Académique Documents
Professionnel Documents
Culture Documents
Owner
20.12.2010 DATE
S.K.
DESIGNED BY
A.G.
PREPARED BY
F.E.E.
CHECKED BY
H.G
APPR. BY
Consultant
Project
Unit
H.GUNES
Doc. Sequence No 050 Rev. Code 0
Page 2
of
INDEX
1. 2. 3.
INTRODUCTION .................................................................................................................3 STANDARDS ......................................................................................................................4 CALCULATION ...................................................................................................................5 3.1. 3.2. Tensile Strength of Plate...........................................................................................5 Welding Calculation ....................................................................................................6 CONCLUSION ................................................................................................................8 ATTACHMENTS .............................................................................................................9
4. 5.
MISURATA COMMERTIAL PORT CONTAINER BERTH CATHODIC PROTECTION SYSTEM ANCHOR PLATE CALCULATIONS 0 Date: 20.12.2010
Page 3
of
1. INTRODUCTION
This document includes SS316 Anchor Plate calculations that will be used on MISURATA COMMERTIAL PORT CONTAINER BERTH.
MISURATA COMMERTIAL PORT CONTAINER BERTH CATHODIC PROTECTION SYSTEM ANCHOR PLATE CALCULATIONS 0 Date: 20.12.2010
Page 4
of
2. STANDARDS
AWS A5.9:06 TS EN ISO 14343-A:08 ASTM A240/A240M:09 EN10028-7:08 DIN 4100 TS 3357
MISURATA COMMERTIAL PORT CONTAINER BERTH CATHODIC PROTECTION SYSTEM ANCHOR PLATE CALCULATIONS 0 Date: 20.12.2010
Page 5
of
3. CALCULATION
3.1. Tensile Strength of Plate As a construction material, 8 mm thick EN10028-7/08, WNR 1.4404/1.4401, ASTM A240/A240M-09 type 316 plates will be used. Material certificate is attached to this file.
The critical section for this load at top of the hole is; Area = A = 15 x 8 = 120 mm2 = 1,2 cm2 Load = P = 90 Kg (from MBR-CP-E-S-000-027 Rev.1) Yield Strength = = 205 MPa 2,05 t/cm2 (ASTM A240 A240M Table 2 for SS 316)
MISURATA COMMERTIAL PORT CONTAINER BERTH CATHODIC PROTECTION SYSTEM ANCHOR PLATE CALCULATIONS 0 Date: 20.12.2010
Page 6
of
According to DIN 4100 and TS3357 (Building Code for Design and Execution of Welded Connections) Section 2.2.1.1, welding thickness in fillet weld is; 3 a 0,7 tmin, If thickness of plate is 8 mm then, 3 a 5,6 mm.
MISURATA COMMERTIAL PORT CONTAINER BERTH CATHODIC PROTECTION SYSTEM ANCHOR PLATE CALCULATIONS 0 Date: 20.12.2010
Page 7
of
Yield strength of welding wire is 4,2 t/cm2 (According to AWS A5.9:2006 and TS EN ISO 14343 A:8 and material certificate attached to this file) 0,013 t/cm2 < 4,2 t/cm2 O.K.
According to assumed welding area, calculated yield strength is much smaller than that of filler material. Because of that, there is no need to make further calculations for complete welding area.
MISURATA COMMERTIAL PORT CONTAINER BERTH CATHODIC PROTECTION SYSTEM ANCHOR PLATE CALCULATIONS 0 Date: 20.12.2010
Page 8
of
4. CONCLUSION
Anchor Plate designed to resist 90 Kg of force acting on anode hanging system caused by waves constructed from 316-quality stainless steel is convenient for aimed process according to calculations.
MISURATA COMMERTIAL PORT CONTAINER BERTH CATHODIC PROTECTION SYSTEM ANCHOR PLATE CALCULATIONS 0 Date: 20.12.2010
Page 9
of
5. ATTACHMENTS
MISURATA COMMERTIAL PORT CONTAINER BERTH CATHODIC PROTECTION SYSTEM ANCHOR PLATE CALCULATIONS 0 Date: 20.12.2010