Académique Documents
Professionnel Documents
Culture Documents
SECTION
BCS
CONTENTS
BASIC INSPECTION ................................ .... 3
INSPECTION AND ADJUSTMENT ................ ..... 3
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT .................................................... ...... 3 ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description ............................ ...... 3 ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement ...... 3 REAR WINDOW DEFOGGER : CONSULT-III Function (BCM - REAR DEFOGGER) ................. ....17 BUZZER ................................................................. ....17 BUZZER : CONSULT-III Function (BCM - BUZZER) ...................................................................... ....17 INT LAMP ............................................................... ....17 INT LAMP : CONSULT-III Function (BCM - INT LAMP) .................................................................. ....18 HEADLAMP ........................................................... ....19 HEADLAMP : CONSULT-III Function (BCM HEAD LAMP) ....................................................... ....19 WIPER .................................................................... ....21 WIPER : CONSULT-III Function (BCM - WIPER)....21 FLASHER ............................................................... ....22 FLASHER : CONSULT-III Function (BCM FLASHER) ........................................................... ....22 INTELLIGENT KEY ................................................ ....23 INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY) ................................ ....23 COMB SW .............................................................. ....26 COMB SW : CONSULT-III Function (BCM COMB SW) .......................................................... ....26 BCM ....................................................................... ....27 BCM : CONSULT-III Function (BCM - BCM) ....... ....27 IMMU ...................................................................... ....27 IMMU : CONSULT-III Function (BCM - IMMU) .... ....27 BATTERY SAVER ................................................. ....28 BATTERY SAVER : CONSULT-III Function (BCM - BATTERY SAVER) ........................................... ....28 TRUNK ................................................................... ....29 TRUNK : CONSULT-III Function (BCM - TRUNK) ....29 THEFT ALM ........................................................... ....29
BCS
BCS-1
THEFT ALM : CONSULT-III Function (BCM THEFT) ................................................................ ... 29 RETAIND PWR ...................................................... ... 30 RETAIND PWR : CONSULT-III Function (BCM RETAINED PWR) ................................................ ... 30 SIGNAL BUFFER ................................................... ... 31 SIGNAL BUFFER : CONSULT-III Function (BCM - SIGNAL BUFFER) ............................................. ... 31 AIR PRESSURE MONITOR ................................... ... 31 AIR PRESSURE MONITOR : CONSULT-III Function (BCM - AIR PRESSURE MONITOR) ............ ... 31
PRECAUTION ............................................ 77
PRECAUTIONS .............................................. ... 77
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" .............................................................. ... 77 Precaution for Battery Service ............................. ... 77
BCS-2
BASIC INSPECTION
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description
INFOID:0000000005656175
Perform the system initialization when replacing BCM, replacing Intelligent Key or registering an additional Intelligent Key.
INFOID:0000000005656176
BCS
BCS-3
SYSTEM DESCRIPTION
BODY CONTROL SYSTEM
System Description
OUTLINE
BCM (Body Control Module) controls the various electrical components. It inputs the information required to the control from CAN communication and the signal received from each switch and sensor. BCM has combination switch reading function for reading the operation status of combination switches (light, turn signal, wiper and washer) in addition to a function for controlling the operation of various electrical components. It also has the signal transmission function as the passed point of signal and the power saving control function that reduces the power consumption with the ignition switch OFF. BCM is equipped with the diagnosis function that performs the diagnosis with CONSULT-III and various settings.
INFOID:0000000005656177
Warning chime system Door lock system Trunk open system Infiniti Vehicle Immobilizer System (IVIS) - NATS Vehicle security system Panic alarm Automatic drive positioner system Rear window defogger system
BCS-4
B
DLK-15, "INTELLIGENT KEY SYSTEM : System Diagram"
E
INFOID:0000000005656178
J
JPMIA0506ZZ
1. A.
BCS
BCS-5
JMMIA0333GB
NOTE: *1: TAIL LAMP switch links lighting switch 1ST position. *2: FR WIP INT/AT is FR WIPER INT/AUTO.
System Description
OUTLINE
INFOID:0000000005656180
BCM reads the status of the combination switch (light, turn signal, wiper and washer) and recognizes the status of each switch. BCM is a combination of 5 output terminals (OUTPUT 1 - 5) and 5 input terminals (INPUT 1 - 5). It reads a maximum of 20 switch status.
JMMIA0337GB
NOTE: *1: TAIL LAMP switch links lighting switch 1ST position. *2: FR WIP INT/AT is FR WIPER INT/AUTO.
BCS-6
JPMIA0067GB
NOTE: BCM reads the status of the combination switch at 60 ms interval when BCM is controlled at low power consumption mode. BCM operates as follows and judges the status of the combination switch. INPUT 1 - 5 outputs the voltage waveforms of 5 systems simultaneously. It operates the transistor on OUTPUT side in the following order: OUTPUT 5 4 3 2 1. The voltage waveform of INPUT corresponding to the formed circuit changes according to the operation of the transistor on OUTPUT side if any (1 or more) switches are ON. It reads this change of the voltage as the status signal of the combination switch.
BCS
JPMIA0068GB
BCS-7
The circuit between INPUT 1 and OUTPUT 5 is formed when the TURN RH switch is turned ON.
JMMIA0338GB
BCM detects the combination switch status signal 1E when the signal of OUTPUT 5 is input to INPUT 1. BCM judges that the TURN RH switch is ON when the signal 1E is detected.
Example 2: When some switches (turn RH switch, front wiper LO switch) are turned ON
The circuits between INPUT 1 and OUTPUT 5 and between INPUT 1 and OUTPUT 3 are formed when the TURN RH switch and FR WIPER LOW switch are turned ON.
JMMIA0339GB
BCM detects the combination switch status signal 1CE when the signals of OUTPUT 3 and OUTPUT 5 are input to INPUT 1. BCM judges that the TURN RH switch and FR WIPER LOW switch are ON when the signal 1CE is detected.
BCS-8
BCS
BCS-9
JPMIA1239GB
System Description
OUTLINE
INFOID:0000000005656183
BCM has the signal transmission function that outputs/transmits each input/received signal to each unit.
Combination meter (through unified meter and A/C amp.) (CAN) IPDM E/R (CAN) Driver seat control unit (CAN) Combination meter (through unified meter and A/C amp.) (CAN) Combination meter (through unified meter and A/C amp.) (CAN)
TCM (CAN)
BCS-10
JPMIA0069GB
System Description
OUTLINE
INFOID:0000000005656185
BCM incorporates a power saving control function that reduces the power consumption according to the vehicle status. BCM switches the status (control mode) by itself with the power saving control function. It performs the sleep request to each unit [IPDM E/R, combination meter (unified meter and A/C amp.) and driver seat control unit] that operates with the ignition switch OFF.
Normal mode (wake-up)
- CAN communication is normally performed with other units - Each control with BCM is operating properly
CAN communication sleep mode (CAN sleep)
BCS-11
CAN sleep condition Receiving the sleep-ready signal (ready) from all units Ignition switch: OFF Vehicle security system and panic alarm: Not operation Warning chime: Not operation Intelligent Key system buzzer: Not operation Trunk room lamp switch status: No change Stop lamp switch: OFF ICC brake hold relay (with ICC): OFF Key slot (card switch) status: No change Turn signal indicator lamp: Not operation Exterior lamp: OFF Door lock status: No change CONSULT-III communication status: Not communication Meter display signal: Non-transmission Door switch status: No change Rear window defogger: OFF
Interior room lamp battery saver: Time out Power window switch communication: No transmission Push-button ignition switch illumination: OFF Infiniti Vehicle Immobilizer System (IVIS) - NATS: Not operation Remote keyless entry receiver communication status: No communication Tire pressure monitor system (TPMS) - AIR PRESSURE MONITOR: Stop LOCK indicator lamp: OFF ACC indicator lamp: OFF ON indicator lamp: OFF
Wake-up operation
BCM changes from the low power consumption mode to the CAN communication sleep mode when the any of the BCM wake-up conditions is fulfilled. Only the control with BCM is activated. BCM transmits the sleep wake up signal (wake up) to each unit when any of the CAN wake-up conditions is fulfilled. It changes from the low power consumption mode or the CAN communication sleep mode to the normal mode. Each unit starts the transmission of CAN communication with the sleep wake up signal. In addition, the unified meter and A/C amp. transmits the wake up signal to BCM via CAN communication to report the CAN communication start.
Wake-up condition
CAN wake-up condition Receiving the sleep-ready signal (Not-ready) from any units Key slot (key switch): OFF ON, ON OFF Push-button ignition switch (push switch): OFF ON Hazard switch: OFF ON PASSING switch: OFF ON, ON OFF TAIL LAMP switch: OFF ON Driver door switch: OFF ON, ON OFF Passenger door switch: OFF ON, ON OFF Trunk room lamp switch: OFF ON, ON OFF Driver door request switch: OFF ON Passenger door request switch: OFF ON Trunk lid opener request switch: OFF ON Stop lamp switch: ON ICC brake hold relay (with ICC): ON Clutch interlock switch: OFF ON
Trunk lid opener switch: OFF ON Power window switch communication: Receiving Remote keyless entry receiver communication: Receiving
BCS-12
INFOID:0000000005656186
JPMIA0623ZZ
BCS
1. 4. A. D.
BCM Driver seat control unit Dash side lower (passenger side) Backside of the seat cushion (driver seat)
2. B.
3. C.
N
Behind Cluster lid C
BCS-13
SYSTEM APPLICATION
BCM can perform the following functions for each system. NOTE: It can perform the diagnosis modes except the following for all sub system selection items.
: Applicable item
System Door lock Rear window defogger Warning chime Interior room lamp timer Exterior lamp Wiper and washer Turn signal and hazard warning lamps Intelligent Key system Engine start system Combination switch Body control system IVIS - NATS Interior room lamp battery saver Trunk lid open Vehicle security system RAP system Signal buffer system TPMS NOTE: *: This item is displayed, but is not used.
Sub system selection item DOOR LOCK REAR DEFOGGER BUZZER INT LAMP HEAD LAMP WIPER FLASHER AIR CONDITONER* INTELLIGENT KEY COMB SW BCM IMMU BATTERY SAVER TRUNK THEFT ALM RETAINED PWR SIGNAL BUFFER AIR PRESSURE MONITOR
BCS-14
IGN Counter
0 - 39
BCS
DOOR LOCK
DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)
BCM CONSULT-III FUNCTION
CONSULT-III performs the following functions via CAN communication with BCM.
Diagnosis mode WORK SUPPORT DATA MONITOR ACTIVE TEST Function Description Changes the setting for each system function. The BCM input/output signals are displayed. The signals used to activate each device are forcibly supplied from BCM.
INFOID:0000000005890802
WORK SUPPORT
Revision: 2009 November
BCS-15
*: P range interlock door lock can be selected for M/T models, but automatic door lock/unlock function does not operate.
DATA MONITOR
Monitor Item REQ SW-DR REQ SW-AS REQ SW-BD/TR DOOR SW-DR DOOR SW-AS DOOR SW-RR DOOR SW-RL DOOR SW-BK CDL LOCK SW CDL UNLOCK SW KEY CYL LK-SW KEY CYL UN-SW Contents Indicated [ON/OFF] condition of door request switch (driver side). Indicated [ON/OFF] condition of door request switch (passenger side). Indicated [ON/OFF] condition of trunk lid opener request switch. Indicated [ON/OFF] condition of front door switch (driver side). Indicated [ON/OFF] condition of front door switch (passenger side). NOTE: This item is displayed, but cannot be monitored. NOTE: This item is displayed, but cannot be monitored. NOTE: This item is displayed, but cannot be monitored. Indicated [ON/OFF] condition of lock signal from door lock unlock switch. Indicated [ON/OFF] condition of unlock signal from door lock unlock switch. Indicated [ON/OFF] condition of lock signal from door key cylinder. Indicated [ON/OFF] condition of unlock signal from door key cylinder.
ACTIVE TEST
Test item Description This test is able to check door lock/unlock operation. The all door lock actuators are locked when ALL LCK on CONSULT-III screen is touched. The all door lock actuators are unlocked when ALL UNLK on CONSULT-III screen is touched. The door lock actuator (driver side) is unlocked when DR UNLK on CONSULT-III screen is touched. The door lock actuator (passenger side) is unlocked when AS UNLK on CONSULT- III screen is touched. OTR ULK item is displayed, but cannot be monitored.
DOOR LOCK
BCS-16
Data monitor
B
Monitor Item REAR DEF SW PUSH SW Description This is displayed even when it is not equipped. Indicates [ON/OFF] condition of push switch.
ACTIVE TEST
D
Test Item REAR DEFOGGER Description This test is able to check rear window defogger operation. Rear window defogger operates when ON on CONSULT-III screen is touched.
BUZZER
BUZZER : CONSULT-III Function (BCM - BUZZER)
CONSULT-III APPLICATION ITEMS
G
Test item BUZZER Diagnosis mode Data Monitor Active Test Displays BCM input data in real time. Operation of electrical loads can be checked by sending driving signal to them. Description
INFOID:0000000005890816
DATA MONITOR
I
Display item [Unit] VEH SPEED 1 [Km/h] PUSH SW [On/Off] UNLK SEN-DR [On/Off] KEY SW-SLOT [On/Off] TAIL LAMP SW [On/Off] FR FOG SW [On/Off] DOOR SW-DR [On/Off] Description Value of vehicle speed signal received from ABS actuator and electric unit (control unit) with CAN communication line. Status of push button ignition switch judged by BCM.
K
Status of unlock sensor judged by BCM. Status of key slot judged by BCM. Status of each switch judged by BCM using the combination switch readout function.
BCS
Status of front fog lamp switch judged by BCM. Status of driver side door switch judged by BCM.
ACTIVE TEST
O
Display item [Unit] IGN KEY WARN ALM SEAT BELT WARN TEST ID REGIST WARNING LIGHT WARN ALM RUN FLAT/T WARN BUZZER Description The key warning chime operation can be checked by operating the relevant function (On/Off). The seat belt warning chime operation can be checked by operating the relevant function (On/Off). The ID regist warning chime operation can be checked by operating the relevant function (On/Off). The light warning chime operation can be checked by operating the relevant function (On/Off). The run-flat tire warning chime operation can be checked by operating the relevant function (On/Off).
INT LAMP
Revision: 2009 November
BCS-17
INFOID:0000000005890809
JPLIA0093GB
Setting With the interior room lamp timer function Without the interior room lamp timer function 7.5 sec. 15 sec. 30 sec. 0.5 sec. 1 sec. 2 sec. 3 sec. 0 sec. 0.5 sec. 1 sec. 2 sec. 3 sec. Interior room lamp timer activates with synchronizing all doors. Interior room lamp timer activates with synchronizing the driver door only. Sets the interior room lamp gradual dimming time. Sets the interior room lamp gradual brightening time. Sets the interior room lamp ON time. (Timer operating time)
MODE 2
DATA MONITOR
Monitor item [Unit] REQ SW-DR [On/Off] REQ SW-AS [On/Off] PUSH SW [On/Off] ACC RLY-F/B [On/Off] KEY SW-SLOT [On/Off] Description The switch status input from request switch (driver side) The switch status input from front request switch (passenger side) The switch status input from push-button ignition switch NOTE: The item is indicated, but not monitored. Key switch status input from key slot
BCS-18
ACTIVE TEST
Test item INT LAMP Operation On Off STEP LAMP TEST On Off On Off Description Outputs the interior room lamp control signal to turn map lamp ON (Map lamp switch is in DOOR position). Stops the interior room lamp control signal to turn map lamp OFF. Outputs the step lamp control signal to turn step lamp ON. Stops the step lamp control signal to turn step lamp OFF. Outputs the trunk room lamp control signal to turn the trunk room lamp ON. Stops the trunk room lamp control signal to turn the trunk room lamp OFF.
HEADLAMP
HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP)
WORK SUPPORT
Service item BATTERY SAVER SET Setting item On* Off Setting With the exterior lamp battery saver function Without the exterior lamp battery saver function
INFOID:0000000005890811
BCS
BCS-19
DATA MONITOR
Monitor item [Unit] PUSH SW [On/Off] ENGINE STATE [Stop/Stall/Crank/Run] VEH SPEED 1 [km/h] KEY SW-SLOT [On/Off] TURN SIGNAL R [On/Off] TURN SIGNAL L [On/Off] TAIL LAMP SW [On/Off] HI BEAM SW [On/Off] HEAD LAMP SW1 [On/Off] HEAD LAMP SW2 [On/Off] PASSING SW [On/Off] AUTO LIGHT SW [On/Off] FR FOG SW [On/Off] RR FOG SW [On/Off] DOOR SW-DR [On/Off] DOOR SW-AS [On/Off] NOTE: The item is indicated, but not monitored. The switch status input from driver side door switch The switch status input from passenger side door switch Each switch status that BCM judges from the combination switch reading function Description The switch status input from push-button ignition switch The engine status received from ECM with CAN communication The value of the vehicle speed received from unified meter and A/C amp. with CAN communication Key switch status input from key slot
BCS-20
ACTIVE TEST
Test item TAIL LAMP Operation On Off Hi HEAD LAMP Low Off FR FOG LAMP On Off RR FOG LAMP On Off On Off RH CORNERING LAMP LH Off ILL DIM SIGNAL On Off NOTE: The item is indicated, but cannot be tested. NOTE: The item is indicated, but cannot be tested. Description Transmits the position light request signal to IPDM E/R with CAN communication to turn the tail lamp ON. Stops the position light request signal transmission. Transmits the high beam request signal with CAN communication to turn the headlamp (HI). Transmits the low beam request signal with CAN communication to turn the headlamp (LO). Stops the high & low beam request signal transmission. Transmits the front fog light request signal to IPDM E/R with CAN communication to turn the front fog lamp ON. Stops the front fog light request signal transmission. NOTE: The item is indicated, but cannot be tested. NOTE: The item is indicated, but cannot be tested.
WIPER
WIPER : CONSULT-III Function (BCM - WIPER)
WORK SUPPORT
Service item WIPER SPEED SETTING*
1
BCS
INFOID:0000000005890813
N
Description Linked with vehicle speed (Front wiper intermittent time linked with the vehicle speed and wiper intermittent dial position) Not linked with vehicle speed (Front wiper intermittent time linked with the wiper intermittent dial position)
DATA MONITOR
BCS-21
Status of each switch judged by BCM using the combination switch reading function
ACTIVE TEST
Test item Operation Hi Lo INT Off Description Transmits the front wiper request signal (HI) to IPDM E/R with CAN communication to operate the front wiper HI operation. Transmits the front wiper request signal (LO) to IPDM E/R with CAN communication to operate the front wiper LO operation. Transmits the front wiper request signal (INT) to IPDM E/R with CAN communication to operate the front wiper INT operation. Stops transmitting the front wiper request signal to stop the front wiper operation.
FRONT WIPER
FLASHER
FLASHER : CONSULT-III Function (BCM - FLASHER)
WORK SUPPORT
Service item Setting item Lock Only* HAZARD ANSWER BACK Unlk Only Lock/Unlk Off *: Factory setting With locking only With unlocking only With locking/unlocking Without the function Sets the hazard warning lamp answer back function when the door is lock/unlock with the request switch or the key fob. Setting
INFOID:0000000005890812
DATA MONITOR
Monitor item [Unit] REQ SW-DR [On/Off] REQ SW-AS [On/Off] PUSH SW [On/Off] Description The switch status input from the request switch (driver side) The switch status input from the request switch (passenger side) The switch status input from the push-button ignition switch
BCS-22
Each switch condition that BCM judges from the combination switch reading function
The switch status input from the hazard switch Lock signal status received from the remote keyless entry receiver Unlock signal status received from the remote keyless entry receiver Panic alarm signal status received from the remote keyless entry receiver
ACTIVE TEST
Test item Operation RH FLASHER LH Off Description Outputs the voltage to blink the right side turn signal lamps. Outputs the voltage to blink the left side turn signal lamps. Stops the voltage to turn the turn signal lamps OFF.
INTELLIGENT KEY
INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)
WORK SUPPORT
Monitor item CONFIRM KEY FOB ID Description It can be checked whether Intelligent Key ID code is registered or not in this mode. Auto door lock time can be changed in this mode. MODE 1: 1 minute MODE 2: 5 minutes MODE 3: 30 seconds MODE 4: 2 minutes Door lock/unlock function by door request switch (driver side and passenger side) mode can be changed to operate (ON) or not operate (OFF) in this mode. Engine start function mode can be changed to operate (ON) or not operate (OFF) with this mode. Buzzer reminder function mode by trunk opener request switch can be changed to operate (ON) or not operate (OFF) with this mode. Panic alarm button pressing time on Intelligent Key remote control button can be selected from the following with this mode. MODE 1: 0.5 sec. MODE 2: Non-operation MODE 3: 1.5 sec. Unlock button pressing time on Intelligent Key button can be selected from the following with this mode. MODE 1: 3 sec. MODE 2: Non-operation MODE 3: 5 sec. Trunk button pressing on Intelligent Key button can be selected as per the following in this mode. MODE 1: Press and hold MODE 2: Press twice MODE 3: Press and hold, or press twice
INFOID:0000000005890803
BCS
PW DOWN SET
BCS-23
SELF-DIAG RESULT
Refer to DLK-165, "DTC Index".
DATA MONITOR
Monitor Item REQ SW -DR REQ SW -AS REQ SW -BD/TR PUSH SW IGN RLY2 -F/B ACC RLY-FB CLUTCH SW*1 BRAKE SW 1 BRAKE SW 2 DETE/CANCL SW SFT PN/N SW S/L -LOCK S/L -UNLOCK S/L RELAY -F/B UNLK SEN -DR PUSH SW -IPDM IGN RLY1 -F/B DETE SW -IPDM SFT PN -IPDM SFT P -MET Condition Indicates [ON/OFF] condition of door request switch (driver side). Indicates [ON/OFF] condition of door request switch (passenger side). Indicates [ON/OFF] condition of trunk opener request switch. Indicates [ON/OFF] condition of push-button ignition switch. Indicates [ON/OFF] condition of ignition relay 2. NOTE: This item is displayed, but cannot be monitored. Indicates [ON/OFF] condition of clutch switch. Indicates [ON/OFF]*2 condition of brake switch power supply. Indicates [ON/OFF] condition of brake switch. Indicates [ON/OFF] condition of P position. Indicates [ON/OFF] condition of P or N position. Indicates [ON/OFF] condition of steering lock unit (LOCK). Indicates [ON/OFF] condition of steering lock unit (UNLOCK). Indicates [ON/OFF] condition of steering lock relay. Indicates [ON/OFF] condition of driver door UNLOCK status. Indicates [ON/OFF] condition of push-button ignition switch. Indicates [ON/OFF] condition of ignition relay 1. Indicates [ON/OFF] condition of P position. Indicates [ON/OFF] condition of P or N position. Indicates [ON/OFF] condition of P position.
BCS-24
*1: It is displayed but does not operate on M/T models. *2: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
ACTIVE TEST
Test item BATTERY SAVER PW REMOTO DOWN SET OUTSIDE BUZZER Description This test is able to check interior room lamp operation. The interior room lamp is activated after ON on CONSULT-III screen is touched. This test is able to check power window down operation. The power window down is activated after ON on CONSULT-III screen is touched. This test is able to check Intelligent Key warning buzzer operation. The Intelligent Key warning buzzer is activated after ON on CONSULT-III screen is touched. This test is able to check warning chime in combination meter operation. Take away warning chime sounds when TAKE OUT on CONSULT-III screen is touched. Key warning chime sounds when KEY on CONSULT-III screen is touched. OFF position warning chime sounds when KNOB on CONSULT-III screen is touched. This test is able to check warning lamp operation. KEY Warning lamp illuminates when KEY ON on CONSULT-III screen is touched. KEY Warning lamp blinks when KEY IND on CONSULT-III screen is touched. This test is able to check interior room lamp operation. The interior room lamp is activated after ON on CONSULT-III screen is touched.
BCS
INSIDE BUZZER
INDICATOR
INT LAMP
BCS-25
LCD
LOCK INDICATOR
ACC INDICATOR
COMB SW
COMB SW : CONSULT-III Function (BCM - COMB SW)
DATA MONITOR
Monitor item [UNIT] FR WIPER HI [Off/On] FR WIPER LOW [Off/On] FR WASHER SW [Off/On] FR WIPER INT [Off/On] FR WIPER STOP [Off/On] INT VOLUME [1 - 7] Description Displays the status of the FR WIPER HI switch in combination switch judged by BCM with the combination switch reading function. Displays the status of the FR WIPER LOW switch in combination switch judged by BCM with the combination switch reading function. Displays the status of the FR WASHER switch in combination switch judged by BCM with the combination switch reading function. Displays the status of the FR WIPER INT/AUTO switch in combination switch judged by BCM with the combination switch reading function. Displays the status of the front wiper stop position signal received from IPDM E/R via CAN communication. Displays the status of wiper volume dial position judged by BCM with the combination switch reading function.
INFOID:0000000005656196
BCS-26
BCM
BCM : CONSULT-III Function (BCM - BCM)
WORK SUPPORT
Item RESET SETTING VALUE Description Return a value set with Work Support of each system to a default value in factory shipment.
INFOID:0000000005656197
IMMU
IMMU : CONSULT-III Function (BCM - IMMU)
DATA MONITOR
Monitor item CONFRM ID ALL CONFIRM ID4 CONFIRM ID3 CONFIRM ID2 CONFIRM ID1 TP 4 TP 3 TP 2 TP 1 PUSH SW KEY SW -SLOT Indicates [ON/OFF] condition of push-button ignition switch. Indicates [ON/OFF] condition of key slot. Indicates [YET] at all time. Switch to [DONE] when a registered Intelligent Key is inserted into the key slot. Content
INFOID:0000000005890806
BCS
O
Indicates the number of ID which has been registered.
ACTIVE TEST
BCS-27
BATTERY SAVER
BATTERY SAVER : CONSULT-III Function (BCM - BATTERY SAVER)
WORK SUPPORT
Service item BATTERY SAVER SET Setting item On* Off On* Off MODE 1* MODE 2 Setting With the exterior lamp battery saver function Without the exterior lamp battery saver function With the interior room lamp battery saver function Without the interior room lamp battery saver function 30 min. 60 min. Sets the interior room lamp battery saver timer operating time.
INFOID:0000000005890810
DATA MONITOR
Monitor item [Unit] REQ SW-DR [On/Off] REQ SW-AS [On/Off] REQ SW-RR [On/Off] REQ SW-RL [On/Off] PUSH SW [On/Off] ACC RLY-F/B [On/Off] KEY SW-SLOT [On/Off] UNLK SEN-DR [On/Off] DOOR SW-DR [On/Off] DOOR SW-AS [On/Off] DOOR SW-RR [On/Off] DOOR SW- RL [On/Off] DOOR SW-BK [On/Off] CDL LOCK SW [On/Off] CDL UNLOCK SW [On/Off] Lock switch status received from the door lock and unlock switch by power window switch serial link Unlock switch status received from the door lock and unlock switch by power window switch serial link NOTE: The item is indicated, but not monitored. Description The switch status input from request switch (driver side) The switch status input from front request switch (passenger side)
The switch status input from push-button ignition switch NOTE: The item is indicated, but not monitored. Key switch status input from key slot Driver door unlock status input from unlock sensor The switch status input driver side front door switch The switch status input from passenger side door switch
BCS-28
ACTIVE TEST
Test item BATTERY SAVER *: Each lamp switch is in ON position. Operation Off On Description Cuts the interior room lamp power supply to turn interior room lamp OFF. Outputs the interior room lamp power supply to turn interior room lamp ON.*
TRUNK
TRUNK : CONSULT-III Function (BCM - TRUNK)
BCM CONSULT-III FUNCTION
CONSULT-III performs the following functions via CAN communication with BCM.
Diagnosis mode DATA MONITOR Function Description The BCM input/output signals are displayed.
INFOID:0000000005890804
DATA MONITOR
Monitor Item PUSH SW UNLK SEN -DR VEH SPEED 1 KEY CYL SW-TR TR CANCEL SW TR/BD OPEN SW TRNK/HAT MNTR RKE-TR/BD TRUNK/GLASS HATCH Contents Indicates [ON/OFF] condition of push switch. Indicates [ON/OFF] condition of unlock sensor. Indicates [Km/h] condition of vehicle speed signal from combination meter. NOTE: This item is displayed, but cannot be monitored. Indicates [ON/OFF] condition of trunk lid opener cancel switch. Indicates [ON/OFF] condition of trunk lid opener switch. Indicates [ON/OFF] condition of trunk room lamp switch. Indicates [ON/OFF] condition of trunk open signal from Intelligent Key remote controller button. This test is able to check trunk lid opener actuator open operation.
BCS
ACTIVE TEST
Test item TRUNK/GLASS HATCH Description This test is able to check trunk lid opener actuator open operation. This actuator opens when OPEN on CONSULT-III screen is touched.
THEFT ALM
THEFT ALM : CONSULT-III Function (BCM - THEFT)
DATA MONITOR
Revision: 2009 November
INFOID:0000000005890805
BCS-29
WORK SUPPORT
Test Item SECURITY ALARM SET THEFT ALM TRG Description This mode is able to confirm and change security alarm ON-OFF setting. The switch which triggered vehicle security alarm is recorded. This mode is able to confirm and erase the record of vehicle security alarm. The trigger data can be erased by touching CLEAR on CONSULT-III screen.
ACTIVE TEST
Test Item THEFT IND VEHICLE SECURITY HORN HEADLAMP(HI) FLASHER Description This test is able to check security indicator lamp operation. The lamp will be turned on when ON on CONSULT-III screen is touched. This test is able to check vehicle security horn operation. The horns will be activated for 0.5 seconds after ON on CONSULT-III screen is touched. This test is able to check vehicle security lamp operation. The headlamps will be activated for 0.5 seconds after ON on CONSULT-III screen is touched. This test is able to check vehicle security hazard lamp operation. The hazard lamps will be activated after ON on CONSULT-III screen is touched.
RETAIND PWR
RETAIND PWR : CONSULT-III Function (BCM - RETAINED PWR)
Data monitor
INFOID:0000000005890807
BCS-30
SIGNAL BUFFER
SIGNAL BUFFER : CONSULT-III Function (BCM - SIGNAL BUFFER)
DATA MONITOR
Monitor item [UNIT] PUSH SW [Off/On] Description Displays the status of the push-button ignition switch (push switch) judged by BCM.
INFOID:0000000005656202
ACTIVE TEST
Test item Operation Off OIL PRESSURE SW On OFF BCM transmits the oil pressure switch signal to the unified meter and A/C amp. via CAN communication, which illuminates the oil pressure warning lamp in the combination meter. Description
INFOID:0000000005890815
BCS
BCS-31
NOTE: Before performing the self-diagnosis, be sure to register the ID, or erase the actual malfunction location may be different from that displayed on CONSULT-III.
BCS-32
DTC/CIRCUIT DIAGNOSIS
U1000 CAN COMM
Description
INFOID:0000000005656205
CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-vehicle multiplex communication line with high data communication speed and excellent error detection ability. Modern vehicle is equipped with many electronic control unit, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with 2 communication lines (CAN H-line, CAN L-line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only. CAN Communication Signal Chart. Refer to LAN-27, "CAN Communication Signal Chart".
DTC Logic
DTC DETECTION LOGIC
DTC CONSULT-III display description CAN COMM DTC Detection Condition When BCM cannot communicate CAN communication signal continuously for 2 seconds or more. Possible cause
INFOID:0000000005656206
U1000
Diagnosis Procedure
INFOID:0000000005656207
BCS
BCS-33
Possible cause
Diagnosis Procedure
1.REPLACE BCM
When DTC U1010 is detected, replace BCM. >> Replace BCM. Refer to BCS-78, "Exploded View".
BCS-34
U0415 is displayed if any unusual condition is present in the reception status of the vehicle speed signal from the ABS actuator and electric unit (control unit).
DTC Logic
DTC DETECTION LOGIC
DTC CONSULT-III display description VEHICLE SPEED DTC Detection Condition When the vehicle speed signal received from the ABS actuator and electric unit (control unit) remains abnormal for 2 seconds or more. Probable cause
INFOID:0000000005656211
U0415
1.DTC CONFIRMATION
Erase the DTC. Turn ignition switch OFF. Perform the Self Diagnostic Result of CONSULT-III, when passed 2 seconds or more after the ignition switch is turned ON. Is any DTC detected? YES >> Refer to BCS-35, "Diagnosis Procedure". NO >> INSPECTION END 1. 2. 3.
Diagnosis Procedure
INFOID:0000000005656212
BCS
BCS-35
1.DTC CONFIRMATION
1. 2. 3. Erase DTC. Turn ignition switch OFF. Perform the Self Diagnostic Result of CONSULT-III, when passed 120 seconds or more after the ignition switch is turned ON. Is any DTC detected? YES >> Refer to BCS-36, "Diagnosis Procedure". NO >> INSPECTION END
Diagnosis Procedure
INFOID:0000000005656214
BCS-36
Is the fuse fusing? YES >> Replace the blown fuse or fusible link after repairing the affected circuit if a fuse or fusible link is blown. NO >> GO TO 2.
Is the measurement value normal? YES >> GO TO 3. NO >> Repair harness or connector.
Does continuity exist? YES >> INSPECTION END NO >> Repair harness or connector.
BCS
BCS-37
Continuity
Does continuity exist? YES >> GO TO 2. NO >> Repair the harnesses or connectors.
Does continuity exist? YES >> Repair the harnesses or connectors. NO >> GO TO 3.
Is the measurement value normal? YES >> GO TO 4. NO >> Replace BCM. Refer to BCS-78, "Exploded View".
Revision: 2009 November
BCS-38
Is the measurement value normal when any of the switches is turned ON? YES >> Replace BCM. Refer to BCS-78, "Exploded View". NO >> Replace the combination switch.
BCS
BCS-39
Continuity
Does continuity exist? YES >> GO TO 2. NO >> Repair the harnesses or connectors.
Does continuity exist? YES >> Repair the harnesses or connectors. NO >> GO TO 3.
BCS-40
D
JPMIA0041GB
OUTPUT 5
8 1.4 V
Is the measurement value normal when any of the switches is turned ON? YES >> Replace BCM. Refer to BCS-78, "Exploded View". NO >> Replace the combination switch.
BCS
BCS-41
Monitor Item FR WIPER HI Other than front wiper switch HI Front wiper switch HI Other than front wiper switch LO Front wiper switch LO Front washer switch OFF Front washer switch ON
Condition
Value/Status Off On Off On Off On Off On Off On Wiper volume dial position Off On Off On Off On Off On Off On Off On Off On Off On Off On Off Off On Off On Off
FR WIPER LOW
FR WASHER SW
FR WIPER INT
Other than front wiper switch INT/AUTO Front wiper switch INT/AUTO Front wiper is not in STOP position Front wiper is in STOP position Wiper volume dial is in a dial position 1 - 7 Other than turn signal switch RH Turn signal switch RH Other than turn signal switch LH Turn signal switch LH Other than lighting switch 1ST and 2ND Lighting switch 1ST or 2ND Other than lighting switch HI Lighting switch HI Other than lighting switch 2ND Lighting switch 2ND Other than lighting switch 2ND Lighting switch 2ND Other than lighting switch PASS Lighting switch PASS Other than lighting switch AUTO Lighting switch AUTO Front fog lamp switch OFF Front fog lamp switch ON NOTE: The item is indicated, but not monitored. Driver door closed Driver door opened Passenger door closed Passenger door opened NOTE: The item is indicated, but not monitored.
TURN SIGNAL L
TAIL LAMP SW
HI BEAM SW
HEAD LAMP SW 1
HEAD LAMP SW 2
PASSING SW
AUTO LIGHT SW
BCS-42
A
Off Off Off On Off On Off On Off On Off
CDL UNLOCK SW
KEY CYL UN-SW KEY CYL SW-TR HAZARD SW REAR DEF SW H/L WASH SW TR CANCEL SW
F
Off On Off Off Off On Off On Off On Off On Off On Off On Off On Off On Off On Close to 5 V Close to 0 V Off On Off On Off
TR/BD OPEN SW
TRNK/HAT MNTR
RKE-LOCK
RKE-UNLOCK
RKE-TR/BD
RKE-PANIC
BCS
RKE-P/W OPEN
RKE-MODE CHG
REQ SW -DR
BCS-43
PUSH SW
BRAKE SW 2
DETE/CANCL SW
SFT PN/N SW
S/L -LOCK
S/L -UNLOCK
S/L RELAY-F/B
PUSH SW -IPDM
DETE SW -IPDM
SFT PN -IPDM
SFT P -MET
SFT N -MET
BCS-44
S/L UNLK-IPDM
S/L RELAY-REQ
PRMT ENG STRT PRMT RKE STRT KEY SW -SLOT RKE OPE COUN1 RKE OPE COUN2
BCS
CONFRM ID ALL
N
Done Yet Done
CONFIRM ID4
P
Yet Done
CONFIRM ID3
BCS-45
CONFIRM ID2
CONFIRM ID1
TP 4
TP 3
TP 2
TP 1 AIR PRESS FL AIR PRESS FR AIR PRESS RR AIR PRESS RL ID REGST FL1
ID REGST FR1
ID REGST RR1
ID REGST RL1
WARNING LAMP
BUZZER
BCS-46
BCS
O
JPMIA0062ZZ
PHYSICAL VALUES
BCS-47
Ignition switch OFF Ignition switch OFF Ignition switch ON Interior room lamp battery saver is activated. (Cuts the interior room lamp power supply)
4 (LG)
Ground
Output
Interior room lamp battery saver is not activated. (Outputs the interior room lamp power supply) Passenger door UNLOCK (Actuator is activated) Other than UNLOCK (Actuator is not activated) ON OFF LOCK (Actuator is activated) Other than LOCK (Actuator is not activated) UNLOCK (Actuator is activated) Other than UNLOCK (Actuator is not activated)
12 V
5 (P)
Ground
12 V 0V 0V 12 V 12 V 0V 12 V 0V Battery voltage 0V 0V NOTE: When the illumination brightening/dimming level is in the neutral position.
Output
7 (SB)
Ground
Step lamp
Output
Step lamp
8 (V)
Ground
Output
Ground
Output
Ground Ground
Input
14 (W)
Ground
Output
Tail lamp
ON
JSNIA0010GB
15 (BG)
Ground
Output
Ignition switch
Battery voltage 0V
BCS-48
17 (W)
Ground
Output
Ignition switch ON
C
Turn signal switch RH
D
PKID0926E
18 (BG)
Ground
Output
Ignition switch ON
F
Turn signal switch LH
G
PKID0926E
6.5 V 19 (V) Ground Room lamp timer control Output Interior room lamp OFF ON Turn signal switch OFF 12 V 0V 0V
20 (V)
Ground
Output
Ignition switch ON
PKID0926E
6.5 V OPEN (Trunk lid opener actuator is activated) Other than OPEN (Trunk lid opener actuator is not activated) Turn signal switch OFF 12 V
23 (L)
Ground
Output
Trunk lid
0V 0V
BCS
N
25 (Y) Ignition switch ON
Ground
Output
PKID0926E
6.5 V 30 (P) Ground Trunk room lamp Output Trunk room lamp ON OFF 0V 12 V
BCS-49
34 (SB)
Ground
Output
35 (V)
Ground
Output
When Intelligent Key is in the antenna detection area When the trunk lid opener request switch is operated with ignition switch OFF When Intelligent Key is not in the antenna detection area
JMKIA0063GB JMKIA0062GB
38 (B)
Ground
Output
BCS-50
B
When Intelligent Key is in the antenna detection area When the trunk lid opener request switch is operated with ignition switch OFF When Intelligent Key is not in the antenna detection area
JMKIA0063GB JMKIA0062GB
39 (W)
Ground
Output
47 (Y)
Ground
Output
Ignition switch
OFF or ACC ON
12 V 0V
50 (G)
Ground
Input
JPMIA0011GB
11.8 V ON (Trunk lid is opened) Ignition switch ON (A/T models) 52 (SB) Ground Starter relay control Output Ignition switch ON (M/T models) When selector lever is in P or N position When selector lever is not in P or N position When the clutch pedal is depressed When the clutch pedal is not depressed ON (Pressed) 0V 12 V 0V
L
Battery voltage 0V 0V
BCS
N
61 (SB) Trunk lid opener request switch Trunk lid opener request switch
Ground
Input
JPMIA0016GB
1.0 V 64 (P) Ground Intelligent Key warning buzzer (Engine room) Output Intelligent Key warning buzzer (Engine room) Sounding Not sounding 0V 12 V
BCS-51
67 (GR)
Ground
Input
Not pressed
JPMIA0011GB
11.8 V
72 (R)
Ground
Output
73 (G)
Ground
Output
BCS-52
B
When Intelligent Key is in the antenna detection area When the passenger door request switch is operated with ignition switch OFF When Intelligent Key is not in the antenna detection area
JMKIA0063GB JMKIA0062GB
74 (SB)
Ground
Output
When Intelligent Key is in the antenna detection area When the passenger door request switch is operated with ignition switch OFF When Intelligent Key is not in the antenna detection area
JMKIA0063GB JMKIA0062GB
75 (BR)
Ground
Output
BCS
When Intelligent Key is in the antenna detection area When the driver door request switch is operated with ignition switch OFF When Intelligent Key is not in the antenna detection area
JMKIA0063GB JMKIA0062GB
76 (V)
Ground
Output
BCS-53
When Intelligent Key is in the antenna detection area When the driver door request switch is operated with ignition switch OFF When Intelligent Key is not in the antenna detection area
JMKIA0063GB JMKIA0062GB
77 (LG)
Ground
Output
78 (Y)
Ground
Output
79 (BR)
Ground
Output
BCS-54
Ground
During waiting
Ground
Ignition switch
E
During waiting
F
JMKIA0064GB
83 (Y)
Ground
Input/ Output
JMKIA0065GB
J
All switches OFF (Wiper volume dial 4)
K
JPMIA0041GB
1.4 V
BCS
87 (Y) Ground Combination switch INPUT 5 Input Combination switch Front fog lamp switch ON (Wiper volume dial 4)
N
JPMIA0037GB
1.3 V
O
Any of the conditions below with all switches OFF Wiper volume dial 1 Wiper volume dial 2 Wiper volume dial 6 Wiper volume dial 7
JPMIA0040GB
1.3 V
BCS-55
JPMIA0041GB
1.4 V
JPMIA0036GB
88 (GR)
Ground
Input
Combination switch
1.3 V
JPMIA0037GB
1.3 V
Any of the conditions below with all switches OFF Wiper volume dial 1 Wiper volume dial 2 Wiper volume dial 3
JPMIA0040GB
1.3 V 89 (BR) 90 (P) 91 (L) Ground Push-button ignition switch (Push switch) CAN-L CAN-H Input Input/ Output Input/ Output Push-button ig- Pressed nition switch Not pressed (push switch) OFF 0V Battery voltage 0V
Ground Ground
92 (LG)
Ground
Output
Blinking
JPMIA0015GB
6.5 V ON 12 V
BCS-56
ON indicator lamp
Ground
Output
Ground
Input
Steering lock
Ground
Input
Steering lock
Selector lever
Input
H
0V 12 V 0V
J
100 (Y) Ground Passenger door request switch Input Passenger door request switch
JPMIA0016GB
1.0 V ON (Pressed) 0V
BCS
101 (R) Driver door request switch Driver door request switch
Ground
Input
JPMIA0016GB
1.0 V 102 (BG) 103 (LG) 106 (W) Ground Blower fan motor relay control Remote keyless entry receiver power supply Steering lock unit power supply Output Ignition switch OFF or ACC ON 0V 12 V 12 V 12 V 0V
Ground
Output
Ground
Output
Ignition switch
BCS-57
JPMIA0041GB
1.4 V
JPMIA0037GB
1.3 V
107 (LG)
Ground
Input
JPMIA0036GB
1.3 V
JPMIA0038GB
1.3 V
JPMIA0039GB
1.3 V
BCS-58
B
All switches OFF (Wiper volume dial 4)
JPMIA0041GB
1.4 V
E
Lighting switch AUTO (Wiper volume dial 4)
F
JPMIA0038GB
108 (R)
Ground
Input
Combination switch
1.3 V
JPMIA0036GB
1.3 V
J
Any of the conditions below with all switches OFF Wiper volume dial 1 Wiper volume dial 5 Wiper volume dial 6
JPMIA0039GB
1.3 V
BCS
BCS-59
JPMIA0041GB
1.4 V
JPMIA0037GB
1.3 V
109 (W)
Ground
Input
JPMIA0036GB
1.3 V
JPMIA0038GB
1.3 V
JPMIA0040GB
1.3 V ON 0V
110 (G)
Ground
Hazard switch
Input
Hazard switch
OFF
JPMIA0012GB
1.1 V
BCS-60
C
LOCK or UNLOCK 111 (Y) Ground Steering lock unit communication Input/ Output Steering lock
D
JMKIA0066GB
12 V 0V
112 (R)
Ground
Input/ Output
G
Ignition switch ON
H
JPMIA0156GB
8.7 V 113 (BG) Ignition switch ON When bright outside of the vehicle When dark outside of the vehicle OFF (Clutch pedal is not depressed) ON (Clutch pedal is depressed) OFF (Brake pedal is not depressed) ON (Brake pedal is depressed) Close to 5 V Close to 0 V
Ground
Optical sensor
Input
J
0V Battery voltage Battery voltage
Ground
Input
Ground
Input
L
0V Battery voltage 0V Battery voltage
Stop lamp switch 2 (Without ICC) 118 (BR) Ground Stop lamp switch 2 (With ICC) Input
BCS
Stop lamp switch OFF (Brake pedal is not depressed) and ICC brake hold relay OFF Stop lamp switch ON (Brake pedal is depressed) or ICC brake hold relay ON
O
LOCK status (Unlock sensor switch OFF)
JPMIA0012GB
119 (SB)
Ground
Input
Driver door
BCS-61
Ground
Input
123 (W)
Ground
IGN feedback
Input
124 (LG)
Ground
Input
JPMIA0011GB
129 (Y)
Ground
Input
CANCEL
JPMIA0012GB
1.1 V ON 0V
132 (V)
Ground
Input/ Output
Ignition switch ON
JPMIA0013GB
10.2 V Ignition switch OFF or ACC ON (Tail lamps OFF) 12 V 9.5 V NOTE: The pulse width of this wave is varied by the illumination brightening/dimming level. 133 (L) Ground Push-button ignition switch illumination Output Push-button ignition switch il- ON (Tail lamps ON) lumination
JPMIA0159GB
OFF 134 (R) 137 (BG) Ground Ground LOCK indicator lamp Receiver and sensor ground Output Input LOCK indicator lamp OFF ON
0V Battery voltage 0V 0V
Ignition switch ON
BCS-62
C
Standby state
D
139 (L) Ground Tire pressure receiver communication Input/ Output Ignition switch ON
OCC3881D
OCC3880D
140 (Y)
Ground
Input
Selector lever
12 V 0V 0V
I
141 (P) Ground Security indicator Output Security indicator Blinking
J
JPMIA0014GB
11.3 V OFF All switches OFF Lighting switch 1ST Combination switch (Wiper volume dial 4) Lighting switch HI Lighting switch 2ND 12 V 0V
142 (LG)
Ground
Output
BCS
Turn signal switch RH
JPMIA0031GB
10.7 V All switches OFF (Wiper volume dial 4) Front wiper switch HI (Wiper volume dial 4) 143 (V) Ground Combination switch OUTPUT 1 Output Combination switch Any of the conditions below with all switches OFF Wiper volume dial 1 Wiper volume dial 2 Wiper volume dial 3 Wiper volume dial 6 Wiper volume dial 7 0V
JPMIA0032GB
10.7 V
BCS-63
JPMIA0033GB
10.7 V All switches OFF Front fog lamp switch ON Combination switch (Wiper volume dial 4) Lighting switch 2ND Lighting switch PASS 0V
146 (SB)
Ground
Output
10.7 V 149 (W) Ground Tire pressure warning check switch Input 12 V
150 (R)
Ground
Input
JPMIA0011GB
11.8 V ON (Door open) 151 (G) Ground Rear window defogger relay control Output Rear window defogger Active Not activated 0V 0V Battery voltage
BCS-64
INFOID:0000000005656219
BCS
JCMWM5999GB
BCS-65
JCMWM6000GB
BCS-66
BCS
O
JCMWM6001GB
BCS-67
JCMWM6002GB
BCS-68
BCS
O
JCMWM6003GB
BCS-69
JCMWM6004GB
Fail-safe
FAIL-SAFE CONTROL BY DTC
BCM performs fail-safe control when any DTC are detected.
INFOID:0000000005656220
BCS-70
B2604: PNP/CLUTCH SW
BCS
B2605: PNP/CLUTCH SW
BCS-71
Maintains the power supply position attained at the time of DTC detection
Inhibit engine cranking Inhibit engine cranking Inhibit engine cranking Inhibit engine cranking
B26E8: CLUTCH SW
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority chart.
Priority 1 2 B2562: LOW VOLTAGE U1000: CAN COMM U1010: CONTROL UNIT(CAN) B2190: NATS ANTENNA AMP B2191: DIFFERENCE OF KEY B2192: ID DISCORD BCM-ECM B2193: CHAIN OF BCM-ECM B2195: ANTI-SCANNING DTC
BCS-72
BCS
DTC Index
NOTE: The details of time display are as follows. CRNT: A malfunction is detected now. PAST: A malfunction was detected in the past. IGN counter is displayed on Freeze Frame Data. For details of Freeze Frame Data, refer to BCS-14, "COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)".
BCS-73
CONSULT display
Fail-safe
Reference page
No DTC is detected. further testing may be required. U1000: CAN COMM U1010: CONTROL UNIT(CAN) U0415: VEHICLE SPEED B2013: ID DISCORD BCM-S/L B2014: CHAIN OF S/L-BCM B2190: NATS ANTENNA AMP B2191: DIFFERENCE OF KEY B2192: ID DISCORD BCM-ECM B2193: CHAIN OF BCM-ECM B2195: ANTI-SCANNING B2553: IGNITION RELAY B2555: STOP LAMP B2556: PUSH-BTN IGN SW B2557: VEHICLE SPEED B2560: STARTER CONT RELAY B2562: LOW VOLTAGE B2601: SHIFT POSITION B2602: SHIFT POSITION B2603: SHIFT POSI STATUS B2604: PNP/CLUTCH SW B2605: PNP/CLUTCH SW B2606: S/L RELAY B2607: S/L RELAY B2608: STARTER RELAY B2609: S/L STATUS B260A: IGNITION RELAY B260B: STEERING LOCK UNIT B260C: STEERING LOCK UNIT B260D: STEERING LOCK UNIT B260F: ENG STATE SIG LOST B2612: S/L STATUS B2614: BCM B2615: BCM B2616: BCM B2617: BCM B2618: BCM B2619: BCM B261A: PUSH-BTN IGN SW B261E: VEHICLE TYPE
BCS-33 BCS-34 BCS-35 SEC-55 SEC-56 SEC-47 SEC-50 SEC-51 SEC-53 SEC-54 PCS-48 SEC-59 SEC-61 SEC-63 SEC-64 BCS-36 SEC-65 SEC-68 SEC-70 SEC-73 SEC-75 SEC-77 SEC-78 SEC-80 SEC-82 PCS-50 SEC-86 SEC-87 SEC-88 SEC-89 SEC-94 PCS-52 PCS-54 PCS-56 SEC-98 PCS-58 SEC-100 PCS-59 SEC-101
BCS-74
B2621: INSIDE ANTENNA B2622: INSIDE ANTENNA B2623: INSIDE ANTENNA B26E8: CLUTCH SW B26E9: S/L STATUS B26EA: KEY REGISTRATION C1704: LOW PRESSURE FL C1705: LOW PRESSURE FR C1706: LOW PRESSURE RR C1707: LOW PRESSURE RL C1708: [NO DATA] FL C1709: [NO DATA] FR C1710: [NO DATA] RR C1711: [NO DATA] RL C1716: [PRESSDATA ERR] FL C1717: [PRESSDATA ERR] FR C1718: [PRESSDATA ERR] RR C1719: [PRESSDATA ERR] RL C1729: VHCL SPEED SIG ERR C1734: CONTROL UNIT
D
SEC-93
BCS
BCS-75
SYMPTOM DIAGNOSIS
COMBINATION SWITCH SYSTEM SYMPTOMS
Symptom Table
1. 2. Perform Data Monitor of CONSULT-III to check for any malfunctioning item. Check the malfunction combinations.
Malfunction item:
INFOID:0000000005656223
Data monitor item HEAD LAMP SW 1 HEAD LAMP SW 2 AUTO LIGHT SW FR WASHER SW TURN SIGNAL R TURN SIGNAL L FR WIPER LOW TAIL LAMP SW FR WIPER INT PASSING SW FR WIPER HI INT VOLUME HI BEAM SW FR FOG SW
Malfunction combination
A B C D E F G H I J K L
All Items
If only one item is detected or the item is not applicable to the combinations A to K
3.
Identify the malfunctioning part from the agreed combination and repair or replace the part.
Malfunction combination A B C D E F G H I J K L Malfunctioning part Combination switch INPUT 1 circuit Combination switch INPUT 2 circuit Combination switch INPUT 3 circuit Combination switch INPUT 4 circuit Combination switch INPUT 5 circuit Combination switch OUTPUT 1 circuit Combination switch OUTPUT 2 circuit Combination switch OUTPUT 3 circuit Combination switch OUTPUT 4 circuit Combination switch OUTPUT 5 circuit BCM Combination switch Replace BCM. Refer to BCS-78, "Exploded View" Replace the combination switch. Inspect the combination switch output circuit applicable to the malfunctioning part. Refer to BCS-40, "Diagnosis Procedure". Inspect the combination switch input circuit applicable to the malfunctioning part. Refer to BCS-38, "Diagnosis Procedure". Repair or replace
BCS-76
PRECAUTIONS
< PRECAUTION >
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"
INFOID:0000000005656224
The Supplemental Restraint System such as AIR BAG and SEAT BELT PRE-TENSIONER, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. Information necessary to service the system safely is included in the SRS AIR BAG and SEAT BELT of this Service Manual. WARNING: To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer. Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see the SRS AIR BAG. Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors.
INFOID:0000000005656225
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interference between the window edge and the vehicle when the door is opened/closed. During normal operation, the window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic window function will not work with the battery disconnected.
BCS
BCS-77
JPMIA0063ZZ
1.
BCM
INFOID:0000000005656227
INSTALLATION
Install in the reverse order of removal.
BCS-78
COMBINATION SWITCH
< REMOVAL AND INSTALLATION >
COMBINATION SWITCH
Exploded View
INFOID:0000000005656228
F
JPLIA0050ZZ
1.
Combination switch
2.
Remove steering column cover. Refer to IP-12, "A/T MODELS : Exploded View" (A/T models), IP-22, "M/ T MODELS : Exploded View" (M/T models). Remove screws. Disconnect the connector. Pull up the combination switch to remove it.
INSTALLATION
Install in the reverse order of removal.
K
BCS
BCS-79