Vous êtes sur la page 1sur 64

C

Relion 615 Series

Transformer Protection and Control

Document ID: 1MAC270644-MB Issued: 04/14/2011 Revision: B Product version: 4.0

Copyright 2011 ABB. All rights reserved.

1MAC207644-MB B

Section

Section 1

Introduction ...........................................................................3
This manual .............................................................................................. 3 Intended audience .................................................................................... 3 Product documentation............................................................................. 4 Product documentation set.................................................................. 4 Document revision history ................................................................... 5 Related documentation........................................................................ 5 Symbols and conventions......................................................................... 5 Safety indication symbols .................................................................... 5 Manual conventions............................................................................. 6 Functions, codes and symbols ............................................................ 7

Section 2

Modbus data mappings.......................................................11


Overview................................................................................................. 11 Point list for RET615 v4.0 ANSI.............................................................. 12

Section 3

Glossary..............................................................................55

RET615 ANSI Point List Manual

Section

1MAC207644-MB B

RET615 ANSI Point List Manual

1MAC207644-MB B

Section 1 Introduction

Section 1

Introduction

1.1

This manual
The point list manual describes the outlook and properties of the data points specific to the IED. The manual should be used in conjunction with the corresponding communication protocol manual.

1.2

Intended audience
This manual addresses the communication system engineer or system integrator responsible for pre-engineering and engineering for communication setup in a substation from an IED perspective. The system engineer or system integrator must have a basic knowledge of communication in protection and control systems and thorough knowledge of the specific communication protocol.

RET615 ANSI Point List Manual

Section 1 Introduction

1MAC207644-MB B

1.3
1.3.1

Product documentation
Product documentation set
Decommissioning Deinstalling & Disposal
RET615 ANSI Point List Manual

Planning & purchase

Commissioning

Engineering

Application manual Engineering manual Installation manual Operation manual Technical manual Communication Protocol manual Protocol Points List manual

Figure 1:

The intended use of manuals in different lifecycles

The engineering manual contains instructions on how to engineer the IEDs using the different tools in PCM600. The manual provides instructions on how to set up a PCM600 project and insert IEDs to the project structure. The manual also recommends a sequence for engineering of protection and control functions, LHMI functions as well as communication engineering for IEC 61850 and DNP3. The installation manual contains instructions on how to install the IED. The manual provides procedures for mechanical and electrical installation. The chapters are organized in chronological order in which the IED should be installed. The operation manual contains instructions on how to operate the IED once it has been commissioned. The manual provides instructions for monitoring, controlling and setting the IED. The manual also describes how to identify disturbances and how to view calculated and measured power grid data to determine the cause of a fault. The application manual contains application descriptions and setting guidelines sorted per function. The manual can be used to find out when and for what purpose a typical protection function can be used. The manual can also be used when calculating settings. The technical manual contains application and functionality descriptions and lists function blocks, logic diagrams, input and output signals, setting parameters and technical data
4

Maintenance

Installing

Operation

1MAC207644-MB B

Section 1 Introduction

Although warning hazards are related to personal injury, it should be understood that operation of damaged equipment could, under certain operational conditions, result in degraded process performance leading to personal injury or death. Therefore, comply fully with all warning and caution notices.

RET615 ANSI Point List Manual

Section 1 Introduction 1.4.2 Manual conventions

1MAC207644-MB B

Conventions used in IED manuals. A particular convention may not be used in this manual. Abbreviations and acronyms in this manual are spelled out in the glossary. The glossary also contains definitions of important terms. Push button navigation in the LHMI menu structure is presented by using the push button icons, for example: To navigate between the options, use and . HMI menu paths are presented in bold, for example: Select Main menu > Settings. LHMI messages are shown in Courier font, for example: To save the changes in non-volatile memory, select Yes and press Parameter names are shown in italics, for example: The function can be enabled and disabled with the Operation setting. Parameter values are indicated with quotation marks, for example: The corresponding parameter values are "Enabled" and "Disabled". IED input/output messages and monitored data names are shown in Courier font, for example: When the function picks up, the PICKUP output is set to TRUE. Dimensions are provided both in inches and mm. If it is not specifically mentioned then the dimension is in mm. .

RET615 ANSI Point List Manual

1MAC207644-MB B

Section 1 Introduction Functions, codes and symbols


Table 1:
Function Protection Three-phase non-directional overcurrent protection, low stage, instance 1 Three-phase non-directional overcurrent protection, low stage, instance 2 Three-phase non-directional overcurrent protection, high stage, instance 1 Three-phase non-directional overcurrent protection, high stage, instance 2 Three-phase non-directional overcurrent protection, high stage, instance 3 Three-phase non-directional overcurrent protection, high stage, instance 4 Three-phase directional overcurrent protection, low stage, instance 1 Three-phase directional overcurrent protection, low stage, instance 2 Non-directional ground-fault protection, low stage, instance 1 Non-directional ground-fault protection, low stage, instance 2 Non-directional ground-fault protection, low stage, instance 3 Non-directional ground-fault protection, high stage, instance 1 Non-directional ground-fault protection, high stage, instance 2 Non-directional ground-fault protection, high stage, instance 3 Non-directional ground-fault protection, high stage, instance 4 Non-directional ground-fault protection, high stage, instance 5 Non-directional ground-fault protection, high stage, instance 6 Directional ground-fault protection, low stage, instance 1 Directional ground-fault protection, low stage, instance 2 Negative-sequence overcurrent protection, instance 1 Negative-sequence overcurrent protection, instance 2 Residual overvoltage protection, instance 1 Residual overvoltage protection, instance 2 Residual overvoltage protection, instance 3 PHLPTOC1 PHLPTOC2 PHHPTOC1 PHHPTOC2 PHHPTOC3 PHHPTOC4 DPHLPDOC1 DPHLPDOC2 EFLPTOC1 EFLPTOC2 EFLPTOC3 EFHPTOC1 EFHPTOC2 EFHPTOC3 EFHPTOC4 EFHPTOC5 EFHPTOC6 DEFLPDEF1 DEFLPDEF2 NSPTOC1 NSPTOC2 ROVPTOV1 ROVPTOV2 ROVPTOV3 51P (1) 51P (2) 50P-1 (1) 50P-1 (2) 50P-2 (1) 50P-2 (2) 67/51P (2) 67/51P (1) 51N (1) 51N (2) 51G 50G-1 50G-2 50N-1 (1) 50N-1 (2) 50N-2 (1) 50N-2 (2) 67/51N (2) 67/51N (1) 46 (1) 46 (2) 59G (2) 59N (2) 59N (1) 3I> (1) 3I> (2) 3I>> (1) 3I>> (2) 3I>> (3) 3I>> (4) 3I> -> (1) 3I> -> (2) Io> (1) Io> (2) Io> (3) Io>> (1) Io>> (2) Io>> (3) Io>> (4) Io>> (5) Io>> (6) Io> -> (1) Io> -> (2) I2> (1) I2> (2) Uo> (1) Uo> (2) Uo> (3)

1.4.3

unctions included in the RET615 standard configurations


IEC61850 ANSI/C37.2 2008 IEC60617

RET615 ANSI Point List Manual

Section 1 Introduction

1MAC207644-MB B

Function Residual overvoltage protection, instance 4 Three-phase undervoltage protection, instance 1 Three-phase undervoltage protection, instance 2 Three-phase overvoltage protection, instance 1 Three-phase overvoltage protection, instance 2 Negative-sequence overvoltage protection, instance 1 Negative-sequence overvoltage protection, instance 2 Frequency protection, instance 1 Frequency protection, instance 2 Frequency protection, instance 3 Frequency protection, instance 4 Voltage per hertz protection, instance 1 Voltage per hertz protection, instance 2 Voltage per hertz protection, instance 3 Voltage per hertz protection, instance 4 Three-phase thermal overload protection for power transformers, two time constants Stabilized and instantaneous differential protection for 2W transformers Numerical stabilized low impedance restricted ground-fault protection Circuit breaker failure protection, instance 1 Circuit breaker failure protection, instance 2 Master trip, instance 1 Master trip, instance 2 Arc protection, instance 1 Arc protection, instance 2 Arc protection, instance 3 Load shedding and restoration, instance 1 Load shedding and restoration, instance 2 Load shedding and restoration, instance 3 Load shedding and restoration, instance 4 Loss of phase, instance 1 Control Circuit-breaker control, instance 1

IEC61850 ROVPTOV4 PHPTUV1 PHPTUV2 PHPTOV1 PHPTOV2 NSPTOV1 NSPTOV2 FRPFRQ1 FRPFRQ2 FRPFRQ3 FRPFRQ4 OEPVPH1 OEPVPH2 OEPVPH3 OEPVPH4 T2PTTR1 TR2PTDF1 LREFPNDF1 CCBRBRF1 CCBRBRF2 TRPPTRC1 TRPPTRC2 ARCSARC1 ARCSARC2 ARCSARC3 LSHDPFRQ1 LSHDPFRQ2 LSHDPFRQ3 LSHDPFRQ4 PHPTUC1

ANSI/C37.2 2008 59G (1) 27 (2) 27 (1) 59 (2) 59 (1) 47 (2) 47 (1) 81-1 (2) 81-2 (2) 81-1 (1) 81-2 (1) 24-1 (2) 24-2 (2) 24-1 (1) 24-2 (1) 49T (1) 87T 87LOZREF (2) 50BF (2) 50BF (1) 86/94-1 86/94-2 AFD-1 (2) AFD-2 (2) AFD-3 (2) 81LSH-1 (2) 81LSH-2 (2) 81LSH-1 (1) 81LSH-2 (1) 37 (1)

IEC60617 Uo> (4) 3U< (1) 3U< (2) 3U> (1) 3U> (2) U2> (1) U2> (2) f>/f<,df/dt (1) f>/f<,df/dt (2) f>/f<,df/dt (3) f>/f<,df/dt (4) U/f> (1) U/f> (2) U/f> (3) U/f> (4) 3Ith>T 3dI>T dIoLo> 3I>/Io>BF (1) 3I>/Io>BF (2) Master Trip (1) Master Trip (2) ARC (1) ARC (2) ARC (3) UFLS/R (1) UFLS/R (2) UFLS/R (3) UFLS/R (4) 3I< (1)

CBXCBR1

52 (2)

I <-> O CB (1)

RET615 ANSI Point List Manual

1MAC207644-MB B

Section 1 Introduction

Function Circuit-breaker control, instance 2 Tap changer position indication Condition Monitoring Circuit-breaker condition monitoring, instance 1 Circuit-breaker condition monitoring, instance 2 Trip circuit supervision, instance 1 Trip circuit supervision, instance 2 Advanced current circuit supervision for transformers Fuse failure supervision, instance 1 Fuse failure supervision, instance 2 Measurement Three-phase current measurement, instance 1 Three-phase current measurement, instance 2 Sequence current measurement, instance 1 Sequence current measurement, instance 2 Residual current measurement, instance 1 Three-phase voltage measurement, instance 1 Three-phase voltage measurement, instance 2 Residual voltage measurement Sequence voltage measurement, instance 1 Sequence voltage measurement, instance 2 Single-phase power and energy measurement, instance 1 Single-phase power and energy measurement, instance 2 Three-phase power and energy measurement, instance 1 Three-phase power and energy measurement, instance 2 Frequency measurement Recorder Disturbance recorder Fault recorder Sequence event recorder Other Functions Minimum pulse timer (2 pcs), instance 1

IEC61850 CBXCBR2 TPOSSLTC1

ANSI/C37.2 2008 52 (1) 84T

IEC60617 I <-> O CB (2) TPOSM

SSCBR1 SSCBR2 TCSSCBR1 TCSSCBR2 CTSRCTF1 SEQRFUF1 SEQRFUF2

52CM (2) 52CM (1) TCM-1 TCM-2 MCS 3I, I2 60 (2) 60 (1)

CBCM (1) CBCM (2) TCS (1) TCS (2) MCS 3I, I2 FUSEF (1) FUSEF (2)

CMMXU1 CMMXU2 CSMSQI1 CSMSQI2 RESCMMXU1 VMMXU1 VMMXU2 RESVMMXU1 VSMSQI1 VSMSQI2 SPEMMXU1 SPEMMXU2 PEMMXU1 PEMMXU2 FMMXU1

IA, IB, IC (2) IA, IB, IC (1) I1, I2, I0 (2) I1, I2, I0 (1) IG VA, VB, VC (2) VA, VB, VC (1) VG V1, V2, V0 (2) V1, V2, V0 (1) SP, SE (2) SP, SE (1) P, E (2) P, E (1) f

3I 3I(B) I1, I2, I0 I1, I2, I0(B) Io 3U 3U(B) Uo U1, U2, U0 U1, U2, U0(B) SP, SE SP, SE(B) P, E P, E(B) f

RDRE1 FLMSTA1 SER

DFR FR SER

TPGAPC1

TP - 1

TP (1)

RET615 ANSI Point List Manual

Section 1 Introduction

1MAC207644-MB B

Function Minimum pulse timer (2 pcs), instance 2 Minimum pulse timer (2 pcs), instance 3 Minimum pulse timer (2 pcs), instance 4 Pulse timer (8 pcs), instance 1 Pulse timer (8 pcs), instance 2 Time delay off (8 pcs), instance 1 Time delay off (8 pcs), instance 2 Time delay on (8 pcs), instance 1 Time delay on (8 pcs), instance 2 Set reset (8 pcs), instance 1 Set reset (8 pcs), instance 2 Move (8 pcs), instance 1 Move (8 pcs), instance 2

IEC61850 TPGAPC2 TPGAPC3 TPGAPC4 PTGAPC1 PTGAPC2 TOFGAPC1 TOFGAPC2 TONGAPC1 TONGAPC2 SRGAPC1 SRGAPC2 MVGAPC1 MVGAPC2

ANSI/C37.2 2008 TP - 2 TP - 3 TP - 4 PT-1 PT-2 TOF-1 TOF-2 TON -1 TON -2 SR-1 SR-2 MV-1 MV-2

IEC60617 TP (2) TP (3) TP (4) PT (1) PT (2) TOF (1) TOF (2) TON (1) TON (2) SR (1) SR (2) MV (1) MV (2)

10

RET615 ANSI Point List Manual

1MAC207644-MB B

Section 2 Modbus data mappings

Section 2

Modbus data mappings

2.1

Overview
This document describes the Modbus data points and structures available in RET615 Ver. 4.0.

Point list table columns


0x addr AFL-Common SA name Bit addr Ctrl bit Ctrl struct Dc DS FD Num Identification Item Mode Object Offset Reg addr Reg.bit addr Scale Signal name Type UID W Coil (0X) PLC address, base address = 1 AFL name of the corresponding data signal Bit (1X and 0X) PLC address, base address = 1 Control bit (0..15) within control structure Control structure number Data category Object resides as default in some IEC 61850 data set (Y = yes, N = no) Unique number of the platform SW component IED's internal IEC 61850 signal name Unique number of an data item within the data object Control object mode: unsecured or secured Unique number of a data object within the SW component Offset factor, default setting Modbus register address (3X or 4X). PLC address, base address = 1 Register PLC address (3X and 4X) and bit within register (0..15) Scale factor, default setting IEC 61850 signal description Register type and value interpretation: signed or unsigned Unique ID combination of FD Num, Object and Item Writable register

RET615 ANSI Point List Manual

11

Section 2 Modbus data mappings

1MAC207644-MB B

2.2

Point list for RET615 v4.0 ANSI


Table 2: System Status Registers
Scale OffSet Description System Status Register, 1 System Status Register, 2 System Status Register, 3 System Status Register, 4 System Status Register, 5 System Status Register, 6 Device Information IEC61850 Data Attribute Name

Coil Addr

Register(:Bit) Addr 129 130 131 132 133 134 135 .. 225 245

Dc 0 0 0 0 0 0 0 0 0

Type u16 u16 u16 u16 u16 u16 u16 u16 u16 u16

Parameter Setting Group in Use

Table 3:
Coil Addr Register(:Bit) Addr 226 227 228 229 230 231 Dc 0 0 0 0 0 0 Type u16 u16 u16 u16 u16 u16

Time Stamp of Last Device Reset


Scale OffSet Description Year(High Byte)/Month(Low Byte) Day(High Byte)/Hour(Low Byte) Min(High Byte)/Sec(Low Byte) MilliSecond Time Quality Cause of Reset ( 1-Power Reset, 2-Watchdog Reset, 3-Warm Reset) IEC61850 Data Attribute Name

Table 4:
Coil Addr Register(:Bit) Addr 497 498 499 500 501 502 503 504 W x x x x x x x x Type u16 u16 u16 u16 u16 u16 u16 u16

Device Real-Time clock in local Time


Scale OffSet Description Real-time struct - Control register(0..2) Real-time struct - Year (2000-2999) Real-time struct - Month (1..12) Real-time struct - Day (1..31) Real-time struct - Hour (0..23) Real-time struct - Minute (0..59) Real-time struct - Seconds (0..59) Real-time struct - Milliseconds (0..999) IEC61850 Data Attribute Name

12

RET615 ANSI Point List Manual

1MAC207644-MB B

Section 2 Modbus data mappings

Table 5:
Coil Addr Register(:Bit) Addr 516 517 518 519 520 521 522 523 W x x x x x x x x Type u16 u16 u16 u16 u16 u16 u16 u16

Device Real-Time clock in UTC Time


Scale OffSet Description Real-time struct - Control register(0..2) Real-time struct - Year (2000-2999) Real-time struct - Month (1..12) Real-time struct - Day (1..31) Real-time struct - Hour (0..23) Real-time struct - Minute (0..59) Real-time struct - Seconds (0..59) Real-time struct - Milliseconds (0..999) IEC61850 Data Attribute Name

Table 6:
Coil Addr Register(:Bit) Addr 1561 1562 1563 1564 1565 1566 1567 1568 1569 1570 1571 1572 1573 W x x Type u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16

Event Records
Scale OffSet Description Number of Events to Read 1 1 1 1 1 1 1 1 1 1 1 1 Event Selection Sequence Number Number of Unread Records Year(High Byte)/Month(Low Byte) Day(High Byte)/Hour(Low Byte) Min(High Byte)/Sec(Low Byte) MilliSecond Event Type Data Object ID 1 1) Data Object ID 2 1) Event Data Value Event Data Value IEC61850 Data Attribute Name

1) See Decoding of Data Object ID1 and 1

Decoding of Data Object ID1 and Data Object ID2


The base 4x Modbus address is Data Object ID2/16. Bit offset is the remainder of DataObject ID2/16. For Instance, Bit 10 in register of 2500 would appear in Data Object ID2 as 0x9C4A = 40010. The base address is 40010/16 = 2500. The bit is 0.625 x 16 = 10. Data Object ID1 is the most significant 16 bits. If Data Object ID1 is non-zero then a 32 bit number is composed of Data Object ID1 as bits 31-16 and Data Object ID2 are bits 15-0.

RET615 ANSI Point List Manual

13

Section 2 Modbus data mappings

1MAC207644-MB B

Table 7:
Coil Addr Register(:Bit) Addr 1712 1713 1714 1715 1716 1717 1718 1719 1720 1721 1722 1723 1724 1725 1726 1727 1728 1729 1730 1731 1732 1733 1734 1735 1736 1737 1738 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 W x Dc

Fault records
Type u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 Scale 1 1 1 1 1 1 1 1 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 Description Fault Record Selection Sequence Number Number of Unread Records Year(High Byte)/Month(Low Byte) Day(High Byte)/Hour(Low Byte) Min(High Byte)/Sec(Low Byte) MilliSecond Time Quality Last Fault: Max Phase A Current Magnitude Last Fault: Max Phase B Current Magnitude Last Fault: Max Phase C Current Magnitude Last Fault: Max Neutral Current Magnitude Last Fault: Phase A Current Magnitude Last Fault: Phase B Current Magnitude Last Fault: Phase C Current Magnitude Last Fault: Neutral Current Magnitude Last Fault: Calculated Residual Current Magnitude Last Fault: Negative Sequence Current Mag. Last Fault: Positive Sequence Current Mag. Last Fault: Phase A Voltage Magnitude Last Fault: Phase B Voltage Magnitude Last Fault: Phase C Voltage Magnitude Last Fault: Measured Residual Voltage Magnitude Last Fault: Negative Sequence Voltage Magnitude Last Fault: Positive Sequence Voltage Magnitude Last Fault: Zero Sequence Voltage Magnitude Last Fault: Phase AB Voltage Magnitude LD0.FLTMSTA1.MaxAmpsA.mag .f LD0.FLTMSTA1.MaxAmpsB.mag .f LD0.FLTMSTA1.MaxAmpsC.mag .f LD0.FLTMSTA1.MaxAmpsN.mag .f LD0.FLTMSTA1.AmpsA.mag.f LD0.FLTMSTA1.AmpsB.mag.f LD0.FLTMSTA1.AmpsC.mag.f LD0.FLTMSTA1.AmpsN.mag.f LD0.FLTMSTA1.AmpsNClc.mag.f LD0.FLTMSTA1.AmpsNgSeq.ma g.f LD0.FLTMSTA1.AmpsPsSeq.ma g.f LD0.FLTMSTA1.VoltsA.mag.f LD0.FLTMSTA1.VoltsB.mag.f LD0.FLTMSTA1.VoltsC.mag.f LD0.FLTMSTA1.VoltsN.mag.f LD0.FLTMSTA1.VNgSeq.mag.f LD0.FLTMSTA1.VPsSeq.mag.f LD0.FLTMSTA1.VZroSeq.mag.f LD0.FLTMSTA1.VoltsAB.mag.f IEC61850 Data Attribute Name

14

RET615 ANSI Point List Manual

1MAC207644-MB B

Section 2 Modbus data mappings

Coil Addr

Register(:Bit) Addr 1739 1740 1741 1742 1743 1744 1745 1746 1747 1748 1749 1750 1751 1752 1753 1754 1755 1756 1757 1758 1759 1760 1761 1762 1763 1764 1765 1766 1767 1768 1769 1770

Dc 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100

Type u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16 u16

Scale 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100

Description Last Fault: Phase BC Voltage Magnitude Last Fault: Phase CA Voltage Magnitude Maximum phase A current (b) Maximum phase B current (b) Maximum phase C current (b) Maximum residual current (b) Phase A current (b) Phase B current (b) Phase C current (b) Residual current (b) Calculated residual current (b) Negative sequence current (b) Positive sequence current (b) Phase A voltage (b) Phase B voltage (b) Phase C voltage (b) Residual voltage (b) Negative sequence voltage (b) Positive sequence voltage (b) Zero sequence voltage (b) Phase A to phase B voltage (b) Phase B to phase C voltage (b) Phase C to phase A voltage (b) Maximum differential current phase A Maximum differential current phase B Maximum differential current phase C Differential current phase A Differential current phase B Differential current phase C Differential current residual Maximum bias current phase A Maximum bias current phase B

IEC61850 Data Attribute Name LD0.FLTMSTA1.VoltsBC.mag.f LD0.FLTMSTA1.VoltsCA.mag.f LD0.FLTMSTA1.MaxAmpsAb.ma g.f LD0.FLTMSTA1.MaxAmpsBb.ma g.f LD0.FLTMSTA1.MaxAmpsCb.ma g.f LD0.FLTMSTA1.MaxAmpsNb.ma g.f LD0.FLTMSTA1.AmpsAb.mag.f LD0.FLTMSTA1.AmpsBb.mag.f LD0.FLTMSTA1.AmpsCb.mag.f LD0.FLTMSTA1.AmpsNb.mag.f LD0.FLTMSTA1.AmpsNClcb.mag .f LD0.FLTMSTA1.AmpsNgSeqb.m ag.f LD0.FLTMSTA1.AmpsPsSeqb.m ag.f LD0.FLTMSTA1.VoltsAb.mag.f LD0.FLTMSTA1.VoltsBb.mag.f LD0.FLTMSTA1.VoltsCb.mag.f LD0.FLTMSTA1.VoltsNb.mag.f LD0.FLTMSTA1.VNgSeqb.mag.f LD0.FLTMSTA1.VPsSeqb.mag.f LD0.FLTMSTA1.VZroSeqb.mag.f LD0.FLTMSTA1.VoltsABb.mag.f LD0.FLTMSTA1.VoltsBCb.mag.f LD0.FLTMSTA1.VoltsCAb.mag.f LD0.FLTMSTA1.MxDifAClcA.mag .f LD0.FLTMSTA1.MxDifAClcB.mag .f LD0.FLTMSTA1.MxDifAClcC.ma g.f LD0.FLTMSTA1.DifAmpsA.mag.f LD0.FLTMSTA1.DifAmpsB.mag.f LD0.FLTMSTA1.DifAmpsC.mag.f LD0.FLTMSTA1.DifAmpsN.mag.f LD0.FLTMSTA1.MxRstAClcA.ma g.f LD0.FLTMSTA1.MxRstAClcB.ma g.f

RET615 ANSI Point List Manual

15

Section 2 Modbus data mappings

1MAC207644-MB B

Coil Addr

Register(:Bit) Addr 1771 1772 1773 1774 1775 1776 1777 1778 1779 1780

Dc 100 100 100 100 100 100 100 100 100 100

Type u16 u16 u16 u16 u16 u16 u16 u16 u16 u16

Scale 100 100 100 100 100 100 100 100 100 100

Description Maximum bias current phase C Bias current phase A Bias current phase B Bias current phase C Bias current residual Last Fault: I2/I1 Ratio Fault Last Fault: Max Temperature Last Fault: Fault Record Operation Counter Last Fault: Frequency At The Time The Fault Is Cleared Last Fault: Frequency Gradient At The Time The Fault Is Cleared Last Fault: Conductance Yo Last Fault: Susceptance Yo Last Fault: Max Pickup (Start) Duration Of All Stages During The Fault Distance to fault measured in pu

IEC61850 Data Attribute Name LD0.FLTMSTA1.MxRstAClcC.ma g.f LD0.FLTMSTA1.RstAmpsA.mag.f LD0.FLTMSTA1.RstAmpsB.mag.f LD0.FLTMSTA1.RstAmpsC.mag.f LD0.FLTMSTA1.RstAmpsN.mag.f LD0.FLTMSTA1.PDNS1MxRat.m ag.f LD0.FLTMSTA1.MaxTmpRl.mag. f LD0.FLTMSTA1.OpCnt.stVal LD0.FLTMSTA1.Hz.mag.f LD0.FLTMSTA1.HzS.mag.f

1781 1782 1783

100 100 100

u16 u16 u16

100 100 100

LD0.FLTMSTA1.CondN.mag.f LD0.FLTMSTA1.SusN.mag.f LD0.FLTMSTA1.StrDur.mag.f

1784

100

u16

100

LD0.FLTMSTA1.FltDisKm.mag.f

Table 8:
Coil Addr 5576 5577 Register(:Bit) Addr 235:0 235:1 244:0 244:1 245:0 245:1 236 Dc 0 0 0 0 0 0 0 Yes Yes Yes MCD

General Device Information (LLN0)


Type Scale Offset Description Local / Remote (1- Local; 0-Remote) Protection LLN0 Settings Reservation Protection LLN0 Settings Change u16 1 0 Local / Remote state IEC61850 Data Attribute Name CTRL.LLN0.Loc.stVal LD0.LLN0.SetSeld.stVal LD0.LLN0.SetChg.stVal CTRL.LLN0.LocRem.stVal

Table 9:
Coil Addr Register(:Bit) Addr 232 233 234 237 238 239 Dc 0 0 0 0 0 0 MCD

Device Physical Information (LPHD1)


Type u16 u16 u16 s16 u16 u16 Scale 1 1 1 1 1 1 Offset 0 0 0 0 0 0 Description Number Of Power Ups Number Of Warm Starts Number Of Watchdog Device Resets General Device State Physical Sevice Warning Internal Fault IEC61850 Data Attribute Name LD0.LPHD1.NumPwrUp.stVal LD0.LPHD1.WrmStr.stVal LD0.LPHD1.WacTrg.stVal LD0.LPHD1.PhyHealth.stVal LD0.LPHD1.PhyHealth1.stVal LD0.LPHD1.PhyHealth2.stVal

16

RET615 ANSI Point List Manual

1MAC207644-MB B

Section 2 Modbus data mappings

Table 10:
Coil Addr 2894 2895 3824 3825 3826 3827 3828 3829 Register(:Bit) Addr 2199:2 2199:3 2245:8 2245:9 2245:10 2245:11 2245:12 2245:13 Dc 0 0 0 0 0 0 0 0 Yes Yes Yes Yes MCD

LED Condition monitoring (LEDPTRC1)


Type Scale Offset Description Global Conditioning Trip (Operate) Global Conditioning Phase-A Trip (Operate) Global Conditioning Phase-B Trip (Operate) Global Conditioning Phase-C Trip (Operate) IEC61850 Data Attribute Name LD0.LEDPTRC1.Op.general LD0.LEDPTRC1.Op.phsA

LD0.LEDPTRC1.Op.phsB

LD0.LEDPTRC1.Op.phsC

Table 11:
Coil Addr 5020 5021 5022 5023 5024 5025 5026 5027 5028 5029 5030 5031 5032 5033 5034 5035 5036 5037 5038 5039 5040 5041 Register(:Bit) Addr 2476:0 2476:1 2476:2 2476:3 2476:4 2476:5 2476:6 2476:7 2476:8 2476:9 2476:10 2476:11 2476:12 2476:13 2476:14 2476:15 2477:0 2477:1 2477:2 2477:3 2477:4 2477:5 Dc 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes MCD

LED Status (LEDGGIO1)


Type Scale Offset Description Led 1 On Led 2 On Led 3 On Led 4 On Led 5 On Led 6 On Led 7 On Led 8 On Led 9 On Led 10 On Led 11 On IEC61850 Data Attribute Name LD0.LEDGGIO1.SPCSO1.stVal LD0.LEDGGIO1.SPCSO2.stVal LD0.LEDGGIO1.SPCSO3.stVal LD0.LEDGGIO1.SPCSO4.stVal LD0.LEDGGIO1.SPCSO5.stVal LD0.LEDGGIO1.SPCSO6.stVal LD0.LEDGGIO1.SPCSO7.stVal LD0.LEDGGIO1.SPCSO8.stVal LD0.LEDGGIO1.SPCSO9.stVal LD0.LEDGGIO1.SPCSO10.stVal LD0.LEDGGIO1.SPCSO11.stVal

RET615 ANSI Point List Manual

17

Section 2 Modbus data mappings

1MAC207644-MB B

Table 12:
Coil Addr 2148 2149 2150 2151 2152 2153 2154 2155 2156 2157 2158 2159 Register(:Bit) Addr 2162:0 2162:1 2162:2 2162:3 2162:4 2162:5 2162:6 2162:7 2162:8 2162:9 2162:10 2162:11 Dc 2 2 2 2 2 2 2 2 2 2 2 2 Yes Yes Yes Yes Yes Yes MCD

X100 - Binary Inputs/Outputs (XGGIO100)


Type Scale Offset Description X100-Output 1 PSM X100-Output 2 PSM X100-Output 3 PSM X100-Output 4 PSM X100-Output 5 PSM X100-Output 6 PSM IEC61850 Data Attribute Name LD0.XGGIO100.SPCSO1.stVal LD0.XGGIO100.SPCSO2.stVal LD0.XGGIO100.SPCSO3.stVal LD0.XGGIO100.SPCSO4.stVal LD0.XGGIO100.SPCSO5.stVal LD0.XGGIO100.SPCSO6.stVal

Table 13:
Coil Addr 2132 2133 2134 2135 2136 2137 2138 2139 2164 2165 2166 2167 2168 2169 2170 2171 2172 2173 2174 2175 2176 2177 2178 2320:0 2320:1 2320:2 2320:3 2320:4 2320:5 2320:6 2320:7 2320:8 2320:9 2320:10 2320:11 2320:12 2320:13 2320:14 Input Addr (1x) Register(:Bit) Addr Dc 2 2 2 2 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

X110 - Binary Inputs/Outputs (XGGIO110)


MCD Type Scale Offset Description X110-Output 1 BIO Yes X110-Output 2 BIO Yes X110-Output 3 BIO Yes X110-Output 4 BIO Yes X110-Input 1 BIO Yes X110-Input 2 BIO Yes X110-Input 3 BIO Yes X110-Input 4 BIO Yes X110-Input 5 BIO Yes X110-Input 6 BIO Yes X110-Input 7 BIO Yes X110-Input 8 BIO LD0.XGGIO110.Ind8.stVal LD0.XGGIO110.Ind7.stVal LD0.XGGIO110.Ind6.stVal LD0.XGGIO110.Ind5.stVal LD0.XGGIO110.Ind4.stVal LD0.XGGIO110.Ind3.stVal LD0.XGGIO110.Ind2.stVal LD0.XGGIO110.Ind1.stVal LD0.XGGIO110.SPCSO4.stVal LD0.XGGIO110.SPCSO3.stVal LD0.XGGIO110.SPCSO2.stVal IEC61850 Data Attribute Name LD0.XGGIO110.SPCSO1.stVal

18

RET615 ANSI Point List Manual

1MAC207644-MB B

Section 2 Modbus data mappings

Coil Addr

Input Addr (1x) 2179

Register(:Bit) Addr 2320:15

Dc 1

MCD Yes

Type

Scale

Offset

Description

IEC61850 Data Attribute Name

Table 14:
Coil Addr 2100 2101 2102 2103 2104 2105 2100 2101 2102 2103 2104 2105 2106 2107 2108 2109 2110 2111 2316:0 2316:1 2316:2 2316:3 2316:4 2316:5 2316:6 2316:7 2316:8 2316:9 2316:10 2316:11 Input Addr (1x) Register(:Bit) Addr Dc 2 2 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1

X130 - Binary Inputs/Outputs (XGGIO130)


MCD Type Scale Offset Description X130-Output 1 Yes X130-Output 2 Yes X130-Output 3 Yes X130-Input 1 Yes X130-Input 2 Yes X130-Input 3 Yes X130-Input 4 Yes X130-Input 5 Yes X130-Input 6 Yes LD0.XGGIO130.Ind6.stVal LD0.XGGIO130.Ind5.stVal LD0.XGGIO130.Ind4.stVal LD0.XGGIO130.Ind3.stVal LD0.XGGIO130.Ind2.stVal LD0.XGGIO130.Ind1.stVal LD0.XGGIO130.SPCSO3.stVal LD0.XGGIO130.SPCSO2.stVal IEC61850 Data Attribute Name LD0.XGGIO130.SPCSO1.stVal

Table 15:
Coil Addr 2230 2231 3400 3401 3402 3403 3404 3405 Register(:Bit) Addr 2167:0 2167:1 2224:0 2224:1 2224:2 2224:3 2224:4 2224:5 2326:0 2326:1 Dc 0 0 0 0 0 0 0 0 0 0 Yes Yes Yes Yes Yes MCD

51P (1):Three-phase non-directional overcurrent protection - low stage - instance 1 (PHLPTOC1)


Type Scale Offset Description 51P (1) Trip (Operate) 51P (1) Phase A Trip (Operate) 51P (1) Phase B Trip (Operate) 51P (1) Phase C Trip (Operate) 51P (1) Enable Signal For Current Multiplier IEC61850 Data Attribute Name LD0.PHLPTOC1.Op.general LD0.PHLPTOC1.Op.phsA LD0.PHLPTOC1.Op.phsB LD0.PHLPTOC1.Op.phsC LD0.PHLPTOC1.InEnaMult.stVal

RET615 ANSI Point List Manual

19

Section 2 Modbus data mappings

1MAC207644-MB B

Table 16:
Coil Addr 2836 2837 3532 3533 3534 3535 3536 3537 Register(:Bit) Addr 2195:8 2195:9 2232:4 2232:5 2232:6 2232:7 2232:8 2232:9 Dc 0 0 0 0 0 0 0 0 Yes Yes Yes Yes MCD

51P (2):Three-phase non-directional overcurrent protection - low stage - instance 2 (PHLPTOC2)


Type Scale Offset Description 51P (2) Trip (Operate) 51P (2) Phase A Trip (Operate) 51P (2) Phase B Trip (Operate) 51P (2) Phase C Trip (Operate) IEC61850 Data Attribute Name LD0.PHLPTOC2.Op.general LD0.PHLPTOC2.Op.phsA LD0.PHLPTOC2.Op.phsB LD0.PHLPTOC2.Op.phsC

Table 17:
Register(:Bit) Addr 2167:2 2167:3 2224:6 2224:7 2224:8 2224:9 2224:10 2224:11 2326:2 2326:3

50P-1 (1):Three-phase non-directional overcurrent protection - high stage - instance 1 (PHHPTOC1) Type Scale Offset Description 50P-1 (1) Trip (Operate) IEC61850 Data Attribute Name LD0.PHHPTOC1.Op.general LD0.PHHPTOC1.Op.phsA LD0.PHHPTOC1.Op.phsB LD0.PHHPTOC1.Op.phsC LD0.PHHPTOC1.InEnaMult.stVa l

Coil Addr 2232 2233 3406 3407 3408 3409 3410 3411

Dc 0 0 0 0 0 0 0 0 0 0

MCD

Yes 50P-1 (1) Phase A Trip (Operate) Yes 50P-1 (1) Phase B Trip (Operate) Yes 50P-1 (1) Phase C Trip (Operate) Yes 50P-1 (1) Enable Signal For Current Multiplier Yes

Table 18:
Register(:Bit) Addr 2167:4 2167:5 2224:12 2224:13 2224:14 2224:15 2225:0 2225:1 2326:4 2326:5

50P-1 (2):Three-phase non-directional overcurrent protection - high stage - instance 2 (PHHPTOC2)


Type Scale Offset Description 50P-1 (2) Trip (Operate) IEC61850 Data Attribute Name LD0.PHHPTOC2.Op.general LD0.PHHPTOC2.Op.phsA LD0.PHHPTOC2.Op.phsB LD0.PHHPTOC2.Op.phsC LD0.PHHPTOC2.InEnaMult.stVa l

Coil Addr 2234 2235 3412 3413 3414 3415 3416 3417

Dc 0 0 0 0 0 0 0 0 0 0

MCD

Yes 50P-1 (2) Phase A Trip (Operate) Yes 50P-1 (2) Phase B Trip (Operate) Yes 50P-1 (2) Phase C Trip (Operate) Yes 50P-1 (2) Enable Signal For Current Multiplier Yes

20

RET615 ANSI Point List Manual

1MAC207644-MB B

Section 2 Modbus data mappings

Table 19:
Register(:Bit) Addr 2195:10 2195:11 2232:10 2232:11 2232:12 2232:13 2232:14 2232:15

50P-2 (1):Three-phase non-directional overcurrent protection - high stage - instance 3 (PHHPTOC3)


Type Scale Offset Description 50P-2 (1) Trip (Operate) IEC61850 Data Attribute Name LD0.PHHPTOC3.Op.general LD0.PHHPTOC3.Op.phsA LD0.PHHPTOC3.Op.phsB LD0.PHHPTOC3.Op.phsC

Coil Addr 2838 2839 3538 3539 3540 3541 3542 3543

Dc 0 0 0 0 0 0 0 0

MCD

Yes 50P-2 (1) Phase A Trip (Operate) Yes 50P-2 (1) Phase B Trip (Operate) Yes 50P-2 (1) Phase C Trip (Operate) Yes

Table 20:
Register(:Bit) Addr 2195:12 2195:13 2233:0 2233:1 2233:2 2233:3 2233:4 2233:5

Table - 50P-2 (2):Three-phase non-directional overcurrent protection - high stage - instance 4 (PHHPTOC4))
Type Scale Offset Description 50P-2 (2) Trip (Operate) IEC61850 Data Attribute Name LD0.PHHPTOC4.Op.general LD0.PHHPTOC4.Op.phsA LD0.PHHPTOC4.Op.phsB LD0.PHHPTOC4.Op.phsC

Coil Addr 2840 2841 3544 3545 3546 3547 3548 3549

Dc 0 0 0 0 0 0 0 0

MCD

Yes 50P-2 (2) Phase A Trip (Operate) Yes 50P-2 (2) Phase B Trip (Operate) Yes 50P-2 (2) Phase C Trip (Operate) Yes

Table 21:
Coil Addr 2270 2271 3460 3461 3462 3463 3464 3465 Register(:Bit) Addr 2169:8 2169:9 2227:12 2227:13 2227:14 2227:15 2228:0 2228:1 Dc 0 0 0 0 0 0 0 0 Yes Yes Yes Yes MCD

67/51P (2):Three-phase directional overcurrent protection - low stage - instance 1 (DPHLPTOC1)


Type Scale Offset Description 67/51P (2) Trip (Operate) 67/51P (2) Phase A Trip (Operate) 67/51P (2) Phase B Trip (Operate) 67/51P (2) Phase C Trip (Operate) IEC61850 Data Attribute Name LD0.DPHLPTOC1.Op.general LD0.DPHLPTOC1.Op.phsA LD0.DPHLPTOC1.Op.phsB LD0.DPHLPTOC1.Op.phsC

Table 22:
Coil Addr 2272 2273 3466 3467 Register(:Bit) Addr 2169:10 2169:11 2228:2 2228:3 Dc 0 0 0 0 Yes Yes MCD

67/51P (1):Three-phase directional overcurrent protection - low stage - instance 2 (DPHLPTOC2)


Type Scale Offset Description 67/51P (1) Trip (Operate) 67/51P (1) Phase A Trip (Operate) IEC61850 Data Attribute Name LD0.DPHLPTOC2.Op.general LD0.DPHLPTOC2.Op.phsA

RET615 ANSI Point List Manual

21

Section 2 Modbus data mappings

1MAC207644-MB B

Coil Addr 3468 3469 3470 3471

Register(:Bit) Addr 2228:4 2228:5 2228:6 2228:7

Dc 0 0 0 0

MCD

Type

Scale

Offset

Description 67/51P (1) Phase B Trip (Operate)

IEC61850 Data Attribute Name LD0.DPHLPTOC2.Op.phsB LD0.DPHLPTOC2.Op.phsC

Yes 67/51P (1) Phase C Trip (Operate) Yes

Table 23:
Coil Addr 2246 2247 Register(:Bit) Addr 2168:0 2168:1 2326:8 2326:9 Dc 0 0 0 0 Yes Yes MCD

51G:Non-directional ground-fault protection - low stage - instance 1 (EFLPTOC1)


Type Scale Offset Description 51G Trip (Operate) 51G Enable Current Multiplier IEC61850 Data Attribute Name LD0.EFLPTOC1.Op.general LD0.EFLPTOC1.InEnaMult.stVal

Table 24:
Coil Addr 2238 2239 Register(:Bit) Addr 2167:8 2167:9 Dc 0 0 Yes MCD

51N (1):Non-directional ground-fault protection - low stage - instance 2 (EFLPTOC2)


Type Scale Offset Description 51N (1) Trip (Operate) IEC61850 Data Attribute Name LD0.EFLPTOC2.Op.general

Table 25:
Coil Addr 2602 2603 Register(:Bit) Addr 2184:8 2184:9 Dc 0 0 Yes MCD

51N (2):Non-directional ground-fault protection - low stage - instance 3 (EFLPTOC3)


Type Scale Offset Description 51N (2) Trip (Operate) IEC61850 Data Attribute Name LD0.EFLPTOC3.Op.general

Table 26:
Coil Addr 2248 2249 Register(:Bit) Addr 2168:2 2168:3 2326:10 2326:11 Dc 0 0 0 0 Yes Yes MCD

50G-1:Non-directional ground-fault protection - high stage - instance 1 (EFHPTOC1)


Type Scale Offset Description 50G-1 Trip (Operate) 50G-1 Enable Current Multiplier IEC61850 Data Attribute Name LD0.EFHPTOC1.Op.general LD0.EFHPTOC1.InEnaMult.stVa l

Table 27:
Coil Addr 2250 2251 Register(:Bit) Addr 2168:4 2168:5 Dc 0 0 Yes MCD

50G-2:Non-directional ground-fault protection - high stage - instance 2 (EFHPTOC2)


Type Scale Offset Description 50G-2 Trip (Operate) IEC61850 Data Attribute Name LD0.EFHPTOC2.Op.general

22

RET615 ANSI Point List Manual

1MAC207644-MB B

Section 2 Modbus data mappings

Table 28:
Coil Addr 2240 2241 Register(:Bit) Addr 2167:10 2167:11 Dc 0 0 Yes MCD

50N-1 (1):Non-directional ground-fault protection - high stage - instance 3 (EFHPTOC3)


Type Scale Offset Description 50N-1 (1) Trip (Operate) IEC61850 Data Attribute Name LD0.EFHPTOC3.Op.general

Table 29:
Coil Addr 2242 2243 Register(:Bit) Addr 2167:12 2167:13 Dc 0 0 Yes MCD

50N-1 (2):Non-directional ground-fault protection - high stage - instance 4 (EFHPTOC4)


Type Scale Offset Description 50N-1 (2) Trip (Operate) IEC61850 Data Attribute Name LD0.EFHPTOC4.Op.general

Table 30:
Coil Addr 2296 2297 Register(:Bit) Addr 2171:2 2171:3 Dc 0 0 Yes MCD

50N-2 (1):Non-directional ground-fault protection - high stage - instance 5 (EFHPTOC5)


Type Scale Offset Description 50N-2 (1) Trip (Operate) IEC61850 Data Attribute Name LD0.EFHPTOC5.Op.general

Table 31:
Coil Addr 2624 2625 Register(:Bit) Addr 2185:14 2185:15 Dc 0 0 Yes MCD

50N-2 (2):Non-directional ground-fault protection - high stage - instance 6 (EFHPTOC6)


Type Scale Offset Description 50N-2 (2) Trip (Operate) IEC61850 Data Attribute Name LD0.EFHPTOC6.Op.general

Table 32:
Coil Addr 2278 2279 Register(:Bit) Addr 2170:0 2170:1 Dc 0 0 Yes MCD

67/51N (2):Directional ground-fault protection - low stage - instance 1 (DEFLPTOC1)


Type Scale Offset Description 67/51N (2) Trip (Operate) IEC61850 Data Attribute Name LD0.DEFLPTOC1.Op.general

Table 33:
Coil Addr 2280 2281 Register(:Bit) Addr 2170:2 2170:3 Dc 0 0 Yes MCD

67/51N (1):Directional ground-fault protection - low stage - instance 2 (DEFLPTOC2)


Type Scale Offset Description 67/51N (1) Trip (Operate) IEC61850 Data Attribute Name LD0.DEFLPTOC2.Op.general

Table 34:
Coil Addr 2256 2257 Register(:Bit) Addr 2168:10 2168:11 2326:14 2326:15 Dc 0 0 0 0 Yes Yes MCD

46 (1):Negative-sequence overcurrent protection - instance 1 (NSPTOC1)


Type Scale Offset Description 46 (1) Trip (Operate) 46 (1) Enable Signal For Current Multiplier IEC61850 Data Attribute Name LD0.NSPTOC1.Op.general LD0.NSPTOC1.InEnaMult.stVal

RET615 ANSI Point List Manual

23

Section 2 Modbus data mappings

1MAC207644-MB B

Table 35:
Coil Addr 2258 2259 Register(:Bit) Addr 2168:12 2168:13 2327:0 2327:1 Dc 0 0 0 0 Yes Yes MCD

46 (2):Negative-sequence overcurrent protection - instance 2 (NSPTOC2)


Type Scale Offset Description 46 (2) Trip (Operate) 46 (2) Enable Signal For Current Multiplier IEC61850 Data Attribute Name LD0.NSPTOC2.Op.general LD0.NSPTOC2.InEnaMult.stVal

Table 36:
Coil Addr 2308 2309 Register(:Bit) Addr 2171:14 2171:15 Dc 0 0 Yes MCD

59G (2):Residual overvoltage protection - instance 1 (ROVPTOV1)


Type Scale Offset Description 59G (2) Trip (Operate) IEC61850 Data Attribute Name LD0.ROVPTOV1.Op.general

Table 37:
Coil Addr 3146 3147 Register(:Bit) Addr 2210:12 2210:13 Dc 0 0 Yes MCD

59N (2):Residual overvoltage protection - instance 2 (ROVPTOV2)


Type Scale Offset Description 59N (2) Trip (Operate) IEC61850 Data Attribute Name LD0.ROVPTOV2.Op.general

Table 38:
Coil Addr 2348 2349 Register(:Bit) Addr 2174:6 2174:7 Dc 0 0 Yes MCD

59N (1):Residual overvoltage protection - instance 3 (ROVPTOV3)


Type Scale Offset Description 59N (1) Trip (Operate) IEC61850 Data Attribute Name LD0.ROVPTOV3.Op.general

Table 39:
Coil Addr 2350 2351 Register(:Bit) Addr 2174:8 2174:9 Dc 0 0 Yes MCD

59G (1):Residual overvoltage protection - instance 4 (ROVPTOV4)


Type Scale Offset Description 59G (1) Trip (Operate) IEC61850 Data Attribute Name LD0.ROVPTOV4.Op.general

Table 40:
Coil Addr 2292 2293 3478 3479 3480 3481 3482 3483 Register(:Bit) Addr 2170:14 2170:15 2228:14 2228:15 2229:0 2229:1 2229:2 2229:3 Dc 0 0 0 0 0 0 0 0 Yes Yes Yes Yes MCD

27 (2):Three-phase undervoltage protection - instance 1 (PHPTUV1)


Type Scale Offset Description 27 (2) Trip (Operate) 27 (2) Phase A Trip (Operate) 27 (2) Phase B Trip (Operate) 27 (2) Phase C Trip (Operate) IEC61850 Data Attribute Name LD0.PHPTUV1.Op.general LD0.PHPTUV1.Op.phsA LD0.PHPTUV1.Op.phsB LD0.PHPTUV1.Op.phsC

24

RET615 ANSI Point List Manual

1MAC207644-MB B

Section 2 Modbus data mappings

Table 41:
Coil Addr 2294 2295 3484 3485 3486 3487 3488 3489 Register(:Bit) Addr 2171:0 2171:1 2229:4 2229:5 2229:6 2229:7 2229:8 2229:9 Dc 0 0 0 0 0 0 0 0 Yes Yes Yes Yes MCD

27 (1):Three-phase undervoltage protection - instance 2 (PHPTUV2)


Type Scale Offset Description 27 (1) Trip (Operate) 27 (1) Phase A Trip (Operate) 27 (1) Phase B Trip (Operate) 27 (1) Phase C Trip (Operate) IEC61850 Data Attribute Name LD0.PHPTUV2.Op.general LD0.PHPTUV2.Op.phsA LD0.PHPTUV2.Op.phsB LD0.PHPTUV2.Op.phsC

Table 42:
Coil Addr 2298 2299 3490 3491 3492 3493 3494 3495 Register(:Bit) Addr 2171:4 2171:5 2229:10 2229:11 2229:12 2229:13 2229:14 2229:15 Dc 0 0 0 0 0 0 0 0 Yes Yes Yes Yes MCD

59 (2):Three-phase overvoltage protection - instance 1 (PHPTOV1)


Type Scale Offset Description 59 (2) Trip (Operate) 59 (2) Phase A Trip (Operate) 59 (2) Phase B Trip (Operate) 59 (2) Phase C Trip (Operate) IEC61850 Data Attribute Name LD0.PHPTOV1.Op.general LD0.PHPTOV1.Op.phsA LD0.PHPTOV1.Op.phsB LD0.PHPTOV1.Op.phsC

Table 43:
Coil Addr 2300 2301 3496 3497 3498 3499 3500 3501 Register(:Bit) Addr 2171:6 2171:7 2230:0 2230:1 2230:2 2230:3 2230:4 2230:5 Dc 0 0 0 0 0 0 0 0 Yes Yes Yes Yes MCD

59 (1):Three-phase overvoltage protection - instance 2 (PHPTOV2))


Type Scale Offset Description 59 (1) Trip (Operate) 59 (1) Phase A Trip (Operate) 59 (1) Phase B Trip (Operate) 59 (1) Phase C Trip (Operate) IEC61850 Data Attribute Name LD0.PHPTOV2.Op.general LD0.PHPTOV2.Op.phsA LD0.PHPTOV2.Op.phsB LD0.PHPTOV2.Op.phsC

Table 44:
Coil Addr 2342 2343 Register(:Bit) Addr 2174:0 2174:1 Dc 0 0 Yes MCD

47 (2):Negative-sequence overvoltage protection - instance 1 (NSPTOV1))


Type Scale Offset IEC61850 Data Attribute Name LD0.NSPTOV1.Op.general Description 47 (2) Trip (Operate)

RET615 ANSI Point List Manual

25

Section 2 Modbus data mappings

1MAC207644-MB B

Table 45:
Coil Addr 3152 3153 Register(:Bit) Addr 2211:2 2211:3 Dc 0 0 Yes MCD

47 (1):Negative-sequence overvoltage protection - instance 2 (NSPTOV2))


Type Scale Offset Description 47 (1) Trip (Operate) IEC61850 Data Attribute Name LD0.NSPTOV2.Op.general

Table 46:
Coil Addr 3154 3155 Register(:Bit) Addr 2211:4 2211:5 841 Dc 0 0 6 Yes MCD

81-1 (2):Frequency protection - instance 1 (FRPTRC1)


Type Scale Offset Description 81-1 (2) Frequency Trip (Operate) u16 100 0 81-1 (2) Ratio Of Pickup (Start) Time / Trip (Operate) Time Instance 1 IEC61850 Data Attribute Name LD0.FRPTRC1.Op.general LD0.FRPTRC1.StrDur.mag.f

Table 47:
Coil Addr 3158 3159 Register(:Bit) Addr 2211:8 2211:9 843 Dc 0 0 6 Yes MCD

81-1 (2):Frequency protection - instance 1 (FRPTOF1)


Type Scale Offset Description 81-1 (2) Over-Frequency Trip (Operate) u16 100 0 81-1 (2) Ratio Of Pickup (Start) Time / Trip (Operate) Time Overfrequency Instance 1 IEC61850 Data Attribute Name LD0.FRPTOF1.Op.general

LD0.FRPTOF1.StrDur.mag.f

Table 48:
Coil Addr 3162 3163 Register(:Bit) Addr 2211:12 2211:13 845 Dc 0 0 6 Yes MCD

81-1 (2):Frequency protection - instance 1 (FRPTUF1)


Type Scale Offset Description 81-1 (2) Under-Frequency Trip (Operate) u16 100 0 81-1 (2) Ratio Of Pickup (Start) Time / Trip (Operate) Time Underfrequency Instance 1 IEC61850 Data Attribute Name LD0.FRPTUF1.Op.general

LD0.FRPTUF1.StrDur.mag.f

Table 49:
Coil Addr 3166 3167 Register(:Bit) Addr 2212:0 2212:1 847 Dc 0 0 6 Yes MCD

81-1 (2):Frequency protection - instance 1 (FRPFRC1)


Type Scale Offset Description 81-1 (2) Frequency Gradient Trip (Operate) u16 100 0 81-1 (2) Ratio Of Pickup (Start) Time / Trip (Operate) Time Frequency Gradient Instance 1 IEC61850 Data Attribute Name LD0.FRPFRC1.Op.general

LD0.FRPFRC1.StrDur.mag.f

26

RET615 ANSI Point List Manual

1MAC207644-MB B

Section 2 Modbus data mappings

Table 50:
Coil Addr 3156 3157 Register(:Bit) Addr 2211:6 2211:7 842 Dc 0 0 6 Yes MCD

81-2 (2):Frequency protection - instance 2 (FRPTRC2)


Type Scale Offset Description 81-2 (2) Frequency Trip (Operate) u16 100 0 81-2 (2) Ratio Of Pickup (Start) Time / Trip (Operate) Time Instance 2 IEC61850 Data Attribute Name LD0.FRPTRC2.Op.general LD0.FRPTRC2.StrDur.mag.f

Table 51:
Coil Addr 3160 3161 Register(:Bit) Addr 2211:10 2211:11 844 Dc 0 0 6 Yes MCD

81-2 (2):Frequency protection - instance 2 (FRPTOF2)


Type Scale Offset Description 81-2 (2) Over-Frequency Trip (Operate) u16 100 0 81-2 (2) Ratio Of Pickup (Start) Time / Trip (Operate) Time Overfrequency Instance 2 IEC61850 Data Attribute Name LD0.FRPTOF2.Op.general

LD0.FRPTOF2.StrDur.mag.f

Table 52:
Coil Addr 3164 3165 Register(:Bit) Addr 2211:14 2211:15 846 Dc 0 0 6 Yes MCD

81-2 (2):Frequency protection - instance 2 (FRPTUF2)


Type Scale Offset Description 81-2 (2) Under-Frequency Trip (Operate) u16 100 0 81-2 (2) Ratio Of Pickup (Start) Time / Trip (Operate) Time Underfrequency Instance 2 IEC61850 Data Attribute Name LD0.FRPTUF2.Op.general

LD0.FRPTUF2.StrDur.mag.f

Table 53:
Coil Addr 3168 3169 Register(:Bit) Addr 2212:2 2212:3 848 Dc 0 0 6 Yes MCD

81-2 (2):Frequency protection - instance 2 (FRPFRC2)


Type Scale Offset Description 81-2 (2) Frequency Gradient Trip (Operate) u16 100 0 81-2 (2) Ratio Of Pickup (Start) Time / Trip (Operate) Time Frequency Gradient Instance 2 IEC61850 Data Attribute Name LD0.FRPFRC2.Op.general

LD0.FRPFRC2.StrDur.mag.f

Table 54:
Coil Addr 3252 3253 Register(:Bit) Addr 2217:6 2217:7 881 Dc 0 0 6 Yes MCD

81-1 (1):Frequency protection - instance 3 (FRPTRC3)


Type Scale Offset Description 81-1 (1) Trip (Operate) u16 100 0 81-1 (1) Ratio Of Pickup (Start) Time / Trip (Operate) Time IEC61850 Data Attribute Name LD0.FRPTRC3.Op.general LD0.FRPTRC3.StrDur.mag.f

RET615 ANSI Point List Manual

27

Section 2 Modbus data mappings

1MAC207644-MB B

Table 55:
Coil Addr 3256 3257 Register(:Bit) Addr 2217:10 2217:11 883 Dc 0 0 6 Yes MCD

81-1 (1):Frequency protection - instance 3 (FRPTOF3)


Type Scale Offset Description 81-1 (1) Over-Frequency Trip (Operate) u16 100 0 81-1 (1) Ratio Of Pickup (Start) Time / Trip (Operate) Time Overfrequency IEC61850 Data Attribute Name LD0.FRPTOF3.Op.general

LD0.FRPTOF3.StrDur.mag.f

Table 56:
Coil Addr 3260 3261 Register(:Bit) Addr 2217:14 2217:15 885 Dc 0 0 6 Yes MCD

81-1 (1):Frequency protection - instance 3 (FRPTUF3)


Type Scale Offset Description 81-1 (1) Under-Frequency Trip (Operate) u16 100 0 81-1 (1) Ratio Of Pickup (Start) Time / Trip (Operate) Time Underfrequency IEC61850 Data Attribute Name LD0.FRPTUF3.Op.general

LD0.FRPTUF3.StrDur.mag.f

Table 57:
Coil Addr 3248 3249 Register(:Bit) Addr 2217:2 2217:3 879 Dc 0 0 6 Yes MCD

81-1 (1):Frequency protection - instance 3 (FRPFRC3)


Type Scale Offset Description 81-1 (1) Frequency Gradient Trip (Operate) u16 100 0 81-1 (1) Ratio Of Pickup (Start) Time / Trip (Operate) Time Frequency Gradient IEC61850 Data Attribute Name LD0.FRPFRC3.Op.general

LD0.FRPFRC3.StrDur.mag.f

Table 58:
Coil Addr 3254 3255 Register(:Bit) Addr 2217:8 2217:9 882 Dc 0 0 6 Yes MCD

81-2 (1):Frequency protection - instance 4 (FRPTRC4)


Type Scale Offset Description 81-2 (1) Trip (Operate) u16 100 0 81-2 (1) Ratio Of Pickup (Start) Time / Trip (Operate) Time IEC61850 Data Attribute Name LD0.FRPTRC4.Op.general LD0.FRPTRC4.StrDur.mag.f

Table 59:
Coil Addr 3258 3259 Register(:Bit) Addr 2217:12 2217:13 884 Dc 0 0 6 Yes MCD

81-2 (1):Frequency protection - instance 4 (FRPTOF4)


Type Scale Offset Description 81-2 (1) Over-Frequency Trip (Operate) u16 100 0 81-2 (1) Ratio Of Pickup (Start) Time / Trip (Operate) Time Overfrequency IEC61850 Data Attribute Name LD0.FRPTOF4.Op.general

LD0.FRPTOF4.StrDur.mag.f

28

RET615 ANSI Point List Manual

1MAC207644-MB B

Section 2 Modbus data mappings

Table 60:
Coil Addr 3262 3263 Register(:Bit) Addr 2218:0 2218:1 886 Dc 0 0 6 Yes MCD

81-2 (1):Frequency protection - instance 4 (FRPTUF4)


Type Scale Offset Description 81-2 (1) Under-Frequency Trip (Operate) u16 100 0 81-2 (1) Ratio Of Pickup (Start) Time / Trip (Operate) Time Underfrequency IEC61850 Data Attribute Name LD0.FRPTUF4.Op.general

LD0.FRPTUF4.StrDur.mag.f

Table 61:
Coil Addr 3250 3251 Register(:Bit) Addr 2217:4 2217:5 880 Dc 0 0 6 Yes MCD

81-2 (1):Frequency protection - instance 4 (FRPFRC4)


Type Scale Offset Description 81-2 (1) Frequency Gradient Trip (Operate) u16 100 0 81-2 (1) Ratio Of Pickup (Start) Time / Trip (Operate) Time Frequency Gradient IEC61850 Data Attribute Name LD0.FRPFRC4.Op.general

LD0.FRPFRC4.StrDur.mag.f

Table 62:
Coil Addr 3224 3225 Register(:Bit) Addr 2215:10 2215:11 Dc 0 0 Yes MCD

24-1 (2):Voltage per hertz protection - instance 1 (OEPVPH1)


Type Scale Offset Description 24-1 (2) Trip (Operate) IEC61850 Data Attribute Name LD0.OEPVPH1.Op.general

Table 63:
Coil Addr 3226 3227 Register(:Bit) Addr 2215:12 2215:13 Dc 0 0 Yes MCD

24-2 (2):Voltage per hertz protection - instance 2 (OEPVPH2)


Type Scale Offset Description 24-2 (2) Trip (Operate) IEC61850 Data Attribute Name LD0.OEPVPH2.Op.general

Table 64:
Coil Addr 3228 3229 Register(:Bit) Addr 2215:14 2215:15 Dc 0 0 Yes MCD

24-1 (1):Voltage per hertz protection - instance 3 (OEPVPH3)


Type Scale Offset Description 24-1 (1) Trip (Operate) IEC61850 Data Attribute Name LD0.OEPVPH3.Op.general

Table 65:
Coil Addr 3230 3231 Register(:Bit) Addr 2216:0 2216:1 Dc 0 0 Yes MCD

24-2 (1):Voltage per hertz protection - instance 4 (OEPVPH4)


Type Scale Offset Description 24-2 (1) Trip (Operate) IEC61850 Data Attribute Name LD0.OEPVPH4.Op.general

RET615 ANSI Point List Manual

29

Section 2 Modbus data mappings

1MAC207644-MB B

Table 66:
Register(:Bit) Addr 2195:4

49T (1):Three-phase thermal overload protection for power transformers - two time constants (T2PTTR1)
Type Scale Offset Description 49T (1) Thermal Overload Protection Trip (Operate) For Power Transformers IEC61850 Data Attribute Name LD0.T2PTTR1.Op.general

Coil Addr 2832

Dc 0

MCD

2833 5512

2195:5 2505:6

0 0

Yes 49T (1) Thermal Overload Protection Alarm For Power Transformers Yes u16 u16 u16 u16 u16 100 100 100 1 1 0 0 0 0 0 49T (1) Temp 49T (1) Temp_Rl 49T (1) The Ambient Temperature Used In The Calculation 49T (1) Estimated Time To Trip (Operate) 49T (1) Estimated Time To Deactivate Inhrec LD0.T2PTTR1.Tmp.mag.f LD0.T2PTTR1.TmpRl.mag.f LD0.T2PTTR1.TmpUsed.mag.f LD0.T2PTTR1.TmsOp.stVal LD0.T2PTTR1.TmsRecEna.stVa l LD0.T2PTTR1.AlmThm.general

5513

2505:7 792 793 794 795 796

0 6 6 6 0 0

Table 67:
Coil Addr 2828 2829 3830 3831 3832 3833 3834 3835 3836 3837 3838 3839 3840 3841 3842 3843 Register(:Bit) Addr 2195:0 2195:1 2245:14 2245:15 2246:0 2246:1 2246:2 2246:3 2246:4 2246:5 2246:6 2246:7 2246:8 2246:9 2246:10 2246:11 797 Dc 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 6 Yes Yes Yes Yes Yes Yes Yes Yes MCD

87T:Stabilized and instantaneous differential protection for 2W transformers (TR2PDIF1)


Type Scale Offset Description 87T Trip (Operate) Signal 87T Phase-A Differential Trip (Operate) 87T Phase-B Differential Trip (Operate) 87T Phase-C Differential Trip (Operate) 87T Status From 2nd Harmonic Restraint Blocking- General IEC61850 Data Attribute Name LD0.TR2PDIF1.Op.general LD0.TR2PDIF1.Op.phsA

LD0.TR2PDIF1.Op.phsB

LD0.TR2PDIF1.Op.phsC

LD0.TR2PDIF1.Blk2HSt.general

87T Status From 2nd Harmonic Restraint Blocking- Phase A

LD0.TR2PDIF1.Blk2HSt.phsA

87T Status From 2nd Harmonic Restraint Blocking- Phase B

LD0.TR2PDIF1.Blk2HSt.phsB

87T Status From 2nd Harmonic Restraint Blocking- Phase C

LD0.TR2PDIF1.Blk2HSt.phsC

u16

100

87T Phase A Differential Current

LD0.TR2PDIF1.DifAClc.phsA.cV al.mag.f

30

RET615 ANSI Point List Manual

1MAC207644-MB B

Section 2 Modbus data mappings

Coil Addr

Register(:Bit) Addr 798 799 800 801 802

Dc 6 6 6 6 6

MCD

Type u16 u16 u16 u16 u16

Scale 100 100 100 100 100

Offset 0 0 0 0 0

Description 87T Phase B Differential Current 87T Phase C Differential Current 87T Phase A Biasing Current 87T Phase B Biasing Current 87T Phase C Biasing Current

IEC61850 Data Attribute Name LD0.TR2PDIF1.DifAClc.phsB.cV al.mag.f LD0.TR2PDIF1.DifAClc.phsC.cV al.mag.f LD0.TR2PDIF1.RstA.phsA.cVal. mag.f LD0.TR2PDIF1.RstA.phsB.cVal. mag.f LD0.TR2PDIF1.RstA.phsC.cVal. mag.f

Table 68:
Register(:Bit) Addr 2198:14 2198:15

Table - 87LOZREF (2):Numerical stabilized low impedance restricted ground-fault protection (LREFPDIF1)
Type Scale Offset Description 87LOZREF (2) Trip (Operate) IEC61850 Data Attribute Name LD0.LREFPDIF1.Op.general

Coil Addr 2890 2891

Dc 0 0

MCD

Yes

Table 69:
Coil Addr 2310 2311 2312 2313 5526 5527 5528 5529 5532 5533 Register(:Bit) Addr 2172:0 2172:1 2172:2 2172:3 2506:4 2506:5 2506:6 2506:7 2506:10 2506:11 Dc 0 0 0 0 0 0 0 0 0 0 Yes Yes Yes Yes Yes MCD

50BF (1):Circuit breaker failure protection - instance 1 (CCBRBRF1)


Type Scale Offset Description 50BF (1) Recloser External Operation Failure 2 IEC61850 Data Attribute Name LD0.CCBRBRF1.OpEx.general

50BF (1) Recloser Retrip (Internal Trip) 2 50BF (1) Recloser Close Position 2 50BF (1) Recloser Faulty And Unable To Trip 2

LD0.CCBRBRF1.OpIn.general

LD0.CCBRBRF1.InPosCls.stVal LD0.CCBRBRF1.InCBFlt.stVal

50BF (1) Recloser Trip Start 2

LD0.CCBRBRF1.InStr.stVal

Table 70:
Coil Addr 6548 6549 6550 6551 6552 6553 Register(:Bit) Addr 3034:4 3034:5 3034:6 3034:7 3034:8 3034:9 Dc 0 0 0 0 0 0 Yes Yes Yes MCD

50BF (2):Circuit breaker failure protection - instance 2 (CCBRBRF2)


Type Scale Offset Description 50BF (2) Recloser Faulty And Unable To Trip 1 IEC61850 Data Attribute Name LD0.CCBRBRF2.InCBFlt.stVal

50BF (2) Recloser Close Position 1 50BF (2) Recloser Trip Start 1

LD0.CCBRBRF2.InPosCls.stVal LD0.CCBRBRF2.InStr.stVal

RET615 ANSI Point List Manual

31

Section 2 Modbus data mappings

1MAC207644-MB B

Coil Addr 6554 6555 6556 6557

Register(:Bit) Addr 3034:10 3034:11 3034:12 3034:13

Dc 0 0 0 0

MCD

Type

Scale

Offset

Description 50BF (2) Recloser External Operation Failure 1

IEC61850 Data Attribute Name LD0.CCBRBRF2.OpEx.general

Yes 50BF (2) Recloser Retrip (Internal Trip) 1 Yes LD0.CCBRBRF2.OpIn.general

Table 71:
Coil Addr 2896 2897 2898 2899 Register(:Bit) Addr 2199:4 2199:5 2199:6 2199:7 Dc 0 0 0 0 Yes Yes MCD

86/94-1:Master trip - instance 1 (TRPPTRC1)


Type Scale Offset Description 86/94-1 Master Trip Trip (Operate) Input 1 86/94-1 Master Trip General Output 1 IEC61850 Data Attribute Name LD0.TRPPTRC1.Op.general

LD0.TRPPTRC1.Tr.general

Table 72:
Coil Addr 2900 2901 2902 2903 Register(:Bit) Addr 2199:8 2199:9 2199:10 2199:11 Dc 0 0 0 0 Yes Yes MCD

86/94-2:Master trip - instance 2 (TRPPTRC2)


Type Scale Offset Description 86/94-2 Master Trip Operate Input 2 86/94-2 Master Trip General Output 2 IEC61850 Data Attribute Name LD0.TRPPTRC2.Op.general LD0.TRPPTRC2.Tr.general

Table 73:
Coil Addr 2320 2321 2326 2327 Register(:Bit) Addr 2172:10 2172:11 2173:0 2173:1 Dc 0 0 0 0 Yes Yes MCD

AFD-1 (2):Arc protection - instance 1 (ARCSARC11)


Type Scale Offset Description AFD-1 (2) Fault Arc Detected 1 AFD-1 (2) Remote Fault Arc Detected 1 IEC61850 Data Attribute Name LD0.ARCSARC11.FADet.stVal LD0.ARCSARC11.InRemFA.stVa l

Table 74:
Coil Addr 2314 2315 2172:4 2172:5 Register(:Bit) Addr Dc 0 0 0 0 Yes Yes MCD

AFD-1 (2):Arc protection - instance 1 (ARCPTRC11)


Type Scale Offset Description AFD-1 (2) Arc Detected Trip (Operate) 1 AFD-1 (2) Arc Detected Trip (Operate) 1 IEC61850 Data Attribute Name LD0.ARCPTRC11.Op.general

LD0.ARCPTRC11.Op.general

32

RET615 ANSI Point List Manual

1MAC207644-MB B

Section 2 Modbus data mappings

Table 75:
Coil Addr 2322 2323 2328 2329 Register(:Bit) Addr 2172:12 2172:13 2173:2 2173:3 Dc 0 0 0 0 Yes Yes MCD

AFD-2 (2):Arc protection - instance 2 (ARCSARC21)


Type Scale Offset Description AFD-2 (2) Fault Arc Detected 2 AFD-2 (2) Remote Fault Arc Detected 2 IEC61850 Data Attribute Name LD0.ARCSARC21.FADet.stVal LD0.ARCSARC21.InRemFA.stV al

Table 76:
Coil Addr 2316 2317 Register(:Bit) Addr 2172:6 2172:7 Dc 0 0 Yes MCD

AFD-2 (2):Arc protection - instance 2 (ARCPTRC21)


Type Scale Offset Description AFD-2 (2) Arc Detected Trip (Operate) 2 IEC61850 Data Attribute Name LD0.ARCPTRC21.Op.general

Table 77:
Coil Addr 2324 2325 2330 2331 Register(:Bit) Addr 2172:14 2172:15 2173:4 2173:5 Dc 0 0 0 0 Yes Yes MCD

AFD-3 (2):Arc protection - instance 3 (ARCSARC31)


Type Scale Offset Description AFD-3 (2) Fault Arc Detected 3 AFD-3 (2) Remote Fault Arc Detected 3 IEC61850 Data Attribute Name LD0.ARCSARC31.FADet.stVal LD0.ARCSARC31.InRemFA.stV al

Table 78:
Coil Addr 2318 2319 Register(:Bit) Addr 2172:8 2172:9 Dc 0 0 Yes MCD

AFD-3 (2):Arc protection - instance 3 (ARCPTRC31)


Type Scale Offset Description AFD-3 (2) Arc Detected Trip (Operate) 3 IEC61850 Data Attribute Name LD0.ARCPTRC31.Op.general

Table 79:
Coil Addr 3218 3219 Register(:Bit) Addr 2215:4 2215:5 Dc 0 0 Yes MCD

MAP - 1:Multi-purpose protection - instance 1 (MAPGAPC1)


Type Scale Offset Description MAP - 1 Multi-Purpose Protection 1 IEC61850 Data Attribute Name LD0.MAPGAPC1.Op.general

Table 80:
Coil Addr 3220 3221 Register(:Bit) Addr 2215:6 2215:7 Dc 0 0 Yes MCD

MAP - 2:Multi-purpose protection - instance 2 (MAPGAPC2)


Type Scale Offset Description MAP - 2 Multi-Purpose Protection 2 IEC61850 Data Attribute Name LD0.MAPGAPC2.Op.general

RET615 ANSI Point List Manual

33

Section 2 Modbus data mappings

1MAC207644-MB B

Table 81:
Coil Addr 3222 3223 Register(:Bit) Addr 2215:8 2215:9 Dc 0 0 Yes MCD

MAP - 3:Multi-purpose protection - instance 3 (MAPGAPC3)


Type Scale Offset Description MAP - 3 Multi-Purpose Protection 3 IEC61850 Data Attribute Name LD0.MAPGAPC3.Op.general

Table 82:
Coil Addr 3170 3171 3172 3173 Register(:Bit) Addr 2212:4 2212:5 2212:6 2212:7 849 Dc 0 0 0 0 6 Yes Yes MCD

81LSH-1 (2):Load shedding and restoration - instance 1 (LSHDPTRC1)


Type Scale Offset Description 81LSH-1 (2)Load Shedding Trip - 1 81LSH-1 (2)Restore Signal For Load Restoring Purposes - 1 IEC61850 Data Attribute Name LD0.LSHDPTRC1.Op.general LD0.LSHDPTRC1.RestLodOp.g eneral

u16

100

81LSH-1 (2) Ratio Of Pickup (Start) / Trip (Operate) Time Frequency Gradient 1

LD0.LSHDPTRC1.StrDur.mag.f

Table 83:
Coil Addr 3178 3179 Register(:Bit) Addr 2212:12 2212:13 Dc 0 0 Yes MCD

81LSH-1 (2):Load shedding and restoration - instance 1 (LSHDPTUF1)


Type Scale Offset Description 81LSH-1 (2) Trip (Operate) Underfrequency IEC61850 Data Attribute Name LD0.LSHDPTUF1.Op.general

Table 84:
Coil Addr 3182 3183 Register(:Bit) Addr 2213:0 2213:1 Dc 0 0 Yes MCD

81LSH-1 (2):Load shedding and restoration - instance 1 (LSHDPFRC1)


Type Scale Offset Description 81LSH-1 (2) Trip (Operate) Frequency Gradient IEC61850 Data Attribute Name LD0.LSHDPFRC1.Op.general

Table 85:
Coil Addr 3174 3175 3176 3177 Register(:Bit) Addr 2212:8 2212:9 2212:10 2212:11 850 Dc 0 0 0 0 6 Yes Yes MCD

81LSH-2 (2):Load shedding and restoration - instance 2 (LSHDPTRC2)


Type Scale Offset Description 81LSH-2 (2) Load Shedding Trip - 2 81LSH-2 (2) Restore Signal For Load Restoring Purposes - 2 IEC61850 Data Attribute Name LD0.LSHDPTRC2.Op.general LD0.LSHDPTRC2.RestLodOp.g eneral

u16

100

81LSH-2 (2) Ratio Of Pickup (Start) / Trip (Operate) Time Frequency Gradient 2

LD0.LSHDPTRC2.StrDur.mag.f

34

RET615 ANSI Point List Manual

1MAC207644-MB B

Section 2 Modbus data mappings

Table 86:
Coil Addr 3180 3181 Register(:Bit) Addr 2212:14 2212:15 Dc 0 0 Yes MCD

81LSH-2 (2):Load shedding and restoration - instance 2 (LSHDPTUF2)


Type Scale Offset Description 81LSH-2 (2) Trip (Operate) Underfrequency IEC61850 Data Attribute Name LD0.LSHDPTUF2.Op.general

Table 87:
Coil Addr 3184 3185 Register(:Bit) Addr 2213:2 2213:3 Dc 0 0 Yes MCD

81LSH-2 (2):Load shedding and restoration - instance 2 (LSHDPFRC2)


Type Scale Offset Description 81LSH-2 (2) Trip (Operate) Frequency Gradient IEC61850 Data Attribute Name LD0.LSHDPFRC2.Op.general

Table 88:
Coil Addr 3232 3233 3234 3235 Register(:Bit) Addr 2216:2 2216:3 2216:4 2216:5 851 Dc 0 0 0 0 6 Yes Yes MCD

81LSH-1 (1):Load shedding and restoration - instance 3 (LSHDPTRC3)


Type Scale Offset Description 81LSH-1 (1) Load Shedding Trip - 3 81LSH-1 (1) Restore Signal For Load Restoring Purposes - 3 IEC61850 Data Attribute Name LD0.LSHDPTRC3.Op.general LD0.LSHDPTRC3.RestLodOp.g eneral

u16

100

81LSH-1 (1) Ratio Of Pickup (Start) / Trip (Operate) Time Frequency Gradient 3

LD0.LSHDPTRC3.StrDur.mag.f

Table 89:
Coil Addr 3244 3245 Register(:Bit) Addr 2216:14 2216:15 Dc 0 0 Yes MCD

81LSH-1 (1):Load shedding and restoration - instance 3 (LSHDPTUF3)


Type Scale Offset Description 81LSH-1 (1) Trip (Operate) Underfrequency IEC61850 Data Attribute Name LD0.LSHDPTUF3.Op.general

Table 90:
Coil Addr 3240 3241 Register(:Bit) Addr 2216:10 2216:11 Dc 0 0 Yes MCD

81LSH-1 (1):Load shedding and restoration - instance 3 (LSHDPFRC3)


Type Scale Offset Description 81LSH-1 (1) Trip (Operate) Frequency Gradient IEC61850 Data Attribute Name LD0.LSHDPFRC3.Op.general

RET615 ANSI Point List Manual

35

Section 2 Modbus data mappings

1MAC207644-MB B

Table 91:
Coil Addr 3236 3237 3238 3239 Register(:Bit) Addr 2216:6 2216:7 2216:8 2216:9 852 Dc 0 0 0 0 6 Yes Yes MCD

81LSH-2 (1):Load shedding and restoration - instance 4 (LSHDPTRC4)


Type Scale Offset Description 81LSH-2 (1)Load Shedding Trip - 4 81LSH-2 (1) Restore Signal For Load Restoring Purposes - 4 IEC61850 Data Attribute Name LD0.LSHDPTRC4.Op.general LD0.LSHDPTRC4.RestLodOp.g eneral

u16

100

81LSH-2 (1) Ratio Of Pickup (Start) / Trip (Operate) Time Frequency Gradient 4

LD0.LSHDPTRC4.StrDur.mag.f

Table 92:
Coil Addr 3246 3247 Register(:Bit) Addr 2217:0 2217:1 Dc 0 0 Yes MCD

81LSH-2 (1):Load shedding and restoration - instance 4 (LSHDPTUF4)


Type Scale Offset Description 81LSH-2 (1) Trip (Operate) Underfrequency IEC61850 Data Attribute Name LD0.LSHDPTUF4.Op.general

Table 93:
Coil Addr 3242 3243 Register(:Bit) Addr 2216:12 2216:13 Dc 0 0 Yes MCD

81LSH-2 (1):Load shedding and restoration - instance 4 (LSHDPFRC4)


Type Scale Offset Description 81LSH-2 (1) Trip (Operate) Frequency Gradient IEC61850 Data Attribute Name LD0.LSHDPFRC4.Op.general

Table 94:
Coil Addr 2950 2951 3586 3587 3588 3589 3590 3591 Register(:Bit) Addr 2202:10 2202:11 2235:10 2235:11 2235:12 2235:13 2235:14 2235:15 Dc 0 0 0 0 0 0 0 0 Yes Yes Yes Yes MCD

37 (1):Loss of phase - instance 1 (PHPTUC1)


Type Scale Offset Description 37 (1) Trip (Operate) 37 (1) Phase-A Trip (Operate) 37 (1) Phase-B Trip (Operate) 37 (1) Phase-C Trip (Operate) IEC61850 Data Attribute Name LD0.PHPTUC1.Op.general LD0.PHPTUC1.Op.phsA LD0.PHPTUC1.Op.phsB LD0.PHPTUC1.Op.phsC

36

RET615 ANSI Point List Manual

1MAC207644-MB B

Section 2 Modbus data mappings

Table 95:
Coil Addr 5442 5443 5444 5445 5472 5473 Register(:Bit) Addr 2501:0 2501:1 2501:2 2501:3 2502:14 2502:15 Dc 0 0 0 0 0 0 Yes Yes Yes MCD

52 (1):Circuit-breaker control - instance 1 (CBCILO1)


Type Scale Offset Description 52 (1) Breaker Interlock Enable Open 1 52 (1) Breaker Interlock Enable Close 1 52 (1) Breaker Interlock Bypass 1 IEC61850 Data Attribute Name CTRL.CBCILO1.EnaOpn.stVal

CTRL.CBCILO1.EnaCls.stVal

CTRL.CBCILO1.ItlByPss.stVal

Table 96:
Coil Addr 5110 5111 5112 5113 5114 5115 Register(:Bit) Addr 2481:0 2481:1 2481:2 2481:3 2481:4 2481:5 Dc 0 0 0 0 0 0 Yes Yes Yes MCD

52 (1):Circuit-breaker control - instance 1 (CBCSWI1)


Type Scale Offset Description 52 (1) Breaker Switch Position Open 52 (1) Breaker Switch Position Closed 52 (1) Breaker Switch Position valid IEC61850 Data Attribute Name CTRL.CBCSWI1.Pos.stVal CTRL.CBCSWI1.Pos.stVal

CTRL.CBCSWI1.Pos.stVal

Table 97:
Coil Addr 5150 5151 5152 5153 Register(:Bit) Addr 2490:0 2490:1 2490:2 2490:3 Dc 0 0 0 0 Yes Yes MCD

52 (1):Circuit-breaker control - instance 1 (CBXCBR1)


Type Scale Offset Description 52 (1) Breaker Block Open 52 (1) Breaker Block Close IEC61850 Data Attribute Name CTRL.CBXCBR1.BlkOpn.stVal CTRL.CBXCBR1.BlkCls.stVal

Table 98:
Coil Addr 6558 6559 6560 6561 6562 6563 Register(:Bit) Addr 3034:14 3034:15 3035:0 3035:1 3035:2 3035:3 Dc 0 0 0 0 0 0 Yes Yes Yes MCD

52 (2):Circuit-breaker control - instance 2 (CBCILO2)


Type Scale Offset Description 52 (2) Breaker Interlock Enable Open 2 52 (2) Breaker Interlock Enable Close 2 52 (2) Breaker Interlock Bypass 2 IEC61850 Data Attribute Name CTRL.CBCILO2.EnaOpn.stVal

CTRL.CBCILO2.EnaCls.stVal

CTRL.CBCILO2.ItlByPss.stVal

RET615 ANSI Point List Manual

37

Section 2 Modbus data mappings

1MAC207644-MB B

Table 99:
Coil Addr 5140 5141 5142 5143 5144 5145 Register(:Bit) Addr 2486:0 2486:1 2486:2 2486:3 2486:4 2486:5 Dc 0 0 0 0 0 0 Yes Yes Yes MCD

52 (2):Circuit-breaker control - instance 2 (CBCSWI2)


Type Scale Offset Description 52 (2) Breaker Switch Position Open 52 (2) Breaker Switch Position Closed 52 (2) Breaker Switch Position valid IEC61850 Data Attribute Name CTRL.CBCSWI2.Pos.stVal CTRL.CBCSWI2.Pos.stVal

CTRL.CBCSWI2.Pos.stVal

Table 100:
Coil Addr 5154 5155 5156 5157 Register(:Bit) Addr 2490:4 2490:5 2490:6 2490:7 Dc 0 0 0 0 Yes Yes MCD

52 (2):Circuit-breaker control - instance 2 (CBXCBR2)


Scale Offset Description 52 (2) Breaker Block Open 52 (2) Breaker Block Close IEC61850 Data Attribute Name CTRL.CBXCBR2.BlkOpn.stVal CTRL.CBXCBR2.BlkCls.stVal

Type

Table 101:
Coil Addr Register(:Bit) Addr 813 Dc 6 MCD

84T:Tap changer position indication (TPOSSLTC1)


Scale 1 Offset 0 Description 84T TAPPOS IEC61850 Data Attribute Name LD0.TPOSSLTC1.TapPos.valW Tr.posVal

Type u16

Table 102:
Coil Addr 5410 5411 5412 5413 5418 5419 5420 5421 5422 5423 5424 5425 Register(:Bit) Addr 2499:0 2499:1 2499:2 2499:3 2499:8 2499:9 2499:10 2499:11 2499:12 2499:13 2499:14 2499:15 Dc 0 0 0 0 0 0 0 0 0 0 0 0 Yes Yes Yes Yes Yes Yes MCD

52CM (1):Circuit-breaker condition monitoring - instance 1 (SSCBR1)


Scale Offset Description 52CM (1) Recloser Open Travel Time Exceeded Set Value IEC61850 Data Attribute Name LD0.SSCBR1.OpnAlm.stVal

Type

52CM (1) Recloser Close Travel Time Exceeded Set Value

LD0.SSCBR1.ClsAlm.stVal

52CM (1) Spring Charging Time Has Crossed The Set Value

LD0.SSCBR1.SprChaAlm.stVal

52CM (1) Number Of Recloser Operations Exceeds Alarm Limit

LD0.SSCBR1.OpNumAlm.stVal

52CM (1) Number Of Recloser Operations Exceeds Lockout Limit

LD0.SSCBR1.OpNumLO.stVal

52CM (1) Accumulated Currents Power (Iyt) Exceeded Alarm Limit

LD0.SSCBR1.APwrAlm.stVal

38

RET615 ANSI Point List Manual

1MAC207644-MB B

Section 2 Modbus data mappings

Coil Addr 5426 5427 5428 5429 5430 5431 5432 5433 5434 5435 5436 5437 5438 5439 5440 5441 5534 5535 5536 5537 5538 5539 5540 5541 5542 5543 5544 5545

Register(:Bit) Addr 2500:0 2500:1 2500:2 2500:3 2500:4 2500:5 2500:6 2500:7 2500:8 2500:9 2500:10 2500:11 2500:12 2500:13 2500:14 2500:15 2506:12 2506:13 2506:14 2506:15 2507:0 2507:1 2507:2 2507:3 2507:4 2507:5 2507:6 2507:7 834 835 836

Dc 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 6 6 6

MCD

Type

Scale

Offset

Description 52CM (1) Accumulated Currents Power (Iyt) Exceeded Lockout Limit

IEC61850 Data Attribute Name LD0.SSCBR1.APwrLO.stVal

Yes 52CM (1) Remaining Life Of Recloser Exceeded Alarm Limit Yes 52CM (1) Recloser Not Operated For Long Time Alarm Yes 52CM (1) Pressure Below Alarm Level Yes 52CM (1) Pressure Below Lockout Level Yes 52CM (1) Recloser Position Is Open Yes 52CM (1) Invalid Position Yes 52CM (1) Recloser Position Is Closed Yes 52CM (1) Recloser Spring Charging Started Input Yes 52CM (1) Recloser Spring Charged Input Yes 52CM (1) Binary Pressure Input For Alarm Yes 52CM (1) Binary Pressure Input For Lockout Indication Yes 52CM (1) Posopen Yes 52CM (1) Posclose Yes u16 u16 u16 100 100 100 0 0 0 52CM (1) Travel Time Of The Recloser During Opening Operation 52CM (1) Travel Time Of The Recloser During Closing Operation 52CM (1) The Charging Time Of The Recloser Spring LD0.SSCBR1.TmmsOpn.mag.f LD0.SSCBR1.TmmsCls.mag.f LD0.SSCBR1.TmsSprCha.mag.f LD0.SSCBR1.InPosCls.stVal LD0.SSCBR1.InPosOpn.stVal LD0.SSCBR1.InPresLO.stVal LD0.SSCBR1.InPresAlm.stVal LD0.SSCBR1.InSprCha.stVal LD0.SSCBR1.InSprChStr.stVal LD0.SSCBR1.PosCls.stVal LD0.SSCBR1.PosIvd.stVal LD0.SSCBR1.PosOpn.stVal LD0.SSCBR1.PresLO.stVal LD0.SSCBR1.PresAlm.stVal LD0.SSCBR1.LonTmAlm.stVal LD0.SSCBR1.CBLifAlm.stVal

RET615 ANSI Point List Manual

39

Section 2 Modbus data mappings

1MAC207644-MB B

Coil Addr

Register(:Bit) Addr 2010 2011 2012 2013 2014 2015 2016 2018 2020 2022

Dc 5 5 5 5 5 5 0 0 0 4

MCD

Type s32

Scale 1

Offset 0

Description 52CM (1) Phase A Accumulated Currents Power (Iyt)

IEC61850 Data Attribute Name LD0.SSCBR1.AccAPwrPhA.mag .f

s32

52CM (1) Phase B Accumulated Currents Power (Iyt)

LD0.SSCBR1.AccAPwrPhB.mag .f

s32

52CM (1) Phase C Accumulated Currents Power (Iyt)

LD0.SSCBR1.AccAPwrPhC.mag .f

u16 u16 u16 u16

1 1 1 1

0 0 0 0

52CM (1) Phase A Recloser Monitoring Remaining Life 52CM (1) Phase B Recloser Monitoring Remaining Life 52CM (1) Phase C Recloser Monitoring Remaining Life 52CM (1) The Number Of Days Recloser Has Been Inactive

LD0.SSCBR1.RmnLifPhA.stVal LD0.SSCBR1.RmnLifPhB.stVal LD0.SSCBR1.RmnLifPhC.stVal LD0.SSCBR1.InaTmdCnt.stVal

Table 103:
Coil Addr 6564 6565 6566 6567 6572 6573 6574 6575 6576 6577 6578 6579 6580 6581 6582 6583 Register(:Bit) Addr 3035:4 3035:5 3035:6 3035:7 3035:12 3035:13 3035:14 3035:15 3036:0 3036:1 3036:2 3036:3 3036:4 3036:5 3036:6 3036:7 Dc 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Yes Yes Yes Yes Yes Yes Yes Yes MCD

52CM (2):Circuit-breaker condition monitoring - instance 2 (SSCBR2)


Scale Offset Description 52CM (2) Recloser Open Travel Time Exceeded Set Value IEC61850 Data Attribute Name LD0.SSCBR2.OpnAlm.stVal

Type

52CM (2) Recloser Close Travel Time Exceeded Set Value

LD0.SSCBR2.ClsAlm.stVal

52CM (2) Spring Charging Time Has Crossed The Set Value

LD0.SSCBR2.SprChaAlm.stVal

52CM (2) Number Of Recloser Operations Exceeds Alarm Limit

LD0.SSCBR2.OpNumAlm.stVal

52CM (2) Number Of Recloser Operations Exceeds Lockout Limit

LD0.SSCBR2.OpNumLO.stVal

52CM (2) Accumulated Currents Power (Iyt) Exceeded Alarm Limit

LD0.SSCBR2.APwrAlm.stVal

52CM (2) Accumulated Currents Power (Iyt) Exceeded Lockout Limit

LD0.SSCBR2.APwrLO.stVal

52CM (2) Remaining Life Of Recloser Exceeded Alarm Limit

LD0.SSCBR2.CBLifAlm.stVal

40

RET615 ANSI Point List Manual

1MAC207644-MB B

Section 2 Modbus data mappings

Coil Addr 6584 6585 6586 6587 6588 6589 6590 6591 6592 6593 6594 6595 6596 6597 6598 6599 6600 6601 6602 6603 6604 6605 6606 6607

Register(:Bit) Addr 3036:8 3036:9 3036:10 3036:11 3036:12 3036:13 3036:14 3036:15 3037:0 3037:1 3037:2 3037:3 3037:4 3037:5 3037:6 3037:7 3037:8 3037:9 3037:10 3037:11 3037:12 3037:13 3037:14 3037:15 871 872 873 2135 2136 2137 2138

Dc 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 6 6 6 5 5 5 5

MCD

Type

Scale

Offset

Description 52CM (2) Recloser Not Operated For Long Time Alarm

IEC61850 Data Attribute Name LD0.SSCBR2.LonTmAlm.stVal

Yes 52CM (2) Pressure Below Alarm Level Yes 52CM (2) Pressure Below Lockout Level Yes 52CM (2) Recloser Position Is Open Yes 52CM (2) Invalid Position Yes 52CM (2) Recloser Position Is Closed Yes 52CM (2) Recloser Spring Charging Started Input Yes 52CM (2) Recloser Spring Charged Input Yes 52CM (2) Binary Pressure Input For Alarm Yes 52CM (2) Binary Pressure Input For Lockout Indication Yes 52CM (2) Posopen Yes 52CM (2) Posclose Yes u16 u16 u16 s32 100 100 100 1 0 0 0 0 52CM (2) Travel Time Of The Recloser During Opening Operation 52CM (2) Travel Time Of The Recloser During Closing Operation 52CM (2) The Charging Time Of The Recloser Spring 52CM (2) Phase A Accumulated Currents Power (Iyt) LD0.SSCBR2.TmmsOpn.mag.f LD0.SSCBR2.TmmsCls.mag.f LD0.SSCBR2.TmsSprCha.mag.f LD0.SSCBR2.AccAPwrPhA.mag .f LD0.SSCBR2.InPosCls.stVal LD0.SSCBR2.InPosOpn.stVal LD0.SSCBR2.InPresLO.stVal LD0.SSCBR2.InPresAlm.stVal LD0.SSCBR2.InSprCha.stVal LD0.SSCBR2.InSprChStr.stVal LD0.SSCBR2.PosCls.stVal LD0.SSCBR2.PosIvd.stVal LD0.SSCBR2.PosOpn.stVal LD0.SSCBR2.PresLO.stVal LD0.SSCBR2.PresAlm.stVal

s32

52CM (2) Phase B Accumulated Currents Power (Iyt)

LD0.SSCBR2.AccAPwrPhB.mag .f

RET615 ANSI Point List Manual

41

Section 2 Modbus data mappings

1MAC207644-MB B

Coil Addr

Register(:Bit) Addr 2139 2140 2141 2143 2145

Dc 5 5 0 0 0

MCD

Type s32

Scale 1

Offset 0

Description 52CM (2) Phase C Accumulated Currents Power (Iyt)

IEC61850 Data Attribute Name LD0.SSCBR2.AccAPwrPhC.mag .f

u16 u16 u16

1 1 1

0 0 0

52CM (2) Phase A Recloser Monitoring Remaining Life 52CM (2) Phase B Recloser Monitoring Remaining Life 52CM (2) Phase C Recloser Monitoring Remaining Life

LD0.SSCBR2.RmnLifPhA.stVal LD0.SSCBR2.RmnLifPhB.stVal LD0.SSCBR2.RmnLifPhC.stVal

Table 104:
Coil Addr 5474 5475 Register(:Bit) Addr 2503:0 2503:1 Dc 0 0 Yes MCD

TCM-1:Trip circuit supervision - instance 1 (TCSSCBR1)


Scale Offset Description TCM-1 Trip Circuit Supervision Alarm 1 IEC61850 Data Attribute Name LD0.TCSSCBR1.CirAlm.stVal

Type

Table 105:
Coil Addr 5476 5477 Register(:Bit) Addr 2503:2 2503:3 Dc 0 0 Yes MCD

TCM-2:Trip circuit supervision - instance 2 (TCSSCBR2)


Scale Offset Description TCM-2 Trip Circuit Supervision Alarm 2 IEC61850 Data Attribute Name LD0.TCSSCBR2.CirAlm.stVal

Type

Table 106:
Coil Addr 2956 2957 2958 Register(:Bit) Addr 2203:0 2203:1 2203:2 Dc 0 0 0 Yes MCD

MCS 3I-I2:Advanced current circuit supervision for transformers (CTSRCTF1)


Scale Offset Description MCS 3I I2 Advanced Current Circuit Supervision For Transformers IEC61850 Data Attribute Name LD0.CTSRCTF1.Op.general

Type

MCS 3I I2 Group 1 Advanced Current Circuit Supervision For Transformers Yes MCS 3I I2 Group 2 Advanced Current Circuit Supervision For Transformers Yes MCS 3I I2 Group 3 Advanced Current Circuit Supervision For Transformers Yes

LD0.CTSRCTF1.OpGrp1.genera l

2959 2960

2203:3 2203:4

0 0

LD0.CTSRCTF1.OpGrp2.genera l

2961 2962

2203:5 2203:6

0 0

LD0.CTSRCTF1.OpGrp3.genera l

2963

2203:7

Table 107:
Coil Addr 5446 5447 Register(:Bit) Addr 2501:4 2501:5 Dc 0 0 Yes MCD

IA-IB-IC (1):Three-phase current measurement - instance 1 (CMMXU1)


Scale Offset Description IA IB IC (1) High Alarm IEC61850 Data Attribute Name LD0.CMMXU1.HiAlm.stVal

Type

42

RET615 ANSI Point List Manual

1MAC207644-MB B

Section 2 Modbus data mappings

5448 5449 5450 5451 5452 5453

2501:6 2501:7 2501:8 2501:9 2501:10 2501:11 536 537 538 539 540 541

0 0 0 0 0 0 6 6 6 6 6 6 u32 100 0 u32 100 0 Yes u32 100 0 Yes Yes

IA IB IC (1) High Warning IA IB IC (1) Low Warning IA IB IC (1) Low Alarm IA IB IC (1) Phase A Mag (RMS)

LD0.CMMXU1.HiWrn.stVal LD0.CMMXU1.LoWrn.stVal LD0.CMMXU1.LoAlm.stVal LD0.CMMXU1.A.phsA.instCVal. mag.f LD0.CMMXU1.A.phsB.instCVal. mag.f LD0.CMMXU1.A.phsC.instCVal. mag.f

IA IB IC (1) Phase B Mag (RMS)

IA IB IC (1) Phase C Mag (RMS)

Table 108:
Coil Addr Register(:Bit) Addr 899 900 901 902 903 904 1000 1001 1002 Dc 5 5 5 5 5 5 5 5 5 MCD

IA-IB-IC (1):Three-phase current measurement - instance 1 (CMSTA1)


Scale 100 Offset 0 Description IA IB IC (1) Phase A Average Demand IA IB IC (1) Phase B Average Demand IA IB IC (1) Phase C Average Demand IA IB IC (1) Phase A Maximum Demand IA IB IC (1) Phase A Maximum Demand Timestamp Year(High Byte)/Month(Low Byte) Day(High Byte)/Hour(Low Byte) Min(High Byte)/Sec(Low Byte) MilliSecond Time Quality IEC61850 Data Attribute Name LD0.CMSTA1.AvAmpsA.mag.f

Type u32

u32

100

LD0.CMSTA1.AvAmpsB.mag.f

u32

100

LD0.CMSTA1.AvAmpsC.mag.f

u32

100

LD0.CMSTA1.MaxAmpsA.mag.f

1003 1004 1005 1006 1010 1011 1012

5 5 5 5 5 5 5 u32 100 0

IA IB IC (1) Phase B Maximum Demand IA IB IC (1) Phase B Maximum Demand Timestamp Year(High Byte)/Month(Low Byte) Day(High Byte)/Hour(Low Byte) Min(High Byte)/Sec(Low Byte) MilliSecond

LD0.CMSTA1.MaxAmpsB.mag.f

1013 1014 1015

5 5 5

RET615 ANSI Point List Manual

43

Section 2 Modbus data mappings

1MAC207644-MB B

Coil Addr

Register(:Bit) Addr 1016 1020 1021 1022

Dc

MCD

Type

Scale

Offset

Description Time Quality

IEC61850 Data Attribute Name

5 5 5

u32

100

IA IB IC (1) Phase C Maximum Demand IA IB IC (1) Phase C Maximum Demand Timestamp Year(High Byte)/Month(Low Byte) Day(High Byte)/Hour(Low Byte) Min(High Byte)/Sec(Low Byte) MilliSecond Time Quality

LD0.CMSTA1.MaxAmpsC.mag.f

1023 1024 1025 1026

5 5 5 5

Table 109:
Coil Addr 5486 5487 5488 5489 5490 5491 5492 5493 Register(:Bit) Addr 2503:12 2503:13 2503:14 2503:15 2504:0 2504:1 2504:2 2504:3 548 549 550 551 552 553 Dc 0 0 0 0 0 0 0 0 6 6 6 6 6 6 Yes Yes Yes Yes MCD

IA-IB-IC (2):Three-phase current measurement - instance 2 (CMMXU2)


Scale Offset Description IA IB IC (2) High Alarm IA IB IC (2) High Warning IA IB IC (2) Low Warning IA IB IC (2) Low Alarm IEC61850 Data Attribute Name LD0.CMMXU2.HiAlm.stVal LD0.CMMXU2.HiWrn.stVal LD0.CMMXU2.LoWrn.stVal LD0.CMMXU2.LoAlm.stVal LD0.CMMXU2.A.phsA.instCVal. mag.f LD0.CMMXU2.A.phsB.instCVal. mag.f LD0.CMMXU2.A.phsC.instCVal. mag.f

Type

u32

100

IA IB IC (2) Phase A Mag (RMS)

u32

100

IA IB IC (2) Phase B Mag (RMS)

u32

100

IA IB IC (2) Phase C Mag (RMS)

Table 110:
Coil Addr Register(:Bit) Addr 907 908 909 910 911 912 Dc 5 5 5 5 5 5 MCD

IA-IB-IC (2):Three-phase current measurement - instance 2 (CMSTA2)


Scale 100 Offset 0 Description IA IB IC (2) Phase A Average Demand IA IB IC (2) Phase B Average Demand IA IB IC (2) Phase C Average Demand IEC61850 Data Attribute Name LD0.CMSTA2.AvAmpsA.mag.f

Type u32

u32

100

LD0.CMSTA2.AvAmpsB.mag.f

u32

100

LD0.CMSTA2.AvAmpsC.mag.f

44

RET615 ANSI Point List Manual

1MAC207644-MB B

Section 2 Modbus data mappings

Coil Addr

Register(:Bit) Addr 1120 1121 1122

Dc 5 5

MCD

Type u32

Scale 100

Offset 0

Description IA IB IC (2) Phase A Maximum Demand IA IB IC (2) Phase A Maximum Demand Timestamp Year(High Byte)/Month(Low Byte) Day(High Byte)/Hour(Low Byte) Min(High Byte)/Sec(Low Byte) MilliSecond Time Quality

IEC61850 Data Attribute Name LD0.CMSTA2.MaxAmpsA.mag.f

1123 1124 1125 1126 1130 1131 1132 5 5 u32 100 0

IA IB IC (2) Phase B Maximum Demand IA IB IC (2) Phase B Maximum Demand Timestamp Year(High Byte)/Month(Low Byte) Day(High Byte)/Hour(Low Byte) Min(High Byte)/Sec(Low Byte) MilliSecond Time Quality

LD0.CMSTA2.MaxAmpsB.mag.f

1133 1134 1135 1136 1140 1141 1142 5 5 u32 100 0

IA IB IC (2) Phase C Maximum Demand IA IB IC (2) Phase C Maximum Demand Timestamp Year(High Byte)/Month(Low Byte) Day(High Byte)/Hour(Low Byte) Min(High Byte)/Sec(Low Byte) MilliSecond Time Quality

LD0.CMSTA2.MaxAmpsC.mag.f

1143 1144 1145 1146

Table 111:
Coil Addr Register(:Bit) Addr 614 615 616 617 618 619 Dc 6 6 6 6 6 6 MCD

I1-I2-I0 (1):Sequence current measurement - instance 2 (CSMSQI1)


Scale 100 Offset 0 Description I1-I2-I0 (1) Positive Sequence Mag (RMS) I1-I2-I0 (1) Negative Sequence Mag (RMS) I1-I2-I0 (1) Zero Sequence Mag (RMS) IEC61850 Data Attribute Name LD0.CSMSQI1.SeqA.c1.instCVal .mag.f LD0.CSMSQI1.SeqA.c2.instCVal .mag.f LD0.CSMSQI1.SeqA.c3.instCVal .mag.f

Type u32

u32

100

u32

100

RET615 ANSI Point List Manual

45

Section 2 Modbus data mappings

1MAC207644-MB B

Table 112:
Coil Addr Register(:Bit) Addr 623 624 625 626 627 628 Dc 6 6 6 6 6 6 MCD

I1-I2-I0 (2):Sequence current measurement - instance 2 (CSMSQI2)


Scale 100 Offset 0 Description I1-I2-I0 (2) Positive Sequence Mag (RMS) I1-I2-I0 (2) Negative Sequence Mag (RMS) I1-I2-I0 (2) Zero Sequence Mag (RMS) IEC61850 Data Attribute Name LD0.CSMSQI2.SeqA.c1.instCVal .mag.f LD0.CSMSQI2.SeqA.c2.instCVal .mag.f LD0.CSMSQI2.SeqA.c3.instCVal .mag.f

Type u32

u32

100

u32

100

Table 113:
Coil Addr 5454 5455 5456 5457 Register(:Bit) Addr 2501:12 2501:13 2501:14 2501:15 542 Dc 0 0 0 0 6 Yes Yes MCD

IG:Residual current measurement - instance 1 (RESCMMXU1)


Scale Offset Description IG High Trip (Operate) IG High Warning IEC61850 Data Attribute Name LD0.RESCMMXU1.HiAlm.stVal LD0.RESCMMXU1.HiWrn.stVal LD0.RESCMMXU1.A.res.instCV al.mag.f

Type

u16

100

IG-Mag (RMS) 1

Table 114:
Coil Addr 5460 5461 5462 5463 5464 5465 5466 5467 Register(:Bit) Addr 2502:2 2502:3 2502:4 2502:5 2502:6 2502:7 2502:8 2502:9 590 591 592 596 597 598 Dc 0 0 0 0 0 0 0 0 6 6 6 6 6 6 Yes Yes Yes Yes MCD

VA-VB-VC (1):Three-phase voltage measurement - instance 1 (VMMXU1)


Scale Offset Description VA VB VC (1) High Trip (Operate) VA VB VC (1) High Warning VA VB VC (1) Low Warning VA VB VC (1) Low Trip (Operate) IEC61850 Data Attribute Name LD0.VMMXU1.HiAlm.stVal LD0.VMMXU1.HiWrn.stVal LD0.VMMXU1.LoWrn.stVal LD0.VMMXU1.LoAlm.stVal LD0.VMMXU1.PhV.phsA.cVal.m ag.f LD0.VMMXU1.PhV.phsB.cVal.m ag.f LD0.VMMXU1.PhV.phsC.cVal.m ag.f LD0.VMMXU1.PPV.phsAB.instC Val.mag.f LD0.VMMXU1.PPV.phsBC.instC Val.mag.f LD0.VMMXU1.PPV.phsCA.instC Val.mag.f

Type

u16 u16 u16 u16 u16 u16

100 100 100 100 100 100

0 0 0 0 0 0

VA VB VC (1) Phase A Mag VA VB VC (1) Phase B Mag VA VB VC (1) Phase C Mag VA VB VC (1) Phase AB Mag (RMS) VA VB VC (1) Phase BC Mag (RMS) VA VB VC (1) Phase CA Mag (RMS)

46

RET615 ANSI Point List Manual

1MAC207644-MB B

Section 2 Modbus data mappings

Table 115:
Coil Addr 5498 5499 5500 5501 5502 5503 5504 5505 Register(:Bit) Addr 2504:8 2504:9 2504:10 2504:11 2504:12 2504:13 2504:14 2504:15 602 603 604 608 609 610 Dc 0 0 0 0 0 0 0 0 6 6 6 6 6 6 Yes Yes Yes Yes MCD

VA-VB-VC (2):Three-phase voltage measurement - instance 2 (VMMXU2)


Scale Offset Description VA VB VC (2) High Trip (Operate) VA VB VC (2) High Warning VA VB VC (2) Low Warning VA VB VC (2) Low Trip (Operate) IEC61850 Data Attribute Name LD0.VMMXU2.HiAlm.stVal LD0.VMMXU2.HiWrn.stVal LD0.VMMXU2.LoWrn.stVal LD0.VMMXU2.LoAlm.stVal LD0.VMMXU2.PhV.phsA.cVal.m ag.f LD0.VMMXU2.PhV.phsB.cVal.m ag.f LD0.VMMXU2.PhV.phsC.cVal.m ag.f LD0.VMMXU2.PPV.phsAB.instC Val.mag.f LD0.VMMXU2.PPV.phsBC.instC Val.mag.f LD0.VMMXU2.PPV.phsCA.instC Val.mag.f

Type

u16 u16 u16 u16 u16 u16

100 100 100 100 100 100

0 0 0 0 0 0

VA VB VC (2) Phase A Mag VA VB VC (2) Phase B Mag VA VB VC (2) Phase C Mag VA VB VC (2) Phase AB Mag (RMS) VA VB VC (2) Phase BC Mag (RMS) VA VB VC (2) Phase CA Mag (RMS)

Table 116:
Coil Addr 5468 5469 5470 5471 Register(:Bit) Addr 2502:10 2502:11 2502:12 2502:13 662 Dc 0 0 0 0 6 Yes Yes MCD

VG:Residual voltage measurement - instance 1 (RESVMMXU1)


Scale Offset Description VG High Alarm VG High Warning IEC61850 Data Attribute Name LD0.RESVMMXU1.HiAlm.stVal LD0.RESVMMXU1.HiWrn.stVal LD0.RESVMMXU1.PhV.res.inst CVal.mag.f

Type

u16

100

Table 117:
Coil Addr Register(:Bit) Addr 650 651 652 Dc 6 6 6 MCD

V1-V2-V0 (1):Sequence voltage measurement - instance 1 (VSMSQI1)


Scale 100 100 100 Offset 0 0 0 Description V1 V2 V0 (1) Positive Sequence Mag (RMS) V1 V2 V0 (1) Negative Sequence Mag (RMS) V1 V2 V0 (1) Zero Sequence Mag (RMS) IEC61850 Data Attribute Name LD0.VSMSQI1.SeqV.c1.instCVal .mag.f LD0.VSMSQI1.SeqV.c2.instCVal .mag.f LD0.VSMSQI1.SeqV.c3.instCVal .mag.f

Type u16 u16 u16

RET615 ANSI Point List Manual

47

Section 2 Modbus data mappings

1MAC207644-MB B

Table 118:
Coil Addr Register(:Bit) Addr 656 657 658 Dc 6 6 6 MCD

V1-V2-V0 (2):Sequence voltage measurement - instance 2 (VSMSQI2)


Scale 100 100 100 Offset 0 0 0 Description V1 V2 V0 (2) Positive Sequence Mag (RMS) V1 V2 V0 (2) Negative Sequence Mag (RMS) V1 V2 V0 (2) Zero Sequence Mag (RMS) IEC61850 Data Attribute Name LD0.VSMSQI2.SeqV.c1.instCVal .mag.f LD0.VSMSQI2.SeqV.c2.instCVal .mag.f LD0.VSMSQI2.SeqV.c3.instCVal .mag.f

Type u16 u16 u16

Table 119:
Coil Addr Register(:Bit) Addr 668 669 670 671 672 673 676 677 678 679 680 681 704 705 706 707 708 709 716 717 718 Dc 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 s16 s16 s16 s32 s32 s32 s32 s32 s32 s32 s32 MCD

SP-SE (1):Single-phase power and energy measurement - instance 1 (SPEMMXU1)


Scale 100 Offset 0 Description SP SE (1)Phase A Active Power IEC61850 Data Attribute Name LD0.SPEMMXU1.W.phsA.cVal. mag.f LD0.SPEMMXU1.W.phsB.cVal. mag.f LD0.SPEMMXU1.W.phsC.cVal. mag.f LD0.SPEMMXU1.VAr.phsA.cVal .mag.f LD0.SPEMMXU1.VAr.phsB.cVal .mag.f LD0.SPEMMXU1.VAr.phsC.cVal .mag.f LD0.SPEMMXU1.VA.phsA.cVal. mag.f LD0.SPEMMXU1.VA.phsB.cVal. mag.f LD0.SPEMMXU1.VA.phsC.cVal. mag.f LD0.SPEMMXU1.PF.phsA.cVal. mag.f LD0.SPEMMXU1.PF.phsB.cVal. mag.f LD0.SPEMMXU1.PF.phsC.cVal. mag.f

Type s32

100

SP SE (1)Phase B Active Power

100

SP SE (1)Phase C Active Power

100

SP SE (1)Phase A Reactive Power

100

SP SE (1)Phase B Reactive Power

100

SP SE (1)Phase C Reactive Power

100

SP SE (1)Phase A Apparent Power

100

SP SE (1)Phase B Apparent Power

100

SP SE (1)Phase C Apparent Power

100 100 100

0 0 0

SP SE (1)Average A Power Factor SP SE (1)Average B Power Factor SP SE (1)Average C Power Factor

48

RET615 ANSI Point List Manual

1MAC207644-MB B

Section 2 Modbus data mappings

Table 120:
Coil Addr Register(:Bit) Addr 686 687 688 689 690 691 694 695 696 697 698 699 710 711 712 713 714 715 719 720 721 Dc 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 s16 s16 s16 s32 s32 s32 s32 s32 s32 s32 s32 MCD

SP-SE (2):Single-phase power and energy measurement - instance 2 (SPEMMXU2)


Scale 100 Offset 0 Description SP SE (2)Phase A Active Power IEC61850 Data Attribute Name LD0.SPEMMXU2.W.phsA.cVal. mag.f LD0.SPEMMXU2.W.phsB.cVal. mag.f LD0.SPEMMXU2.W.phsC.cVal. mag.f LD0.SPEMMXU2.VAr.phsA.cVal .mag.f LD0.SPEMMXU2.VAr.phsB.cVal .mag.f LD0.SPEMMXU2.VAr.phsC.cVal .mag.f LD0.SPEMMXU2.VA.phsA.cVal. mag.f LD0.SPEMMXU2.VA.phsB.cVal. mag.f LD0.SPEMMXU2.VA.phsC.cVal. mag.f LD0.SPEMMXU2.PF.phsA.cVal. mag.f LD0.SPEMMXU2.PF.phsB.cVal. mag.f LD0.SPEMMXU2.PF.phsC.cVal. mag.f

Type s32

100

SP SE (2)Phase B Active Power

100

SP SE (2)Phase C Active Power

100

SP SE (2)Phase A Reactive Power

100

SP SE (2)Phase B Reactive Power

100

SP SE (2)Phase C Reactive Power

100

SP SE (2)Phase A Apparent Power

100

SP SE (2)Phase B Apparent Power

100

SP SE (2)Phase C Apparent Power

100 100 100

0 0 0

SP SE (2)Average A Power Factor SP SE (2)Average B Power Factor SP SE (2)Average C Power Factor

Table 121:
Coil Addr Register(:Bit) Addr 674 675 682 683 684 685 774 Dc 6 6 6 6 6 6 6 s16 s32 s32 MCD

P-E (1):Three-phase power and energy measurement - instance 1 (PEMMXU1)


Scale 100 100 100 100 Offset 0 0 0 0 Description P E (1) Total Active Power P E (1) Total Reactive Power P E (1) Total Apparent Power P E (1) Average Power Factor IEC61850 Data Attribute Name LD0.PEMMXU1.TotW.instMag.f LD0.PEMMXU1.TotVAr.instMag.f LD0.PEMMXU1.TotVA.instMag.f LD0.PEMMXU1.TotPF.instMag.f

Type s32

RET615 ANSI Point List Manual

49

Section 2 Modbus data mappings

1MAC207644-MB B

Table 122:
Coil Addr Register(:Bit) Addr 692 693 700 701 702 703 783 Dc 6 6 6 6 6 6 6 s16 s32 s32 MCD

P-E (2):Three-phase power and energy measurement - instance 2 (PEMMXU2)


Scale 100 100 100 100 Offset 0 0 0 0 Description P E (2) Total Active Power P E (2) Total Reactive Power P E (2) Total Apparent Power P E (2) Average Power Factor IEC61850 Data Attribute Name LD0.PEMMXU2.TotW.instMag.f LD0.PEMMXU2.TotVAr.instMag.f LD0.PEMMXU2.TotVA.instMag.f LD0.PEMMXU2.TotPF.instMag.f

Type s32

Table 123:
Coil Addr Register(:Bit) Addr 786 Dc 6 MCD

f:Frequency measurement - instance 1 (FMMXU1))


Scale 100 Offset 0 Description Frequency IEC61850 Data Attribute Name LD0.FMMXU1.Hz.instMag.f

Type u16

Table 124:
Coil Addr 2942 2943 Register(:Bit) Addr 2202:2 2202:3 Dc 0 0 Yes MCD

TP - 1:Minimum pulse timer (2 pcs) - instance 1 (TPGAPC1)


Scale Offset Description TP - 1 In2/Out2 IEC61850 Data Attribute Name LD0.TPGAPC1.Op.general

Type

Table 125:
Coil Addr 2944 2945 Register(:Bit) Addr 2202:4 2202:5 Dc 0 0 Yes MCD

TP - 2:Minimum pulse timer (2 pcs) - instance 2 (TPGAPC2)


Scale Offset Description TP - 2 In2/Out2 IEC61850 Data Attribute Name LD0.TPGAPC2.Op.general

Type

Table 126:
Coil Addr 2946 2947 Register(:Bit) Addr 2202:6 2202:7 Dc 0 0 Yes MCD

TP - 3:Minimum pulse timer (2 pcs) - instance 3 (TPGAPC3)


Scale Offset Description TP - 3 In2/Out2 IEC61850 Data Attribute Name LD0.TPGAPC3.Op.general

Type

Table 127:
Coil Addr 2948 2949 Register(:Bit) Addr 2202:8 2202:9 Dc 0 0 Yes MCD

TP - 4:Minimum pulse timer (2 pcs) - instance 4 (TPGAPC4)


Scale Offset Description TP - 4 In2/Out2 IEC61850 Data Attribute Name LD0.TPGAPC4.Op.general

Type

50

RET615 ANSI Point List Manual

1MAC207644-MB B

Section 2 Modbus data mappings

Table 128:
Coil Addr 5458 5459 Register(:Bit) Addr 2502:0 2502:1 241 2108 Dc 0 0 0 0 Yes MCD

DFR:Disturbance recorder (RDRE1)


Scale Offset Description DFR Disturbance Recording Made IEC61850 Data Attribute Name DR.RDRE1.RcdMade.stVal DR.RDRE1.MemUsed.stVal DR.RDRE1.FltNum.stVal

Type

u16 u16

1 1

0 0

DFR Recording Memory Used % DFR Number Of Recordings

Table 129:
Coil Addr 2932 2933 Register(:Bit) Addr 2201:8 2201:9 862 Dc 0 0 6 Yes MCD

FLO:Fault location (DRFLO1)


Scale Offset Description FLO Relay Trip IEC61850 Data Attribute Name LD0.DRFLO1.Tr.general LD0.DRFLO1.FltDisKm.mag.f

Type

u16

100

FLO Distance to fault measured in Km/Miles

Table 130:
Control Structure Control Register Addr Control bit number

"Table - Control Structures


Description IEC61850 Data Attribute Name

2513 2514 2515 2516 2516 2516 2516 2516 2516 2516 2516 2516 2516 2516 2516 2516 2516 2516 2516 2517 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Control Structure 1 Execute Register Control Structure 1 Password 1 Control Structure 1 Password 2 Turn Off Trip LEDs Turn Off Alarm Indication LEDs 52(1) Select Open Breaker 1 52(1) Select Close Breaker 1 52(1) Cancel Select Breaker 1 52(1) Operate Select Breaker 1 52(1) Direct Open Breaker 1 52(1) Direct Close Breaker 1 52(2) Select Open Breaker 2 52(2) Select Close Breaker 2 52(2) Cancel Select Breaker 2 52(2) Operate Select Breaker 2 52(2) Direct Open Breaker 2 52(2) Direct Close Breaker 2 Clear Power Quality Data Reserved Control Structure 1 Confirmation Register Control Structure 2 Execute Register Control Structure 2 Password 1 LD0.LLN0.LEDRs1.Oper.ctlVal LD0.LLN0.LEDRs2.Oper.ctlVal CTRL.CBCSWI1.Pos.Oper.ctlVal CTRL.CBCSWI1.Pos.Oper.ctlVal CTRL.CBCSWI1.Pos.Oper.ctlVal CTRL.CBCSWI1.Pos.Oper.ctlVal CTRL.CBCSWI1.Pos.Oper.ctlVal CTRL.CBCSWI1.Pos.Oper.ctlVal CTRL.CBCSWI2.Pos.Oper.ctlVal CTRL.CBCSWI2.Pos.Oper.ctlVal CTRL.CBCSWI2.Pos.Oper.ctlVal CTRL.CBCSWI2.Pos.Oper.ctlVal CTRL.CBCSWI2.Pos.Oper.ctlVal CTRL.CBCSWI2.Pos.Oper.ctlVal LD0.LLN0.PQRs.Oper.ctlVal

2518 2519

RET615 ANSI Point List Manual

51

Section 2 Modbus data mappings

1MAC207644-MB B

Control Structure

Control Register Addr 2520 2521 2521 2521 2521 2521 2521 2521 2521 2521 2521 2521 2521 2521 2521 2521 2521 2522

Control bit number

Description Control Structure 2 Password 2

IEC61850 Data Attribute Name

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

FLO Reset Fault Record Counter DFR Trigger Disturbance Recording DFR Clear Disturbance Records Reserved Reserved Clear Current Demand Metering Source 1 52CM(1) Reset Breaker Accumulated Power 52CM(1) Reset Breaker remaining life 86/94-1 Clear Lockout Master Trip1 86/94-1 Clear Master Trip1 86/94-2 Clear Lockout Master Trip2 86/94-2 Clear Master Trip2 Reserved Reserved 49T(1)Clear Temperature measurement Reserved Control Structure 2 Confirmation Register Control Structure 3 Execute Register Control Structure 3 Password 1 Control Structure 3 Password 2

LD0.FLTMSTA1.RecRs.Oper.ctlVal DR.RDRE1.RcdTrg.Oper.ctlVal DR.RDRE1.MemClr.Oper.ctlVal

LD0.CMSTA1.RecRs.Oper.ctlVal LD0.SSCBR1.RsAccAPwr.Oper.ctlVal LD0.SSCBR1.RsCBWear.Oper.ctlVal LD0.TRPPTRC1.LORs.Oper.ctlVal LD0.TRPPTRC1.TrRs.Oper.ctlVal LD0.TRPPTRC2.LORs.Oper.ctlVal LD0.TRPPTRC2.TrRs.Oper.ctlVal

LD0.T1PTTR2.RsTmp.Oper.ctlVal

2523 2524 2525 2526 2526 2526 2526 2526 2526 2526 2526 2526 2526 2526 2526 2526 2526 2526 2526 2527 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

52CM(1) Reset Breaker Tavel Time 52CM(1) Reset Breaker Spring Charging time P E(1) Reset Three Phase Power Meter Reset Device Reserved Reserved Clear Current Demand Metering Source 1 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Control Structure 3 Confirmation Register

LD0.SSCBR1.RsTrvTm.Oper.ctlVal LD0.SSCBR1.RsSprChaTm.Oper.ctlVal LD0.PEMMTR1.SupDmdRs.Oper.ctlVal LD0.LPHD1.RsDev.Oper.ctlVal

LD0.CMSTA2.RecRs.Oper.ctlVal

52

RET615 ANSI Point List Manual

1MAC207644-MB B

Section 2 Modbus data mappings

Control Structure

Control Register Addr

Control bit number

Description

IEC61850 Data Attribute Name

2528 2529 2530 2531 2531 2531 2531 2531 2531 2531 2531 2532 8 9 10 11 12 13 14 15

Control Structure 4 Execute Register Control Structure 4 Password 1 Control Structure 4 Password 2 P E(2) Reset Three Phase Power Meter SP SE(1) Reset Three Phase Power Meter P E(2) Reset Three Phase Power Meter 52CM(2) Reset Breaker Accumulated Power 52CM(2) Reset Breaker remaining life 52CM(2) Reset Breaker Tavel Time 52CM(2) Reset Breaker Spring Charging time Reserved Control Structure 4 Confirmation Register Control Structure 8 Execute Register Control Structure 8 Password 1 Control Structure 8 Password 2 8 9 10 11 12 Reserved Reserved Reserved Reserved Reserved Control Structure 8 Confirmation Register LD0.PEMMTR2.SupDmdRs.Oper.ctlVal LD0.SPEMMTR1.SupDmdRs.Oper.ctlV al LD0.SPEMMTR2.SupDmdRs.Oper.ctlV al LD0.SSCBR2.RsAccAPwr.Oper.ctlVal LD0.SSCBR2.RsCBWear.Oper.ctlVal LD0.SSCBR2.RsTrvTm.Oper.ctlVal LD0.SSCBR2.RsSprChaTm.Oper.ctlVal

2548 2549 2550 2551 2551 2551 2551 2551 2552

RET615 ANSI Point List Manual

53

Section 2 Modbus data mappings

1MAC207644-MB B

54

RET615 ANSI Point List Manual

1MAC207644-MB B

Section 3 Glossary

Section 3

Glossary

AFL ANSI AR CB CT CTRL DFR DNP3

Application function block library American National Standards Institute Autoreclosing Circuit breaker Current transformer Control logical device Digital fault recorder A distributed network protocol originally developed by Westronic. The DNP3 Users Group has the ownership of the protocol and assumes responsibility for its evolution. Disturbance recorder Electromagnetic compatibility Human-machine interface Input/output Identifier or identification International standard for substation communication and modelling Intelligent electronic device Logical device zero (0) Light-emitting diode Local human-machine interface Logical node zero (0) Momentary change detect A serial communication protocol developed by the Modicon company in 1979. Originally used for communication in PLCs and RTU devices. Momentary position Protection and Control IED Manager Programmable logic controller Select-before-operate

DR EMC HMI I/O ID IEC 61850 IED LD0 LED LHMI LLN0 MCD Modbus

MOM PCM600 PLC SBO

RET615 ANSI Point List Manual

55

Section 3 Glossary

1MAC207644-MB B

stVal SW UTC Val

Status value Software Coordinated universal time Value

56

RET615 ANSI Point List Manual

Contact us

1MAC270644-MB B Copyright 2011 ABB. All rights reserved.

ABB Inc. Distribution Automation 4300 Coral Ridge Drive Coral Springs, FL 33065, USA Phone:+1 (800) 523-2620 Phone:+1 954-752-6700 Fax:+1 954 345-5329 www.abb.com/substationautomation

Vous aimerez peut-être aussi