Académique Documents
Professionnel Documents
Culture Documents
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
(start en-
gine
(WP 0041)
procedure
completed).
NOTE
Air pressure buzzer will sound
anytime low air indicator is il-
luminated. Ensure low air in-
dicator and buzzer activate
when air pressure falls below
60 to 75 psi (414 to 517 kPa)
in either front or rear air sys-
tem.
0125-23
TM 9-2320-420-10 0125
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
0125-24
TM 9-2320-420-10 0125
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
FUEL GAUGE
AIR FILTER
RESTRICTION
PARKING
BRAKE
INDICATOR
EXEXEX
EXEX EXEX
TRAILER
AIR SUPPLY
EXEXEX
ENGINE
OFF
ON
START
AIR BRAKE
WATER TEMP
GAUGE
TRANS TEMP
GAUGE
Figure 11.
NOTE
Several minutes are required
for engine to warm up so an
accurate reading can be tak-
en.
0125-25
TM 9-2320-420-10 0125
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
140°F
(60°C) or
more than
230°F
(110°C) af-
ter engine
has been
properly
warmed up
(start en-
gine
(WP 0041)
procedure
completed).
NOTE
Transmission may not reach
160°F (71°C) oil temperature
at idle for several minutes.
0125-26
TM 9-2320-420-10 0125
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
to complete
the mission.
CAUTION
Vehicle must be parked when
making this check. Failure to
comply may result in damage
to equipment. Transfer case
will be damaged if shifted
while vehicle is moving.
NOTE
• Engine must be running
to perform this check.
• Transmission must be in
N (neutral) to perform this
check.
0125-27
TM 9-2320-420-10 0125
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
TRACTION
CONTROL LEVER 8X8
INDICATOR
INTER-AXLE
DIFF LOCK
INDICATOR
JACO
BS
TRANSFER
ENGIN
E BR
AKE
CASE SHIFT
LEVER
CAUT
ION
EXHA
O
LER
U
PULL T
ST
TRAI PPKINLY G
SUPARD
R FOR
AINOT LAN
O
MID
HT
PUS
Figure 12.
0125-28
TM 9-2320-420-10 0125
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
NOTE
• Engine must be running
to perform this check.
• Engine and transmission
oil must be warm to
perform this check.
• Testing has shown that a
reading of at least 180°F
(64°C) on the WATER
TEMP gauge is sufficient
to perform this check.
NOTE
Dashboard parking brake in-
dicator will illuminate when
PARKING BRAKE control is
applied.
0125-29
TM 9-2320-420-10 0125
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
JACOBS®
JACOBS® ENGINE BRAKE
ENGINE BRAKE HIGH-LOW SWITCH
ON/OFF SWITCH JACOBS®
ENGINE BRAKE
PARKING INDICATOR
BRAKE
CONTROL
JACO
BS
ENGIN
E BR
AKE
CAUT
ION
EXHA
O
LER
U
PULL T
ST
TRAI PPKINLY
G
SUPARD
AIR FOR LAN
NOT MID
O
HT
PUS
TRANSFER
CASE SHIFT
LEVER
TRANSMISSION
RANGE
SELECTOR
THOTTLE
PEDAL
Figure 13.
0125-30
TM 9-2320-420-10 0125
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
0125-31
TM 9-2320-420-10 0125
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
NOTE
Engine must be running to
perform this check.
0125-32
TM 9-2320-420-10 0125
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
NOTE
Engine must be running to
perform this check.
PTO INDICATOR
LIGHT PTO ENGAGE
SWITCH
JACOB
S
ENG
INE BR
AKE
CAUT
ION
EXHA
O
LER LY
U
PULL T
ST
TRAI PPKING
SUPARD
AIR FOR LAN
NOT MID
O
HT
PUS
Figure 14.
0125-33
TM 9-2320-420-10 0125
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
NOTE
Operation of vehicle with mal-
functioning windshield wiper
may violate AR 385-55.
(WP 0141)
JACO
BS
ENGIN
E BR
AKE
CAUT
ION
EXHA
O
LER
U
PULL T
ST
TRAI PPKINLY G
SUPAR
AIR FOR LAND
NOT MID
O
HT
PUS
WIPER/WASHER
CONTROL
Figure 15.
0125-34
TM 9-2320-420-10 0125
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
NOTE
• Engine must be running
to perform this check.
• Operation of vehicle with
malfunctioning
windshield wiper may
violate AR 385-55.
(WP 0141)
0125-35
TM 9-2320-420-10 0125
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
PARKING BRAKE
CONTROL
PARKING
BRAKE
EXEXEX
EXEX EXEX
TRAILER
AIR SUPPLY
EXEXEX
ENGINE
OFF
ON
START
AIR BRAKE
Figure 16.
NOTE
Dashboard parking brake in-
dicator will illuminate when
0125-36
TM 9-2320-420-10 0125
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
NOTE
Operator may continue on
with mission if vehicle re-
quires no servicing.
0125-37
TM 9-2320-420-10 0126
OPERATOR MAINTENANCE
DURING - PREVENTIVE MAINTENANCE
INITIAL SETUP:
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
WARNING
NOTE
Check trailer handbrake con-
trol lever only if a trailer is
hooked up to vehicle.
0126-1
TM 9-2320-420-10 0126
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
TRAILER HANDBRAKE
CONTROL LEVER
JACO
BS
ENGIN
E BR
AKE
CAUT
ION
EXHA
O
LER
U
PULL T
ST
TRAI PPKINLY G
SUPARD
R FOR
AINOT LAN
O
MID
HT
PUS
Figure 1.
NOTE
During operation, all gauges
should maintain the proper
0126-2
TM 9-2320-420-10 0126
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
WARNING
0126-3
TM 9-2320-420-10 0126
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
WARNING
0126-4
TM 9-2320-420-10 0126
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
HEAVY-DUTY
WINCH
CABLE
Figure 2.
WARNING
0126-5
TM 9-2320-420-10 0126
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
WARNING
NOTE
• PMCS for heavy-duty
winch should only be
performed when retrieval
system is required for
mission.
• Engine must be running
to perform this check.
• Check all controls and
hardware for proper
operation, (WP 0037)
obvious damage, missing
0126-6
TM 9-2320-420-10 0126
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
WINCH
CONTROL
LEVER CABLE
WINCH HOLD DOWN
KICKOUT CONTROL
CONTROL
HIGH
IDLE
SWITCH
REMOTE-CONTROL
UNIT RECEPTACLE
Figure 3.
0126-7
TM 9-2320-420-10 0126
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
binds, or
does not re-
spond to in-
put.
WARNING
0126-8
TM 9-2320-420-10 0126
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
WARNING
NOTE
• PMCS for heavy-duty
winch should only be
performed when retrieval
system is required for
mission.
• Engine must be running
to perform this check.
• Check all controls and
hardware for proper
operation, (WP 0039)
obvious damage, missing
0126-9
TM 9-2320-420-10 0126
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
REMOTE-CONTROL
UNIT
WINCH
CONTROL HIGH IDLE
LEVER SWITCH
REMOTE-CONTROL
UNIT CABLE
Figure 4.
0126-10
TM 9-2320-420-10 0126
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
binds, or
does not re-
spond to in-
put.
0126-11
TM 9-2320-420-10 0127
OPERATOR MAINTENANCE
AFTER - PREVENTIVE MAINTENANCE
INITIAL SETUP:
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
WARNING
0127-1
TM 9-2320-420-10 0127
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
NOTE
Perform Operator's Before,
After, and Weekly PMCS
checks if:
• You are the assigned
driver but have not
operated the vehicle
since the last weekly
inspection.
• You are operating the
vehicle for the first time.
NOTE
• Clean all lubrication
points with cleaning
compound, solvent and
allow to dry prior to
servicing.
• When using a grease
gun, apply lubricant to the
fitting until clean lubricant
squeezes out of the part
being lubricated.
• Always refer to lubrication
instructions (WP 0131) to
ensure equipment has
correct lubricants
appropriate to operating
environment (expected
continuous
temperatures). If not,
remove/drain and
reapply/refill equipment
with appropriate
lubricants for operating
environment as
0127-2
TM 9-2320-420-10 0127
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
prescribed in lubrication
instructions. (WP 0131)
1 After Underne 1. Check entire underside of vehicle Any fuel,
ath for fluid and air leaks. Class III
Vehicle leak, or air
lines/fittings
leaking or
damaged.
WARNING
CAUTION
Do not fill hydraulic reservoir
past FULL COLD mark. Fail-
0127-3
TM 9-2320-420-10 0127
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
NOTE
• Hydraulic oil expands
when heated, which may
give the operator false
(high) fluid level readings
if the vehicle has been
recently operated.
• If possible, wait until
hydraulic reservoir is
completely cooled down
(minimum of 2 hours)
prior to adding hydraulic
oil, otherwise fill reservoir
to FULL COLD mark.
0127-4
TM 9-2320-420-10 0127
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
“FULL COLD”
LEVEL
SIGHT GLASS
HYDRAULIC
RESERVOIR
Figure 1.
0127-5
TM 9-2320-420-10 0127
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
0127-6
TM 9-2320-420-10 0127
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
cracked, or
bent.
WARNING
0127-7
TM 9-2320-420-10 0127
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
NOTE
• Only drain air reservoirs
that are located under the
passenger side battery
box.
• The M983A2 and
M983A2 LET have three
air reservoirs under the
battery box, all other
models have two.
Figure 2.
0127-8
TM 9-2320-420-10 0127
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
CAUTION
Clean around end of fill tube
prior to removing dipstick.
This will aid in preventing dirt
or foreign matter from enter-
ing the transmission and
causing damage.
NOTE
Vehicle is parked (WP 0053)
on a flat, level surface.
Engine is at idle.
Transmission is at normal
operating temperature,
160-200°F (71-93°C).
0127-9
TM 9-2320-420-10 0127
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
TRANSMISSION
DIPSTICK
Figure 3.
NOTE
Fluid level should be between
HOT FULL and HOT ADD
marks.
0127-10
TM 9-2320-420-10 0127
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
unservicea-
ble.
NOTE
Operation of vehicle with bro-
ken/missing mirrors may vio-
late AR 385-55. (WP 0141)
0127-11
TM 9-2320-420-10 0127
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
MIRRORS
Figure 4.
NOTE
Operation of vehicle with
damaged or missing wind-
shield may violate AR 385-55.
(WP 0141)
0127-12
TM 9-2320-420-10 0127
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
WINDSHIELD
WINDSHIELD WIPER
ARMS/BLADES
Figure 5.
NOTE
Operation of vehicle with
damaged wiper arms/blades
may violate AR 385-55.
(WP 0141)
0127-13
TM 9-2320-420-10 0127
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
FAN
SWITCH
JACO
BS
ENGIN
E BR
AKE
CAUT
ION
Figure 6.
NOTE
Operation of vehicle with mal-
functioning windshield wiper
may violate AR 385-55.
(WP 0141)
0127-14
TM 9-2320-420-10 0127
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
JACO
BS
ENGIN
E BR
AKE
CAUT
ION
EXHA
O
LER
U
PULL T
ST
TRAI PPKINLY
G
SUPARD
AIR FOR LAN
NOT MID
O
HT
PUS
WIPER/WASHER
CONTROL
Figure 7.
NOTE
Operation of vehicle with mal-
functioning horn may violate
AR AR 385-55. (WP 0141)
0127-15
TM 9-2320-420-10 0127
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
NOTE
• Light checks will require
assistance.
• Operation of vehicle with
malfunctioning turn signal
control may violate AR
385-55. (WP 0141)
0127-16
TM 9-2320-420-10 0127
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
PARKING
BRAKE
EXEXEX
EXEX EXEX
TRAILER
AIR SUPPLY
EXEXEX
TURN SIGNAL
CONTROL
ENGINE
OFF
ON
START
AIR BRAKE
Figure 8.
NOTE
• Light checks will require
assistance.
• Operation of vehicle with
malfunctioning
emergency flasher
0127-17
TM 9-2320-420-10 0127
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
EMERGENCY
FLASHER CONTROL
JACOBS
ENG
INE BRA
KE
CAUT
ION
EXHA
O
ER
U
PULL T
ST
TRAIL PPKINGLY
SUPAR
AIR FOR AND
NOT MIDL
O
HT
PUS
Figure 9.
NOTE
• Light checks will require
assistance.
• Operation of vehicle with
malfunctioning service
lights may violate AR
385-55. (WP 0141)
0127-18
TM 9-2320-420-10 0127
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
NOTE
Operation of vehicle with mal-
functioning beacon light may
violate AR 385-55.
(WP 0141)
WARNING
WARNING
0127-19
TM 9-2320-420-10 0127
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
NOTE
Complete this PMCS proce-
dure only if heavy-duty winch
was used during mission.
NOTE
This procedure is a two sol-
dier task.
0127-20
TM 9-2320-420-10 0127
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
HEAVY-DUTY
WINCH
CABLE
Figure 10.
NOTE
This procedure is a two sol-
dier task.
NOTE
• Complete drain and refill
of heavy-duty winch drum
gearbox after first 10
hours of heavy-duty
winch operation.
• After initial 10 hour drain
and refill this procedure
0127-21
TM 9-2320-420-10 0127
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
becomes an annual
requirement.
BREATHER
FILL
DRAIN
Figure 11.
0127-22
TM 9-2320-420-10 0128
OPERATOR MAINTENANCE
WEEKLY - PREVENTIVE MAINTENANCE
INITIAL SETUP:
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
WARNING
0128-1
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
NOTE
Perform Operator's Before,
After, and Weekly PMCS
checks if:
• You are the assigned
driver but have not
operated the vehicle
since the last weekly
inspection.
• You are operating the
vehicle for the first time.
NOTE
• Lubrication intervals are
for normal operating
conditions. Intervals may
be shortened as required
for severe operating
conditions.
• Clean all lubrication
points with cleaning
compound, solvent and
allow to dry prior to
servicing.
• When using a grease
gun, apply lubricant to the
fitting until clean lubricant
squeezes out of the part
being lubricated.
• Always refer to lubrication
instructions (WP 0131) to
ensure equipment has
correct lubricants
appropriate to operating
environment (expected
continuous
0128-2
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
temperatures). If not,
remove/drain and
reapply/refill equipment
with appropriate
lubricants for operating
environment as
prescribed in lubrication
instructions. (WP 0131)
WARNING
0128-3
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
ing, or dam-
aged.
PROPELLER
SHAFTS
Figure 1.
NOTE
• When vehicle is operating
under severe conditions,
lubricate propeller shafts
and universal joints every
50 hours of vehicle
operation.
• Complete Step 2 only if
vehicle is operating under
severe conditions.
0128-4
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
0128-5
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
FRONT OF AXLE
VEHICLE BREATHER
VENT
CAP
BREATHER
BODY
Figure 2.
0128-6
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
(1/8 in. in
depth or
50% of belt
thickness),
has frays
more than 2
in. long or
excessive
play.
DRIVE BELT
PULLEY
DRIVE
BELT
MEASURE
AT CENTER
FAN
DRIVE
BELT
Figure 3.
0128-7
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
NOTE
Operation of vehicle with any
exhaust leaks may violate AR
385-55. (WP 0141)
0128-8
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
Figure 4.
0128-9
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
AIR CLEANER
CANISTER
AIR INTAKE
WEATHER CAP
CLAMP
ETHER
STARTING
AID
TUBE
CLAMP
AIR
CLEANER TUBE
DUST CAP CLAMP
Figure 5.
NOTE
Ether starting aid cartridges
will be removed and solenoid
0128-10
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
7 Weekly Fuel Check fuel tank, fuel hoses, fuel tank Any fuel
Tank connections, and fuel tank socket leak.
head pipe plug for leaks and/or
damage.
0128-11
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
FUEL LINES
CONNECTIONS
STRAPS
CONNECTIONS
FUEL TANK
PIPE PLUG
Figure 6.
0128-12
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
FUEL TANK
STRAINER
Figure 7.
0128-13
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
HYDRAULIC PUMP
Figure 8.
10 Weekly Hydraulic Check all hydraulic hose routing for Class III
Hoses obvious damage to hydraulic hoses, leak
chaffing, and leaks. present.
Chaffing or
obvious
damage to
hydraulic
hose
present.
NOTE
Clean and re-lubricate fifth
wheel parts more often when
vehicle is operated in sandy
or dusty conditions. Lubricate
daily under severe operating
conditions.
0128-14
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
FIFTH WHEEL
PLATE JAW LUBE
FIFTH WHEEL POINT
APPROACH RAMPS
Figure 9.
0128-15
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
0128-16
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
PINTLE
HOOK
Figure 10.
0128-17
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
INTER-VEHICLE
ELECTRICAL
CONNECTOR
Figure 11.
WARNING
NOTE
Inspection of passenger side
tires includes spare tire.
0128-18
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
NOTE
Operation of vehicle with
damaged/malfunctioning air
compressor may violate AR
385-55. (WP 0141)
0128-19
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
AIR
COMPRESSOR
Figure 12.
20 Weekly Secondar Check secondary fuel filter for leaks Any fuel
y Fuel or damage. leak.
Filter
0128-20
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
SECONDARY FUEL
FILTER
Figure 13.
0128-21
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
Figure 14.
WARNING
0128-22
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
WARNING
0128-23
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
BATTERY
BOX
Figure 15.
0128-24
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
REEL CABLE
PULLEY
Figure 16.
0128-25
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
Figure 17.
25 Weekly Air Dryer Check air dryer for loose screws and
connections.
0128-26
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
AIR
DRYER
Figure 18.
NOTE
Pressurize air system prior to
performing this check.
26 Weekly Air Lines Check routing, for obvious damage to Any leaks or
and air lines and hoses. Check for leaks. damage to
Hoses air lines, ho-
ses, or fit-
0128-27
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
tings are
found.
NOTE
Operation of vehicle with
damaged doors or windows
may violate AR 385-55.
(WP 0141)
NOTE
Start Engine. (WP 0041) En-
gine must be running for re-
maining PMCS checks.
0128-28
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
FAN
CONTROL
AIR
CONTROL
HEAT
JACO
BS
CONTROL
ENGIN
E BR
AKE
DEFROST
CAU
TION
CONTROL
Figure 19.
0128-29
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
CABLE
HOLD DOWN
Figure 20.
0128-30
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
WARNING
WARNING
NOTE
This procedure is a two sol-
dier task.
0128-31
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
HEAVY-DUTY
WINCH
CABLE
Figure 21.
0128-32
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
WINCH CONTROL
LEVER
Figure 22.
0128-33
TM 9-2320-420-10 0128
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
HEAVY-DUTY WINCH
REMOTE CONTROL
CABLE
Figure 23.
NOTE
This procedure is a two sol-
dier task.
0128-34
TM 9-2320-420-10 0129
OPERATOR MAINTENANCE
SEMIANNUAL - PREVENTIVE MAINTENANCE
INITIAL SETUP:
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
WARNING
0129-1
TM 9-2320-420-10 0129
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
NOTE
• Lubrication intervals are
for normal operating
conditions. Intervals may
be shortened as required
for severe operating
conditions.
• Clean all lubrication
points with cleaning
compound, solvent and
allow to dry prior to
servicing.
• When using a grease
gun, apply lubricant to the
fitting until clean lubricant
squeezes out of the part
being lubricated.
• Always refer to lubrication
instructions (WP 0131) to
ensure equipment has
correct lubricants
appropriate to operating
environment (expected
continuous
temperatures). If not,
remove/drain and
reapply/refill equipment
with appropriate
lubricants for operating
environment as
prescribed in lubrication
instructions. (WP 0131)
1 Semian Brake Lubricate axles No. 1, No. 2, No. 3, Fitting will
nual System and No. 4 brake camshafts and slack not purge
old lubricant
0129-2
TM 9-2320-420-10 0129
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
SLACK ADJUSTER
LUBE FITTING BRAKE CAMSHAFT
LUBE FITTING
Figure 1.
NOTE
• When vehicle is operating
under severe conditions,
lubricate propeller shafts
and universal joints every
50 hours of vehicle
operation.
0129-3
TM 9-2320-420-10 0129
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
0129-4
TM 9-2320-420-10 0129
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
0129-5
TM 9-2320-420-10 0129
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
TRANSMISSION/TRANSFER
CASE PROPELLER SHAFT
AND U-JOINTS
Figure 2.
0129-6
TM 9-2320-420-10 0129
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
0129-7
TM 9-2320-420-10 0129
Item to
be
Checked Equipment
Item or Not Ready/
No. Interval Serviced Procedure Available If:
Figure 3.
0129-8