Académique Documents
Professionnel Documents
Culture Documents
Design Criteria A. Design Code CODE : BS 5950-1-2000 B. Service Loads V1 := 5.19 kN Pu := 11.77kN Mu := 27.27 kN m C. Properties C.1 For concrete pedestal: fc := 30MPa D1 := 400mm D2 := 400mm A2 := D1 D2 dae := 50mm C.2 Size of Steel Column: dp := 168.3 mm tw := 7.1 mm C.3 For Steel Base Plate : Fy := 275 MPa For Anchor bolts : Fu := 640 MPa ab := 20mm Ft := 0.75 Fu Anchor bolt ultimate strength Grade 8.8 based on Table 34 BS 5950-1-200 anchor bolt diameter yield strength of steel Fy = 275 MPa diameter of column thickness of column concrete cylinder strength @ 28 days Pedestal Dinension 1 Pedestal Dimension 2 Pedestal Area Anchor rod edge distance on baseplate fc = 30 N mm
2
Shear force on a column Total Compressive column load Total Moment Pu = 1.177 10 N Mu = 2.727 10 N mm
7 4
( ab2)
4
Ft = 150.796 kN
Width of base plate baseplate cantilver projections from the edge area provided Aprov = 9 10 mm
4 2
Aprov := B1
A2 Aprov
, 0.7 fc
fpmax = 21
N mm
2
fpmax = 21 ecrit := B1 6
N mm
2
= 0.05m
echeck := if ( e1 < ecrit , "Use Small Moment Calculation" , "Use large moment calculation" ) echeck = "Use large moment calculation" dbc := B1 dp 2 = 65.85 mm dp
Mu Pu Ts1 := dbc +
2 = 175.197 kN dp 2 = 0.198m
EDGE distance of the plate measured from side of the column Tension on the bolts
As1 := 3
( B1 dp)
2
Bearing length
check := if ( fcb > fpmax , "Increase baseplate Dimension" , "Baseplate dimension is OK" ) check = "Baseplate dimension is OK" Mmaxbb := 0.85 fcb dae B1 = 0.02m 6 Mmaxbb 1.2Fy
2
N mm
2
tbpmax :=
= 19.122 mm
D. 2. Design of base plate with stiffener D.2.1 Design of base plate B1use := 300mm size of base plate used
bs :=
B1use 4
= 212.132 mm
ls := bs
dp 2
= 127.982 mm
rs :=
ls bs
= 0.603
Mu Pu Ts := dbc +
dp
2 = 175.197 kN dp 2 = 197.55 mm
As2 := 3
( B1use dp)
2
Bearing length
fc1 :=
( Ts + Pu)
2As2 B1use
= 1.577
N mm
2
N mm N mm
Moment at the edge Moment at the face of the column thickness of base plate based on Mmax1
tbp1 :=
= 8.486 mm
tbp2 :=
= 10.326 mm
thickness of base plate based on Mmax2 THICKNESS OF BASE PLATE WITH STIFFENER PLATE
D. 2.2. DESIGN OF STIFFENER PLATE Stiffener Plate Properties tgusset := 10mm bgusset := 65mm height of the stiffner plate agusset := 150mm thickness of the gusset plate bottom length of stiffner plate
Calculation for Shear and Moment affecting the plate As3 := As2
( B1use dp)
2
As2 As2 ( B1use dp) fc1 + fc2 ( B1use dp) Fmgusset := B1use 0.6 2 2 2
Fmgusset = 1.231 10 N mm zv := 1.39 2.2
6
+ 0.25
bgusset agusset
= 1.031 10 N mm
spcheck1 := if ( fvgusset > Fvgusset , "plate passed in shear" , "increase dimension" ) spcheck1 = "plate passed in shear" spcheck2 := if ( fmgusset > Fmgusset , "plate passed in moment" , "increase dimension" ) spcheck2 = "plate passed in moment"
sp :=
sp = 100 mm
LAB :=
Ts nbuse
0.7 fc ab
= 208.568 mm
LABBENDmin := 3.5 ab = 70 mm
LABTOT = 392.326 mm
F. SUMMARY Based on the above calculations, we will be using the following sections 1. 4-550mm anchor bolt length with 70mm bend 2. 350x350xx16mm Base Plate with Stffner plate of 150x65x10mm