R105 0.0039 B C119_1 25V 10 KA 17 H_CONTROL
63
13
14
OSDG
61
15
OSDR
60
16
DEGAUSS_H
59
17
OSD_Y
2.2M 1/4W
58
18
CYL_DRIVE
R114
57
19
20
21
65
64
66
67
68
69
70
6.3V 100 KA
R103
270
71
C102
0 2.5
AVSS CTLA
2.5
VRI
2.5
VRO
3.3
10
11
12
73
EMERGENCY
MSSEN_B
MSSEN_A
LDM_CTL
HIFI_ENV
ENV.DET
KEY_A
BOT
EOT
75
CTL(-)
AFT
R116 560
76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 2.5 0 2.6 0.1 5.1 5.1 4.9 4.9 0 2.6 2.4 0 3.4 3.6 0 0 5.0 0 0.1 0 0 0 3.5 4.9 0 NC
B W845 0.027 B C164 C143
4.9
560
2.4
KEY_B
CENT_LED_CTL
CTL(+)
PROTECT
74
POWER_FAIL
2.4
T-REC_LED
R115
DVD_RESET
ST_SELECT
R101
72
22K
270K
10V 33 KA 5.0
AVDD
22P CH
1K R166 6.3V 220 YK C146 BUFFER Q114 2SA1037AK 5.1 R119 2.2K 5.1 4.4 W883 10K D106
C120
R124
1K 1/2W 16V 22 KA
10K
AT+5V
16V 47 YK
10K 1/4W
R128
VCR_POWER_H
C103
FROM/TO CAPSTAN DD UNIT CP101 TMC-J12P-B2 1 2 3 4 5 6 7 8 9 CAP FG CAP VCO VCC CAP.M F/R I LIMIT MOTOR GND GND LD/CY VCO CAP CTL LDM CTL CYL FG/PG CYL CTL
0 SW Q106 DTC124EKA 0
C104_1
4.9
POWER_FAIL MTZJ15B
R137 C144 0.1 B V.REC_ST_H H.AMP_SW1 DVD_RESET C_ROTARY PROTECT 4.7K COMP 5.0
EMERGENCY
ST_SELECT
MS_SEN-B
MS_SEN-A
T-REC_LED
ENV_DET
LDM_CTL
HIFI_ENV
REC_LED
TAB_SW
KEY_A
KEY_B
EOT
AFT
BOT
SW Q110 DTC114EKA
R165 4.7K
FROM/TO SOUND AMP/SURROUND TV_POWER_H OSD_R TV_A_MUTE SCL SDA FROM/TO DIGITAL COMB FILTER AV_SW1 AV_SW2 SDA SCL AFT FROM/TO TV POWER GND DEGAUSS_H POWER_FAIL MOTOR_GND
R104 3.3K
BACKUP+5V RESET
CONTROL_IN 47K 1/4W 120 1/4W R123 R125 LDM_CTL CYL_FG/PG CYL_DRIVE 0.022 B R122 MS_SEN A Q105 RPI-352C40N 5.1 2 0.9 2 3 5.1 2.4 R133 REEL SENSOR Q108 RPI-303 MTZJ5.6B D103 0 1 2 2.4 470 YK 27K 1SS133 D102 C141 NC 5 NC
10 11 12
47K
NC
C106
6.8K
5.1 3
R136
1.2
6.3V
OUT 1 5.2
IN 2 5.1
GND 3 0
D105
1SS133
1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
25V 47 YK
5.1
PCB010 VMC293
C139
NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
RECORD LUMINANCE SIGNAL CYLINDER APC SIGNAL TUNER VIDEO SIGNAL RECORD COLOR SIGNAL
F
G-11
G-12
(VCR PCB)
FROM CRT CP2201 (CD2251) A2001WV2-2P 2 1 GND KEY-B KEY_B
7
POWER_LED_SW Q2202 DTC114EKA 0 0 4.7 LTL-1CHEE-002A T-REC D2206 LTL-1CHEE-002A POWER D2207
FROM/TO SOUND AMP/SURROUND SOUND_R+ SOUND_L+ SP_OUT_R SP_OUT_L 0 REC LED SW Q2201 DTC114EKA 3.9 0 T-REC LED SW Q2203 DTC114EKA 0 3.9
LTL-1CHEE-002A
R8005
220
R8006 B8001 W4BRH3.5X6X1.0X2 COAXIAL J8007 MSP-251V-05NI-FE-LF 1 2 H E C8010 0.1 F R8004 68 1.5 1.7 R8003 D AUDIO DRIVER Q8002 2SC2412K 100K 5.1 R8013
6
FROM REGULATOR AT+5V P.CON+5V P.CON+8V
REC_LED T-REC_LED
REC/OTR D2205
3.3K
6
1.5K R8007
270 1/4W
270 1/4W
R2223
R2224
TV_POWER_H
270 1/4W
R2227
C8095 0.022 B FROM/TO MICON R2205 KEY_B SW2201 EVQ21505R SW2202 EVQ21505R SW2203 EVQ21505R SW2204 EVQ21505R SW2205 EVQ21505R SW2206 EVQ21505R STOP/EJECT SW2207 EVQ21505R C2201 R2201 3.9K R2203 1.8K R2204 1.2K REC/OTR R2206 820 CH.DOWN R2208 560 D2201 0.01 B MTZJ6.8B OS2201 RPM7138-WH10 Vout R4215 4.7K R4219 5.0 D4207 1SS133 0 0 ZERO_SW Q4204 DTC124EKA 1K 1 W838 C2205 100P CH CH.UP R2212 4.7K 1/4W R2211 4.7K 1/4W 10V 100 YK 100uH C8094_1 L8002
4.7K
2.2K
PLAY
FF
GND 2 B+ 3
P.CON+5V
JACK_OUT
P.CON+5V_E
KEY_B
FRONT_V_IN
AT+5V
SPDIF-134
REAR_V_IN
REMOCON_IN KEY_A
SOUND_R+
EXT_MUTE
JACK_OUT
SP_OUT_L
P.CON+8V
100 YK
R4212
4.7K
1SS133
NC
0.022 B
R4218
TP4201
W813
1K
220
16V
0.1
R4204
(W093)
L4205
5.2
100uH 0305
W4BRH3.5X6X1.0
8.1 25V 10 KA R4216 680 220 1/2W 8.8 MTZJ5.6B MUTE SW Q4210 2SA1037AK 470P B C2209 470P CH
25V
10 KA
470
150
1/2W
R4217
B2201
C4205_1
10K
C2206
16V 100 YK
C4208
FRONT_A_IN_R
FRONT_V_IN
FRONT_A_IN_L
470P
R4231
5.6K
100P CH
C4213
R2202
C4210
470P CH
16V 100 YK
470P CH
33P CH
C4203
C4202
C4214
W886
C4220
220 1/4W
470P
470P
H1 2
H2
H1
75
H2 H1 NC H1
2.5
R4238
2 1
2 1
C2202
2 1
C2203
470P CH
1.9
NC
NC
CH
NC
NC
NC
CH
5.6K
SOUND_GND GND
470P
R4203
75
0 0
CH
C4209
C2207
10 KA
330 1/4W
470
25V 10 KA
R4220
C4211
C2213
1/4W
R4209
R4207
R4239
C4204_1
C4212_1
CH
YELLOW
WHITE
RED
PCB010 VMC293
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
G-13
G-14
(VCR PCB)
8
COMB_FSC 100CT3R532 3.579545MHz R626
(W101)
W893
220 KA C627
0.047 B
R636
5.6K
C632
C624
C625
0.1 B
22K
X601
0.1 F
6.3V
C616
0.1 B
0.1 B
C631
C628 NC NC NC 0 0 0 4.9 NC 0 4.8 2.6 2.5 4.3 3.9 NC 2.6 NC3.6 NC 5.0 3.1 3.5 2.7 48 47 46 45 39 38 37 36 35 34 33 44 43 42 41 40 32 0.47 B 3.9 49 0 31 2.7 30 VXD 52 VIDEO SW AUDIO SW TINT APC1 FSC CLMP HOR VCO X-RAY 1/256 BUS TRAP 56 V/Y SW CL SHARP BS SG RGB MATRIX COLOP CLAMP SYNC SEP VER SEP VER C/D VER RAMP ABL/ACL HOR VCC HOR C/D FBP AFC1 AFC2 PHASE SHIFTER HOR OUT 29 2.5 0 28 AF SW 0 27 1.7 26 5.1 25 0 24 NC 1.5 58 23 OSD CONTRAST OSD SW ORIVE/OUT-OFF CLMP REG-SW RST 5V/8V-REG 2.6 22 5.2 21 2.4 20 3.1 62 19 3.1 63 18 C611 B 0 64 17 0.47 B 5.0 16V 100 KA 4.4 4.4 0.1 B C613 10K 9.0 W892 SW Q605 DTA114EKA R628 C612 R616 330 1/4W C618 R617 0.015 B C619 1B R627 2.2K R619 4.7K +-1% C622 1 B C601 0.01 B W827 R602 1K 1/4W R622 390 1/4W 33 DVD_Y/C-Y
6
1 2 3 4 5 6 7 8 9
FROM/TO DEFLECTION CP602 (CP602B) B2013H02-9P V.OUT TV_POWER_H AFC ACL NC H.OUT P.CON+5V EMERGENCY +B_DOWN OSD_G L604 W5T29X7.5X19 OSD_R 1K 1/4W R635 H.OUT P.CON+5V EMERGENCY OSD_Y OSD_B R630 1K V.OUT TV_POWER_H AFC ACL SDA SCL W810 W819
8P
DVD_Y/C-Y
4.7M
R620
R624
REG SW CLMP
53
51
50
55
54
BPF
YC SN
ACC
CEMO
40 AFC H.OUT 39
CD602 CU291701
H.SYNC V.SYNC TEST POINT CP601 A2001WR2-4P 1 2 3 4 GND SCL SDA IIC_OFF SCL SDA IIC_OFF TV_POWER_H VCR_POWER_H R623 3.3K 1/4W R632 4.7K 1/4W 5.0
61
H_CONTROL
MTZJ12B
C614
0 SW Q606 0 2SC2412K
1 0 FROM TV POWER
5 8.6
6 2.5
7 3.4
8 2.5 NC
9 4.3
10 8.5
11 2.6
12 7.8 NC
13 3.4 100
14 3.4 100
15 3.5 100
16
R609
R610
C604
R611
36
37 38 V.OUT
R608
D605
0.33
FROM/TO MICON PROTECT EMERGENCY 1K R612 V.SYNC H.SYNC VCR_POWER_H IIC_OFF OSD_Y R633 10K OSD_B OSD_G OSD_R SDA P.CON+5V_B R603 100 OUT 1 10.0 R634 1K 5.0 0 PROTECT Q602 0 2SC2412K 16V 100 KA 0 GND 2 12.0 IN 3 C607 B
4.7K
0.1
16V 100 KA
0.1 B C609
C606
R607
C603
27K
C608
C634 1 B
PCB010 VMC293
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE.
G-15
G-16
(VCR PCB)
+
1 6.6 2 3.5 3 0
4 3.5 5 3.9
L 6 1.3 7 0
10 3.5 11 0
+
12 3.5 R357
C328
50V 22 YK
HS351 763WAA0297
C302 0.0056 B FROM TV POWER S814Y R356 SOUND+B C321 25V 2200 YK SOUND_GND 100K 1/4W W843
R301
6
GND
8.2K
R307 50V 22 YK 8.2K 6.3 10K 1/4W R308 0 0 MUTE SW Q350 2SC2412K
18
C357
W881
CD303 C3149004
47K
1/4W
SDA SCL
C306_1
KA
25V 10 KA
0.015 B
R306
0.01 B C325
0.033 B
C316
C319
0.033 B
C329_1
1 PF1
1.9
4.6
3 L IN
7 PF3
4.2
AGC
PF2
8 PF4
NC 12 NC
NC 13 NC
2.3
14 BD
4.0
15
25V 10
C304
C308
KA
4.5
16
VD L ONT
R305 FROM DVD IN/OUT 2.7K R303 SW_AUDIO_OUT_L 2.2K SW_AUDIO_OUT_R R304 2.2K
AGC
SURR
Tone Control
+ + NC 21 0 NC NC 20 R OUT 19
Balance /MUTE
R311
10K 1/4W
C312
25V 10
0.33 B
C327_1
R IN 30 4.6
Vref 29 3.9
NC 28 0 NC
NC 27 0 NC 3.9
BB 26
RB 25 4.0
RT 24 4.2
BLD 23 3.4
TD 22 2.3 KA
SDA 18
SCL 17
0 NC 4.5
5.02
5.02
KANP
C305_1
C311_1
16V 10
25V 10
0.01 B C310
C307
16V 220 YK
50V 1 KA
100uH 0607
25V 10
C315
PCB010 VMC293
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
G-17
G-18
(VCR PCB)
P.CON+5V_A VCR_A_MUTE SDA SCL FSC
L5504
0.001 B
22uH 0305
C5563
C5564
0.1
6.3V
47 KA
50V 0.22
7
C5542 10 YK R5519 50V 10 YK
C5522_1
YK
C5528
33 KA
4.7
50V
KA
22K
C5540_1
C5523
R5514
50V
10V
C5544
4.7
27K
R5523 C5504 0.1 B 1M R5503 3.9M C5509 0.1 F C5513 0.1 C5506 0.1 B AUDIO_OUT_R 35V C5510 0.1 B C5514 22 YK C5512 R5522 1K 55 0 1.2 C5515 D5501 11EQS04TA1B2 L5501 100uH C5501 0.1 B C5502 16V 47 YK R5501 1.2K 1/4W R5502 330 C5503 0.047 B B 0.6 C5508 50V 10 YK C5517 0.1 B 4.3 NC 1.0 NC 2.4 2.3 2.2 35V 22 YK 4.3 11.0 B 51 4.9 22uH 0305 2.5 4.2 2.3 Hi-Fi/AUDIO/HEAD AMP/DEM IC IC5501 AN3663FBP
50V
2.2 48
0 4.9 41 40
0 NC 39
ZZ-PROM
0 1.6 38 37
6
0.015 B C5551 FROM DIGITAL COMB FILTER TUNER_AUDIO HIFI ENV. TP5501 NC V.REC_ST_H HIFI_ENV C5556 2.5 0 4.9 C5559 0.6 0 0.7 0 0 2.4 2.4 0.7 C5565 82P CH C5552 C5553 C5554 C5555_1 0.1 B 0.015 B 50V 10 YK 25V 10 KA FROM REGULATOR P.CON+5V_A P.CON+12V 6.3V 47 KA C5566 82P CH C5558 22uH 0305 C5549 0.1 F C5557 0.1 B L5503 P.CON+5V_A C5560 HF2 0.01 F 0.01 F HF1 HF_COM FSC Y/C_AUDIO NORMAL_A FROM/TO Y/C/AUDIO/HEAD AMP 0.01 B 20 HIFI_H.SW
50
31 30
S/N
2.7
49
3.4
52
53
MATRIX MUTE FROM 1PIN R SW18 BS L NORMAL SW19 R MUTE L HIFI MIX SW16 MIX HIFI BS FROM 3PIN
AMP
50V 2.2 YK
OUTPUT SW R L AMP
REC LPF HPF NOISE DET SW10 LINER SW HA1 HOLD TIMING
54
J
AN3672FBP
26
27
28
SW9
RCH VCO
29
SW21
SW NOISE
PB
REC
56
LCH BPF
57
58
59
HA2 +
60
SW22 L
61
DET AGC
62
SW11
63
64
VREF1
2 2.3 C5525_1
3 0 25V 10 KA
4 2.2
5 2.4
6 2.1
7 0.5
8 0
9 0
10 0
11 2.0
12 2.2
13 0
14 0
15 2.4
16
50V 10 KA
C5541
0.022
10V 33 KA
C5534
C5545_2
C5530
17
18
19
Y/C_AUDIO
SW15 H
20
NORMAL_A
21
22
AUDIO LIMIT
CURR AMP -
23
P.CON+12V
PC
PB LPF
24
AUDIO_OUT_L
SW17 R
25
ST_SELECT
RCH BPF FM UM
50V 3.3 YK
25V 10 KA
C5519
25V 10 KA
C5526_1
50V 10
C5535
50V 4.7 YK
KA
C5533
C5536
0.1 B
50V 4.7 KA
C5529
C5531
C5538
390 R5507
390
R5506
680P CH
680P CH
R5510
8.2K
C5543
50V 1 YK
R5518
C5521
C5527
8.2K
R5513
R5515
8.2K
8.2K
56K 1/4W
R5508
56K 1/4W
R5511
R5516
3.3K
R5509
3.3K
R5512
R5524
1/4W
56K
56K
FROM/TO TV POWER
W872
DVD_A_OUT_R
FRONT_A_IN_R
DVD_A_OUT_L
REAR_A_IN_R
REAR_A_IN_L
FRONT_A_IN_L
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
G-19
G-20
(VCR PCB)
C1511 27P CH C1506 0.1 B C1518 TO Hi-Fi/DEMODULATOR 6.3V C1505 0.01 B 0.01 B C1507 0.01 B C1509 470 YK TUNER_AUDIO W820 P.CON+5V
7
C1519 0.1 B
1 AVSS
2 VRB
2.4
3 VRT
3.0
4 ADIN
2.6
5 BIAS1
2.6
6 TEST
7 KILLER
8 DVDD
BIAS2
BIAS3
R1510
CKIN
AVDD
VFIL
DVSS
YOUT
COUT
100P CH
R1506
180P CH
820 C1515
1.9
5.4
3.8
1.4
4.2
3.6
2.2
2.5
5.4
16
15
14
13
12
11
10
27K
2.5
6
R1512 39P CH
R1507
C1513
R1511
C1523
24K
560
1K
R1501
180
5
L1501
L1504 150uH 220 YK C1516 16V R1502 6.8K 5.0 BUFFER Q1501 2SC2412K R1505 R1503 100 3.3K 56P CH L1502_1 15uH 47 KA 4.4 2.1 R1520 120 R1509 1K C1528 C1530 0.1 B
TUNER_VIDEO P.CON+8V_B
C1502 0.1 B
1.7 1.1
16V
C1501
AV SW IC IC1502 MM1501XNRE 4.4 Vin1 SW1 1 4.2 GND Vin2 V OUT Vcc 2 7.8
FROM/TO DEFLECTION
4.9 4 3
S814X 390 1/4W VIDEO OUT SW IC IC1505 MM1504XNRE 1.0 4.4 Vin1 SW1 6 1 B 0 GND Vin2 5 1.8 Vcc 4 3 6dB V OUT 2.1 2 R1519 MONITOR TUNER 17 VIDEO OUT 15 AT+30V
20
AV SW IC IC1504 MM1501XNRE 5.0 Vin1 SW1 GND Vin2 V OUT Vcc 2 7.3 12.5 16V 100 YK 0.1 B C1536 C1535
R1518 1K
AV_SW1 AV_SW2 L1506 100uH SDA SCL AFT FROM REGULATOR AT+30V P.CON+5V P.CON+12V P.CON+8V
C1534_1 25V 10 KA
10 CLOCK
11 DATA
C1538 +B 9 NC 8 NC 7 NC 6 NC 5 NC 4 NC 2 NC 1 NC 1
18
16 NC
3
21
8.0
P.CON+12V
0 NC 2.1
3.9
31.5
4.2
0 NC 4.8
1.4
NC
NC
NC
NC
W837
NC
NC
0 NC 0 NC
31
FRONT_V_IN
0.001 B
C006
W829
R1515 FROM/TO IN/OUT 1K 1K 1/4W REAR_V_IN C1537 FRONT_V_IN 50V 10 KA JACK_OUT C1520 B
W815
C001 0.1 F
2
W811 100uH L001 32 TUNER_AUDIO TUNER_VIDEO
R1516
P.CON+8V_B
W863
DVD_VIDEO
SDA
AFT
P.CON+5V
REAR_V_IN
JACK_OUT
AT+30V
SCL
AV_SW1
AUX_V[F/R]
Y/C_VIDEO
PCB010 VMC293
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
RECORD LUMINANCE SIGNAL RECORD COLOR SIGNAL PLAYBACK COLOR SIGNAL PLAYBACK LUMINANCE SIGNAL TUNER VIDEO SIGNAL
G H
G-21
G-22
(VCR PCB)
TO SOUND AMP/SURROUND SW_AUDIO_OUT_L AV_SW1 SW_AUDIO_OUT_R
7 8 9 10 11
0.1
16V
6
DVD_Y/C-C DVD_VIDEO C8009_1 AUDIO_OUT_R AUDIO SW IC IC8002 MM1501XNRE 6 1 7.8 Vin1 GND Vin2 SW1 V OUT Vcc 4.37 8.6 12.35 100 KA L8003 P.CON+12V 100uH 0305 TX RX DVD_RESET AV_SW1 25V 10 KA AV_SW1 SW_AUDIO_OUT_R FROM/TO MICON TO CHROMA/IF DVD_Y/C-Y
0 ZERO MUTE SW Q8007 DTC124EKA 0 ZERO MUTE SW 0.7 0.7 Q8006 2SC2412K 0
C8014
12 11 10 9 8 7 6 5 4 3 2 1
CVBS GND C(CVBS) GND Y GND AUDIO-L GND AUDIO-R ZERO DVD RESET (DVD_H) GND
16V
0.1
C8015
FROM/TO AUDIO/VIDEO
AT+5V
P.CON+5V_E S809X ZERO DVD_RESET S809Y FROM REGULATOR P.CON+3.8V P.CON+5V_D P.CON+12V P.CON+9V_DH DVD_A_OUT_L 16V 220 YK 50V 2.2 KA C8020 100P CH C8044 0.1 F C8090 C8002 0.1 B P.CON+12V R8022 10 1/4W C8070 R8051 C8081 12K 820P CH R8023 10K 1K R8027 R8049 10K 0 4 MIXER IC IC8004 NJM4580M(TE1) A_GND 6.1 3 6.1 2 + VCC + 5 820P CH R8047 1K 6 6.1 6.1 7 12.3 6.1 1 100P CH R8054 8.2K C8004 16V 22 KA R8056 3.9K FROM/TO Hi-Fi/DEMODULATOR W851 29 DVD_A_OUT_L DVD_A_OUT_R AUDIO_OUT_L AUDIO_OUT_R C8005 DVD_A_OUT_R TO Y/C/AUDIO/HEAD AMP DVD_VIDEO AT+5V
30 C8003 16V 22 KA
8 W850
2
C8064
C8065
R8050
820P CH
C8025
100P CH
C8102
50V 2.2
10K
10K C8079
8.2K
3.9K
KA
R8026
R8048
12K
R8052 R8053
PCB010 VMC293
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE.
NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
G-23
G-24
(VCR PCB)
8.0 AT+5V OUT Q3003 KTC3209_Y 5.7 5.0 D3004 R3001 100 1/4W SB140-EIC 25V 10 KA C3004_1 P.CON+5V_A OUT IC IC3003 KIA278R05PI IN 1 C3002_1 10V 100 YK C3001 7.5 5.0 OUT 2 GND 3 SW 4 5.0 D3005 11EQS04TA1B2 AT5.7VREG
8
P.CON+12V MOTOR+12V UNREG+8V UNREG+5V +B GND TO DIGITAL COMB FILTER P.CON+5V P.CON+12V BUFFER Q3015 2SC2412K 5.0 5.0 VCR_POWER_H P.CON+8V AT+30V 5.0 R3024 10 1K TO Y/C/AUDIO/HEAD AMP P.CON+5V_A P.CON+8V
5.6 6.3V
C3005 470 YK
21DQ09N
D3008
W809
6.3V 1000 YK
0.1 B C3009
R3010
12.0
7.8 P.CON+8V SW Q3002 KTC3209_Y R3006 100 1/4W 10V 470 YK C3022
P.CON+8V FROM/TO MICON VCR_POWER_H AT+12V P.CON+5V_C DVD_H P.CON+5V_D OUT IC IC3001 KIA278R05PI P.CON+9V_D OUT IC IC3002 KIA278R09PI AT+5V BACKUP+5V P.CON+5V_A
18 1W 8.5
8.5VREG
5
8.0
IN 1
OUT 2 5.0
GND 3 0 5.0
SW 4
IN 1 8.0
OUT 2 5.0
GND 3 0 5.0
SW 4
OUT 2
GND
R3009 R3008 21DQ09N 220 1/4W R3017 560 1/4W 6.3V 470 YK C3025
16V 470 YK
D3011
R3011
C3024
C3027
R3018
0.1 B
0.1
10
C3028
10
18
4
L3001
P.CON+5V FROM/TO CHROMA/IF P.CON+3.8V 10uHTSL0808 5.0 4.0 3.3 220 +-1% 3.3V OUT Q3005 KTB1366 C3012 5.0 3.3V CTL Q3004 2SC2412K 3.8 R3027_1 100 1/10W 5.0 5.0 MTZJ4.7B 6.3V 470 YK 2200 YK D3003 BUFFER Q3001 2SC2412K 5.0 C3013 8.5VREG AT5.7VREG R3007 50V 1 KA 15K DVD_H P.CON+8V P.CON+5V P.CON+5V_C
35V 22 YK
C3003
100P CH R3012
C3014
0.1 B C3023
+-1%
C3010
R3013
P.CON+5V
1.5K
6.3V
C3008
HS3001 763WAAA077
5.0
MTZJ33B
50V 1 KA
D3001
MTZJ5.6B
50V 1 KA
C3007
C3016
D3002
C3011
+B
SW Q3011 2SC2412K
0 0
TO DVD IN/OUT R3016 10K VCR_POWER_H AT+5V P.CON+12V P.CON+3.8V P.CON+5V_D P.CON+5V_C P.CON+9V_DH
R3005 16V 220 YK R3004 10K 1/4W 0 12.0 12.0 R3021 22 1W 4.7K C3006 R3020 100 1/4W 10.0 P.CON+5V_C SW 5.6 Q3010 KTC3209_Y 5.0
5.0
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
G-25
G-26
(VCR PCB)
FROM/TO MICON POWER_FAIL DEGAUSS_H D1719 D1702 1SS133 10.9 RELAY DRIVE Q1702 KTC3198 R1705 0 SB340L-6737 R1708 10K 10K C1729_1 (S811) RY1701 2 ALKS321 3 DEGAUSS COIL L1703 8R200024 1 2 1 CP1704 A1561WV2-2PK 1 1/2W 2.7M +-10% 2KV 560P RR TO CHROMA/IF 4 R1702 B1703 35V 1000 MHE 1K MTZJ12B 1/4W R1726 D1732 W4BRH3.5X6X1.0 C1717 MOTOR_GND GND TO SOUND AMP/SURROUND SOUND+B SOUND_GND GND
TH1701 ZPB45BL3R0A
CP1707 003P-2100
CP1708 003P-2100
R1718 2KV 560P R RM11C-EIC W831 1 1.2 7W RM11C-EIC 2.2M 1/2W D1710 R1722 C1705
6
SOUND_GND GND FROM/TO Hi-Fi/DEMODULATOR GND FROM/TO DIGITAL COMB FILTER
D1705
ECQUL
1.5M 1/2W
AC120V_60Hz CD1702 09415910 BLADE WIDE R1701 CD1703 WHITE BLACK CD1704 BLACK
C1701
RM11C-EIC
RM11C-EIC
D1706
D1711
MTZJ18B
D1717
5
L1704 W5T_20X10X10A
FH1701 EYF-52BCY
FH1702 EYF-52BCY
8.0 NC 0
W888
2KV 0.0022 B
2KV 0.0022 B
C1714
WHITE
275V 0.22
C1708
C1710
10 16.0 8 11 10.0
160V
5
D1713 +B UNREG+5V 10V 2200 YK 21DQ09N C1728_1 D1734 21DQ09N MOTOR+12V UNREG+8V P.CON+12V GND FROM/TO DVD IN/OUT 25V 1000 YK
6.3A 125V
115 0 0 12.0
W898
R1720 0.22 1W
168 168
2KV 820P RR
C1707_1
165.8 D S 0.2
HS1701 763WAA0238 R1717 330 2W C1713_1 100V 0.047 MMTS 500V 0.001 B
C1732
FE201-6L49
TO DEFLECTION (CP604) CP1702 B2013H02-8P +B 1 2 3 4 5 6 7 8 CD604 C3282402 +B NC NC GND GND GND P.CON+12V H VOLT
1SS133 R1714 16.3 4 R1707 C1702 0.01 B D1703 MTZJ2.7B FEED BACK SWITCHING IC IC1702 KIA431A-AT 3.9K 10.7 100 1/4W FEED BACK IC1701 PS2561AL1-1-V(W) 1 9.7 2 C1722 B 1.5 3 0.15 1W R1715 150 R1731 390 1/4W
C1712
D1709
0.0027 B C1724
10.3
D1716 D1715 MTZJ18B 1/4W 1N4937 R1724 100 1/4W 25V 10 KA C1715 D1718 1N4937
D1722 1N4937
R1727 1K 1/4W
R1712
3.3K
R1709
0.022
0.0056 B
R1716
GND1
4.7K
R1713
W848
REFERENCE
330
CATHOOLE
R1719
56K 1/4W
100
50V
C1703
C1716
R1721
10K
R1710
D1728
1SS133
ANODE
1/4W
2.7K
D1727
1SS133
D1726
CAUTION:
VR1701 10K METAL
+B ADJ
1SS133
D1724
1SS133
2.5
4.0
C1711
250V 0.0047 KX
MTZJ6.8B
D1721
D1720
1SS133
R1706
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE.
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
G-27
G-28
(DEFLECTION PCB)
V.OUTPUT IC IC401 LA78040 + PUMP UP VCC GND 2 3 4 4.0 25.0 2.0 0 THERMAL PROTECTION AMP
5 12.0
6 25.0
7 4.0 R418 10V 100 YK 2.2K 1/4W FROM/TO DY C438_2 CP404 A1561WV2-A5P 5 W821 22 560 1/2W R449 560 1/2W 100V 0.33 MKT 2.2K METAL VR404 NC 4 3 2 1 FB401_1 2.8 13.1 1.2K 1/2W R453 1.2K 1/2W 108.0 105.0 0 1 6 2 9 10 8 COL E180 B+ AFC HEA TER GND E12 E27 GND E8 F S 0 GND 11 ABL 8.1 7 C412 1K 1W C449 2KV 0.001 R L403_1 250V 2.2 MHE 4.7mH FJN20A003_M HV L402 ELH5L4113 R454 V801 A51QDJ420X58
7
R413 8.2K 1/4W C423 0.022 B C414 19
11E1-EIC C427
35V 100 YK
35V 100 YK
1.5K 1/4W
21
R444
R432 MTZJ30B 2200 MHE 39K 1/4W C430 MTZJ6.8B D413 D417 TO DVD DECK
560 1/2W
MTZJ33B
C429
C432
D418
R443
R421_1
C421
560 1/2W
R447
R415
F R437
10K
25V
6
9 10 8 6 11 R G B 5 7 1
CD807 CH012801
R429
HS402 763WAAA075
R439
TO VCR DECK
TO CRT
CD805(CP805) CH823004
5
FROM TV POWER (CP1702) CP604 A2001WV2-8P 1 2 3 4 5 6 7 8 +B +B NC GND GND GND NC H.VOLT R423 FROM/TO CHROMA/IF 0.56 CP602B (CP602) A2001WV2-9P 1 2 3 4 5 6 7 8 H.OUT P.CON+5V EMERGENCY +B_DOWN 2 TP401 3 1 114.0 0 4 3.3K SW Q408 KTC3207 0 CP001 003P-2100 1 C406_1 50V GND 2.2 KANP D416 1N4005-EIC R440 10W C V.OUT TV_POWER_H AFC ACL AFC ACL NC H.OUT P.CON+5V 1SS133 D408 MTZJ5.6B W830 V.OUT 2W GND NC +B 115.0 CURRENT DET. Q406 0 2SA1624 W852
C415 NC 0.001 B
23 B401 W5RH3.5X5X1.0 T401_1 24 ETH14Y47AY 100 1/4W 0.01 MMTS 5 1 C405_1 R414 NC 4 0.1 2.8
W5RH3.5X5X1.0 C418_1
0 8 NC 5 0.1
C402
B403
R412_1
115.0 C426 H.DRIVE Q401 KTC3227_Y 17.3 0.4 0 470 1/2W C407 R407
W5RH3.5X5X1.0
B402
1/4W
2.2K
47K 1/4W
R431
100V
R425
HS401 763WAAA031
W822
100V 2.2 YK
R427 R419
50V 22 MHE
D404 1SS133
33 1W
C408_1
R406 180 2W
2 C404 47 BXA
R442
D402 AU02A-EIC
500V 0.0022
R401
100V 22 YK
NC
(CD002)
W807
C403
2.7
PCB080 TMC564
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
G-29
G-30
TP802
R814 15K 2W 41
CRT BLOCK
R822 2.7K 1/4W
R805
RED AMP Q802 2SC4217 7.8 D802 1SS133 7.3 W832 3.0
123.5 7.3
220 1/4W
RED AMP Q803 KTC3199_Y 2.4 56 1/4W R815 15K 2W 42 R821 2.7K 1/4W 123.9 0 7.3 117.0 0 GREEN AMP Q805 KTC3199_Y 2.4 C801 56 1/4W 7 6 5 4 0 0 8 121.0 0 9 10 11 12 6.2 119.0
FROM CROMA/IF CP603B (CP603) A2001WV2-8P 1 2 3 4 5 6 7 8 CUT OFF GND R.OUT G.OUT B.OUT CLAMP_OFF NC NC R810 W831
220 1/4W
C815
680P CH
R824
GREEN AMP Q804 2SC4217 7.8 D801 1SS133 7.3 W833 3.0
220 1/4W
NC
F
CRT SOCKET J801 ISHS62S
100P CH
C817
560P CH R816
L804
15K 2W 100uH 0607 43 BLUE AMP Q806 2SC4217 7.8 119.7 R820 2KV 0.001 B 250V 1 YK 2.7K 1/4W C819
220 1/4W
7.3
4
D803 1SS133 W834 CC801 8990TPA002 FROM DEFLECTION CP802B (CP802A) HEATER GND NC 180V NC 180V FROM/TO DEFLECTION R808 R819 1.8K 1/4W D804 1SS133 3.1 7.3 2.5 220 1/4W BLUE AMP Q807 KTC3199_Y 560P CH
C820
R809
56 1/4W
C816
W806
R826
ACCESSORY
4 3 2 1
FOCUS
PCB110 TCC426
(OPERATION PCB)
2 2
EVQ21505R
EVQ21505R
OPEN/CLOSE SW2251
EVQ21505R
EVQ21505R
EVQ21505R
EVQ21505R
EVQ21505R
EVQ21505R
VOL UP SW2253
SKIP SW2254
STOP SW2255
PLAY SW2256
SKIP SW2257
POWER SW2258
S801
SCREEN
GND
GND GND
GND
R2255 1K 1/4W
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
PCB270 TECB10
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
G-31
G-32
A
CD2001 TT+ FF+ DVD DRIVE DM-3 MON(DVD) NC(SW) VOL(DVD) GND(DVD) LD(DVD) LD(CD) VOL(CD) GND(CD) MON(COM) DVD/CD 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 FFC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 CP2301 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 TT+ FF+ MON(DVD) NC(SW) VOL(DVD) GND(DVD) LD(DVD) LD(CD) VOL(CD) GND(CD) MON(COM) DVD/CD RF C B A D F E VCC Vref GND(PDIC)
B
L4002 GND GND TX RX GND(M) P.CON+9V P.CON+5V P.CON+3.8V P.CON+3.8V GND SPDIF-134 CD4002 1 2 3 4 5 6 7 8 9 10 11 FFC 1 2 3 4 5 6 7 8 9 10 11 12 12 11 10 9 8 7 6 5 4 3 2 1 1 2 3 4 5 6 7 8 9 10 11
C
CP8001 GND GND TX RX GND(M) P.CON+9V P.CON+D5V P.CON+3.8V P.CON+3.8V GND SPDIF-134
INTERCONNECTION DIAGRAM
8
CP8101_2 CVBS GND C(CVBS) GND Y GND AUDIO-L GND AUDIO-R ZERO DVD RESET GND 1 2 3 4 5 6 7 8 9 10 11 12
CP8002 12 11 10 9 8 7 6 5 4 3 2 1 CVBS GND C(CVBS) Y SPEAKER GND OPERATION PCB PCB270 TECB10 AUDIO-L KEY-B GND GND AUDIO-R ZERO DVD RESET GND CD2251 SP351 8 OHM SP352 8 OHM GND COMMAND TRANSMITTER TM101 FULL ERASE HEAD ASSY H5002
7
HALL SENSOR MAIN COIL ROTOR MAGNET MR FG SENSOR VCC
SPEAKER
FE HEAD (GND)
FE HEAD (HOT)
CD303
CP2302 CP601 CP303 1 2 1 2 3 4 4 3 2 1 1 2 3 4 5 1 2 3 4 5 CP2303 CLOSE GND(D) GND OPEN CP2201 LD+ LDKEY-B
OS2201 CP4503 1 Vout 1 2 CP101 1 2 3 4 5 6 7 8 9 10 11 12 CAP FG CAP VCO VCC CAP.M F/R I LIMIT MOTOR GND GND LD/CY VCO CAP CTL LDM CTL CYL FG/PG CYL CTL 1 2 3 4 5 6 7 8 9 10 11 12
IIC_OFF
GND
4 5
1 2 3 4 5 6
SDA
SCL
OPEN
SOUND L+
SOUND R+
CLOSE GND(D)
1 2
SOUND L-
SOUND R-
GND 2 B+ 3
5
1 2 3 4 5 6 7 RED WHITE LM LOADING MOTOR M101 1 2 3 4 5 5 D-W OUT 6 6 D-V OUT 7 D-U OUT 7
CP001 GND 1 CP602B V.OUT TV_POWER_H AFC ACL H.OUT P.CON+5V EMERGENCY TV MT PCB PCB080 TMC564 +B_DOWN 1 2 3 4 5 6 7 8 9 CD604 FFC CD602 FFC
CD002 1 CP602 1 2 3 4 5 6 7 8 9 H.OUT P.CON+5V EMERGENCY +B_DOWN CP1702 1 2 3 4 5 6 7 8 +B +B NC GND GND GND P.CON+12V H VOLT 12 AFT OUT 13 AUDIO OUT VCR MT PCB PCB010 VMC293 MONITOR TUNER TU001
21 20
GND L604 V.OUT D-PG GND D-PG OUT M-GND TV_POWER_H AFC ACL D-COM 1 2 3 4
FFC
UN4001 CYLINDER UNIT ASSY CP4501 HF1_(R) HF_COM HF2 (L) SP-CH1 (R) SP_COM SP-CH2 (L) EP/LP-CH1 (R) EP/LP_COM EP/LP-CH2 (L) 9 8 7 6 5 4 3 2 1 9 8 7 6 5 4 3 2 1 FFC 9 8 7 6 5 4 3 2 1 EP/LP HEAD SP HEAD HI-FI HEAD
17
VIDEO OUT
CP802A
180V
GND
FBT FB401_1
CD603 FFC
NC
FOCUS SCREEN
11 DATA 10 CLOCK 9 NC 8 NC 7 NC CP4502 AUDIO REC AUDIO PB CTL+ 6 NC CTLAE HEAD(+) AE HEAD(-) 6 5 4 3 2 1 6 5 4 3 2 1 FFC 6 5 4 3 2 1 6 5 4 3 2 1 AUDIO REC AUDIO PB CTL+ CTLAE HEAD(+) AE HEAD(-) AE CONTROL AUDIO HEAD AUDIO CONTROL ASSY H5001
ANODE
4 5 6 7
S801 SCREEN
CP802B
FOCUS
11
2
10 9
CP603B CUT_OFF GND 1 R.OUT G.OUT B.OUT CLAMP_OFF 1 BLADE WIDE 2 3 4 5 6 7 8 L1704 1 2 F
5 NC 4 NC
WHITE BLACK
COAXIAL J8007
3 +B 2 NC 1 NC
18 19
CD4501
1 2
1 3 2
CD1704 BLACK
GND
GND
GND
GND
AC120V_60Hz CD1702
NC
NC
NC
H1 NC H1 H2
CD1705
CP805
CP803
TO DVD DECK
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
ATTENTION
:LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
1
NOTE: THIS INTERCONNECTION DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
CD805
CD803
G-33
G-34
WAVEFORMS
MPEG/MICON/DSP
10ns 100mV
AUDIO/VIDEO
500s 500mV
Y/C/AUDIO/HEAD AMP
20s 1.0V
11
5ns 20mV
500s 500mV
2s 1.0V
12
20ns 1.0V
10s 100mV
1ms 1.0V
13
200ns 1.0V
100s 200mV
5ms 2.0V
14
MEMORY
5ns 500mV 10s 200mV 20s 20V
10
15
NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
H-1
WAVEFORMS
MICON
20ms 2.0V
DEFLECTION
10ms 10V
DEFLECTION
20s 200V
16
21
26
MICON
1ms 2.0V 10ms 10V 50s 2.0V
17
22
27
SOUND AMP/SURROUND
1ms 200mV 50s 10V 10ms 2.0V
18
23
28
DEFLECTION
10ms 0.5V 50s 5.0V
DVD IN/OUT
1ms 2.0V
19
24
29
Hi-Fi/DEMODULATOR
1ms 1.0V
CHROMA/IF
20s 0.5V 1ms 2.0V
20
25
30
NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
H-2
WAVEFORMS
DIGITAL COMB FILTER
20s 0.5V 20s 1.0V
CRT/OPERATION
20s 50V
31
36
41
0.5ms 0.5V
20s 1.0V
20s 50V
32
37
42
CHROMA/IF
20s 0.5V 10ms 1.0V 20s 50V
33
38
43
0.5s 100mV
50s 0.5V
34
39
20s 1.0V
50s 2.0V
35
40
NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
H-3
111
118
202
202
102B
202
208
131
102 113 201
102A
202
102B
201
131
131
131 201
SP351
101K 212 212 212 101K
SP352
101C
101I
101D
212
212 133
101K 101G
212
212
101H
212
101K 101G
101A
101
135
I1-1
123
208 208
204 115
209 114
214
214
213 213
213
208
110
205
121
116
130
117
208 211
208 126 208
128
132
127
203
122
I1-2
503
UN4001
334
333 501 H5002 314 336 324 315 323 503 335 342
504
H5001
317
341
306
331 508 322 508 312 305 302 301 AA 313 AA 332 AB AB AB CD1502 AA AA
AD
AC AB 307 AC
AB
506
345 346
507
318 AB
321
AB
510
AE AE
AB
CLASS GREASE
PART NO.
Y315061000 Y315071000 Y31D011000 Y315041000 Y315141000
PART NAME
MARK AA AB AC AD AE
I2-1
NOTE: Applying positions AA, AB, AC, AD and AE for the grease are displayed for this section. Check if the correct grease is applied for each position.
M2001
320
300
502
CD1502 338 AA 337 AA 509 308 344 327 343 326 328
AA AD 502 502 AA
AA 339 AA
AA
AA
AB
340
AA
AB
AB
AA
505 330
CLASS GREASE
PART NO.
Y315061000 Y315071000 Y31D011000 Y315041000 Y315141000
PART NAME
MARK AA AB AC AD AE
NOTE: Applying positions AA, AB, AC, AD and AE for the grease are displayed for this section. Check if the correct grease is applied for each position.
I2-2
611
600
612
Cannot supply separately. If the repair is needed, replace the LOADER SUB ASS'Y.
607
AB
SW1
CD2301
705
702
703 606 Do not replace the parts. Because, minute adjustments are needed if this condition is disassembled further more. If the repair is needed, replace the DVD MECHA ASS'Y.
605
CLASS GREASE
PART NO.
Y315061000
PART NAME
G-555G
SF-112
MARK AA AB
Y315121000
NOTE: Applying positions AA and AB for the grease are displayed for this section. Check if the correct grease is applied for each position.
I3-1
DESCRIPTION
FRONT,CABI ASS'Y CABINET,FRONT FLAP,DVD FLAT,FLAP GLASS,LED HOLDER FLAP STOPPER,BUTTON BUTTON,FRAME 1 BUTTON,FRAME 2 SPRING,FLAP SPRING,FLAP-DVD FELT,SHEET SHEET,DVD(NEW)
DESCRIPTION
SCREW,TAP TITE(P) SCREW,TAP TITE(B0) SCREW,TAP TITE(B0) SCREW,TAP TITE(B)R SCREW,TAP TITE(B) SCREW,TAP TITE(S) SCREW,TAP TITE(B) SCREW,TAP TITE(B) SCREW,TAP TITE(P) SCREW,TAP TITE(S) SCREW,TAP TITE(S) SCREW,TAP TITE(P) SEMS(F) SCREW,TAP TITE(S) FILM,BAG PACKAGE,TOP PACKAGE,BOTTOM LIGHTLON SHEET GIFT BOX PAD WARRANTY SHEET INSTRUCTION BOOK(E) INSTRUCTION BOOK(S) POLYBAG,INSTRUCTION INSTRUCTION BOOK KIT GW22 TRUSS TRUSS PAN WH7 BRAZIER BRAZIER BIND BIND BRAZIER BIND BRAZIER BIND 5x35 4x16 4x8 3x29 3x10 3x18 3x8 3x8 2.6x8 3x8 3x4 3x8 3x8 3x6
5x150xT=0.3
7A702A050A BACK,CABI ASS'Y 702WPAA747 CABINET,BACK 800WQ0A092 FELT,SHEET 701WPA0686 701WPA0751 752WSA0230 752WSA0290 752WSA0308 753WUAA006 755WPA0035 85OP700038 726000A083 761WPA0223 741WUA0021 753WUA0069 755WPAA012 761WSAA023 7230007691 722A08A163 762WPA0011 752WSAA122 752WSA0292 752WSAA075 752WSA0489 752WSAA080 752WSA0327 8995034000 774WPA0005 899HV3T000 7250000596 744WUA0013 769WSAA012 899EFBA002 752WSAA083 723000C727 7230007882 HOLDER,DECK HOLDER,DECK SHIELD,CASE HEAD AMP SHIELD,COMPO SHIELD,COVER HEAD AMP SPRING,EARTH HEAD AMP COVER,PCB HOLDER,END SENSOR SHEET,CRT SERVICEMAN HOLDER,FBT SPRING,EARTH SPRING,EARTH PLATE,COVER LIGHT (L) ANGLE,DECK SHEET,JACK SHEET,RATING HOLDER,CRT WIRE SHIELD,COVER DECK SHIELD,AV JACK PLATE,BOTTOM DVD,TOP VCR,TOP SHIELD,COVER FPC CORD CLIP UL CO. HOLDER,WIRE-2 HOLDER,ANODE WIRE SHEET,PC SPRING,EARTH WASHER CRT T=0.5 WIRING-CLIP ANGLE,FRONT SHEET,CAUTION SHEET,DTS(S)
9x390xT=0.5
J1-1
DESCRIPTION
A5T8016420A or
DESCRIPTION
SCREW,TAP TITE(S) BIND E-RING SCREW,TAP TITE(S) BIND SCREW,PAN SCREW,TAP TITE(B) PAN SCREW/WASHER(A) SCREW/WASHER(A) POLYSLIDER WASHER POLYSLIDER WASHER(CUT) SCREW,TAP TITE(S) BIND CORD JUMPER CORD JUMPER HEAD (AUDIO CONTROL) HEAD (FULL ERASE) MOTOR,LOADING CAPSTAN DD UNIT MICRO MOTOR CYLINDER UNIT ASS'Y M2.6x8 3 M2.6x4 M2x6 M2.6x6 M3x4 M2.6x5 2.6x4.7xT0.13 1.8x4.5xT0.5 2.6x6 2H071704 2Y021002 VTR-1X2RPE22-756 VTR-1X2ERS11-154 MDB2B66B F2QVB73B I20AL34K A5T8016500
! ! ! !
J2-1
DESCRIPTION
DVD MECHA ASS'Y HOLDER,TRAVERSE CLAMPER GEAR,MOTOR GEAR,MIDDLE INSULATOR(F) INSULATOR(R) LOADER SUB ASS'Y GEAR,PULLEY PULLEY,MOTOR GEAR,MAIN BELT,LOADING PLATE,CLAMPER RACK,LOADING FRAME,MAIN TRAY CUSHION C SHEET,FFC SCREW,TAP TITE(P) BIND SCREW,PAN SEMS.TAP TITE(P)PAN SCREW,PAN SCREW,TAP TITE(P) BIND CORD JUMPER CORD JUMPER CORD JUMPER FEED MOTOR MOTOR,LOADING PCB ASS'Y PCB ASS'Y SWITCH PUSH SWITCH 2.6x8 M1.7x2.3 P3 W10 2x8 M1.7x3 P3 2x8 2H0O1901 2H062102 2H052601 BCZ3B03B BCZ3B52B DED003A DED012B SSS-13-2 ESE22MH24 A2F401H650
J3-1
DESCRIPTION RESISTORS
R,METAL R,METAL R,METAL R,METAL R,FUSE R,METAL R,METAL OXIDE RC R,CEMENT R,CEMENT R,METAL OXIDE RC R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE RC RC RC R,METAL OXIDE R,METAL OXIDE R,CEMENT R,CEMENT R,FUSE R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE 5.6K OHM 1/6W 15K OHM 1/6W 15K OHM 1/6W 180 OHM 2W 33 OHM 1W 180 OHM 2W 0.56 OHM 2W 1 OHM 1/2W 0 2.7 OHM 10W 0 3.3K OHM 10W 2.7 OHM 3W 560 OHM 1/2W 1K OHM 1W 15K OHM 2W 15K OHM 2W 15K OHM 2W 1.5M OHM 1/2W 2.7M OHM 1/2W 2.7K OHM 1/4W 0.15 OHM 1W 330 OHM 2W 1.2 OHM 7W 1.2 OHM 7W 0.22 OHM 1W 18 OHM 1W 22 OHM 1W 4.7 OHM 1W 1000 UF 6.3V 2200 UF 25V 22 UF 100V 47 UF 160V 0.0056UF 1.25KV 0.47 UF 250V PMS 0.0068UF 1.25KV PHE 100 UF 35V 2200 UF 25V 1000 UF 35V 22 UF 250V 0.001 UF 2KV R 100 PF 50V CH 0.001 UF 2KV B 0.22 UF 275V ECQUL 560 PF 2KV R 820 PF 2KV RR 0.0022UF 2KV B 0.0022UF 2KV B 0.0047UF 250V 5 680 UF 200V 2200 UF 25V 1000 UF 35V 220 UF 160V 2200 UF 10V 560 PF 2KV R 1000 UF 25V 4.7 UF 50V
DESCRIPTION DIODES
DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE SILICON DIODE SILICON DIODE SILICON DIODE SILICON DIODE,SILICON DIODE SILICON DIODE SILICON DIODE,ZENER DIODE SCHOTTKY DIODE,ZENER DIODE SILICON DIODE,ZENER DIODE SILICON DIODE SCHOTTKY DIODE,SILICON DIODE,SILICON DIODE SILICON DIODE SILICON DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE SILICON DIODE,ZENER DIODE,SILICON DIODE SCHOTTKY DIODE,ZENER LED LED LED DIODE SILICON DIODE SILICON DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE SCHOTTKY DIODE,SCHOTTKY DIODE SILICON DIODE SCHOTTKY DIODE SCHOTTKY DIODE SILICON DIODE SILICON DIODE SILICON DIODE SILICON DIODE SILICON DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SCHOTTKY DIODE,SILICON DIODE SILICON DIODE SILICON DIODE SILICON MTZJ12B T-77 MTZJ12B T-77 MTZJ12B T-77 MTZJ12B T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 MTZJ2.7B T-77 RGP15J-G23 RM11C-EIC RM11C-EIC RGP15J-G23 1SS133T-77 RM11C-EIC RM11C-EIC MTZJ2.2B T-77 21DQ09N-TA2B1 MTZJ18B T-77 1N4937 MTZJ18B T-77 1N4937 SB340L-6737 1SS133T-77 1SS133T-77 1N4937 FE201-6L49 1SS133T-77 1SS133T-77 MTZJ6.8B T-77 1SS133T-77 FE201-6L49 MTZJ12B T-77 1SS133T-77 21DQ09N-TA2B1 MTZJ6.8B T-77 LTL-1CHEE-002A LTL-1CHEE-002A LTL-1CHEE-002A 1SS355 TE-17 1SS355 TE-17 MTZJ33B T-77 MTZJ5.6B T-77 MTZJ4.7B T-77 SB140-EIC 11EQS04TA1B2 11E1-EIC 21DQ09N-TA2B1 21DQ09N-TA2B1 1SS355 TE-17 1SS355 TE-17 1SS355 TE-17 1SS355 TE-17 1SS355 TE-17 MTZJ5.6B T-77 1SS133T-77 1SS133T-77 1SS133T-77 11EQS04TA1B2 1SS133T-77 1SS355 TE-17 1SS355 TE-17 1SS355 TE-17 OEC8078A XC61CN3102SR BR24L04F-WE2 AN5891SA-E1V AN7522N LA78040 LA76319NM-MPB-E KIA78L10F-RTF TC90A45FG MM1501XNRE
! ! ! ! ! ! ! or
! R1720 ! R3010 ! R3021 R3022 C005 C321 C403 C404 C408 C412 C418 C429 C430 C434 C446 C449 C801 C820 C1701 C1705 C1707 C1708 C1710 C1711 C1714 C1716 C1717 C1720 C1728 C1729 C1732 C1733 D101 D102 D103 D105 D106 D108 D402 D403 D404 D408 D410 D411 D412 D413 D414 D415 D416 D417 D418 D419
! !
CAPACITORS
CE CE CE CE CMPP CMPP CMPP CE CE CE CE CC CC CC CMP CC CC CC CC CC CE CE CE CE CE CC CE CE ! !
! ! ! ! ! ! !
! ! ! ! ! ! ! ! ! !
D I O D ES
INFRARED LED DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE SILICON DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE SILICON DIODE,ZENER DIODE SILICON DIODE,ZENER DIODE,ZENER DIODE SILICON DIODE SILICON DIODE,ZENER DIODE,ZENER DIODE,SILICON LTE-3271T-012A-O 1SS133T-77 MTZJ5.6B T-77 1SS133T-77 MTZJ15B T-77 1SS133T-77 AU02A-EIC 1SS133T-77 1SS133T-77 MTZJ5.6B T-77 11E1-EIC MTZJ5.6B T-77 AU02A-EIC MTZJ30B T-77 MTZJ30B T-77 AU02A-EIC 1N4005-EIC MTZJ6.8B T-77 MTZJ33B T-77 1SS133T-77
! ! !
ICS
IC101 IC103 IC199 IC302 ! IC352 ! IC401 IC601 IC602 IC1501 IC1502 IC IC INIT DATA IC IC IC IC IC IC IC
J4-1
DESCRIPTION
DESCRIPTION TRANSISTORS
TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON COMPOUND TRANSISTOR TRANSISTOR SILICON COMPOUND TRANSISTOR TRANSISTOR,SILICON TRANSISTOR SILICON TRANSISTOR,SILICON TRANSISTOR SILICON TRANSISTOR SILICON COMPOUND TRANSISTOR TRANSISTOR, SILICON TRANSISTOR,SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR SILICON TRANSISTOR SILICON COMPOUND TRANSISTOR COMPOUND TRANSISTOR COIL COIL COIL,LINEARITY COIL COIL COIL CORE,FERRITE CORE,FERRITE COIL COIL COIL COIL COIL COIL COIL,LINE FILTER COIL,DEGAUSS CORE FERRITE COIL COIL CORE,FERRITE COIL COIL,BIAS OSC COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL TRANS,HORIZONTAL DRIVE TRANSFORMER,SWITCHING KTC3209_Y-AT 2SC2412KT146 R,S KTC3209_Y-AT 2SC2412KT146 R,S KTC3875S_Y_RTK 2SC2412KT146 R,S DTA124EKAT146 2SC2412KT146 R,S DTC124EKAT146 2SA1037AKT146R,S 2SC2412KT146 R,S 2SA1037AKT146R,S KTC3875S_Y_RTK KTC3875S_Y_RTK DTA124EKAT146 KTC3203_Y-AT KTA1266-AT(Y,GR) 2SC2412KT146 R,S 2SC2412KT146 R,S 2SA1037AKT146R,S 2SA1037AKT146R,S 2SC2412KT146 R,S 2SC2412KT146 R,S DTC124EKAT146 DTC124EKAT146 100 UH 100 UH ELH5L4113 4.7 MH 100 UH 100 UH W5T29X7.5X19 W5T29X7.5X19 100 UH 10 UH 15 UH 150 UH 100 UH 100 UH SS28V-R20130 8R200024 W5T_20X10X10A 10 UH 2.2 UH W5T29X7.5X19 100 UH 1626009 100 UH 47 UH 47 UH 100 UH 100 UH 22 UH 22 UH 22 UH 100 UH 100 UH 100 UH 1 UH 1 UH 1 UH ETH14Y47AY 8142065S ISHS62S MSJ-2000_AG MTJ-032-05A-30-FE MTJ-032-05A-32-FE MTJ-032-05A-31-FE MSP-213V2-432_NI_LF MSP-213V1-432_NI_LF MSP-251V-05NI-FE-LF LSA-1144EAU EVQ21505R EVQ21505R
! !
! ! ! !
K4S161622H-UC60 or HY57V161610ETP-7 K4S161622H-UC60 or HY57V161610ETP-7 LA71205M-MPB AN3663FBP MM1501XNRE MM1501XNRE NJM4580M(TE1) PCM1753DBQR ST-304L DTC124EKAT146 ST-304L RPI-352C40N RPI-352C40N DTC124EKAT146 RPI-303 RPI-303 DTC114EKAT146 2SC2412KT146 R,S 2SA1037AKT146R,S 2SC2412KT146 R,S 2SC2412KT146 R,S KTC3227_Y-AT 2SD2499(LB0EC1) 2SA1624-AA KRC102MAT KTC3207-AT 2SA1624-AA DTC114EKT147 2SC2412KT146 R,S DTA114EKAT146 2SC2412KT146 R,S 2SC4217(D,E)-RAC KTC3199_Y-AT 2SC4217(D,E)-RAC KTC3199_Y-AT 2SC4217(D,E)-RAC KTC3199_Y-AT 2SC2412KT146 R,S KTC3875S_Y_RTK KTC3875S_Y_RTK KTC3198-AT(Y,GR) 2SK3326(2) KTC3203_Y-AT DTC114EKAT146 DTC114EKAT146 DTC114EKAT146 2SA1036KT146 2SA2048TL KTC3875S_Y_RTK KTC3875S_Y_RTK KTC3875S_Y_RTK 2SC2412KT146 R,S KTC3209_Y-AT KTC3209_Y-AT 2SC2412KT146 R,S KTB1366(O,Y) 2SC2412KT146 R,S KTA1281_Y DTA143EKAT146 DTC114EKAT146
TRANSISTORS
PHOTO TRANSISTOR COMPOUND TRANSISTOR PHOTO TRANSISTOR PHOTO COUPLER PHOTO COUPLER COMPOUND TRANSISTOR PHOTO COUPLER PHOTO COUPLER COMPOUND TRANSISTOR TRANSISTOR SILICON TRANSISTOR,SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR,SILICON COMPOUND TRANSISTOR TRANSISTOR SILICON TRANSISTOR,SILICON COMPOUND TRANSISTOR TRANSISTOR SILICON COMPOUND TRANSISTOR TRANSISTOR SILICON TRANSISTOR,SILICON TRANSISTOR SILICON TRANSISTOR,SILICON TRANSISTOR SILICON TRANSISTOR,SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR,SILICON FET TRANSISTOR, SILICON COMPOUND TRANSISTOR COMPOUND TRANSISTOR COMPOUND TRANSISTOR TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON COMPOUND TRANSISTOR COMPOUND TRANSISTOR
COILS &TRANSFORMERS
! ! !
! ! ! ! ! !
! !
JACKS
SOCKET,CATHODE RAY,TUBE HEADPHONE JACK RCA JACK RCA JACK RCA JACK RCA JACK RCA JACK RCA JACK
! ! ! !
SWITCHES
SWITCH (LEAF) SWITCH,TACT SWITCH,TACT
J4-2
DESCRIPTION SWITCHES
SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R NVG6TLTAB222 NVG6TLTAB103 VMC293C TMC564C TCC426C VMD348A TECB10C W5RH3.5X5X1.0 W5RH3.5X5X1.0 W5RH3.5X5X1.0 W4BRH3.5X6X1.0 W4BRH3.5X6X1.0 MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT W4BRH3.5X6X1.0X2 MMZ1608R102CT CU011902 C3149004 CU291701 CU284501 C3282402 or CU282401
AWG26 5C GRAY 440MM
DESCRIPTION MISCELLANEOUS
CORD JUMPER WIRE HOLDER CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE WIRE HOLDER CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE WIRE HOLDER WIRE HOLDER CONNECTOR PCB SIDE CUSHION B CUSHION C EYE LET EYE LET EYE LET EYE LET FUSE TRANSFORMER,FLYBACK HOLDER,FUSE HOLDER,FUSE REMOTE RECEIVER RELAY SPEAKER SPEAKER TRANSMITTER RF UNIT DEGAUSS ELEMENT CRT W/DY CRYSTAL CRYSTAL CRYSTAL CRYSTAL CRYSTAL 2F0C1602 B2013H02-8P A1561WV2-2PK 003P-2100 003P-2100 A2001WV2-2P 09-5000-024-001-001
00_6232_005_006_800+ 00_6232_006_006_800+
VARIABLE RESISTORS
V1K63H3BTE VOLUME,SEMI FIXED V1K6314BTE VOLUME,SEMI FIXED A5T409Q010 A5T402Q080 A5T402Q110 A5T402Q130 A5T402Q270 024HT03553 024HT03553 024HT03553 024HT03564 024HT03564 0246C51024 0246C51024 0246C51024 0246C51024 0246C51024 0246C51024 0246C51024 0246C51024 0246C51024 0246C51024 0246C51024 0246C51024 0246C51024 0246C51024 0246C51024 0246C51024 0246C51024 0246C51024 0246C51024 0246C51024 024HT03563 0246C51024 06CU011902 06C3149004 06CU291701 06CU284501 06C3282402 06CU282401 WCL6844038 06CH823004 06CH823004 06CH012801 06CH011202 069D01001A 06972C0010 069S140419 069S450089 069S240639 067U009039 067U008029 069S280629 069S320010 069S320010 1209415910 06CH012403 06C3220703 06C32B3303 122F061502 W9L6012042 PCB ASS'Y PCB ASS'Y PCB ASS'Y PCB AAS'Y PCB ASS'Y
P.C.BOARD ASSEMBLIES
TOC-C09X-A1 IMSA-9604S-06C B2013H02-2P A2001WV2-9P A2001WV2-8P A2001WV2-11P IMSA-9604S-12C B2013H02-5P B2013H02-5P IMSA-9604S-12F
MISCELLANEOUS
CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORD CONNECTOR CORD CONNECTOR CORD CONNECTOR CORD CONNECTOR CORD CONNECTOR CORD CONNECTOR FLAT CABLE AWM2468 CORD CONNECTOR CORD CONNECTOR CORD EIS CONNECTOR CORD EIS CONNECTOR CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE WIRE HOLDER WIRE HOLDER CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CORD AC BUSH CORD EIS CONNECTOR CORD CONNECTOR CORD CONNECTOR CORD JUMPER FLAT CABLE AWM2468
! !
! ! ! ! ! !
XRY20X30BD XRY16X28BD XRY20X30BD XRY16X28BD 51MS063L FJN20A003_M EYF-52BCY EYF-52BCY RPM7138-WH10 ALKS321 YDP4010-2 YDP4010-2 R56-0487 115-V-KA35ARB ZPB45BL3R0A A51QDJ420X58 DT-26 HC-49/U-S HC-49/U-S HC-49U/S HC-49/U
RESISTOR RC................... CARBON RESISTOR CAPACITORS CC................... CERAMIC CAPACITOR CE................... ALUMI ELECTROLYTIC CAPACITOR CP................... POLYESTER CAPACITOR CPP.................. POLYPROPYLENE CAPACITOR CPL.................. PLASTIC CAPACITOR CMP................... METAL POLYESTER CAPACITOR CMPL................ METAL PLASTIC CAPACITOR CMPP................ METAL POLYPROPYLENE CAPACITOR
CH823004 CH823004 CH012801 CH011202 003P-2100 TMC-J12P-B2 A2502WV2-4P A1561WV2-A5P A2001WR2-4P B2013H02-9P B2013H02-8P A2001WV2-8P A2361WV2-2P A2361WV2-2P 9415910 CH012403 C3220703 C32B3303 2F061502
AWG26 2C BLACK 120MM
J4-3
M5T4-09Q W575047
MVDT2002
SERVICE MANUAL
COLOR TELEVISION/VIDEO CASSETTE RECORDER/ DVD VIDEO PLAYER
Chang of SH COMPLIANT
WHEN REPLACING EEPROM (MEMORY) IC
MFR'S VERSION A ADDRESS E5 DATA A5 MFR'S VERSION B DATA AA
R,METAL OXIDE
COMPOUND TRANSISTOR TNYJC05001 DTC124EKAT146 TNYJC05001 TNYJB05001 T8YJ2412K0 T6YJ1037K0 T8YJ2412K0 T8YJ2412K0 TNYTB05001 T8YJ2412K0 TPYJB05001 COMPOUND TRANSISTOR DTC124EKAT146 COMPOUND TRANSISTOR DTC114EKAT146 TRANSISTOR SILICON 2SC2412KT146 R,S TRANSISTOR,SILICON 2SA1037AKT146R,S TRANSISTOR SILICON 2SC2412KT146 R,S TRANSISTOR SILICON 2SC2412KT146 R,S COMPOUND TRANSISTOR DTC114EKT147 TRANSISTOR SILICON 2SC2412KT146 R,S COMPOUND TRANSISTOR DTA114EKAT146
COMPOUND TRANSISTOR TNAAC05002 KRC103SRTK TNAAC05002 TNAAB05003 TCAA3875SY TAAA1504SY TCAA3875SY TCAA3875SY TNAAB05003 TCAA3875SY TPAAB05001 COMPOUND TRANSISTOR KRC103SRTK COMPOUND TRANSISTOR KRC102SRTK TRANSISTOR SILICON KTC3875S_Y_RTK TRANSISTOR SILICON KTA1504S_Y_RTK TRANSISTOR SILICON KTC3875S_Y_RTK TRANSISTOR SILICON KTC3875S_Y_RTK COMPOUND TRANSISTOR KRC102SRTK TRANSISTOR SILICON KTC3875S_Y_RTK COMPOUND TRANSISTOR KRA102SRTK
E5EZTD2R2M CE
DEFECTION PCB ASS'Y A5T402Q080 (VERSION A) TMC564C A5T402Q110 R803R9750F CRT PCB ASS'Y (VERSION A) TCC426C RC 75 OHM 1/16W
DEFECTION PCB ASS'Y A5T410J080 (VERSION B) CME029A A5T410J110 R803R9680F R803R9153J R803R9561J R803R9561J CRT PCB ASS'Y (VERSION B) CCE024A RC RC RC RC 68 OHM 1/16W
DVD PCB ASS'Y (VERSION A) A5T402Q130 VMD348A 06C3220703 CORD CONNECTOR C3220703 OPERATION PCB ASS'Y A5T402Q270 (VERSION A) TECB10C 06C3149004 098S210461 CORD CONNECTOR CRT W/DY C3149004
OPERATION PCB ASS'Y A5T410J270 (VERSION B) CEE055A 06CU149003 098Q210464 CORD CONNECTOR CU149003 CRT W/DY A51AKL13X04(M)
A51QDJ420X58
VCR PCB's, DEFECTION's, CRT PCB's, OPERATION PCB's and DVD PCB 's are not interchangeable.
Q2302
R4081 B4002 R4009 C4053_1 R4044 C4071_1 Q2301 R2332 C2327_1 D8101 R8121 Q8101 C2346_1 R2333 R8116 R2360 R2306 R4041 C4039 W854 C4070_1 C4062 C4063 C2343_1 C4095 C4084_1 C4067_1 C4021 C4064 C4068_1 R4054 R4051 R4053 R4050 C4044 C4077 R4049 C4017 C4016 W840 C4083_1 C4001 L4001 B4006 CD4002 B4009 R4077 R4078 C4078_1 C4008 R4063 C4087 R4060 C4088 R4008 R4014 C8119_1 C4038 L8104 C4081 B4010 R4071 IC8102 R4058 R4027 R4026 C4098 R4025 C4028 R4002 C4031 R4021 W842 X4001 R4004 R4005 R4003 R4031 C4094 C4093 C2307 C4069_1 C2314_1 HS2301 R4020 R4019 R2338 R2330 R4001 R4017 IC2301 R4080 R4040 R2340 C4089 C4076 C2340_1 C2341_1 IC4003 C4042
R4070
C2348 C2328_1
C2309
C2316
C4091 D4001 R4011 C4090 R4013 Q4004 R2362 IC2304 W816 R4061 IC4007
B4005
CP2301
R2303
53
R4062
R4048_1 C4047_1
C2303
W847 C4032
C4074
C8126
105
157
R2324
R2327
W820 C8112 CP8101_2 W824 W819 L8102 IC4002 W818 D8112 D8111 C8121_1 C4037 R4035 C8110 W826 L8103 C8104 C8107 C8109
W875
R2323
R2329
C8108 R4016
C8105 R2302 R4036 R4037 C4035 C8106 R4012 D4003 R4042 C4034 C2301
C8120
B8103 R4076 C4025 C4024 R4064 W835 R4059 C4023 C4022 C4020 C4019 R4073
C4066 D4002
W850 B4008 C4099 C4072 C4080 C4097 C4104 C4065 C4036 C4082
C4092 B4003
C4015
C4052
C4012 C4075
C4050_1
C8113
C4040_1
W825 R8115
C4060
DME031A
IC4009 R4038 C4059 C4045_1
W836
C4026 R4045
C4013
D4004
C4014 C4018
IC4008
R2319 D2303 R2305 R2307 C2304 R2335 R2334 R2326 R2301 R2308 C4085 C2313 R2321 CP2302 D2304
R8114 R8112
CP2303
R2325
R2337
DME031A
C2357 B4018 C4004 B4001 C4030 W806 R4043 W834 C4033 B4014 C4002 R4057 C4010 C4051 B4016 R2339 R4022 C2318
B4013 C4057 B4012 C4056 B4011 C4003 R2309 B2303 B2304 B2305 B2302 C2350 W843 R2355 R2348 R2359 R2347 C2342 Q2304 Q2305
C2347
R2356
C2332
C2331
R2346
Q2303
C2326
R2318 R2341
B2301
CD1702
B8001
CP601
W007 D1732 D1711 D1702 W899 R4205 CD1704 R4220 C1701 W028 W026 C1714 C3002 CD1703 R4239 R3001 Q3003 D1710 C4211 C3009 D1705 C3004 CP1704 R1722 R1714 RY1701 R1702 D3008 W012 W020 W023 W912 W031 W898 C17 07
_1
J8007
J4202
FH1701 F1701
FH1702
W843
W006
HS351
R353
R356
W010
TU001
W018 W027 Q3002 R3010 W016 C3011 W913 C3007 W008 R3004 Q3007 C1716 Q1705 R1717 R1724 D1718 R1721 HS1701 W894 D1715 C1715 C1711 R1706 D1703 IC1702 C1732 W030 D1730 C3005 R1731 W001 R3006 CP1707
C321 R359 C328 IC352 W005 W011 D3011 W004 R311 W015 HS3001 W041 CD002 R3014 R3009 C3008 Q3005 C1733 R1703 D1716 C1713_1 S817X W903 W888 D1704 D1722 W094 T1701 W013 W089 C326 R309 R3028 R310 S808Y W065 D1723 C3010 CP8001 D3003 CP1702 C1705_1 W821 W082 W081 D1734 C1724
D1 71 9
CD1705
W047 W051 W052 W073 W042 W043 W036 W044 W037 W045 W039 W040 W074 W071 W072 W078 W075 W080 W076 W077 S801X C3025
C172 9_1
C323 C327 C315 C311 C309 R3003 W048 W053 R3002 D3001 W344 W343 C310 L301 L1505 W058 S817Y R1725 W086 W035 D1724 VR1701 R1712 R1710 W050 W049 W034 D1713 IC1701 C3028 W083 D1726 D1727 W848 C306 C308 B1703 D1721 C305 C1720_2 C329
D1733
D106
W038
W046
W057 C4529 W092 W877 C5554 R5512 C5536 C4532 C4523 C4518 W145 CP4501 W152 C4548 C4544 C4508 S808X W151 C5544 L5503 W153 C5559 C5533 C5531 C5519 C5530 W159 C5543 R5524 C5545_1 R5516 W084 W856 R5511 W864 W059 W060 C5555_1 W108 W062 W132 C4506 CP603 W144 C4511 W112 W128 D603 L4502 W138 W136 W127 W139 W123 W124 W126 R605 W892 W119 W118 W143 W116 W115 W114 Q4504 R613 L1502_1 W098 L602 C4576 W121 C4571 C4564 C4565 W149 C4567 W141 W846 D602 L4509 W183 C1518 L1501 C4572 W166 C1528 W219 W870 W175 R602 W181 W232 R1516 W221
Q101
W055
W088
C320
D4207
(MFR'S VERSION B)
S801Y
SOLDER SIDE
R8012
W105
C5502 C5526 C5525 C5542 L5501 C5515 C5520 C5524 D5501 L8001 C5523 C5551 C5512 W157 W146 C8013 C5514 W158 C8006 CP4503 R5501 W148 C5507 W261 W272 C5540 C5505 C8001 W834 W266 C5528 C5508 W260 W250 D3007 L5502_1 Q3010 D3002
R302 1
R616
CP
W820
W104 W099 W137 R4557 C4581 C4558 W192 W874 W201 W215 W224 W223 W164 C4574 D605 W197 D5502 W234 C4570 R4559 L4506 R4537 C4550 W102 W205 D601 W359
C4566
C4545
W103
C612 D4204
W122 R4238 L601 W133 W117 W130 W129 R4522 W150 C4543
10
C103
W161
C4547
W174 W165
L4505
W208 W213
W169 W238 W200 W187 W198 W190 W193 W226 W195 W188 C126 W217 W171 W908 W827
W236
W350
C5564
W357
W246 W245
W256
W243
W255
W248 W247
W244
W273
X601
W173
W227
W252
W249
W845
C102 W186 W184 W196 W233 W220 W819 W810 W162 W203 R4563 R4562 W859
C3016 W269 W214 W218 W258 D101 W270 C104 W212 R153 W225 W854 W253 W262 W265 W275 C1534 W254 W276 R1519
W833
C113 W163 C632 W170 W194 R632 W202 W199 R114 W352 W206 W185 W338 W191 W189 W176 W172 R131 R623 C119 D103 W179 W180 W289 W282 C122 D108 W294 W278 W292 W293 W178
S101X W222
W271 C1520 W182 W239 W237 L8003 C8009 X102 W235 X101 W325 W326 W327 Q107 C8007 W268 W263 L1506 W336 TP5501 W259 W264 C1536
R113
R122
10
R125
Q1
08
R3020
L5504
W322
C8015
R128 W841 W842 C8005 W315 W331 W332 W333 W309 W308 W307 W312 W316 W335 R4528 W358 C139 D4201 W297 W296 W321 W305 W304 W303 R8024 C8023 W806 W306 W310 S101Y R144 R8025 W328 W319 W311 W318 C8065 W323 C8022 SW101 C8002
R8022 W850
C2210 C2212
W844
W816
W299
W286
W300
C8003 W880 C8004 R2225 C8102 R2226 C2206 C2208 W334 W337
W295
R2224
R2223
R2227
R2211
R2212
CP2201
W838
D4205
D2206
D2205
D2207 OS2201
SW2207
SW2206
SW2205
SW2204
SW2203
SW2202
Q103
TP4501 TP102
DME034A
B2201
CP303
W033
L3001
C1728_1
D1720 D1728
C1717
D1712
W063 W342
R1727
W056
W002 W014
C3023
Q3014
CP1708
R3008
L4205 C3022
TH1701
D1709 Q1706
C4204
R3015
TP4201
C4213 R8003 C8010 R8005 R4217 C4209 C4214 C4203 W900 Q4212 R1705 Q4203 R8004 Q8002 R4231 C8095 R8013 R4203 R4207 Q4211 R4214 Q4210 C4202 R4232 Q4202 R8006 C004 R8007 C4210
Q4201
C358 R1708 W829 C4208 C3014 R3024 Q3015 C3001 R3017 R301 Q350 R357 Q3011 W811 R307 C302 R3016 W837 C001 R3031 Q3009 Q3008 R3026 R3025 R3013_1 Q3006 R3012_1 C3003 R3007 Q3001 Q3004 R3018 R3011 R3019 C006 C318 C3024 C317 W815 C314 C312 R4212 C3027 C8017 W346 W347 W831 R1719 R1713 C8019 C325 C319 C316 IC302 R3027 W021 W009 W022 R3005 R302 C304 C307 R4218 R306 R304 W353 W886 R4216 R4215 IC602 C112 R4511 W804 C5553 R4531 C4524 R4501 R4507 C4537 R4520 C4542 C4541 R4532 R4533 C5558 C5560 R4527 C4517 C4536 C4533 R4526 R4529 C5549 C4514 1 R4513 C1525 R1517 R1518 C1504 R603 C8020 C8044 Q4204 R4540 R4536 R4219 W361 Q1502 Q605 Q8006 R1510 R618 W360 Q1503 Q8007 R628 C634 R611 W349 C617 C614 C1519 C1515 C1509 C1506 C1517 R1501 IC1501 C613 R608 C607 R633 R612 R634 Q601 R617 C611 C608 17 IC1502 R110 C118 R115 R116 C618 R615 C619 R1508 C1514 R1505 C1508 R610 Q602 C606 R609 R607 C1530 C1501 C1510 R619 C601 C621 C622 C1531 Q1501 33 R101 R124 C101 C106 C117 Q114 R165 Q110 Q2201 Q2202 Q2203 R8001 C2201 R2206 R2208 C2205 R152 C143 R1513 C1523 R1512 W351 R1507 R1511 C1511 C1507 C1505 R4508 C4512 C4513 R4510_1 C4501 R4503 R4550 C4551 C4553 C4552 R4546 R4502 C4557 R4521 R4519 C4534_1 C4573 Q4503 R4509 Q4506 Q4501 Q4502 R4505 R147 R4553 Q4511 R305 R303 17 C5565 C5557 C5566
SOLDER SIDE
(MFR'S VERSION B)
IC
R1502 R624 C626
R134 1
60
W887
1
49 C138
R4523 R4525 IC1505 C1538 C4580 R1515 Q102 C1537 R1504 C1502 C1513 R1506 R1503 C1512 C164 R103_1 C630 C629 C628 R625 R626 C627 C625 R620 C631 C616 R159 Q116
C137 R636 R148 R1520 R1509 Q606 R108 C110 R106 C109 C604 R104 R164 R630 R160 R149 R150 C114 R177 C116 Q112
R4530
C131 C125 C152 C132 C127 C121 C156 C130 R129 C133 R112 C135 C123 R118 R176 51 R132 R135 R111 C111 C154
C148 C145
IC1504
W883 C144 R136 W851 1 IC103 C8090 R8056 C140 R133 R8027 C8070 R8054 R8049 R119 R4204 Q106 R123 R8023 R8051 IC8004 R8050 R8052 R8053
R139
C120
R166
10
C151 76 26
C8079 C8081 R8048 C8064 R8026 R8047 R8020 C8025 C136 R8021
C8077
C2207
C2209 C2213
DME034A
C5556 Q4509 C4579 R4539 R4534 C4546 R4541 R4545 C5522_1 R5504 C5517 R5502 C5503 C4535 R5508
IC
45
IC
01
R3023 C5534
C1709
R1715 C1722
W881
IC
33 C4522 21 61 C4521 C4505
55
01
C5518 49 C5563
C5529 C5501 41 C5550 R5514 C4538 C4549 Q4507 R4524 R5519 C5513 C5509 R5503
ADD C112
(DVD PCB)
(MFRS VERSION B)
B4013
C4096 C4086 0.001 B C4085 0.001 B 0.001 B C4032 0.001 B AFEGND R4043 10K +-1% 10K +-1% 0.1 F
C4057 180P CH
C4042
4.7K
10P CH
R4013
47K C4043
R4052
47P CH C4091
2.9
B4018 MMZ1608R102CT
W840
TP4026
6.3V 47 KA C4068_1
0.1 F
0.1 F
SYS_MUTE DAC_VIDEO_C DAC_VIDEO_B DAC_VIDEO_D ASDATA0 ABCLK ALRCLK AMCLK MD MC ML RESET P.CON+A5V P.CON+5V GND (GND,D_GND)
FPCSTRB
MMZ1608R102CT
IRRCV
C4067_1
R4036
C4075
15K 0.1 F
0.1 F
B4016 MMZ1608R102CT
C4088
C4076
R4063 C4051
C4033
B4002 (120mA) MMZ1608R102CT B4003(250mA) (D_GND) FROM/TO MOTOR DRIVER TRAY_OPEN TRAY_CLOSE HOME TOUT_SW TIN_SW DVD_CD DRVSB RF OPU_A OPU_B OPU_C OPU_D OPU_E OPU_F VC SPDL_SENSSPDL_SENS+ VR_DVD VR_CD DVD_LD CD_LD SPINDLE_PWM SLED_PWM TRACK_PWM FOCUS_PWM P.CON+A5V P.CON+3.3V VCC+9V ADCIN_5 ADCIN_6 ADCIN_7 M_GND (GND,D_GND) GND (D_GND) C4104 C4097 0.01 B C4036 0.1 B 47 KA C4065 0.01 B C4092 100P CH C4084_1 0.001 B TP4012 TP4011
C4002 R4061
R4060 R4062
R4022
C4004 0.1
FROM/TO MEMORY
6
HA0 HA1 HA2 HA3 HA4 HA5 HA6 HA7 HA8 HA9 HA10 HA11 HA12 HA13 HA14 HA15 HA16 HA17 HA18 HA19 HD0 HD1 HD2 HD3 HD4 HD5 HD6 HD7 HD8 HD9 HD10 HD11 HD12 HD13 HD14 HD15
GND P.CON+3.3V 3.3 3.3 3.3 3.0 3.0 3.0 3.3 3.3 0 0.5 2.6 0 0 1.9 0 0 0 2.1 2.0 NC 0 3.3 0.6 3.3 2.6 1.8 2.7 2.9 0 0 0.5 0 0 0.6 0 0.6 2.7 2.7 0.6 0.4 5.5 3.3 0.4 3.3 0 0 0 3.1 3.1 3.2 0 3.3 3.3
208 207 206 205 204 203 202 201 200 199 198 197 196 195 194 193 192 191 190 189 188 187 186 185 184 183 182 181 180 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163 162 161 160 159 158 157
0.1
F R4045
C4008 HA15 HA16 HA14 HA13 HA12 HD15 HA11 HD7 HA10 HD14 HA9 HD6 HA8 HD13 HD5 C4010 HD12 WR HD4 HD11 HD3 HA19 HD10 HA18 HD2 HA17 HD9 HA7 HD1 HA6 HD8 HA5 HD0 HA4 RD HA3 HA2 MEMCS0 HA1 HA0 BOOTSEL1 BOOTSEL2 C4014 0.1 F 0.1 F 0.1 F
NC
1M
R4012
C4013 0.1 F
MEMCS0 RD WR SD_A0 SD_A1 SD_A2 SD_A3 SD_A4 SD_A5 SD_A6 SD_A7 SD_A8 SD_A9 SD_A10
100
6.3V 100 KA
C4078_1
C4083_1
C4082
1K C4077 0.1 F
100 KA
100 KA
C4011_1
C4012
0.1 F
C4053_1
100 KA
SD_D0 SD_D1 SD_D2 SD_D3 SD_D4 SD_D5 SD_D6 SD_D7 SD_D8 SD_D9 SD_D10 SD_D11 SD_D12 SD_D13 SD_D14 SD_D15 RAMCS0# RAMCS1# RAMRAS# RAMCAS# SD_BA0 RAMDQM RAMWE# RAMCLK RAMCKE
R4080 R4009
C4090
C4026
61 62 63 64 65 66
R4054 1K R4053
0.9 0.3 1.0 0 1.0 3.3 0 1.0 0.2 0 0.2 1.8 1.9 0 0.2 3.3 0 3.1 0.5 0 3.1 0.2 3.2 3.3 3.2 0 0 1.5 3.3 2.1 0 1.3 0.8 0.8 3.3 1.7 1.3 0.5 0 0.9 1.8 1.4 0 0.5 3.3 2.0 0.4 1.5 0 0.8 1.2 1.5
NC
UNREG+3.8V
0.1 F
0.1 F
0.1 F
0.1 F
0.1 F
0.1 F
MMZ1608R102CT F
TP4023
C4080
SSCRXD MEMCS(1) VDDP MEMAD(15) MEMAD(16) MEMAD(14) MEMAD(13) MEMAD(12) MEMDA(15) MEMAD(11) MEMDA(7) GNDP MEMAD(10) MEMDA(14) MEMAD(9) MEMDA(6) MEMAD(8) MEMDA(13) MEMDA(5) MEMAD(20) VDDP MEMDA(12) MEMWR# MEMDA(4) VDDC MEMDA(11) MEMDA(3) MEMAD(19) GNDC MEMDA(10) MEMAD(18) GNDP MEMDA(2) MEMAD(17) MEMDA(9) MEMAD(7) MEMDA(1) MEMAD(6) MEMDA(8) MEMAD(5) VDDP MEMDA(0) MEMAD(4) MEMRD# MEMAD(3) MEMAD(2) MEMCS(0)# MEMAD(1) MEMAD(0) GNDP VDD-IP VDDP 53 54 55 56 57 58 59 60
75 +-1% R4004
68 +-1% R4003
75 +-1% R4002
RAMADD(6) VDDP RAMADD(1) RAMADD(7) RAMADD(0) GNDP RAMADD(8) VDDC RAMADD(10) GNDC RAMADD(9) VDDP RAMADD(11) RAMCS(0)# RAMBA(1) RAMBA(0) GNDP RAMCS(1)# RAMRAS# RAMCAS# VDDP RAMWE# RAMDQM GNDPCLK PCLK VDDPCLK RAMDAT(8) GNDP RAMDAT(7) RAMDAT(9) RAMDAT(6) VDDP RAMDAT(10) RAMDAT(5) RAMDAT(11) GNDP RAMDAT(4) VDDC RAMDAT(12) GNDC RAMDAT(3) VDDP RAMDAT(13) RAMDAT(2)
SPDIF EN 1 5.0 VCC2 2 3.6 VCC1 3 3.6 GND 8 4 0 VO1 5 3.3 VO2 6 1.8 ADJ 7 0.8 R4081 3.9K +-1%
JG020
MMZ1608R102CT 150
10V 100 KA
B4010
R4071
10P CH
R4014
4.7K
TP4019 0 0 W836 1.6 1.6 R4042 120 1.8 3.3 C4069_1 0 6.3V 47 KA 0 3.3 3.3 HOME 0 PM16 JG028 3.3 (MIC_DET) 3.3 NC (DJTDO) 0 I2C_CLK 0 I2C_DAT 1.8 0 0 (ICETCK) 3.3 (ICETDO) 3.3 (MUTEC) 3.3 (ICETMS) 3.3 3.3 (PM11) 0 3.3 TP4017 3.3 TP4018 3.3 R4024 3.3 4.7K 1.7 0 1.7 1.6 0 1.1 0 ASDATA1 0 ASDATA2 1.6 0 MIC_ON 0 NC 0 0 3.3
C4034
75 +-1%
208 SSCTXD
GNDDACBS2 GNDDACP RSET C/B/U VDDDAC Y/R/V CVBS/C VDDDAC 160 A CVBS/G/Y 159 G Y/C 158 RFN GNDDACD GNDDACD 157 RFP GCLK XO VDDA RESET# GNDA GNDP VDDP IDGPCI/O(2) GPCI/O(31) DJTCK / ICGPCI/O(3) / VID(0) DJTO / GPCI/O(30) / VID(1) DJTDI / GPCI/O(29) / VID(2) DJTMS / GPCI/O(28) / VID(3) MPEG/MICON/DSP/RF_AMP IC VDDC GNDC IC4001 GPCI/O(27) ZR36862PQCG IDGPI/O(1) ICGPCI/O(2) GPCI/O(26) VDDP ICGPCI/O(1) GNDP HSYNC VSYNC AIN VDDP-A2 AMCLK 100 RAMDAT(14) GNDP-A2 101 GNDP ABCLK ALRCLK 102 RAMDAT(1) GPAI/O 103 RAMDAT(15) AOUT(0) AOUT(1) 104 RAMDAT(0) AOUT(2) SPDIF IDGPCI/O(0) ICGPCI/O(0) GNDP GPCI/O(20) VDDP 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104
105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156
52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
R4005
L4002 W5T29X7.5X19
C4030
33 33 33
TP4008
FROM/TO POWER DVD/VR 130mm DVD COMBO 250mm CD4002 (CP8001) CU2B3301 GND(D) GND(D) TX 1 2 3 4 5 6 7 8 9 10 11
R4031 R4035
4.7K 4.7K
100P CH C4093
C4037
R4073 R4076
33 33 C4031 0.01 B IAMCLK IABCLK IALRCLK JG024 R4058 TP4015 TP4016 C4098 R4025 R4026 R4027 220 220 220
0.1 F
3.2
3.2
SDA
SCL
WP
VCC
6.3V
STBY_L
JG021
TP4013 TP4014 TP4020 L4001 2.2uH 0305 TP4027 C4066 1 B W850 TP4021 TP4022
C4094
GND 4 0
NC 3 0
NC 2 0
NC 1
ABCLK ALRCLK
0.01
C4018
C4019
C4020
C4024
C4023
C4025
R4059
6.3V
0.1
6.3V
6.3V
RAMCS0# SD_BA0
RAMWE# RAMDQM
PCB130 DME031
RAMCLK
SD_D12
SD_D8
1
2
SD_A10
SD_D4
SD_D3
SD_A8
SD_A9
TP4003
1
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY ARE PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
A
0 4 -VS 0 3 0 2 + +VS + 5 0.2 0.2 R2362 6 0.3 3.3K 7 5.2 R2361 2.2K 0.1 NC 1
C2350
DM3P(05SD)
7
FROM/TO LOADER CP2301 09-5000-024-001-001 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 GND F Vref VCC E D C SW1(DVD/CD) VRF(RF_OUT) B A VR(DVD) VR COM VR(CD) GND LD(CD) PD/GND LD(DVD) GND NC T DRV T RTN F DRV F RTN NC
B C2329_1 R2360 R2355 6.3V 47 KA C2331 0.1 B JG012 OPU_E OPU_D OPU_C DVD/CD RF OPU_B JG016 JG011 JG014 JG013 JG040 0 W843 0 6.3V 47 KA C2328_1 DVD/CD SW Q2304 0 KTC3875S_Y_RTK 0.7 R2347 3.3K TRACK_PWM 0.2 0 JG015 OPU_F OPU_VREF 1K
R2356
33
82
W804 (RF_GND) 6.3V 47 KA C2347 6.3V 47 KA C2343_1 C2346_1 0.001 B W875 (D_GND)
R2359
C2332
0.1 F C2342
0.1 F
0.1
R2346 3.3K
RF_A5V
C2318
DRVSB R2339 1.2K SPINDLE_PWM SLED_PWM FOCUS_PWM ADCIN_7 ADCIN_5 ADCIN_6 F C2326 0.1 VCC+9V TP2320 M_GND SPDL_SENS+ R2334 10K SPDL_SENSTP2323 TRAY_CLOSE R2324 1K R2319 56K 3.3K TP2324 TRAY_OPEN
CDLD C2327_1 DVDLD JG056 TR+ TRFO+ FODVD LD CTL Q2301 2.6 2SA1036K 2.3 JG017 R2306 6.8 R2318 6.8 R2332 JG018 47 KA 6.3V
0.1
R2308
TP2322
TP2307
R2307
TP2303 MOT_LDMOT_LD+ R2353 TOUT_SW 100 R2352 100 R2350 4.7K R2351 4.7K TP2305 TP2304 P.CON+3.3V 100P CH C2360 100P CH TIN_SW B2301 MMZ1608R102CT DVDLD
75K
1K
R2309
220
R2301 10K
R2321
R2326
10K
TP2318 5.6K
TP2321
R2327
R2305
CDLD
R2338 6.3V 100 KA R2333 220 3.2 R2340 LA6565-TE-L-E TP2308 MOTOR DRIVE IC 6.8 R2341 JG019 6.8 W816 12K
MMZ1608R102CT
NC NC NC NC NC NC 0 4.0 2.6 2.6 1.5 1.5 1.6 1.5 0 0 1.0 2.5 4.2 0 1.5 1.5 1.7 1.5 1.5 36 35 34 33 32 31 30 29 28 38 27 26 25 24 23 22 21 20 19 VCONT MUTE1 VREF-OUT MUTE234 S-GND REG-OUT VIN+OP VO_OP VIN4VIN-OP VREF-IN VIN3REG-IN VIN2VIN4 VIN3 VIN2 VIN2+ R2337 10K
TP2319
C2341_1
27K
4.7K
R2335
VC2
100 +-1%
1.9
R2342
4.7K
C2358
100P CH C2359
100P CH
VIN1+A
VCCS
C2357
VCC2
IC2301
VCC1
VLD+
VD4+
VD3+
VD2+
VD1+
VLD-
VD4-
VD3-
VD2-
VD1-
FWD
REV
VIN 1
VIN1-A
1 0
5 TP2309
6 TP2310
7 TP2311
8 4.1 TP2312
37
10 TP2314
11 TP2315
12
13
14
15
16
17
18
100 MOT_SLEDMOT_SLED+ MOT_SPDLMOT_SPDL+ C2301 0.1 C2313 0.1 B C2302 R2303 C2303 F
TP2316
1K
C2314_1
C2310_1
C2306 0.1 F
FROM AUDIO/VIDEO
0.1 B 2.2 0.1 B 2.2 R2323 C2307 1.2 R2329 0.1 B JG057
CD_LD_CTL
R2304
MOT_SPDL+
MOT_SPDL-
MOT_SLED-
CD_LD_CTL
MOT_SLED+
1.2
C2304
0.022
JG058
MOT_LD+
C2305
MOT_LD-
TR+
FO+
TR-
FO-
0.1
PCB130 DME031
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
(DVD PCB)
(MFRS VERSION B)
C/B/U
Y/R/V CVBS/C W818 FROM/TO MPEG/MICON/DSP/RF_AMP DAC_VIDEO_C 150P CH C8105 12P C8104 CH 150P CH C8106
1uH
0305
CD_LD_CTL W819
D8101 1SS355
DAC_VIDEO_B 150P CH
6
RESET MC MD ML AMCLK ABCLK ALRCLK ASDATA0 SYS_MUTE P.CON+A5V GND (GND,D_GND)
0.7 3.2 0
560
560
L8102
R8116
R8121
P.CON+A5V
DAC_VIDEO_D 100P CH
W820 NC 33P CH C8112 NC NC NC RESET ZERO D8111 1SS355 TP8102 TP8103 TP8104 TP8105 W825 TP8106 TP8107 TP8108 R_AUDIO L_AUDIO DAC_B_VIDEO DAC_C_VIDEO TP8109 TP8110 W824
TP8101
FROM/TO DVD IN/OUT DVD/VR 95mm DVD COMBO 180mm CP8101_2 (CP8002) IMSA-9604S-12F
C8110
W826
DVD-H(GND) DVD RESET ZERO AUDIO-R GND AUDIO-L GND Y GND C GND CVBS
TP8111
(D_GND)
C8119_1
100 KA
C8120
0.1
B8103
R8115
100K
100K
TO MEMORY
6.3V
SYS_MUTE
RESET
TO MOTOR DRIVER
1 B
CD_LD_CTL
8 VOUTR
2.5
7 VOUTL
4.9
6 VCC
3.3
NC 5 VDD
4 DGND
1.6
3 LRCK
1.1
2 DATA
1.6
3
1 BCK SCK
ZEROR/ZEROA
ZEROL/NA
VCOM
AGND
MD
MC
9 0 2.4
10 3.3
11 0
12 NC
13 0
14 15 16 0 3.3 1.7
25V 10 KA
C8121_1
ML
2
ASDATA0 ZERO ALRCLK AMCLK ABCLK MD MC ML
PCB130 DME031
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
R.SIGNAL + COMPONENT SIGNAL(U) B.SIGNAL + COMPONENT SIGNAL(V) PLAYBACK COLOR SIGNAL AUDIO SIGNAL(PB)
D E
(VCR PCB)
P.CON+5V_A Y/C_DATA Y/C_CS Y/C_CLK
(MFRS VERSION B)
P.CON+5V_A FSC
22K 1/4W
R4528
R4523
L4506
3.3K
47uH 0305
R4545
22K
R4530
W864
50V 1 KA 6.3V 47 KA
FROM REGULATOR
W854
R4525
R4506
12K
12K
1K
0.1
C4543
50V 1 KA
C4547
1.8K
P.CON+8V P.CON+5V_A
R4524
C4538
C4545
47K
S808X
S808Y
W880
NC
0.1
0.022 B
C4546
0.022 B
C4556
C4549
0.01 B C4558
C4535
R4534
R4539
C4550
X4501
HF1
100CT3R502 3.579545MHz
HF_COM Y/C/AUDIO/HEAD AMP IC IC4501 LA71205M-MPB 0.5 60 C4521 0.068 B C4522 C4514 0.047 B 0.047 B 2.2 61 0 62 4.0 63 1.8 64 0.7 65
P
50V 1 KA
HF2
1.5K
FSC
8.2K
FROM/TO MICON Y/C_CLK Y/C_DATA Y/C_CS H.SW VIDEO_OUT ENV_DET VCR_A_MUTE CTL+ CTLC_ROTARY DUMMY_V.SYNC V.REC_ST_H R4557 C4565 82K 1/4W R4560 100K C4570 C4566 50V 1 KA C4569 0.1 B C4567 FROM DVD IN/OUT 50V 0.22 KA C4564 10V 33 KA FROM/TO DIGITAL COMB FILTER C4576 DVD_VIDEO 50V 1 KA 50V 4.7 KA C4572 TUNER_VIDEO 50V 1 KA V.SYNC W870 AUX_V[F/R] FROM CHROMA/IF C4574 50V 1 KA H.AMP_SW1 COMP Y/C_VIDEO
6
FROM/TO CYL CP4501 TOC-C09X-A1 9 CD4501 2F061502 8 7 6 5 4 3 2 HF1 (R) HF COM HF2 (L) SP-CH1 (R) SP COM SP-CH2 (L) EP/LP-CH1 (R) EP/LP COM EP/LP-CH2 (L)
59
OUT ENV COMP DET KILL DET HA GND CHROMA DET ACC DET
SERAIL DECODER
VX01
320FH VCO
P R
SLD
PLL OUT
VSS
40
C-VCC
ALWAYS VDD 5V
4Fsc
CLOCK 0
1.7
TIMMING DRIVER CCD
BGA BGA
OUT
39
38
REC APC
PB APC
REC AFC
BEFORE
IN
AFTER
0.7 66
R H
P R
BGA
R P
25V 10 KA
R4559
2.8
0 58
0 57
0 4.8 4.8 4.8 5.0 1.9 2.6 4.0 3.3 3.3 2.3 5.0 5.0 56 55 54 53 52 51 50 49 48 47 46 45 44
NC
0 2.2 0.8 43 42 41
0.7 67
P
68
HA VCC
47 KA
C4508
1.7 69
P
P.CON+5V_A
W891
5.0
C-LPF
Main CONV
34 2.6
REG 4V BAL TC1
3.58M BPF1
PB-C
0.33 B
C4505
6.3V
1.8 70 0 71 2.0 72
P H L R
1 2 3
YNR/COMB
P R R
VIDEO AGC
CLAMP
P
2.0 73
PB-C
1/2 FBC
R P R P
NL EMPHA FM MOD
R-EQ TEST NORMAL
Y-LPF
R
74
2.0
P
Y/C MIX
0 75
A-GND
1 2 3
2.2 76 4.9 77
A-VCC ALC DET PB,EE EQ AMP SP,LP PB,EE REC:LP<EP PB:EP VREF REC AMP MUTE
P R
DOUBBLE LIM
FM DEM
26 3.6 NC 0 4.9 L4509 P.CON+5V_A R4550 C4568 2.2M R4562 11 100uH 0607 Y/C_VIDEO 180 1/4W 25
ALC
R P
LPF
LINE AMP
2.3 78 C4523 C4517 0.1 B 16V C4524 0.1 B R4512 10 1/4W W877 C4529 6.3V 470 YK C4532 22 KA 0 79 2.0 80
Vref 2.3V
Y-VCC
VHS
SOPB
FM AGC
PB FM EQ S-EQ
180 1/4W
NORMAL_A
R4504 12K
R4505 SW Q4503 KRA103SRTK 0 5.2 COIL,BIAS OSC L4502 5.3 1626009 6 5 4 MMTS 1 2 3 8.2K 6.3V
C4518 220 KA
2 2.3 0.1 B
3 2.2
4 2.2
5 2.5
6 2.3 C4541
7 2.2 0.0022 B
8 2.3 R4533
9 2.4 820
10 5.0
11 1.0
12 1.0
13 1.7 13
14 1.4
15
16 0
17 0 NC 1.5 C4551
18 0.1
19 2.2
20
R4553
100
FM AGC FIL
Y-GND
4.7K
24
REC FM-EQ
0.33 KA
FROM/TO HEAD AUDIO CONTROL CP4502 IMSA-9604S-06C 6 5 4 3 2 1 AUDIO REC AUDIO PB CTL+ CTLAE HEAD(+) AE HEAD(-) CTL+ CTL-
TP4501
50V 4.7 KA
C4544
V.REC_ST_H
W846
R4520
V.ENV
P.CON+5V_A
NC R4536 8.2K C4581 6.3V 220 KA 16V 100 KA C4573 0.1 B P.CON+8V_B
R4509 680 BIAS CTL Q4505 KTA1266 0 4.9 4.9 3.3K R4511 22K 0 0 R4510_1 BIAS OSC Q4504 C4527 KTC3203_Y 6.3V 47 KA 0 2.2 1/10W R4507 W856 4.8 0 AMP Q4506 KTC3875S Y_RTK R4519
R4540
100
C4548
50V 0.33
560 0 AUDIO PB SW Q4501 KTC3875S_Y_RTK 0.7 0 C4506 0 AUDIO PB SW Q4502 KTC3875S_Y_RTK 0.7 R4503 10K R4502 10K
50V 3.3 KA
R4521
1.8M
15
39P CH
C4553
C4557
W804
C4571
R4501
150P CH
L4504
KA
820P CH
220K 1/4W
25V 10 KA
C4511
C4539
100V 0.022
C4534_1
0.015 B
0.0047
1M
C4501
6.3V C4513
1.5K
0.0022 B
R4522
14
R4531
180
V.SYNC
1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
CAUTION: DIGITAL TRANSISTOR NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
RECORD LUMINANCE SIGNAL RECORD COLOR SIGNAL PLAYBACK COLOR SIGNAL PLAYBACK LUMINANCE SIGNAL
G H
(MFRS VERSION B)
8
8
FROM/TO REGULATOR VIDEO_OUT B CENT_LED_CTL CONTROL_IN SDA SCL CYL_DRIVE H.SYNC V.SYNC Y/C_VIDEO 100P CH HIFI_H.SW DVD_H AT+5V SCL 5.0 EEP ROM IC IC199_1 BR24L04F-WE2 8 VCC 0 7 TEST 4.8 6 SCL A1 C133 X101 15P CH 100DA32R01 C131 32.768KHz 15P CH C132 0.1 B 10P CH C135 10P CH AV_SW2 SDA 4.8 5 SDA A0
R111
4.7K
C121
68P CH
C145
150P CH
W859
0 S101X
C137
5.6K
0.18 B R131
C152
28
C130
BACKUP+5V AT+5V
P.CON+5V_A
C148
C151
68P CH 0.1 F
1/4W
C138
0.022
R134
A2
5.6K C126
VSS
10K
1 0 0
2 0
3 0
R132
56K
R139
27 FROM/TO Y/C/AUDIO/HEAD AMP 10V 100 KA C125 0.1 B Y/C_VIDEO Y/C_CLK Y/C_DATA Y/C_CS H.SW VIDEO_OUT ENV_DET VCR_A_MUTE CTL+ CTLC_ROTARY DUMMY_V.SYNC V.REC_ST_H H.AMP_SW1 COMP VCR_A_MUTE C114 TV_POWER_H 0.01 B R112 100
47K
0.001 B
R141
R147
47K
DRUM_PWM
NC NC NC NC NC NC 2.2 1.6 0 0 4.7 4.9 0 0 5.0 3.3 1.0 0 0 0 5.0 4.9 3.6 3.6 2.7 0 0 5.0 5.0 0 3.5 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 CAP_PWM CENT_LED_CTL DVD_H AV_SW2 HSYNC CAP_FULL OSCO VSYNC VDD NC NC XO CVIN VSS2 VSS OSCI NC NC CVIN2 SXI NC NC XI
R135
10K
10K
FROM/TO DVD IN/OUT TX RESET DUMMY_V.SYNC R153 1K 1/4W R144 1K 1/4W H.SW IIC_OFF CAP_LIMIT TV_A_MUTE 16 H.SW TP102 NC RX DVD_RESET AV_SW1 FROM/TO IN/OUT KEY_B KEY_A REC_LED T-REC_LED W841 W842 SCL SDA TX RX REMOCON_IN EXT_A_MUTE VCR_A_MUTE EXT_MUTE TV_POWER_H FROM/TO CHROMA/IF Y/C_DATA Y/C_CS Y/C_CLK OSD_R OSD_G OSD_B OSD_Y EXT_A_MUTE TV_POWER_H V.SYNC H_CONTROL AV_SW1 EXT_MUTE R152 REMOCON_IN H.SYNC SDA SCL VCR_POWER_H PROTECT IIC_OFF EMERGENCY 1B
53
54
VCR.A.MUTE FSCLPF TV_POWER_ON-H VM_OSD_SW CYL_SPEED_UP BLK DEGAUSS R G B CAP_F/R CYL_FG/PG H_CTL FGF 98:C_ROTARY 99:H.AMP.SW1 100:COMP 76:CO CHROMA_POWER_ON_H 77: NC VCR_POWER_ON-H V.REC.START-H REC/OTR_LED SYSCON/TIMER/SERVO IC IC101 OEC8078A 51: VDD2 52: AFCC 25:RESET 24:DUMMY.V.SYNC
IIC_OFF CAP_LIMIT TV_MUTE TUNER_H SCL SDA TX RX TV/DVD_LED Y/C_DATA Y/C_CS Y/C_CLK RENT_H EXT_A_MUTE FF/REW_L AV_SW1 EXT_MUTE REMOCON IN REEL-S REEL-T TAB_SW
22
2.2K
AFCLPF
H.SW
23
0.0022 B
R118 1 F 2.6
52
24
C116
C123 2.5
51
25
5.1
5.0 0.1 3.5 5.0 3.6 0 R140 4.7K R143 0 4.8 4.8 0 0 0 NC 5.0 0.1 5.0 0 0 4.9 0 0.4 5.0 2.4 2.4 0 5.0 W806 REEL-S REEL-T 0 5.1 0 AV_SW Q116 KTC3875S_Y_RTK NC R107 4.7K S101Y
C154
56
55
57
19
20
21
62
C110 OSDB
5
0.001 B C107 D101 LTE-3271T-012A-O BOT SENSOR 5.0 Q101 ST-304L 0 0.001 B C101 EOT SENSOR Q103 ST-304L 5.0
0.0047 B CAP_F/R CYL_FG/PG R108 1K C109 EOT BOT 270 1/10W R103_1 R106 C113 1K 25V 10 KA 0.1 B C111 C117 0.01 B CTL+ 0.001 B R110 C118 10K C122 270K R105 0.0039 B C119 25V 10 KA 17 H_CONTROL
63
13
14
OSDG
61
15
OSDR
60
16
DEGAUSS_H
59
17
OSD_Y
2.2M 1/4W
58
18
CYL_DRIVE
R114
4.7K
65
64
66
67
68
69
6.3V 100 KA
70
C102
71
0 2.5
AVSS CTLA
2.5
VRI
2.5
VRO
3.3
10
11
12
73
EMERGENCY
MSSEN_B
MSSEN_A
LDM_CTL
HIFI_ENV
ENV.DET
KEY_A
BOT
CTL-
R116 560
76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 2.5 0 2.6 0.1 5.1 5.1 4.9 4.9 0 2.6 2.4 0 3.4 3.6 0 0 5.0 0 0.1 0 0 0 3.5 4.9 0 NC
W845 0.027 B C143
C164
TAB SW SW101
EOT
75
CTL(-)
AFT
4.9
560
2.4
KEY_B
CENT_LED_CTL
CTL(+)
PROTECT
74
POWER_FAIL
2.4
T-REC_LED
R115
DVD_RESET
ST_SELECT
R101
72
22K
270K
10V 33 KA 5.0
AVDD
R171 22P CH 1K R166 6.3V 220 YK C146 5.1 R119 2.2K 10K D106 POWER_FAIL 5.1 4.4 MTZJ15B BUFFER Q114 KTA1504S_Y_RTK R165 4.7K HIFI_ENV HIFI_H.SW VCR_A_MUTE SDA SCL ST_SELECT
C120
16V 22 KA
R128
VCR_POWER_H
10K 1/4W
47 YK
FROM/TO CAPSTAN DD UNIT C103 CP101 TMC-J12P-B2 1 2 3 4 5 6 7 8 9 CAP FG CAP VCO VCC CAP.M F/R I LIMIT MOTOR GND GND LD/CY VCO
0 SW Q106 KRC103SRTK 0
4.9
C104
R124
1K 1/2W
10K
R137 C144 0.1 B V.REC_ST_H H.AMP_SW1 DVD_RESET C_ROTARY PROTECT 4.7K COMP
EMERGENCY
MS_SEN-B
MS_SEN-A
ST_SELECT
0 5.0 0
T-REC_LED
ENV_DET
HIFI_ENV
REC_LED
LDM_CTL
TAB_SW
KEY_A
KEY_B
W883
EOT
SW Q110 KRC102SRTK
16V
BOT
AFT
FROM/TO SOUND AMP/SURROUND TV_POWER_H TV_A_MUTE OSD_R SCL SDA FROM/TO DIGITAL COMB FILTER COMB_GND AV_SW1 AV_SW2 SDA SCL AFT FROM/TO TV POWER GND DEGAUSS_H POWER_FAIL MOTOR_GND
R104 3.3K
BACKUP+5V RESET
C112
AT+5V 47K 1/4W 120 1/4W R123 R133 470 YK REEL SENSOR Q108 RPI-303 MTZJ5.6B D103 0 1 2 2.4 27K 1SS133 D102 C141 NC 5 NC R125 0 NC 4 0 SYSTEM RESET IC IC103 PST3231NR
R122
0.1
10 11 12
47K
NC
C106
6.8K
5.1 3
R136
1.2
6.3V
OUT 1 5.2
IN 2 5.1
GND 3 0
R.SIGNAL G.SIGNAL B.SIGNAL RECORD LUMINANCE SIGNAL CYLINDER APC SIGNAL CAPSTAN AFC SIGNAL RECORD COLOR SIGNAL
A B
0.001 CH R113
0.001 CH
R109
25V 47 YK
33K C115
C124
33K
C136
0.1 B
0.9
1.4
0.5
5.1
5.1
D105
4 1.4
C139
1SS133
PCB010 DME034
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
C1511 27P CH C1506 0.1 B C1518 6.3V 470 YK TO Hi-Fi/DEMODULATOR W820 P.CON+5V
C1505
0.01 B
0.01 B C1507
0.01 B
TUNER_AUDIO
C1509
7
C1519 0.1 B
1 AVSS
2 VRB
2.4
3 VRT
3.0
4 ADIN
2.6
5 BIAS1
2.6
6 TEST
7 KILLER
8 DVDD
BIAS2
BIAS3
R1510
CKIN
AVDD
VFIL
DVSS
YOUT
COUT
100P CH
R1506
820 C1515
1.9
5.4
3.8
1.4
4.2
3.6
2.2
2.5
5.4
16
15
14
13
12
11
10
27K
2.5
6
R1512 39P CH
180P CH
R1507
C1513
R1511
C1523
24K
560
1K
R1501
180
W908
10uH 0305
5
L1501
L1504 150uH 16V 220 YK C1530 C1528 0.1 B C1516 16V 47 KA R1502 6.8K 5.0 BUFFER Q1501 KTC3875S_Y_RTK R1505 R1503 100 3.3K 56P CH L1502_1 15uH C1517 120P CH C1514 0.01 B 4.4 2.1 R1520 120 AV SW IC IC1502 MM1501XNRE C1531 1B 4.7 Vin1 GND Vin2 SW1 V OUT Vcc 0 4.9 R1504 4 3 1K 1B C1525 5 2 6 1 4.4 4.2 7.8 R1509 1K AV_SW1 SW_C L1505 R1517 100uH 2.7K P.CON+8V
TUNER_VIDEO P.CON+8V_B
C1502 0.1 B
1.7 1.1
R1508 1.2K
FROM/TO DEFLECTION
C1501
R1518 1K
115-V-KA35ARB
19
10 CLOCK
11 DATA
16 NC
9 NC
8 NC
7 NC
6 NC
5 NC
4 NC
2 NC
1 NC
3
21
+B
C1538 1
18
VIDEO OUT SW IC IC1505 MM1504XNRE 1.0 4.4 Vin1 SW1 6 1 0 GND Vin2 5 1.8 Vcc 4 3 6dB V OUT 2.1 2 R1519 390 1/4W C1534 25V 10 KA
AV SW IC IC1504 MM1501XNRE 8.0 0 5 8.0 4 Vin1 GND Vin2 SW1 V OUT Vcc 5.0 7.3 2 AV_SW2
AV_SW1 AV_SW2 SDA SCL AFT FROM REGULATOR 12.5 3 16V 100 YK C1535 B C1536 L1506 100uH P.CON+12V AT+30V P.CON+5V P.CON+12V P.CON+8V
0 NC 2.1
3.9
31.5
4.2
0 NC 4.8
1.4
NC
NC
NC
NC
C1532 0.001 B C006 W829 C004 0.1 F C005 6.3V 1000 YK R1515 1K 1K 1/4W 47P CH
0.1
31
W837
NC
NC
0 NC 0 NC
7.8
W815
FRONT_V_IN
C001 0.1 F
R1516
C1537
2
W811 L001 100uH 32 TUNER_VIDEO
P.CON+8V_B
W863
TUNER_AUDIO
DVD_VIDEO
SDA
AFT
P.CON+5V
REAR_V_IN
JACK_OUT
AT+30V
SCL
AV_SW1
AUX_V[F/R]
Y/C_VIDEO
PCB010 DME034
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
RECORD LUMINANCE SIGNAL RECORD COLOR SIGNAL PLAYBACK COLOR SIGNAL PLAYBACK LUMINANCE SIGNAL TUNER VIDEO SIGNAL
G H
FROM/TO TV POWER
8
P.CON+12V MOTOR+12V UNREG+8V UNREG+5V +B GND TO DIGITAL COMB FILTER P.CON+5V P.CON+12V
21DQ09N
D3008
4.7
VCR_POWER_H
P.CON+8V AT+30V
6.3V 1000 YK
C3009
W809
0.1
R3010
9.3
7.8 P.CON+8V SW Q3002 KTC3209_Y R3006 100 1/4W 10V 470 YK C3022
P.CON+8V FROM/TO MICON VCR_POWER_H AT+12V P.CON+5V_C DVD_H P.CON+5V_D OUT IC IC3001 KIA278R05PI P.CON+9V_D OUT IC IC3002 KIA278R09PI AT+5V BACKUP+5V P.CON+5V_A
18
1W 8.4
8.5VREG
5
6.4
IN 1
OUT 2 5.4
SW 4
IN 1 6.4
OUT 2 5.3
SW 4
OUT 2
GND
R3009 R3008 W913 220 1/4W R3017 330 1/4W 6.3V 470 YK C3025
21DQ09N
D3011
R3011
R3018
C3027
0.1 B
C3024
10
0.1
10
C3028
TO SOUND AMP/SURROUND
18
P.CON+8V
4
L3001 10uHTSL0808 220 +-1% 4.7 4.0 4.3
P.CON+5V FROM/TO CHROMA/IF DVD+3.8V BUFFER Q3001 KTC3875S_Y_RTK R3007 DVD_H 4.6 SW Q3008 KRA101SRTK 5.3 R3026 50V 10 YK 330 1K 220 R3019 R3025 0 5.4 0 4.9 P.CON+5V_A P.CON+12V TO Hi-Fi/DEMODULATOR 15K C3013 50V 1 KA P.CON+5V
35V 22 YK
100P CH
C3012
C3003
R3012_1
R3031
820 +-1%
220
220
R3013_1
C3008
HS3001 763WAA0184
6.3V
C3014
0.1 B C3023
C3010
D3003
50V 1 KA
MTZJ33B
D3001
MTZJ5.6B
C3007
D3002
50V 1 KA
C3016
C3011
+B
R3005 16V 220 YK R3004 10K 1/4W 4.7K C3006 R3020 100 1/4W 8.0
SW 0 Q3011 KTC3875S_Y_RTK 0
TO DVD IN/OUT R3016 10K VCR_POWER_H AT+5V P.CON+12V DVD+3.8V P.CON+5V_D P.CON+5V_C P.CON+9V_DH
0.7
12.3 13.0
NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
MOTOR+12V GND MOTOR_GND D1723 W903 FROM/TO IN/OUT 160V 220 ED C1720_2 SOUND_GND GND 56K 1/2W R1725 FROM/TO Hi-Fi/DEMODULATOR GND FROM/TO DIGITAL COMB FILTER W888 21.5 MTZJ18B D1717 0 7 15.2 6 12 13 14 220.0 4 186.0 186.0 W898 R1720 1W HS1701 763WAA0238 R1717 8.1 330 2W 0.4 0.0027 B C1712 C1724 0 C1713_1 100V 0.047 500V 0.001 B MMTS D1707 RGP15J D1704 RGP15J C1718 0.0033 B D1733 R1724 100 1/4W 25V 10 KA C1715 D1718 1N4937 C1716 1SS133 25V 2200 YK C1733 D1722 1N4937 R1703 W821 100 1/2W 50V 4.7 YK R1727 1K 1/4W NC 168.0 2 P1 1 18 17 P2 3 16 15 8 11 0 14.1 NC 0 D1713 192.0 0 0 W899 25V 1000 YK 18.0 10.4 C1727 C1732 500V 0.0033 B D1730 FE201-6L49 MTZJ2.2B D1712 10V 2200 YK 21DQ09N C1728_1 D1734 21DQ09N GND
CP1707 003P-2100
CP1708 003P-2100
RM11C-EIC
RM11C-EIC
D1705
D1710
R1722
1/2W
W831
1.2 7W
C1705_1
2.2M
1.5M 1/2W
AC120V_60Hz CD1702 09415910 BLADE WIDE R1701 WHITE BLACK CD1703 WHITE CD1704 BLACK
ECQUL
2KV
560P RR
R1718
FE201-6L49 (W029)
C1701
5
L1704 W5T_20X10X10A
FH1701 EYF-52BCY
FH1702 EYF-52BCY
RM11C-EIC
RM11C-EIC
275V
D1706
D1711
2KV 0.0022 B
2KV 0.0022 B
0.22
C1708
C1710 C1714
S817X
FROM/TO REGULATOR +B UNREG+5V MOTOR+12V UNREG+8V P.CON+12V GND FROM/TO DVD IN/OUT GND
6.3A 125V
2KV 820P RR
C1707_1
221.0 D S 0.1
FROM/TO DEFLECTION CP1702 (CP604) B2013H02-8P +B +B NC GND GND GND P.CON+12V H VOLT 1 2 3 4 5 6 7 8 CD604 CU282401
D1709 1SS133 R1714 17.6 4 R1707 C1702 0.01 B D1703 MTZJ2.7B FEED BACK SWITCHING IC IC1702 KIA431A-AT 56K 1/4W 3.9K 6.2 100 1/4W FEED BACK IC1701 PS2561AL1-1-V(W) 1 5.1 2 C1722 B 0.4 3 0.15 1W R1715 150 R1731 390 1/4W
R1716 3.3K
0.022
R1712
4.7K
R1709
R1713
REFERENCE
330
CATHOOLE
R1719
2.7K 1/4W
100
GND1
W848
R1710
D1728
1SS133
ANODE
D1727
1SS133
D1726
CAUTION:
VR1701 METAL
+B ADJ
10K
1SS133
D1724
1SS133
2.5
2.8
C1711
250V 0.0047 KX
MTZJ6.8B
D1721
D1720
1SS133
R1706
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE.
M5T4-10J W585048
MVDT2002A
SERVICE MANUAL
COLOR TELEVISION/VIDEO CASSETTE RECORDER/ DVD VIDEO PLAYER
CAUTION
THIS DIGITAL VIDEO PLAYER EMPLOYS A LASER SYSTEM. TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS SERVICE MANUAL CAREFULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTENANCE, CONTACT AN AUTHORIZED SERVICE LOCATION-SEE SERVICE PROCEDURE. USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE ENCLOSURE. VISIBLE LASER RADIATION MAY BE PRESENT WHEN THE ENCLOSURE IS OPENED. DO NOT STARE INTO BEAM. Location of the required Marking The rating sheet and the safety caution are on the rear of the unit.
A1-1
6. AVOID AN X-RAY
Safety is secured against an X-ray by considering about the cathode-ray tube and the high voltage peripheral circuit, etc. Therefore, when repairing the high voltage peripheral circuit, use the designated parts and make sure not modify the circuit. Repairing except indicates causes rising of high voltage, and it emits an X-ray from the cathoderay tube.
4. PUT PARTS AND WIRES IN THE ORIGINAL POSITION AFTER ASSEMBLING OR WIRING
There are parts which use the insulation material such as a tube or tape for safety, or which are assembled in the condition that these do not contact with the printed board. The inside wiring is designed not to get closer to the pyrogenic parts and high voltage parts. Therefore, put these parts in the original positions.
1. Unplug the plug from the AC outlet. 2. Remove the antenna terminal on TV and turn on the TV. 3. Insulation resistance between the cord plug terminals and the eternal exposure metal [Note 2] should be more than 1M ohm by using the 500V insulation resistance meter [Note 1]. 4. If the insulation resistance is less than 1M ohm, the inspection repair should be required.
[Note 1]
If you have not the 500V insulation resistance meter, use a Tester.
[Note 2]
A1-2
IMPORTANT SAFEGUARDS
1. READ INSTRUCTIONS All the safety and operating instructions should be read before the unit is operated. 2. RETAIN INSTRUCTIONS The safety and operating instructions should be retained for future reference. 3. HEED WARNINGS All warnings on the unit and in the operating instructions should be adhered to. 4. FOLLOW INSTRUCTIONS All operating and use instructions should be followed. 5. CLEANING liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 6. ATTACHMENTS Do not use attachments not recommended by the unit's manufacturer as they may cause hazards. 7. WATER AND MOISTURE Do not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool. PORTABLE CART WARNING (symbol provided by RETAC) 8. ACCESSORIES Do not place this unit on an unstable cart, stand, tripod, bracket, or table. The unit may fall, causing serious injury, and serious damage to the unit. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer. 8A.An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. S3126A 9. VENTILATION Slots and openings in the cabinet and in the back or bottom are provided for ventilation, to ensure reliable operation of the unit, and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the unit on a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heat source. This unit should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. 10. POWER SOURCES This unit should be operated only from the type of power source indicated on the rating plate. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For units intended to operate from battery power, or other sources, refer to the operating instructions. 11. GROUNDING OR POLARIZATION This unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. If your unit is equipped with a 3-wire grounding-type plug, a plug having a third (grounding) pin, this plug will only fit into a grounding-type power outlet. This too, is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug. 12. POWER-CORD PROTECTION Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance. 13. LIGHTNING To protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning and power line surges. 14. POWER LINES An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them might be fatal. 15. OVERLOADING Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock. 16. OBJECT AND LIQUID ENTRY Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit. 17. OUTDOOR ANTENNA GROUNDING If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. 18. SERVICING Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
A1-3
IMPORTANT SAFEGUARDS
(CONTINUED)
19. DAMAGE REQUIRING SERVICE Unplug this unit from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the unit. c. If the unit has been exposed to rain or water. d. If the unit does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to its normal operation. e. If the unit has been dropped or the cabinet has been damaged. f. When the unit exhibits a distinct change in performance, this indicates a need for service. 20. REPLACEMENT PARTS When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original parts. Unauthorized substitutions may result in fire, electric shock or other hazards. 21. SAFETY CHECK Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to determine that the unit is in proper operating condition. 22. WALL OR CEILING MOUNTING The product should be mounted to a wall or ceiling only as recommended by the manufacturer. 23. HEAT The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. 24. DISC TRAY Keep your fingers well clear of the disc tray as it is closing. It may cause serious personal injury. 25. CONNECTING When you connect the product to other equipment, turn off the power and unplug all of the equipment from the wall outlet. Failure to do so may cause an electric shock and serious personal injury. Read the owner's manual of the other equipment carefully and follow the instructions when making any connections. 26. SOUND VOLUME Reduce the volume to the minimum level before you turn on the product. Otherwise, sudden high volume sound may cause hearing or speaker damage. 27. SOUND DISTORTION Do not allow the product output distorted sound for a longtime. It may cause speaker overheating and fire. 28. HEADPHONES When you use the headphones, keep the volume at a moderate level. If you use the headphones continuously with high volume sound, it may cause hearing damage. 29. LASER BEAM Do not look into the opening of the disc tray or ventilation opening of the product to see the source of the laser beam. It may cause sight damage. 30. DISC Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious personal injury and product malfunction. 31. NOTE TO CATV SYSTEM INSTALLER This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. EXAMPLE OF ANTENNA GROUNDING AS PER THE NATIONAL ELECTRICAL CODE
GROUND CLAMP ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) ELECTRIC SERVICE EQUIPMENT NEC-NATIONAL ELECTRICAL CODE S2898A GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H) A1-4
[ Installing the DVD Deck ] Remove all the soldering on the short circuit position after the connection of Pick Up PCB and DVD PCB connector. NOTE Before your operation, please read "PREPARATION OF SERVICING". Use the Lead Free solder. Manual soldering conditions Soldering temperature: 350 5C Soldering time: Within 2 seconds Soldering combination: Sn-3.0Ag-0.5Cu When Soldering/Removing of solder, use the drawing equipment over the Pick Up Unit to keep the Flux smoke from it.
Pick Up PCB
Fig. 1
PREPARATION OF SERVICING
The laser diode used for a pickup head may be destroyed with external static electricity. Moreover, even if it is operating normally after repair when static electricity discharge is received at the time of repair, the life of the product may be shortened. Please perform the following measure against static electricity, be careful of destruction of a laser diode at the time of repair. Place the unit on a workstation equipped to protect against static electricity, such as conductive mat. Soldering iron with ground wire or ceramic type is used. A worker needs to use a ground conductive wrist strap for body.
A1-5
Fig. 1
Fig. 2
Fig. 1
A1-6
Caution: Pb free solder has a higher melting point than standard solder;
Typically the melting point is 86F~104F(30C~40C) higher. Please use a soldering iron with temperature control and adjust it to 650F 20F (350C 10C). In case of using high temperature soldering iron, please be careful not to heat too long.
Pb free solder will tend to splash when heated too high (about 1100F/ 600C). All products with the printed circuit board with PbF printing must be serviced with lead free solder. When soldering or unsoldering, completely remove all of the solder from the pins or solder area, and be sure to heat the soldering points with the lead free solder until it melts sufficiently.
Recommendations
Recommended lead free solder composition is Sn-3.0Ag-0.5Cu.
A1-7
TABLE OF CONTENTS
CAUTION ................................................................................................................................... SERVICING NOTICES ON CHECKING ................................................................................... HOW TO ORDER PARTS ......................................................................................................... IMPORTANT SAFEGUARDS ................................................................................................... WHEN REPLACING DVD DECK .............................................................................................. PREPARATION OF SERVICING .............................................................................................. TAPE REMOVAL METHOD AT NO POWER SUPPLY .......................................................... DISC REMOVAL METHOD AT NO POWER SUPPLY ........................................................... PARENTAL CONTROL-RATING LEVEL ............................................................................. ABOUT LEAD FREE SOLDER (PbF) .................................................................................... TABLE OF CONTENTS .......................................................................................................... GENERAL SPECIFICATIONS .................................................................................................. DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF MECHANICAL PARTS AND P. C. BOARDS ......................................... 2. REMOVAL OF VCR DECK PARTS ................................................................................. 3. REMOVAL OF DVD DECK PARTS ................................................................................. 4. REMOVAL OF ANODE CAP ............................................................................................ 5. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC ............................................. KEY TO ABBREVIATIONS ....................................................................................................... SERVICE MODE LIST ............................................................................................................... PREVENTIVE CHECKS AND SERVICE INTERVALS ........................................................... WHEN REPLACING EEPROM (MEMORY) IC ........................................................................ SERVICING FIXTURES AND TOOLS ...................................................................................... PREPARATION FOR SERVICING ........................................................................................... MECHANICAL ADJUSTMENTS ............................................................................................... ELECTRICAL ADJUSTMENTS ................................................................................................ BLOCK DIAGRAMS DVD ........................................................................................................................................ Y/C/AUDIO/HEAD AMP ......................................................................................................... MICON .................................................................................................................................... IN/OUT .................................................................................................................................... CHROMA/IF ........................................................................................................................... SOUND AMP/SURROUND/DIGITAL COMB/FILTER ........................................................ Hi-Fi/DEMODULATOR ......................................................................................................... DVD IN/OUT .......................................................................................................................... REGULATOR ........................................................................................................................ TV ........................................................................................................................................... PRINTED CIRCUIT BOARDS DVD ........................................................................................................................................ VCR ........................................................................................................................................ DEFLECTION/CRT/OPERATION ......................................................................................... SCHEMATIC DIAGRAMS MPEG/MICON /DSP .............................................................................................................. MEMORY ................................................................................................................................ MOTOR DRIVE ...................................................................................................................... AUDIO/VIDEO ........................................................................................................................ Y/C/AUDIO/HEAD AMP ......................................................................................................... MICON .................................................................................................................................... IN/OUT .................................................................................................................................... CHROMA/IF ........................................................................................................................... SOUND AMP/SURROUND ................................................................................................... Hi-Fi/DEMODULATOR ........................................................................................................... DIGITAL COMB FILTER ........................................................................................................ DVD IN/OUT ........................................................................................................................... REGULATOR ......................................................................................................................... TV POWER ............................................................................................................................. DEFLECTION ......................................................................................................................... CRT/OPERATION .................................................................................................................. INTERCONNECTION DIAGRAM .............................................................................................. WAVEFORMS ............................................................................................................................ MECHANICAL EXPLODED VIEWS ......................................................................................... CHASSIS EXPLODED VIEWS ................................................................................................. DVD DECK EXPLODED VIEW ................................................................................................. MECHANICAL REPLACEMENT PARTS LIST ........................................................................ CHASSIS REPLACEMENT PARTS LIST ................................................................................ DVD DECK REPLACEMENT PARTS LIST ............................................................................. ELECTRICAL REPLACEMENT PARTS LIST ......................................................................... A1-1 A1-2 A1-2 A1-3, A1-4 A1-5 A1-5 A1-6 A1-6 A1-6 A1-7 A2-1 A3-1~A3-6 B1-1, B1-3 B2-1~B2-6 B3-1~B3-4 B4-1 B5-1, B5-2 C1-1, C1-2 C2-1 C3-1, C3-2 C4-1 D1-1 D1-1 D2-1~D2-4 D3-1~D3-6 E-1, E-2 E-3, E-4 E-5, E-6 E-7, E-8 E-9, E-10 E-11, E12 E-13, E-14 E-15, E-16 E-17, E-18 E-19, E-20 F-1, F-2 F-3~F-6 F-7, F-8 G-1, G-2 G-3, G-4 G-5,G-6 G-7, G-8 G-9, G-10 G-11, G-12 G-13, G-14 G-15, G-16 G-17, G-18 G-19, G-20 G-21, G-22 G-23, G-24 G-25, G-26 G-27, G-28 G-29, G-30 G-31, G-32 G-33, G-34 H-1~H-3 I1-1, I1-2 I2-1, I2-2 I3-1 J1-1 J2-1 J3-1 J4-1~J4-3
A2-1
GENERAL SPECIFICATIONS
G-1 TV System CRT CRT Size / Visual Size CRT Type Magnetic Field BV/BH 20 inch / 508mmV Flat + 0.45 G / 0.18 G NTSC 2 Speaker Front 1.8 x 3.9 Inch 8 ohm 1.0W + 1.0W __ VHS Player / Recorder NTSC Yes OVD-7 4 Heads 2 Heads Mono /Yes Yes SP/SLP SP/LP/SLP FF:1'48"/REW:1'48" T-120 SP/LP/SLP=3x,5x/7x,9x/9x,15x Yes 1/10 NTSC DVD, CD-DA, CD-R/RW 120 mm , 80 mm DM3SA 2-20 times / 4 step 2-45 times (DVD) 4-40 times (CD) 2-20 times / 4 step 2-45 times (DVD) 4-40 times (CD) Fwd 1/7 - 1/2 times -Rev --US System M 1 Tuner US(w/CABLE) 2~69, 4A,A-5~A-1, A~I, J~W,W+1~W+84 45.75MHz 41.25MHz 4.5MHz No US-Stereo Yes 1 V p-p/75 ohm ----220 Lines -8.0dBm/50k ohm --0.5 V p-p/75 ohm(DVD) ------
Sound Output G-2 VCR System System Video System Hi-Fi STEREO NTSC PB Deck Heads Video Head
FM Audio Head Audio /Control Erase(Full Track Erase) Tape Rec PAL Speed NTSC Play PAL NTSC Fast Forward / Rewind Time (Approx.) at 25oC with Cassette Forward/Reverse Picture Search Frame Advance Slow Speed Color System Disc Disc Diameter Drive Search speed NTSC or PAL-M
G-3
DVD System
Slow speed Actual Actual G-4 Tuning System Broadcasting System Tuner and Receive CH Intermediate Frequency Preset CH Stereo/Dual TV Sound Tuner Sound Muting Video Signal System Destination CH Coverage Picture(FP) Sound(FS) FP-FS
G-5
Signal
Input Level Output Level S/N Ratio (Weighted) at DVD Mode S/N Ratio (Weighted) at VCR Mode Horizontal Resolution at DVD Mode Horizontal Resolution at VCR(SP)Mode Output Level Input Level Output Level(0dB=0.775Vrms) Output Level(-20dBFs 0dBFs=2.0Vrms) Digital Output Level S/N Ratio at DVD (Weighted) S/N Ratio at VCR (SP)(CCIR Filter:ON) Harmonic Distortion at DVD Mode Harmonic Distortion at VCR(SP) Mode Frequency Response : DVD Mode at DVD
A3-1
GENERAL SPECIFICATIONS
at Video CD at SVCD at CD at SP at LP at SLP -----------120V,60Hz 110 W at 120 V 60 Hz 4 W at 120 V 60 Hz Yes Yes No No UL FCC DHHS DHHS +5 C ~ +40 C o o -20 C ~ +60 C Less than 80% RH Yes Icon Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes
o o
VCR Mode
G-6
Power
Dynamic Range : More than Frequency Response : Wow And Flutter : Less than Channel Separation : More than Harmonic Distortion : Less than AC DC at AC at DC Stand by (at AC) Per Year Power Fuse Safety Circuit IC Protector(Micro Fuse) Dew Sensor Safety Radiation X-Radiation Laser Operation Storage
Protector
G-7
Regulation
Menu Menu Type System Setup Clock Set On/Off Timer Set Auto Clock On/Off Standard Time Daylight Saving Time TV Setup Language Picture SAP Picture Preference Channel Setup TV/CABLE Auto CH Memory Add/ Delete V-chip Setup Tape Setup Timer Rec Set Auto Repeat On/Off G-CODE(or SHOWVIEW or PLUSCODE)No. Entry Clock / Date TV/VCR DVD CH/AV(LINE) Tape Counter(Linear Counter) Tape Speed Sleep Time Stereo/Audio Output Bilingual SAP Control Volume Level Brightness/Contrast/Sharpness/Color Tint Bass/Treble/Balance Manual Tracking Play/Stop/FF/Rew/Rec/OTR/T-Rec/Pause/Eject/Tape In (Symbol Mark) Auto Tracking/Manual Tracking Caption / Text Index Mute Hi-Fi
A3-2
GENERAL SPECIFICATIONS
Repeat Zero Return DEW Menu (DVD) Menu Type Language Menu Subtitle Audio OSD Language(Set up Language) Video E.B.L. (Enhanced Black Level) TV Screen Size(4:3) OSD Display On/Off Picture Mode (Video/Film/Auto) JPEG Interval Screen Saver Audio DRC (Dynamic Range Control) Dialogue (On DRC[TV] / Off DRC[Std]) Surround System Disc/Card Slot Password Lock/ Un Lock Parental Select Files HDMI (480p/1080i/720p) Output Open Close No disc Reading Play Still/Pause Stop Prohibit Mark PBC Step Skip(>>|) Skip(|<<) Random Repeat Slow+ SlowSearch+ SearchJump Resume Title No. Chapter No. Track No. Time Sub Title No. Angle No. Vocal On/Off Audio No. Audio Stereo L/R Zoom Marker No. Program Play Back Surround On/Off Screen Saver MP3 Yes Yes No Yes Icon Yes Yes Yes Yes No Yes No Yes Yes Yes No Yes Yes Yes No No Yes No Yes Yes No No No Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes (CD,MP3) Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes No Yes No Yes (CD,MP3) No Yes Yes Yes Yes Yes(MP3) Yes English French Spanish 1990/1/1 ~ 2081/12/31 8 Program/ 1 Month 6 Hours -
G-11
G-12 G-13
OSD Language Calendar Clock,Timer Timer Events and Timer One Touch Recording Max Time Back-up OTPB Valid Time
A3-3
GENERAL SPECIFICATIONS
Sleep Timer Max Time Step On/Off Timer Program(On Timer / Off Timer) Auto Shut Off No Signal No Operation Timer Back-up (at Power Off Mode) Unit Glow in Dark Remocon Format Custom Code Power Source Voltage(D.C) UM size x pcs Total Keys Keys TV/VCR
DVD Power 1 2 3 4 5 6 7 8 9 0 ChannelChannel+ VolumeVolume+ Display (Call) Sleep Audio Select Mute Index- / SkipIndex+ / Skip+ T-REC Rec/OTR Slow+ Play Stop Rew / SearchF. Fwd / Search+ Pause / Still CM Skip Speed / Return Counter Reset / Angle Zero Return / Subtitle Input Select / Zoom Menu /Set Up Program / Repeat A-B ATR / Top Menu Tracking+ / DVD Menu Tracking- / Play Mode Cancel 3D Surround Cursor Up Cursor Down Cursor Left Cursor Right Enter
G-14
120 10 1 15 5 RC-HH NEC 71-8E 3V UM-4 x 2 pcs 52 Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes
No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No No No No Yes No
Eject Open/Close TV Monitor Closed Caption Quick View / Jump CABLE Position Wide G-15 Features (TV/VCR) Auto Head Cleaning A/E Head VIDEO PLUS+(SHOWVIEW,G-CODE)
A3-4
GENERAL SPECIFICATIONS
Auto Clock Picture Preference Auto CH Memory Forward / Reverse Picture Search Auto Setup Surround Stable Sound Closed Caption TV Auto Shut off Function End Call Index Search SQPB CABLE CM Skip(30sec x 6 Times) Comb Filter (2Lines) VM Circuit TV Monitor Program Extend Choke Coil Energy Star Protect of FBT Leak Circuit Zero Return Power On Memory V-chip USA V-chip CANADA V-chip Auto Stop (Pause, and Resume Stop after 5min.) Video CD Playback SVCD Playback MP3 Playback WMA Playback JPEG Playback Digital Out (Dolby Digital) (MPEG) (PCM) (DTS) Down Mix Out (Dolby Digital) (DTS) TruSurround Screen Saver Closed Caption Audio DAC Copy (Disc to Tape) Owner's Manual Language w/Guarantee Card Remote Control Unit Battery UM size x pcs OEM Brand Rod Antenna Poles Terminal Loop Antenna Terminal U/V Mixer 300 ohm to 75 ohm Antenna Adapter Antenna Change Plug DC Car Cord (Center+) AC Plug Adapter AC Cord AV Cord (2Pin-1Pin) Guarantee Card Registration Card ESP Card Warning Sheet Dew/AHC Caution Sheet Quick Set-up Sheet Circuit Diagram Service Facility List Important Safeguard Information Sheet (Return) Switch Front Power (Tact) Channel Up Yes Yes Yes Yes No No No Yes Yes No Yes No Yes Yes No No Yes No No No No Yes No Yes No Yes No No No No No Yes Yes Yes Yes Yes No No Yes No 192kHz / 24bit No English / Spanish No Yes No No No No No No No No No No No Yes No No No No No No No No Yes Yes
Features (DVD)
G-16
Accessories
G-17
Interface
A3-5
GENERAL SPECIFICATIONS
Channel Down Volume Up Volume Down Play (VCR) Stop / Eject (VCR) F.FWD/Cue (VCR) Rew/Rev (VCR) REC/OTR (VCR) Play (DVD) Stop (DVD) Skip+ /Search+ (DVD) Skip- /Search- (DVD) Open/Close (DVD) Input Select Main Power SW Power REC/OTR T-REC TV/VCR DVD Front Video Input Audio Input Other Terminal Rear Video Input Audio Input Video Output Audio Output Digital Audio Output VHF/UHF Antenna Input AC Inlet Approx. W x D x H (mm) Net (Approx.) Gross (Approx.) Master Carton Content Material Dimensions W x D x H(mm) Description of Origin Gift Box Material Dimensions W x D x H(mm) Description of Origin Drop Test Natural Dropping At Height (cm) Container Stuffing(40' container) Cabinet Front Rear Jack Panel PCB Non-Halogen Demand Eyelet Environmental standard requirement Pb-free Measures for Whisker Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No No Yes(Red) Yes(Red) Yes(Red) No No RCA x 1 RCA x2(L/MONO,R White,Red) HeadPhone (Stereo & Mono, 3.5mm) No No No No Coaxial (DVD Only) F Type No 573 x 485 x 517 27.0kg (59.5lbs) 30.5kg (67.3lbs) No Double / Brown 658 x 575 x 625 Yes 1 Corner / 3 Edges / 6 Surfaces 31 Sets 216 PS 94V0 DECABROM PS 94V0 DECABROM No Yes Green procurement of ORION Phase3(Phase3A) Yes
Indicator
Terminals
G-21
Material
G-22
Environment
A3-6
DISASSEMBLY INSTRUCTIONS
1. REMOVAL OF MECHANICAL PARTS AND P.C. BOARDS
1-1: BACK CABINET (Refer to Fig. 1-1) 1. Remove the 6 screws (1). 2. Remove the 2 screws (2). 3. Remove the Back Cabinet in the direction of arrow.
Front Cabinet Front Cabinet
1-3: TV/DVD/VCR BLOCK (Refer to Fig. 1-3) 1. Remove the 2 screws (1). 2. Disconnect the following connectors: (CP303, CP404 and CP1704). 3. Remove the TV/DVD/VCR Block in the direction of arrow.
(1) (1)
(1)
TV/DVD/VCR Block
(1)
(1)
Fig. 1-3 1-4: VCR DECK (Refer to Fig. 1-4) NOTE Fig. 1-1 Do not remove the cable at the FE Head section. The FE Head may be damaged if you remove the cable by force. 1. 2. 3. 4. 5. 6. 7. 8. 9. Remove the 2 screws (1). Remove the VCR Top. Move the Cassette Holder Ass'y to the back side. Remove the 3 screws (2). Remove the 2 screws (3). Remove the Deck Shield Cover. Remove the screw (4). Remove the FE Head. Disconnect the following connectors: (CP101, CP4501 and CP4502). 10. Remove the VCR Deck in the direction of arrow.
(2) (2)
(1)
1-2: CRT PCB (Refer to Fig. 1-2) CAUTION: BEFORE REMOVING THE ANODE CAP, DISCHARGE ELECTRICITY BECAUSE IT CONTAINS HIGH VOLTAGE. BEFORE ATTEMPTING TO REMOVE OR REPAIR ANY PCB, UNPLUG THE POWER CORD FROM THE AC SOURCE. 1. Remove the Anode Cap. (Refer to REMOVAL OF ANODE CAP) 2. Disconnect the following connectors: (CP603B, CP803 and CP805). 3. Remove the CRT PCB in the direction of arrow.
CRT PCB
(3)
Front Cabinet Deck Shield Cover
(4)
FE Head
(3) (2)
VCR Deck
(1) (1)
VCR Top Bottom Plate
Fig. 1-2
Fig. 1-4
B1-1
DISASSEMBLY INSTRUCTIONS
1-5: VCR PCB (Refer to Fig. 1-5) 1. Remove the 4 screws (1). 2. Remove the screw (2). 3. Remove the AV Jack Shield. 4. Disconnect the following connectors: (CP001, CP602B, CP604, CP2201, CP8001 and CP8002). 5. Remove the VCR PCB in the direction of arrow.
(1) (1) (1)
1-7: DVD PCB/DVD DECK (Refer to Fig. 1-7) 1. Short circuit the position shown in Fig. 1-7 using a soldering iron. If you remove the DVD Deck with no soldering, the Laser may be damaged. 2. Remove the 4 screws (1). 3. Remove the DVD Top in the direction of arrow (A). 4. Remove the 2 screws (2). 5. Remove the DVD PCB in the direction of arrow (B). 6. Disconnect the following connectors: (CP2301, CP2302 and CP2303). 7. Remove the 4 screws (3). 8. Remove the DVD Deck in the direction of arrow (C).
(1)
(1)
(2)
DVD Top
(1) (1)
(A)
(1)
(2)
(2)
Bottom Plate Pick Up PCB
Fig. 1-5 1-6: VCR DECK (Refer to Fig. 1-6) 1. Remove the 4 screws (1). 2. Remove the DVD Block in the direction of arrow (A). 3. Remove the 2 screws (2). 4. Remove the Operation PCB in the direction of arrow (B).
(1) (1) (1)
DVD Block DVD Deck
(B)
(3) (3)
(3)
(3)
Angle Deck (C) Short circuit using a soldering iron.
(1)
(A)
(2) (2)
(B) Operation PCB Bottom Plate
Fig. 1-6
1. Before your operation, please read "PREPARATION OF SERVICING". 2. Use the Lead Free solder. 3. Manual soldering conditions Soldering temperature: 350 5C Soldering time: Within 2 seconds Soldering combination: Sn-3.0Ag-0.5Cu 4. When Soldering/Removing of solder, use the drawing equipment over the Pick Up Unit to keep the Flux smoke away from it. 5. When installing of the DVD Deck, remove all the soldering on the short circuit position after the connection of Pick Up PCB and DVD PCB connector.
B1-2
DISASSEMBLY INSTRUCTIONS
1-8: DEFLECTION PCB (Refer to Fig. 1-8) 1. Remove the 2 screws (1). 2. Remove the 3 screws (2). 3. Remove the Deflection PCB in the direction of arrow.
(1) (2) (1) (2) (2)
Deflection PCB
Bottom Plate
Fig. 1-8
B1-3
DISASSEMBLY INSTRUCTIONS
2. REMOVAL OF VCR DECK PARTS
2-1: TOP BRACKET (Refer to Fig. 2-1) 1. Extend the 2 supports (1). 2. Slide the 2 supports (2) and remove the Top Bracket. NOTE 1. After installation of the Top Bracket, bend the support (1) so that the Top Bracket is fixed.
Top Bracket Flap Lever
2-4: LINK LEVER/FLAP LEVER (Refer to Fig. 2-4) 1. Extend the support (1). 2. Remove the Link Lever. 3. Remove the Flap Lever.
Top Bracket
(2)
Fig. 2-4
(2)
Main Chassis
Fig. 2-1 2-2: CASSETTE HOLDER ASS'Y (Refer to Fig. 2-2) 1. Move the Cassette Holder Ass'y to the front side. 2. Push the Locker R to remove the Cassette Side R. 3. Remove the Cassette Side L.
Cassette Side R Main Chassis Locker R
1. Remove the screw (1). 2. Remove the Loading Motor. 3. Remove the Worm.
Loading Motor
(1)
Fig. 2-5-A
NOTE 1. In case of the Worm installation, check if the value of the Fig. 2-5-B is correct. 2. In case of the Loading Motor installation, hook the wire on the Cassette Opener as shown Fig. 2-5-C. 3. When installing the wires between Capstan DD Unit and Loading Motor, connect them correctly as shown Fig. 2-5-D.
Fig. 2-2 2-3: LINK UNIT (Refer to Fig. 2-3) 1. Set the Link Unit to the Eject position. 2. Unlock the support (1). 3. Remove the (A) side of the Link Unit first, then remove the (B) side.
Main Chassis
19.2 0.1mm
Link Unit
(A)
(1)
Main Chassis
Fig. 2-5-B
Fig. 2-3
B2-1
DISASSEMBLY INSTRUCTIONS
NOTE
Slacken the wire.
1. In case of the Tension Band installation, note the direction of the installation. (Refer to Fig. 2-6-C) 2. In case of the Tension Band installation, install correctly as Fig. 2-6-D. 3. In case of the Tension Connect installation, install as the circled section of Fig. 2-6-E.
Loading Motor
Fig. 2-5-C
Pink Loading Motor Capstan DD Unit L2
L1
White
Fig. 2-6-D 2-6: TENSION ASS'Y (Refer to Fig. 2-6-B) 1. Turn the Pinch Roller Cam clockwise so that the Tension Holder hook is set to the position of Fig. 2-6-A to move the Tension Arm Ass'y. 2. Remove the Tension Spring. 3. Unlock the 2 supports (1) and remove the Tension Band. 4. Unlock the support (2) and remove the Tension Arm Ass'y. 5. Unlock the support (3) and remove the Tension Connect. 6. Float the hook (4) and turn it clockwise then remove the Tension Holder.
Tension Arm Ass'y Tension Connect
Main Chassis
Fig. 2-6-E
2-7: T BRAKE ARM/T BRAKE BAND (Refer to Fig. 2-7-A) 1. Remove the T Brake Spring. 2. Turn the T Brake Arm clockwise and bend the hook section to remove it. 3. Unlock the 2 supports (1) and remove the T Brake Band.
T Brake Band
Fig. 2-6-A
(1) (1)
Tension Connect
(1)
Tension Band
(1) (3)
(2) (4)
Fig. 2-7-A
Fig. 2-6-B
B2-2
DISASSEMBLY INSTRUCTIONS
NOTE 1. In case of the T Brake Band installation, install correctly as Fig. 2-7-B. [OK]
T Brake Band T Brake Arm
NOTE 1. In case of the S Reel and T Reel installation, check if the correct parts are installed. (Refer to Fig. 2-8-B) 2. In case of the Idler Arm Ass'y installation, install correctly as Fig. 2-8-C. And also set it so that the section "B" of Fig. 2-8-A is placed under the Main Chassis tab.
[NG]
T Brake Band
T Brake Arm
Fig. 2-7-B 2-8: S REEL/T REEL/IDLER ARM ASS'Y/IDLER GEAR (Refer to Fig. 2-8-A) 1. Remove the S Reel and T Reel. 2. Remove the 2 Polyslider Washers (1). 3. Remove the Idler Arm Ass'y and Idler Gear. NOTE 1. Take care not to damage the gears of the S Reel and T Reel. 2. The Polyslider Washer may remain on the back of the reel. 3. Take care not to damage the shaft. 4. Do not touch section "A" of S Reel and T Reel. (Use gloves.) (Refer to Fig. 2-8-A) Touching may leave stains on section "A" 5. When you install the reel, clean the shaft and grease it (FG-84M) . (If you do not grease, noise may be heard in FF/REW mode.) 6. After installing the reel, adjust the height of the reel. (Refer to MECHANICAL ADJUSTMENT) [NG]
Idler Arm Ass'y Clutch Gear
Fig. 2-8-B
[OK]
Clutch Gear Idler Arm Ass'y
Fig. 2-8-C 2-9: CASSETTE OPENER/PINCH ROLLER BLOCK/ P5 ARM ASS'Y (Refer to Fig. 2-9-A) 1. Unlock the support (1) and remove the Cassette Opener. 2. Remove the Pinch Roller Block and P5 Arm Ass'y.
(1)
Cassette Opener
Idler Gear Idler Arm Ass'y S Reel (B) P5 Arm Ass'y (A) T Reel Main Chassis Pinch Roller Block
(1)
(A)
(1)
Fig. 2-9-A NOTE 1. Do not touch the Pinch Roller. (Use gloves.) 2. In case of the Pinch Roller Block and the Pinch Roller Cam installation, install correctly as Fig. 2-9-B. Fig. 2-8-A
Pinch Roller Block Can be seen the hole of the Pinch Roller Cam.
P5 Arm Ass'y
Fig. 2-9-B
B2-3
DISASSEMBLY INSTRUCTIONS
2-10: A/C HEAD (Refer to Fig. 2-10-A) 1. 2. 3. 4. Remove the screw (1). Remove the A/C Head Base. Remove the 3 screws (2). Remove the A/C Head and A/C Head Spring. 2-12: CYLINDER UNIT ASS'Y (Refer to Fig. 2-12) 1. Disconnect the following connector: (CD2001). 2. Remove the 3 screws (1). 3. Remove the Cylinder Unit Ass'y. NOTE 1. When you install the Cylinder Unit Ass'y, tighten the screws from (1) to (3) in order while pulling the Ass'y toward the left front direction.
NOTE 1. Do not touch the A/C Head. (Use gloves.) 2. When you install the A/C Head Spring, install as shown in Fig. 2-10-B. 3. When you install the A/C Head, tighten the screw (1) first, then tighten the screw (2), finally tighten the screw (3).
(1) (2) (2) (2) (3) (2)
A/C Head
A/C Head Spring (1) (3) A/C Head Base Screw Torque: 5 0.5kgfcm (2) (1) (1) Screw Torque: 3 0.5kgfcm (1) (1)
Fig. 2-10-A
Fig. 2-12
Remove the Capstan Belt. Remove the screw (1). Remove the Capstan Holder. Remove the 3 screws (2). Remove the Capstan DD Unit.
Fig. 2-10-B
2-11: FE HEAD (RECORDER ONLY) (Refer to Fig. 2-11) 1. Remove the screw (1). 2. Remove the FE Head.
(1)
Capstan Belt
(1)
Capstan Holder Capstan DD Unit
FE Head
Fig. 2-11
Fig. 2-13
B2-4
DISASSEMBLY INSTRUCTIONS
2-14: MAIN CAM/PINCH ROLLER CAM/JOINT GEAR (Refer to Fig. 2-14-A) 1. Remove the E-Ring (1), then remove the Main Cam. 2. Remove the E-Ring (2), then remove the Pinch Roller Cam and Joint Gear.
(1)
Main Cam Main Loading Gear Marker
NOTE 1. When you install the Loading Arm S Unit, Loading Arm T Unit and Main Loading Gear, align each marker. (Refer to Fig. 2-15-B)
Marker
(2)
Pinch Roller Cam
Joint Gear
Fig. 2-15-B Fig. 2-14-A NOTE 1. In case of the Pinch Roller Cam and Main Cam installation, install them as shown in the circled section of Fig. 2-15-B so that the markers meet. (Refer to Fig. 2-14-B) And also can be seen the Main Chassis hole through the Main Cam maker hole. 2-16: CLUTCH ASS'Y/RING SPRING/CLUTCH LEVER/ CLUTCH GEAR (Refer to Fig. 2-16-A) 1. 2. 3. 4. Remove the Polyslider Washer (1). Remove the Clutch Ass'y and Ring Spring. Remove the Clutch Lever. Remove the Coupling Gear, Coupling Spring and Clutch Gear.
(1)
Clutch Ass'y
Ring Spring
Clutch Lever
Fig. 2-14-B 2-15: LOADING GEAR S/T UNIT (Refer to Fig. 2-15-A) 1. Remove the E-Ring (1) and remove the Main Loading Gear. 2. Remove the Main Rod, Tension Lever, Loading Arm S Unit and Loading Arm T Unit.
(1)
Main Rod Main Loading Gear
Fig. 2-16-A
Fig. 2-15-A
B2-5
DISASSEMBLY INSTRUCTIONS
NOTE 1. In case of the Clutch Ass'y installation, install it with inserting the spring of the Clutch Ass'y into the dent of the Coupling Gear. (Refer to Fig. 2-16-B) NOTE 1. Do not touch the roller of Guide Roller. 2. In case of the P4 Cap installation, install it with parallel for "A" and "B" of Fig. 2-17-B. 3. In case of the Cassette Guide Post installation, install correctly as the circled section of Fig. 2-17-C.
"A" "B"
Clutch Ass'y
Coupling Gear
Fig. 2-16-B 2-17: CASSETTE GUIDE POST/INCLINED BASE S/T UNIT/P4 CAP/LED REFLECTOR (Refer to Fig. 2-17-A) 1. Remove the P4 Cap. 2. Unlock the support (1) and remove the Cassette Guide Post. 3. Remove the Inclined Base S/T Unit. 4. Remove the screw (2). 5. Remove the LED Reflector.
Cassette Guide Post
P4 Cap
Cassette Opener
(1)
Inclined Base S Unit
[NG]
Cassette Guide Post Inclined Base T Unit
P4 Cap
Fig. 2-17-C
LED Reflector
(2)_
Fig. 2-17-A
B2-6
DISASSEMBLY INSTRUCTIONS
3. REMOVAL OF DVD DECK PARTS
NOTE 1. Disassemble only the DVD DECK PARTS parts listed here. Minute adjustments are needed if the disassembly is done. If the repair is needed except listed parts, replace the DVD MECHA ASS'Y. 3-1: TRAY (Refer to Fig. 3-1-A) 1. Set the Tray opened. (Refer to the DISC REMOVAL METHOD AT NO POWER SUPPLY) 2. Unlock the 2 supports (1) and remove the Tray.
Main Frame Ass'y (3) Traverse Holder (3) Rack Loading (3)
NOTE 1. In case of the Main Chassis Ass'y, install it from (1) to (4) in order. (Refer to Fig. 3-2-B) 2. In case of the Main Chassis Ass'y installation, hook the wire on the Main Frame Ass'y as shown Fig. 3-2-C.
Main Frame Ass'y (Bottom Side)
(2)
(1)
Tray
(1)
(4) (4)
Fig. 3-1-A NOTE 1. In case of the Tray installation, install them as the circled section of Fig. 3-1-B so that the each markers are met.
Main Frame Ass'y
Check Lock
Fig. 3-2-B
Check Hook
Fig. 3-2-C
3-3: LOADING MOTOR PCB ASS'Y/ LOADING BELT (Refer to Fig. 3-3-A) 1. 2. 3. 4. 5. Remove the Loading Belt. Remove the screw (1). Remove the 2 screws (2). Remove the Loading Motor PCB Ass'y. Remove the Pulley Gear.
Loading Belt
Tray
Fig. 3-1-B 3-2: MAIN CHASSIS ASS'Y (Refer to Fig. 3-2-A) 1. 2. 3. 4. Remove the screw (1). Unlock the 2 supports (2). Remove the Insulator (R) from the Main Frame Ass'y. Remove the Main Chassis Ass'y.
(1) (2) (2)
Main Frame Ass'y
(2) (2)
(1)
Screw Torque: 2.5 0.3kgfcm (Screw (1)) Screw Torque: 1.0 0.3kgfcm (Screw (2)) Insulator (R) Main Chassis Ass'y
Fig. 3-3-A
DISASSEMBLY INSTRUCTIONS
NOTE 1. In case of the Pulley Motor installation, check if the value of the Fig. 3-3-B is correct. 2. When installing the Loading Motor PCB Ass'y, install it correctly as Fig. 3-3-C. 3. In case of the Loading Motor PCB Ass'y installation, hook the wire on the Main Frame Ass'y as shown Fig. 3-3-C. 3-5: CLAMPER ASS'Y (Refer to Fig. 3-5-A) 1. Press the Clamper and rotate the Clamper Plate clockwise, then unlock the 3 supports (1). 2. Remove the Clamper Plate, Clamper Magnet and Clamper.
Clamper Plate Clamper Magnet
Pulley Motor
7.0 0.1mm
Main Frame
Loading Motor
(1)
Safety surface for pressing of the insert.
(1) (1)
Clamper
Fig. 2-5-A
Fig. 3-3-B NOTE 1. In case of the Clamper Ass'y installation, install correctly as Fig. 3-5-B.
Clamper Plate
Clamper
No gap
Fig. 3-5-B
Check Hook Loading Motor PCB Ass'y
Fig. 3-3-C 3-6: TRAVERSE HOLDER/INSULATOR (F)/INSULATOR (R) (Refer to Fig. 3-6-A) 1. Remove the Traverse Holder. 2. Remove the 2 Insulator (F). 3. Remove the Insulator (R).
Insulator (R) Main Chassis Ass'y
3-4: RACK LOADING/MAIN GEAR/PULLEY GEAR (Refer to Fig. 3-4-A) 1. Press down the catcher (1) and slide the Rack Loading. 2. Unlock the support (2) and remove the Pulley Gear. 3. Remove the Main Gear.
Rack Loading
(2)
(1)
Fig. 3-4-A NOTE 1. In case of the Rack Loading installation, do not mesh it to the Main Gear as shown the Fig. 3-4-B.
Rack Loading Check Hook
Fig. 3-6-A NOTE 1. In case of the Insulator (F) installation, install correctly as Fig. 3-6-B. 2. In case of the Insulator (R) installation, install correctly as Fig. 3-6-C.
Insulator (F)
Traverse Holder
Main Gear
Fig. 3-6-B
DISASSEMBLY INSTRUCTIONS
Insulator (R) Main Chassis Ass'y (Top Side) Motor Gear 6.0 0.2mm
Feed Motor
Fig. 3-6-C 3-7: RACK FEED ASS'Y/SWITCH PCB ASS'Y/FEED MOTOR (Refer to Fig. 3-7-A) 1. 2. 3. 4. 5. 6. 7. Remove the screw (1). Remove the Rack Feed Ass'y. Remove the screw (2). Remove the Switch PCB Ass'y. Remove the 2 screw (3). Remove the Feed Motor. Remove the Motor Gear.
(1) (2)
Rack Feed Ass'y Install wire from (1) to (4) in order. Safety surface for pressing of the insert.
Fig. 3-7-C
(3)
(3)
Fig. 3-7-D
Main Chassis Ass'y (Bottom Side) Check Hook Check Hook Check Hook
Motor Gear Main Chassis Ass'y Feed Motor Screw Screw Screw Screw Torque: Torque: Torque: Torque: 5.0 3.0 1.0 3.5 0.3kgfcm 0.3kgfcm 0.3kgfcm 0.3kgfcm (Screw (Screw (Screw (Screw (1)) (2)) (3)) (4))
Fig. 3-7-A
NOTE 1. When pushing the Rack Feed in the direction of the arrow, it should be restored to the original position by the spring force. (Refer to Fig. 3-7-B) 2. In case of the Motor Gear installation, check if the value of the Fig. 3-7-C is correct. 3. When installing the wire of the Switch PCB Ass'y, install it correctly as Fig. 3-7-D. 4. After the assembly of the Main Chassis Ass'y, hook the wire on the Main Chassis Ass'y as shown Fig. 3-7-E.
Check Hook Loosen the wire in the direction of the arrow.
Fig. 3-7-E
Fig. 3-7-B
B3-3
DISASSEMBLY INSTRUCTIONS
3-8: FFC WIRE HANDLING 1. When installing the FFC, fold it correctly and install it as shown from Fig. 3-8-A to Fig. 3-8-C. NOTE 1. Do not make the folding lines except the specified positions for the FFC. [ 24 pin FFC ]
Pick Up Side
Printing Surface
54 1mm
Fold it by 90
Fold
Printing Surface
43 1mm
(3)
Reinforcement Plate
(4) (2)
Fold Printing Surface 10 1mm Printing Surface Fold
Fig. 3-8-B
[ 5 pin FFC ]
(1)
Reinforcement Plate
(3)
Reinforcement Plate
(4) (2)
Fold
Printing Surface
Fig. 3-8-C
B3-4
DISASSEMBLY INSTRUCTIONS
4. REMOVAL OF ANODE CAP
Read the following NOTED items before starting work. 3. After one side is removed, pull in the opposite direction to remove the other. NOTE Take care not to damage the Rubber Cap. INSTALLATION 1. Clean the spot where the cap was located with a small amount of alcohol. (Refer to Fig. 4-3.)
* *
After turning the power off there might still be a potential voltage that is very dangerous. When removing the Anode Cap, make sure to discharge the Anode Cap's potential voltage. Do not use pliers to loosen or tighten the Anode Cap terminal, this may cause the spring to be damaged.
REMOVAL 1. Follow the steps as follows to discharge the Anode Cap. (Refer to Fig. 4-1.) Connect one end of an Alligator Clip to the metal part of a flat-blade screwdriver and the other end to ground. While holding the plastic part of the insulated screwdriver, touch the support of the Anode with the tip of the screwdriver. A cracking noise will be heard as the voltage is discharged. Location of Anode Cap
Fig. 4-3 GND on the CRT NOTE Confirm that there is no dirt, dust, etc. at the spot where the cap was located. 2. Arrange the wire of the Anode Cap and make sure the wire is not twisted. 3. Turn over the Rubber Cap. (Refer to Fig. 4-4.)
Screwdriver
CRT
GND on the CRT Fig. 4-1 2. Flip up the sides of the Rubber Cap in the direction of the arrow and remove one side of the support. (Refer to Fig. 4-2.) Rubber Cap Fig. 4-4 4. Insert one end of the Anode Support into the anode button, then the other as shown in Fig. 4-5.
5. Confirm that the Support is securely connected. 6. Put on the Rubber Cap without moving any parts.
B4-1
DISASSEMBLY INSTRUCTIONS
5. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC
REMOVAL 1. Put Masking Tape (cotton tape) around the Flat Package IC to protect other parts from any damage. (Refer to Fig. 5-1.) NOTE Masking is carried out on all the parts located within 10 mm distance from IC leads.
Blower type IC desoldering machine
3. When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using a tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 5-3.) NOTE Some ICs on the PCB are affixed with glue, so be careful not to break or damage the foil of each IC leads or solder lands under the IC when removing it.
IC
Tweezers
Fig. 5-1
IC
2. Heat the IC leads using a blower type IC desoldering machine. (Refer to Fig. 5-2.) NOTE Do not rotate or move the IC back and forth until IC can move back and forth easily after desoldering the leads completely.
Fig. 5-3 4. Peel off the Masking Tape. 5. Absorb the solder left on the pattern using the Braided Shield Wire. (Refer to Fig. 5-4.) NOTE Do not move the Braided Shield Wire in the vertical direction towards the IC pattern.
Soldering Iron
IC pattern IC
Fig. 5-4
Fig. 5-2
B5-1
DISASSEMBLY INSTRUCTIONS
INSTALLATION 1. Take care of the polarity of new IC and then install the new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily. (Refer to Fig. 5-5.) 4. When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thintip Soldering Iron. (Refer to Fig. 5-8.)
IC
Soldering Iron
Fig. 5-8 5. Finally, confirm the soldering status on four sides of the IC using a magnifying glass. Confirm that no abnormality is found on the soldering position and installation position of the parts around the IC. If some abnormality is found, correct by resoldering. NOTE When the IC leads are bent during soldering and/or repairing, do not repair the bending of leads. If the bending of leads are repaired, the pattern may be damaged. So, be always sure to replace the IC in this case.
Solder temporarily
Solder temporarily
Fig. 5-5 2. Supply the solder from the upper position of IC leads sliding to the lower position of the IC leads. (Refer to Fig. 5-6.)
Solder
Soldering Iron
IC
Fig. 5-6 3. Absorb the solder left on the lead using the Braided Shield Wire. (Refer to Fig. 5-7.) NOTE Do not absorb the solder to excess.
Soldering Iron IC
Fig. 5-7
B5-2
KEY TO ABBREVIATIONS
A A/C ACC AE AFC AFT AFT DET AGC AMP ANT A.PB APC ASSY AT AUTO A/V B BGP BOT BPF BRAKE SOL BUFF B/W C C CASE CAP CARR CH CLK CLOCK (SY-SE) COMB CONV CPM CTL CYL CYL-M CYL SENS D DATA (SY-CE) dB DC DD Unit DEMOD DET DEV E E EF EMPH ENC ENV EOT EQ EXT F F FBC FE FF FG FL SW FM FSC FWD G GEN GND H H.P.F : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : Audio/Control Automatic Color Control Audio Erase Automatic Frequency Control Automatic Fine Tuning Automatic Fine Tuning Detect Automatic Gain Control Amplifier Antenna Audio Playback Automatic Phase Control Assembly All Time Automatic Audio/Video Burst Gate Pulse Beginning of Tape Bandpass Filter Brake Solenoid Buffer Black and White Capacitance, Collector Cassette Capstan Carrier Channel Clock Clock (Syscon to Servo) Combination, Comb Filter Converter Capstan Motor Control Cylinder Cylinder-Motor Cylinder-Sensor Data (Syscon to Servo) Decibel Direct Current Direct Drive Motor Unit Demodulator Detector Deviation Emitter Emitter Follower Emphasis Encoder Envelope End of Tape Equalizer External Fuse Feed Back Clamp Full Erase Fast Forward, Flipflop Frequency Generator Front Loading Switch Frequency Modulation Frequency Sub Carrier Forward Generator Ground High Pass Filter I H.SW Hz IC IF IND INV KIL L LED LIMIT AMP LM, LDM LP L.P.F LUMI. M MAX MINI MIX MM MOD MPX MS SW NC NR OSC OPE PB PB CTL PB-C PB-Y PCB P. CON PD PG P-P R REC REC-C REC-Y REEL BRK REEL S REF REG REW REV, RVS RF RMC RY S. CLK S. COM S. DATA SEG SEL SENS SER SI SIF SO SOL SP STB SW : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : Head Switch Hertz Integrated Circuit Intermediate Frequency Indicator Inverter Killer Left Light Emitting Diode Limiter Amplifier Loading Motor Long Play Low Pass Filter Luminance Motor Maximum Minimum Mixer, mixing Monostable Multivibrator Modulator, Modulation Multiplexer, Multiplex Mecha State Switch Non Connection Noise Reduction Oscillator Operation Playback Playback Control Playback-Chrominance Playback-Luminance Printed Circuit Board Power Control Phase Detector Pulse Generator Peak-to Peak Right Recording Recording-Chrominance Recording-Luminance Reel Brake Reel Sensor Reference Regulated, Regulator Rewind Reverse Radio Frequency Remote Control Relay Serial Clock Sensor Common Serial Data Segment Select, Selector Sensor Search Mode Serial Input Sound Intermediate Frequency Serial Output Solenoid Standard Play Serial Strobe Switch
K L
N O P
C1-1
KEY TO ABBREVIATIONS
S SYNC SYNC SEP T TR TRAC TRICK PB TP U UNREG V V VCO VIF VP V.PB VR V.REC VSF VSR VSS V-SYNC VT X XTAL Y Y/C : : : : : : : : : : : : : : : : : : : : : Synchronization Sync Separator, Separation Transistor Tracking Trick Playback Test Point Unregulated Volt Voltage Controlled Oscillator Video Intermediate Frequency Vertical Pulse, Voltage Display Video Playback Variable Resistor Video Recording Visual Search Fast Forward Visual Search Rewind Voltage Super Source Vertical-Synchronization Voltage Tuning Crystal Luminance/Chrominance
C1-2
3 4
2 2
REC/OTR
STOP (DVD)
Set Key
Set Key
Operations The BOT, EOT, and the Reel Sensor do not work and the VCR deck can be operated without a cassette tape. Refer to the "PREPARATION FOR SERVICING" Operations
FF
Method Press the ATR button on the remote control for more than 2 seconds during PLAY.
Adjust Tracking to the center position. Refer to the "MECHANICAL ADJUSTMENT" (GUIDE ROLLER) and "ELECTRICAL ADJUSTMENT" (PG SHIFTER).
C2-1
Initial setting content of MEMORY IC. POWER ON total hours. PLAY/REC total hours.
(16 x 16 x 16 x thousands digit value) + (16 x 16 x hundreds digit value) + (16 x tens digit value) + (ones digit value)
C3-1
C3-2
1. Enter DATA SET mode by setting VOLUME to minimum. 2. Press both VOL. DOWN button on the set and the Channel button (6) on the remote control for more than 2 seconds. ADDRESS and DATA should appear as FIG 1.
ADDRESS DATA
INIT
00
2F
Fig. 1 3. ADDRESS is now selected and should "blink". Using the UP or DOWN button on the remote, step through the ADDRESS until required ADDRESS to be changed is reached. 4. Press ENTER to select DATA. When DATA is selected, it will "blink". 5. Again, step through the DATA using UP or DOWN button until required DATA value has been selected. 6. Pressing ENTER will take you back to ADDRESS for further selection if necessary. 7. Repeat steps 3 to 6 until all data has been checked. 8. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input. After the data input, set to the initializing of shipping. 9. Turn POWER on. 10. Press both VOL. DOWN button on the set and the Channel button (1) on the remote control for more than 2 seconds. 11. After the finishing of the initializing of shipping, the unit will turn off automatically. The unit will now have the correct DATA for the new MEMORY IC.
C4-1
JG185 Tentelometer
Ref. No. JG001 JG001A JG001Q JG001T JG001B JG001I JG001P JG001S JG002B JG002E JG002F JG005 JG153 JG022 JG024A JG100A JG185
Part No. APJG001000 APJG001A00 APJG001Q00 APJG001T00 APJG001B00 APJG001I00 APJG001P00 APJG001S00 APJG002B00 APJG002E00 APJG002F00 APJG005000 APJG153000 APJG022000 APJG024A00 APJG100A00 APJG185000
Parts Name VHS Alignment Tape VHS Alignment Tape VHS Alignment Tape VHS Alignment Tape VHS Alignment Tape VHS Alignment Tape VHS Alignment Tape VHS Alignment Tape Adapter Dial Torque Gauge (10~90gfcm) Dial Torque Gauge (60~600gfcm) Post Adjustment Screwdriver X Value Adjustment Screwdriver Master Plane Reel Disk Height Adjustment Jig Torque Tape (VHT-063) Tentelometer
Remarks Monoscope, 6KHz (For 2 heads model) Color Bar, 1KHz (For 2 heads model) Hi-Fi Audio (For 2 heads model) X Value Adjustment (For 2 heads model) Monoscope, 6KHz (For 4 heads model) Color Bar, 1KHz (For 4 heads model) Hi-Fi Audio (For 4 heads model) X Value Adjustment (For 4 heads model) VSR Torque, Brake Torque (S Reel/T Reel Ass'y) Brake Torque (T Reel Ass'y) VSR Torque, Brake Torque (S Reel) Guide Roller Adjustment X Value Adjustment Reel Disk Height Adjustment Reel Disk Height Adjustment Playback Torque, Back Tension Torque During Playback Confirmation of Tape Tension on Playback
D1-1
MECHANICAL ADJUSTMENTS
1. CONFIRMATION AND ADJUSTMENT
Read the following NOTES before starting work. Place an object which weighs between 450g~500g on the Cassette Tape to keep it steady when you want to make the tape run without the Cassette Holder. (Do not place an object which weighs over 500g.) 1-2: CONFIRMATION AND ADJUSTMENT OF TENSION POST POSITION 1. Set to the PLAY mode. 2. Adjust the adjusting section for the Tension Arm position so that the Tension Arm top is within the standard line of Main Chassis. 3. While turning the S Reel clockwise, confirm that the edge of the Tension Arm is located in the position described above.
Standard line of Main Chassis
1-1: CONFIRMATION AND ADJUSTMENT OF REEL DISK HEIGHT 1. Turn on the power and set to the STOP mode. 2. Set the master plane (JG022) and reel disk height adjustment jig (JG024A) on the mechanism framework, taking care not to scratch the drum, as shown in Fig. 1-1-A. 3. While turning the reel and confirm the following points. Check if the surface A of reel disk is lower than the surface B of reel disk height adjustment jig (JG024A) and is higher than the surface C. If it is not passed, place the height adjustment washers and adjust to 10(+2, -0)mm. 4. Adjust the other reel in the same way.
Master Plane (JG022)
Tension Arm
Fig. 1-2-A
Tension Band
The Tension Arm top will move to the inside direction of the Main Chassis. Bend
The Tension Arm top will move to the outside direction of the Main Chassis.
Fig. 1-2-B
Fig. 1-1-A
Reel Disk Height Adjustment Jig (JG024A) (B)
1-3: CONFIRMATION OF PLAYBACK TORQUE AND BACK TENSION TORQUE DURING PLAYBACK 1. Load a video tape (T-120) recorded in standard speed mode. Set the unit to the PLAY mode. 2. Install the tentelometer (JG185) as shown in Fig. 1-3. Confirm that the meter indicates 20 2gf in the beginning of playback. USING A CASSETTE TYPE TORQUE TAPE (JG100A) 1. After confirmation and adjustment of Tension Post position (Refer to item 1-2), load the cassette type torque tape (JG100A) and set to the PLAY mode. 2. Confirm that the right meter of the torque tape indicates 50~90gfcm during playback in SP mode. 3. Confirm that the left meter of the torque tape indicates 25~40gfcm during playback in SP mode.
Tentelometer (JG185)
Reel Disk
10(+0.2, -0)mm
(C)
Fig. 1-1-B
Video Tape
P1 Post
Guide Roller
Fig. 1-3
D2-1
MECHANICAL ADJUSTMENTS
1-4: CONFIRMATION OF VSR TORQUE 1. Install the Torque Gauge (JG002F) and Adapter (JG002B) on the S Reel. Set to the Picture Search (Rewind) mode. (Refer to Fig.1-4-B) 2. Then, confirm that it indicates 120~180gfcm. NOTE Install the Torque Gauge on the reel disk firmly. Press the REW button to turn the reel disk. 1-5: CONFIRMATION OF REEL BRAKE TORQUE (S Reel Brake) (Refer to Fig. 1-4-B) 1. Once set to the Fast Forward mode then set to the Stop mode. While, unplug the AC cord when the Pinch Roller Block is on the position of Fig. 1-4-A. 2. Move the Idler Assy from the S Reel. 3. Install the Torque Gauge (JG002F) and Adapter (JG002B) on the S Reel. Turn the Torque Gauge (JG002F) clockwise. 4. Then, confirm that it indicates 60~100gf cm. (T Reel Brake) (Refer to Fig. 1-4-B) 1. Once set to the Fast Forward mode then set to the Stop mode. While, unplug the AC cord when the Pinch Roller Block is on the position of Fig. 1-4-A. 2. Move the Idler Assy from the T Reel. 3. Install the Torque Gauge (JG002E) and Adapter (JG002B) on the T reel. Turn the Torque Gauge (JG002E) counterclockwise. 4. Then, confirm that it indicates 30~50gfcm.
The position at FF mode. Pinch Roller Block Stop at this position.
NOTE If the torque is out of the range, replace the following parts. Check item 1-4 1-5 Replacement Part Idler Assy/Clutch Assy S Reel side: S Reel/Tension Band/Tension Connect/Tension Arm Assy T Reel side: T Reel/T Brake Band//T Brake Spring/T Brake Arm
Fig. 1-4-A
Fig. 2-1-A
Entrance S Reel Max A B Max Exit
T Reel
Fig. 1-4-B
A : B >3 : 2
Fig. 2-1-B
D2-2
MECHANICAL ADJUSTMENTS
2-2: CONFIRMATION AND ADJUSTMENT OF AUDIO/ CONTROL HEAD When the Tape Running Mechanism does not work well, adjust the following items. 1. Playback the VHS Alignment Tape (JG001 or JG001B). (Refer to SERVICING FIXTURE AND TOOLS) 2. Confirm that the reflected picture of stamp mark is appeared on the tape prior to P4 Post as shown in Fig. 2-2-A. a) When the reflected picture is distorted, turn the screw (1) clockwise until the distortion is disappeared. b) When the reflected picture is not distorted, turn the screw (1) counterclockwise until little distortion is appeared, then adjust the a). 3. Turn the screw (2) to set the audio level to maximum. 4. Confirm that the bottom of the Audio/ Control Head and the bottom of the tape is shown in Fig. 2-2-C. c) When the height is not correct, turn the screw (3) to adjust the height. Then, adjust the 1~3 again.
Audio/Control Head Reflected picture of Stamp Mark P4 Cap (1) CH-3 Audio (2) Envelope
2-3: TAPE RUNNING ADJUSTMENT (X VALUE ADJUSTMENT) 1. Confirm and adjust the height of the Reel Disk. (Refer to item 1-1) 2. Confirm and adjust the position of the Tension Post. (Refer to item 1-2) 3. Adjust the Guide Roller. (Refer to item 2-1) 4. Confirm and adjust the Audio/Control Head. (Refer to item 2-2) 5. Connect CH-1 of the oscilloscope to TP102, CH-2 to TP4501 and CH-3 to HOT side of Audio Out Jack. 6. Playback the VHS Alignment Tape (JG001S or JG001T). (Refer to SERVICING FIXTURE AND TOOLS) 7. Press and hold the Tracking-Auto button on the remote control more than 2 seconds to set tracking to center. 8. Set the X Value adjustment driver (JG153) to the (4) of Fig. 2-2-B. Adjust X value so that the envelope waveform output becomes maximum. Check if the relation between Audio and Envelope waveform becomes (1) or (2) of Fig. 2-3.
Fig. 2-3
Stamp Mark
Fig. 2-2-A
2-4: CONFIRM Hi-Fi AUDIO (Hi-Fi model only) 1. Connect CH-1 of the oscilloscope to TP4501 and CH-2 to the Hi-Fi Audio Out Jack. 2. Playback the VHS Alignment Tape (JG001P or JG001Q). Refer to SERVICING FIXTURE AND TOOLS) 3. Press and hold the Tracking-Auto button on the remote control more than 2 seconds to set tracking to center. 4. Press the Tracking Up button and count number of steps which the audio output is changed from Hi-Fi (10KHz) to MONO (6KHz). 5. Press and hold the Tracking-Auto button on the remote control more than 2 seconds to set tracking to center. 6. Press the Tracking Down button and count number of steps which the audio output is changed from Hi-Fi (10KHz) to MONO (6KHz). 7. If the difference are more than 3 steps, set the X Value adjustment driver (JG153) to (4) of Fig. 2-2-B. Change the X Value and adjust it so that the value becomes within 2 steps.
Audio/Control Head
(3)
(1)
(2) (4)
Fig. 2-2-B
0.250.05mm
Fig. 2-2-C
D2-3
MECHANICAL ADJUSTMENTS
3. MECHANISM ADJUSTMENT PARTS LOCATION GUIDE
4 5
6 3
10
1. Tension Connect 2. Tension Arm 3. Guide Roller 4. Audio/Control Head 5. X value adjustment driver hole
6. P4 Post 7. T Brake Spring 8. T Reel 9. S Reel 10. Adjusting section for the Tension Arm position
D2-4
ELECTRICAL ADJUSTMENTS
1. BEFORE MAKING ELECTRICAL ADJUSTMENTS
Read and perform these adjustments when repairing the circuits or replacing electrical parts or PCB assemblies. CAUTION Use an isolation transformer when performing any service on this chassis. Before removing the anode cap, discharge electricity because it contains high voltage. When removing a PCB or related component, after unfastening or changing a wire, be sure to put the wire back in its original position. When you exchange IC and Transistor with a heat sink, apply silicon grease (YG6260M) on the contact section of the heat sink. Before applying new silicon grease, remove all the old silicon grease. (Old grease may cause damages to the IC and Transistor). Prepare the following measurement tools for electrical adjustments. 1. Oscilloscope 2. Digital Voltmeter 3. Multi-sound Generator 4. Pattern Generator On-Screen Display Adjustment 1. Unplug the AC plug for more than 5 seconds to set the clock to the non-setting state. Then, set the volume level to minimum. 2. Press the VOL. DOWN button on the set and the Channel button (9) on the remote control for more than 2 seconds to appear the adjustment mode on the screen as shown in Fig. 1-1.
NO. 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 FUNCTION OSD H OSD C CUT OFF H.POSI H.BLK L H.BLK R V.SIZE V.POSI V.LIN VS.CORR V.COMP R.BIAS G.BIAS B.BIAS R.DRV G.DRV B.DRV BRI CENT NO. 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 FUNCTION BRI MAX BRI MIN CONT CENT CONT MAX CONT MIN COL CENT COL MAX COL MIN TINT SHARP SUB BIAS H.SIZE PARABOLA TRAPEZIUM COR TOP COR BTM H.COMP T.STE
Fig. 1-2
TV
00 OSD H
09 Fig. 1-1
CH-2
3. Use the Channel UP/DOWN button or Channel button (0-9) on the remote control to select the options shown in Fig. 1-2. 4. Press the MENU button on the remote control to end the adjustments.
6.5H CH-1
Fig. 2-1-A
CH-2
CH-1 6.5H
Fig. 2-1-B
D3-1
ELECTRICAL ADJUSTMENTS
(TV SECTION)
2-2: CONSTANT VOLTAGE 1. Place the set in AV MODE without signal. 2. Using the remote control, set the brightness and contrast to normal position. 3. Connect the digital voltmeter to TP401. 4. Adjust the VR1701 until the digital voltmeter is 114 0.5V. 2-3: CUT OFF 1. Adjust the unit to the following settings. R.BIAS=127, G.BIAS=127, B.BIAS=127, R.DRV=63, G.DRV=07, B.DRV=63, BRI.CENT=60, CONT.MAX=60. 2. Place the set in Aging Test for more than 15 minutes. 3. Place the set in AV MODE without signal. 4. Using the remote control, set the brightness and contrast to normal position. 5. Activate the adjustment mode display of Fig. 1-1 and press the channel button (02) on the remote control to select "CUT OFF". 6. Adjust the Screen Volume until a dim raster is obtained. 2-4: WHITE BALANCE NOTE: Adjust after performing CUT OFF adjustment. 1. Place the set in Aging Test for more than 15 minutes. 2. Receive the gray scale pattern from the Pattern Generator. 3. Using the remote control, set the brightness and contrast to normal position. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (11) on the remote control to select "R.BIAS". 5. Press the CH. UP/DOWN button on the remote control to select the "R.BIAS", "G.BIAS", "B.BIAS", "R.DRV", "B.DRV" or "G.DRV". 6. Adjust the VOL. UP/DOWN button on the remote control to whiten the R.BIAS, G.BIAS, B.BIAS, R.DRV, B.DRV, and G.DRV at each step tone sections equally. 7. Perform the above adjustments 5 and 6 until the white color is achieved. 2-5: FOCUS 1. Receive the monoscope pattern. 2. Turn the Focus Volume fully counterclockwise once. 3. Adjust the Focus Volume until picture is distinct. 2-6: HORIZONTAL POSITION 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (03) on the remote control to select "H.POSI". 4. Press the VOL. UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on right and left becomes minimum. 2-8: VERTICAL SIZE 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (06) on the remote control to select "V.SIZE". 4. Press the VOL. UP/DOWN button on the remote control until the Up/Down OVER SCAN Quantity becomes equal to the Right/Left OVER SCAN Quantity. 2-9: VERTICAL LINEARITY NOTE: Adjust after performing adjustments in section 2-9. After the adjustment of Vertical Linearity, reconfirm the Vertical Position and Vertical Size adjustments. 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (08) on the remote control to select "V.LIN". 4. Press the VOL.UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on upside and downside becomes minimum. 2-7: VERTICAL POSITION 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (07) on the remote control to select "V.POSI". 4. Check if the step No. V.POSI is "02". 5. Adjust the VR404 until the horizontal line becomes fit to the notch of the shadow mask.(Refer to Fig. 2-2).
horizontal line
,, ,, ,, , ,, ,, ,, ,,
Notch
D3-2
ELECTRICAL ADJUSTMENTS
2-10: OSD HORIZONTAL 1. Activate the adjustment mode display of Fig. 1-1. 2. Press the VOL.UP/DOWN button on the remote control until the difference of A and B becomes minimum. (Refer to Fig. 2-3).
TV
"A"
Fig. 2-4 00 OSD H A 09 B 2-13: COLOR CENTER Fig. 2-3 1. Receive the color bar pattern. (RF Input) 2. Using the remote control, set the brightness, contrast, color and tint to normal position. 3. Connect the oscilloscope to TP802. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (23) on the remote control to select "COL CENT". 5. Adjust the VOLTS RANGE VARIABLE knob of the oscilloscope until the range between white 100% and 0% is set to 4 scales on the screen of the oscilloscope. 6. Press the VOL.UP/DOWN button on the remote control until the red color level is adjusted to 110 5% of the white level. (Refer to Fig. 2-5) 7. Receive the color bar pattern. (Audio Video Input) 8. Press the INPUT SELECT button on the remote control to set to the AV mode. Then perform the above adjustments 2~6. 9. Press the DVD button on the remote control to set to the DVD mode. 10. Activate the adjustment mode display of Fig. 1-1 and press the channel button (23) on the remote control to select "COL CENT". 11. Press the VOL.UP/DOWN button on the remote control to set the same step numbers as the AV mode. White 0%
2-11: BRIGHT CENTER 1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (17) on the remote control to select "BRI CENT". 2. Press the VOL. UP/DOWN button on the remote control until the white 7.5% is begin to shine. 3. Press the INPUT SELECT button on the remoted control to set to the AV mode. Then perform the above adjustments 1, 2. 4. Press the DVD button on the remote control to set to the DVD mode. Activate the adjustment mode display of Fig. 1-1 and 5. press the channel button (17) on the remote control to select "BRI CENT". 6. Press the VOL. UP/DOWN button on the remote control to set the same step numbers as the AV mode. 2-12: TINT 1. Receive the color bar pattern. (RF Input) 2. Using the remote control, set the brightness, contrast, color and tint to normal position. 3. Connect the oscilloscope to TP803. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (26) on the remote control to select "TINT". 5. Press the VOL. UP/DOWN button on the remote control until the section "A" becomes a straight line (Refer to Fig. 2-4). 6. Receive the color bar pattern. (Audio Video Input) 7. Press the INPUT SELECT button on the remote control to set to the AV mode. Then perform the above adjustments 2~5. 8. Press the DVD button on the remote control to set to the DVD mode. 9. Activate the adjustment mode display of Fig. 1-1 and press the channel button (26) on the remote control to select "TNTCD". 10.Press the VOL. UP/DOWN button on the remote control until the tint step No.becomes "67".
100%
D3-3
ELECTRICAL ADJUSTMENTS
2-14: CONTRAST MAX 1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (21) on the remote control to select "CONT MAX". 2. Press the VOL. UP/DOWN button on the remote control until the contrast step No. becomes "60". 3. Receive a broadcast and check if the picture is normal. 4. Press the INPUT SELECT button on the remote control to set to the AV mode. Then perform the above adjustments 1~3. 5. Press the DVD button on the remote control to set to the DVD mode. 6. Activate the adjustment mode display of Fig. 1-1 and press the channel button (21) on the remote control to select "CONT MAX". 7. Press the VOL. UP/DOWN button on the remote control to set the same step numbers as the AV mode. 2-15: Confirmation of Fixed Value (step No.) Please check if the fixed values of the each adjustment items are set correctly referring below. NO. 01 04 05 09 10 18 19 20 22 24 25 27 28 29 30 31 32 33 34 35 FUNCTION OSD C H.BLK L H.BLK R VS.CORR V.COMP BRI MAX BRI MIN CONT CENT CONT MIN COL MAX COL MIN SHARP SUB BIAS H.SIZE PARABOLA TRAPEZIUM COR TOP COR BTM H.COMP T.STE RF 02 02 02 07 03 100 25 25 10 127 05 20 20 00 00 00 00 00 00 00 AV 02 02 02 07 03 100 25 25 10 127 05 20 20 00 00 00 00 00 00 00 DVD 02 02 02 07 03 100 25 25 10 127 05 20 20 00 00 00 00 00 00 00
D3-4
ELECTRICAL ADJUSTMENTS
3. PURITY AND CONVERGENCE ADJUSTMENTS
NOTE 1. Turn the unit on and let it warm up for at least 30 minutes before performing the following adjustments. 2. Place the CRT surface facing east or west to reduce the terrestrial magnetism. 3. Turn ON the unit and demagnetize with a Degauss Coil. 3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT) 1. Tighten the screw for the magnet. Refer to the adjusted CRT for the position. (Refer to Fig. 3-1) If the deflection yoke and magnet are in one body, untighten the screw for the body. 2. Receive the green raster pattern from the color bar generator. 3. Slide the deflection yoke until it touches the funnel side of the CRT. 4. Adjust center of screen to green, with red and blue on the sides, using the pair of purity magnets. 5. Switch the color bar generator from the green raster pattern to the crosshatch pattern. 6. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 7. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 8. Adjust the crosshatch pattern to change to white by repeating steps 6 and 7. 3-2: PURITY NOTE Adjust after performing adjustments in section 3-1. 1. Receive the green raster pattern from color bar generator. 2. Adjust the pair of purity magnets to center the color on the screen. Adjust the pair of purity magnets so the color at the ends are equally wide. 3. Move the deflection yoke backward (to neck side) slowly, and stop it at the position when the whole screen is green. 4. Confirm red and blue color. 5. Adjust the slant of the deflection yoke while watching the screen, then tighten the fixing screw. DEFLECTION YOKE DEFLECTION YOKE SCREW MAGNET SCREW 3-3: STATIC CONVERGENCE NOTE Adjust after performing adjustments in section 3-2. 1. Receive the crosshatch pattern from the color bar generator. 2. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 3. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 3-4: DYNAMIC CONVERGENCE NOTE Adjust after performing adjustments in section 3-3. 1. Adjust the differences around the screen by moving the deflection yoke upward/downward and right/left. (Refer to Fig. 3-2-a) 2. Insert three wedges between the deflection yoke and CRT funnel to fix the deflection yoke. (Refer to Fig. 3-2-b) RGB RGB
R G B
R G B
WEDGE
WEDGE
D3-5
ELECTRICAL ADJUSTMENTS
4. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION)
AC IN CD002
J8007
DEFLECTION PCB
TU001 CP601 VCR DECK TP401
CP802A
CRT
CD1704 CD1703
TP4201
CP1704
FB401
DVD DECK CP604
CP8001
CD1705 DVD DECK
VR404
CP602B
CP1702
CP303
VR1701
CD6
CP4502 CP603 CP602 CP8002
02
SPEAKER
CD303
CP001
CD805
CP4503
CRT PCB
CP802B CP603B CP805 J801
TP803 CD8101 TP802
FE HEAD
AC HEAD
CP803 CD803
CRT CD603
CP2201
CD2251
VCR PCB
OPERATION PCB
DVD DECK
CP8101
DVD PCB
CP2303 CP2302
CD4002
CP2301
D3-6
HA0~HA19, HD0~HD15
DVD LOADER DM3S
SDD0~SDD15
SDA0~SDA10
DVD IN/OUT CD4002 TX
Pick up
RX
3 4
1.9V 3.3V
UREG+3.8V 9
TR+/, FO+/
SPDL+/, SLED+/
12 11 5 3 1 7 9 10
LD+/
MD, MC, ML ASDATA0, AMCLK, ABCLK, ALRCLK DVD AUDIO L DVD AUDIO R
E-1
E-2
Q4507
Y/C/AUDIO/HEAD AMP IC IC4501 LA71205M-MPB 50 VX01 TIMMING 67 L H.SW H 66 AGC AMP 49 BUFFER
Q4509
BUFFER 39 OUT CCD FM MOD WC DC CLAMP NL EMPHA V/I CONV Y-LPF R R YNR/ COMB N.L. DEEM NC1 Y/C MIX 1/2 AUDIO MUTE 58 H.AMP SW VCA CLAMP 36 34 DETAL ENH DECODER 37 SERIAL 55 54 53 Y/C_CS Y/C_DATA Y/C_CLK MICON
CLAMP P P
22 21
Main CONV
KIL B.D.
PB AMP
H. AMP_SW1 C. ROTARY H. SW
FM DEM
9 7
REC AMP
P FBC R
C ROT 57 RF SW IN
VCR_A_MUTE
MICON
FE HEAD
R ALC DET
MUTE
Y/C_VIDEO
6dB 26
Q4511
BUFFER FRONT_V_IN IN/OUT
TUNER_VIDEO SW_C
V SYNC NORMAL_A Y/C_AUDIO FSC DVD_VIDEO
Hi-Fi/ DEMODULATOR
Q4503
SW
MICON
E-3
E-4
92 VCR_POWER_ON-H
TV_POWER_ON-H 56 CVIN 49 88 26 87 37 38 50 24 23 98 12 54 99 93 89 74 75 13 11
Hi-Fi/DEMODULATOR
7 AV_SW1
27 DVD_H
HIFI ENV HIFI H.SW ST SELECT OSC0 OSCI CVN2 DUMMY.V.SYNC H.SW C_ROTARY Y/C CS VCR.A.MUTE H.AMP SW1 V.REC START-H ENV.DET
DVD_H AV_SW1 RX DVD IN/OUT TX DVD RESET T-REC_LED REC_LED IN/OUT KEY-B KEY-A REMOCON_IN AT+5V CENT LED D101 CENT LED SW BOT SENSOR Q101 EOT SENSOR Q103 REEL SENS Q108 4
CP101 11 CYL FG/PG
15 RX 16 TX X101 32.768KHz 41 X0 40 XI 95 DVD RESET 90 T-REC LED 91 REC/OTR LED 81 KEY-B 80 KEY-A 5 REMOCON IN
REGULATOR
VIDEO OUT Y/C VIDEO DUMMY_V.SYNC H.SW C.ROTARY Y/C_CS VCR_A_MUTE H.AMP_SW1 V.REC_ST-H ENV.DET CTL+ CTLY/C_DATA Y/C_CLK COMP Y/C/AUDIO/ HEAD AMP
CTL(+)
Q102 2
COMP 100
Q114 POWER FAIL 1 BUFFER
POWER FAIL
TV
DEGAUSS 60
4 3
REEL-S REEL-T
AFT PROTECT SCL SDA 85 94 18 17 SW101 TAB SW EEP ROM IC IC199 BR24L04F-WE2 6 SCL 5 SDA
CAPSTAN DD UNIT
12 CYL DRIVE 10 LDM CTL 5 I LIMIT 9 CAP CTL 1 CAP FG 4 CAP.M F/R 2 CAP VCO 8 LD/CY_VCO
58 CYL SPEED UP 65 CYL_FG/PG 34 DRUM PWM 78 LDM CTL 32 CAP FULL 33 CAP PWM 21 CAP LIMIT 67 FGF
CHROMA/IF
TV_POWER_H
97
TAB SW
IC103 PST3231NR
RESET 25 EMERGENCY 86 R 61 G B BLK HSYNC VSYNC 62 63 59 46 45 1 SYSTEM RESET IC
TV_MUTE
20
TV_A_MUTE
E-5
E-6
OPEN/CLOSE
VOL DOWN VOL UP SKIP STOP PLAY SKIP POWER
3
4 2 SOUND_R+ SOUND_L+ SP_OUT_R SP_OUT_L SOUND AMP/ SURROUND
6
5 7
LED
D2205
REC/OTR LED
MICON
FRONT AUDIO L JACK J2203 2 FRONT AUDIO R JACK J2204 2 FRONT_A_IN_R FRONT_A_IN_L
Hi-Fi/DEMODULATOR
D2206 T-REC
LED
D2207
Q4204
ZERO SW
COAXIAL J8007
E-7
E-8
PROTECT
MICON
60 57 56 55 54
36 X601 3.579545MHz 35 5
MICON
V.SYNC SDA
6
TV
51 50 59
11 13 21
SCL
H.SYNC
REGULATOR
SW_C
DVD IN/OUT
40
7
25 16 14 15
TV CD603
CUT OFF 1 3 4 5 6
DVD_Y/C-Y
30
19 10 23
TV CP602
V.OUT 1 2 3 4 6 7 8 9
TV_POWER_H
MICON
EMERGENCY
TV_POWER_H
EMERGENCY SW +B DOWN
E-9
E-10
12 4 10
TV
SOUND +B
SOUND_R+ SOUND_L+
IN/OUT
SP_OUT_L SP_OUT_R
TU001 115-V-KA35ARH
3 REGULATOR P.CON+5V SCL MICON SDA AFT TUNER VIDEO 10 11 12 14 15 17
AT+30V TUNER_AUDIO
Hi-Fi/ DEMODULATOR
E-11
E-12
AGC
L/R MIX
REC LPF
VCO 1
HF1
2 22 AMP 4 3
INPUT SW
HF2 24 AMP
9 14
FRONT_A_IN_R FRONT_A_IN_L
IN/OUT
HF_COM
21 AMP 53 57 59 NC
OUTPUT SW
Y/C/AUDIO/ HEAD AMP
AMP RFC
PNR VCO-FO ADJ LOGIC FSC Y/C_AUDIO NORMAL_A 45 62 61 DBX NOISE REDUCTION DEM BLOCK FM LIM 30
BPF 48
TUNER_AUDIO
DIGITAL COMB/FILTER
29
V. REC_ST_H
28 27 25 36 LOGIC 42 43 56
HIFI_ENV
HIFI_H.SW
MICON
P.CON+5V REGULATOR
P.CON+12V
40 51 58
E-13
E-14
DVD_H AV SW1
DVD CP8001
MICON
3 4 6 7 8 9 11
P.CON+6V_DH
P.CON+5V_D REGULATOR
UNREG+3.8V UNREG+3.8V
SPDIF
AUDIO SW IC IC8001 MM1502XNRE
DVD+3.8V
P.CON+12V ZERO SPDIF-134 IN/OUT
1 4
6 2 3
1
2 3 4 6 8 10 12
DVD_H
DVD_RESET ZERO AUDIO-R AUDIO-L Y
C (CVBS)
1 4
6 2 3
CVBS
DVD_VIDEO
SW_AUDIO_OUT_L SW_AUDIO_OUT_R
E-15
E-16
AT+12V
VCR_POWER_H
P.CON+5V
P.CON+5V_A OUT IC IC3003 KIA278R05PI
P.CON+5V_D OUT IC IC3001 KIA278R05PI P.CON+6V_D OUT IC IC3002 KIA278R06PI
P.CON+5V_C
P.CON+5V AT+5V
IN/OUT
4
Q3001
BUFFER
P.CON+5V
P.CON+12V
Hi-Fi/DEMODULATOR
Q3015
BUFFER
P.CON+5V
Q3002 P.CON+8V SW
P.CON+8V P.CON+5V
DIGITAL COMB/FILTER
+30V
P.CON+6V_DH
DVD+3.8V Q3010 P.CON+5V_C SW
CHROMA/IF
P.CON+8V
E-17
E-18
TV BLOCK DIAGRAM
1
DEGAUSS RELAY RY1701
MOTOR+12V MOTOR+12V +B
CHROMA/IF
4
UNREG+8V
REGULATOR
L1703 DEGAUSS COIL D1705, D1706, D1710, D1711 AC IN F1701 TRANSFORMER SWITCHING T1701 18
UNREG+5V
DEGAUSS_H
MICON POWER_FAIL
12
SOUND +B CHROMA/IF CP603
Q802, Q803
CUT OFF
Q804, Q805
Q408 SW
BLUE AMP
DY J801 CHROMA/IF CP602B 1 6 7 2 3 4 8 9 V.OUT H.OUT P.CON+5V TV_POWER_H AFC ACL EMERGENCY +B DOWN Q407 H_VOLT_SW Q409 H_VOLT_SW 3 2 9 10 7 HV Q401 H.DRIVE 11 T401 5 2 Q403 FL OUT FB401 1 3 FBT F S 6 8 F 7 V801 CRT
E-19
E-20
F-1
Q2302 B4002 C4071_1 W854 C4039 R4041 C4089 C4044 R4054 IC4007 R4053 C4062 C4083_1 L4001 C4064 C4021 W829 C4008 R4086 1 53 C4016 C4017 R4051 C4068_1 C4067_1 C4084_1 C4070 Q2301 C2327_1 C2348 R2306 C2328_1 R2332 R2333 R2360 C2346_1 C2343_1 CP2301_1 R2355 C4100 C4063 R4040 C4090 C2340_1 R2340 C2341_1 CD4002_1 C4078_1 W804 W807 C4106 R4009 R4080 C4011_1 IC4003 R4059 C4053_1 IC4009 C4009_1 C4088 IC4001 C4074 C4109 105 157 C8122 C8113 C8126 R8112 R8101 R8113 W843 C2329_1 R4063 R4060 R4062 R4052 R2334 C2309 R2303 C2302 C2303 R2319 R2304 D2303 D2304 R2305 R2307 R2335 C4050 R4014 C2304 R2321 R2301 R2308 C4038 IC8102 C4085 R4069 C4081 R4071 B4010 C4028 R4002 X4001 R4001 R2338 IC2301 R2320 R2310 C4032 C4096 R4061 B4009 C4001 R4078 R4077 C2310_1
NTSC/PAL
CP2302
C8114 W824 W819 C8125 C8119_1 C8109 W820 C8112 L8103 C8107 L8104 C8110 C8121 L8102 C8106
C2313
W842 R4020 C4029 C4031 R4024 R4025 C4098 R4026 R4027 R4058
R2337 R2325
R4021 R4019
CP2303
R2330
R2328 C2307
D8112
D8111
C4069_1 C2314_1
DME060A
R2329
R2323
D4003
C2306 R4016
DME060A
R4036 R4037
C2358 C2360 C2359 C4035 D4005 C4026 R4045 R4072 R4018 R4012 R4042 C4027 C4025 C4045 C4046 R4064 R4008 C4024 C4023 C4022 C4020 C4019 C4013 C4010 C4047 C4018 C4014 R4087 R4022 C4033 B4014 C4002 B4016 C2318 D4002 D4004 C4034 C2301
B4001 C4030
W836 R2336 C4086 C4007 B4018 R2313 C4004 W837 R4043 R2339 B4013 C4057 B4012 C4056 C4003 B4011 R2309 B2303 C4075 B4003 C4072 C2326 B2305 C4076 B2304 C2347 C2332 C2315 R2318 R2341 C2365 R2302 Q2305 R2348 Q2304 R2347 C2342
R2359
C2331
F-2
CD1705
CD1702
CP601
J8007
F1701
FH1702
W009 D1732 B8001 R1701 CD1704 Q1702 C1701 W021 W020 L1701 C1708
7 R1 18
W843
HS351
C357 L8002 L001 C3002 D3004 D1702 IC3003 C1712 Q1706 D1717 R1714 W023 C4204 W013 D1706 CP1708 D1710
TH 170 1
W007
R1726
R353
C4205
W971
C3022 IC352 R3006 Q3002 W002 R3010 C328 HS3002 D3008 W022 D1730 D3010 C3007 W011 S808Y Q3007 R1708 W912 T1701 C1727 D1707
7 D1 04
S813X
W316
C3005
R359
W008
5
TU001
W012
W016 W014 IC3002 R3009 IC3001 W015 C1718 D1723 C1732 S824X R1703 C1731_1 W082 C1733 W928 D1722 R1717 C1720 S813Y C3010 C1705 C1724 D1734 C1715 D1718 R1721 W821 S822Y
D1 W345 71 9
D1705
C321 C3009
W970
C005
C1710
R3001 Q3014
C350_2 W003 W004 W006 R3004 C1716 W039 W044 D3009 L3002 C3013 D1716 HS1701 W033 W066 W034 W028 W035 W029 W036 W031 W032 D3003 D1715 C3025 R1724 S801X D3001 S822X W074 CP1702 W072 W071 D1737 D1727 D1721 C1711 R1725 C1728_1 D1712 R1712
1 R17 0
IC1701
W005
W925
R1720
W905
W914
R3002
R3003
W938
D3005 C1713_1
W076
W848
W040 CD002 W045 W068 W064 W070 W067 W065 CP8001_1 D1724 IC1702 D1733 D1720 D1728 D1703 R1706 W055
R3012
B1703 D1726
W049
W050
W363
C3028
D1713
W043 W041
W037
W056
VR1701
W025
W894
R1727 C1717_2 D106 D4207 W060 W059 W073 W856 L4504 R4512 Q4505 W054 C4506 C4511 W123 C5554 CP4501 W126 C5536 W926 C5543 W135 R5525 C4527 W121 C4532 C4540 C4518 C5559 W116 W119 W118 C4539 W130 C4548 L5503 C4508 C4544 S808X C5544 C4568 C4576 C4564 X4501 W891 W127 C4545 C4567 C4566 W846 R4557 W937 W155 L4509 W136 D602 W874 W196 D605 W139 W192 W154 W201 W153 W172 W170 W205 W144 W827 W167 W165 W162
Q101
W075
Q1705
W047 W038 W024 W809 S809Y CP4502 C5545_1 W877 W080 C4529 W864 C5555_1 W069 W114 W077
W048 W051 S809X C128 W052 W091 W092 W093 W094 W046
CP6 02 R635
CP8002
CP603
S801Y
W090
W893 W109 L4502 W915 R627 W107 W108 W892 R605 W102 W122 W101 W099 W098 Q4504 W097 W096 W129 R613 C624 C603 W103 W104 W933 R4522 C4565 C4571 W100 W120 W117 R4537 C4558 C4570 R4559 L4506 W131
D603
W095
W111 C4523
SOLDER SIDE
R8012
R622
R173
C5530
C5526 C5515 C5520 C5512 C5523 C5551 L5501 C5542 C5524 D5501 C5525 L8001
C609 W105 L601 W115 W113 W112 D601 C4581 W208 D5502 W197 C4572 C4574 W870 W189 W187 W182 W183 W164 W169 W174 W195
C4550
C5540 C5528
R3021
DME069A
W213 W218 W217 R3020 L5504 W240 W185 W229 W215 W214 W181 W230 W228 W221 W219 W216 W212 W247 W227 W222 W845 C3016 W242 W243 W854 W186 R153 W191 W231 C104 W238 W241 W225 W248 W226 D3002 W249 W245 C1520 L8003 C8009 X102 X101 W303 W304 W305 C8007 W314 TP5501 W239 W235 W823 W286 Q107 W301 C8015 TP4501 TP102 W307 R122 W308 R128 C2210 W850 C2212 W841 W842 R2225 W312 W917 R4528 W282 W281 W280 S101Y SW101 W283 C2208 R144 W306 C2206 W279 W302 W315 J2201 SW2202 SW2201 J2204 J2203 J2202 W813 R2226 W309 W310 W311 W916 B2201 W880
W110
CP
CP4503
C5502
W908
W158
X601
W138
W137
C632
W166
W171
D103 W151 W180 R164_1 W268 W261 W265 W254 C122 W267 C129 W269 W278 Q104 W252 W277 D105 W251 D102 W274 R113 W258 W816 W844 W257 W260 W276 W263
05 Q1
W250
Q1
08
R125
W299 C146 W292 W293 W294 W291 W298 W275 C139 W272 W271 W300 W806 W296 W297 W288 W287 C141
W289
W270
R2211
R2224
R2223
R2227
R2212
CP2201
W838
C2204_1 OS2201
SW2206
SW2205
D2206
D2205
D2207
SW2207
D2201
W290
SW2204
W285 W284
W194
W150
R632
R114
SW2203
S101X
R623
W175
C119 W179
W145 W143
W163 W161
W198
R131 W178
W168
W149
W157
C113
W176
W193
W833
W819 W810
R4562 W207
W190
F-3
Q103
CP303 C320
F-4
R4540 R4536
SOLDER SIDE
Q605
R628
R4550
C4501 R4503
C4551 C4553 C4552 R4546 R4502 C4557 R4521 R4519 C4534_1 C4573
C617 C614
W858
R607 C613 C618 R617 R615 C619 C611 Q601 17 R610 C607 R633 R608 R612 R634 C608 R110 C118 R115 R116
C4561 R4544 C4556 C4559 C4538 C4555 R4560 C4549 C4569 Q602 R4505 R147 R4509 Q4503
Q4507 Q4509
R8032
R5502
C4579
R134 C138 1
W887
Q116
C4580 49 Q102
R624 C626 C630 C629 C628 R625 R626 C627 C625 R620 C631 C164 C106 C616
R120 R8031 C137 R636 R148 R150 R1530 R1509_1 Q606 R159 R177 Q112 R4530
R103
R171
C117
R108 C110
C604 R104
R630 R160
R149
C114
R166
R136
R137 C2201 R2208 C2205 R2206 R152 C143 C2203 R2204 R2203 R2201 R2205 C2202 R2202
1 10
01 45
C634
IC
IC
F-5
R8003 R8005 C8010 R8004 Q8002 C8095 R4213 W934 R1705 R8006 C004 R8013 R8007 C1709 C358 R318 Q3015 R317 R3016 W811 R3024 R357 Q353 W837 C001 W835 R3007 Q3001 C006 W361 C3024 C8017 C8019 W815 W849 R3011 R3019 C3027 R303 R1716 R1709 C1703 R1707 C1702 W886 W881 R3005 R307 C302 Q350 R3023 W829 C3001 Q3011 R301 R1719 R1713 R4215 Q4204 IC602 C1525 R1517 W889 C112 R4511 W804 C5553 C4524 R4501 C5552 C4537 C5558 C5560 R4527 R4520 C4517 R4526 C4536 C4533 C4542 C4541 R4529 R4532 R4533 R4513 R4508 R618 1 C5549 C4514
IC
R1715
C1722
R304
C8020
R5510
R4531
R4507
C5538
R603
C5534 17 1
R4219
R5518
33
C4522 21 R4553 Q4511 61 C4521 C4505 C5563 41 C5550 R5514 R5519 R4524 C5556 R4539 R4534 C4546 R4541 R4545 C4535 R4523 R4525 C131 C132 C130 R129 C135 C133 R176 C148 C145 51 R132 R135
55 01
C5518 49 C5529 C5501 C5513 C5509 R5503 C5504 C5510 R5523 C5506 C5511 C5522_1 R5504 C5517 R5522 R5506 C5521 C8012 IC8001 C5562 R8029 C8014 IC199_1 R111 C154 76 Q106 26 C151 1 W885 R123 C136 R8021 C2207 R143 R140 R107 R139 R8020 C2209 C2213 IC8002 C5527 R5507 R5509
DME069A
R8030 C5503 R5508 W872 C107 R105
W865
F-6
HS401
SW2258
CEE055B
R414 W017
Q403
B403 C408_1 R2257 CC801 D804 W822 C412 C816 D805 D806 C815 R818 R817 C819 C817 C818 CP603B R825 R807 W018 C801 R824 SW2257 CP802B C402 R819 W831 L402 R826 W833 Q805 W832 D801 R810 Q803 W834 R806 R2255 SW2255 R815 D802 Q804 R805 D412 R821 R814 D803 R822 Q802 R449 C445 R816 R820
01 J8
C418_3 FB401_2
R412
R2256 SW2256 SW2254 R2254 SW2253 R2253 SW2252 W022 W021 W805
R454
Q807
CME029B
R452
C446
R809
C406_1 R407
CP404
_3 45 R4
W002
R438
W004 D402
W003
C436
2A 80 CP
C430
C 3 42
C434
C404
W020
R424
R432
R430
CD807
R447
R415
R444
D413
R413 R437 Q407 T401_1 W023 CP803 Q409 R442 R441 D404 R418
W851
SW2251 CP805
R2252
R2251
CCE024B
W806 C820
C405_1 C438_2
D410 D418
W015
TP401 Q408
CP804 CP001
R417
W009
CD2251
CD808
F-7
F-8
(DVD PCB)
(DVD-L/CD-H) TOUT_SW TIN_SW SPDL_SENSOPU_D DVD_LD CD_LD DVD/CDPD DVD/CDPD OPU_C OPU_B DRVSB (MUTE-L) OPU_A C4057 B4013 180P CH MMZ1608R102CTDVD/CD RF D4001 DUPTD1 1SS355 3.3 R4011 4.7K 5.2 LEVEL CONVERT Q4004 2SC3052-T1 47P CH C4043 47K 100P CH C4091 RX
MMZ1608R102CT
FPCSTRB
(VR_DVD) (VR_CD)
IRRCV
B4011
NC R4052
FROM/TO AUDIO/VIDEO
2.9 R4013
C4042
TP4026
TP4025
10P CH
4.7K
JG008 JG009
W837 0.1 F
B4016 MMZ1608R102CT
C4088
C4033
C4004
R4022
VDDDAC VDDAFERF
SYS_MUTE DVD-H DAC_VIDEO_C DAC_VIDEO_B DAC_VIDEO_D ASDATA0 ABCLK ALRCLK AMCLK MD MC ML P-H/I-L RESET P.CON+5V GND (GND,D_GND)
6.3V 47 KA C4068_1
C4067_1
R4036
4.7K R4038
P.CON+3.3V
0.1 F
RFINN RFINP
0.1 F
47 KA
0.1 F
C4072
C4075
0.1 F
0.1 F
6.3V
C4076
W829
4.7K
3.3 3.3 0 3.3 3.3 3.3 3.3 3.3 3.3 3.3 0 3.2 3.3 3.3 0 0 3.1 1.8 0 0 3.1 3.1 0.3 0.3 1.3 1.3 2.2 2.4 2.1 2.3 0 3.5 2.4 0 2.3 3.3 3.3 2.4 3.3 2.4 0.1 1.6 1.8
4.7K
6
HA0 HA1 HA2 HA3 HA4 HA5 HA6 HA7 HA8 HA9 HA10 HA11 HA12 HA13 HA14 HA15 HA16 HA17 HA18 HA19 HD0 HD1 HD2 HD3 HD4 HD5 HD6 HD7 HD8 HD9 HD10 HD11 HD12 HD13 HD14 HD15
GND P.CON+3.3V NC 3.3 3.3 NC 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 0 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 NC 3.3 3.3 3.3 3.3 1.8 3.3 3.3 3.3 0 3.3 3.3 0 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 0 3.3 3.3
DUPTD0 DUPRD0 PWMCO(0) IDGPCI/O(4) GPCI/O(46) VDDPWM PWMCO(4) GNDPWM PWMCO(3) PWMCO(2) SPINDLEPULSE SLEDPULSE VDD-IP ICGPI/O(7) ICGPI/O(6) GNDP IDGPCI/O(3) VDDP ICGPCI/O(5) ICGPCI/O(4) GNDC GPCI/O(32) VDDC AGND1 AGNDREF DVD_LD CD_LD DVD_MD CD_MD RESOUT VBGAP VC F K E AGND J D H C AVDD SVDD B AVDD1
208 207 206 205 204 203 202 201 200 199 198 197 196 195 194 193 192 191 190 189 188 187 186 185 184 183 182 181 180 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163 162 161 160 159 158 157
MMZ1608R102CT TRAY_OPEN TRAY_CLOSE HOME TOUT_SW TIN_SW DVD/CD DRVSB RF OPU_A OPU_B OPU_C OPU_D OPU_E OPU_F VC SPDL_SENSSPDL_SENS+ DVD/CDPD DVD_LD CD_LD SPINDLE_PWM SLED_PWM TRACK_PWM FOCUS_PWM P.CON+A5V P.CON+3.3V VCC+6V M_GND GND L4002 W5T29X7.5X19 C4036 0.1 B C4097 0.01 B 47 KA
C4008 HA15 HA16 HA14 HA13 HA12 HD15 HA11 HD7 HA10 HD14 HA9 HD6 HA8 HD13 HD5 C4010 HD12 WR HD4 HD11 HD3 HA19 HD10 HA18 HD2 HA17 HD9 HA7 HD1 HA6 HD8 HA5 HD0 HA4 RD HA3 HA2 MEMCS0 HA1 HA0 BOOTSEL1 BOOTSEL2 C4014 0.1 F 0.1 F 0.1 F
C4013 0.1 F
MEMCS0 RD WR SD_A0 SD_A1 SD_A2 SD_A3 SD_A4 SD_A5 SD_A6 SD_A7 SD_A8 SD_A9 SD_A10 SD_D0 SD_D1 SD_D2 SD_D3 SD_D4 SD_D5 SD_D6 SD_D7 SD_D8 SD_D9 SD_D10 SD_D11 SD_D12 SD_D13 SD_D14 SD_D15 RAMCS0#
R4080 R4009
C4026
0.1 F DVD-H TP4024 P.CON+3.3V B4006 (250mA) MMZ1608R102CT 100 KA R4070 C4083_1
61 62 63 64 65 66
SSCRXD MEMCS(1) VDDP MEMAD(15) MEMAD(16) MEMAD(14) MEMAD(13) MEMAD(12) MEMDA(15) MEMAD(11) MEMDA(7) GNDP MEMAD(10) MEMDA(14) MEMAD(9) MEMDA(6) MEMAD(8) MEMDA(13) MEMDA(5) MEMAD(20) VDDP MEMDA(12) MEMWR# MEMDA(4) VDDC MEMDA(11) MEMDA(3) MEMAD(19) GNDC MEMDA(10) MEMAD(18) GNDP MEMDA(2) MEMAD(17) MEMDA(9) MEMAD(7) MEMDA(1) MEMAD(6) MEMDA(8) MEMAD(5) VDDP MEMDA(0) MEMAD(4) MEMRD# MEMAD(3) MEMAD(2) MEMCS(0)# MEMAD(1) MEMAD(0) GNDP VDD-IP VDDP 53 54 55 56 57 58 59 60
75 +-1% R4004
RAMADD(6) VDDP RAMADD(1) RAMADD(7) RAMADD(0) GNDP RAMADD(8) VDDC RAMADD(10) GNDC RAMADD(9) VDDP RAMADD(11) RAMCS(0)# RAMBA(1) RAMBA(0) GNDP RAMCS(1)# RAMRAS# RAMCAS# VDDP RAMWE# RAMDQM GNDPCLK PCLK VDDPCLK RAMDAT(8) GNDP RAMDAT(7) RAMDAT(9) RAMDAT(6) VDDP RAMDAT(10) RAMDAT(5) RAMDAT(11) GNDP RAMDAT(4) VDDC RAMDAT(12) GNDC RAMDAT(3) VDDP RAMDAT(13) RAMDAT(2)
TP4019 0 0 W836 2.6 3.2 1.8 3.3 C4069_1 0 6.3V 47 KA 0 3.3 3.3 HOMEJG028 PM16 2.9 (MIC_DET) 3.3 (DJTDO) 3.3 I2C_CLK 3.3 I2C_DAT 1.8 0 (ICETCK) 3.3 (ICETDO) 3.3 (MUTEC) 3.3 (ICETMS) 3.3 JG021 3.3 (PM11) 0 TP4017 3.3 TP4018 3.3 3.3 R4024 3.3 4.7K 3.3 0 3.3 3.3 0 3.3 0 ASDATA1 0 ASDATA2 3.3 0 MIC_ON 0 NC 0 0 3.3
75 +-1% R4003
208 SSCTXD
GNDDACBS2 GNDDACP RSET C/B/U VDDDAC Y/R/V CVBS/C VDDDAC 160 A CVBS/G/Y 159 G Y/C 158 RFN GNDDACD GNDDACD 157 RFP GCLK XO VDDA RESET# GNDA GNDP VDDP IDGPCI/O(2) GPCI/O(31) DJTCK / ICGPCI/O(3) / VID(0) DJTO / GPCI/O(30) / VID(1) DJTDI / GPCI/O(29) / VID(2) DJTMS / GPCI/O(28) / VID(3) MPEG/MICON/DSP/RF_AMP IC VDDC GNDC IC4001 GPCI/O(27) ZR36862PQCG-B IDGPI/O(1) ICGPCI/O(2) GPCI/O(26) VDDP ICGPCI/O(1) GNDP HSYNC VSYNC AIN VDDP-A2 AMCLK 100 RAMDAT(14) GNDP-A2 101 GNDP ABCLK ALRCLK 102 RAMDAT(1) GPAI/O 103 RAMDAT(15) AOUT(0) AOUT(1) 104 RAMDAT(0) AOUT(2) SPDIF IDGPCI/O(0) ICGPCI/O(0) GNDP GPCI/O(20) VDDP 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104
52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
R4005
P-H/I-L
0.1 F
C4027 0.1 F
10 33 33 33 R4069 4.7K
TP4008 C4084_1
C4065 0.01 B
6.3V
TP4010
W842
FROM/TO DVD IN/OUT DVD/VR 130mm DVD COMBO 250mm TP4012 TP4011 CD4002_1 (CP8001_1) CU2B3301 GND(D) TP4013 GND(D) SSCCLK/TX TP4014 TP4020 W850 TP4021 C4066 1 B TP4022 RDY(I/O(0))/RX GND(M) P.CON+6V P.CON+A5V UNREG+3.8V UNREG+3.8V GND(A) SPDIF 1 2 3 4 5 6 7 8 9 10 11
TP4009
RX C4031 0.01 B IAMCLK IABCLK IALRCLK JG024 TP4015 TP4016 JG020 R4058 C4098 4 B4010 R4071 150 220 ASDATA0 REG+3.3V +1.9V IC IC4003 BA33E00WHFP R4025 220 R4026 R4027 220 ABCLK 220 ALRCLK 3 AMCLK M_GND VCC+6V P.CON+A5V
W807
L4001 0305
P.CON+5V 2.2uH
TP4027 SPDIF SSCRXD SSCTXD GND 8 4 0 VO1 5 3.3 VO2 6 1.8 ADJ 7 0.8 TP4028 TP4001 TP4002
10P CH
MMZ1608R102CT
R4014
4.7K
3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 0 3.3 1.8 3.3 0 3.3 3.3 3.3 3.3 3.3 0 3.3 3.3 3.3 3.3 3.3 3.3 0 3.0 3.3 3.3 0 3.3 3.3 3.3 3.3 3.3 3.3 3.3 0 3.3 1.8 3.3 0 3.3 3.3 3.3 3.3 3.3 0 3.3 3.3 3.3
C4011_1
C4052
C4012
0.1 F
C4053_1
6.3V
100 KA
0.1
16V 47 KA
C4009_1
C4015
6.3V
0.1
C4080
TP4023 47K
C4082
100 KA
C4018
C4019
C4020
C4024
R4059
C4023
C4025
UNREG+3.8V F
0.1
C4090
C4089
C4100
6.3V
6.3V
PCB130 DME060
RAMRAS# RAMCAS#
RAMCS0# SD_BA0
RAMWE# RAMDQM
RAMCLK
SD_D12
SD_D8
SD_A10
SD_D4
SD_D3
SD_A8
SD_A9
TP4003
1
2
NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
G-1
G-2
(DVD PCB)
FROM/TO MPEG/MICON/DSP SD_A0 SD_A1 SD_A2 SD_A3 SD_A4 SD_A5 SD_A6 SD_A7 SD_A8 SD_A9 SD_A10 SD_D0 SD_D1 SD_D2 SD_D3 SD_D4 SD_D5 SD_D6 SD_D7 SD_D8 SD_D9 SD_D10 SD_D11 SD_D12 SD_D13 SD_D14 SD_D15 RAMCS0# RAMRAS# RAMCAS# SD_BA0 RAMDQM RAMWE# RAMCLK HA0 HA1 HA2 HA3 HA4 HA5 HA6 HA7 HA8 HA9 HA10 HA11 HA12 HA13 HA14 HA15 HA16 HA17 HA18 HA19 HD0 HD1 HD2 HD3 HD4 HD5 HD6 HD7 HD8 HD9 HD10 HD11 HD12 HD13 HD14 HD15 MEMCS0 RD WR P.CON+3.3V C4095 FLASH IC 8M IC4007 SST39VF1601-70-4C-EKE 48 1 HA16 C4064 0.1 F 46 0 0.7 1.9 1.3 1.2 0.6 0.7 0.8 1.6 C4062 0.1 F HD11 HD3 HD10 HD2 HD9 HD1 HD8 HD0 RD 1.6 1.6 1.3 1.2 1.4 1.4 0.9 1.6 2.6 0 2.6 2.5 R4040 4.7K 3.3 GND DQ15 DQ7 DQ14 DQ6 DQ13 DQ5 DQ12 DQ4 VCC DQ11 DQ3 DQ10 DQ2 DQ9 DQ1 DQ8 DQ0 OE# GND CE# A0 A13 A12 A11 A10 A9 A8 A19 A20 WE# RP# VPP WP# A19 A18 A17 A7 A6 A5 A4 A3 A2 A1 0.8 3 1.5 4 2.5 5 1.3 6 1.6 7 1.5 8 0 40 9 0 NC 3.3 0 37 12 0.1 36 13 0.1 35 14 C4039 0.1 F R4041 RAMDQM 4.7K 0 34 15 HA19 (W838) HA18 HA17 HA7 HA6 HA5 HA4 HA3 HA2 HA1 RAMCLK 5 2.3 3.3 R4048 47K 0 NC 3.3 3.3 3.3 3.3 3.3 3.3 0 3.3 WR RESET HA13 HA12 HA11 HA10 HA9 HA8 (W837) HA19 3.3 SD_D13 C4109 44 HD7 HD14 HD6 HD13 HD5 HD12 HD4 SD_D12 0.1 F C4040 0.1 F 3.3 3.3 3.3 3.3 3.3 SD_D9 SD_D8 C4041 0.1 F 3.3 3.3 3.3 0 NC 3.3 1.2 3.3 A16 VCCQ A15 A14 1.7 1.0 2 HA15 HA14 SD_D15 SD_D14 0 3.3 3.3
16M SDRAM IC IC4009 M12L16161A-7TG 50 VSS DQ15 DQ14 VSSQ DQ13 DQ12 VDDQ DQ11 DQ10 VSSQ DQ9 DQ8 VDDQ NC UDQM CLK CKE NC A9 A8 A7 A6 A5 A4 VSS VDD DQ0 DQ1 VSSQ DQ2 DQ3 VDDQ DQ4 DQ5 VSSQ DQ6 DQ7 VDDQ LDQM /WE /CAS /RAS /CS BA A10/AP A0 A1 A2 A3 VDD 1 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 0 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 C4047 0.1 F C4046 0.1 F 37 14 RAMDQM RAMWE# RAMCAS# RAMRAS# RAMCS0# SD_BA0 SD_A10 SD_A0 SD_A1 SD_A2 SD_A3 SD_D6 SD_D7 C4045 0.1 F 43 8 SD_D4 SD_D5 SD_D2 SD_D3 C4050 0.1 F 49 2 SD_D0 SD_D1
47
48
47
45
46
HD15
45
43
44
42
SD_D11 SD_D10
41
42
39
10
41
38
11
40
38
36
33
16
35
32
17
34
31
18
30
19
29
20
30
28
21
27
22
26
23
25
24
26
25
27
24
FLASHCS
SD_A4
28
23
SD_A5
29
22
SD_A6
21
SD_A7
31
20
SD_A8
32
19
SD_A9
33
18
17
16
15
13
39
12
11
10
6.3V 100 KA
GND
W854
0.01 B
6.3V 100 KA
0.01 B
0.1 F
C4044
C4074
C4099
0.1 F
C4063
C4106
C4021
PCB130 DME060
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
G-3
G-4
(DVD PCB)
DVD_LD CD_LD DVD/CDPD (VR_CD/VR_DVD) DM3S DVD/CD VC FROM/TO MPEG/MICON/DSP DVD/CD DVD_LD CD_LD DVD/CDPD RF OPU_A OPU_B OPU_C OPU_D OPU_E OPU_F VC HOME GND GND 0.001 B C2318 TOUT_SW TIN_SW P.CON+A5V TRACK_PWM FOCUS_PWM P.CON+3.3V
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
TT+ FF+ MON(DVD) NC(SW) VOL(DVD) GND(DVD) LD(DVD) LD(CD) VOL(CD) GND(CD) MON(COM) DVD/CD RF C B A D F E VCC Vref GND(PDIC) C2331 6.3V 47 KA C2329_1 0.1 F C2315 TO LOADER 0.1 F TP2303 DVD/CDPD DVD_CD JG016 JG040 JG011 JG010 JG013 JG015 JG014 VR/CD NC VR/DVD JG056 DVD/CDPD
TRTR+ FOFO+ 6.3V 47 KA C2347 6.3V 47 KA C2346_1 C2343_1 C2332 F 0.1 F C2342 C2309 0.1 F 1B
0.1
0.1
82
C2327_1
CDLD R2359 82 VR DVD Q2305 2SC3052-T1 0.1 R2348 0 0.1 3.3K W843 0.1 0.7 0 DVD/CD Q2304 2SC3052-T1 VR DVD Q2303 2SC3052-T1
47 KA
DVDLD
R2356
JG017
JG018
C2326
RF_A5V
R2306 0 0 6.8 R2346 0.7 3.3K DVD LD CTL Q2301 2SA1036K R2318 4.5 3.9 1.0 R2347 3.3K C2340_1 6.3V 100 KA B2301 MMZ1608R102CT C2341_1 6.8 R2332 220 TP2307
6.3V
6
SPINDLE_PWM SLED_PWM VCC+6V
M_GND R2319 TP2320 R2313 100 +-1% R2309 TP2322 TP2308 4.7K TRACK_PWM SPDL_SENS+ R2334 10K SPDL_SENSTP2323 TRAY_CLOSE R2324 1K TP2324 TRAY_OPEN 3.3K
B2302 R2360 33
1K
R2301
R2307
TP2321
R2310
5.6K
4.7K
2 1
R2338 4.7K
MMZ1608R102CT
MUTE1
VCONT
MUTE234
REG-OUT
VIN+OP
VREF-OUT
VO_OP
S-GND
VIN4
VIN-OP
REG-IN
VIN4-
VREF-IN
VIN3-
VIN2+
VIN2-
VIN3
VIN2
44
43
42
41
40
39 NC
38
37
36
35
34 NC
33
32
31
30
29
28
27 NC
26
25
24
23 NC
10K
4.0
3.1
3.1
1.6
1.6
1.6
1.6
1.6
R2337
0 NC 1.6
0 NC 1.6
0 NC 6.0 NC
0 NC 1.6
0 NC 1.8
TP2318
100 R2352
27K
OPEN
R2321
R2353 TOUT_SW
4.7K
LD+
R2327
MOT_LD+
R2326
C2348
JG019
6.8
0 NC
R2335
LD-
TP2319
MOT_LD-
6.3V 47 KA
10K
R2341
R2305
CP2302 00_6232_005_006_800+
1K
C2328_1
R2355
75K
OPU_VREF
33K
MMZ1608R102CT
6.3V 100 KA
R2320 4.7K
VC2
4
TP2316
R2342
4.7K
100P CH
100P CH C2358
100P CH
C2360
VIN1+A
VIN1-A
VD3-
VD2-
VD1-
VCCS
C2357
100P CH
C2359
1 0 0
2 6.0
4 0 NC 0.5
5 0.5
6 2.6
7 2.6
8 2.5
9 2.8
10
11 0
12 0 3.5
13 1.7
14 2.6
15 2.6
16
17 0 NC 6.0
18 6.0
19
20 0 1.6
21 1.6
22
VIN 1
VCC2
VCC1
VLD+
VD4+
VD3+
VD2+
VD1+
FWD
VLD-
VD4-
REV
NC
NC
4 3 2 1
100 MOT_SLEDMOT_SLED+ MOT_SPDLC2306 0.1 F C2314_1 C2301 MOT_SPDL+ 10V 100 KA C2310_1 10V 100 KA F R2328
R2325 6.8K
1K
FROM/TO LOADER
TP2317 R2330
PGND2
PGND1
TP2309
TP2310
TP2311
TP2312
TP2313
TP2314
TP2315
C2365
0.1
R2302
0.1
100
+-1%
4.7K B
0.022 B
2.2 0.1 B 2.2 R2323 1.2 C2307 R2329 0.1 B JG057 1.2
R2358 120
MOT_SPDL+
MOT_SLED-
MOT_LD-
MOT_SLED+
MOT_SPDL-
JG058
MOT_LD+
TR+
FO+
TR-
FO-
C2305 0.1 B
C2304
D2303
R2357
1K
1SS355
0.1 B
D2304 1SS355
PCB130 DME060
NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
G-5
G-6
1 Y V U C
2 G R
3 CVBS Y
C/B/U 8 Y/R/V 9 CVBS/C FROM/TO MPEG/MICON/DSP DAC_VIDEO_C DAC_VIDEO_B DAC_VIDEO_D P.CON+5V DAC_VIDEO_C 150P CH C8105 150P CH 12P CH L8102 1uH 0305 W818 10
C8104
6
RESET MC MD ML AMCLK ABCLK ALRCLK ASDATA0 P-H/I-L DVD-H SYS_MUTE GND
C8106
DAC_VIDEO_B 150P CH
W819
DAC_VIDEO_D 150P CH
W820
DVD-H P-H/I-L
R8101 100 NC NC NC
TP8101 TP8102 TP8103 TP8104 TP8105 TP8106 W826 FROM/TO DVD IN/OUT DVD COMBO 180mm CP8101_3 (CP8002) IMSA-9604S-12F EXT_MUTE DVD RESET ZERO W824 TP8109 TP8110 TP8111 TP8112 TP8113 TP8114 AUDIO-R GND AUDIO-L GND Y GND C GND CVBS 12 11 10 9 8 7 6 5 4 3 2 1 CD8101 2F0C1602 FFC(1.0mm pitch)
C8110
C8112
RESET ZERO R_AUDIO L_AUDIO (D_GND) 100 KA DAC_B_VIDEO DAC_C_VIDEO DAC_D_DVD_VIDEO 0.001 B C8122 D8112 1SS355 D8111 1SS355
TP8107 TP8108
C8120
0.1
C8119_1
6.3V
TO MEMORY RESET
SYS_MUTE B8103 MMZ1608R102CT C8114 1 B C8125 1 B C8113 1 B C8126 1 B R8112 470 7 R8113 470 6
3
2.4 STEREO DAC IC IC8102 PCM1753DBQR 2.5 4.9 3.3 NC 5 VDD 0 1.6 1.1 1.6
8 VOUTR
7 VOUTL
6 VCC
4 DGND
3 LRCK
2 DATA ML
1 BCK SCK
ZEROR/ZEROA
ZEROL/NA
VCOM
AGND
MD 13 0
9 0 2.4
10 3.3
11
12 0 NC
14 15 16 0 3.3 1.7
2
6.3V 100 KA C8121
MC
ASDATA0
ZERO
ALRCLK
AMCLK
ABCLK
MD
MC
ML
PCB130 DME060
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
G-7
G-8
1/4W
0305
L4506
R4545
R4523
22K
R4530
L4505
0305
12 R4537
R4506
12K
R4525
4.0
12K
47uH
W864
47K
0.1
P.CON+8V P.CON+5V
R4524
6.3V 47 KA
FROM REGULATOR
W854
1.8K 1/4W
C4538
C4545
47uH
R4528
22K
3.3K
1K
50V 1 KA
C4543
50V 1 KA
C4535
C4547
0.1
C4556
C4546
0.01
B C4558 KA FROM/TO MICON Y/C_CLK B Y/C_DATA Y/C_CS C4559 1/4W 0.1 B R4559 H.SW VIDEO_OUT ENV_DET VCR_A_MUTE CTL+ CTLC_ROTARY DUMMY_V.SYNC V.REC_ST_H R4557 C4565 25V 10 KA C4570 C4566 50V 1 KA C4569 0.1 B C4567 FROM DVD IN/OUT 2.3 28 1.6 27 2.9 26 50V 0.22 KA C4564 10V 33 KA FROM DIGITAL COMB/FILTER 3.6 NC 0 4.9 L4509 P.CON+5V R4550 C4568 2.2M R4553 R4562 100 11 100uH 0607 Y/C_VIDEO 180 1/4W 180 1/4W Y/C_VIDEO DUMMY_V.SYNC AUX_V[F/R] TUNER_VIDEO C4576 DVD_VIDEO 50V 1 KA 50V 4.7 KA C4572 50V 1 KA V.SYNC W870 AUX_V[F/R] 82K 1/4W R4560 100K C4574 FROM/TO TV POWER 3.1 50V 1 KA GND H.AMP_SW1 COMP Y/C_VIDEO 3.1 35 6.3V 47 C4561 0.01
R4534
Y/C_AUDIO FSC HF2 HF_COM HF1 Y/C/AUDIO/HEAD AMP IC IC4501 LA71205M-MPB 0.5 60 C4521 0.068 C4522 C4514 0.047 B 0.047 B B 2.2 61 0 62 4.0 63 1.8 64 0.7 65
P
8.2K
C4549
0.022
R4539
1.5K
0.022
6
FROM/TO CYL CP4501 TOC-C09X-A1 9 8 7 CD4501 2F061502 6 5 4 3 2 1 HF1 (R) HF COM HF2 (L) SP-CH1 (R) SP COM SP-CH2 (L) EP/LP-CH1 (R) EP/LP COM EP/LP-CH2 (L)
100CT3R502 3.579545MHz
X4501
2.8 59
0 58
0 57
0 4.8 4.8 4.8 5.0 1.9 2.6 4.0 3.3 3.3 2.3 5.0 5.0 56 55 54 53 52 51 50 49 48 47 46 45 44
SERAIL DECODER C-VCC VX01 320FH VCO
P R
NC
0 2.2 0.8 43 42 41
4Fsc PLL OUT AUTO-BIAS VSS CLAMP CLOCK 0 VSS
OUT ENV COMP DET KILL DET HA GND CHROMA DET ACC DET
SLD
40
ALWAYS VDD 5V
1.7
TIMMING DRIVER CCD
BGA BGA
OUT
39
38
REC APC
PB APC
REC AFC
0 3.0 37 2.8 36
2.3
BEFORE
IN
AFTER
0.7 66
R H
P R
BGA
R P
2.2K
0.7 67
P
68
HA VCC
47 KA
B C4508
1.7 69
P
33 2.0 32
P.CON+5V
W891
5.0
C-LPF
Main CONV
34 2.6
3.58M BPF1
PB-C
1.8 70 0 71 2.0 72
P H L R
1 2 3
TUNER_VIDEO
FROM CHROMA/IF
4.0
REG 4V
C4505
6.3V
0.33
YNR/COMB
P R R
VIDEO AGC
31 2.0 30 2.3 29
CLAMP
P
2.0 73
PB-C
1/2 FBC
R P R P
BAL TC1
NL EMPHA FM MOD
R-EQ TEST NORMAL
Y-LPF
R
2.0 74
P
Y/C MIX
0 75
A-GND
1 2 3
2.2 76 4.9 77
A-VCC ALC DET PB,EE EQ AMP SP,LP PB,EE REC:LP<EP PB:EP VREF REC AMP MUTE
P R
DOUBBLE LIM
FM DEM
ALC
R P
LPF
LINE AMP
2.3 78 C4523 C4517 0.1 B 16V C4524 0.1 R4512 10 W877 1/4W C4529 6.3V 470 YK COIL,BIAS OSC L4502 1626009 C4532 10V 33 KA C4533 0.01 BIAS CTL Q4505 KTA1266 0 100uH 0305 0.01 B R4508 6.3V 220 YK C4513 C4512 3.3K 4.9 0 BIAS OSC Q4504 KTC3203_Y 4.9 R4511 22K 220K 1/4W 0 4.8 0 AMP Q4506 2SC3052-T1 R4519 R4521 10M B B 22 KA 0 79 2.0 80
Vref 2.3V
Y-VCC
VHS
SOPB
FM AGC
PB FM EQ S-EQ
FM AGC FIL
Y-GND
4.7K
3
NORMAL_A FROM/TO HEAD AUDIO CONTROL P.CON+5V CP4502 IMSA-9604S-06C 6 5 4 3 2 1 AUDIO REC AUDIO PB CTL+ CTLAE HEAD(+) AE HEAD(-) 0 AUDIO PB SW Q4501 2SC3052-T1 TO FULL ERASE HEAD CP4503 B2013H02-2P 2 1 FE HEAD(GND) FE HEAD(HOT) GND HOT AUDIO PB SW Q4502 2SC3052-T1 0.7 0 0 CTL+ CTLV.REC_ST_H
24
REC FM-EQ
25
R4504 12K
2 2.3 B
3 2.2
4 2.2
5 2.5
6 2.3 C4541
7 2.2 0.0022 B
8 2.3 R4533
9 2.4 820
10 5.0
11 1.0
12 1.0
13 1.7 13
14 1.4
15
16 0
17 0 NC 1.5 C4551
18 0.1
19 2.2
20
R4520 0.1
TP4501
V.ENV
W846
0 5.3
R4509 680
C4571
820P CH KA
0.33 KA
R4540
39P CH
W804
100
50V 3.3
50V
C4557
6.3V
15
150P CH
R4501
C4548
L4504
C4553
220
C4539
0 0 B
C4527
25V 10 KA
C4511
4.7 R4516
R4510
0.0022
R4507
1M
0.0047
C4501
R4522
220
C4534_1
14
R4531
0.015
180
V.SYNC
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
G-9
G-10
(VCR PCB)
8
VIDEO_OUT B CENT_LED_CTL CONTROL_IN SCL CYL_DRIVE AT+5V SCL EEP ROM IC BR24L04F-WE2 IC199_1 5.0 8 VCC 0 7 WP 4.8 6 SCL C133 X101 15P CH 100DA32R01 C131 32.768KHz 15P CH C132 0.1 B SDA 4.8 5 SDA GND
8
FROM/TO REGULATOR H.SYNC V.SYNC VOL_PWM HIFI_H.SW SDA Y/C_VIDEO DVD_H C148 68P CH C145 CH C151 0.1 F
10P CH C135
150P CH
W859
C152
0.18
C137
5.6K
A0
A1
R134
10K
R138
330K
R132
56K
C126 27 FROM/TO Y/C/AUDIO/HEAD AMP 10V 100 KA C125 0.1 Y/C_VIDEO Y/C_CLK Y/C_DATA Y/C_CS H.SW VIDEO_OUT ENV_DET VCR_A_MUTE CTL+ CTLC_ROTARY DUMMY_V.SYNC V.REC_ST_H H.AMP_SW1 COMP VCR_A_MUTE C114 0.01 TV_POWER_H B R112 100
R129 1M
1 0 0
2 0
A2
33K 1/4W
25V 10
B R131
R111
C130
4.7K
1/4W
28 SW Q112 2SC3052-T1
C138
C129
KA
P.CON+5V
100P CH
C121
0.022
68P
3 0
R139
R141
R147
47K
C154
47K
0.001
DRUM_PWM
B NC NC NC NC NC NC 2.2 1.6 0 0 4.7 4.9 0 0 5.0 3.3 1.0 0 0 0 5.0 4.9 3.6 3.6 2.7 0 0 5.0 5.0 0 3.5 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 CAP_PWM CENT_LED_CTL DVD_H AV_SW2 HSYNC CAP_FULL OSCO VSYNC VDD NC NC XO CVIN VSS2 VSS OSCI NC NC CVIN2 SXI NC NC XI
R135
10K
10K
FROM/TO DVD IN/OUT B TX RESET DUMMY_V.SYNC R153 1K 1/4W R144 1K 1/4W R140 4.7K R143 R107 4.7K S101Y 4.7K H.SW IIC_OFF CAP_LIMIT TV_A_MUTE 16 H.SW TP102 NC RX DVD_RESET AV_SW1 FROM/TO IN/OUT
53
54
VCR.A.MUTE FSCLPF TV_POWER_ON-H VM_OSD_SW CYL_SPEED_UP BLK DEGAUSS R G B CAP_F/R CYL_FG/PG H_CTL FGF 98:C_ROTARY 99:H.AMP.SW1 100:COMP 76:CO CHROMA_POWER_ON_H 77: NC VCR_POWER_ON-H V.REC.START-H REC/OTR_LED SYSCON/TIMER/SERVO IC IC101 OEC8078A 51: VDD2 52: AFCC 25:RESET 24:DUMMY.V.SYNC
IIC_OFF CAP_LIMIT TV_MUTE TUNER_H SCL SDA TX RX TV/DVD_LED Y/C_DATA Y/C_CS Y/C_CLK RENT_H EXT_A_MUTE FF/REW_L AV_SW1 EXT_MUTE REMOCON IN REEL-S REEL-T TAB_SW
22
2.2K
AFCLPF
H.SW
0 0 5.0 0 NC 1.3
23
0.0022
R118
F 2.6
52
24
C116
C123
51
25
5.1 2.5
5.0 0.1 3.5 5.0 3.6 0 0 4.8 4.8 0 0 0 NC 5.0 0.1 5.0 0 0 NC 5.1 0 0
6
KEY_B KEY_A REC_LED T-REC_LED
56
55
C110
5
C107 D101 LTE-3271T-012A-O BOT SENSOR 5.0 Q101 ST-304L 0 C101 EOT SENSOR Q103 ST-304L B 5.0
63
13
OSDB 0.0047 CAP_F/R CYL_FG/PG R108 1K C109 EOT BOT R106 270K C113 1K 25V 10 B C111 KA C117 0.01 CTL+ B R110 C118 10K 0.001 B C122 10V 33 R115 560 R116 560 R103 R105 560 0.0039 B C119 25V 10 KA 17 H_CONTROL B
62
14
OSDG
61
15
OSDR
60
16
DEGAUSS_H
59
17
OSD_Y
2.2M
1/4W
58
18
CYL_DRIVE
R114
57
19
20
21
W841 W842
SCL SDA TX RX
REMOCON_IN TV_POWER_H
FROM/TO CHROMA/IF Y/C_DATA Y/C_CS Y/C_CLK OSD_R OSD_G OSD_B OSD_Y TV_POWER_H AV_SW Q116 2SC3052-T1 AV_SW1 R152 REEL-S REEL-T 22K V.SYNC H_CONTROL H.SYNC SDA REMOCON_IN SCL VCR_POWER_H PROTECT IIC_OFF EMERGENCY
64
0.001
65
0.001
67
66
10 8 7 5 4 6 9
11
12
68
69 70 71 72
VRO VRI AVSS CTLA EMERGENCY ST_SELECT AVDD MSSEN_B MSSEN_A LDM_CTL KEY_A KEY_B CTL(+) CTL(-) T-REC_LED
6.3V 100 KA
C102
73
ENV.DET
CENT_LED_CTL 4.9 0 C128 16V 220 YK R173 TAB SW SW101 TAB_SW LSA-1144EAU
PROTECT
DVD_RESET
0.2
HIFI_ENV
74
BOT
EOT
AFT
75
CTL-
76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 2.5 0 2.6 0.1 5.1 5.1 4.9 4.9 0 2.6 2.4 0 3.4 3.6 0 0 5.0 0 0.1 0 0 NC 0 3.5 4.9 0
W845 B
W806
C164
POWER_FAIL
270K
R120
560
R101
0.1
R171 CH C143 1K 220 YK BUFFER Q114 2SA1530A-T1 5.1 R119 2.2K 5.1 W883 R166 10K D106 POWER_FAIL 4.4 MTZJ12B-EIC HIFI_ENV HIFI_H.SW VCR_A_MUTE SDA SCL ST_SELECT
C120
0.027
R124
10K
16V 22 KA
C104
10K 1/4W
R128
VCR_POWER_H
16V 47 YK
6.3V
SW Q106 RT1N241C-T112-1
4.9
C146
22P
1K
1/2W
FROM/TO CAPSTAN DD UNIT C103 CP101 TMC-J12P-B2 1 2 3 4 5 6 7 8 9 CAP FG CAP VCO VCC CAP.M F/R I LIMIT MOTOR GND GND LD/CY VCO
0 MS_SEN-B MS_SEN-A
R137 C144 B V.REC_ST_H H.AMP_SW1 DVD_RESET C_ROTARY PROTECT 0.1 4.7K COMP
EMERGENCY
ST_SELECT
0 5.0 0
T-REC_LED
ENV_DET
LDM_CTL
HIFI_ENV
REC_LED
TAB_SW
KEY_A
KEY_B
EOT
AFT
BOT
SW Q110 RT1N141C
TO SOUND AMP/SURROUND R165 4.7K VOL_PWM TV_POWER_H OSD_R R159 4.7K TV_POWER_H FROM/TO DIGITAL COMB/FILTER COMB_GND SDA SCL AFT FROM/TO TV POWER GND DEGAUSS_H POWER_FAIL MOTOR_GND PCB010 DME069 TV_A_MUTE
R104 3.3K
0.1
C112
R125
10 11 12
0.1
1/4W
R133 REEL SENSOR Q108 RPI-303 D103 0 1 2 2.4 27K 1SS133 D102 C141
R122
MTZJ5.6B-EIC
47K
47K
NC
C106
6.8K
0.022
5.1 2 3
R136
1.2
6.3V
OUT 1 5.2
IN 2 5.1
GND 3 0
25V 47 YK
0.001 CH
0.001 CH R113
R109
33K C115
C124
33K
C136
B C139
0.9
1.4
0.5
4 0
5.1
5.1 0.1
D105
4 1.4
1SS133
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
G-11
G-12
(VCR PCB)
FROM CRT/OPERATION CP2201 (CD2251) A2001WV2-2P 2 1 GND KEY-B KEY_B
7
FROM/TO SOUND AMP/SURROUND T-REC LED SW Q2203 RT1N141C 0 3.9 0 REC/OTR D2205 POWER_LED_SW Q2202 RT1N141C 0 0 4.7 LTL-1CHEE-002A T-REC D2206 LTL-1CHEE-002A POWER D2207
R8005 LTL-1CHEE-002A
SOUND_R+ SOUND_L+ SP_OUT_R SP_OUT_L ZERO_MUTE_1 REC LED SW Q2201 RT1N141C 0 3.9
220
R8006 B8001 C8010 F R8004 68 1.5 1.7 D AUDIO DRIVER Q8002 2SC3052-T1 R8003 100K 5.1 R8013 1 2 H E W4BRH3.5X6X1.0X2 0.1 COAXIAL J8007 MSP-251V-05NI-FE-LF
270 1/4W
R2223
R2224
FROM REGULATOR
270
270
T-REC_LED
R2227
REC_LED
1/4W
1/4W
3.3K
1.5K
R8007
C8095 0.022 FROM/TO MICON R2205 KEY_B SW2201 EVQ21505R SW2202 EVQ21505R SW2203 EVQ21505R SW2204 EVQ21505R SW2205 EVQ21505R SW2206 EVQ21505R STOP/EJECT SW2207 EVQ21505R C2201 CH.DOWN KEY_A REC_LED REW T-REC_LED REMOCON_IN TV_POWER_H 4.7K R2201 3.9K PLAY R2203 1.8K R2204 1.2K REC/OTR R2206 820 R2208 560 D2201 B MTZJ6.8B-EIC 0.01 OS2201 ROM-V3138SR Vout R4215 4.7K R4219 5.0 D4207 1SS133 0 0 ZERO_SW Q4204 RT1N241C-T112-1 1K 1 C2205 100P CH CH.UP R2212 R2211 1/4W C8094 10V 100 YK L8002 100uH B
2.2K
FF
P.CON+5V
P.CON+5V_E
KEY_B
FRONT_V_IN
AT+5V
SPDIF-134
SOUND_R+
SOUND_L+
JACK_OUT
SP_OUT_L
100 YK
FROM DVD IN/OUT C4205 SW_AUDIO_OUT_R SW_AUDIO_OUT_L 25V 10 KA R4213 C4204 25V 10 KA 75 W971 NC 470P CH 7 6 2 C4211 16V 470 YK C2208 470P B C2209 W970 NC R2225
NC W813 W4BRH3.5X6X1.0
16V
R2226 100
SPDIF-134
100 1/2W
P.CON+5V_E ZERO
B2201
C2206
FRONT_A_IN_R
FRONT_V_IN
FRONT_A_IN_L
C2210
100 YK
NC
C2213
470P
CH
C2207
W934
100P
CH
R2202
2 1
2 1
C2202
2 1
470P
C2203
NC
NC
CH
NC
NC
NC
W886
470P
75
CH
W933
YELLOW
WHITE
RED
PCB010 DME069
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
G-13
G-14
100uH 0607
(W101)
W893
R626
0.047 B
C624
R636
5.6K
C632
0.1
C625
22K
X601
100CT3R532 3.579545MHz
Y/C_VIDEO-Y SW_C
0.1
C616
C631
0.1
0.1
8P
DVD_Y/C-Y TO Y/C/AUDIO/HEAD AMP V.SYNC CHROMA/IF_IC IC601 LA76319NM-MPB-E 49 0 SCL V.OUT TV_POWER_H AFC ACL NC H.OUT P.CON+5V EMERGENCY +B_DOWN OSD_G OSD_R 1K 1/4W R635 L604 W5T29X7.5X19 H.SYNC V.SYNC TEST POINT CP601 A2001WR2-4P 1 2 3 4 GND SCL SDA IIC_OFF SCL SDA IIC_OFF TV_POWER_H VCR_POWER_H R623 3.3K R632 4.7K 1/4W 5.0 0 SW Q606 0 2SC3052-T1 H.OUT P.CON+5V EMERGENCY OSD_Y OSD_B R630 1K SDA W810 W819 5.0 50 5.0 51 0 NC 5.0 NC 5.0 54 3.3 55 BUS TRAP 56 3.3 3.3 57 LPF ATT 0 58 NC 5.0 59 5.0 60 0 NC 2.53 NC 3.3 NC 0 NC OSD CONTRAST OSD SW ORIVE/OUT-OFF CLMP REG-SW RST 5V/8V-REG V/Y SW CL SHARP BS SG RGB MATRIX CLMP VXD 52 VIDEO SW AUDIO SW TINT APC1 FSC
4.7M
R620
R624
680K
C628 NC NC NC 0 0 0 4.9 NC 0 4.8 2.6 2.5 4.3 3.9 NC 2.6 NC3.6 NC 5.0 3.1 3.5 2.7 48 47 46 45 39 38 37 36 35 34 33 44 43 42 41 40 32 0.47 3.9 NC 0 2.7 30 2.5 CLMP HOR VCO 1/256 COLOP CLAMP SYNC SEP VER SEP VER C/D VER RAMP ABL/ACL HOR VCC HOR C/D FBP AFC1 AFC2 PHASE SHIFTER HOR OUT 29 0 28 AF SW 0 X-RAY 27 1.7 26 5.1 25 0 24 NC 1.5 23 2.6 22 5.2 21 2.4 20 3.1 62 19 3.1 63 18 0.47 B C611 0 64 17 5.0 MTZJ12B-EIC B D605 C614 0.33 KA C612 4.4 SW 9.0 Q605 RT1P141C-T112-1 R628 C613 10K B R616 330 1/4W C618 R617 0.015 B C619 1 B R627 2.2K R619 4.7K +-1% C622 1 B C601 0.01 B W827 R622 390 1/4W 33 DVD_Y/C-Y B
6
1 2 3 4 5 6 7 8 9
8P
REG SW
53
BPF
YC SN
ACC
CEMO
31
40 AFC H.OUT 39
CD602 CU291701
P.CON+8V
61
0 4.4
5.0
H_CONTROL
1/4W
0 FROM TV POWER
100
100
100
16V
8.6
2.5
3.4
2.5 NC
4.3
8.5
2.6
7.8 NC
3.4
3.4
3.5
100
10
11
12
13
14
15
16
R609
R610
C604
R611
36
37 38 V.OUT
W892
0.1
FROM/TO MICON PROTECT R603 EMERGENCY R612 V.SYNC H.SYNC VCR_POWER_H IIC_OFF OSD_Y R633 10K OSD_B OSD_G OSD_R SDA 1K 100 OUT 1 10.0 R634 1K 5.0 0 PROTECT Q602 0 2SC3052-T1 16V 100 KA 0 GND 2 12.0 IN 3
0.1
16V 100 KA
0.1 B C609
R607
MTZJ12B -EIC
MTZJ12B -EIC
C603
C606
C608
D601
D602
C634 1 B
27K
CD603 CU284501
2
L603 W5T29X7.5X19
NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
PCB010 DME069
G-15
G-16
+
1 6.6 2 3.5 3 0
4 3.5 5 3.9
L 6 1.3 7 0
10 3.5 11 0
+
12 3.5 R357
C328
HS351 763WAA0295
25V 10 KA
SOUND+B
18K
SOUND_GND R301
6
GND
2.7K
18
C357
FROM MICON R353 TV_POWER_H R359 56K 1/4W TV_A_MUTE 47K 1/4W VOL_PWM
W881
CD303 CH149006
W905
W925
W914
PCB010 DME069
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
G-17
G-18
(VCR PCB)
TUNER_AUDIO VCR_A_MUTE P.CON+5V SDA SCL FSC
C5511 0.1 B
L5504
W834
C5562
22uH 0305
C5563
C5507
R5504 YK 3.3K
50V 0.22
6.3V 47 KA
0.001
0.1
C5564
7
50V 10 YK C5542
C5522_1
R5519 50V 10 YK
YK
C5523
4.7
KA
C5528
33 KA
4.7
22K
50V
C5540
R5514
50V
27K
10V
C5544
R5523 C5504 0.1 B 1M R5503 3.9M C5509 0.1 F Hi-Fi/AUDIO/HEAD AMP/DEM IC IC5501 AN3663FBP 2.2 48 49 3.4 C5513 0.1 C5506 0.1 AUDIO_OUT_R 35V B C5510 0.1 B C5514 22 YK C5512 R5522 1K 55 0 1.2 C5515 L5501 100uH C5501 0.1 C5502 16V 47 YK NORMAL_A Y/C_AUDIO R5501 1.2K 1/4W R5502 330 C5503 0.047 B 2.3 C5520 C5518 B 0.6 C5508 50V 10 YK C5517 0.1 B B 35V 22 YK 4.3 11.0 4.3 NC 1.0 NC 2.4 2.3 2.2 B 51 4.9 2.5 4.2 2.3 2.7
6
C5505 16V L5502_1 P.CON+5V 22uH 0305 47 KA
0 4.9 41 40
0 NC 39
ZZ-PROM
0 1.6 38 37
0 2.4 0.7 2.4 36 35 34 33 32 2.4 C5550 2.1 50V 30 1.8 1.8 1.8 C5556 2.5 0 4.9 C5566 0.6 0 0.7 C5565 82P CH C5558 HF1 0.01 21 0 0 2.4 2.4 0.7 25V 10 KA
HA2
6
0.015 B FROM DIGITAL COMB/FILTER YK D5502 1SS133 28 HIFI_ENV 0.01 B 20 HIFI_H.SW C5549 0.1 F 0.1 B L5503 P.CON+5V C5559 6.3V 47 KA 82P CH 22uH 0305 C5560 HF2 0.01 23 F FROM/TO Y/C/AUDIO/HEAD AMP HIFI ENV. TP5501 NC V.REC_ST_H C5551 0.22
50
31
S/N PNR RCH SW12 SW NOISE SW9 MUTE FROM 1PIN R SW18 BS L NORMAL SW19 R MUTE L HIFI MIX SW16 MIX HIFI BS FROM 3PIN PC AUDIO LIMIT SW14 SW4 SW2 SW NOISE SW13 S/N PB LPF CURR AMP + RCH BPF FM UM LCH BPF SW10 NOISE DET LINER SW HA1 HOLD TIMING AUDIO LIMIT PC PB LPF PB RCH VCO REC LPF HPF REC SW21
TUNER_AUDIO
52
53
MATRIX
LOG AMP
AMP
50V 2.2 YK
OUTPUT SW R L AMP
54
5
ST_SELECT AUDIO_OUT_L P.CON+12V D5501 11EQS04
J
AN3672FBP
26
27
29
C5557
56
SW17 R
57
59
58
22
24
25
60
SW22 L
0.1 B 0.015 B
61
DET AGC
62
19
SW15 H SW11 L
20
NORMAL_A
63
18
C5555_1 64
VREF1
1 25V 10 KA 0
2 2.3 C5525
3 25V 10 KA 0
4 2.2
5 2.4
6 2.1
7 0.5
8 0
9 0
10 NC 0
11 2.0
13 0
14 0
15 2.4 NC
16
C5536
10V 33 KA
KA
C5530
C5545_1
C5534
0.022
17
25V 10 KA
50V 10
C5524
25V 10 KA
C5519
50V 3.3
C5526
KA
W926
YK
C5538
C5533
50V 10
C5529
3
R5506 390 R5507 390
0.1
50V 4.7 KA
C5531
C5543
680P CH
680P CH
50V R5518
R5510
C5521
C5527
8.2K
8.2K
R5508
56K 1/4W
R5509
R5525
3.3K
W872
FROM/TO TV POWER
1
NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK. NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
G-19
G-20
(VCR PCB)
TO Hi-Fi/DEMODULATOR
TUNER_AUDIO
W908
R1530
5
R1509_1 1K FROM/TO DEFLECTION 1 SW_C R1517 2.7K TO DVD DECK GND CD1705 CH012403 W840 C1525 B FROM DVD IN/OUT DVD_Y/C-C
W889
4
MONITOR TUNER 17 VIDEO OUT 15 AT+30V
20
115-V-KA35ARH
19
16 NC
10 CLOCK
11 DATA
9 NC
21
18
2.1
3.9
31.5
4.2
NC 0 NC 4.8
1.4
NC
NC
NC
NC
31
W837
NC
NC
C006
W829
W815
0.001
FROM/TO IN/OUT
C001 0.1 F
L001
TUNER_AUDIO
TUNER_VIDEO
100uH
W811
32
W937 Y/C_VIDEO
SDA
AFT
P.CON+5V
AT+30V
SCL
JACK_OUT
AUX_V[F/R]
PCB010 DME069
ARE
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
G-21
G-22
(VCR PCB)
TO SOUND AMP/SURROUND
7
W816 C8019 56P CH
W844
TX RX 25V
C8001 10 KA R8030
R8032 1K
7
AUDIO_OUT_L TO IN/OUT
P.CON+6V_DH P.CON+5V_D DVD+3.8V S801X S801Y 7.8 0 9.3 AUDIO SW IC IC8001 MM1502XNRE Vin1 GND Vin2 SW1 V OUT Vcc 6 1 4.4 8.6 12.4
1K
P.CON+5V_E ZERO SPDIF-134 SW_AUDIO_OUT_L SW_AUDIO_OUT_R SW_AUDIO_OUT_L L8001 P.CON+12V 16V 100 YK
3 4 5 6 7 8 9 10 11
100uH
0305
C8012
KA
0.1
C8013
C8006
25V 10
SPDIF-134 0 7.8 0 0.7 5 2 0.7 0 9.3 KA GND Vin2 V OUT Vcc 8.6 12.35 AUDIO SW IC IC8002 MM1502XNRE Vin1 SW1 6 1 4.37 25V
C8009 R8029 10 KA
R8031 1K 1K
AUDIO_OUT_R
TO CHROMA/IF DVD_Y/C-Y
5
FROM/TO MICON TX RX DVD_RESET AV_SW1 DVD_H
C8007
CP8002 (CP8101_3) IMSA-9604S-12C 12 11 10 9 CVBS GND C(CVBS) GND Y GND AUDIO-L GND AUDIO-R ZERO DVD RESET DVD_H
25V 10
C8014
FROM/TO AUDIO/VIDEO
0.1
C8015
AT+5V
8 7 6 5 4 3 2 1
P.CON+5V_E S809X ZERO DVD_RESET R8020 680 DVD_A_OUT_R 30 C8020 C8044 0.1 B R8021 680 W850 TO Y/C/AUDIO/HEAD AMP W916 29 DVD_A_OUT_L DVD+3.8V P.CON+5V_D P.CON+12V P.CON+6V_DH AT+5V S809Y FROM REGULATOR
100P CH R8028 1K
DVD_H DVD_VIDEO
W917
C8026
PCB010 DME069
NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
G-23
G-24
5.7 5.1
5.7
25V
6.6
D3008
W809
C3009
0.1
R3010
9.3
7.8 P.CON+8V SW Q3002 KTC3209_Y R3006 100 1/4W 10V 470 YK C3022
P.CON+8V FROM/TO MICON HS3002 763WAAA077 VCR_POWER_H AT+12V P.CON+5V_C DVD_H P.CON+5V_D OUT IC IC3001 KIA278R05PI P.CON+6V_D OUT IC IC3002 KIA278R06PI AT+5V BACKUP+5V P.CON+5V
18
1W 8.4
8.5VREG
IN 1 6.4
OUT 2 5.3
SW 4
OUT 2 6
GND 3 0
TO IN/OUT
5
AT+5V P.CON+5V
R3011
W835
S813X W938
S813Y
C3024
C3027
10
4
R3012 2.2 3W
0.1
0.1
B C3028
R3025 FROM/TO CHROMA/IF 15 2W DVD+3.8V 5.1 4.0 MTZJ4.7B-EIC D3003 BUFFER Q3001 2SC3052-T1 50V 1 KA 4.6 C3013 8.5VREG AT5.7VREG R3007 15K DVD_H P.CON+8V P.CON+5V P.CON+5V_C
2200 YK
C3010
6.3V
TO Hi-Fi/DEMODULATOR
3
1K R3019 P.CON+5V P.CON+12V 50V 4.7 KA
MTZJ33B-EIC
1 KA
MTZJ5.6B-EIC
D3001
D3002
C3007
C3016
1 KA
C3011
50V
+B
SW 0 Q3011 2SC3052-T1 0
TO DVD IN/OUT R3016 10K VCR_POWER_H AT+5V P.CON+12V DVD+3.8V P.CON+5V_D P.CON+5V_C P.CON+6V_DH
50V
0.7
12.3 13.0
2
R3021 22 1W P.CON+12V AT+30V PCB010 DME069
12.9
NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
G-25
G-26
FROM/TO MICON POWER_FAIL DEGAUSS_H D1719 D1702 1SS133 12.6 C1717_2 RELAY DRIVE Q1702 KTC3198 R1705 0 SR340-004 R1708 10K 1/4W 10K W4BRH3.5X6X1.0 B1703 MHE MTZJ12B-EIC D1732 MOTOR_GND GND TO SOUND AMP/SURROUND SOUND+B SOUND_GND (S811) RY1701 ALKS321_M60 2 3 CP1704 A1561WV2-2P TH1701 ZPB45BL3R0A 1 1/2W +-10% GND
16V 3300
R1726
7
0
1K 1/4W
TO CHROMA/IF
R1702
2.7M
D1723 2KV 0.0015 R R1718 FE201-6L49 200V 220 YXF C1705 FROM/TO IN/OUT SOUND_GND GND FROM/TO Hi-Fi/DEMODULATOR GND R1725 1/2W FROM/TO DIGITAL COMB/FILTER GND FROM/TO REGULATOR 0 D1713 10V 2200 YK 192.0 2KV 820P R C1731_1 0 0 18.0 10.4 C1732 C1727 500V 0.0033 B D1730 R1717 8.1 D1709 1SS133 R1731 R1714 17.6 4 0.4 3 D1737 0.22 MTZJ33B-EIC 1W R1715 150 C1709 180 1/4W B D1715 MTZJ18B -EIC R1721 SWITCHING Q1706 KTC3203_Y 0 330 2W 0.4 0.0027 B C1712 C1724 C1713_1 100V 0.047 MMTS 500V 0.001 B W928 D1707 21DQ09N-TA2B1 D1704 21DQ09N-TA2B1 C1718 0.0033 D1733 W821 1SS133 2200 YK S824X 1N4937-PAN 100 1/2W 50V 4.7 YK 4.7K 1/4W B D1722 R1703 R1727 NC FE201-6L49 D1712 21DQ09N C1728_1 D1734 21DQ09N
CP1707 003P-2100
CP1708 003P-2100
RM11C-EIC
7W R1722 1/2W
D1705
1/2W
AC120V_60Hz CD1702 09415910 BLADE WIDE R1701 CD1703 WHITE BLACK CD1704 BLACK
2.2M
W849
C1701
3 1
4 2 D1706
S822X
S822Y
RM11C-EIC
D1711
MTZJ18B-EIC
RM11C-EIC
1.5M
0 NC 14.1
L1704 W5T_20X10X10A
FH1701 EYF-52BCY
FH1702 EYF-52BCY
D1717
200V
56K
2KV 0.0022 B
2KV 0.0022 B
C1714
WHITE
680 USR
C1708
C1710
C1720
5
+B UNREG+5V MOTOR+12V UNREG+8V P.CON+12V GND FROM/TO DVD IN/OUT
6.3A 125V
25V 1000 YK
2KV 560P R
4
C1707
221.0 D S 0.1
MTZJ2.2B-EIC
4
GND
D1716 1N4937-PAN R1724 D1718 4.7K 1/4W C1715 680 1N4937-PAN 1/4W 25V 10 KA
0.0068
R1707
C1702 0.01 B
100 1/4W
S824Y
0.022
0.0056
R1712
R1716 3.3K
C1722
C1703
D1703
6.2
5.1
C1716
10K
C1733
25V
R1709
GND1
3.9K
REFERENCE
R1713
CATHOOLE
R1719
330
56K 1/4W
1/4W
ANODE
100
KX
1SS133
1SS133
2.5
2.8
1SS133
D1726
D1727
MTZJ6.8B-EIC
250V 0.0047
R1706
2.7K
C1711
D1721
1SS133
D1728
R1710
D1720
2
1SS133 D1724
CAUTION:
VR1701 10K METAL
+B ADJ
PCB010 DME069
REPLACE ONLY WITH THE SAME TYPE FUSE 6.3A 125V (F1701)
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE.
UNE PROTECTION CONTINUE LES RISQUES DINCEIE ATTENTION:POUR NUTILISER QUE DES FUSIBLE DE MEME TYPE 6.3A 125V (F1701)
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
G-27
G-28
(DEFLECTION PCB)
V.OUTPUT IC IC401 LA78040 + THERMAL PROTECTION AMP 20/W FB401_2 BSC27-N2265 5 12.0 6 25.0 7 4.0 R418 10V 100 YK 2.2K 1N4002-PAN C427 500V 22P SL D410 35V 100 YK MTZJ33B-EIC 1/4W C438_2 680 1/2W R450 680 1/2W 2.8 1 COL HV FROM/TO DY
VIDEO B+
F S GND 0 11 ABL
C423
D418
C429
R443
C414
21
C432
0.022
F R437
22 R447 560 1/2W R449 560 1/2W 100V 0.33 MKT 2.2K METAL VR404
R424 R428 50V 0.47 YK 820 1/4W 27K +-1% 10K 1/4W R421_1
R444
R432 MTZJ30B-EIC MTZJ6.8B-EIC 25V 2200 MHE 39K 1/4W C430 D413 D417 TO DVD DECK
7 8.1
560 1/2W
560 1/2W
R415
C443
C421
MTZJ30B-EIC
GND 8 E8 5 1.0 NC R454 1K 1W C449 2KV 0.001 R L403_2 250V 4.7mH 1 MHE
V801 A51AKL13X04(M)
R429
1/2W
HS402 763WAAA075
9 10 8 6 11
1.2K 1/2W
R G B 5 7 1
PMS
C402
CD807 CH012801
TO VCR DECK
R439
TO CRT
MPP
250V
C418_3
100 1/4W
B402
1 2 3 4 5 6 7 8
R427 R419
R414
+B +B NC GND GND GND P.CON+12V H.VOLT FROM/TO CHROMA/IF CP602B (CP602) A2001WV2-9P 1 2 3 4 5 6 V.OUT TV_POWER_H AFC ACL EW OUT H.OUT P.CON+5V EMERGENCY +B_DOWN AFC ACL NC NC
+B
NC
C405_1
HS401 763WAAA103
W822
W5RH3.5X5X1.0
23
24 T401_1 ETH14Y47AY 5 1 4
0.1
1.25KV 0.0056
2.8
C408_1
FROM TV POWER
B401 W5RH3.5X5X1.0
PHE
GND
68
C415 NC 0.001 B
R412
B403 W5RH3.5X5X1.0
26
1/2W
C412
0.43
50V 22 MHE
D404 1SS133
470 1/2W
R407
C407
W851
V.OUT R441
R406 2W
D403 1SS133
160V 47 BXA
D412 AU02A-EIC C436 500V 0.0022 B C446 D415 3W R445_3 AU02A-EIC 250V 22 MHE 180V NC NC GND HEATER GND HEATER
NC H.OUT P.CON+5V
R442
7 8 9
D402 AU02A-EIC
2 TP401 3 1 114.0 FROM/TO DIGITAL COMB/FILTER CP001 (CD002) 003P-2100 0 4 3.3K R440 10W C
0 4.9 0
100V 22 YK
GND
W807
C403
2.7
PCB080 CME029
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
G-29
G-30
R814 15K 2W 41 RED AMP Q802 KTC4217(O,Y) 7.8 D802 1SS133 7.3 W832 FROM CHROMA/IF CP603B (CP603) A2001WV2-8P 1 2 CUT OFF GND R.OUT G.OUT B.OUT CLAMP_OFF NC NC R810 220 1/4W GREEN AMP Q804 KTC4217(O,Y) 7.8 D801 1SS133 7.3 W833 3.0 GREEN AMP Q805 KTC3199_Y 2.4 R807 R818 220 1/4W R825 1.8K 1/4W 56 1/4W C801 100P CH 0 15K 2W 42 R821 2.7K 1/4W 123.9 W831 1.8K R806 R817 1/4W D805 1SS133 3.0 RED AMP Q803 KTC3199_Y 2.4 56 1/4W 220 1/4W R824 2.7K 123.5 7.3 R822 1/4W (10 MM)
CRT BLOCK
7
R805
220 1/4W
C815
680P
CH R815
3 4 5 6 7 8
7.3
117.0 0
1
0
NC
F
CRT SOCKET J801 ISHS62S
C817
D806 1SS133
560P
CH R816 15K 2W
W805
220 1/4W
7.3
4
D803 1SS133 W834 CC801 0 FROM DEFLECTION R808 R819 1.8K 1/4W D804 CP802B (CP802A) B2013H02-5P 1SS133 HEATER GND NC 180V NC 180V FROM/TO DEFLECTION 3.1 7.3 2.5 220 1/4W BLUE AMP Q807 KTC3199_Y 560P CH
C820
R809
56 1/4W
C816
W806
R826
ACCESSORY
5 4 3 2 1
HEATER GND
GND
GND GND
GND
PCB110 CCE024
(OPERATION PCB)
SCREEN
EVQ21505R
EVQ21505R
OPEN/CLOSE SW2251
EVQ21505R
EVQ21505R
EVQ21505R
EVQ21505R
EVQ21505R
EVQ21505R
VOL UP SW2253
SKIP SW2254
STOP SW2255
PLAY SW2256
SKIP SW2257
POWER SW2258
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
TO IN/OUT CD2251 CH220705 GND KEY-B (CP2201) 2 1
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
R2255 1K 1/4W
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
PCB270 CEE055
G-31
G-32
A
CP2301_1 T1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 FFC CLOSE GND(D) OPEN SLED,LOADING MOTOR LD+ LDFG SENSER 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 TT+ FF+
B
L4002
INTERCONNECTION DIAGRAM
8
CD4002_1 CP8001_1 1 2 3 4 5 6 7 8 9 10 11 GND(D) GND(D) TX RX GND(M) P.CON+6V P.CON+A5V DVD+3.8V DVD+3.8V GND(A) SPDIF 8 OHM SP351 8 OHM SP352 H5002 COMMAND TRANSMITTER TM101 FULL ERASE HEAD ASSY 1 2 3 4 5 6 7 8 9 10 11
T+ FF+ DVD DRIVE DM-3 MON(DVD) NC(SW) VOL(DVD) GND(DVD) LD(DVD) LD(CD) VOL(CD) GND(CD) MON(COM)
MON(DVD) NC(SW) VOL(DVD) GND(DVD) LD(DVD) LD(CD) VOL(CD) GND(CD) MON(COM) DVD/CD RF C B
GND(D) GND(D) SSCCLK/TX RDY(I/O(0))/RX GND(M) P.CON+6V P.CON+A5V P.CON+3.8V P.CON+3.8V GND(A) SPDIF
7
OPTICAL PICK-UP
7
HALL SENSOR MAIN COIL ROTOR MAGNET MR FG SENSOR VCC
SPEAKER
GND
C(CVBS) GND Y GND AUDIO-L GND AUDIO-R ZERO DVD RESET EXT_MUTE
3 4 5 6 7 8 9 10 11 12
3 4 5 6 7 8 9 10 11 12
10 9 8 7 6 5 4 3 2 1
10 9 8 7 6 5 4 3 2 1
CD2251
GND
11
11
GND
CD303
OS2201 CP4503 1 Vout 1 2 CP101 1 2 3 4 5 6 CAP_FG CAP_VCO VCC CAP.M F/R I_LIMIT MOTOR GND GND LD/CY_VCO CAP_CTL LDM CTL CYL_FG/PG CYL_CTL 1 2 3 4 5 6 7 8 9 10 11 12
KEY-B
GND
SOUND L+
SOUND R+
SOUND L-
SOUND R-
GND 2 B+ 3
1 2 3 4 5 6
SP1+ SP1SLD+ SLDLIMIT SW SW(GND) DVD PCB PCB130 DME060 CP601 1 2 3 4 GND SCL SDA IIC_OFF
FE HEAD(GND)
FE HEAD(HOT)
AUDIO-R
CP2201
CP303
CVBS
12
12
CVBS
KEY-B
CP8101_3
CP8002
HEADPHONE_JACK J2201
FE HEAD (GND)
FE HEAD (HOT)
CD8101 FFC
SPEAKER
GND
7 8 9 10 11 12
5
1 2 3 4 5 6 7
RED FFC CP001 GND 1 CP602B V.OUT TV_POWER_H AFC ACL 1 2 3 4 5 6 7 9 CD604 CD602 CD002 1 CP602 1 2 3 4 5 6 7 8 9 H.OUT P.CON+5V EMERGENCY +B_DOWN MONITOR TUNER TU001 CP4501 HF1_(R) HF_COM HF2 (L) SP-CH1 (R) 15 AT+30V 14 SIF OUT NC H.VOLT 13 AUDIO OUT 12 AFT OUT CD603 4 3 NC 2 1 CP603 1 2 3 4 ANODE 5 6 7 8 CRT H.V DEGAUSS COIL L1703 1 L603 CUT_OFF GND R.OUT G.OUT B.OUT CLAMP_OFF NC NC 8 NC 7 NC CP4502 AUDIO REC AUDIO PB CTL+ CP1704 1 2 YELLOW FRONT VIDEO JACK WHITE BLACK AC120V_60Hz CD1702 CD1703 WHITE CD1704 BLACK E J2202 COAXIAL J8007 H 1 2
H
5 5 D-W OUT
6 6 D-V OUT
V.OUT D-PG GND D-PG OUT AFC ACL D-U OUT M-GND TV_POWER_H L604 D-COM
GND
4
UN4001 CYLINDER UNIT ASSY CD4501 FFC 9 8 7 6 5 4 3 2 1 9 8 7 6 5 4 3 2 1 EP/LP HEAD 11 DATA 10 CLOCK NC 9 NC HEAD AUDIO CONTROL ASSY H5001 FFC 6 5 4 3 2 1 6 5 4 3 2 1 6 5 4 3 2 1 AUDIO REC AUDIO PB CTL+ CTLAE HEAD(+) AE HEAD(-) AE CONTROL AUDIO 6 5 4 3 2 1 SP HEAD HI-FI HEAD
21
20
17 VIDEO OUT NC 16 NC
9 8 7 6 5 4 3 2 1
FBT FB401_2
3
CP802A 180V GND
FOCUS SCREEN
CP802B
CP804
FOCUS
2
10 11 1 9
SCREEN
6 NC 5 NC 4 NC 3 +B
CP603B F BLADE WIDE CUT_OFF GND R.OUT G.OUT B.OUT CLAMP_OFF 1 1 2 3 4 5 6 7 8 L1704
NC
2 1
NC
2 1
NC
2 1
NC
NC NC
18
2 NC 1 NC
19
GND
GND
GND
GND
CP805
CP803
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
CD1705
TO DVD DECK
NOTE: THIS INTERCONNECTION DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
CD805
2 CD803
G-33
G-34
WAVEFORMS
MPEG/MICON/DSP
10ns 100mV
AUDIO/VIDEO
500s 500mV
Y/C/AUDIO/HEAD AMP
PB 20s 1.0V
11
5ns 20mV
500s 500mV
PB 20s 1.0V
12
20ns 1.0V
10s 100mV
PB 1ms 1.0V
13
200ns 1.0V
100s 200mV
PB 5ms 2.0V
14
MEMORY
5ns 500mV 10s 200mV PB 20s 20V
10
15
NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
H-1
WAVEFORMS
MICON
PB 20ms 2.0V
DEFLECTION
10ms 10V
DEFLECTION
20s 200V
16
21
26
MICON
PB 1ms 2.0V 10ms 10V POWER ON 50s 2.0V
17
22
27
SOUND AMP/SURROUND
POWER ON 1ms 200mV 50s 10V POWER ON 10ms 2.0V
18
23
28
DEFLECTION
10ms 0.5V 50s 5.0V
DVD IN/OUT
PB 1ms 2.0V
19
24
29
Hi-Fi/DEMODULATOR
POWER ON 1ms 1.0V
CHROMA/IF
POWER ON 20s 0.5V PB 1ms 2.0V
20
25
30
NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
H-2
WAVEFORMS
DIGITAL COMB/FILTER
POWER ON 20s 0.5V POWER ON 20s 1.0V
CRT/OPERATION
20s 50V
31
36
41
20s 50V
32
37
42
CHROMA/IF
POWER ON 20s 0.5V POWER ON 10ms 1.0V 20s 50V
33
38
43
34
39
35
40
NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
H-3
202
111
118
202
202
102B
202
208
131
102 113 201
102A
202
102B
201
131
131
131 201
101K
212 212 134 101K 101C 101E 212 212 212 101J
101I
101D
212
212 133
101K 101G
212
212
101H
212
101K 101G
101A
101
117
I1-1
208
204
123
126
120
208 208
204 115
208
209 114
214
124 125 208 108 105 104 104 208 110 205 213 213
213
205 110
106
121
109
116
129
130
203
208 126
206
128
208 211
208 126 208
208
132
127
203
122
I1-2
503
UN4001
334
333 501 H5002 314 336 324 315 323 503 335 342
504
H5001
317
341
306
331 508 508 322 312 305 301 AA 313 AA 332 AB AB AB CD1502 AA AA
AD
AC AB 307 AC
AB
506
345 302
507
318 AB
321
AB
510
AE AE
AB
CLASS GREASE
PART NO.
Y315061000 Y315071000 Y31D011000 Y315041000 Y315141000
PART NAME
MARK AA AB AC AD AE I2-1
NOTE: Applying positions AA, AB, AC, AD and AE for the grease are displayed for this section. Check if the correct grease is applied for each position.
M2001
320
300
502
CD1502 338 AA 337 AA 509 308 344 327 343 326 328
AA AD 502
AA 339 AA
AA
502 AA
AA
AB
340
AA
AB
AB
AA
505 330
CLASS GREASE
PART NO.
Y315061000 Y315071000 Y31D011000 Y315041000 Y315141000
PART NAME
MARK AA AB AC AD AE
NOTE: Applying positions AA, AB, AC, AD and AE for the grease are displayed for this section. Check if the correct grease is applied for each position.
I2-2
611
600
607
AB
SW1
705 617
CD2301
701
604 CD2302
616
702
605
CLASS GREASE
PART NO.
Y315061000 Y315131000
PART NAME
G-555G
SF-112
MARK AA AB
NOTE: Applying positions AA and AB for the grease are displayed for this section. Check if the correct grease is applied for each position.
I3-1
PART NO.
7A701A528A 701WPJD127 712WPBA146 712WPJC184 713WPA0292 735WPAA614 735WPAA748 735WPBB460 735WPBB461 743WKA0037 743WKA0043 800WQ0A052 7235630001 7A702A050A 702WPAA747 800WQ0A092 701WPA0686 701WPA0751 752WSA0230 8965TS1017 752WSA0308 753WUAA006 755WPAA033 85OP700038 726000A123 761WPA0223 741WUA0021 753WUA0069 755WPAA012 761WSAA023 723000D020 722A08A166 762WPA0011 752WSAA122 752WSA0292 752WSAA126 752WSA0489 752WSAA080 752WSA0327 8995034000 774WPA0005 899HV3T000 7250000596 744WUA0013 769WSAA012 899EFBA002 752WSAA083 723000C727
DESCRIPTION
FRONT CABI ASS'Y CABINET,FRONT FLAP,DVD FLAT,FLAP GLASS,LED HOLDER FLAP STOPPER,BUTTON BUTTON,FRAME 1 BUTTON,FRAME 2 SPRING FLAP SPRING,FLAP-DVD FELT SHEET SHEET DVD(NEW) BACK CABI ASS'Y CABINET,BACK FELT SHEET HOLDER DECK HOLDER DECK SHIELD CASE HEAD AMP CUSHION SHIELD,COVER HEAD AMP SPRING EARTH HEAD AMP COVER PCB HOLDER END SENSOR SHEET CRT SERVICEMAN HOLDER FBT SPRING EARTH SPRING EARTH PLATE COVER LIGHT (L) ANGLE,DECK SHEET DTS (S) SHEET RATING HOLDER CRT WIRE SHIELD,COVER DECK SHIELD AV JACK PLATE BOTTOM DVD,TOP VCR,TOP SHIELD,COVER FPC CORD CLIP UL CO. HOLDER WIRE-2 HOLDER ANODE WIRE SHEET,PC SPRING,EARTH WASHER CRT T=0.5 WIRING-CLIP ANGLE,FRONT SHEET CAUTION
REF. NO.
201 202 203 204 205 206 207 208 209 210 211 212 213 214 -----------------------
PART NO.
8141J50C5U 8117540A6U 811754080U 8109130B9U 8109I30A0U 8107630A8U 810963080Q 810923080U 811022680U 810763080U 810723040U 811063080U 810F13080U 810723060U 791WHAA113 791WHAA134 792WHA0537 792WHAA136 793WCDD148 795WCDA019 A5V404J975 J3T10902A J5V40401A J5V40410A JA5N0300
DESCRIPTION
SCREW TAP TITE(P) SCREW TAP TITE(B0) SCREW TAP TITE(B0) SCREW TAP TITE(B)R SCREW TAP TITE(B) SCREW,TAP TITE(S) SCREW TAP TITE(B) SCREW TAP TITE(B) SCREW TAP TITE(P) SCREW TAP TITE(S) SCREW TAP TITE(S) SCREW TAP TITE(P) SEMS(F) SCREW TAP TITE(S) FILM,BAG LIGHTRON SHEET PACKAGE,TOP PACKAGE,BOTTOM GIFT BOX PAD INSTRUCTION BOOK KIT WARRANTY SHEET INSTRUCTION BOOK(E) INSTRUCTION BOOK(S) POLYBAG INSTRUCTION GW22 TRUSS TRUSS PAN WH7 BRAZIER BRAZIER BIND BIND BRAZIER BIND BRAZIER BIND 5x35 HEXAGON 4x16 4x8 3x29 3x10 3x18 3x8 STAINLESS 3x8 2.6x8 3x8 3x4 3x8 3x8 3x6
65TS10-10(17.5x20x14)
J1-1
PART NO.
A5W9014420A 85OA400245 85OP900744 85OP200290 85OP600581 85OP500091 85OP800324 85OA000528 85OA200089 85OA200092 85OA300068 85OA300070 85OA400223 85OA400249 85OA400248 85OA400231 85OA900234 85OP900745 85OP700035 85OP900755 85OP400554 85OA900233 85OP000496 85OP200316 85OP200317 85OP200308 85OP200311 85OP200312 85OP200313 85OP300194 85OP400490 85OP400492 85OP400520 85OP400542 85OP400533 85OP600573 85OP600584 85OP600577 85OP600578 85OP600585 85OP600582 85OP800322 85OP800360 85OP800355 85OP800356 85OP900754 DECK ASSY
DESCRIPTION
A5W9014420A
REF. NO.
501 502 503 504 505 506 507 508 509 510 CD1501 CD1502 H5001 H5002 ! M101 ! M2001 M2003 ! UN4001
PART NO.
810722680U 83ETW3000U 810722640U 810212060U 810912660U 810A13040U 810A12650U 82Q264713N 82P184505N 810722660U 122H071704 122Y021002 1523Q91003 1543Q02014 1596S98002 1510S98044 1589S11025 A5T7016500
DESCRIPTION
SCREW,TAP TITE(S) BIND E-RING SCREW,TAP TITE(S) BIND SCREW,PAN SCREW,TAP TITE(B) PAN SCREW/WASHER(A) SCREW/WASHER(A) POLYSLIDER WASHER POLYSLIDER WASHER(CUT) SCREW TAP TITE(S) BIND CORD JUMPER CORD JUMPER HEAD (AUDIO CONTROL) HEAD (FULL ERASE) MOTOR,LOADING CAPSTAN DD UNIT MICRO MOTOR CYLINDER UNIT ASS'Y M2.6x8 3 M2.6x4 M2x6 M2.6x6 M3x4 M2.6x5 2.6x4.7xT0.13 1.8x4.5xT0.5 2.6x6 2H071704 2Y021002 VTR-1X2RPE22-756 VTR-1X2ERS11-154 MDB2B66B F2QVB73B I20AL34K A5T7016500
PINCH ROLLER BLOCK VA2 LEVER,FLAP BELT,CAPSTAN (S) WORM BASE,AC HEAD SPRING,AC HEAD MAIN CHASSIS ASS'Y CLUTCH ASS'Y ARM IDLER ASS'Y LOADING ARM S UNIT LOADING ARM T UNIT INCLINED BASE T UINT 3S P5 ARM ASS'Y 2 TENSION ARM ASS'Y 2 INCLINED BASE S UNIT CASS HOLDER ASS'Y CASS,OPENER REFLECTOR,LED BRACKET,TOP 3V HOLDER,CAPSTAN LINK UNIT POST,CASS GUIDE REEL,S (S) REEL,T (S) GEAR,IDLER GEAR,CLUTCH GEAR,COUPLING LEVER,CLUTCH GEAR,MAIN LOADING LEVER,TENSION HOLDER,TENSION CAP.P4 BAND,TENSION CONNECT,TENSION ARM,BRAKE T BAND,BRAKE T CAM,PINCH ROLLER CAM,MAIN ROD,MAIN GEAR,JOINT SPRING,TENSION SPRING,BRAKE T SPRING,COUPLING SPRING,RING LEVER,LINK
J2-1
PART NO.
A2I301H650 92P100109A 92P100094A 92P100088A 92AAA0013A 92P200013A 92P200014A 92SBB0029A 92P100095A 92P100097A 92P100096A 92P200012A 92P000014A 92P100093A 92P100091A 92P100092A 92P100089A 92P100090A 92P300020A 800WFAA008 811022680U 814011723U 816112080U 814011730U 811022080U 122H4O1901 122J4O1903 122H062102 122H052601 1515S98003 1596S18003 A5M4016610 A5N813W640 0515S32002 0500101037
DESCRIPTION
DVD MECHA ASS'Y HOLDER,TRAVERSE CLAMPER GEAR,MOTOR FEED RACK ASS'Y INSULATOR(F) INSULATOR(R) LOADER SUB ASS'Y GEAR,PULLEY PULLEY,MOTOR GEAR,MAIN BELT,LOADING PLATE,CLAMPER RACK,LOADING FRAME,MAIN TRAY RACK,FEED 1 RACK,FEED 2 SPRING,RACK FEED CUSHION C SCREW TAP TITE(P) BIND SCREW,PAN SEMS.TAP TITE(P) PAN SCREW,PAN SCREW,TAP TITE(P) BIND CORD JUMPER CORD JUMPER CORD JUMPER CORD JUMPER FEED MOTOR MOTOR,LOADING PCB ASS'Y PCB ASS'Y SWITCH PUSH SWITCH 2.6x8 M1.7x2.3 P3 W10 2x8 M1.7x3 P3 2x8 2H4O1901 127000-2928 2H062102 2H052601 BCZ3B03B BCZ3B52B DED003A DED002B SSS-13-2 ESE22MH24 or A2I301H650
J3-1
PART NO.
R4K1T4562F R4X5T6562F R4X5T6153F R4X5T6153F R3X28A181J R65582680J R3X28A181J R002T2010J R5X34F2R7J R5X34F332J R3X28B2R7J R3K581102J R3X18A153J R3X18A153J R3X18A153J R002T2155J R0G3K2275K R002T4272J R3X181R22J R3X28A331J R5X2CE1R2J R63881R22J R002T2563J R3X181180J R3X28B2R2J R3X181220J R3X28A150J E02LF3222M E02LU8220M E62DFB470M P4N8FJ562H P4J7F3434J P4J8F3434J P4G8FJ682H E02LU4101M E5EZF3222M E5EZF4102M E5EZFD220M C03L0R713K C0PLRR713K C0JBB0713K P2122B334M C03L0R7E3K C03L0R7S2K C0JBB07H3K C0JBB07H3K CD39E0MQ3M E52DHC681M E02L03222M E5EZF2332M E62NFC221M E02L01222M C03L0R7W2K E02L03102M E02LU54R7M 0010E00330 D1VT001330 D9WU05R62B D97U05R61B D1VT001330 D9WU01202B D97U01201B D1VT001330 D2WTAU02A0 D1VT001330 D1VT001330 D9WU05R62B D97U05R61B D2MXN40020 D2WT011E10 D9WU05R62B D97U05R61B D2WTAU02A0 D9WU03002B D97U03001B
DESCRIPTION RESISTORS
R,METAL R,METAL R,METAL R,METAL R,METAL R,FUSE R,METAL RC R,CEMENT R,CEMENT R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE RC RC RC R,METAL OXIDE R,METAL OXIDE R,CEMENT R,FUSE RC R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE 5.6K OHM 1/4W 5.6K OHM 1/6W 15K OHM 1/6W 15K OHM 1/6W 180 OHM 2W 68 OHM 1/2W 180 OHM 2W 1 OHM 1/2W 2.7 OHM 10W 3.3K OHM 10W 2.7 OHM 3W 1K OHM 1W 15K OHM 2W 15K OHM 2W 15K OHM 2W 1.5M OHM 1/2W 2.7M OHM 1/2W 2.7K OHM 1/4W 0.22 OHM 1W 330 OHM 2W 1.2 OHM 7W 0.22 OHM 1W 56K OHM 1/2W 18 OHM 1W 2.2 OHM 3W 22 OHM 1W 15 OHM 2W or
REF. NO.
D414 ! D415 D416 D417 D418 D601 D602 D603 D605 D801 D802 D803 D804 D805 D806 D1702 D1703 ! ! ! ! D1704 D1705 D1706 D1707 D1709 ! D1710 ! D1711 D1712 ! D1713 D1715 D1716 D1717 ! D1718 ! D1719 D1720 D1721 ! D1722 ! D1723 D1724 D1726 D1727 D1728 D1730 D1732 D1733 ! D1734 D1737 D2201 D2205 D2206 D2207 D2303 D2304 D3001 D3002 or D3003 or D3004 D3005
PART NO.
D9WU03002B D97U03001B D2WTAU02A0 D2WXN40050 D9WU06R82B D97U06R81B D9WU03302B D97U03301B D9WU01202B D97U01201B D9WU01202B D97U01201B D9WU01202B D97U01201B D9WU01202B D97U01201B D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D9WU02R72B D97U02R71B D28T21DQN9 D2WTRM11C0 D2WTRM11C0 D28T21DQN9 D1VT001330 D2WTRM11C0 D2WTRM11C0 D9WU02R22B D97U02R21B D28T21DQN9 D9WU01802B D97U01801B D2MXN49370 D2WXN49370 D9WU01802B D97U01801B D2MXN49370 D2WXN49370 D2LKSR3400 D2LKB340L0 D1VT001330 D1VT001330 D2MXN49370 D2WXN49370 D2CF2016L0 D1VT001330 D1VT001330 D9WU06R82B D97U06R81B D1VT001330 D2CF2016L0 D9WU01202B D97U01201B D1VT001330 D28T21DQN9 D9WU03302B D97U03301B D9WU06R82B D97U06R81B 0021E2Q140 0021E2Q140 0021E2Q140 DD7R0S3550 DD7R0S3550 D9WU03302B D97U03301B D9WU05R62B D97U05R61B D9WU04R72B D97U04R71B D2WXSB1400 D28TEQS040
DESCRIPTION DIODES
DIODE ZENER DIODE,ZENER DIODE SILICON DIODE SILICON DIODE ZENER DIODE,ZENER DIODE ZENER DIODE,ZENER DIODE ZENER DIODE,ZENER DIODE ZENER DIODE,ZENER DIODE ZENER DIODE,ZENER DIODE ZENER DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE ZENER DIODE,ZENER DIODE SCHOTTKY DIODE SILICON DIODE SILICON DIODE SCHOTTKY DIODE,SILICON DIODE SILICON DIODE SILICON DIODE ZENER DIODE,ZENER DIODE SCHOTTKY DIODE ZENER DIODE,ZENER DIODE,FAST RECOVERY DIODE SILICON DIODE ZENER DIODE,ZENER DIODE,FAST RECOVERY DIODE SILICON DIODE SCHOTTKY DIODE SCHOTTKY DIODE,SILICON DIODE,SILICON DIODE,FAST RECOVERY DIODE SILICON DIODE SILICON DIODE,SILICON DIODE,SILICON DIODE ZENER DIODE,ZENER DIODE,SILICON DIODE SILICON DIODE ZENER DIODE,ZENER DIODE,SILICON DIODE SCHOTTKY DIODE ZENER DIODE,ZENER DIODE ZENER DIODE,ZENER LED LED LED DIODE SILICON DIODE SILICON DIODE ZENER DIODE,ZENER DIODE ZENER DIODE,ZENER DIODE ZENER DIODE,ZENER DIODE SCHOTTKY DIODE,SCHOTTKY MTZJ30B-EIC MTZJ30B T-77 AU02A-EIC 1N4005-EIC MTZJ6.8B-EIC MTZJ6.8B T-77 MTZJ33B-EIC MTZJ33B T-77 MTZJ12B-EIC MTZJ12B T-77 MTZJ12B-EIC MTZJ12B T-77 MTZJ12B-EIC MTZJ12B T-77 MTZJ12B-EIC MTZJ12B T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 MTZJ2.7B-EIC MTZJ2.7B T-77 21DQ09N-TA2B1 RM11C-EIC RM11C-EIC 21DQ09N-TA2B1 1SS133T-77 RM11C-EIC RM11C-EIC MTZJ2.2B-EIC MTZJ2.2B T-77 21DQ09N-TA2B1 MTZJ18B-EIC MTZJ18B T-77 1N4937-PAN 1N4937 MTZJ18B-EIC MTZJ18B T-77 1N4937-PAN 1N4937 SR340-004 SB340L-6737 1SS133T-77 1SS133T-77 1N4937-PAN 1N4937 FE201-6L49 1SS133T-77 1SS133T-77 MTZJ6.8B-EIC MTZJ6.8B T-77 1SS133T-77 FE201-6L49 MTZJ12B-EIC MTZJ12B T-77 1SS133T-77 21DQ09N-TA2B1 MTZJ33B-EIC MTZJ33B T-77 MTZJ6.8B-EIC MTZJ6.8B T-77 LTL-1CHEE-002A LTL-1CHEE-002A LTL-1CHEE-002A 1SS355 TE-17 1SS355 TE-17 MTZJ33B-EIC MTZJ33B T-77 MTZJ5.6B-EIC MTZJ5.6B T-77 MTZJ4.7B-EIC MTZJ4.7B T-77 SB140-EIC 11EQS04TA1B2 or
or or or or or or
or
CAPACITORS
C321 ! C403 C404 ! C408 ! C412 ! ! ! ! ! C418 C429 C430 C434 C446 C449 CE CE CE CMPP CMPP CMPP CMPP CE CE CE CE CC CC CC CMP CC CC CC CC CC CE CE CE CE CE CC CE CE 2200 UF 25V 22 UF 100V 47 UF 160V 0.0056UF 1.25KV 0.43 UF 250V PMS or 0.43 UF 250V PME 0.0068UF 1.25KV PHE 100 UF 35V 2200 UF 25V 1000 UF 35V 22 UF 250V 0.001 UF 2KV R or 0.001 UF 2KV R 0.001 UF 2KV B 0.33 UF 275V ECQUL 0.0015UF 2KV R 560 PF 2KV R 0.0022UF 2KV B 0.0022UF 2KV B 0.0047UF 250V 680 UF 200V 2200 UF 25V 3300 UF 16V 220 UF 200V 2200 UF 10V 820 PF 2KV R 1000 UF 25V 4.7 UF 50V
or
or or or or or
C820 ! C1701 C1705 C1707 ! C1708 ! C1710 ! C1711 ! C1714 ! C1716 ! C1717 ! C1720 ! C1728 C1731 ! C1732 ! C1733 D101 D102 D103 D105 D106 D108 ! D402 ! D403 D404 ! D408 D410 D411 ! D412 D413
or
or
DIODES
INFRARED LED DIODE,SILICON DIODE ZENER DIODE,ZENER DIODE,SILICON DIODE ZENER DIODE,ZENER DIODE,SILICON DIODE SILICON DIODE,SILICON DIODE,SILICON DIODE ZENER DIODE,ZENER DIODE,FAST RECOVERY DIODE SILICON DIODE ZENER DIODE,ZENER DIODE SILICON DIODE ZENER DIODE,ZENER LTE-3271T-012A-O 1SS133T-77 MTZJ5.6B-EIC MTZJ5.6B T-77 1SS133T-77 MTZJ12B-EIC MTZJ12B T-77 1SS133T-77 AU02A-EIC 1SS133T-77 1SS133T-77 MTZJ5.6B-EIC MTZJ5.6B T-77 1N4002-PAN 11E1-EIC MTZJ5.6B-EIC MTZJ5.6B T-77 AU02A-EIC MTZJ30B-EIC MTZJ30B T-77
or
or
or or
or
or or
or or or
J4-1
PART NO.
D2MXN40020 D2WT011E10 D28T21DQN9 D28T21DQN9 D28T21DQN9 DD7R0S3550 DD7R0S3550 DD7R0S3550 DD7R0S3550 DD7R0S3550 D1VT001330 D28TEQS040 D1VT001330 DD7R0S3550 DD7R0S3550 I51F58078A I9UF032310 A5V404J015 I0FSP7522N I03TD80400 I03FC319N0 I1KF98L090 000220002W I1KJ9A431A I03FV65650 I1KA78R050 I1KA98R060 I1KA78R050 ICQK068621 I07F9E00W0 S5V405JF02 IF9J0161A7 ICLJ0610EX I03F3205M0 I01F63FBP0 I0UF015020 I0UF015020 I17F017530 0000M00390 TNRAC05003 0000M00390 0002700680 0002700680 TNRAC05003 0002700690 0002700690 TNRAB05004 T8RA030520 TCAA3875SY T6RA015300 T8RA030520 TCAA3875SY T8RA030520 TCAA3875SY TNRAD05002 TCAT03227Y TDUU024990 TNATB03005 TCAT032070 TA3T016240 TNRAB05004 T8RA030520 TCAA3875SY TPRAB05002 T8RA030520 TCAA3875SY TCA0042170 TC3F042170 TCATC3199Y TCA0042170 TC3F042170 TCATC3199Y TCA0042170 TC3F042170 TCATC3199Y
DESCRIPTION DIODES
DIODE,FAST RECOVERY DIODE SILICON DIODE SCHOTTKY DIODE SCHOTTKY DIODE SCHOTTKY DIODE SILICON DIODE SILICON DIODE SILICON DIODE SILICON DIODE SILICON DIODE,SILICON DIODE,SCHOTTKY DIODE,SILICON DIODE SILICON DIODE SILICON 1N4002-PAN 11E1-EIC 21DQ09N-TA2B1 21DQ09N-TA2B1 21DQ09N-TA2B1 1SS355 TE-17 1SS355 TE-17 1SS355 TE-17 1SS355 TE-17 1SS355 TE-17 1SS133T-77 11EQS04TA1B2 1SS133T-77 1SS355 TE-17 1SS355 TE-17 OEC8078A PST3231NR BR24L04F-WE2 AN7522N LA78040 LA76319NM-MPB-E KIA78L09F-RTF/P PS2561AL1-1-V(W) KIA431A-AT LA6565VR-TLM-E KIA278R05PI KIA278R06PI KIA278R05PI ZR36862PQCG-B BA33E00WHFP-TR
SST39VF1601-70-4C-EKE
REF. NO.
or Q1702 ! Q1705 ! Q1706 Q2201 Q2202 Q2203 Q2301 Q2302 Q2303 Q2304 Q2305 Q3001 ! Q3002 ! Q3003 ! Q3007 Q3010 Q3011 ! Q3014 Q3015 Q4004 Q4204 Q4501 Q4502 or Q4503 Q4504 Q4505 Q4506 Q4507 Q4509 Q4511 Q8002 Q8006 Q8007 L001 L402 L403 L601 L602 L603 L604 ! L1701 ! L1703 L1704 L3002 L4001 L4002 L4502 L4504 L4505 L4506 L4509 L5501 L5502 L5503 L5504 L8001 L8002 L8003 L8102 L8103 L8104 T401 ! T1701
PART NO.
TCATC31980 TJXG10NK50 TCAT032034 TNRAB05004 TNRAB05004 TNRAB05004 T67J1036K0 T67J048TL0 T8RA030520 TCAA3875SY T8RA030520 TCAA3875SY T8RA030520 TCAA3875SY T8RA030520 TCAA3875SY TCAT03209Y TCAT03209Y TAAT01281Y TCAT03209Y T8RA030520 TCAA3875SY TCAT03209Y T8RA030520 TCAA3875SY T8RA030520 TCAA3875SY TNRAC05003 T8RA030520 TCAA3875SY T8RA030520 TCAA3875SY TPRAC05003 TCAT032034 TAATA12660 T8RA030520 TCAA3875SY T8RA030520 TCAA3875SY T6RA015300 T6RA015300 T8RA030520 TCAA3875SY T8RA030520 TCAA3875SY TNRAC05003 021673101J 022100027A 021L75472J 02167F101J 02167D101K 02AHB9A972 02AHB9A972 029X000116 028R200033 02AHB0A0A4 02167E100K 02167F2R2J 02AHB9A972 031626009R 02167F101J 02167F470J 02167F470J 02167D101K 021LA6101K 02167F220J 02167F220J 02167F220J 02167F101J 021LA6101K 02167F101J 02167F1R0K 02167F1R0K 02167F1R0K 045013003J 0481390424
DESCRIPTION TRANSISTORS
TRANSISTOR,SILICON FET TRANSISTOR, SILICON COMPOUND TRANSISTOR COMPOUND TRANSISTOR COMPOUND TRANSISTOR TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON COMPOUND TRANSISTOR TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON COMPOUND TRANSISTOR TRANSISTOR, SILICON TRANSISTOR,SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON COMPOUND TRANSISTOR KTC3198-AT(Y,GR) STF10NK50Z KTC3203_Y-AT RT1N141C-T112-1 RT1N141C-T112-1 RT1N141C-T112-1 2SA1036KT146 2SA2048TL 2SC3052-T1 KTC3875S_Y_RTK 2SC3052-T1 KTC3875S_Y_RTK 2SC3052-T1 KTC3875S_Y_RTK 2SC3052-T1 KTC3875S_Y_RTK KTC3209_Y-AT KTC3209_Y-AT KTA1281_Y KTC3209_Y-AT 2SC3052-T1 KTC3875S_Y_RTK KTC3209_Y-AT 2SC3052-T1 KTC3875S_Y_RTK 2SC3052-T1 KTC3875S_Y_RTK RT1N241C-T112-1 2SC3052-T1 KTC3875S_Y_RTK 2SC3052-T1 KTC3875S_Y_RTK RT1P241C-T112-1 KTC3203_Y-AT KTA1266-AT(Y,GR) 2SC3052-T1 KTC3875S_Y_RTK 2SC3052-T1 KTC3875S_Y_RTK 2SA1530A-T1 2SA1530A-T1 2SC3052-T1 KTC3875S_Y_RTK 2SC3052-T1 KTC3875S_Y_RTK RT1N241C-T112-1 100 UH ELH5L4113 4.7 MH 100 UH 100 UH W5T29X7.5X19 W5T29X7.5X19 SS28V-R20130 8R200033 W5T_20X10X10A 10 UH 2.2 UH W5T29X7.5X19 1626009 100 UH 47 UH 47 UH 100 UH 100 UH 22 UH 22 UH 22 UH 100 UH 100 UH 100 UH 1 UH 1 UH 1 UH ETH14Y47AY 81390424
or or or or
ICS
IC IC INIT DATA IC IC IC IC PHOTO COUPLER IC IC IC IC IC IC IC MEMORY DATA IC IC IC IC IC IC IC
! !
or
! ! ! ! ! ! !
or or
or or
M12L16161A-7TG HY57V161610ETP-7 LA71205M-MPB AN3663FBP MM1502XNRE MM1502XNRE PCM1753DBQR ST-304L RT1N241C-T112-1 ST-304L RPI-352C40N RPI-352C40N RT1N241C-T112-1 RPI-303 RPI-303 RT1N141C-T112-1 2SC3052-T1 KTC3875S_Y_RTK 2SA1530A-T1 2SC3052-T1 KTC3875S_Y_RTK 2SC3052-T1 KTC3875S_Y_RTK RT1N441C-T112-1 KTC3227_Y-AT 2SD2499(LB0EC1) KRC102MAT KTC3207-AT 2SA1624-AA RT1N141C-T112-1 2SC3052-T1 KTC3875S_Y_RTK RT1P141C-T112-1 2SC3052-T1 KTC3875S_Y_RTK KTC4217(O,Y) 2SC4217(D,E)-RAC KTC3199_Y-AT KTC4217(O,Y) 2SC4217(D,E)-RAC KTC3199_Y-AT KTC4217(O,Y) 2SC4217(D,E)-RAC KTC3199_Y-AT
or or
TRANSISTORS
PHOTO TRANSISTOR COMPOUND TRANSISTOR PHOTO TRANSISTOR PHOTO COUPLER PHOTO COUPLER COMPOUND TRANSISTOR PHOTO COUPLER PHOTO COUPLER COMPOUND TRANSISTOR TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON COMPOUND TRANSISTOR TRANSISTOR SILICON TRANSISTOR SILICON COMPOUND TRANSISTOR TRANSISTOR SILICON TRANSISTOR,SILICON COMPOUND TRANSISTOR TRANSISTOR SILICON TRANSISTOR SILICON COMPOUND TRANSISTOR TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR,SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR,SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR,SILICON TRANSISTOR SILICON
or or
COILS &TRANSFORMERS
COIL COIL,LINEARITY COIL COIL COIL CORE,FERRITE CORE,FERRITE COIL,LINE FILTER COIL,DEGAUSS CORE FERRITE COIL COIL CORE,FERRITE COIL,BIAS OSC COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL TRANS,HORIZONTAL DRIVE TRANSFORMER,SWITCHING
or
or or
or
or or
or
or
J4-2
DESCRIPTION
SOCKET,CATHODE RAY,TUBE HEADPHONE JACK RCA JACK RCA JACK RCA JACK RCA JACK RCA JACK RCA JACK RCA JACK RCA JACK ISHS62S MSJ-2000_AG MTJ-032-05A-30-FE RCA-102S(YL) MTJ-032-05A-32-FE RCA-102S(WH) MTJ-032-05A-31-FE RCA-102S(RD)
MSP-251V-05NI-FE-LF
REF. NO.
CP101 CP303 CP404 CP601 CP602 CP603 CP604 CP803 CP804 CP805 CD1702 CD1705 CD2251 CD4002 CD4501 CD4503 CD8101 CP1702 CP1704 CP1707 CP1708 CP2201 CP2301 CP2302 CP2303 CP4501 CP4502 CP4503 CP602B CP603B CP8001 CP8002 CP802A CP802B CP8101 CUS011 CUS012 EL001 EL002 EL003 EL004 F1701 FB401 FH1701 FH1702 OS2201 RY1701
PART NO.
06972C0010 069S140419 069S450089 069S240639 067U009039 067U008029 069S280629 069S320010 069D010010 069S320010 1209415910 06CH012403 06CH220705 06CU2B3301 122F061502 W9L6012042 122F0C1602 067U008029 069S420110 069D01001A 069D01001A 069S220629 069KYOT159 069EV53030 069EV63030 0697290620 069J760599 067U002019 069S290629 069S280629 069S2B0629 069J7C0599 067U005049 067U005049 069J7C0589 800WFAA007 800WFAA008 124120301A 124116281A 124120301A 124116281A 081PC6R305 043220068Y 06710T0009 06710T0009 077A031003 0560V20119 0560V20115 070W546008 070W546008 076R0HH01B 0163300022 DF5EL3R0A0 098Q210464 100DA32R01 100CT01403 100CT3R532 100BT02701 100CT3R502
DESCRIPTION MISCELLANEOUS
CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE WIRE HOLDER WIRE HOLDER CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CORD AC BUSH CORD EIS CONNECTOR CORD CONNECTOR CORD CONNECTOR CORD JUMPER FLAT CABLE AWM2468 CORD JUMPER WIRE HOLDER CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE WIRE HOLDER CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE WIRE HOLDER WIRE HOLDER CONNECTOR PCB SIDE CUSHION B CUSHION C EYE LET EYE LET EYE LET EYE LET FUSE TRANSFORMER,FLYBACK HOLDER,FUSE HOLDER,FUSE REMOTE RECEIVER RELAY RELAY SPEAKER SPEAKER TRANSMITTER RF UNIT DEGAUSS ELEMENT CRT W/DY CRYSTAL CRYSTAL CRYSTAL CRYSTAL CRYSTAL TMC-J12P-B2 A2502WV2-4P A1561WV2-A5P A2001WR2-4P B2013H02-9P B2013H02-8P A2001WV2-8P A2361WV2-2P 005P-2100 A2361WV2-2P 9415910 CH012403 CH220705 CU2B3301 2F061502
AWG26 2C BLACK 120MM
or or or or
RCA-117-01 ! LSA-1144EAU MXS01350MVP0 EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R NVG6TLTAB222 NVG6TLTAB103 DME069A CME029B CCE024B DME060A CEE055B W5RH3.5X5X1.0 W5RH3.5X5X1.0 W5RH3.5X5X1.0 W4BRH3.5X6X1.0 W4BRH3.5X6X1.0 MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT W4BRH3.5X6X1.0X2 MMZ1608R102CT CU011902 CH149006 CU291701 CU284501 CU282401
AWG26 5C GRAY 440MM
SWITCHES
SW101 SW2201 SW2202 SW2203 SW2204 SW2205 SW2206 SW2207 SW2251 SW2252 SW2253 SW2254 SW2255 SW2256 SW2257 SW2258 VR404 VR1701 PCB010 PCB080 PCB110 PCB130 PCB270 B401 B402 B403 B1703 B2201 B2301 B2302 B2303 B2304 B2305 B4001 B4002 B4003 B4005 B4006 B4007 B4008 B4009 B4010 B4011 B4012 B4013 B4014 B4016 B4018 B8001 B8103 CD002 CD303 CD602 CD603 CD604 CD802 CD803 CD805 CD807 CD808 CP001 SWITCH (LEAF) SWITCH(LEAF) SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT or
VARIABLE RESISTORS
VOLUME,SEMI FIXED VOLUME,SEMI FIXED
P.C.BOARD ASSEMBLIES
PCB ASS'Y PCB ASS'Y PCB ASS'Y PCB ASS'Y PCB ASS'Y
TOC-C09X-A1 IMSA-9604S-06C B2013H02-2P A2001WV2-9P A2001WV2-8P A2001WV2-11P IMSA-9604S-12C B2013H02-5P B2013H02-5P IMSA-9604S-12F
MISCELLANEOUS
CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORD CONNECTOR CORD CONNECTOR CORD CONNECTOR CORD CONNECTOR CORD CONNECTOR FLAT CABLE AWM2468 CORD CONNECTOR CORD CONNECTOR CORD EIS CONNECTOR CORD EIS CONNECTOR CONNECTOR PCB SIDE
! !
! SP351 ! SP352 TM101 ! TU001 ! TH1701 ! V801 X101 X102 X601 X4001 X4501
XRY20X30BD XRY16X28BD XRY20X30BD XRY16X28BD 51MS063L BSC27-N2265 EYF-52BCY EYF-52BCY ROM-V3138SR ALKS321_M60 ALKS321 MSF-18D5SB05 MSF-18D5SB05 R56-0487 115-V-KA35ARH ZPB45BL3R0A A51AKL13X04(M) DT-26 HC-49/U-S HC-49/U-S HC-49U/S HC-49/U
or
RESISTOR RC...................
CARBON RESISTOR
CAPACITORS CC................... CERAMIC CAPACITOR CE................... ALUMI ELECTROLYTIC CAPACITOR CP................... POLYESTER CAPACITOR CPP.................. POLYPROPYLENE CAPACITOR CPL.................. PLASTIC CAPACITOR CMP..................... METAL POLYESTER CAPACITOR CMPL................ METAL PLASTIC CAPACITOR CMPP................ METAL POLYPROPYLENE CAPACITOR
J4-3
M5V4-04J W625039