Académique Documents
Professionnel Documents
Culture Documents
After completion of modelling the geometries of the heat sinks, a quantitative study is carried out; and it follows as: Material describing Boundary conditions defining Meshing Solving and Post processing.
Material describing: For both the heat sinks, the working conditions and material properties and domain properties are similar. And they are as follows:
Material parameters
Name Dynamic viscosity Ratio of specific heats Heat capacity at constant pressure Density Thermal conductivity Value eta(T[1/K])[Pa*s] 1.4 Cp(T[1/K])[J/(kg*K)] rho(pA[1/Pa], T[1/K])[kg/m^3] k(T[1/K])[W/(m*K)] Unit Pa*s 1 J/(kg*K) kg/m^3 W/(m*K)
SELECTION
Geometric entity level Selection Domain Domains 211
Equations
Thermal Insulation 1
SELECTION
Geometric entity level Selection Boundary Boundaries 25, 8
Equations
Wall 1
Wall 1
SELECTION
Geometric entity level Selection Boundary Boundaries 27, 912, 1416, 1820, 2236, 3840, 4244, 4660, 6264, 6668, 7083
Equations
Initial Values 1
Initial Values 1
SELECTION
Geometric entity level Domain Selection Domains 111
Fluid 1
Fluid 1
SELECTION
Geometric entity level Selection Domain Domain 1
Equations
Material
Air Air Air
Property group
Basic Basic Basic
Air
Basic
Air
Basic
Heat Source 1
Heat Source 1
SELECTION
Geometric entity level Domain Selection Domain 2
Equations
SETTINGS
Description Heat source Total power Value Total power 1
Inlet 1
Inlet 1
SELECTION
Geometric entity level Selection Boundary Boundary 84
Equations
SETTINGS Description Boundary condition Average velocity Value Laminar inflow 5[cm/s]
Outlet 1
Outlet 1
SELECTION
Geometric entity level Boundary Selection Boundary 1
Equations
Temperature 1
Temperature 1
SELECTION
Geometric entity level Boundary Selection Boundary 84
Equations
SETTINGS
Description Temperature Value 20[degC]
Outflow 1
Outflow 1
SELECTION
Geometric entity level Boundary Selection Boundary 1
Equations
MESH 1
Mesh 1
Value Study 1
Stationary
Defined by study step Stationary INITIAL VALUES OF VARIABLES SOLVED FOR Name Solution Value Zero
VALUES OF VARIABLES NOT SOLVED FOR Name Solution Mod1.u (Mod1_u) GENERAL Name Value Value Zero
Field components {mod1.u, mod1.v, mod1.w} Mod1.T (Mod1_T) GENERAL Name Value
Defined by study step Stationary Fully Coupled 1 (Fc1) GENERAL Name Value
Nonlinear method Constant (Newton) Damping factor Iterative 1 (I1) ERROR Name Factor in error estimate Value 20 0.8
Relaxation factor 0.6 Postsmoother (Po) Vanka 1 (Va1) MAIN Name Value
Coarse Solver (Cs) Direct 1 (D1) GENERAL Name Value Solver PARDISO
Results
DATA SETS Solution 1 SELECTION Geometric entity level Domain Selection SOLUTION Name Solution Model Surface 1 SELECTION Geometric entity Boundary level Selection Boundaries 27, 912, 1416, 1820, 2236, 3840, 4244, 4660, 6264, 6668, 7083 Value Solver 1 Save Point Geometry 1 Geometry geom1
Coordinate Systems
Boundary System 1
Coordinate system type Identifier Boundary system sys1
Geometry 1
Geometry 1
Materials Air
Aluminum 3003-H18
Aluminum 3003-H18
Selection
Geometric entity level Selection Domain Domains 211
Features
Heat Transfer in Solids 1 Thermal Insulation 1 Wall 1 Initial Values 1 Fluid 1 Heat Source 1 Inlet 1 Temperature 1 Outlet 1 Outflow 1
Mesh 1
Mesh 1 STUDY
Stationary
Mesh selection
Geometry Mesh Geometry 1 (geom1) mesh1
Physics selection
Physics Discretization Conjugate Heat Transfer (nitf) physics
RESULTS
Data Sets
Solution 1
Selection
Geometric entity level Domain Selection Geometry geom1
Solution
Name Value Solution Solver 1 Model Save Point Geometry 1
Surface 1
Selection
Geometric entity level Selection Boundary Boundaries 27, 912, 1417, 1922, 2430, 3235, 3740, 4248, 5053, 5558, 6065
Data
Name Value Data set Solution 1