Académique Documents
Professionnel Documents
Culture Documents
Benefits
Hilti HITHY 150 MAX
330 ml foil pack
(also available
as 500 ml
and 1400 ml
foil pack)
Static mixer
HAS rods
HAS-R rods
HAS-HCR rods
HAS-E rods
HAS-E-R rods
HIT-V rods
HIT-V-R rods
HIT-V-HCR rods
Concrete
Tensile
zone
Small edge
distance
and spacing
Variable
embedment
depth
Corrosion
resistance
High
corrosion
resistance
European
Technical
Approval
CE
conformity
Hilti anchor
design
software
Approvals / certificates
Description
European technical approval
a)
Authority / Laboratory
DIBt, Berlin
500
6 / 2010
Embedment depth a) and base material thickness for the basic loading data.
Mean ultimate resistance, characteristic resistance, design resistance, recommended loads.
Anchor size
M8
M10
M12
M16
M20
M24
M27
Typical embedment depth hef [mm]
80
90
110
125
170
210
240
Base material thickness h [mm]
110
120
140
165
220
270
300
a) The allowed range of embedment depth is shown in the setting details. The corresponding load values
calculated according to the simplified design method.
M30
270
340
can be
M8
M10
M12
M16
M20
M24
M27
M30
Tensile NRu,m
HIT-V 5.8
[kN]
18,9
30,5
44,1
83,0
129,2
185,9
241,5
288,4
Shear VRu,m
HIT-V 5.8
[kN]
9,5
15,8
22,1
41,0
64,1
92,4
120,8
147,0
Cracked concrete
Tensile NRu,m HIT-V 5.8
[kN]
20,7
30,4
50,3
85,5
126,7
Shear VRu,m
[kN]
15,8
22,1
41,0
64,1
92,4
HIT-V 5.8
M8
M10
M12
M16
M20
M24
M27
M30
Tensile NRk
HIT-V 5.8
[kN]
18,0
29,0
42,0
70,6
111,9
153,7
187,8
216,3
Shear VRk
HIT-V 5.8
[kN]
9,0
15,0
21,0
39,0
61,0
88,0
115,0
140,0
Cracked concrete
Tensile NRk
HIT-V 5.8
[kN]
15,6
22,8
37,7
64,1
95,0
Shear VRk
[kN]
15,0
21,0
39,0
61,0
88,0
HIT-V 5.8
HIT-V 5.8
M8
M10
M12
M16
M20
M24
M27
M30
[kN]
12,0
19,3
28,0
47,1
74,6
102,5
125,2
120,2
[kN]
7,2
12,0
16,8
31,2
48,8
70,4
92,0
112,0
Cracked concrete
Tensile NRd
HIT-V 5.8
[kN]
10,4
15,2
25,1
42,7
63,3
Shear VRd
HIT-V 5.8
[kN]
12,0
16,8
31,2
48,8
70,4
6 / 2010
501
M8
M10
M12
M16
M20
M24
M27
M30
[kN]
8,6
13,8
20,0
33,6
53,3
73,2
89,4
85,8
Shear Vrec
HIT-V 5.8
[kN]
5,1
8,6
12,0
22,3
34,9
50,3
65,7
80,0
Cracked concrete
Tensile Nrec
HIT-V 5.8
[kN]
7,4
10,9
18,0
30,5
45,2
Shear Vrec
[kN]
8,6
12,0
22,3
34,9
50,3
HIT-V 5.8
a) With overall partial safety factor for action = 1,4. The partial safety factors for action depend on the type of
loading and shall be taken from national regulations. According ETAG 001, annex C, the partial safety factor is
G = 1,35 for permanent actions and Q = 1,5 for variable actions.
Base material
temperature
Temperature range
Temperature range I
Temperature range II
Temperature range III
-40 C to +40 C
-40 C to +80 C
-40 C to +120 C
Materials
Mechanical properties of HIT-V / HAS
Anchor size
HIT-V/HAS 5.8
Nominal
HIT-V/HAS 8.8
tensile
strength f uk HIT-V/HAS -R
HIT-V/HAS -HCR
HIT-V/HAS 5.8
HIT-V/HAS 8.8
Yield
strength fyk HIT-V/HAS -R
HIT-V/HAS -HCR
Stressed
HAS
crosssection As HIT-V
Moment of HAS
resistance
HIT-V
W
502
[N/mm]
[N/mm]
[N/mm]
[N/mm]
[N/mm]
[N/mm]
[N/mm]
[N/mm]
M8
500
800
700
800
400
640
450
600
M10
500
800
700
800
400
640
450
600
M12
500
800
700
800
400
640
450
600
M16
500
800
700
800
400
640
450
600
M20
500
800
700
800
400
640
450
600
M24
500
800
700
700
400
640
450
400
M27
500
800
500
700
400
640
210
400
M30
500
800
500
700
400
640
210
400
[mm]
32,8
52,3
76,2
144
225
324
427
519
[mm]
36,6
58,0
84,3
157
245
353
459
561
[mm]
27,0
54,1
93,8
244
474
809
1274
1706
[mm]
31,2
62,3
109
277
541
935
1387
1874
6 / 2010
Material quality
Part
Threaded rod
HIT-V(F),
HAS 5.8: M8 M24
Threaded rod
HIT-V(F),
HAS 8.8 M27 M30
Material
Strength class 5.8, EN ISO 898-1, A5 > 8% ductile
steel galvanized 5 m, EN ISO 4042
(F) hot dipped galvanized 45 m, EN ISO 10684
Strength class 8.8, EN ISO 898-1, A5 > 8% ductile
steel galvanized 5 m, EN ISO 4042
(F) hot dipped galvanized 45 m, EN ISO 10684
Stainless steel grade A4, A5 > 8% ductile
strength class 70 for M24 and class 50 for M27 to M30, EN ISO 3506-1,
EN 10088: 1.4401; 1.4404; 1.4578; 1.4571; 1.4439; 1.4362
High corrosion resistant steel, EN ISO 3506-1, EN 10088: 1.4529; 1.4565
strength M20: Rm = 800 N/mm, Rp 0.2 = 640 N/mm, A5 > 8% ductile
M24 to M30: Rm = 700 N/mm, Rp 0.2 = 400 N/mm, A5 > 8% ductile
Steel galvanized, EN ISO 4042; hot dipped galvanized, EN ISO 10684
Stainless steel, EN 10088: 1.4401; 1.4404; 1.4578; 1.4571; 1.4439;
1.4362
High corrosion resistant steel, EN 10088: 1.4529; 1.4565
Strength class 8, ISO 898-2
steel galvanized 5 m, EN ISO 4042
hot dipped galvanized 45 m, EN ISO 10684
Strength class 70, EN ISO 3506-2, stainless steel grade A4,
EN 10088: 1.4401; 1.4404; 1.4578; 1.4571; 1.4439; 1.4362
Strength class 70, EN ISO 3506-2, high corrosion resistant steel,
EN 10088: 1.4529; 1.4565
Threaded rod
HIT-V-R, HAS-R
Threaded rod
HIT-V-HCR, HAS-HCR
Washer
ISO 7089
Nut
EN ISO 4032
Anchor dimensions
M30
M30x270
M27
M27x240
M24
M24x210
[mm]
M20
M20x170
hef
M16
M16x125
Embedment depth
M12
M12x110
Anchor rod
HAS, HAS-R, HAS-HCR
HAS-E, HAS-E-R
M10
M10x90
M8
M8x80
Anchor size
80
90
110
125
170
210
240
270
Anchor rod
HIT-V, HIT-V-R, HIT-V-HCR
Setting
installation equipment
Anchor size
Rotary hammer
Other tools
6 / 2010
M8
M10
M12
M16
M20
M24
M27
M30
TE 2 TE 16
TE 40 TE 70
compressed air gun or blow out pump, set of cleaning brushes, dispenser
503
Setting instruction
Dry and water-saturated concrete, hammer drilling
a)
b)
a) Note: Manual cleaning for non-cracked concrete, element sizes d 16mm and embedment depth
hef 10 d only!
b) Note: Extension and piston plug needed for overhead installation and/or embedment depth > 250mm!
For detailed information on installation see instruction for use given with the package of the product.
504
6 / 2010
Working time
tgel
180 min
40 min
20 min
8 min
5 min
2 min
Curing time
tcure
12 h
4 h
2 h
1 h
30 min
30 min
Setting details
d0
Marking of the
embedment depth
df
Fixture
Thickness tfix
6 / 2010
505
Setting details
Anchor size
Nominal diameter of
drill bit
M8
M10
M12
M16
M20
M24
M27
M30
d0
[mm]
10
12
14
18
24
28
30
35
hef,min
[mm]
60
60
70
80
90
100
110
120
hef,max
[mm]
160
200
240
320
400
480
540
600
hef
[mm]
80
90
110
125
170
210
240
270
Minimum base
material thickness
hmin
[mm]
Diameter of clearance
df
hole in the fixture
b)
hef + 30 mm
100 mm
hef + 2 d0
[mm]
12
14
18
22
26
30
33
[Nm]
10
20
40
80
150
200
270
300
Torque moment
Tmax
Minimum spacing
smin
[mm]
40
50
60
80
100
120
135
150
cmin
[mm]
40
50
60
80
100
120
135
150
scr,sp
[mm]
Minimum edge
distance
Critical spacing
for splitting failure
ccr,sp
[mm]
2 ccr,sp
1,0 hef
2,26 hef
scr,N
[mm]
2 ccr,N
ccr,N
[mm]
1,5 hef
For spacing (or edge distance) smaller than critical spacing (or critical edge distance) the design loads have to be
reduced.
a)
b)
Maximum recommended torque moment to avoid splitting failure during installation with minimum spacing
and/or edge distance.
c)
d)
The critical edge distance for concrete cone failure depends on the embedment depth hef and the design bond
resistance. The simplified formula given in this table is on the save side.
506
6 / 2010
TENSION loading
The design tensile resistance is the lower value of
- Steel resistance:
NRd,s
6 / 2010
[kN]
[kN]
[kN]
[kN]
[kN]
[kN]
[kN]
[kN]
M8
11,3
12,0
19,3
12,3
13,9
18,0
19,3
M10
17,3
19,3
30,7
19,8
21,9
28,0
30,7
M12
25,3
28,0
44,7
28,3
31,6
40,7
44,7
M16
48,0
52,7
84,0
54,0
58,8
76,7
84,0
M20
74,7
82,0
130,7
84,0
92,0
120,0
130,7
M24
106,7
118,0
188,0
119,8
132,1
106,7
117,6
M27
153,3
231,3
244,7
75,9
80,4
144,8
152,9
M30
187,3
281,3
299,3
92,0
98,3
175,7
187,1
507
M8
M10
M12
M16
M20
M24
M27
M30
80
90
110
125
170
210
240
270
15,6
13,4
8,9
22,0
18,8
12,6
32,3
27,6
18,4
54,5
50,3
29,3
85,5
78,3
46,3
116,1
105,6
63,3
135,7
122,1
74,6
120,2
99,0
63,6
10,4
8,5
5,7
15,2
13,8
8,3
25,1
23,0
14,7
42,7
42,7
24,9
63,3
63,3
42,2
M27
125,2
-
M30
124,5
-
Design concrete cone resistance NRd,c = N0Rd,c fB f1,N f2,N f3,N fh,N fre,N
Design splitting resistance a) NRd,sp = N0Rd,c fB f1,sp f2,sp f3,sp f h,N fre,N
Anchor size
M8
M10
M12
M16
M20
20,1
24,0
32,4
47,1
74,6
N0Rd,c Non-cracked concrete [kN]
20,5
27,7
33,5
53,2
N0Rd,c Cracked concrete
[kN]
a)
Splitting resistance must only be considered for non-cracked concrete.
M24
102,5
73,0
Influencing factors
Influence of concrete strength on combined pull-out and concrete cone resistance
Concrete strength designation
(ENV 206)
C 20/25
C 25/30
C 30/37
C 35/45
C 40/50
0,10 a)
1,00
1,02
1,04
1,06
1,07
f B,p = (f ck,cube/25N/mm)
a) fck,cube = concrete compressive strength, measured on cubes with 150 mm side length
C 45/55
C 50/60
1,08
1,09
C 20/25
C 25/30
C 30/37
C 35/45
C 40/50
fB =
(f ck,cube/25N/mm)0,5 a)
1
1,1
1,22
1,34
1,41
a) fck,cube = concrete compressive strength, measured on cubes with 150 mm side length
C 45/55
C 50/60
1,48
1,55
0,7 + 0,3c/ccr,N 1
0,1
0,2
0,3
0,4
0,5
0,6
0,7
0,8
0,9
0,73
0,76
0,79
0,82
0,85
0,88
0,91
0,94
0,97
0,5(1 + c/ccr,N) 1
508
6 / 2010
0,1
s/scr,sp
f 3,N =
0,2
0,3
0,4
0,5
0,6
0,7
0,8
0,9
0,5(1 + s/scr,N) 1
40
50
60
70
80
90
100
0,7 a)
0,75 a)
0,8 a)
0,85 a)
0,9 a)
0,95 a)
1
f re,N = 0,5 + hef/200mm 1
a) This factor applies only for dense reinforcement. If in the area of anchorage there is reinforcement with a
spacing 150 mm (any diameter) or with a diameter 10 mm and a spacing 100 mm, then a factor fre,N = 1
may be applied.
SHEAR loading
The design shear resistance is the lower value of
- Steel resistance:
-
VRd,s
VRd,cp = k lower value of NRd,p and NRd,c
VRd,c = V0Rd,c fB f f h f4 f hef fc
[kN]
[kN]
[kN]
[kN]
[kN]
[kN]
[kN]
[kN]
M8
6,8
7,2
12,0
7,7
8,3
10,4
12,0
M10
10,4
12,0
18,4
12,2
12,8
16,8
18,4
M12
15,2
16,8
27,2
17,3
19,2
24,8
27,2
M16
28,8
31,2
50,4
32,7
35,3
46,4
50,4
M20
44,8
48,8
78,4
50,6
55,1
72,0
78,4
M24
64,0
70,4
112,8
71,8
79,5
64,0
70,9
M27
92,0
139,2
147,2
45,8
48,3
86,9
92,0
M30
112,0
168,8
179,2
55,5
58,8
105,7
112,0
Design concrete pryout resistance VRd,cp = lower valuea) of k NRd,p and k NRd,c
k = 2 for hef 60 mm
a)
6 / 2010
509
= V0Rd,c fB f f h f4 f hef fc
M8
M10
M12
M16
M20
M24
M27
M30
[kN]
5,9
8,6
11,6
18,7
27,0
36,6
44,5
53,0
[kN]
6,1
8,2
13,2
19,2
25,9
31,5
Influencing factors
Influence of concrete strength
Concrete strength designation
(ENV 206)
C 20/25
C 25/30
C 30/37
C 35/45
C 40/50
fB =
(f ck,cube/25N/mm)1/2 a)
1
1,1
1,22
1,34
1,41
a) fck,cube = concrete compressive strength, measured on cubes with 150 mm side length
C 45/55
C 50/60
1,48
1,55
Influence of angle between load applied and the direction perpendicular to the free edge
Angle
10
20
30
40
50
60
70
80
90
1,01
1,05
1,13
1,24
1,40
1,64
1,97
2,32
2,50
0,15
0,3
0,45
0,6
0,75
0,9
1,05
1,2
1,35
1,5
0,32
0,45
0,55
0,63
0,71
0,77
0,84
0,89
0,95
1,00
510
{h/(1,5 c)}
1/2
6 / 2010
Influence of anchor spacing and edge distance a) for concrete edge resistance: f4
f4 = (c/hef)1,5 (1 + s / [3 c]) 0,5
Single
anchor 0,75 1,50
0,50
0,35
0,27 0,35
0,75
0,65
0,43 0,54
1,00
1,00
0,63 0,75
1,25
1,40
0,84 0,98
1,50
1,84
1,07 1,22
1,75
2,32
1,32 1,49
2,00
2,83
1,59 1,77
2,25
3,38
1,88 2,06
2,50
3,95
2,17 2,37
2,75
4,56
2,49 2,69
3,00
5,20
2,81 3,03
3,25
5,86
3,15 3,38
3,50
6,55
3,51 3,74
3,75
7,26
3,87 4,12
4,00
8,00
4,25 4,50
4,25
8,76
4,64 4,90
4,50
9,55
5,04 5,30
4,75
10,35 5,45 5,72
5,00
11,18 5,87 6,15
5,25
12,03 6,30 6,59
5,50
12,90 6,74 7,04
a) The anchor spacing and the
minimum edge distance cmin.
c/hef
10,50 11,25
0,35 0,35
0,65 0,65
1,00 1,00
1,40 1,40
1,84 1,84
2,32 2,32
2,83 2,83
3,38 3,38
3,95 3,95
4,56 4,56
5,20 5,20
5,86 5,86
6,55 6,55
7,02 7,26
7,50 7,75
7,99 8,25
8,49 8,75
8,99 9,26
9,50 9,78
10,02 10,31
10,55 10,85
smin and the
1,68
0,05 (hef / d)
hef/d
f hef =
1,68
0,05 (hef / d)
4,5
10
11
0,51
0,63
0,75
1,01
1,31
1,64
2,00
2,39
2,81
12
13
14
15
16
17
18
19
20
3,25
3,72
4,21
4,73
5,27
5,84
6,42
7,04
7,67
20
30
40
0,57
0,52
0,50
c/d
0,19
10
15
0,77
0,71
0,67
0,65
0,60
fc =
(d / c)
a) The edge distance shall not be smaller than the minimum edge distance cmin.
6 / 2010
511
M8
M10
M12
M16
M20
M24
M27
M30
hef = hef,min
[mm]
60
60
70
80
90
100
110
120
h = hmin
[mm]
100
100
100
116
138
156
170
190
11,7
13,0
16,4
24,1
28,7
33,7
38,8
36,9
6,9
9,7
16,1
20,5
24,0
48,8
57,5
55,1
57,5
67,3
67,3
67,3
67,3
77,7
77,7
48,3
77,7
88,5
88,5
58,8
88,5
41,0
41,0
41,0
41,0
48,0
48,0
48,0
48,0
M8
M10
M12
M16
M20
M24
M27
M30
hef = hef,min
[mm]
60
60
70
80
90
100
110
120
h = hmin
[mm]
100
100
100
116
138
156
170
190
40
50
60
80
100
120
Edge distance
c = cmin [mm]
Tensile NRd: single anchor, min. edge distance (c = cmin)
Non-cracked concrete
HIT-V 5.8 / 8.8
[kN]
7,1
8,5
9,7
15,4
20,3
25,3
HIT-V-R / -HCR
Cracked concrete
HIT-V 5.8 / 8.8
[kN]
4,7
6,6
12,1
16,4
20,3
HIT-V-R / -HCR
Shear VRd: single anchor, min. edge distance (c = cmin), without lever arm
Non-cracked concrete
HIT-V 5.8 / 8.8
[kN]
3,5
4,9
6,6
10,2
14,1
18,3
HIT-V-R / -HCR
Cracked concrete
HIT-V 5.8 / 8.8
[kN]
3,5
4,7
7,2
10,0
12,9
HIT-V-R / -HCR
135
150
29,4
28,9
21,8
25,9
Embedment depth
Base material thickness
512
6 / 2010
M10
M12
M16
M20
M24
M27
M30
hef = hef,min
[mm]
60
60
70
80
90
100
110
120
h = hmin
[mm]
100
100
100
116
138
156
170
190
40
50
60
80
100
120
135
s = smin [mm]
Tensile NRd: double anchor, no edge effects, min. spacing (s = smin)
Non-cracked concrete
HIT-V 5.8 / 8.8
[kN]
7,4
8,2
10,0
15,1
18,7
22,5
26,0
HIT-V-R / -HCR
Cracked concrete
HIT-V 5.8 / 8.8
[kN]
4,9
6,7
10,7
13,3
16,0
HIT-V-R / -HCR
Shear VRd: double anchor, no edge effects, min. spacing (s = smin), without lever arm
Non-cracked concrete
HIT-V 5.8
[kN]
7,2
12,0
16,8
31,2
39,4
47,1
54,7
HIT-V 8.8
[kN]
12,0
18,4
25,4
32,1
39,4
47,1
54,7
HIT-V-R
[kN]
8,3
12,8
19,2
32,1
39,4
47,1
48,3
HIT-V-HCR
[kN]
12,0
18,4
25,4
32,1
39,4
47,1
54,7
Cracked concrete
150
Embedment depth
Base material thickness
Spacing
M8
[kN]
8,8
12,4
21,4
28,1
33,6
25,0
62,7
62,7
58,8
62,7
hef = hef,typ
[mm]
M8
M10
M12
M16
M20
M24
M27
M30
80
90
110
125
170
210
240
270
218
266
300
340
74,6
74,6
74,6
74,6
102,5
102,5
102,5
102,5
125,2
125,2
80,4
125,2
120,2
120,2
98,3
120,2
42,7
63,3
48,8
78,4
55,1
78,4
70,4
112,8
79,5
70,9
92,0
147,2
48,3
92,0
112,0
179,2
58,8
112,0
48,8
78,4
55,1
78,4
70,4
112,8
79,5
70,9
110
120
140
161
Base material thickness h = hmin [mm]
Tensile NRd: single anchor, no edge effects
Non-cracked concrete
HIT-V 5.8
[kN]
12,0
19,3
28,0
47,1
HIT-V 8.8
[kN]
15,6
22,0
32,3
47,1
HIT-V-R
[kN]
13,9
21,9
31,6
47,1
HIT-V-HCR
[kN]
15,6
22,0
32,3
47,1
Cracked concrete
HIT-V 5.8 / 8.8
[kN]
10,4
15,2
25,1
HIT-V-R / -HCR
Shear VRd: single anchor, no edge effects, without lever arm
Non-cracked concrete
HIT-V 5.8
[kN]
7,2
12,0
16,8
31,2
HIT-V 8.8
[kN]
12,0
18,4
27,2
50,4
HIT-V-R
[kN]
8,3
12,8
19,2
35,3
HIT-V-HCR
[kN]
12,0
18,4
27,2
50,4
Cracked concrete
HIT-V 5.8
[kN]
12,0
16,8
31,2
HIT-V 8.8
[kN]
18,4
27,2
50,3
HIT-V-R
[kN]
12,8
19,2
35,3
HIT-V-HCR
[kN]
18,4
27,2
50,3
6 / 2010
513
M8
M10
M12
M16
M20
M24
M27
M30
hef = hef,typ
[mm]
80
90
110
125
170
210
240
270
h = hmin
[mm]
110
120
140
161
218
266
300
340
40
50
60
80
100
120
Edge distance
c = cmin [mm]
Tensile NRd: single anchor, min. edge distance (c = cmin)
Non-cracked concrete
HIT-V 5.8 / 8.8
[kN]
8,6
11,6
15,5
23,7
36,6
49,8
HIT-V-R / -HCR
Cracked concrete
HIT-V 5.8 / 8.8
[kN]
5,8
8,4
14,8
24,4
36,9
HIT-V-R / -HCR
Shear VRd: single anchor, min. edge distance (c = cmin) , without lever arm
Non-cracked concrete
HIT-V 5.8 / 8.8
[kN]
3,7
5,3
7,3
11,5
17,2
23,6
HIT-V-R / -HCR
Cracked concrete
135
150
60,6
60,0
29,0
34,8
Embedment depth
Base material thickness
[kN]
3,8
5,2
8,1
12,2
16,7
514
M8
M10
M12
M16
M20
M24
M27
M30
hef = hef,typ
[mm]
80
90
110
125
170
210
240
270
h = hmin
[mm]
110
120
140
161
218
266
300
340
40
50
60
80
100
120
135
s [mm]
Tensile NRd: double anchor, no edge effects, min. spacing (s = smin)
Non-cracked concrete
HIT-V 5.8 / 8.8
[kN]
9,9
13,4
18,1
26,9
42,2
57,7
70,4
HIT-V-R / -HCR
Cracked concrete
HIT-V 5.8 / 8.8
[kN]
7,1
10,3
16,5
27,3
39,9
HIT-V-R / -HCR
Shear VRd: double anchor, no edge effects, min. spacing (s = smin), without lever arm
Non-cracked concrete
HIT-V 5.8
[kN]
7,2
12,0
16,8
31,2
48,8
70,4
92,0
HIT-V 8.8
[kN]
12,0
18,4
27,2
50,4
78,4
112,8
147,2
HIT-V-R
[kN]
8,3
12,8
19,2
35,3
55,1
79,5
48,3
HIT-V-HCR
[kN]
12,0
18,4
27,2
50,4
78,4
70,9
92,0
Cracked concrete
HIT-V 5.8
[kN]
12,0
16,8
30,5
48,8
70,4
HIT-V 8.8
[kN]
12,3
18,0
30,5
51,1
75,4
HIT-V-R
[kN]
12,3
18,0
30,5
51,1
75,4
HIT-V-HCR
[kN]
12,3
18,0
30,5
51,1
70,9
-
150
69,9
112,0
170,9
58,8
112,0
-
6 / 2010
hef = 12 d
a)
[mm]
[mm]
M8
96
M10
120
M12
144
M16
192
126
150
174
228
Base material thickness h = hmin
Tensile NRd: single anchor, no edge effects
Non-cracked concrete
HIT-V 5.8
[kN]
12,0
19,3
28,0
52,7
HIT-V 8.8
[kN]
18,8
29,3
42,2
83,6
HIT-V-R
[kN]
13,9
21,9
31,6
58,8
HIT-V-HCR
[kN]
18,8
29,3
42,2
83,6
Cracked concrete
HIT-V 5.8 / 8.8
[kN]
13,8
19,9
38,6
HIT-V-R / -HCR
Shear VRd: single anchor, no edge effects, without lever arm
Non-cracked concrete
HIT-V 5.8
[kN]
7,2
12,0
16,8
31,2
HIT-V 8.8
[kN]
12,0
18,4
27,2
50,4
HIT-V-R
[kN]
8,3
12,8
19,2
35,3
HIT-V-HCR
[kN]
12,0
18,4
27,2
50,4
Cracked concrete
HIT-V 5.8
[kN]
12,0
16,8
31,2
HIT-V 8.8
[kN]
18,4
27,2
50,4
HIT-V-R
[kN]
12,8
19,2
35,3
HIT-V-HCR
[kN]
18,4
27,2
50,4
a) d = element diameter
M20
240
M24
288
M27
324
M30
360
288
344
384
430
82,0
120,6
92,0
120,6
118,0
159,2
132,1
117,6
153,3
183,2
80,4
152,9
160,2
160,2
98,3
160,2
60,3
86,9
48,8
78,4
55,1
78,4
70,4
112,8
79,5
70,9
92,0
147,2
48,3
92,0
112,0
179,2
58,8
112,0
48,8
78,4
55,1
78,4
70,4
112,8
79,5
70,9
M8
M10
M12
M16
M20
M24
M27
M30
[mm]
96
120
144
192
240
288
324
360
[mm]
126
150
174
228
288
344
384
430
40
50
60
80
100
120
Edge distance
c = cmin [mm]
Tensile NRd: single anchor, min. edge distance (c = cmin)
Non-cracked concrete
HIT-V 5.8
[kN]
10,4
16,2
21,7
40,1
56,0
73,6
HIT-V 8.8
[kN]
10,4
16,2
21,7
40,1
56,0
73,6
HIT-V-R
[kN]
10,4
16,2
21,7
40,1
56,0
73,6
HIT-V-HCR
[kN]
10,4
16,2
21,7
40,1
56,0
73,6
Cracked concrete
HIT-V 5.8 / 8.8
[kN]
7,6
11,0
21,7
34,4
50,6
HIT-V-R / -HCR
Shear VRd: single anchor, min. edge distance (c = cmin) , without lever arm
Non-cracked concrete
HIT-V 5.8 / 8.8
[kN]
3,9
5,7
7,8
12,9
18,9
25,9
HIT-V-R / -HCR
Cracked concrete
HIT-V 5.8 / 8.8
[kN]
4,0
5,5
9,1
13,4
18,4
HIT-V-R / -HCR
a) d = element diameter
135
150
87,8
87,8
80,4
87,8
85,7
85,7
85,7
85,7
31,8
38,1
Embedment depth
hef = 12 d a)
6 / 2010
h = hmin
515
hef = 12 d a)
h = hmin
[mm]
M8
96
M10
120
M12
144
M16
192
M20
240
M24
288
M27
324
M30
360
[mm]
126
150
174
228
288
344
384
430
40
50
60
80
100
120
135
s=smin [mm]
Tensile NRd: double anchor, no edge effects, min. spacing (s = smin)
Non-cracked concrete
HIT-V 5.8
[kN]
12,0
18,5
26,0
48,9
68,4
89,9
107,2
HIT-V 8.8
[kN]
12,1
18,5
26,0
48,9
68,4
89,9
107,2
HIT-V-R
[kN]
12,1
18,5
26,0
48,9
68,4
89,9
80,4
HIT-V-HCR
[kN]
12,1
18,5
26,0
48,9
68,4
89,9
107,2
Cracked concrete
HIT-V 5.8 / 8.8
[kN]
9,6
13,6
25,8
39,8
56,7
HIT-V-R / -HCR
Shear VRd: double anchor, no edge effects, min. spacing (s = smin) , without lever arm
Non-cracked concrete
HIT-V 5.8
[kN]
7,2
12,0
16,8
31,2
48,8
70,4
92,0
HIT-V 8.8
[kN]
12,0
18,4
27,2
50,4
78,4
112,8
147,2
HIT-V-R
[kN]
8,3
12,8
19,2
35,3
55,1
79,5
48,3
HIT-V-HCR
[kN]
12,0
18,4
27,2
50,4
78,4
70,9
92,0
Cracked concrete
HIT-V 5.8
[kN]
12,0
16,8
31,2
48,8
70,4
HIT-V 8.8
[kN]
15,7
22,7
44,0
68,7
98,9
HIT-V-R
[kN]
12,8
19,2
35,3
55,1
79,5
HIT-V-HCR
[kN]
15,7
22,7
44,0
68,7
70,9
a) d = element diameter
Spacing
516
150
103,8
103,8
98,3
103,8
-
112,0
179,2
58,8
112,0
-
6 / 2010
hef = hef,min
[mm]
M8
M10
M12
M16
M20
M24
M27
M30
60
60
70
80
90
100
110
120
138
156
170
190
20,5
24,1
27,7
26,4
14,6
17,1
34,9
41,1
39,4
41,1
48,1
48,1
48,1
48,1
55,5
55,5
34,5
55,5
63,2
63,2
42,0
63,2
29,3
29,3
29,3
29,3
34,3
34,3
34,3
34,3
100
100
100
116
Base material thickness h = hmin [mm]
Tensile Nrec: single anchor, no edge effects
Non-cracked concrete
HIT-V 5.8 / 8.8
[kN]
8,4
9,3
11,7
17,2
HIT-V-R / -HCR
Cracked concrete
HIT-V 5.8 / 8.8
[kN]
4,9
6,9
11,5
HIT-V-R / -HCR
Shear Vrec: single anchor, no edge effects, without lever arm
Non-cracked concrete
HIT-V 5.8
[kN]
5,1
8,6
12,0
22,3
HIT-V 8.8
[kN]
8,6
13,1
19,4
34,4
HIT-V-R
[kN]
5,9
9,1
13,7
25,2
HIT-V-HCR
[kN]
8,6
13,1
19,4
34,4
Cracked concrete
HIT-V 5.8
[kN]
8,6
12,0
22,3
HIT-V 8.8
[kN]
9,9
13,9
23,0
HIT-V-R
[kN]
9,1
13,7
23,0
HIT-V-HCR
[kN]
9,9
13,9
23,0
M8
M10
M12
M16
M20
M24
M27
M30
hef = hef,min
[mm]
60
60
70
80
90
100
110
120
h = hmin
[mm]
100
100
100
116
138
156
170
190
40
50
60
80
100
120
Edge distance
c = cmin [mm]
Tensile Nrec: single anchor, min. edge distance (c = cmin)
Non-cracked concrete
HIT-V 5.8 / 8.8
[kN]
5,1
6,1
6,9
11,0
14,5
18,1
HIT-V-R / -HCR
Cracked concrete
HIT-V 5.8 / 8.8
[kN]
3,4
4,7
8,6
11,7
14,5
HIT-V-R / -HCR
Shear Vrec: single anchor, min. edge distance (c = cmin), without lever arm
Non-cracked concrete
HIT-V 5.8 / 8.8
[kN]
2,5
3,5
4,7
7,3
10,1
13,1
HIT-V-R / -HCR
Cracked concrete
HIT-V 5.8 / 8.8
[kN]
2,5
3,4
5,1
7,1
9,2
HIT-V-R / -HCR
135
150
21,0
20,6
15,6
18,5
Embedment depth
Base material thickness
6 / 2010
517
M10
M12
M16
M20
M24
M27
M30
hef = hef,min
[mm]
60
60
70
80
90
100
110
120
h = hmin
[mm]
100
100
100
116
138
156
170
190
40
50
60
80
100
120
135
s = smin [mm]
Tensile Nrec: double anchor, no edge effects, min. spacing (s = smin)
Non-cracked concrete
HIT-V 5.8 / 8.8
[kN]
5,3
5,9
7,1
10,8
13,4
16,1
18,6
HIT-V-R / -HCR
Cracked concrete
HIT-V 5.8 / 8.8
[kN]
3,5
4,8
7,6
9,5
11,4
HIT-V-R / -HCR
Shear Vrec: double anchor, no edge effects, min. spacing (s = smin), without lever arm
Non-cracked concrete
HIT-V 5.8
[kN]
5,1
8,6
12,0
22,3
28,1
33,6
39,1
HIT-V 8.8
[kN]
8,6
13,1
18,1
22,9
28,1
33,6
39,1
HIT-V-R
[kN]
5,9
9,1
13,7
22,9
28,1
33,6
34,5
HIT-V-HCR
[kN]
8,6
13,1
18,1
22,9
28,1
33,6
39,1
Cracked concrete
HIT-V 5.8 / 8.8
[kN]
6,3
8,9
15,3
20,1
24,0
HIT-V-R / -HCR
150
Embedment depth
Base material thickness
Spacing
M8
17,9
44,8
44,8
42,0
44,8
-
For the recommended loads an overall partial safety factor for action = 1,4 is considered. The partial safety
factors for action depend on the type of loading and shall be taken from national regulations. According ETAG 001,
annex C, the partial safety factor is G = 1,35 for permanent actions and Q = 1,5 for variable actions.
hef = hef,typ
[mm]
M8
M10
M12
M16
M20
M24
M27
M30
80
90
110
125
170
210
240
270
218
266
300
340
53,3
53,3
53,3
53,3
73,2
73,2
73,2
73,2
89,4
89,4
57,4
89,4
85,9
85,9
70,2
85,9
30,5
45,2
34,9
56,0
39,4
56,0
50,3
80,6
56,8
50,6
65,7
105,1
34,5
65,7
80,0
128,0
42,0
80,0
34,9
56,0
39,4
56,0
50,3
80,6
56,8
50,6
110
120
140
161
Base material thickness h = hmin [mm]
Tensile Nrec: single anchor, no edge effects
Non-cracked concrete
HIT-V 5.8
[kN]
8,6
13,8
20,0
33,6
HIT-V 8.8
[kN]
11,1
15,7
23,1
33,6
HIT-V-R
[kN]
9,9
15,6
22,6
33,6
HIT-V-HCR
[kN]
11,1
15,7
23,1
33,6
Cracked concrete
HIT-V 5.8 / 8.8
[kN]
7,4
10,9
17,9
HIT-V-R / -HCR
Shear Vrec: single anchor, no edge effects, without lever arm
Non-cracked concrete
HIT-V 5.8
[kN]
5,1
8,6
12,0
22,3
HIT-V 8.8
[kN]
8,6
13,1
19,4
36,0
HIT-V-R
[kN]
5,9
9,1
13,7
25,2
HIT-V-HCR
[kN]
8,6
13,1
19,4
36,0
Cracked concrete
HIT-V 5.8
[kN]
8,6
12,0
22,3
HIT-V 8.8
[kN]
13,1
19,4
35,9
HIT-V-R
[kN]
9,1
13,7
25,2
HIT-V-HCR
[kN]
13,1
19,4
35,9
518
6 / 2010
M8
M10
M12
M16
M20
M24
M27
M30
hef = hef,typ
[mm]
80
90
110
125
170
210
240
270
h = hmin
[mm]
110
120
140
161
218
266
300
340
40
50
60
80
100
120
Edge distance
c = cmin [mm]
Tensile Nrec: single anchor, min. edge distance (c = cmin)
Non-cracked concrete
HIT-V 5.8 / 8.8
[kN]
6,1
8,3
11,1
16,9
26,1
35,6
HIT-V-R / -HCR
Cracked concrete
HIT-V 5.8 / 8.8
[kN]
4,1
6,0
10,6
17,4
26,4
HIT-V-R / -HCR
Shear Vrec: single anchor, min. edge distance (c = cmin) , without lever arm
Non-cracked concrete
HIT-V 5.8 / 8.8
[kN]
2,6
3,8
5,2
8,2
12,3
16,9
HIT-V-R / -HCR
Cracked concrete
HIT-V 5.8 / 8.8
[kN]
2,7
3,7
5,8
8,7
11,9
HIT-V-R / -HCR
135
150
43,3
42,9
20,7
24,9
Embedment depth
Base material thickness
M8
M10
M12
M16
M20
M24
M27
M30
hef = hef,typ
[mm]
80
90
110
125
170
210
240
270
h = hmin
[mm]
110
120
140
161
218
266
300
340
[mm]
40
50
60
80
100
120
135
150
49,9
80,0
122,1
42,0
80,0
-
For the recommended loads an overall partial safety factor for action = 1,4 is considered. The partial safety
factors for action depend on the type of loading and shall be taken from national regulations. According ETAG 001,
annex C, the partial safety factor is G = 1,35 for permanent actions and Q = 1,5 for variable actions.
6 / 2010
519
hef = 12 d
a)
[mm]
[mm]
M8
96
M10
120
M12
144
M16
192
126
150
174
228
Base material thickness h = hmin
Tensile Nrec: single anchor, no edge effects
Non-cracked concrete
HIT-V 5.8
[kN]
8,6
13,8
20,0
37,6
HIT-V 8.8
[kN]
13,4
20,9
30,1
59,7
HIT-V-R
[kN]
9,9
15,6
22,6
42,0
HIT-V-HCR
[kN]
13,4
20,9
30,1
59,7
Cracked concrete
HIT-V 5.8 / 8.8
[kN]
9,9
14,2
27,6
HIT-V-R / -HCR
Shear Vrec: single anchor, no edge effects, without lever arm
Non-cracked concrete
HIT-V 5.8
[kN]
5,1
8,6
12,0
22,3
HIT-V 8.8
[kN]
8,6
13,1
19,4
36,0
HIT-V-R
[kN]
5,9
9,1
13,7
25,2
HIT-V-HCR
[kN]
8,6
13,1
19,4
36,0
Cracked concrete
HIT-V 5.8
[kN]
8,6
12,0
22,3
HIT-V 8.8
[kN]
13,1
19,4
36,0
HIT-V-R
[kN]
9,1
13,7
25,2
HIT-V-HCR
[kN]
13,1
19,4
36,0
a) d = element diameter
M20
240
M24
288
M27
324
M30
360
288
344
384
430
58,6
86,1
65,7
86,1
84,3
113,7
94,4
84,0
109,5
130,9
57,4
109,2
114,4
114,4
70,2
114,4
43,1
62,1
34,9
56,0
39,4
56,0
50,3
80,6
56,8
50,6
65,7
105,1
34,5
65,7
80,0
128,0
42,0
80,0
34,9
56,0
39,4
56,0
50,3
80,6
56,8
50,6
M8
M10
M12
M16
M20
M24
M27
M30
[mm]
96
120
144
192
240
288
324
360
[mm]
126
150
174
228
288
344
384
430
40
50
60
80
100
120
Edge distance
c = cmin [mm]
Tensile Nrec: single anchor, min. edge distance (c = cmin)
Non-cracked concrete
HIT-V 5.8
[kN]
7,4
11,6
15,5
28,6
40,0
52,6
HIT-V 8.8
[kN]
7,4
11,6
15,5
28,6
40,0
52,6
HIT-V-R
[kN]
7,4
11,6
15,5
28,6
40,0
52,6
HIT-V-HCR
[kN]
7,4
11,6
15,5
28,6
40,0
52,6
Cracked concrete
HIT-V 5.8 / 8.8
[kN]
5,4
7,9
15,5
24,6
36,1
HIT-V-R / -HCR
Shear Vrec: single anchor, min. edge distance (c = cmin) , without lever arm
Non-cracked concrete
HIT-V 5.8 / 8.8
[kN]
2,8
4,1
5,6
9,2
13,5
18,5
HIT-V-R / -HCR
Cracked concrete
HIT-V 5.8 / 8.8
[kN]
2,9
3,9
6,5
9,6
13,1
HIT-V-R / -HCR
a) d = element diameter
135
150
62,7
62,7
57,4
62,7
61,2
61,2
61,2
61,2
22,7
27,2
Embedment depth
hef = 12 d a)
520
h = hmin
6 / 2010
hef = 12 d a)
h = hmin
[mm]
M8
96
M10
120
M12
144
M16
192
M20
240
M24
288
M27
324
M30
360
[mm]
126
150
174
228
288
344
384
430
40
50
60
80
100
120
135
s=smin [mm]
Tensile Nrec: double anchor, no edge effects, min. spacing (s = smin)
Non-cracked concrete
HIT-V 5.8
[kN]
8,6
13,2
18,6
34,9
48,9
64,2
76,6
HIT-V 8.8
[kN]
8,6
13,2
18,6
34,9
48,9
64,2
76,6
HIT-V-R
[kN]
8,6
13,2
18,6
34,9
48,9
64,2
57,4
HIT-V-HCR
[kN]
8,6
13,2
18,6
34,9
48,9
64,2
76,6
Cracked concrete
HIT-V 5.8 / 8.8
[kN]
6,9
9,7
18,4
28,4
40,5
HIT-V-R / -HCR
Shear Vrec: double anchor, no edge effects, min. spacing (s = smin) , without lever arm
Non-cracked concrete
HIT-V 5.8
[kN]
5,1
8,6
12,0
22,3
34,9
50,3
65,7
HIT-V 8.8
[kN]
8,6
13,1
19,4
36,0
56,0
80,6
105,1
HIT-V-R
[kN]
5,9
9,1
13,7
25,2
39,4
56,8
34,5
HIT-V-HCR
[kN]
8,6
13,1
19,4
36,0
56,0
50,6
65,7
Cracked concrete
HIT-V 5.8
[kN]
8,6
12,0
22,3
34,9
50,3
HIT-V 8.8
[kN]
11,2
16,2
31,4
49,1
70,6
HIT-V-R
[kN]
9,1
13,7
25,2
39,4
56,8
HIT-V-HCR
[kN]
11,2
16,2
31,4
49,1
50,6
a) d = element diameter
Spacing
150
74,1
74,1
70,2
74,1
-
80,0
128,0
42,0
80,0
-
For the recommended loads an overall partial safety factor for action = 1,4 is considered. The partial safety
factors for action depend on the type of loading and shall be taken from national regulations. According ETAG 001,
annex C, the partial safety factor is G = 1,35 for permanent actions and Q = 1,5 for variable actions.
6 / 2010
521
Benefits
Hilti HITHY 150 MAX
330 ml foil pack
(also available
as 500 ml
and 1400 ml
foil pack)
Static mixer
Internal
threaded sleeve
HIS-N
HIS-RN
Concrete
Small edge
distance
and spacing
Corrosion
resistance
European
Technical
Approval
CE
conformity
Hilti anchor
design
software
Approvals / certificates
Description
European technical approval
a)
Authority / Laboratory
DIBt, Berlin
522
6 / 2010
Embedment depth and base material thickness for the basic loading data.
Mean ultimate resistance, characteristic resistance, design resistance, recommended loads.
Anchor size
M8x90
M10x110
M12x125
M16x170
Embedment depth
hef [mm]
90
110
125
170
Base material thickness h [mm]
120
150
170
230
M20x205
205
270
HIS-N
[kN]
M8x90
26,3
Shear VRu,m
HIS-N
[kN]
13,7
M10x110
48,3
M12x125
70,4
M16x170
123,9
M20x205
114,5
24,2
41,0
62,0
57,8
M8x90
M10x110
M12x125
M16x170
M20x205
46,0
67,0
95,0
109,0
23,0
39,0
59,0
55,0
Tensile NRk
HIS-N
[kN]
25,0
Shear VRk
HIS-N
[kN]
13,0
M8x90
M10x110
M12x125
M16x170
M20x205
Tensile NRd
HIS-N
[kN]
17,5
26,7
40,0
62,2
74,1
Shear VRd
HIS-N
[kN]
10,4
18,4
26,0
39,3
36,7
M8x90
M10x110
M12x125
M16x170
M20x205
Tensile Nrec
HIS-N
[kN]
12,5
19,8
31,9
45,2
53,0
Shear Vrec
HIS-N
[kN]
7,4
13,1
18,6
28,1
26,2
a) With overall partial safety factor for action = 1,4. The partial safety factors for action depend on the type of
loading and shall be taken from national regulations. According ETAG 001, annex C, the partial safety factor is
G = 1,35 for permanent actions and Q = 1,5 for variable actions.
Temperature range
Temperature range I
Temperature range II
Temperature range III
Base material
temperature
-40 C to +40 C
-40 C to +80 C
-40 C to +120 C
6 / 2010
523
Materials
Mechanical properties of HIS-(R)N
Anchor size
Nominal
tensile
strength f uk
Yield
strength fyk
Stressed
crosssection As
HIS-N
[N/mm]
M8x90
490
M10x110
490
M12x125
460
M16x170
460
M20x205
460
Screw 8.8
[N/mm]
800
800
800
800
800
HIS-RN
[N/mm]
700
700
700
700
700
Screw A4-70
[N/mm]
700
700
700
700
700
HIS-N
[N/mm]
410
410
375
375
375
Screw 8.8
[N/mm]
640
640
640
640
640
HIS-RN
[N/mm]
350
350
350
350
350
Screw A4-70
[N/mm]
450
450
450
450
450
HIS-(R)N
[mm]
51,5
108,0
169,1
256,1
237,6
Screw
[mm]
36,6
58
84,3
157
245
[mm]
145
430
840
1595
1543
[mm]
31,2
62,3
109
277
541
HIS-(R)N
Moment of
resistance W Screw
Material quality
Part
Internal threaded sleeve
HIS-N
Material
C-steel 1.0718, EN 10277-3
Steel galvanized 5m EN ISO 4042
a)
related fastening screw: strength class 8.8 EN ISO 898-1, A5 > 8% Ductile
steel galvanized 5m EN ISO 4042
related fastening screw: strength class 70 EN ISO 3506-1, A5 > 8% Ductile
stainless steel 1.4401; 1.4404; 1.4578; 1.4571; 1.4439; 1.4362 EN 10088
Anchor dimensions
Anchor size
Internal threaded sleeve
HIS-N / HIS-RN
Embedment depth
hef
[mm]
M8x90
M10x110
M12x125
M16x170
M20x205
80
90
110
125
170
Setting
installation equipment
Anchor size
Rotary hammer
Other tools
524
M8x90
M10x110
M12x125
M16x170
M20x205
TE 2 TE 16
TE 40 TE 70
compressed air gun or blow out pump, set of cleaning brushes, dispenser
6 / 2010
Setting instruction
Dry and water-saturated concrete, hammer drilling
a)
b)
6 / 2010
525
Curing time
tcure
12 h
4 h
2 h
1 h
30 min
30 min
Working time
tgel
180 min
40 min
20 min
8 min
5 min
2 min
-5 C
0 C
5 C
20 C
30 C
40 C
Setting details
df
d0
hS
526
6 / 2010
Anchor size
Nominal diameter of
drill bit
Diameter of element
Effective anchorage
and drill hole depth
Minimum base
material thickness
Diameter of clearance
hole in the fixture
Thread engagement
length; min - max
Torque moment a)
Minimum spacing
Minimum edge
distance
Critical spacing
for splitting failure
M8x90
M10x110
M12x125
M16x170
M20x205
d0
[mm]
14
18
22
28
32
[mm]
12,5
16,5
20,5
25,4
27,6
hef
[mm]
90
110
125
170
205
hmin
[mm]
120
150
170
230
270
df
[mm]
12
14
18
22
hs
[mm]
8-20
10-25
12-30
16-40
20-50
Tmax
[Nm]
10
20
40
80
150
smin
[mm]
40
45
55
65
90
cmin
[mm]
40
45
55
65
90
scr,sp
[mm]
ccr,sp
[mm]
2 ccr,sp
1,0 hef
2,26 hef
scr,N
[mm]
2 ccr,N
ccr,N
[mm]
1,5 hef
For spacing (or edge distance) smaller than critical spacing (or critical edge distance) the design loads have to be
reduced.
a)
Maximum recommended torque moment to avoid splitting failure during installation with minimum spacing
and/or edge distance.
b)
c)
The critical edge distance for concrete cone failure depends on the embedment depth hef and the design bond
resistance. The simplified formula given in this table is on the save side.
6 / 2010
527
TENSION loading
The design tensile resistance is the lower value of
- Steel resistance:
NRd,s
[kN]
[kN]
M8x90
17,5
13,9
M10x110
30,7
21,9
M12x125
44,7
31,6
M16x170
80,3
58,8
M20x205
74,1
69,2
M16x170
170
63,3
63,3
40,0
M20x205
205
76,7
63,3
40,0
528
M8x90
90
19,4
16,7
11,1
M10x110
110
27,8
27,8
16,7
M12x125
125
50,0
40,0
26,7
6 / 2010
Design concrete cone resistance NRd,c = N0Rd,c fB f1,N f2,N f3,N fh,N fre,N
Design splitting resistance a) NRd,sp = N0Rd,c fB f1,sp f2,sp f3,sp f h,N fre,N
Anchor size
N0Rd,c
M8
24,0
[kN]
M10
32,4
M12
47,1
M16
74,6
M20
98,8
Influencing factors
Influence of concrete strength on combined pull-out and concrete cone resistance
Concrete strength designation
(ENV 206)
C 20/25
C 25/30
C 30/37
C 35/45
C 40/50
0,10 a)
1,00
1,02
1,04
1,06
1,07
f B,p = (f ck,cube/25N/mm)
a) fck,cube = concrete compressive strength, measured on cubes with 150 mm side length
C 45/55
C 50/60
1,08
1,09
C 20/25
C 25/30
C 30/37
C 35/45
C 40/50
0,5 a)
fB =
(f ck,cube/25N/mm)
1
1,1
1,22
1,34
1,41
a) fck,cube = concrete compressive strength, measured on cubes with 150 mm side length
C 45/55
C 50/60
1,48
1,55
0,7 + 0,3c/ccr,N 1
0,1
0,2
0,3
0,4
0,5
0,6
0,7
0,8
0,9
0,73
0,76
0,79
0,82
0,85
0,88
0,91
0,94
0,97
0,5(1 + c/ccr,N) 1
0,1
s/scr,sp
f 3,N =
0,2
0,3
0,4
0,5
0,6
0,7
0,8
0,9
0,5(1 + s/scr,N) 1
6 / 2010
529
Influence of reinforcement
hef [mm]
40
50
60
70
80
90
100
a)
a)
a)
a)
a)
a)
0,7
0,75
0,8
0,85
0,9
0,95
1
f re,N = 0,5 + hef/200mm 1
a) This factor applies only for dense reinforcement. If in the area of anchorage there is reinforcement with a
spacing 150 mm (any diameter) or with a diameter 10 mm and a spacing 100 mm, then a factor fre,N = 1
may be applied.
SHEAR loading
The design shear resistance is the lower value of
- Steel resistance:
-
VRd,s
VRd,cp = k lower value of NRd,p and NRd,c
0
Rd,c
VRd,c = V
fB f f h f4 f hef fc
[kN]
[kN]
M8x90
10,4
8,3
M10x110
18,4
12,8
M12x125
26,0
19,2
M16x170
39,3
35,3
M20x205
36,7
41,5
Design concrete pryout resistance VRd,cp = lower valuea) of k NRd,p and k NRd,c
k = 2 for hef 60 mm
a)
[kN]
= V0Rd,c fB f f h f4 f hef fc
M8
M10
M12
M16
M20
12,4
19,6
28,2
40,2
46,2
Influencing factors
Influence of concrete strength
Concrete strength designation
(ENV 206)
C 20/25
C 25/30
C 30/37
C 35/45
C 40/50
fB =
(f ck,cube/25N/mm)1/2 a)
1
1,1
1,22
1,34
1,41
a) fck,cube = concrete compressive strength, measured on cubes with 150 mm side length
530
C 45/55
C 50/60
1,48
1,55
6 / 2010
Influence of angle between load applied and the direction perpendicular to the free edge
Angle
10
20
30
40
50
60
70
80
90
1,01
1,05
1,13
1,24
1,40
1,64
1,97
2,32
2,50
0,15
0,3
0,45
0,6
0,75
0,9
1,05
1,2
1,35
1,5
0,32
0,45
0,55
0,63
0,71
0,77
0,84
0,89
0,95
1,00
{h/(1,5 c)}
1/2
Influence of anchor spacing and edge distance a) for concrete edge resistance: f4
f4 = (c/hef)1,5 (1 + s / [3 c]) 0,5
Single
anchor 0,75 1,50
0,50
0,35
0,27 0,35
0,75
0,65
0,43 0,54
1,00
1,00
0,63 0,75
1,25
1,40
0,84 0,98
1,50
1,84
1,07 1,22
1,75
2,32
1,32 1,49
2,00
2,83
1,59 1,77
2,25
3,38
1,88 2,06
2,50
3,95
2,17 2,37
2,75
4,56
2,49 2,69
3,00
5,20
2,81 3,03
3,25
5,86
3,15 3,38
3,50
6,55
3,51 3,74
3,75
7,26
3,87 4,12
4,00
8,00
4,25 4,50
4,25
8,76
4,64 4,90
4,50
9,55
5,04 5,30
4,75
10,35 5,45 5,72
5,00
11,18 5,87 6,15
5,25
12,03 6,30 6,59
5,50
12,90 6,74 7,04
a) The anchor spacing and the
minimum edge distance cmin.
c/hef
10,50 11,25
0,35 0,35
0,65 0,65
1,00 1,00
1,40 1,40
1,84 1,84
2,32 2,32
2,83 2,83
3,38 3,38
3,95 3,95
4,56 4,56
5,20 5,20
5,86 5,86
6,55 6,55
7,02 7,26
7,50 7,75
7,99 8,25
8,49 8,75
8,99 9,26
9,50 9,78
10,02 10,31
10,55 10,85
smin and the
M8
M10
M12
M16
M20
f hef =
1,38
1,21
1,04
1,22
1,45
c/d
0,19
10
15
0,77
0,71
0,67
0,65
0,60
fc =
(d / c)
a) The edge distance shall not be smaller than the minimum edge distance cmin.
6 / 2010
20
30
40
0,57
0,52
0,50
531
M8x90
M10x110
M12x125
M16x170
M20x205
90
110
125
170
205
120
150
Base material thickness h = hmin [mm]
Tensile NRd: single anchor, no edge effects
170
230
270
Embedment depth
hef
[mm]
HIS-N
[kN]
17,5
27,8
44,7
63,3
74,1
HIS-RN
[kN]
13,9
21,9
31,6
58,8
69,2
[kN]
10,4
18,4
26,0
39,3
36,7
HIS-RN
[kN]
8,3
12,8
19,2
35,3
41,5
M8x90
M10x110
M12x125
M16x170
M20x205
hef
[mm]
90
110
125
170
205
h = hmin
[mm]
120
150
170
230
270
55
65
90
40
45
Edge distance
c = cmin [mm]
Tensile NRd: single anchor, min. edge distance (c = cmin)
HIS-N
[kN]
9,9
13,8
21,6
31,2
41,7
HIS-RN
[kN]
9,9
13,8
21,6
31,2
41,7
Shear VRd: single anchor, min. edge distance (c = cmin), without lever arm
HIS-N
[kN]
4,2
5,5
7,6
10,8
17,2
HIS-RN
[kN]
4,2
5,5
7,6
10,8
17,2
M8x90
M10x110
M12x125
M16x170
M20x205
hef
[mm]
90
110
125
170
205
h = hmin
[mm]
120
150
170
230
270
65
90
40
45
55
s = smin [mm]
Tensile NRd: double anchor, no edge effects, min. spacing (s = smin)
HIS-N
[kN]
11,9
16,6
25,9
37,9
48,4
HIS-RN
[kN]
11,9
16,6
25,9
37,9
48,4
Shear VRd: double anchor, no edge effects, min. spacing (s = smin), without lever arm
532
HIS-N
[kN]
10,4
18,4
26,0
39,3
36,7
HIS-RN
[kN]
8,3
12,8
19,2
35,3
41,5
6 / 2010
M8x90
M10x110
M12x125
M16x170
M20x205
90
110
125
170
205
120
150
Base material thickness h = hmin [mm]
Tensile Nrec: single anchor, no edge effects
170
230
270
Embedment depth
hef
[mm]
HIS-N
[kN]
12,5
19,9
31,9
45,2
52,9
HIS-RN
[kN]
9,9
15,6
22,6
42,0
49,4
[kN]
7,4
13,1
18,6
28,1
26,2
HIS-RN
[kN]
5,9
9,1
13,7
25,2
29,6
M8x90
M10x110
M12x125
M16x170
M20x205
hef
[mm]
90
110
125
170
205
h = hmin
[mm]
120
150
170
230
270
55
65
90
40
45
Edge distance
c = cmin [mm]
Tensile Nrec: single anchor, min. edge distance (c = cmin)
HIS-N
[kN]
7,1
9,9
15,4
22,3
29,8
HIS-RN
[kN]
7,1
9,9
15,4
22,3
29,8
Shear Vrec: single anchor, min. edge distance (c = cmin), without lever arm
HIS-N
[kN]
3,0
3,9
5,4
7,7
12,3
HIS-RN
[kN]
3,0
3,9
5,4
7,7
12,3
M8x90
M10x110
M12x125
M16x170
M20x205
hef
[mm]
90
110
125
170
205
h = hmin
[mm]
120
150
170
230
270
65
90
40
45
55
s = smin [mm]
Tensile Nrec: double anchor, no edge effects, min. spacing (s = smin)
HIS-N
[kN]
8,5
11,9
18,5
27,1
34,6
HIS-RN
[kN]
8,5
11,9
18,5
27,1
34,6
Shear Vrec: double anchor, no edge effects, min. spacing (s = smin), without lever arm
HIS-N
[kN]
7,4
13,1
18,6
28,1
26,2
HIS-RN
[kN]
5,9
9,1
13,7
25,2
29,6
For the recommended loads an overall partial safety factor for action = 1,4 is considered. The partial safety
factors for action depend on the type of loading and shall be taken from national regulations. According ETAG 001,
annex C, the partial safety factor is G = 1,35 for permanent actions and Q = 1,5 for variable actions.
6 / 2010
533