Académique Documents
Professionnel Documents
Culture Documents
com
WELDING OSCILLATOR
MODELED-WRS
DIRECOTRY
1. Features ......................................................................................... 2 2. Technical parameters ..................................................................... 2 3. Control panel ................................................................................. 2 4. Operation....................................................................................... 3 5. Oscillate mode and track ............................................................... 3 6. Installation ..................................................................................... 4 7. Troubles and Countermeasures...................................................... 5 8. Control Box Parts List ................................................................... 6 9. Slide Parts List............................................................................... 8 10. Electrical schematic................................................................... 10
3. Control panel 1Power switch: Power indicator will light when power switch is at ON position, and it must turn OFF after complete the work. 2Power indicator: Power switch to the ON position, the power indicator lights. 3Power Fuse: If the current overload, the fuse will be fused to protect the system. 4Start button: Press this button to work immediately. 5Stop button: Press this button to stop working. 6Left stop time: Control the torch staying time at left, time setting range 0 ~ 2s. 7Left stop time: Control the torch staying time at left, time setting range 0 ~ 2s. 8Speed control: Can control the swing frequency. 9Swing control: Can control the swing amplitude. 10Center adjust: Can control the center of swing
4. Operation ED-WRS oscillator is very convenient device, the control device directly to the swing line access control box, the swing mounted on the running device, adjusting the button on the control box. 1Power switch in the ON position - the power indicator light 2Move the center adjustment knob 3Adjust stop time (two points individually adjustable), four swing modes 4Adjust width knob 5Adjust speed knob 6Began to swing at a set value, look at the actual torch swing, adjust the knob according to welding requirements 7Welding is completed: swing runs switch OFF position (when torch automatically return to the center), the power switch to OFF position 5. Oscillate mode and track Left and right stop time are both zero
Left and right stop time are both longer than zero
Left stop time is longer than zero Right stop time is zero
Left stop time is zero Right stop time is longer than zero
2Vertical Horizontal arc welding torch swing, the distance between the workpiece and the distance will become long on both sides
Check items
Check power Check fuse Check switch Check cable Check light Check switch Check speed knob Check PCB board Check motor Check knob Check PCB board running at lowest speed running at fastest speed Check power Check motor Check PCB board Over loaded
Solutions
Supply new power Replace fuse Replace switch Replace cable Replace light Replace switch Replace knob Inform manufacturers Replace motor Replace switch inform manufacturers Check and replace PCB board Supply new power Replace motor Inform manufacturers Reduce loading
No stop time
Parts List
NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Description box Side handle Top handle magnet Magnet base Rubber feet Drive PCB Panel plate Holder with fuse receptacle Power receptacle Panel PCB Potentiometer Button cover Turning knob Stop button switch Start button switch Power switch Power lamp Mat' / Model steel Stainless steel alum 40*20*10 alum rubber alum 250v, 5A 6P 3P 5k brass plastic 103C 103C Quantity Remarks 1 2 1 1 1 4 2 1 1 1 1 1 5 2 5 1 Red cap 1 Black cap 1 1
Parts List
NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 Description base drive motor top plate bearing worm bearing Potentiometer base potentiometer Side plate Worm gear Clamp bush clamp Holder base plate Holder bottom plate Holder cover plate Connection pole Connection bush Connection base motor cover Receptacle base receptacle Mat' / Model alum DC24V, 1/100 alum #6901zz rs25 #6900zz alum 5k alum steel bakelite alum steel alum alum alum bakelite alum steel alum 6P Quantity 1 1 1 3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Remarks
10