Vous êtes sur la page 1sur 4

CASE

CASES OF ASME BOILER AND PRESSURE VESSEL CODE

2146

Approval Date: November 25, 1992 Code Cases will remain available for use until annulled by the applicable Standards Committee.

Case 2146 24Cr-17Ni-6Mn-4.5Mo-N, UNS S34565, Austenitic Stainless Steel Forgings, Bar, Fittings, Welded and Seamless Pipe and Tube, Plate, Sheet, and Strip Section VIII, Division 1 Inquiry: May solution annealed austenitic stainless steel, 24Cr-17Ni-6Mn-4.5Mo-N, UNS S34565, forgings, bar, ttings, welded and seamless pipe and tube, plate, sheet and strip, meeting the chemical and mechanical property requirements given in Tables 1 and 2, and otherwise conforming to the requirements of specications of SA-182, SA-213, SA-240, SA-249, SA-312, SA-376, SA-403, SA-409, and SA-479, as applicable, be used in welded construction under the rules of Section VIII, Division 1? Reply: It is the opinion of the Committee that the material listed in the Inquiry may be used in welded construction
TABLE 1 CHEMICAL REQUIREMENTS
Element Carbon, max. Manganese Phosphorus, max. Sulfur, max. Silicon, max. Nickel Chromium Molybdenum Nitrogen Columbium, max. Weight, % 0.03 5.07.0 0.030 0.010 1.0 16.018.0 23.025.0 4.05.0 0.40.6 0.1

under the rules of Section VIII, Division 1, provided the following additional requirements are met. (a) The material shall be furnished in the solution annealed condition consisting of holding at a temperature in the range from 2050F to 2140F for a time ranging from 1530 minutes, followed by water quenching, or rapid cooling by other means. (b) The rules for austenitic stainless steels given in Part UHA shall apply. (c) The maximum allowable design stress values shall be those listed in Table 3. (d) For external pressure design, use Fig. 1, the tabular values are listed in Table 4. (e) Separate welding procedure and performance qualications shall be conducted for the material in accordance with Section IX. (f) Postweld heat treatment after forming or fabrication is neither required nor prohibited, but when heat treatment is performed, it shall be as in (a) above. (g) This Case number shall be referenced in the documentation of the material and recorded on the Manufacturers Data Report.
TABLE 3 MAXIMUM ALLOWABLE STRESS VALUES, ksi
For Metal Temperature Not Exceeding, F 100 200 300 400 500 600 650 700 750 Forgings, Bar, Plate, Sheet, Strip, Seamless Pipe and Tube, Fittings 28.8 28.4 26.9 25.9 25.3 25.0 24.8 24.6 24.3 Welded Pipe and Tube, Welded Fittings [Note (1)] 24.5 24.1 22.9 22.0 21.5 21.3 21.1 20.9 20.7

TABLE 2 MECHANICAL PROPERTIES REQUIREMENTS


Yield strength, min., 0.2% offset, ksi Tensile strength, min., ksi Elongation in 2 in., min., % 60 115 35

NOTE: (1) A quality factor of 0.85 has been applied in arriving at the allowable stress values for this material.

The Committees function is to establish rules of safety, relating only to pressure integrity, governing the construction of boilers, pressure vessels, transport tanks and nuclear components, and inservice inspection for pressure integrity of nuclear components and transport tanks, and to interpret these rules when questions arise regarding their intent. This Code does not address other safety issues relating to the construction of boilers, pressure vessels, transport tanks and nuclear components, and the inservice inspection of nuclear components and transport tanks. The user of the Code should refer to other pertinent codes, standards, laws, regulations or other relevant documents.

1 (2146)
Copyright ASME International Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS Licensee=Larsen and Toubro Ltd Baroda/5954522003, User=Dhanaraj M, Francis Not for Resale, 07/24/2010 01:26:16 MDT

2146

FIG. 1

CHART FOR DETERMINING SHELL THICKNESS OF CYLINDRICAL AND SPHERICAL VESSELS UNDER EXTERNAL PRESSURE WHEN CONSTRUCTED OF AUSTENITIC STAINLESS STEEL UNS S34565
100,000 80,000 60,000 50,000 40,000 30,000 20,000

CASE (continued)

600F 800F

6000 5000 4000 3000 2000

Factor B
10,000 400F 8000

Copyright ASME International Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS

E = 28.3 106

E = 27.6 106

E = 26.5 106 Up to 100F 200F

CASES OF ASME BOILER AND PRESSURE VESSEL CODE

--```,,,`,`,````,,,``,``,`,`````-`-`,,`,,`,`,,`---

E = 25.3 106

2 (2146)
3 0.001 Factor A 4 5 6 7 8 9 2 3 4 5 6 7 8 9 0.01

E = 24.1 106

1000 2 3 4 5 6 7 8 9 0.1

Licensee=Larsen and Toubro Ltd Baroda/5954522003, User=Dhanaraj M, Francis Not for Resale, 07/24/2010 01:26:16 MDT

0.0001

CASE (continued)
CASES OF ASME BOILER AND PRESSURE VESSEL CODE

2146

TABLE 4 TABULAR VALUES FOR FIG. 1


Up to 100F, E p 28.3 106 psi Temp. 200F, E p 27.6 106 psi Temp. 400F, E p 26.5 106 psi Temp. 600F, E p 25.3 106 psi Temp. 800F, E p 24.1 106 psi

A
1.00 04 1.25 03 2.24 03 4.01 03 9.49 03 4.29 02 7.50 02 ...

B, psi
1,416 17,715 21,848 26,572 28,344 29,997 31,107 ...

A
1.00 1.11 2.76 6.14 1.64 5.63 5.72 7.50 04 03 03 03 02 02 02 02

B, psi
1,382 15,324 19,702 21,891 22,985 23,697 24,080 24,463

A
1.00 04 1.08 03 3.23 03 6.78 03 1.80 02 7.47 02 ... ...

B, psi
1,327 14,340 16,464 18,057 19,651 20,819 ... ...

A
1.00 04 9.79 04 3.77 03 8.38 03 2.41 02 7.50 02 ... ...

B, psi
1,267 12,400 15,781 17,885 19,201 20,163 ... ...

A
1.00 8.84 2.28 5.90 1.21 2.19 5.55 7.50 04 04 03 03 03 02 02 02

B, psi
1,207 10,673 13,723 16,773 17,789 18,450 19,314 19,713

Copyright ASME International Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS

--```,,,`,`,````,,,``,``,`,`````-`-`,,`,,`,`,,`---

3 (2146)
Licensee=Larsen and Toubro Ltd Baroda/5954522003, User=Dhanaraj M, Francis Not for Resale, 07/24/2010 01:26:16 MDT

INTENTIONALLY LEFT BLANK

--```,,,`,`,````,,,``,``,`,`````-`-`,,`,,`,`,,`---

Copyright ASME International Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS

Licensee=Larsen and Toubro Ltd Baroda/5954522003, User=Dhanaraj M, Francis Not for Resale, 07/24/2010 01:26:16 MDT

Vous aimerez peut-être aussi