Académique Documents
Professionnel Documents
Culture Documents
Close Window
Assessment System
Exam Viewer - DRSEnt Final - CCNA Discovery: Introducing Routing and Switching in the Enterprise (Version
4.0)
Below you will find the assessment items as presented on the exam as well as the scoring rules associated with the item.
Use of the exam information in the Exam Viewer is subject to the terms of the Academy Connection Website Usage Agreement between you
and Cisco. The purpose of the Exam Viewer is to support instruction while not compromising exam security for other Cisco Networking
Academies or students. This material should not be distributed outside a proctored and controlled setting. If misuse is found, action will be
taken to limit access to assessment content. Please remember to logout and close your browser window after using the Exam Viewer.
31
Refer to the exhibit. Which route will be added to the routing table of R1 as a result of running the commands displayed?
D 192.168.0.0/24 is a summary, Null0
D 192.168.0.0/22 is a summary, Null0
D 192.168.0.0/24 [90/203010] via 10.1.1.2, 00:00:10, Serial0/0/0
D 192.168.0.0/22 [90/203010] via 10.1.1.2, 00:00:10, Serial0/0/0
Max Value = 2
Max Value = 2
Max Value = 3
Refer to the exhibit. Switch1 and Switch2 are connected to each other via a trunk link that has been tested and is working properly. Why
is VTP unable to propagate VLANs from one switch to the other?
The revision number is different on both switches.
Both switches are in server mode.
The VTP domain name is different on both switches.
The VTP pruning mode is disabled.
Max Value = 2
Max Value = 2
Max Value = 2
Max Value = 2
Refer to the exhibit. OSPF is enabled and the network is fully converged. Which two routers will be designated as the DR and BDR, if all
the routers are booted at the same time? (Choose two.)
R1 will be the DR.
R4 will be the DR.
R5 will be the DR.
R2 will be the BDR.
R3 will be the BDR.
R4 will be the BDR.
Max Value = 2
Max Value = 2
Refer to the exhibit. Which Telnet session will be blocked as a result of the displayed commands?
the session from host A to host B
the session from host B to hosts C and D
the session from host B to hosts E and F
the session from host E and host F to host A and host B
Max Value = 2
Refer to the exhibit. What information can be determined from the exhibited command?
The command specifies how traffic will be routed to the 10.1.1.2 host.
It will set the default route in the routing table.
This route has an administrative distance of 1.
If a dynamic routing protocol with default parameters is configured on this router, this route will not be installed in the routing table.
Max Value = 2
Refer to the exhibit. What is the result of configuring the newly installed R1 with the exhibited command?
It will set the gateway of last resort for R1.
It will configure the IP address 10.1.1.2 on one interface of R1.
It configures the router to forward traffic that is destined for the 192.168.1.128/26 network through the interface with IP address
10.1.1.2.
It configures a static route for all packets with the source network address 192.168.1.128/26.
Max Value = 2
Max Value = 2
Refer to the exhibit. All switches are configured with default bridge priority. Which two ports will be STP root ports if all links are
operating at the same bandwidth? (Choose two.)
Fa0/1 interface of switch A
Fa0/2 interface of switch A
Fa0/1 interface of switch B
Fa0/2 interface of switch B
Fa0/1 interface of switch C
Fa0/2 interface of switch C
Max Value = 2
Max Value = 2
Max Value = 3
Refer to the exhibit. Which VTP function will this switch perform?
It will create, change, and delete VLANs.
It will send VTP messages to other attached switches.
It will ignore information that is contained in the VTP message.
It will retain its original database when it receives updates from the server.
Max Value = 2
Max Value = 2
Refer to the exhibit. What is the purpose of assigning the IP address 192.168.30.1 to an access layer switch?
to assign a default gateway to the hosts that are connected to the switch
to allow hosts on the same LAN to connect to each other
to allow remote management of the switch
to allow inter-VLAN communication
Max Value = 2
Max Value = 2
Refer to the exhibit. The network administrator has implemented NAT on R1. Which two addresses are valid inside global addresses?
(Choose two.)
192.168.1.1
192.168.1.2
198.133.219.1
198.133.219.102
198.133.219.103
Max Value = 2
Max Value = 2
Refer to the exhibit. What is the correct description of the highlighted address?
It is the address of the destination network.
It is the routerID of the neighboring router.
It is the next hop address of the feasible successor.
It is the IP address of the serial0/0/0 interface of RouterC.
Max Value = 2
Refer to the exhibit. R1 is using the default OSPF operation. Which IP address will be used as the router ID of R1?
192.168.201.1
172.16.1.1
10.10.10.1
10.1.1.1
Max Value = 2
Max Value = 2
Refer to the exhibit. None of the hosts in network A are able to access the Internet. How can this problem be resolved?
Configure dynamic NAT instead of PAT.
Configure the access list for the correct network.
Include the ip nat pool command in the configuration.
Configure the ip nat inside command on the correct interface.
Max Value = 2
Max Value = 2
Reset View
Close Window
All contents copyright ©2001-2008 Cisco Systems, Inc. All rights reserved. Privacy Statement and Trademarks.