Académique Documents
Professionnel Documents
Culture Documents
Material Datasheet
Material Notes: Data provided by Quadrant Engineering Plastic Products Physical Properties Specific Gravity Water Absorption Metric 1.15 g/cc 0.6 % English 0.0415 lb/in 0.6 % Comments ASTM D792 Immersion, 24hr; ASTM D570(2) Immersion; ASTM D570(2)
7%
7%
Mechanical Properties Hardness, Rockwell M Hardness, Rockwell R Hardness, Shore D Tensile Strength, Ultimate Elongation at Break Tensile Modulus Flexural Modulus Flexural Yield Strength C ompressive Strength C ompressive Modulus Shear Strength C oefficient of Friction 85 115 85 82.7 MPa 20 % 2.76 GPa 3.45 GPa 110 MPa 103 MPa 2.76 GPa 75.8 MPa 0.2 85 115 85 12000 psi 20 % 400 ksi 500 ksi 16000 psi 15000 psi 400 ksi 11000 psi 0.2 ASTM D785 ASTM D785 ASTM D2240 ASTM D638 ASTM D638 ASTM D638 ASTM D790 ASTM D790 10% Def.; ASTM D695 ASTM D695 ASTM D732 Dry vs. Steel; QTM55007 QTM 55010 4:1 safety factor; QTM 55007 ASTM D256 Type A
201 x 10- 8 mm/N-M 100 x 10- 1 0 in-min/ft-lb-hr 0.105 MPa-m/sec 3000 psi-ft/min
0.214 J/cm
0.4 ft-lb/in
Electrical Properties Surface Resistivity per Square Dielectric C onstant Dielectric Strength Min 1e+013 ohm 3.7 19.7 kV/mm Min 1e+013 ohm 3.7 500 V/mil EOS/ESD S11.11 1MHz; ASTM D150 Short Term; ASTM D149
Thermal Properties C TE, linear 68F 90 m/m-C 50 in/in-F (-40F to 300F); ASTM E831 ASTM F433 C rystalline, Peak; ASTM D3418 Long Term ASTM D648
1/2
Maximum Service Temperature, Air Deflection Temperature at 1.8 MPa (264 psi)
quadrant.matweb.com/SpecificMaterialPrint.asp?bassnum=p1sm21c
127 C 93.3 C
260 F 200 F
1/20/13
Material Datasheet
Flammability, UL94 (Estimated Rating) Qualitative Processing Properties C ompliance - FDA Machinability Service in Alcohols Service in Aliphatic Hydrocarbons Service in Aromatic Hydrocarbons Service in C hlorinated Solvents Service in Ethers Service in Ketones Service in Strong Acids Service in Strong Alkalies Service in Sunlight Service in Weak Acids Service in Weak Alkalies
HB
HB
1/8 inch
Not C ompliant 1 Limited Acceptable Acceptable Limited Acceptable Acceptable Unacceptable Unacceptable Limited Limited Limited 1-10, 1=Easier to Machine
A ll s tatements , tec hnic al information and rec ommendations c ontained in this databas e are pres ented in good faith, bas ed upon tes ts believed to be reliable and prac tic al field experienc e. T he reader is c autioned, however, that Q uadrant E P P and A utomation C reations , I nc . c annot guarantee the ac c urac y or c ompletenes s of this information, and it is the c us tomer's res pons ibility to determine the s uitability of Q uadrant E P P 's produc ts in any given applic ation.
quadrant.matweb.com/SpecificMaterialPrint.asp?bassnum=p1sm21c
2/2