Académique Documents
Professionnel Documents
Culture Documents
Test case
Initial Configuration
Test Steps
Expected Result
IMSI attach
1. Check that the MS transmits IMSI attach information when switched on. Monitor the radio output from the MS (this can be done with a 1. MS should be in an allowed simple FM receiver). Confirm this by arranging for PLMN the MS to receive an incoming call 2. MS is switched ON 2. Check that the MS does not display service before it is completely attached to the network 3. Check that the MS is able to receive a call immediately (3 seconds) after IMSI Attach
1. MS transmits IMSI attach 2. MS displays service after completely camping on to the network 3. MS can receive an incoming call after IMSI attach
IMSI detach
The MS shall correctly perform the IMSI detach MS is in idle mode procedure when switched off.
Switch off the MS. Monitor the radio output from the MS (this can be done with a simple FM MS transmits IMSI detach information before receiver). Check that the MS transmits IMSI detach powering down. information before powering down 1. Move the MS from the initial cell into a cell with a different LAI till the MS performs a cell reselection 2. The MS shall send a LOCATION UPDATE REPQUEST message to the network. Check whether the location updating type parameter holds the normal value 3. The network shall then send a LOCATION UPDATE ACCEPT message to the MS. This message contains a new TMSI for the MS and the LAI for the new cell 4. Check that the MS responds to paging in the new cell by calling the MS
The MS can successfully perform a normal location update after camping onto a serving cell with a different LAI.
1. MS sends a Location Update Request to the network 2. The Location Updating Type parameter holds a normal value 3. The network sends a Location Update Accept message to the MS including a new TMSI and LAI 4. The MS performs a Normal Location Update procedure and receives an incoming call.
The MS shall correctly Handover during an perform handover when MS is on an active voice call active call commanded to by the network.
Move from the coverage area of one cell to another. Ensure that the call is not dropped and that voice transmission is maintained in both directions. This procedure has to cover all the possible scenarios like: 1. Operation on different frequency bands 2. Handover between different codec types/rates 3. Handover between cells with and without frequency hopping 4. Handover between synchronised cells and handover between non-synchronised cells 5. Handover moving between the coverage areas of two different MSCs 6. Any possible combinations of the above. 7. Any combination of the above, but with a circuitswitched call in progress for other services, such as data or fax.
1. After the handover, the MS maintains a connection on the traffic channel (speech or data) in both directions 2. MS doesnt drop the call within 30 seconds of the handover.
The MS successfully performs a normal location update Normal Location procedure after camping MS is attached in Circuit Updating with TMSI onto a serving cell with a mode unknown in VLR different LAI and a TMSI which us unknown to the VLR.
1. Move the MS from the initial cell into a cell with a different LAI till the MS performs a cell reselection. 2. The MS shall send a LOCATION UPDATE REPQUEST message to the network containing a TMSI which is not known by the network. Check whether the location updating type parameter holds the normal value. 3. Check that the network initiates an Identification Procedure requesting the MSs IMSI. 4. Check that the MS sends its IMSI to the network. 5. The network shall then send a LOCATION UPDATE ACCEPT message to the MS. This message contains a new TMSI for the MS and the LAI for the new cell. 6. Check that the MS is not indicating loss of coverage. 7. Check that the MS responds to paging in the new cell by calling the MS
1. MS sends a Location Update Request containing a TMSI to the network 2. The Location Updating Type parameter holds a normal value 3. The network initiates an Identification Procedure requesting the IMSI of the MS. 4. The network sends a Location Update Accept message to the MS containing a new TMSI and LAI 5. MS doesnt indicate loss of coverage 6. The MS performs the Normal Location Update procedure (including Identification Procedure) without coverage loss indication and receives an incoming call.
Normal Operation
The MS successfully performs a periodic location update after the expiry of the T3212 timer.
1. Wait for the T3212 timer to expire, and observe if the MS sends the network a LOCATION UPDATE REQUEST message. Check whether the location updating type parameter holds the periodic updating value. 2. The network shall then send a LOCATION UPDATE ACCEPT message to the MS. 3. Check that the MS responds to paging after the Location Update procedure
1. MS sends a Location Update Request message to the network after the T3212 timer expires 2. The Location Updating Type parameter holds a periodic updating value 3. The network sends a Location Update Accept message to the MS 4. The MS performs a Periodic Location Update procedure and receives an incoming call.
Reset of T3212
1. Check that T3212 is reset when a LOCATION UPDATING ACCEPT message is received 2. Wait for the complete T3212 timer to expire, and observe that the MS does not send a LOCATION UPDATE REQUEST message until T3212 expired. When the MS performs the periodic location update procedure check whether the location updating type parameter holds the periodic updating value. 3. Check that the MS responds to paging after the Location Update procedure
1. T3212 timer is reset when a Location Update Accept message is received 2. The MS doesnt send Location Update Request until the T3212 timer expires 3. The Location Updating Type parameter holds a periodic updating value 4. The MS receives an incoming call
1. MS is attached in Circuit mode 2. MS is in idle mode 3. T3212 timer is running 4. An Authentication Reject message is received by the MS
1. Check that T3212 is reset when a LOCATION UPDATING ACCEPT message is received 2. Wait for the complete T3212 timer to expire, and observe that the MS does not send a LOCATION UPDATE REQUEST message until T3212 expired. When the MS performs the periodic location update procedure check whether the location updating type parameter holds the periodic updating value. 3. Check that the MS responds to paging after the Location Update procedure when an AUTHENTICATION REJECT message is received
1. T3212 timer is reset when a Location Update Accept message is received 2. The MS doesnt send Location Update Request until the T3212 timer expires 3. The Location Updating Type parameter holds a periodic updating value 4. The MS receives an incoming call
1. Check that T3212 is reset when a LOCATION UPDATING ACCEPT message is received 2. Wait for the complete T3212 timer to expire, 1. MS is attached in Circuit and observe that the MS does not send a mode LOCATION UPDATE REQUEST message until T3212 2. MS is in idle mode expired. When the MS performs the periodic 3. T3212 timer is running location update procedure check whether the 4. An SMS is sent or received location updating type parameter holds the on the MS periodic updating value. 3. Check that the MS responds to paging after the Location Update procedure when a SMS is sent or received
1. T3212 timer is reset when a Location Update Accept message is received 2. The MS doesnt send Location Update Request until the T3212 timer expires 3. The Location Updating Type parameter holds a periodic updating value 4. The MS receives an incoming call
10
1. MS is attached in Circuit mode 2. MS is in idle mode 3. T3212 timer is running 4. A supplementary service procedure is operated at the MS end
1. Check that T3212 is reset when a LOCATION UPDATING ACCEPT message is received 2. Wait for the complete T3212 timer to expire, and observe that the MS does not send a LOCATION UPDATE REQUEST message until T3212 expired. When the MS performs the periodic location update procedure check whether the location updating type parameter holds the periodic updating value. 3. Check that the MS responds to paging after the Location Update procedure when a Supplementary Service procedure is operated
1. T3212 timer is reset when a Location Update Accept message is received 2. The MS doesnt send Location Update Request until the T3212 timer expires 3. The Location Updating Type parameter holds a periodic updating value 4. The MS receives an incoming call
11
1. MS is attached in Circuit mode 2. MS is in idle mode 3. T3212 timer is running 4. A call is setup or received on the MS
1. Check that T3212 is reset when a LOCATION UPDATING ACCEPT message is received 2. Wait for the complete T3212 timer to expire, and observe that the MS does not send a LOCATION UPDATE REQUEST message until T3212 expired. When the MS performs the periodic location update procedure check whether the location updating type parameter holds the periodic updating value. 3. Check that the MS responds to paging after the Location Update procedure when a call is set up or received
1. T3212 timer is reset when a Location Update Accept message is received 2. The MS doesnt send Location Update Request until the T3212 timer expires 3. The Location Updating Type parameter holds a periodic updating value 4. The MS receives an incoming call
12
The MS does not reset its periodic location update MS out of coverage timer T3212 when it gets and back in coverage out of coverage and back before T3212 expiry in coverage before T3212 expiry.
1. MS is attached in Circuit mode 2. MS is in idle mode 3. T3212 timer is running 4. Move the MS out of coverage 5. The out of coverage should last for 3/4 of the T3212 interval 6. Bring the MS back to coverage before T3212 timer expires
1. Move the MS out of coverage (no other network available). The out of coverage time should last for of the interval of T3212. 2. Bring the MS back to coverage (same PLMN / Location Area as before) before T3212 expires. When gaining back coverage, check that the MS does not perform a Location Update procedure. 3. Wait for the T3212 timer to expire, and observe if the MS sends the network a LOCATION UPDATE REQUEST message. Check whether the location updating type parameter holds the periodic updating value. 4. Check that the MS responds to paging after the Location Update procedure
1. The MS sends a Location Update Request message to the network after the T3212 timer expires 2. The Location Updating Type parameter holds a periodic updating value 3. The MS receives an incoming call after completing the Location Update procedure
13
1. Move the MS out of coverage (no other network available). The out of coverage time should last 1. MS is attached in Circuit for of the interval of T3212. mode 2. Bring the MS back to coverage (same PLMN / 2. MS is in idle mode Location Area as before) before T3212 expires. 3. T3212 timer is running When gaining back coverage, check that the MS 4. Move the MS out of does not perform a Location Update procedure. coverage from the HPLMN 3. Wait for the T3212 timer to expire, and observe but camped on another PLMN if the MS sends the network a LOCATION UPDATE 5. The MS is on Emergency REQUEST message. Check whether the location Camping for atleast 3/4 of the updating type parameter holds the periodic T3212 interval updating value. 6. Bring the MS back to 4. Check that the MS responds to paging after the coverage before T3212 timer Location Update procedure when the MS is expires performing Emergency Camping on a different PLMN while out of service.
1. The MS sends a Location Update Request message to the network after the T3212 timer expires 2. The Location Updating Type parameter holds a periodic updating value 3. The MS receives an incoming call after completing the Location Update procedure
14
1. MS is attached in Circuit mode The MS performs the 2. MS is in idle mode Periodic Location Update 3. T3212 timer is running procedure immediately MS out of coverage 4. Move the MS out of after regaining service and back in coverage coverage when it gets out of after T3212 expiry 5. The out of coverage should coverage and back in last longer than the T3212 coverage after T3212 interval expiry. 6. Bring the MS back to coverage
1. Move the MS out of coverage (no other network available). The out of coverage time should last longer than the interval of T3212. 2. Bring the MS back to coverage (same PLMN / Location Area as before) after T3212 expired. When gaining back coverage, check that the MS immediately performs a Location Update procedure. 3. Check whether the location updating type parameter holds the periodic updating value. 4. Check that the MS responds to paging after the Location Update procedure
1. The MS performs immediately a Location Update procedure after regaining service. 2. The Location Updating Type parameter holds the periodic updating value 3. The MS receives an incoming call after each test.
15
1. Move the MS out of coverage (no other network available). The out of coverage time should last 1. MS is attached in Circuit longer than the interval of T3212. mode 2. Bring the MS back to coverage (same PLMN / 2. MS is in idle mode Location Area as before) after T3212 expired. 3. T3212 timer is running When gaining back coverage, check that the MS 4. Move the MS out of immediately performs a Location Update coverage from the HPLMN procedure. but camped on another PLMN 3. Check whether the location updating type 5. The MS is on Emergency parameter holds the periodic updating value. Camping for a longer interval 4. Check that the MS responds to paging after the than the T3212 interval Location Update procedure when the MS is performing Emergency Camping on a different PLMN while out of service 1. SIM has CS/PS enabled for roaming with access to all available networks 2. MS is switched-off in Device selects a Verification that the Automatic Network Selection prioritised network device correctly selects a mode outside the HPLMN (PLMNsel List on the designated and coverage SIM (<=rel98)) prioritised network. 3. MS is powered ON at some location where atleast 2 network providers should be available with signal strength > -85dBm
1. The MS performs immediately a Location Update procedure after regaining service. 2. The Location Updating Type parameter holds the periodic updating value 3. The MS receives an incoming call after each test.
16
The device shall select the prioritised network in the EFPLMNsel and ignore non-prioritised
PLMNs.
17
1. Preferred network and a second PLMN is available 2. SIM has CS/PS enabled with access to all available networks Device selects a Verification that the 3. MS is switched-off in prioritised network device correctly selects a Automatic Network Selection (User controlled designated and mode outside the HPLMN PLMNwAcT List on the prioritised network. coverage SIM/USIM (>=rel99)) 4. MS is powered ON at some location where atleast 2 network providers should be available with signal strength > -85dBm
The device shall select the prioritised PLMN network and ignore the non-prioritised PLMNs.
18
1. Preferred network and a second PLMN is available 2. SIM has CS/PS enabled with access to all available networks Device selects a Verification that the 3. MS is switched-off in prioritised network device correctly selects a Automatic Network Selection (Operator controlled designated and mode outside the HPLMN OPLMNwAcT List on prioritised network. coverage the SIM (>=rel99)) 4. MS is powered ON at some location where atleast 2 network providers should be available with signal strength > -85dBm
The device shall select the prioritised PLMN and ignore the non-prioritised PLMNs.
19
1. The HPLMN Search Period Timer is set to 6 minutes ("01") 2. MS is powered ON in Device re-selects a Automatic Network Selection To identify the behaviour prioritised network. mode at some location where of the device if the HPLMN Timer expires atleast 2 network providers HPLMN Search Period in a coverage area should be available with Timer expires in an area with no higher signal strength > -85dBm where no prioritised prioritised network 3. The tester shall wait for a network is available. coverage period of time greater than the HPLMN Search Period Timer (EFHPPLMN) to ensure a PLMN background scan is activated
It shall be checked that the device stays after expiry of HPLMN Search Period Timer (EFHPPLMN) on the same VPLMN
20
1. The HPLMN Search Period Timer is set to 6 minutes ("01") 2. MS is powered ON in Automatic Network Selection mode at some location where atleast 2 network providers To identify the behaviour should be available with signal strength > -85dBm of the device when it 3. While driving around the camps on a prioritised network and the HPLMN coverage of VPLMN A shall loose all radio coverage and Search Period Timer camp on to less prioritised (EFHPPLMN) expires in an VPLMN B area were a higher prioritised network is 4. Drive to a location where available. VPLMN A and VPLMN B are available 5. The tester shall wait for a period of time greater than the HPLMN Search Period Timer (EFHPPLMN) to ensure a PLMN background scan is activated
It shall be checked that the device selects VPLMN A after expiry of HPLMN Search Period Timer (EFHPPLMN).
21
Device re-selects a higher prioritised network when camping on a non prioritised network
1. The HPLMN Search Period Timer is set to 6 minutes ("01") 2. MS is powered ON in Automatic Network Selection mode at some location where atleast 2 network providers To identify the behaviour should be available with signal strength > -85dBm of the device when it 3. While driving around the camps on a non prioritised network and coverage of VPLMN A shall the HPLMN Search Period loose all radio coverage and Timer (EFHPPLMN) expires camp on to non prioritised in an area were a higher VPLMN B prioritised network is 4. Drive to a location where available. VPLMN A and VPLMN B are available 5. The tester shall wait for a period of time greater than the HPLMN Search Period Timer (EFHPPLMN) to ensure a PLMN background scan is activated 1. Select the manual network selection mode on the MS and ensure that the list of all available GSM If in manual network PLMNs is displayed, and that the displayed selection mode, the MS 1. MS is switched ON in networks can be selected, even if on the forbidden shall list all available Automatic Network Selection list. PLMNs. This behaviour is mode 2. Check that the preferred PLMN list is not independent from the 2. Manual Network Selection changed after the manual network selection. content of the preferred mode is selected 3. Repeat the test with different entries in the PLMN list. preferred PLMN lists, including the empty list and lists of more than 32 entries
It shall be checked that the device selects VPLMN A after expiry of HPLMN Search Period Timer (EFHPPLMN).
22
1. The MS shall display all available GSM PLMNs and it shall perform manual network selection on the chosen network. 2. The preferred PLMN list is not changed after the manual network selection.
23
The MS shall be retain its configuration of MS is switched ON in Change to manual network selection. Turn the MS Selection mode MS has Manual Network Selection mode in automatic and manual Automatic Network Selection off and on again. Check that the manual network following switch off use network selection modes mode selection mode is in use when switched off.
24
MS is switched ON in Manual Change to automatic network selection. Turn the Network Selection mode MS off and on again. Check that the automatic network selection mode is in use 1. Make a voice call to an ISDN number. Ensure that the call completes, and that the distant party receives the correct CLIP information. 2. Make a voice call to a PSTN number. Ensure that the call completes. 3. Make a voice call to a PBX extension. Ensure that 1. MS is in idle mode the call completes. 2. Attempt to call to an ISDN/ 4. Make a voice call to a Mobile number. Ensure PSTN/ PBX/ Mobile number that the call completes. from the MS Check that Call Waiting Notification, COLP and SS notification (such as "call is forwarded") is correctly displayed and does not disturb the call setup. Check that alerting tone is audible at the MS and that voice connection in both directions is established
25
1. MS call make voice call to the number, alerting indication is audible, voice connection is successful from both the directions, the call gets completed and the distant party gets the correct CLIP information 2. MS displays Call Waiting notification correctly if the user is busy 3. COLP is displayed correctly on the MS 4. SS notification is correctly displayed on the MS
26
1. Make a voice call to a busy ISDN number. Ensure that the mobile correctly indicates the busy status of the distant party. 2. Make a voice call to a busy PSTN number. Ensure that the mobile correctly indicates the busy status of the distant party. 3. Make a voice call to a busy PBX extension. The MS shall make an 1. MS is in idle mode Ensure that the mobile correctly indicates the busy Mobile originated call outgoing voice call to a 2. The called busy subscriber status of the distant party. to occupied phone busy phone and correctly should not have Call Waiting 4. Make a voice call to a busy Mobile number. indicate the busy status. services activated Ensure that the mobile correctly indicates the busy status of the distant party. Check that SS notification (such as "call is forwarded") is correctly displayed and does not disturb the call setup. Check that busy tone is audible at the MS
The MS can attempt calls to any number correctly, and SS notification information is correctly displayed and that busy indication is audible.
27
The MS shall correctly make an international call Mobile originated call using a number provided to international BMS is in idle mode in the international subscriber (with "+") format (using the + prefix)
Make a voice call to a number in another country, by using a number including the + international prefix and the full international number. Check that Call Waiting Notification, COLP and SS notification (such as "call is forwarded") is correctly displayed and does not disturb the call setup. Check that alerting tone is audible at the MS and that voice connection in both directions is established Make a voice call to a number in the same country as the mobile, by using a number including the + international prefix and the full international number.
28
MS is in idle mode
Check that Call Waiting Notification, COLP and SS notification (such as "call is forwarded") is correctly displayed and does not disturb the call setup. Check that alerting tone is audible at the MS and that voice connection in both directions is established Make a voice call to a stored international number, by using a number including the + international prefix and the full international number.
29
MS is in idle mode
Check that Call Waiting Notification, COLP and SS notification (such as "call is forwarded") is correctly displayed and does not disturb the call setup. Check that alerting tone is audible at the MS and that voice connection in both directions is established Make a voice call to a stored number in the same country as the mobile, by using a number including the + international prefix and the full international number.
30
MS is in idle mode
Check that Call Waiting Notification, COLP and SS notification (such as "call is forwarded") is correctly displayed and does not disturb the call setup. Check that alerting tone is audible at the MS and that voice connection in both directions is established
1. MS can make voice call to a Mobile number, alerting indication is audible, voice connection is successful from both the directions, the call gets completed and the distant party gets the correct CLIP information 2. MS displays Call Waiting notification correctly if the user is busy 3. COLP is displayed correctly on the MS 4. SS notification is correctly displayed on the MS 1. MS call make voice call to a Mobile number, alerting indication is audible, voice connection is successful from both the directions, the call gets completed and the distant party gets the correct CLIP information 2. MS displays Call Waiting notification correctly if the user is busy 3. COLP is displayed correctly on the MS 4. SS notification is correctly displayed on the MS 1. MS call make voice call to a Mobile number, alerting indication is audible, voice connection is successful from both the directions, the call gets completed and the distant party gets the correct CLIP information 2. MS displays Call Waiting notification correctly if the user is busy 3. COLP is displayed correctly on the MS 4. SS notification is correctly displayed on the MS 1. MS call make voice call to a Mobile number, alerting indication is audible, voice connection is successful from both the directions, the call gets completed and the distant party gets the correct CLIP information 2. MS displays Call Waiting notification correctly if the user is busy 3. COLP is displayed correctly on the MS 4. SS notification is correctly displayed on the MS
31
The MS shall present the correct CLIP information on an incoming call from a PSTN phone
1. MS is in idle mode 2. Receive a call from an ISDN/ PSTN/ PBX/ Mobile phone
1. Receive a call from an analogue PSTN phone. If CLIP information is available, ensure it is correctly displayed. Answer the call and ensure that a connection has been made. 2. Receive a call from an ISDN phone. Ensure that CLIP information is correctly displayed. Answer the call and ensure that a connection has been made. 3. Receive a call from an PBX extension. Ensure that CLIP information is correctly displayed. Answer the call and ensure that a connection has been made. 4. Receive a call from an Mobile phone Ensure that CLIP information is correctly displayed. Answer the call and ensure that a connection has been made.
CLIP information is correctly displayed, alerting indication is audible, and a voice connection in both directions is established when the user answers the call.
32
An MS shall permit Interrogation for the interrogation of CLIP CLIP status (*#30#) status The MS shall correctly Interrogation for the indicate its CLIR status in CLIR status (*#31#) response to a command from the user. The MS shall correctly send DTMF digits when engaged in a call.
1. Dial *#30#, and ensure that the phone correctly 1. MS is in idle mode indicates the CLIP status. 2. Dial *#30# from the phone 2. Interrogate the CLIP status using the phone CLIP status is correctly displayed. and interrogate the CLIP menus, and ensure that the phone correctly status indicates the CLIP status. 1. MS is in idle mode 2. Dial *#31# from the phone and interrogate the CLIP status 1. MS is connected to an active voicemail system or other DTMF receiver 2. Press any digits from 0-9 or # 1. Dial *#31#, and ensure that the phone correctly indicates the CLIR status. CLIR status is correctly displayed. 2. Repeat procedure 1, but using the phone's menus to send the command. 1. Check that the voicemail system responds correctly to the digits 0-9, * and #. 2. Check by sending DTMF digits stored in the phonebook memory.
33
34
DTMF
The voicemail system responds correctly to the digits sent by the MS.
35
1. SIM is inserted in the MS 2. No Emergency Number information stored on the SIM 3. MS is switched-ON and key Emergency calls, with pad is unlocked/ locked SIM/USIM, no The UE shall make an 4. Attempt emergency call to emergency number outgoing emergency call. international emergency stored numbers 112 and 911, national emergency numbers 100, 101, 102, 108, etc. or successively dial 08, 100, 108, 110, 119, etc.
1. Make an emergency call to the international emergency numbers 112 and 911 2. Make an emergency call dialling successively 08, 000, 110, 118, 119, 999 3. Make an emergency call dialling any other specific national emergency number of the country 4. Make an emergency call without dialling any dedicated number, if the UE MMI allows so (such as use of the menu, of a special button, etc.)
1. The MS shall complete the call correctly, display specific emergency call set-up MMI correctly 2. Alerting indication should be audible, and a voice connection in both directions should be established with the emergency services. (No call should be established for the successive dialling of the emergency numbers)
36
1. SIM is inserted in the MS 2. No Emergency Number information stored on the SIM 3. MS is switched-ON 4. FDN is either activated or deactivated 5. Attempt emergency call to international emergency numbers 112 and 911, national emergency numbers 100, 101, 102, 108, etc. or successively dial 08, 100, 108, 110, 119, etc.
1. Make an emergency call to the international emergency numbers 112 and 911 2. Make an emergency call dialling successively 08, 000, 110, 118, 119, 999 3. Make an emergency call dialling any other specific national emergency number of the country 4. Make an emergency call without dialling any dedicated number, if the UE MMI allows so (such as use of the menu, of a special button, etc.)
1. The MS shall complete the call correctly, display specific emergency call set-up MMI correctly 2. Alerting indication should be audible, and a voice connection in both directions should be established with the emergency services. (No call should be established for the successive dialling of the emergency numbers)
37
1. SIM is inserted in the MS 2. No Emergency Number information stored on the SIM 3. MS is switched-ON 4. MS camped on a Forbidden PLMN 5. Attempt emergency call to international emergency numbers 112 and 911, national emergency numbers 100, 101, 102, 108, etc. or successively dial 08, 100, 108, 110, 119, etc.
1. Make an emergency call to the international emergency numbers 112 and 911 2. Make an emergency call dialling successively 08, 000, 110, 118, 119, 999 3. Make an emergency call dialling any other specific national emergency number of the country 4. Make an emergency call without dialling any dedicated number, if the UE MMI allows so (such as use of the menu, of a special button, etc.)
1. The MS shall complete the call correctly, display specific emergency call set-up MMI correctly 2. Alerting indication should be audible, and a voice connection in both directions should be established with the emergency services. (No call should be established for the successive dialling of the emergency numbers)
38
1. SIM is inserted in the MS 2. No Emergency Number information stored on the SIM 3. MS is switched-ON 4. IMSI is unknown in HLR 5. Attempt emergency call to international emergency numbers 112 and 911, national emergency numbers 100, 101, 102, 108, etc. or successively dial 08, 100, 108, 110, 119, etc.
1. Make an emergency call to the international emergency numbers 112 and 911 2. Make an emergency call dialling successively 08, 000, 110, 118, 119, 999 3. Make an emergency call dialling any other specific national emergency number of the country 4. Make an emergency call without dialling any dedicated number, if the UE MMI allows so (such as use of the menu, of a special button, etc.)
1. The MS shall complete the call correctly, display specific emergency call set-up MMI correctly 2. Alerting indication should be audible, and a voice connection in both directions should be established with the emergency services. (No call should be established for the successive dialling of the emergency numbers)
39
1. SIM is inserted in the MS 2. No Emergency Number information stored on the SIM 3. MS is switched-ON 4. PIN1 is blocked 5. Attempt emergency call to international emergency numbers 112 and 911, national emergency numbers 100, 101, 102, 108, etc. or successively dial 08, 100, 108, 110, 119, etc.
1. Make an emergency call to the international emergency numbers 112 and 911 2. Make an emergency call dialling successively 08, 000, 110, 118, 119, 999 3. Make an emergency call dialling any other specific national emergency number of the country 4. Make an emergency call without dialling any dedicated number, if the UE MMI allows so (such as use of the menu, of a special button, etc.)
1. The MS shall complete the call correctly, display specific emergency call set-up MMI correctly 2. Alerting indication should be audible, and a voice connection in both directions should be established with the emergency services. (No call should be established for the successive dialling of the emergency numbers)
40
1. SIM is inserted in the MS 2. No Emergency Number information stored on the SIM 3. MS is switched-ON 4. PUK is blocked 5. Attempt emergency call to international emergency numbers 112 and 911, national emergency numbers 100, 101, 102, 108, etc. or successively dial 08, 100, 108, 110, 119, etc.
1. Make an emergency call to the international emergency numbers 112 and 911 2. Make an emergency call dialling successively 08, 000, 110, 118, 119, 999 3. Make an emergency call dialling any other specific national emergency number of the country 4. Make an emergency call without dialling any dedicated number, if the UE MMI allows so (such as use of the menu, of a special button, etc.)
1. The MS shall complete the call correctly, display specific emergency call set-up MMI correctly 2. Alerting indication should be audible, and a voice connection in both directions should be established with the emergency services. (No call should be established for the successive dialling of the emergency numbers)
41
1. SIM is inserted in the MS 2. Emergency Number information is stored on the SIM 3. MS is switched-ON 4. PIN protection is activated Emergency calls, with 5. Attempt emergency call to SIM/USIM, emergency The UE shall make an international emergency numbers stored on outgoing emergency call. numbers 112 and 911, EFECC national emergency numbers 100, 101, 102, 108, etc. or successivley dial all numbers stored on the SIM or successively dial 08, 100, 108, 110, 119, etc.
1. Make an emergency call to the international emergency numbers 112 and 911 2. Make an emergency call dialling successively all numbers stored in SIM/USIM (EFECC) 3. Make an emergency call dialling successively 08, 000, 110, 118, 119, 999 except if this number is stored in EFECC 4. Make an emergency call dialling any other specific national emergency number of the country 5. Make an emergency call without dialling any dedicated number, if the UE MMI allows so (such as use of the menu, of a special button, etc.)
1. The MS shall complete the call correctly, display specific emergency call set-up MMI correctly 2. Alerting indication should be audible, and a voice connection in both directions should be established with the emergency services. (No call should be established for the successive dialling of the emergency numbers but for successive dialling from stored numbers, it will work fine)
42
1. SIM is inserted in the MS 2. Emergency Number information is stored on the SIM 3. MS is switched-ON 4. PIN protection is activated 5. Key pad is locked 6. Attempt emergency call to international emergency numbers 112 and 911, national emergency numbers 100, 101, 102, 108, etc. or successivley dial all numbers stored on the SIM or successively dial 08, 100, 108, 110, 119, etc.
1. Make an emergency call to the international emergency numbers 112 and 911 2. Make an emergency call dialling successively all numbers stored in SIM/USIM (EFECC) 3. Make an emergency call dialling successively 08, 000, 110, 118, 119, 999 except if this number is stored in EFECC 4. Make an emergency call dialling any other specific national emergency number of the country 5. Make an emergency call without dialling any dedicated number, if the UE MMI allows so (such as use of the menu, of a special button, etc.)
1. The MS shall complete the call correctly, display specific emergency call set-up MMI correctly 2. Alerting indication should be audible, and a voice connection in both directions should be established with the emergency services. (No call should be established for the successive dialling of the emergency numbers but for successive dialling from stored numbers, it will work fine)
43
1. SIM is inserted in the MS 2. Emergency Number information is stored on the SIM 3. MS is switched-ON 4. PIN protection is activated 5. FDN is activated 6. Attempt emergency call to international emergency numbers 112 and 911, national emergency numbers 100, 101, 102, 108, etc. or successivley dial all numbers stored on the SIM or successively dial 08, 100, 108, 110, 119, etc.
1. Make an emergency call to the international emergency numbers 112 and 911 2. Make an emergency call dialling successively all numbers stored in SIM/USIM (EFECC) 3. Make an emergency call dialling successively 08, 000, 110, 118, 119, 999 except if this number is stored in EFECC 4. Make an emergency call dialling any other specific national emergency number of the country 5. Make an emergency call without dialling any dedicated number, if the UE MMI allows so (such as use of the menu, of a special button, etc.)
1. The MS shall complete the call correctly, display specific emergency call set-up MMI correctly 2. Alerting indication should be audible, and a voice connection in both directions should be established with the emergency services. (No call should be established for the successive dialling of the emergency numbers but for successive dialling from stored numbers, it will work fine)
44
1. SIM is inserted in the MS 2. Emergency Number information is stored on the SIM 3. MS is switched-ON 4. PIN protection is activated 5. MS camped on FPLMN 6. Attempt emergency call to international emergency numbers 112 and 911, national emergency numbers 100, 101, 102, 108, etc. or successivley dial all numbers stored on the SIM or successively dial 08, 100, 108, 110, 119, etc.
1. Make an emergency call to the international emergency numbers 112 and 911 2. Make an emergency call dialling successively all numbers stored in SIM/USIM (EFECC) 3. Make an emergency call dialling successively 08, 000, 110, 118, 119, 999 except if this number is stored in EFECC 4. Make an emergency call dialling any other specific national emergency number of the country 5. Make an emergency call without dialling any dedicated number, if the UE MMI allows so (such as use of the menu, of a special button, etc.)
1. The MS shall complete the call correctly, display specific emergency call set-up MMI correctly 2. Alerting indication should be audible, and a voice connection in both directions should be established with the emergency services. (No call should be established for the successive dialling of the emergency numbers but for successive dialling from stored numbers, it will work fine)
45
1. SIM is inserted in the MS 2. Emergency Number information is stored on the SIM 3. MS is switched-ON 4. PIN protection is activated 5. IMSI is unknown in HLR 6. Attempt emergency call to international emergency numbers 112 and 911, national emergency numbers 100, 101, 102, 108, etc. or successivley dial all numbers stored on the SIM or successively dial 08, 100, 108, 110, 119, etc.
1. Make an emergency call to the international emergency numbers 112 and 911 2. Make an emergency call dialling successively all numbers stored in SIM/USIM (EFECC) 3. Make an emergency call dialling successively 08, 000, 110, 118, 119, 999 except if this number is stored in EFECC 4. Make an emergency call dialling any other specific national emergency number of the country 5. Make an emergency call without dialling any dedicated number, if the UE MMI allows so (such as use of the menu, of a special button, etc.)
1. The MS shall complete the call correctly, display specific emergency call set-up MMI correctly 2. Alerting indication should be audible, and a voice connection in both directions should be established with the emergency services. (No call should be established for the successive dialling of the emergency numbers but for successive dialling from stored numbers, it will work fine)
46
1. SIM is inserted in the MS 2. Emergency Number information is stored on the SIM 3. MS is switched-ON 4. PIN protection is activated 5. PIN1 is blocked 6. Attempt emergency call to international emergency numbers 112 and 911, national emergency numbers 100, 101, 102, 108, etc. or successivley dial all numbers stored on the SIM or successively dial 08, 100, 108, 110, 119, etc.
1. Make an emergency call to the international emergency numbers 112 and 911 2. Make an emergency call dialling successively all numbers stored in SIM/USIM (EFECC) 3. Make an emergency call dialling successively 08, 000, 110, 118, 119, 999 except if this number is stored in EFECC 4. Make an emergency call dialling any other specific national emergency number of the country 5. Make an emergency call without dialling any dedicated number, if the UE MMI allows so (such as use of the menu, of a special button, etc.)
1. The MS shall complete the call correctly, display specific emergency call set-up MMI correctly 2. Alerting indication should be audible, and a voice connection in both directions should be established with the emergency services. (No call should be established for the successive dialling of the emergency numbers but for successive dialling from stored numbers, it will work fine)
47
1. SIM is inserted in the MS 2. Emergency Number information is stored on the SIM 3. MS is switched-ON 4. PIN protection is activated 5. PUK is blocked 6. Attempt emergency call to international emergency numbers 112 and 911, national emergency numbers 100, 101, 102, 108, etc. or successivley dial all numbers stored on the SIM or successively dial 08, 100, 108, 110, 119, etc.
1. Make an emergency call to the international emergency numbers 112 and 911 2. Make an emergency call dialling successively all numbers stored in SIM/USIM (EFECC) 3. Make an emergency call dialling successively 08, 000, 110, 118, 119, 999 except if this number is stored in EFECC 4. Make an emergency call dialling any other specific national emergency number of the country 5. Make an emergency call without dialling any dedicated number, if the UE MMI allows so (such as use of the menu, of a special button, etc.)
1. The MS shall complete the call correctly, display specific emergency call set-up MMI correctly 2. Alerting indication should be audible, and a voice connection in both directions should be established with the emergency services. (No call should be established for the successive dialling of the emergency numbers but for successive dialling from stored numbers, it will work fine)
48
The device shall make an 1. No SIM is inserted in the outgoing emergency call MS even without SIM/USIM. 2. MS is switched-ON
Attempt emergency call to international emergency numbers 112 and 911, or successively dial 08, 100, 108, 110, 119, etc.
1. The MS shall complete the call correctly, display specific emergency call set-up MMI correctly 2. Alerting indication should be audible, and a voice connection in both directions should be established with the emergency services. 1. When attempted to dial the code strings for activating different supplementary services, the MS registers the supplementary service and displays the fact correctly 2. The MS also registers supplementary services through menu commands 3. The interrogation for supplementary services should return the correct value. 1. When attempted to dial the code strings for activating different supplementary services, the MS registers the supplementary service and displays the fact correctly 2. The MS also registers supplementary services through menu commands 3. The interrogation for supplementary services should return the correct value.
49
Registration of the Call Forwarding Registration without supplementary services, basic service without reference to a specific Basic Service.
1. Dial the code string and check that the mobile displays a response indicating that the service has been registered. Check also that the service has been registered by performing an interrogation. 2. Check using menu commands also
50
Registration of the Call Forwarding 1. MS is in idle mode supplementary services, 2. Supplementary service is using a provisioned basic not registered service.
1. Dial the code string for a basic service offered by the phone and check that the mobile displays a response indicating that the service has been registered. Repeat for up to three basic services, if offered by the phone. Check also that the service has been registered by performing an interrogation 2. Check using menu commands also
51
Display message of registered and activated call forwarding during MOC setup
Display an indication of 1. MS is in idle mode call forwarding status 2. CFU is activated when making an MOC call 1. MS is in idle mode 2. CFB is activated 1. MS is in idle mode 2. CFNRy is activated 1. MS is in idle mode 2. CFNRc is activated 1. MS is in idle mode 2. All conditional CF is activated
Make an outgoing call, and check that the call forwarding status is displayed during call setup
52
Make an outgoing call, and check that the call forwarding status is displayed during call setup Make an outgoing call, and check that the call forwarding status is displayed during call setup Make an outgoing call, and check that the call forwarding status is displayed during call setup Make an outgoing call, and check that the call forwarding status is displayed during call setup 1. Dial the code string for BAOC *33*PW# (where PW is the current password) and check that the mobile displays a response indicating that the service has been activated. Check also that the service has been activated by attempting to make an outgoing call to a barred number 2. Check using menu commands also 1. Dial the code string for BOIC *331*PW# (where PW is the current password) and check that the mobile displays a response indicating that the service has been activated. Check also that the service has been activated by attempting to make an outgoing call to a barred number 2. Check using menu commands also 1. Dial the code string for BOIC-exHC *332*PW# (where PW is the current password) and check that the mobile displays a response indicating that the service has been activated. Check also that the service has been activated by attempting to make an outgoing call to a barred number 2. Check using menu commands also
The SS status is correctly displayed during MOC setup. The SS status is correctly displayed during MOC setup. The SS status is correctly displayed during MOC setup. The SS status is correctly displayed during MOC setup. 1. When attempted to dial the code strings for activating different Call Barring services, the MS displays a response indicating that the service has been activated 2. MS indicates barring for outgoing and incoming calls for the respective code strings entered 1. When attempted to dial the code strings for activating different Call Barring services, the MS displays a response indicating that the service has been activated 2. MS indicates barring for outgoing and incoming calls for the respective code strings entered 1. When attempted to dial the code strings for activating different Call Barring services, the MS displays a response indicating that the service has been activated 2. MS indicates barring for outgoing and incoming calls for the respective code strings entered
53
54
55
56
57
58
59
1. Dial the code string for BAIC *35*PW# (where PW is the current password) and check that the mobile displays a response indicating that the service has been activated. Check also that the service has been activated by attempting to make an outgoing call to a barred number. Check that the service has been activated by attempting to make an incoming call from a barred number 2. Check using menu commands also 1. Dial the code string for BAIC-R *351*PW# (where PW is the current password) and check that the mobile displays a response indicating that the service has been activated. Check also that the service has been activated by attempting to make an outgoing call to a barred number 2. Check using menu commands also 1. Dial the code string for BAOC with a provisioned basic service *33*PW*BS# (where PW is the current password and BS is the code for the basic service) and check that the mobile displays a response indicating that the service has been activated. Repeat for up to three basic services if implemented on the MS. Check also that the service has been activated by attempting to make an outgoing call to a barred number. 2. Check using menu commands as well 1. Dial the code string for BOIC *331*PW*BS# (where PW is the current password and BS is the code for the basic service) and check that the mobile displays a response indicating that the service has been activated. Repeat for up to three basic services if implemented on the MS. Check also that the service has been activated by attempting to make an outgoing call to a barred number 2. Check using menu commands as well
1. When attempted to dial the code strings for activating different Call Barring services, the MS displays a response indicating that the service has been activated 2. MS indicates barring for outgoing and incoming calls for the respective code strings entered
60
1. When attempted to dial the code strings for activating different Call Barring services, the MS displays a response indicating that the service has been activated 2. MS indicates barring for outgoing and incoming calls for the respective code strings entered
61
Activation of call barring 1. MS is in idle mode services using a 2. Call Barring service is not provisioned basic service registered
1. When attempted to dial the code strings for activating different Call Barring services, the MS displays a response indicating that the service has been activated 2. MS indicates barring for outgoing and incoming calls for the respective code strings entered
62
1. When attempted to dial the code strings for activating different Call Barring services, the MS displays a response indicating that the service has been activated 2. MS indicates barring for outgoing and incoming calls for the respective code strings entered
63
1. Dial the code string for BOIC-exHC *332*PW*BS# (where PW is the current password and BS is the code for the basic service) and check that the mobile displays a response indicating that the service has been activated. Repeat for up to three basic services if implemented on the MS. Check also that the service has been activated by attempting to make an outgoing call to a barred number 2. Check using menu commands as well 1. Dial the code string for BAIC *35*PW*BS# (where PW is the current password and BS is the code for the basic service) and check that the mobile displays a response indicating that the service has been activated. Repeat for up to three basic services if implemented on the MS. Check also that the service has been activated by attempting to make an outgoing call to a barred number 2. Check using menu commands as well 1. Dial the code string for BAIC-R *351*PW*BS#2 (where PW is the current password and BS is the code for the basic service) and check that the mobile displays a response indicating that the service has been activated. Repeat for up to three basic services if implemented on the MS. Check also that the service has been activated by attempting to make an outgoing call to a barred number 2. Check using menu commands as well
1. When attempted to dial the code strings for activating different Call Barring services, the MS displays a response indicating that the service has been activated 2. MS indicates barring for outgoing and incoming calls for the respective code strings entered
64
1. When attempted to dial the code strings for activating different Call Barring services, the MS displays a response indicating that the service has been activated 2. MS indicates barring for outgoing and incoming calls for the respective code strings entered
65
1. When attempted to dial the code strings for activating different Call Barring services, the MS displays a response indicating that the service has been activated 2. MS indicates barring for outgoing and incoming calls for the respective code strings entered
66
MS is in idle mode
1. Dial the code string for BAOC *33*PW# (where PW is the current password) and check that the mobile displays a response indicating that the command has failed. 2. Check using menu commands as well
1. When attempted to dial the code strings for activating different Call Barring services, the MS displays a response indicating that the command has failed 2. The MS displays the correct status of the call barring service when attempted through menu commands as well
67
1. Dial the code string for BOIC *331*PW# (where PW is the current password) and check that the mobile displays a response indicating that the command has failed 2. Check using menu commands as well
1. When attempted to dial the code strings for activating different Call Barring services, the MS displays a response indicating that the command has failed 2. The MS displays the correct status of the call barring service when attempted through menu commands as well 1. When attempted to dial the code strings for activating different Call Barring services, the MS displays a response indicating that the command has failed 2. The MS displays the correct status of the call barring service when attempted through menu commands as well 1. When attempted to dial the code strings for activating different Call Barring services, the MS displays a response indicating that the command has failed 2. The MS displays the correct status of the call barring service when attempted through menu commands as well 1. When attempted to dial the code strings for activating different Call Barring services, the MS displays a response indicating that the command has failed 2. The MS displays the correct status of the call barring service when attempted through menu commands as well 1. When attempted to dial the code strings for deactivating different Call Barring services, the MS displays a response indicating that the service has been deactivated 2. The MS displays a response indicating that the service has been deactivated when attempted through menu commands as well 3. MS permits a call attempt to a previously barred number
68
1. Dial the code string for BOIC-exHC *332*PW# (where PW is the current password) and check that the mobile displays a response indicating that the command has failed 2. Check using menu commands as well
69
1. Dial the code string for BAIC *35*PW# (where PW is the current password) and check that the mobile displays a response indicating that the command has failed 2. Check using menu commands as well
70
1. Dial the code string for BAIC-R *351*PW# (where PW is the current password) and check that the mobile displays a response indicating that the command has failed 2. Check using menu commands as well
71
Deactivation of call Deactivation without barring services without basic service reference to a specific basic service
1. Dial the code string for BAOC #33*PW# (where PW is the current password) and check that the mobile displays a response indicating that the service has been deactivated. Check also that the service has been deactivated by attempting to make an outgoing call to a previously barred number. 2. Check using menu commands as well
72
1. Dial the code string for BOIC #331*PW# (where PW is the current password) and check that the mobile displays a response indicating that the service has been deactivated. Check also that the service has been deactivated by attempting to make an outgoing call to a previously barred number 2. Check using menu commands as well
1. When attempted to dial the code strings for deactivating different Call Barring services, the MS displays a response indicating that the service has been deactivated 2. The MS displays a response indicating that the service has been deactivated when attempted through menu commands as well 3. MS permits a call attempt to a previously barred number
73
1. Dial the code string for BOIC-exHC #332*PW# (where PW is the current password) and check that the mobile displays a response indicating that the service has been deactivated. Check also that the service has been deactivated by attempting to make an outgoing call to a previously barred number 2. Check using menu commands as well
1. When attempted to dial the code strings for deactivating different Call Barring services, the MS displays a response indicating that the service has been deactivated 2. The MS displays a response indicating that the service has been deactivated when attempted through menu commands as well 3. MS permits a call attempt to a previously barred number
74
1. Dial the code string for BAIC #35*PW# (where PW is the current password) and check that the mobile displays a response indicating that the service has been deactivated. Check also that the service has been deactivated by attempting to make an outgoing call to a previously barred number 2. Check using menu commands as well
1. When attempted to dial the code strings for deactivating different Call Barring services, the MS displays a response indicating that the service has been deactivated 2. The MS displays a response indicating that the service has been deactivated when attempted through menu commands as well 3. MS permits a call attempt to a previously barred number
75
1. Dial the code string for BAIC-R #351*PW# (where PW is the current password) and check that the mobile displays a response indicating that the service has been deactivated. Check also that the service has been deactivated by attempting to make an outgoing call to a previously barred number 2. Check using menu commands as well
1. When attempted to dial the code strings for deactivating different Call Barring services, the MS displays a response indicating that the service has been deactivated 2. The MS displays a response indicating that the service has been deactivated when attempted through menu commands as well 3. MS permits a call attempt to a previously barred number
76
Deactivation of call 1. MS is in idle mode barring services using a 2. Call Barring service is provisioned basic service activated
1. Dial the code string for BAOC with a provisioned basic service #33*PW*BS# (where PW is the current password and BS is the code for the basic service) and check that the mobile displays a response indicating that the service has been deactivated. Repeat for up to three basic services if implemented on the MS. Check also that the service has been deactivated by attempting to make an outgoing call to a previously barred number 2. Check using menu commands as well 1. Dial the code string for BOIC #331*PW*BS# (where PW is the current password and BS is the code for the basic service) and check that the mobile displays a response indicating that the service has been deactivated. Repeat for up to three basic services if implemented on the MS. Check also that the service has been deactivated by attempting to make an outgoing call to a previously barred number 2. Check using menu commands as well 1. Dial the code string for BOIC-exHC #332*PW*BS# (where PW is the current password and BS is the code for the basic service) and check that the mobile displays a response indicating that the service has been deactivated. Repeat for up to three basic services if implemented on the MS. Check also that the service has been deactivated by attempting to make an outgoing call to a previously barred number 2. Check using menu commands as well
1. When attempted to dial the code strings for deactivating different Call Barring services, the MS displays a response indicating that the service has been deactivated 2. The MS displays a response indicating that the service has been deactivated when attempted through menu commands as well 3. MS permits a call attempt to a previously barred number
77
1. When attempted to dial the code strings for deactivating different Call Barring services, the MS displays a response indicating that the service has been deactivated 2. The MS displays a response indicating that the service has been deactivated when attempted through menu commands as well 3. MS permits a call attempt to a previously barred number
78
1. When attempted to dial the code strings for deactivating different Call Barring services, the MS displays a response indicating that the service has been deactivated 2. The MS displays a response indicating that the service has been deactivated when attempted through menu commands as well 3. MS permits a call attempt to a previously barred number
79
1. Dial the code string for BAIC #35*PW*BS# (where PW is the current password and BS is the code for the basic service) and check that the mobile displays a response indicating that the service has been deactivated. Repeat for up to three basic services if implemented on the MS. Check also that the service has been deactivated by attempting to make an outgoing call to a previously barred number 2. Check using menu commands as well 1. Dial the code string for BAIC-R #351*PW*BS# (where PW is the current password and BS is the code for the basic service) and check that the mobile displays a response indicating that the service has been deactivated. Repeat for up to three basic services if implemented on the MS. Check also that the service has been deactivated by attempting to make an outgoing call to a previously barred number 2. Check using menu commands as well
1. When attempted to dial the code strings for deactivating different Call Barring services, the MS displays a response indicating that the service has been deactivated 2. The MS displays a response indicating that the service has been deactivated when attempted through menu commands as well 3. MS permits a call attempt to a previously barred number
80
1. When attempted to dial the code strings for deactivating different Call Barring services, the MS displays a response indicating that the service has been deactivated 2. The MS displays a response indicating that the service has been deactivated when attempted through menu commands as well 3. MS permits a call attempt to a previously barred number 1. When attempted to dial the code strings for interrogating different Call Barring services, the MS displays the correct status of the call barring service 2. The MS displays the correct status of the call barring service when attempted through menu commands as well
81
Interrogation
82
Deactivation of all General deactivation currently activated of barring services barring services
1. Dial the code string #330*PW# (where PW is the current password) and check that the mobile displays a response indicating that all barring services have been deactivated. Check also that the service has been deactivated by attempting to make an outgoing call to a previously barred number 2. Check using menu commands as well
1. When attempted to dial the code strings for deactivating all Call Barring services, the MS displays a response that all the Call Barring services have been deactivated 2. The MS displays a response that all the Call Barring services have been deactivated when attempted through menu commands as well 3. The MS permits a call attempt to or from a previously barred number
83
1. Dial the code string #353*PW# (where PW is the current password) and check that the mobile displays a response indicating that all barring services have been deactivated. Check also that the service has been deactivated by attempting to make an outgoing call to a previously barred number 2. Check using menu commands as well
1. When attempted to dial the code strings for deactivating all Call Barring services, the MS displays a response that all the Call Barring services have been deactivated 2. The MS displays a response that all the Call Barring services have been deactivated when attempted through menu commands as well 3. The MS permits a call attempt to or from a previously barred number
84
1. Dial the code string #333*PW# (where PW is the current password) and check that the mobile displays a response indicating that all barring services have been deactivated. Check also that the service has been deactivated by attempting to make an outgoing call to a previously barred number 2. Check using menu commands as well
1. When attempted to dial the code strings for deactivating all Call Barring services, the MS displays a response that all the Call Barring services have been deactivated 2. The MS displays a response that all the Call Barring services have been deactivated when attempted through menu commands as well 3. The MS permits a call attempt to or from a previously barred number
85
Change of password
1. Dial the code string *03**OLD* NEW*NEW# (where OLD is the old password and NEW is the new password) and check that the mobile displays a response indicating that the password has been changed 2. Change the password using menu commands and check that the mobile displays a response indicating that the password has been changed
1. When attempted to dial the code strings for changing the password for Call Barring services, the MS displays a response that the password has been changed 2. The MS displays a response that the password has been changed when attempted through menu commands as well
86
1. Dial the code string **03**OLD*NEW*NEW# (where OLD is the old password and NEW is the new password) and check that the mobile displays a response indicating that the password has been changed 2. Change the password using menu commands and check that the mobile displays a response indicating that the password has been changed
1. When attempted to dial the code strings for changing the password for Call Barring services, the MS displays a response that the password has been changed 2. The MS displays a response that the password has been changed when attempted through menu commands as well
87
1. Dial the code string *03*330*OLD*NEW*NEW# (where OLD is the old password and NEW is the new password) and check that the mobile displays a response indicating that the password has been changed 2. Change the password using menu commands and check that the mobile displays a response indicating that the password has been changed
1. When attempted to dial the code strings for changing the password for Call Barring services, the MS displays a response that the password has been changed 2. The MS displays a response that the password has been changed when attempted through menu commands as well
88
Failure of call barring 1. MS is in idle mode Change of password, password change caused 2. Call Barring password is old password wrong by wrong old password configured
1. Dial the code string *03**OLD*NEW*NEW# (where OLD is an incorrect old password and NEW is the new password) and check that the mobile displays a response indicating that the old password was incorrect 2. Change the password using menu commands and check that the mobile displays a response indicating that the password has been changed
1. When attempted to dial the code strings for changing the password for Call Barring services, and an incorrect old password is entered, the MS displays a response that the old password is incorrect 2. The MS displays a response that the old password is incorrect when attempted through menu commands as well
89
1. Dial the code string **03**OLD*NEW*NEW# (where OLD is an incorrect old password and NEW is the new password) and check that the mobile displays a response indicating that the old password was incorrect 2. Change the password using menu commands and check that the mobile displays a response indicating that the password has been changed
1. When attempted to dial the code strings for changing the password for Call Barring services, and an incorrect old password is entered, the MS displays a response that the old password is incorrect 2. The MS displays a response that the old password is incorrect when attempted through menu commands as well
90
1. Dial the code string *03*330*OLD*NEW*NEW# (where OLD is an incorrect old password and NEW is the new password) and check that the mobile displays a response indicating that the old password was incorrect 2. Change the password using menu commands and check that the mobile displays a response indicating that the password has been changed
1. When attempted to dial the code strings for changing the password for Call Barring services, and an incorrect old password is entered, the MS displays a response that the old password is incorrect 2. The MS displays a response that the old password is incorrect when attempted through menu commands as well
91
Failure of call barring Change of password; 1. MS is in idle mode password change caused wrong repeating of 2. Call Barring password is by wrong repetition of new password configured new password
1. Dial the code string *03**OLD*NEW1*NEW2# (where OLD is the old password and NEW1 and NEW2 are different from each other) and check that the mobile displays a response indicating that the new password has not been verified 2. Change the password using menu commands and check that the mobile displays a response indicating that the password has been changed
1. When attempted to dial the code strings for changing the password for Call Barring services, new password and confirm new password are different, the MS displays a response that the new password has not been verified 2. The MS displays a response that the new password has not been verified when attempted through menu commands as well 1. When attempted to dial the code strings for changing the password for Call Barring services, new password and confirm new password are different, the MS displays a response that the new password has not been verified 2. The MS displays a response that the new password has not been verified when attempted through menu commands as well 1. When attempted to dial the code strings for changing the password for Call Barring services, new password and confirm new password are different, the MS displays a response that the new password has not been verified 2. The MS displays a response that the new password has not been verified when attempted through menu commands as well
92
1. Dial the code string **03**OLD*NEW1*NEW2# (where OLD is the old password and NEW1 and NEW2 are different from each other) and check that the mobile displays a response indicating that the new password has not been verified 2. Change the password using menu commands and check that the mobile displays a response indicating that the password has been changed 1. Dial the code string *03*330**OLD*NEW1*NEW2# (where OLD is the old password and NEW1 and NEW2 are different from each other) and check that the mobile displays a response indicating that the new password has not been verified 2. Change the password using menu commands and check that the mobile displays a response indicating that the password has been changed 1. Dial the code string *03**OLD*NEW*NEW# (where OLD is the old password and NEW is the new password only three digits long) and check that the mobile displays a response indicating that the new password has not been verified 2. Change the password using menu commands and check that the mobile displays a response indicating that the password has been changed
93
94
Failure of call barring Change of password; 1. MS is in idle mode password change caused new password wrong 2. Call Barring password is by the new password (3 digits long) configured being too short
1. When attempted to dial the code strings for changing the password for Call Barring services, new password is entered only 3 digits long, the MS displays a response that the new password has not been verified 2. The MS displays a response that the new password has not been verified when attempted through menu commands as well
95
1. Dial the code string **03**OLD*NEW*NEW# (the old password and NEW is the new password only three digits long) and check that the mobile displays a response indicating that the new password has not been verified 2. Change the password using menu commands and check that the mobile displays a response indicating that the password has been changed
1. When attempted to dial the code strings for changing the password for Call Barring services, new password is entered only 3 digits long, the MS displays a response that the new password has not been verified 2. The MS displays a response that the new password has not been verified when attempted through menu commands as well
96
1. Dial the code string *03*330*OLD*NEW*NEW# (the old password and NEW is the new password only three digits long) and check that the mobile displays a response indicating that the new password has not been verified 2. Change the password using menu commands and check that the mobile displays a response indicating that the password has been changed
1. When attempted to dial the code strings for changing the password for Call Barring services, new password is entered only 3 digits long, the MS displays a response that the new password has not been verified 2. The MS displays a response that the new password has not been verified when attempted through menu commands as well
97
1. Call waiting service is Normal operation, Normal operation of Call activated on the MS waiting call indication Waiting 2. MS is on an active call
Arrange for an incoming call to be received. Ensure that call waiting indication (appropriate tone and The MS provides an appropriate tone and display) occurs. Clear the existing call and ensure display, and allows the waiting call to be that the phone alerts after the first call was accepted. cleared, and that the waiting call can be accepted Arrange for an incoming call to be received. Ensure The MS provides an appropriate tone and that call waiting indication (appropriate tone and display, and allows the waiting call to be display) occurs. Place the existing call on hold and accepted. ensure that the waiting call can be accepted Arrange for an incoming call to be received. Ensure that call waiting indication (appropriate tone and The MS provides an appropriate tone and display) occurs. Have the distant party clear the display, and allows the waiting call to be existing call and ensure that the waiting call can be accepted. accepted
98
99
100
1. Dial the code string *43# and check that the Activation of Call Waiting mobile displays a response indicating that the 1. MS is in idle mode without reference to a service has been activated 2. Call waiting is not activated specific basic service 2. Repeat the procedure using menu commands instead
1. When attempted to dial the code strings for activating the Call Waiting service, the MS displays a response indicating that the service has been activated 2. The MS displays a response that the Call Waiting service has been activated when attempted through menu commands as well
101
Deactivation of Call Deactivation without Waiting without basic service reference to a specific basic service
1. Dial the code string #43# and check that the mobile displays a response indicating that the service has been deactivated 2. Repeat procedure 1, but using menu commands instead
1. When attempted to dial the code strings for deactivating the Call Waiting service, the MS displays a response indicating that the service has been deactivated 2. The MS displays a response that the Call Waiting service has been deactivated when attempted through menu commands as well
102
Call Hold
1. Using code 2SEND, place the call on hold, and then retrieve the call using code 1SEND. Check that The distant party hears the call go on hold the distant party heard the call go on hold 2. Check using menu commands as well 1. Using code DNSEND (where DN s the number called), place the call on hold and make a second call. Using code 2SEND place the active call on hold The two calls are alternated and conversation and retrieve the held call. Ensure that conversation is possible on the new call is possible on the new call 2. Check using menu commands as well Check that if the party on hold releases the call, the MS indicates that the call has ended Check that is the distant party releases the call during the attempt to retrieve it, the MS indicates that the call has ended Check that if distant party releases the active call, the held call can still be retrieved Dial the code 3 SEND to join the calls. Check that all three parties can speak to each other If the party on hold releases the call, the MS indicates that the call has ended. If the distant party releases the call during the attempt to retrieve it, the MS indicates that the call has ended If the distant party releases the active call, the held call can still be retrieved All parties can speak to each other
103
104 105 106 107 Multi Party MultiParty call handling MS is active on one call and has one call on hold
108
After completing procedure 1, arrange for a further incoming call to be made. Check that the call is An additional incoming call can join the indicated, and then answer it, placing the multiparty call already in progress multiparty call on hold (code 2 SEND). Check that conversation is possible on the new call. After completing procedure 2, dial the code 3 SEND to join the calls. Check that all four parties can speak to each other. After completing procedure 3, place the multiparty call on hold, and make a new outgoing call (DN SEND). Check that conversation is possible on the new call. After completing procedure 4, place the new call on hold, and retrieve the multiparty call (2 SEND). Check that conversation is possible between all parties of the multiparty call. After completing procedure 5, dial the code 3 SEND to join the calls. Check that all five parties can speak to each other. After completing procedure 6, place the multiparty call on hold, and make a new outgoing call (DN SEND). After completing procedure 7, dial the code 3 SEND to join the calls. Check that all six parties can speak to each other After completing procedure 8, arrange for a new incoming call to be made, place the multiparty on hold, and accept the new incoming call (2 SEND). All parties can speak to each other
109
110
Keeping the current multiparty call on hold, another outgoing call can be placed
111
Keeping the new call on hold, the previous mulitparty call can be retrieved
112
All parties can speak to each other Joining the new outgoing call to the previously placed mulitparty call All parties can speak to each other
113
114
115
Keeping the current multiparty call on hold, another incoming call can be accepted
116
After completing procedure 9, dial the code 3 When the number of participants has SEND to join the calls. Check that the attempt fails, exceeded 6, no new incoming/ outgoing call and that the mobile indicates that the maximum can be joined with the current multiparty call number of participants has been exceeded After completing procedure 10, create a private communication with one of the distant parties Private communication with one of the (Code 2X SEND), placing the remainder of the distant party is possible after placing the parties on hold. Check that conversation is possible remainder of the parties on hold with the chosen party, and that the correct party has been selected.
117
118
After completing procedure 11, make the distant party release the call during private conversation. Check that the call can be switched back to the multi party call (2 SEND).
Switch between the private party and the remainder parties is possible
119
After completing procedure 12, select another party for a private conversation (2X SEND) and During switching, if the private party ends the make this party release the call during the attempt call, then the multiparty call on hold should to switch to the private conversation. Check that be retrieved the call can be switched back to the multi party call (2 SEND). After completing procedure 13, have one of the distant parties clear the call. Ensure that the multiparty call is not disturbed for the remaining participants 1. MS is in idle mode Ensure that MS-initiated 2. MMI clock display is Idle mode MO USSD USSD operations are enabled carried out correctly. 3. SMS-CB is enabled If one of the distant parties ends the call, the remaining multiparty call should not disconnect
120
121
By means of appropriate MMI commands, invoke a USSD request invoked by means of USSD request. Check to see whether the network appropriate MMI commands should respond feature invoked responds as expected correctly USSD request containing at least 25 digits By means of appropriate MMI commands, invoke a when invoked by MMI commands should be USSD request containing atleast 25 digits sent successfully by the MS By means of appropriate MMI commands, invoke a USSD request that will invoke a network USSD request that will invoke a network request response containing 182 characters (including containing 182 characters (using 7-bit default 7-bit default alphabet) should be displayed alphabet) completely by the MS USSD request containing an international '+' By means of appropriate MMI commands, invoke a symbol should be sent by the MS in the USSD string containing an international + symbol correct sequence USSD request with the total number of By means of appropriate MMI commands, invoke a characters equalling (8n-1) and 7 spare bits at USSD string where the total number of characters the end should be correctly sent by the MS. to be sent equals (8n-1) and there are 7 spare bits The MS shall avoid confusing 7 binary zero at the end of the message pad bits as the @ character MS shall wait for the network's response and By means of appropriate MMI commands, invoke a shall avoid sending a Release Complete USSD request that will delay the network response message to the network when an USSD is about 60 seconds used that will delay the network response by 60 seconds
122
123
124
125
126
127
Correct operation of Procedure to check FDN activated on the MS FDN correct operation of FDN
1. Establish a non-FDN call then clear it. 2. Set the following conditions and attempt to establish a call for each condition: a. a number is stored in the ADN list b. a number is stored in the last number dialled list c. a number is stored in the missed call list d. a short message is stored which contains a directory number which can be extracted MS should only allow to call to the numbers from the message listed in the FDN list 3. Select the FDN option, verify PIN2, enable FDN and enter a valid number in FDN[1], where FDN[1] is not one of the numbers used in 1) or 2) above i.e. ADN, LND, Missed Call List and SMS number. Check that the MS indicates that FDN is active 4. Power MS off then on 5. Attempt to establish a call to the numbers used in 1) or 2) above. Check that the MS prevents the calls from being set up Access the FDN option, deactivate FDN and set up a call to the numbers used in 1) or 2) above. Check MS should allow to call any numbers that the MS permits the calls to be set up
128
129
Status report
Using MMI commands, set the Status Report in the MS. Send an MO SM with the Status Report 1.MS should support status Status report is returned by the network and parameter included. Check that the message report for a message delivery correctly received by the MS after the reaches its destination, and that the Status report 2. MS is in idle mode message reaches its destination is returned by the network and correctly received by the MS Using the MMI procedures defined by the manufacturer, create and send an SMS message of The message sent from the MS is correctly 160 characters. Check that it is correctly received received at its destination at its destination
130
Input SM (160 characters) when using MMI language of Default 7-bit alphabet
Ensure that an SMS 1. MS is in idle mode message of 160 2. MMI alphabet is set to characters can be stored default 7-bit coding and sent
131
Ensure that an SMS message longer than 160 characters can be stored and sent. Ensure that the Default 7-bit alphabet MS correctly displays the (over 160 characters) number of short messages which are sent. Ensure that the MS actually sends the indicated number of SMS Ensure that an SMS message longer than 160 characters can be stored and sentEnsure that the Extended default 7-bit MS correctly displays the alphabet (over 140 number of short Bytes) messages which are sent. Ensure that the MS actually sends the indicated number of SMS Ensure that an SMS message longer than 70 UCS-2 characters can be stored and sent. Ensure UCS-2 alphabet (over that the MS displays the 70 characters) number of short messages which are sent. Ensure that the MS actually sends the indicated number of SMS
1. MS is in idle mode 2. MMI alphabet is set to default 7-bit coding 3. MS supports SMS concatenation
Using the MMI procedures defined by the manufacturer, create and send concatenated SMS messages supporting the text (longer than 160 characters and max. capacity). Check the display if the number of sent messages is indicated and correct. Check that the SMS are correctly received at their destination, and that the entire text (longer than 160 characters and max. capacity) can be read without missing characters or redundancy
1. The MS indicates correctly how many messages are sent 2. The messages are correctly received at its destination and the entire text can be read without missing characters or redundancy
132
1. MS is in idle mode 2. MMI alphabet is set to default 7-bit coding 3. MS supports SMS concatenation
Using the MMI procedures defined by the manufacturer, create and send concatenated SMS messages supporting the text (longer than 140 Bytes and max. capacity). Check the display if the number of sent messages is indicated and correct. Check that the SMS are correctly received at their destination, and that the entire text (longer than 140 Bytes and max. capacity) can be read without missing characters or redundancy
1. The MS indicates correctly how many messages are sent 2. The messages are correctly received at its destination and the entire text can be read without missing characters or redundancy
133
Using the MMI procedures defined by the manufacturer, create and send concatenated SMS messages supporting the text (longer than 70 UCS1. MS is in idle mode 2 characters and max. capacity). Check the display 2. MMI alphabet is set to UCSif the number of sent messages is indicated and 2 character coding correct. Check that the SMS are correctly received 3. MS supports SMS at their destination, and that the entire text concatenation (longer than 70 UCS-2 characters and max. capacity) can be read without missing characters or redundancy
1. The MS indicates correctly how many messages are sent 2. The messages are correctly received at its destination and the entire text can be read without missing characters or redundancy
134
Ensure that an SMS During mobile in idle message can be received MS is in idle mode mode while the MS is in idle mode
Arrange for an SMS message (class 2) to be sent to The message is received and the contents are the MS. Check that the message is received and correctly displayed the contents are correctly displayed
135
Where the MS has an option to dial the originating number of an MS is in idle mode SM, ensure that the correct number is dialled
Arrange for an SMS message to be sent to the MS. By means of the MMI commands in the MS, call The SMS is received, and the correct number the originating number. Check that the correct is dialled number has been dialled Arrange for a Class 0 SM to be sent to the MS. By means of the MMI commands in the MS, display The SM is received but not stored, and not the SM and ensure that it has been correctly available after the MS is switched off and on received. Turn the MS off and on again, and check again that the SM is not in the message storage memory Arrange for a Class 1 SM to be sent to the MS. By means of the MMI commands in the MS, display the SM and ensure that it has been correctly received. Turn the MS off, and replace the SIM. Turn on the MS and check that the SM is still in the The SMS is received and stored in the MS mobile message storage memory. Place the original SIM in another MS and ensure that the message is not in the message storage memory on the new MS Arrange for a Class 2 SM to be sent to the MS. By means of the MMI commands in the MS, display the SM and ensure that it has been correctly received. Turn the MS off, and replace the SIM. The SMS is received and stored in the SIM Turn on the MS and check that the SM is not in the message store. Place the original SIM in another MS and ensure that the message is in the message store on the new MS Create a new MO-SM and attempt to store it on the SIM. Check that the MS responds with a SIM memory full indication and does not overwrite an existing message in the SIM Create a new MO-SM and store it on the SIM. Then delete it. Turn off the MS and turn it on again. Check that the SM is no longer stored The MS responds with a SIM memory full indication and does not overwrite an existing message in the SIM The SM is no longer stored on the SIM after being deleted
136
SM class 0 (accept and Ensure that a Class 0 SM displayed, but not is accepted and displayed MS is in idle mode stored) but not stored
137
Ensure that a Class 1 SM SM class 1 (storing in is accepted, displayed ME and displaying) and stored in the ME
MS is in idle mode
138
Ensure that a Class 2 SM SM class 2 (storing in is accepted, displayed SIM and displaying) and stored in the SIM
MS is in idle mode
139
Attempt to store a Store SM on the SIM; 1. MS is in idle mode message on the SIM when SIM memory 2. No memory space is when the SIM memory is full available on the SIM full Delete SM on the SIM Delete a message from the SIM MS is in idle mode
140
141
SM Validity Period
Using the MMI procedures defined by the manufacturer, enter a valid SM Validity Period. Send an SMS message to another MS. Check the Validity period in the SMSC or via the Status Report facility of the MS and/or the network. Ensure that The SMS message is not delivered the receiving MS remains turned off until after the SM Validity Period has expired. When turning on the receiving MS, ensure that the SMS message has not been delivered 1. Using the MMI procedures defined by the manufacturer, create and send an SMS message. If the mobile supports EMS all the supported EMS content type shall be tested. Ensure that the message is sent and is correctly received at its destination. 2. Repeat procedure 1, but with a Circuit Switched Data Call in progress. 3. Repeat procedure 1, but with a FAX Call in progress. 4. Repeat procedure 1, but with a GPRS Data Call in progress Using the MMI procedures defined by the manufacturer, create and send an SMS message. Move to an area with coverage. Ensure that the message is sent and is correctly received at its destination
142
During call
Ensure that an SMS message can be sent while the MS is engaged in a call
The message is sent and is correctly received at its destination when the MS has: 1. a Circuit-Switched Data Call in progress 2. a FAX Call in progress 3. a GPRS Data Call in progress
143
Ensure that an SMS message can be prepared while the MS is out of When out of coverage coverage, and that the MS is out of coverage area message is sent when the MS returns to the coverage area.
144
The incoming SM shall not cause the crash of the MS software even if it is 1. MS is in idle mode not supported or 2. There are atleast 2 free contains invalid locations in SM memory information in the standard or in the user data header fields
Arrange for all unsupported message type from the list below to be sent to the MS under test. Check that the message is received and the mobile software does not freeze. 8 bit encoded message UCS encoded message Concatenated messages NOKIA smart messages ALCATEL TDD messages SIEMENS OTA messages Messages that activate / deactivate fax, email, voice mail icons on the MS display WAP configuration messages
The software of the MS shall not freeze. If applicable the MS shall store the message. The MS may display the text content of the message. If forwarding generally supported the MS shall be able to forward the message
145
During call
Arrange for an SMS message (class 2) to be sent to the MS. If the mobile supports EMS all the supported EMS content type shall be included in the SM. Check that the message is received and Ensure that an SMS the contents are correctly displayed 1. MS is active on a voice call message can be received Repeat this test for the following conditions, if the 2. There is atleast 1 free while the MS is engaged features are supported location in SM memory in a call 1. When the MS is in the active state of a circuitswitched data call 2. When the MS is in the active state of a fax call. 3. When the MS is sending and receiving data using GPRS (active data transfer). Arrange for an SMS message to be sent to the MS. Check that the message is received and the alert is audible. Repeat this test for the following conditions, if the features are supported 1. When the MS is in the active state of a circuitswitched data call. 2. When the MS is sending and receiving data using GPRS.
The message is received and the contents are correctly displayed in each of the following cases: 1. MS is in the active state of a CircuitSwitched Data Call 2. MS is in the active state of a FAX Call 3. MS is in the active state of a GPRS Data Call
146
Where the MS can be configured to give an Acoustic signal, after 1. MS is in idle mode acoustic alert when an new short message 2. There is atleast 1 free SM is received, ensure (no Class) arrived location1 in SM memory that the alert does in fact occur.
The message is received and the alert is audible in each of the following cases: 1. MS is in the active state of a CircuitSwitched Data Call 2. MS is in the active state of a GPRS Data Call
147
Where the MS has an Call a number option to dial a number included in the text of included in the text of the MS is in idle mode the SM SM, ensure that the correct number is dialled.
Arrange for an SMS message to be sent to the MS. By means of the MMI commands in the MS, call the number included in the text of the SM. Check The correct number is dialled by the MS that the number which has been dialled was the right one presented by the MMI
148
Ensure that a type 0 short message is correctly received and acknowledged to the network. This means that: 1. the MS is able to receive the type 0 short message irrespective of 1. MS is in idle mode whether there is memory Short Message type 0 2. There is atleast 1 free available in the SIM or location1 in SM memory ME 2. the MS does not indicate the receipt of the type 0 short message to the user 3. the type 0 short message shall not be automatically stored in the SIM or ME.
Arrange for a type 0 SMS message to be sent to the MS. Check that the successful reception of the The message content shall be discarded but message is acknowledged to the network. Check the successful reception of the type 0 SM is that the MS does not indicate the receipt of this acknowledged to the network message to the user and that the message is not stored in the SIM or ME
149
Arrange for a type 0 SMS message to be sent to the MS. Check that the successful reception of the The message content shall be discarded but message is acknowledged to the network. Check the successful reception of the type 0 SM is that the MS does not indicate the receipt of this acknowledged to the network message to the user and that the message is not stored in the SIM or ME Using MMI commands, enter a new MO SM and store it without sending it. Remove the SIM from The MO SM is stored in the correct data field the MS and check the contents using a SIM reader in the SIM to ensure that the message is stored in the correct data field in the SIM Arrange to receive a Class 2 MT-SM. Using MMI commands, display the SM and check that it has been received correctly. Remove the SIM from the The MT SM is stored in the correct data field MS and check the contents using a SIM reader to in the SIM, with a correct indication of the ensure that the message is stored in the correct contents and status of the SM data field in the SIM, with a correct indication of the contents and status of the SM
150
Store MO-SM on the Ensure that an outgoing SIM and verify the SM is correctly stored on MS is in idle mode contents of the SM the SIM data fields on the SIM
151
Store MT-SM (read) on SIM and verify content of the SM data fields on the SIM
Ensure that a Class 2 MTSM that has been read is MS is in idle mode correctly stored on the SIM
152
Store MT-SM (unread) on SIM and verify contents of the SM data fields on the SIM
Ensure that a Class 2 MTSM that has not been MS is in idle mode read is correctly stored on the SIM
Arrange to receive a Class 2 MT-SM. Without displaying the SM, remove the SIM from the MS and check the contents using a SIM reader to ensure that the message is stored in the correct data field in the SIM, with a correct indication of the contents and status of the SM Arrange to receive a Class 2 MT-SM. Using MMI commands, display the SM and check that it has been received correctly, and then delete the SM. Remove the SIM from the MS and check the contents using a SIM reader to ensure that the message has been deleted and no longer remains on the SIM Using MMI commands, create a message containing all the characters of the extended default 7-bit alphabet (such as ^, ,, -, \, |, *, ~, +, ), and store the message. Retrieve the message and ensure that the characters are correctly displayed. The maximum depends on the combination of default and extended default 7-bit characters based on the following rule: N <= 140Bytes with N=2X+Y, (X: extended default 7-bit character, Y: default 7-bit character) can be written in one SMS Using MMI commands, send the message created in the previous test to another MS. Ensure that the message is correctly received, and that all the characters (such as ^, ,, -, \, |, *, ~, +, ) are correctly displayed, matching the characters entered. The maximum depends on the combination of default and extended default 7-bit characters based on the following rule: N <= 140Bytes with N=2X+Y, (X: extended default 7-bit character, Y: default 7-bit character) can be written in one SMS
The MT SM is stored in the correct data field in the SIM, with a correct indication of the contents and status of the SM
153
Ensure that a Class 2 MTDelete SM on the SIM SM that has been read and verify the and deleted is correctly MS is in idle mode contents of the SM removed from the SIM data fields on the SIM (to be checked by a SIM reader) Ensure that it is possible to include all the characters of the extended default 7-bit alphabet when creating a new SM, depending on MS is in idle mode which characters of the extended default alphabet are claimed to be supported by the mobile phone
154
Message storage
The extended default 7-bit characters (such as ^, ,, -, \, |, *, ~, +, ) are correctly displayed in the retrieved message
155
Ensure that all the characters of the extended default 7-bit Message transmission alphabet are correctly MS is in idle mode transmitted in an SM as claimed to be supported by the mobile phone
The message is correctly received, and all the characters extended default 7-bit characters (such as ^, ,, -, \, |, *, ~, +, ) are correctly displayed, matching the characters entered
156
Message reception
Ensure that all the characters of the extended default 7-bit alphabet are correctly received and displayed in an SM, depending on MS is in idle mode which characters of the extended default alphabet are claimed to be supported by the mobile phone Ensure that character counter increments/decrements correctly 2 digits when typing a SMS using an extended default 7-bit character
Arrange for an SM containing all the characters of the extended default 7-bit alphabet to be sent from another MS. Ensure that the message is correctly received, and that all the characters (such as ^, ,, -, \, |, *, ~, +, ) are correctly displayed, matching the characters entered
The message is correctly received, and all the characters extended default 7-bit characters (such as ^, ,, -, \, |, *, ~, +, ) are correctly displayed, matching the characters entered
157
Character Counter
MS is in idle mode
Write a SMS with at least one extended default 7bit character. The character counter should increment/decrement correctly by 2 digits per extended default 7-bit character. Check that the maximum of 80 extended default 7-bit characters can be written in one SMS
The counter will increment/decrement correctly when using extended default 7-bit characters and the maximum of 80 default 7bit characters can be written in one SMS
158
Message storage
Ensure that it is possible to include all the characters of the UCS-2 alphabet when creating a new SM, depending on MS is in idle mode which characters of the default alphabet are claimed to be supported by the mobile phone
Using MMI commands, create a message containing all the characters of the UCS-2 alphabet, The characters are correctly displayed in the and store the message. Retrieve the message and retrieved message ensure that the characters are correctly displayed
159
Ensure that all the characters of the UCS-2 alphabet are correctly Message transmission MS is in idle mode transmitted in an SM as claimed to be supported by the mobile phone
Using MMI commands send the message created in the previous test to another MS. Ensure that the The message is correctly received, and all the message is correctly received, and that all the characters are correctly displayed, matching characters are correctly displayed, matching the the characters entered characters entered
160
Message reception
Ensure that all the characters of the UCS-2 alphabet are correctly received and displayed in an SM, depending on MS is in idle mode which characters of the default alphabet are claimed to be supported by the mobile phone Ensure that character counter increments/decrements correctly when typing a SMS using a UCS-2 character
Arrange for an SM containing all the characters of the UCS-2 alphabet to be sent from another MS. The message is correctly received, and all the Ensure that the message is correctly received, and characters are correctly displayed, matching that all the characters are correctly displayed, the characters entered matching the characters entered
161
Character Counter
MS is in idle mode
Write a SMS with at least one UCS-2 character. The character counter should increment/decrement correctly. Check that the maximum of 70 UCS-2 characters can be written in one SMS
The counter will increment/decrement correctly when using UCS-2 characters and the maximum of 70 UCS-2 characters can be written in one SMS
Test case
20.3.1
Combined Attach The UE shall successfully and Detach; perform the combined attach Successful and detach procedures.
9.2.1
Ensure that the MS displays the GPRS service indication when it GPRS Service is attached to the GPRS Indication network and, if automatic (registered to the attach is supported, that the network) registration to the GPRS follows the GSM registration in an acceptable time
9.2.4
GSM and GPRS Verify that the MS handles the roaming allowed roaming procedure correctly
9.2.5
Verify that the MS behaves correctly when the PLMN rejects the GPRS attach procedure with the cause IMSI unknown in HLR (Reject Cause #11)
10
9.2.6
Verify that the MS correctly handles GPRS roaming not allowed in this PLMN (Reject Cause #14)
11
12
9.2.7
Verify that the MS correctly handles GPRS roaming not allowed (Reject Cause #7)
13
9.2.8
Verify that during power off and manual requests the MS performs correctly the operation of GPRS detach. Verify that after battery removal procedure the MS is able to register to the GPRS network
14
9.4.1
Verify that the MS performs MO PDP context correctly the PDP context activation for activation for WAP WAP application (test to be performed with and without PBCCH)
15
9.4.2
Verify that the MS performs MO PDP context correctly the PDP context activation for activation for Modem Modem applications application (test to be performed with and without PBCCH)
16
9.4.3
Two Verify that the MS performs simultaneous MO correctly the PDP context PDP context activation for WAP and Modem activations applications simultaneously
17
9.4.4
Verify the behaviour of the MS upon receipt of a modify PDP context request message (the trigger of this message depends on the network implementation)
18
9.5.1
Manual MO PDP Verify that the MS performs context correctly the manual PDP deactivation context deactivation procedure
19
9.5.2
Verify that the MS doesnt deactivate the PDP context by itself (without user action)
20
9.5.3
To verify that the MS performs Network initiated correctly the PDP context PDP context deactivation when it receives deactivation the appropriate network command
21
10.1.1
22
10.1.2
Stationary Verify the stability of EGPRS MS Downlink Data during downlink data transfer Transfer Stability
23
10.1.3
24
9.8.3.1
Reselection with no GPRS data transfer (Idle Mode Circuit Switched 2G Reselection Packet Attached (No PDPc))
25
9.8.3.2
Idle Mode Circuit Switched 2G Reselection Packet Attached (PDPc Active, No Data Transfer)
26
9.8.4.1
27
25.1.3.2
PIN1 handling
28
25.1.3.3
PIN2 handling
29
25.1.2.1
Procedure for testing support of Short message service parameters already stored on the UICC with USIM
30
25.1.2.2
Write SMSP (e.g. Procedure for testing support check correct of storing Short message storing of SMSP service parameters on the UICC parameters) with USIM Procedure for reading, storing Reading/ Writing/ and deleting of alpha identifiers Deleting ADNs and BCD numbers on the UICC with USIMs phone book MSISDN saved on Procedure for testing support USIM of MSISDN entries
31
25.1.4.1
32
25.3.2
33
25.4.2.1
Test the terminals with ICCs with SIM and UICCs with SIM but no USIM in 3G networks which allow the use of a SIM
34
43.1.1.1
Verification that the MS sends MMS Mobile correctly the message, when Originated with the international, the national different MSISDN and the short MSISDN address address formats formats are used
35
43.1.1.2
Send MMS when Verification that the MS the sender is correctly sends an anonymous anonymous MMS
36
43.1.1.3
Send message Verification that the MS with MSISDN correctly sends the message recipient using when one of the To , the Cc the To, the Cc or the Bcc address fields is or the Bcc field used
37
43.1.1.4
Send message Verification that the MS with email correctly sends the message recipient using when the To, the Cc or the the To, the Cc Bcc address field is used to or the Bcc field insert the email address format
38
43.1.1.5
39
43.1.1.6
Send message Verification that the MMS will with multiple and be sent, when a legacy user unsubscribed and an MMS unsubscribed user recipient is inserted as recipient
40
43.1.2.1
Verification that the maximum length of the subject field is correctly supported
41
43.1.2.2
Verification that the maximum length of the text field is correctly supported
42
43.1.2.3
43
43.1.2.4
Send message Verification that the polyphonic with polyphonic sound object MIDI is sound object correctly supported (MIDI)
44
43.1.2.5
45
43.1.2.6
46
43.1.2.7
47
43.1.2.8
48
43.1.2.9
Send message with WBMP Verification that WBMP images image (different are correctly supported sizes)
49
43.1.2.10
50
43.1.2.11
51
43.1.2.12
Verification that it is possible to Send message send a MMS with an attached with appointment appointment from the attached organizer
52
43.1.2.13
Verification that it is possible to send a MMS with an attached VNote from the organizer
53
43.1.2.14
Send message Verification that it is possible to with different send a MMS with different objects to email objects to an email client client
54
43.1.2.15
Verification that it is possible to send a MMS with an attached Business Card to an email client
55
43.1.3.1
56
43.1.3.2
Verification that the MMS Send message priority is correctly supported with LOW priority by the MS
57
43.1.3.3
Verification that the MMS Send message priority is correctly supported with HIGH priority by the MS
58
43.1.4.1
Reply to message Verification that the MS with single correctly supports the reply to recipient a MMS with a single recipient
59
43.1.4.2
Reply to message Verification that the MS with multiple correctly supports the reply to recipients a MMS with multiple recipients
60
43.1.4.3
61
43.2.1.1
Verification that the MS correctly supports the MMS notification with indicated message size
62
43.2.1.2
Receive message Verification that the MS from MSISDN correctly supports the receiving sender using the of a MMS from a MSISDN To, the Cc or sender using the To, Cc or the Bcc field Bcc address field
63
43.2.1.3
Verification that the MS Receive message correctly supports the receiving from email client of a MMS from an email client
64
43.2.1.4
Receive message Verification that the MS to multiple correctly supports the receiving recipients using of a MMS with multiple the fields To, recipients using the fields To, Cc and Bcc Cc and Bcc
65
43.2.2.1
Receive message Verification that the MS with subject correctly supports the receiving (maximum of a MMS containing a subject length) with maximum length
66
43.2.2.2
Receive message Verification that the MS with text correctly supports the receiving (maximum of a MMS containing a text length) with maximum length
67
43.2.2.3
Verification that the MS Receive message correctly supports the receiving with sound object of a MMS containing an (iMelody) iMelody sound object
68
43.2.2.4
Receive message Verification that the MS with polyphonic correctly supports the receiving sound object of a MMS containing a MIDI (MIDI) sound object
69
43.2.2.5
Verification that the MS Receive message correctly supports the receiving with AMR sound of a MMS containing an AMR object sound object
70
43.2.2.6
Verification that the MS Receive message correctly supports the receiving with GIF image of a MMS containing a GIF (different sizes) image
71
43.2.2.7
Receive message Verification that the MS with animated correctly supports the receiving GIF image of a MMS containing an (different sizes) animated GIF image
72
43.2.2.8
Verification that the MS Receive message correctly supports the receiving with JPEG image of a MMS containing a JPEG (different sizes) image
73
43.2.2.9
Receive message Verification that the MS with WBMP correctly supports the receiving image (different of a MMS containing a WBMP sizes) image
74
43.2.2.10
Verification that the MS Receive message correctly supports the receiving with different of a MMS containing different objects objects
75
43.2.2.11
Verification that the MS Receive message correctly supports the receiving with Business of a MMS containing a Business Card attached Card
76
43.2.2.12
Receive message Verification that the MS with an correctly supports the receiving appointment of a MMS containing an attached appointment
77
43.2.2.13
Receive message Verification that the MS with VNotes correctly supports the receiving attached of a MMS containing a Vnote
78
43.2.2.14
Receive message Verification that the MS with different correctly supports the receiving objects from of a MMS containing different email client objects from an email client
79
43.2.3.1
Verification that the MS Receive message correctly supports the receiving with NORMAL of a MMS with normal Priority priority
80
43.2.3.2
Verification that the MS Receive message correctly supports the receiving with LOW Priority of a MMS with low priority
81
43.2.3.3
Verification that the MS Receive message correctly supports the receiving with HIGH Priority of a MMS with high priority
82
43.2.3.4
Verification that when the Receive message profile Meeting or Silence with the MS is activated in the MS, it shall profile Meeting not automatically play a sound or silence object of a MMS and that the MS shall be mute
83
43.2.4.1
Verification that when Auto Receive MMS Download is set to Off in the when Auto MS, it shall be possible to reject Download is set the receiving of the MMS. The to Off / Reject MS shall not automatically MMS download the MMS
84
43.2.4.2
Receive MMS Verification that when Auto when Auto Download is set to Confirm in Download is set the MS, it shall be possible to to Confirm defer the receiving of the MMS
85
43.2.4.3
Verification that when Auto Download is set to On in the MS, the MMS is automatically downloaded by the MS
86
43.2.4.4
Verification that when Auto Receive MMS Download is set to On in the when Auto MS and the MS memory is full, Download is set the download of the MMS is to On and the automatically deferred by the MS memory is full MS and an appropriate notification is given to the user
87
43.2.4.5
Receive MMS when Auto Download is set to On and the sender is anonymous
Verification that when Auto Download is set to On in the MS and the sender is anonymous, it is possible to deny the MMS
88
43.2.4.6
Verification that when Auto Download is set to Off in the MS, it is possible to download the MMS at a later time
89
43.3.1.1
Verification that the MS correctly supports indicating the Delivery Report request to the network
90
43.3.1.2
Verification that the MS correctly supports indicating the Delivery Report request to the network
91
43.3.1.3
Verification that the MS correctly supports the receipt of the MMS Delivery Report
92
43.3.1.4
Verification that the MS correctly supports the receipt of the MMS Delivery Report
93
43.3.1.5
Verification that the MS correctly supports the receipt of the MMS Delivery Report
94
43.3.1.6
Receive a Delivery Report when the MMS was sent to multiple recipients
Verification that the MS correctly supports the receipt of the MMS Delivery Report
95
43.3.1.7
Receive a Delivery Report when the Verification that the MS recipient MSISDN correctly supports the receipt is directly of the MMS Delivery Report forwarded to a different MSISDN
96
43.3.1.8
Verification that the MS correctly supports the deny of the MMS Delivery Report
97
43.3.2.1
Sending a Verification that the MS Message with correctly supports indicating Read Reply set to the Read Reply Report request On to the network
98
43.3.2.2
Sending a Verification that the MS Message with correctly supports indicating Read Reply set to the Read Reply Report request Off to the network
99
49.1.1.1
Send E-Mail with Verification that the MS email recipient correctly sends the message using the To, when the To, the Cc or the the Cc or the Bcc address field is used to Bcc field insert the email address format
100
49.1.1.2
Send E-Mail with Verification that it is possible to multiple send an e-mail message to recipients more than one recipient
101
49.1.1.3
Send E-Mail to an Verification that the e-mail will address book be sent to an address book recipient recipient
102
49.1.2.1
Send E-Mail with Verification that the maximum subject length of the subject field is (maximum correctly supported length)
103
49.1.2.2
Send E-Mail with Verification that the maximum text (maximum length of the text field is length) correctly supported
104
49.1.2.3
Send E-Mail with different objects Verification that the object (iMelody / MIDI / iMelody / MIDI / AMR sound / AMR sound / GIF GIF / Animated GIF / JPEG / / Animated GIF / WBMP with max. size is JPEG / WBMP correctly supported max. size)
105
49.1.2.4
106
49.1.2.5
Send E-Mail with Verification that it is possible to Business Card send an E-Mail with an attached attached Business Card
107
49.1.2.6
Verification that it is possible to Send message send a e-mail with an attached with appointment appointment from the attached organizer
108
49.1.2.7
Verification that it is possible to Send e-mail with send an e-mail with an VNotes attached attached VNote from the organizer
109
49.1.2.8
Send E-Mail with Verification that an e-mail with too long mail too long e-mail address address recipient recipient (exceeding 255 (exceed 255 characters) could not be sent characters)
110
49.1.3.1
Send E-Mail with Verification that the e-mail NORMAL / LOW / priority is correctly supported LOWEST / HIGH / by the MS HIGHEST / priority
111
49.5.1
E-Mail Setting with POP3 protocol E-Mail Setting with IMAP4 protocol
Verification that E-Mail settings with POP3 protocol works properly Verification that E-Mail settings with IMAP4 protocol works properly
112
49.5.2
113
49.4.2.1
Verification that it is possible to receive a Voice Call during the download session for e-mail without losing the e-mail notification
114
49.4.2.2
Verification that it is possible to receive a Short Message (CS mode) during the download session for e-mail without losing the e-mail notification
115
49.4.2.3
Incoming E-Mail Verification that it is possible to during an active receive an e-mail notification call during an active call
116
49.4.2.4
117
20.6.4
Manual Mode
If in manual network selection mode, the UE shall list all available PLMNs. This behaviour is independent from the content of the preferred PLMN list
118
20.6.5
The UE shall be retain its Selection mode configuration of automatic and following switch manual network selection off modes when switched off
Initial Configuration
Test Steps
1. Power on the MS 2. Verify that the MS sends a combined ATTACH REQUEST to the network 3. Check that in the ATTACH REQUEST message, the Attach type parameter 1. MS is powered OFF holds the Combined GPRS / IMSI 2. Its the first time the handset attach value attaches on the network, previously it 4. Check that in the ATTACH ACCEPT was on some other network message, the Attach result parameter holds the Combined GPRS / IMSI attached value 5. Check that in the ATTACH REQUEST message the type of identity parameter holds the IMSI value
1. MS is powered OFF 2. Its not the first time the handset attaches on the network
1. Power on the MS 2. Verify that the MS sends a combined ATTACH REQUEST to the network 3. Check that in the ATTACH REQUEST message, the Attach type parameter holds the Combined GPRS / IMSI attach value 4. Check that in the ATTACH ACCEPT message, the Attach result parameter holds the Combined GPRS / IMSI attached value 5. Check that in the ATTACH REQUEST message the type of identity parameter holds the TMSI/ P-TMSI value 6. If the ATTACH ACCEPT contained a new TMSI/P-TMSI value, then verify that the UE acknowledges this message by sending an ATTACH COMPLETE. Otherwise, no ATTACH COMPLETE shall be sent
MS is powered ON
Power off the MS and verify that the UE sends a DETACH REQUEST that in the DETACH REQUEST message, the Detach type parameter holds the power switched off, combined GPRS / IMSI detach value. If the detach is not done at power off, the Detach type parameter will hold the normal, combined GPRS / IMSI detach value and the network will answer back to the DETACH REQUEST with a DETACH ACCEPT message
1. MS is switched OFF 2. MS has a valid IMSI 3. The GPRS attach is performed automatically at power ON
1. Switch on the MS. The MS perform the IMSI ATTACH then the GPRS ATTACH 2. Observe the elapsed time between the GSM attach and the GPRS one (it must be only few seconds) 3. Verify that the GPRS registration status is indicated on the display 1. Switch on the MS. The MS perform the IMSI ATTACH 2. Launch the WAP browser, ensure that the operation is successful than quit the browser 3. Verify that the GPRS registration status is indicated on the display 1. Switch on the MS. The MS perform the IMSI ATTACH 2. Perform the manual ATTACH through the use of the appropriate AT command (+CGATT) and make sure that the MS executes correctly the requested operation 3. Verify that the GPRS registration status is indicated on the display Switch on the MS in a roaming network. The MS should perform IMSI and GPRS attach
1. MS is switched OFF 2. MS has a valid IMSI 3. The GPRS attach is performed only upon service request i.e. for the establishment of a PDP context and the MS remains attached after PDP context deactivation
1. MS is switched OFF 2. MS has a valid IMSI 3. The GPRS attach is not automatic
1. MS is switched OFF 2. SIM without a valid IMSI 3. Automatic Attach is enabled on the MS
1. Activate the MS and perform a GPRS attach 2. Note the display and error message displayed 3. Power cycle the MS
1. Activate the MS and perform a GPRS 1. MS is in idle mode attach 2. SIM without a valid IMSI 2. Note the display and error message 3. Manual Attach is enabled on the MS displayed 3. Power cycle the MS 1. The MS is powered on in the HOME PLMN and performs IMSI attach (GSM 1. MS is switched OFF attach successful) and GPRS attach 2. SIM with a valid IMSI in the roaming (GPRS attach successful) network 2. The MS is moved to the VISITED 3. GSM Roaming is enabled in the PLMN and shall attempt to register to visited PLMN the VISITED SGSN (GPRS attach does 4. GPRS roaming is not enabled not succeed) 5. Automatic Attach is enabled on the 3. The MS is moved back to the HOME MS PLMN and shall attempt the GPRS attach (GPRS attach successful)
1. The MS is powered on in the HOME PLMN and performs IMSI attach (GSM 1. MS is in idle mode attach successful) and GPRS attach 2. SIM with a valid IMSI in the roaming (GPRS attach successful) network 2. The MS is moved to the VISITED 3. GSM Roaming is enabled in the PLMN and shall attempt to register to visited PLMN the VISITED SGSN (GPRS attach does 4. GPRS roaming is not enabled not succeed) 5. Manual Attach is enabled on the MS 3. The MS is moved back to the HOME PLMN and shall attempt the GPRS attach (GPRS attach successful)
1. The MS is powered on in the HOME PLMN and performs IMSI attach (GSM attach successful) and GPRS attach 1. MS is switched OFF (GPRS attach successful) 2. SIM with a valid IMSI in the roaming 2. The MS is moved to the VISITED network PLMN and shall attempt to register to 3. GSM Roaming is enabled in the the VISITED SGSN (GPRS attach does visited PLMN not succeed) 4. GPRS roaming is not enabled in the 3. The MS is moved back to the HOME VPLMN PLMN and shall not attempt the GPRS 5. Automatic Attach is enabled on the attach MS 4. The MS is powered off then on. The MS shall perform GSM and GPRS attach successfully
1. GPRS detach normal (at power off) 2. GPRS detach normal (after leaving the WAP browser, if this procedure is foreseen for the MS under test) 3. GPRS detach while PDP context activated (through AT command) 4. GPRS detach while PDP context activated (battery removal), GPRS attach. Verify that the MS is able to perform the attach procedure correctly 5. GPRS detach while transfer being performed (through AT command). 6. GPRS detach while transfer being performed (battery removal), GPRS attach
After the GPRS attach try to connect to the WAP network using the WAP browser of the MS
Verify that the MS performs correctly all the operation related to the PDP context activation for modem application with specified APN. Particularly verify the following case: 1. different APN 2. different QoS (try to change the QoS and analyze if the MS can support it): The test shall be done changing the reliability class from 3 to 2 1. Activate the first PDP context for WAP application and try to browse in the WAP network 2. During this operation try to establish a WEB connection. The MS must be able to manage the two different PDP contexts. Ensure that no error message pass through the Gb interface
The user must activate a PDP context. A modify PDP context request message is then sent to the MS from the SGSN (the trigger of this message depends on the network implementation) with a QoS that is acceptable to the MS
Verify that the MS can do, after manual commands, the PDP context deactivation. Particularly its important to verify the following cases: 1. Manual MO PDP context deactivation/activation cycle (10s between deactivation and activation) 2. Manual PDP context deactivation/activation cycle (10s between deactivation and activation) while transfer being performed
During several WAP, WEB or FTP session, the MS should not deactivate the PDP context by itself (PDP context should stay active for at least 20min) If the network sends the PDP context deactivation to the MS, it must perform correctly all the operation related to this command
1. MS is GPRS and IMSI attached 2. MS is used in tethered mode as a modem for laptop 3. The strong, medium and weak signal areas are identified
1. Activate PDP Context 2. Use DOS FTP to download a 1MB file. If possible, utilize a server with minimal latency to the GGSN. 3. Repeat the file download 5 times, record the average throughput
1. MS is GPRS and IMSI attached 2. MS is used in tethered mode as a modem for laptop 3. The medium signal areas are identified
1. Activate PDP Context 2. Use DOS FTP to download a 15MB file. 3. After download is complete, start a web browser and go to a few sites 4. Repeat steps 1-3 three times 1. Activate PDP Context 2. Use DOS FTP to upload a 1MB file. If possible, utilize a server with minimal latency to the GGSN. 3. Repeat the file upload 5 times, record the average throughput 4. If extended dynamic allocation is supported, take MS log to verify uplink TS usage and peak/average uplink throughput
1. MS is GPRS and IMSI attached 2. MS is used in tethered mode as a modem for laptop 3. The medium signal areas are identified
Move between the coverage areas of different cells, ideally on a long test route covering the following scenarios: 1. Between cells sharing a LAI and RAI 2. Between cells sharing a LAI but not 1. There must be an appropriate sharing RAI number of 2G cells available on the 3. Between cells not sharing a LAI same PLMN 4. Between cells belonging to the same 2. The device should be in idle mode BSC 3. The device should be IMSI attached, 5. Between cells belonging to different and Packet attached but with no PDP BSCs context 6. Between cells utilising the same GSM frequency band 7. Between cells belonging to differerent GSM frequency bands 8. In areas of poor signal strength
Move between the coverage areas of different cells, ideally on a long test route covering the following scenarios: 1. There must be an appropriate 1. Between cells sharing a LAI and RAI number of 2G cells available on the 2. Between cells sharing a LAI but not same PLMN sharing RAI 2. The device should be in idle mode 3. Between cells not sharing a LAI 3. The device should be IMSI attached, 4. Between cells utilising the same and Packet attached, with a PDP GSM frequency band context, but not transmitting any data 5. Between cells belonging to differerent GSM frequency bands 6. In areas of poor signal strength
Move between the coverage areas of different cells, ideally on a long test route covering the following scenarios: 1. Between cells sharing a LAI and RAI 1. There must be an appropriate 2. Between cells sharing a LAI but not number of 2G cells available on the sharing RAI same PLMN 3. Between cells not sharing a LAI 2. The device should be in idle mode 4. Between cells belonging to different 3. The device should be IMSI attached, BSCs and Packet attached with a PDP 5. Between cells utilising the same context active GSM frequency band 6. Between cells belonging to differerent GSM frequency bands 7. In areas of poor signal strength
MS is in idle mode
1. Change of PIN1 2. Change of PIN1, wrong repeating of new PIN1 3. Change of PIN1, old PIN1 wrong 4. Change of PIN1, new PIN1 wrong (3 digits long) 5. Deactivation of PIN1 6. Change of PIN1, when deactivated 7. Activation of PIN1 8. Change of PIN1, when blocked 9. Unblocking of blocked PIN1 1. Change of PIN2 2. Change of PIN2, wrong repeating of new PIN2 3. Change of PIN2, old PIN2 wrong 4. Change of PIN2, new PIN2 wrong (3 digits long) 5. Change of PIN2, when blocked 6. Unblocking of blocked PIN2
MS is in idle mode
SMSP is available
SMSP is available
MS is in idle mode
1. Storage of directory number and name 2. Storage of international number ('+') 3. Storage of SSC string (including international number: '**21*+49DN#' 4 Change directory number and name 5. Storage of SIM Data after Location Update accept 6. MCC, MNC deleted from forbidden PLMN list 7. Storage of SIM Data after LUP reject; IMSI unknown in HLR 8. Storage of SIM Data after LUP reject; Authentication error 9. Storage of SIM Data after LUP reject; PLMN not allowed 10. Storage in forbidden PLMN list without loss of information in list 11. Storage of SIM Data after LUP reject; LA not allowed
MS is in idle mode
1. Create a new MMS message, add a MSISDN recipient with the national MSISDN address format (for example: 0172 123456...). Then send the message. The MS displays a message that the MMS has been sent. Verify that the message is correctly received by the B-subscriber 2. Repeat the test using the international MSISDN address format (for example: +49 172 123456...) 3. Repeat the test using the short MSISDN address format (for example: 1234) Create a new MMS and select from the menu option send as anonymous. Then send the message. The MS displays a message that the MMS has been sent. Verify that the message will be received and the senders address is not visible 1. Create a new MMS message, add a MSISDN recipient only to the To address field. Send the message. The MS displays a message that the MMS has been sent. Verify that the message is correctly received by the Bsubscriber 2. Repeat the test using only the Cc address field 3. Repeat the test using only the Bcc address field
MS is in idle mode
MS is in idle mode
MS is in idle mode
1. Create a new MMS with a text, picture and sound object, then add an email recipient to the To address field. Then send the MMS. The MS displays a message that the MMS has been sent. Verify that the email recipient receives the message and that the address fields and the email body are correctly used 2. Repeat the test using the Cc address field 3. Repeat the test using the Bcc address field Create a new MMS with a text, picture and sound object, add 20 recipients from the phonebook, using both email and phone number address format. Use all three address fields (To, Cc, and Bcc). Send the MMS. The MS displays a message that the MMS has been sent. Verify that the MMS recipients receive the message and that the MMS / email is correctly received
MS is in idle mode
Create a new MMS with a text, picture and sound object, add some recipients from the phonebook. Use all three address fields (To, Cc, and Bcc). Add at least one legacy and one MMS unsubscribed recipient. Send the MMS. For the unsubscribed user the MS displays a message that the Recipient is not subscribed. For the valid recipients the MS displays a message that the MMS has been sent. Verify that the valid MMS recipients receive the message and that the MMS is correctly received
MS is in idle mode
Create a new MMS and insert a text object. Fill the subject field with the maximum length of 40 characters. Send the message. The MS displays a message that the MMS has been sent. Verify that all characters of the subject are sent to the recipient Create a new MMS and insert a text object. Fill the text object with the maximum length of 1000 characters. Send the message. The MS displays a message that the MMS has been sent. Verify that all characters of the text are sent to the recipient Create a new MMS and insert an iMelody sound object. Send the message. The MS displays a message that the MMS has been sent. Verify that the iMelody is played at the recipient while the MMS is viewed and that the sound between the two MSs is comparable
MS is in idle mode
Create a new MMS and insert a MIDI sound object. Send the message. The 1. MS is in idle mode MS displays a message that the MMS 2. MIDI available in the sound browser has been sent. Verify that the MIDI is of the MS played at the recipient while the MMS is viewed and that the sound between the two MSs is comparable
Create a new MMS and insert an AMR sound object. Send the message. The MS displays a message that the MMS has been sent. Verify that the sound is played at the recipient while the MMS is viewed and that the sound between the two MSs is comparable
1. Create a new MMS and insert a GIF image object. Send the message. The MS displays a message that the MMS has been sent. Verify that the image can displayed at the recipient while the MMS is viewed 2. Repeat the test using different GIF image sizes 1. Create a new MMS and insert an animated GIF image object. Send the message. The MS displays a message that the MMS has been sent. Verify that the image can displayed and that it is animated at the recipient while the MMS is viewed 2. Repeat the test using different animated GIF image sizes 1. Create a new MMS and insert a JPEG image object. Send the message. The MS displays a message that the MMS has been sent. Verify that the image can displayed at the recipient while the MMS is viewed 2. Repeat the test using different JPEG image sizes
1. MS is in idle mode 2. An animated GIF image available in the picture browser of the MS
1. Create a new MMS and insert a WBMP image object. Send the message. The MS displays a message 1. MS is in idle mode that the MMS has been sent. Verify 2. WBMP image available in the picture that the image can displayed at the browser of the MS recipient while the MMS is viewed 2. Repeat the test using different WBMP image sizes Create a new MMS and insert at least 2 different text, 2 different picture and 2 1. MS is in idle mode different sound objects. Send the 2. At least 2 different pictures and 2 message. The MS displays a message different sound objects available in the that the MMS has been sent. Verify MS that all objects are correctly available at the recipient while the MMS is viewed
Create a new MMS and attach a Business Card or add a contact from the phonebook as attachment. Send the message. The MS displays a message that the MMS has been sent. Verify that the Business Card can be displayed at the recipient while the MMS is viewed Create a new MMS and attach an appointment from the organizer. Send the message. The MS displays a message that the MMS has been sent. Verify that the appointment can be displayed at the recipient while the MMS is viewed Create a new MMS and attach a VNote from the organizer. Send the message. The MS displays a message that the MMS has been sent. Verify that the VNote can be displayed at the recipient while the MMS is viewed
1. MS is in idle mode 2. JPEG-, GIF-, WBMP-, AMR- and melody objects are available in the organiser of the MS
1. Create a new MMS with a text object. Send the message to an email recipient. The MS displays a message that the MMS has been sent. Verify that the email recipient receives the message and that the text object is embedded in the email. 2. Repeat the test with a JPEG object 3. Repeat the test with a GIF object 4. Repeat the test with a WBMP object 5. Repeat the test with an AMR sound object 6. Repeat the test with an iMelody object 7. Repeat the test with a MIDI object 8. Repeat the test with multiple pages and different objects
Create a new MMS and attach a Business Card. Send the message to an email client. The MS displays a message that the MMS has been sent. Verify that the Business Card is attached to email received by the recipient 1. Create a new MMS and set the priority to normal. Send the message. The MS displays a message that the MMS has been sent. Verify that the message received by the recipient has normal priority 2. Repeat the test using an email client as recipient 1. Create a new MMS and set the priority to low. Send the message. The MS displays a message that the MMS has been sent at low priority. Verify that the message received by the recipient has low priority. 2. Repeat the test using an email client as recipient 1. Create a new MMS and set the priority to high. Send the message. The MS displays a message that the MMS has been sent at high priority. Verify that the message received by the recipient has high priority 2. Repeat the test using an email client as recipient
MS is in idle mode
MS is in idle mode
MS is in idle mode
1. Create a new MMS by replying to one recipient having a MSISDN address. Send the message to an email client. The MS displays a message that 1. MS in idle mode the MMS has been sent. Verify that the 2. MS received MMS with various email message is received by the correct and MSISDN recipients in the To-, recipient Cc- and Bcc-address field in the 2. Repeat the test replying to one MMS message store recipient having an email address 3. Repeat the test replying to one recipient in the Cc address field 4. Repeat the test replying to one recipient in the Bcc address field
1. MS in idle mode 2. MS received MMS with various email and MSISDN recipients in the To-, Cc- and Bcc-address field in the MMS message store
Create a new MMS by replying to all recipients. Send the message. The MS displays a message that the MMS has been sent. Verify that the message is received by the previous sender and all recipients in the To-, Cc- and Bccaddress field 1. Receive a new MMS. Display the message and select the forwarding function. Enter a new recipient and send the message. Verify that the message will be received by the recipient and that the MMS is marked as being forwarded 2. Repeat the test forwarding the message to multiple recipients
1. Receive a MMS notification of a MMS. The MS shall indicate the MMS notification to the user. Verify that the message size is displayed in the MMS notification. Download the MMS and check whether the real message size of the MMS is the same as it was displayed in the notification 2. Repeat the test when having received several MMS notifications without downloading the MMSs. Verify that all individual MMS notifications are saved in the MS and that the individual MMS can be downloaded
MS is in idle mode
1. Receive a MMS from a MS where the To address field was used as MSISDN address format. The MS shall indicate the receipt of a new MMS. Open the received message. Verify that the sender and the message content is correctly displayed 2. Repeat the test receiving a MMS from a MS where the Cc address field was used as MSISDN address format 3. Repeat the test receiving a MMS from a MS where the Bcc address field was used as MSISDN address format Receive a MMS from an email client. The MS shall indicate the receipt of a new MMS. Open the received message. Verify that the sender and the message content is correctly displayed 1. Receive a MMS with multiple recipients in which the test recipient is addressed in the To address field. The MS shall indicate the receipt of a new MMS. Open the received message. Verify that the sender and the message content is correctly displayed 2. Repeat the test receiving a MMS with multiple recipients in which the test recipient is addressed in the Cc address field 3. Repeat the test receiving a MMS with multiple recipients in which the test recipient is addressed in the Bcc address field Receive a MMS containing a subject field with maximum length of 40 characters. The MS shall indicate the receipt of a new MMS. Open the received message. Verify that the subject field is complete and correctly displayed
MS is in idle mode
MS is in idle mode
MS is in idle mode
MS is in idle mode
Receive a MMS containing a text field with maximum length of 1000 characters. The MS shall indicate the receipt of a new MMS. Open the received message. Verify that the text field is complete and correctly displayed Receive a MMS containing an iMelody sound object. The MS shall indicate the receipt of a new MMS. Open the received message. Verify that the iMelody sound object is correctly played (i.e. that it is comparable to the sent iMelody) while viewing the MMS. Save the iMelody sound object to the designated data folder of the MS
MS is in idle mode
MS is in idle mode
Receive a MMS containing a MIDI sound object. The MS shall indicate the receipt of a new MMS. Open the received message. Verify that the MIDI sound object is correctly played (i.e. that it is comparable to the sent MIDI) while viewing the MMS. Save the MIDI sound object to the designated data folder of the MS Receive a MMS containing an AMR sound object. The MS shall indicate the receipt of a new MMS. Open the received message. Verify that the AMR sound object is correctly played while viewing the MMS. Save the AMR sound object to the designated data folder of the MS
MS is in idle mode
MS is in idle mode
1. Receive a MMS containing a GIF image. The MS shall indicate the receipt of a new MMS. Open the received message. Verify that the GIF image is correctly displayed while viewing the MMS. If the GIF image size is exceeding the screen size the MS shall either show a part of the image and provide a scroll option or fit the image to the display screen. Save the GIF image to the designated data folder of the MS 2. Repeat this test receiving a MMS with different GIF image sizes
MS is in idle mode
1. Receive a MMS containing an animated GIF image. The MS shall indicate the receipt of a new MMS. Open the received message. Verify that the animated GIF image is correctly displayed and animated while viewing the MMS. If the animated GIF image size is exceeding the screen size the MS shall either show a part of the image and provide a scroll option or fit the image to the display screen. Save the animated GIF image to the designated data folder of the MS 2. Repeat this test receiving a MMS with different animated GIF image sizes
MS is in idle mode
1. Receive a MMS containing a JPEG image. The MS shall indicate the receipt of a new MMS. Open the received message. Verify that the JPEG image is correctly displayed while viewing the MMS. If the JPEG image size is exceeding the screen size the MS shall either show a part of the image and provide a scroll option or fit the image to the display screen. Save the JPEG image to the designated data folder of the MS 2. Repeat this test receiving a MMS with different JPEG image sizes
MS is in idle mode
1. Receive a MMS containing a WBMP image. The MS shall indicate the receipt of a new MMS. Open the received message. Verify that the WBMP image is correctly displayed while viewing the MMS. If the WBMP image size is exceeding the screen size the MS shall either show a part of the image and provide a scroll option or fit the image to the display screen. Save the WBMP image to the designated data folder of the MS 2. Repeat this test receiving a MMS with different WBMP image sizes
MS is in idle mode
Receive a MMS containing at least 2 different text, 2 different picture and 2 different sound objects. The MS shall indicate the receipt of a new MMS. Open the received message. Verify that all objects are correctly available and can be played/displayed while viewing the MMS. Save the objects to their designated data folders of the MS
MS is in idle mode
Receive a MMS with a Business Card attached. The MS shall indicate the receipt of a new MMS. Open the received message. Verify that the Business Card is displayed when viewing the MMS. Save the Business Card to the directory of the MS Receive a MMS containing an appointment. The MS shall indicate the receipt of a new MMS. Open the received message. Verify that the appointment is displayed when viewing the MMS. Save the appointment to the organizer of the MS Receive a MMS containing a VNote. The MS shall indicate the receipt of a new MMS. Open the received message. Verify that the VNote is displayed when viewing the MMS. Save the VNote to the organizer of the MS
MS is in idle mode
MS is in idle mode
MS is in idle mode
1. Receive a MMS containing a text object from an email client. The MS shall indicate the receipt of a new MMS. Open the received message. Verify that the object is played/displayed when viewing the MMS. Save the object(s) to its/their designated data folder(s) of the MS 2. Repeat the test with a JPEG object 3. Repeat the test with a GIF object 4. Repeat the test with a WBMP object 5. Repeat the test with an AMR sound object 6. Repeat the test with an iMelody object 7. Repeat the test with a MIDI object 8. Repeat the test with multiple pages and different objects
MS is in idle mode
1. Receive a MMS with the priority set to normal. The MS shall indicate the receipt of a new MMS. Open the received message. Verify that the MMS is indicating the priority set to normal 2. Repeat the test receiving the MMS from an email client 1. Receive a MMS with the priority set to low. The MS shall indicate the receipt of a new MMS. Open the received message. Verify that the MMS is indicating the priority set to low 2. Repeat the test receiving the MMS from an email client 1. Receive a MMS with the priority set to high. The MS shall indicate the receipt of a new MMS. Open the received message. Verify that the MMS is indicating the priority set to high. 2. Repeat the test receiving the MMS from an email client
MS is in idle mode
MS is in idle mode
Receive a MMS containing a sound object. The MS shall indicate the receipt of a new MMS in silent/meeting mode. Open the received message. Verify that the MS is not automatically playing the sound object of the MMS and that the MS is mute
Receive a MMS notification of a MMS. The MS shall indicate the MMS notification to the user: 1. Verify that the MS is not automatically downloading the MMS. Reject the receiving of the MMS 2. Verify that the MS sends a M_Notify_Resp with X-MMS-Status set to reject to the network 3. Verify that the MS does not send a new notification for this message to the user
Receive a MMS notification of a MMS. The MS shall indicate the MMS notification to the user: 1. Verify that the MS is not automatically downloading the MMS. Defer the receiving of the MMS 2. Verify that the MS sends a defer message to the network. Download the deferred message from the server. Open the message and verify that the downloaded message is exactly the one which was previously deferred
Receive a MMS notification of a MMS. The MS shall indicate the MMS notification to the user. Verify that the MS is automatically downloading the MMS and after receipt, the message can be displayed by the user
Receive a MMS notification of a MMS. The MS shall indicate that a new MMS is available to the user but that there is not enough memory in the MS to receive the message. Verify that the 1. MS is in idle mode MS sends a defer message to the 2. Auto Download is set to On, MMS network. Clear the memory of the MS, memory of the MS is full then download the deferred message from the server. Open the message and verify that the downloaded message is exactly the one which was previously deferred Receive a MMS notification of a MMS. The MS shall indicate that a new MMS is available to the user but that the sender is anonymous. Verify that the MS is not automatically downloading the MMS Receive a MMS notification of a MMS. The MS shall indicate that a new MMS is available to the user. Verify that the MS is not automatically downloading the MMS but sending a defer message to the network. Download the deferred message from the server. Open the message and verify that the downloaded message is exactly the one which was previously deferred Create a new MMS. Send the message using an MSISDN in national format. The MS displays a message that the MMS has been sent. Ensure that the recipient has successfully received the MMS. Verify that the Delivery Report is sent back to the sender of the MMS. Verify that the MS correctly displays the Delivery Report
1. MS is in idle mode 2. Auto Download is set to On, Receive option is set to Deny message when anonymous sender
Create a new MMS. Send the message using an MSISDN in national format. The MS displays a message that the 1. MS is in idle mode MMS has been sent. Ensure that the 2. Delivery report is set to Off in the recipient has successfully received the MS MMS. Verify that the Delivery Report is sent back to the sender of the MMS. Verify that the MS correctly displays the Delivery Report Create a new MMS. Send the message. The MS displays a message that the MMS has been sent. Ensure that the recipient has successfully received the MMS. Verify that the Delivery Report is received by the sender of the MMS. Verify that the MS correctly indicates the status of the sent message as delivered Create a new MMS. Send the message. The MS displays a message that the MMS has been sent. Ensure that the recipient rejects the MMS. Verify that the Delivery Report is received by the sender of the MMS. Verify that the MS correctly indicates the status of the sent message as rejected
Create a new MMS. Send the message. The MS displays a message that the MMS has been sent. Ensure that the recipient does not receive the MMS and that the MMS delivery timer expires. Verify that then the Delivery Report is received by the sender of the MMS. Verify that the MS correctly indicates the status of the sent message as Timer expired
Create a new MMS to multiple recipients. Send the message. The MS displays a message that the MMS has been sent. Ensure that some recipients reject, defer of retrieve the message. Verify that for each recipient the Delivery Report is received by the sender of the MMS. Verify that the MS correctly indicates the various states of the sent message
Create a new MMS to multiple recipients. Send the message. The MS displays a message that the MMS has 1. MS is in idle mode been sent. Ensure that the recipient 2. Delivery Report is set to On in the has retrieved the MMS from the MS forwarded MSISDN. Verify that the 3. Recipient has enabled Directly Delivery Report is received by the Forwarding to another MSISDN sender of the MMS. Verify that the MS correctly indicates the status of the sent message as delivered 1. MS is in idle mode 2. Delivery report is set to On in the sending MS 3. Deny Delivery Report is set to on in the retrieving MS Retrieve a MMS and verify that the sending MS will not receive a Delivery Report
Create a new MMS. Send the message to an MSISDN in national format. The MS displays a message that the MMS has been sent. Ensure that the recipient has successfully received the MMS. When the recipient has read the message, verify that the Read Reply Report is sent back to the sender of the MMS. Verify that the MS correctly displays the Read Reply Report
Create a new MMS. Send the message. The MS displays a message that the MMS has been sent. Ensure that the recipient has successfully received the MMS. When the recipient has read the message, verify that no Read Reply Report is sent back to the sender of the MMS 1. Create a new E-Mail message with a text, then add an email recipient to the To address field. Then send the email. The MS displays a message that the e-mail has been sent. Verify that the email recipient receives the message and that the address fields and the email body are correctly used 2. Repeat the test using the Cc address field 3. Repeat the test using the Bcc address field
MS is in idle mode
MS is in idle mode
Create a new e-mail message with a text, add 20 different recipients, using the e-mail format recipients. Use all three address fields (To, Cc, and Bcc). Send the e-mail message. The MS displays a message that the e-mail has been sent. Verify that the e-mail recipients receive the message and that the email is correctly received
Create a new e-mail message with a text, add recipients that already exist in the phone address book (as e-mail recipients). Use all three address fields (To, Cc, and Bcc). Send the e-mail. For the valid existing address book recipients the MS displays a message that the e-mail has been sent
MS is in idle mode
Create a new E-Mail and insert a text object. Fill the subject field with the maximum length of 40 characters. Send the message. The MS displays a message that the e-mail has been sent. Verify that all characters of the subject are sent to the recipient Create a new e-mail and insert a text object. Fill the text object with the maximum length as defined by the vendor of terminal. Send the message. The MS displays a message that the email has been sent. Verify that all characters of the text are sent to the recipient 1. Create a new e-mail and insert an iMelody sound object. Send the message. The MS displays a message that the e-mail has been sent. Verify that the iMelody is played at the recipient while the e-mail is viewed and that the sound between the two MSs is comparable 2. Repeat this test process for the other objects: MIDI / AMR sound / GIF / Animated GIF / JPEG / WBMP
MS is in idle mode
Create a new e-mail and insert at least 2 different text, 2 different picture and 1. MS is in idle mode 2 different sound objects. Send the 2. At least 2 different pictures and 2 message. The MS displays a message different sound objects available in the that the e-mail has been sent. Verify MS that all objects are correctly available at the recipient while the e-mail is viewed Create a new e-mail and attach a Business Card or add a contact from the phonebook as attachment. Send the message. The MS displays a message that the e-mail has been sent. Verify that the Business Card can be displayed at the recipient while the email is viewed
Create a new e-mail and attach an appointment from the organizer. Send the message. The MS displays a message that the e-mail has been sent. Verify that the appointment can be displayed at the recipient while the email is viewed
Create a new e-mail and attach a VNote from the organizer. Send the 1. MS is in idle mode message. The MS displays a message 2. VNote is available in the organiser of that the e-mail has been sent. Verify the MS that the VNote can be displayed at the recipient while the e-mail is viewed Create a new e-mail and enter the too long e-mail address recipient 1. MS is in idle mode (exceeding 255 characters). Send the 2. Too long e-mail address recipient message. The MS displays a message (exceeding 255 characters) is available that the e-mail recipient has a too long address field and verify that the mail could not be sent 1. Create a new e-mail and set the priority to normal. Send the message. The MS displays a message that the e-mail has been sent. Verify that the message received by the recipient has normal priority 2. Repeat this test procedure with Low / Lowest / High / Highest priorities All related POP3 settings with the ISPs settings is set in the MS. After the settings are completed , try to send and receive an e-mail All related IMAP4 protocol settings with the ISPs settings is set in the MS. After the settings are completed , try to send and receive an e-mail
MS is in idle mode
1. MS with POP3 protocol settings is available 2. MS is in idle mode 1. MS with IMAP4 protocol settings is available 2. MS is in idle mode
Receive an e-mail and start to download the message. During the download session receive an incoming 1. MS is in idle mode Voice Call. Answer the call. The 2. Incoming CS calls during active GPRS download session shall be interrupted. session are supported by the network End the call and verify that the e-mail notification is still available and that it is possible to download the e-mail again Receive an e-mail and start to download the message. During the download session receive Short 1. MS is in idle mode Message on the CS channel. Read the 2. Incoming Short Message (CS) during Short Message. The download session active GPRS session is supported by the shall be interrupted. Verify that the enetwork mail notification is still available and that it is possible to download the email again 1. Perform a Voice Call. During the call receive an e-mail. When receiving the email notification, the call shall not be interrupted. End the call and verify that the notification of the e-mail is still available and that it is possible to download the e-mail 2. Repeat the test performing a CS Data Call Start a WAP session. While the WAP session is active, receive an e-mail. The MS shall save the e-mail notification while the WAP session is still active. Then check the e-mail notification and start to download the new e-mail. The MS shall close the active WAP session and start to connect to the e-mail browser to download the message. Verify that the e-mail is completely downloaded
MS is in a WAP session
1. Select the manual network selection mode on the UE and ensure that the list of all available PLMNs is displayed, and that the displayed networks can be selected, even if on the forbidden list UE switched on, in automatic selection 2. Check that the preferred PLMN list is mode in an area with coverage from not changed after the manual network both GSM and UMTS networks selection 3. Repeat the test with different entries in the preferred PLMN lists, including the empty list and lists of more than 32 entries 1. Change to manual network selection. Turn the UE off and on again. Check that the manual network selection mode is in use 2. Change to automatic network selection. Turn the UE off and on again. Check that the automatic network selection mode is in use
Expected Result
1. When powered ON, the MS sends a combined Attach Request to the network 2. The Attach Type parameter shall hold the value: Combined GPRS/ IMSI attach 3. In the Attach Accept message, the Attach Parameter shall hold the value: Combined GPRS/ IMSI attached
1. When powered ON, the MS sends a combined Attach Request to the network 2. The Attach Type parameter shall hold the value: TMSI/ P-TMSI 3. If the Attach Accept message contains a new TMSI/ P-TMSI value, the MS acknowledges this message by sending an Attach Complete message
1. When powered OFF, the MS sends a Detach Request message to the network 2. The Detach Type parameter holds the value: power switched off, combined GPRS/ IMSI detach 3. If the detach is not done at power OFF mode, the Detach Type parameter shall hold the value: normal, combined GPRS/ IMSI detach. The network responds back with a Detach Accept message 1. When powered ON, the MS performs the IMSI Attach 2. MS performs GPRS Attach after IMSI Attach 3. The elapsed time between GSM Attach and GPRS Attach should be only a few seconds 4. The GPRS registration status shall be indicated on the display 1. When powered ON, the MS performs the IMSI Attach 2. WAP Browser can be launched successfully and exited successfully 3. The GPRS registration status shall be indicated on the display
1. When powered ON, the MS performs the IMSI Attach 2. MS executes the manual attach through the use of appropriate AT commands (+CGATT) correctly 3. The GPRS registration status shall be indicated on the display
When switched ON, the MS shall successfully register to the roaming network and shall offer unrestricted GPRS functionality
1. When powered ON, the MS shall attempt to perform a GPRS attach, and shall display an appropriate error message 2. After power cycle, the MS shall reattempt GPRS attach 1. When powered ON, the MS shall attempt to perform a GPRS attach, and shall display an appropriate error message 2. After power cycle, the MS shall reattempt GPRS attach
1. When powered ON in the HPLMN, the MS performs IMSI Attach and GPRS Attach successfully 2. When moved from HPLMN to VPLMN, the MS attempts to register on the Visited SGSN but doesnt succeed 3. When moved back to the HPLMN, the MS shall successfully register and GPRS Attach should be successful
1. When powered ON in the HPLMN, the MS performs IMSI Attach and GPRS Attach successfully 2. When moved from HPLMN to VPLMN, the MS attempts to register on the Visited SGSN but doesnt succeed 3. When moved back to the HPLMN, the MS shall successfully register and GPRS Attach should be successful
1. When powered ON in the HPLMN, the MS performs IMSI Attach and GPRS Attach successfully 2. When moved from HPLMN to VPLMN, the MS attempts to register on the Visited SGSN but doesnt succeed 3. When moved back to the HPLMN, the MS shall not attempt GPRS Attach 4. After power cycle, the MS shall perform GSM and GPRS Attach successfully
1. When powered OFF, MS should initiate GPRS detach procedure 2. When leaving WAP browser, MS should initiate GPRS detach procedure 3. When PDP context is activated through AT commands 4. Battery is removed while the PDP context is active, GPRS detach shall occur correctly. And also after MS is powered ON, GPRS Attach shall occur correctly 5. While data transfer is in progress, and GPRS detach is activated with the help of AT commands 6. Battery is removed while the data transfer is in progress, GPRS detach shall occur correctly. And also after MS is powered ON, GPRS Attach shall occur correctly MS shall perform the PDP context activation correctly when attempted to connect to the WAP browser after GPRS attach
MS shall perform the PDP context activation correctly for Modem application with: 1. specified APN 2. different APN 3. different QoS
The MS must be able to manage the two different PDP contexts ensuring no error message pass through the air interface
When a modify PDP context request message is then sent to the MS from the SGSN, with a QoS that is acceptable to the MS, the MS shall send a "modify PDP context accept" message in return. If the QoS are not acceptable from the MS, it shall send a "Deactivate PDP context request" message in return
The MS shall perform the PDP context deactivation correctly: 1. during no file transfer 2. during file transfer
During several WAP, WEB or FTP session, the MS should not deactivate the PDP context by itself (PDP context should stay active for at least 20min) The MS performs correctly the PDP context deactivation when it receives the appropriate network command 1. The average throughput shall be at least: a. 40kbps per timeslot in strong signal area b. 25kbps per timeslot in medium signal area c. 15kbps per timeslot in weak signal area 2. The GPRS connection and file download shall be stable
1. The GPRS connection shall be stable 2. The file download shall complete
1. The average throughput shall be at least: a. 40kbps per timeslot in strong signal area b. 25kbps per timeslot in medium signal area c. 15kbps per timeslot in weak signal area 2. The GPRS connection and file download shall be stable
1. MS should perform reselections correctly, without losing service 2. MS should be able to receive calls before and after the reselections
1. MS should perform reselections correctly, without losing service 2. MS should be able to receive calls before and after the reselections
1. MS should perform reselections correctly, without losing service 2. Data transfer may pause during reselection but resume on the new cell 3. MS shall be able to receive calls after the reselections (which may pause data transfer without DTM) 4. The data session shall resume after releasing the voice call 5. The data rate shall be as expected for the data bearer type assigned by the network throughout the test, i.e. data rates proportional to the data bearer and signal quality shall be achieved both before and after the cell reselections
The message is sent and correctly received by the B-subscriber. The senders address is not visible
The message is correctly sent and received by the email recipient indicating the appropriate address fields
The message is correctly sent and received by all recipients indicating the appropriate address fields
The message is sent with the appropriate display messages and received by all valid recipients indicating the appropriate address fields
The message is correctly sent and received by the recipient with the complete subject field
The message is correctly sent and received by the recipient with the complete text field
The message is correctly sent and received by the recipient with the appropriate iMelody sound
The message is correctly sent and received by the recipient with the appropriate MIDI sound
The message is correctly sent and received by the recipient with the appropriate sound object
The message is correctly sent and received by the recipient with the correct GIF image
The message is correctly sent and received by the recipient with the correctly animated GIF image
The message is correctly sent and received by the recipient with the correct JPEG image
The message is correctly sent and received by the recipient with the correct WBMP image
The message is correctly sent and received by the recipient with all objects
The message is correctly sent and received by the recipient with the Business Card
The message is correctly sent and received by the recipient with the attached appointment
The message is correctly sent and received by the recipient with the attached Vnote
The message is correctly sent and received by the email recipient with the appropriate embedded objects
The message is correctly sent and received by the email recipient with the Business Card
The message is correctly sent and received by the recipient with the appropriate priority
The message is correctly sent and received by the recipient with the appropriate priority
The message is correctly sent and received by the recipient with the appropriate priority
The message is correctly forwarded and received by the recipient(s) with the forwarding marker
The Notification(s) are saved in the MS, its/their message size is correctly displayed and the correct MMS is downloaded
The iMelody sound object is correctly played and can be saved to the appropriate data folder of the MS
The MIDI sound object is correctly played and can be saved to the appropriate data folder of the MS
The AMR sound object is correctly played and can be saved to the appropriate data folder of the MS
The GIF image is correctly displayed and can be saved to the appropriate data folder of the MS
The animated GIF image is correctly displayed and animated and can be saved to the appropriate data folder of the MS
The JPEG image is correctly displayed and can be saved to the appropriate data folder of the MS
The WBMP image is correctly displayed and can be saved to the appropriate data folder of the MS
All objects can be played/displayed and can be saved to the appropriate data folders of the MS
The Business Card can be displayed and saved to the directory of the MS
The various objects can be played/displayed and saved to its/their designated data folder(s) of the MS
The MS is not automatically downloading the MMS. On reject by the user, the MS sends a M_Notify_Resp with X-MMS-Status set to reject to the network. The MS does not send a new notification for this message to the user
The MS is not automatically downloading the MMS. On defer by the user, the MS sends a defer message to the network. On downloading, the MS receives exactly the MMS which was previously deferred
The MS is automatically downloading the MMS. After receipt, the message can be displayed by the user
The MS is indicating to the user that its MMS memory is full. The MS sends a defer message to the network. On downloading, the MS receives exactly the MMS which was previously deferred
The MS is not automatically downloading the MMS. On receipt of the MMS notification, the MS sends a defer message to the network. On downloading, the MS receives exactly the MMS which was previously deferred
The MS is displaying the delivery status of the sent message as Timer expired
The MS is correctly displaying the various delivery states of the sent message
The retrieving MS is denying the Delivery Report and the sending MS is not receiving a Delivery Report
The message is correctly sent and received by the email recipient indicating the appropriate address fields
The message is correctly sent and received by all recipients indicating the appropriate address fields
The message is sent for all addressor recipients with the appropriate display messages and received by all valid address book recipients indicating the appropriate address fields
The message is correctly sent and received by the recipient with the complete subject field
The message is correctly sent and received by the recipient with the complete text field
The message is correctly sent and received by the recipient with the appropriate object
The message is correctly sent and received by the recipient with all objects
The message is correctly sent and received by the recipient with the Business Card
The message is correctly sent and received by the recipient with the attached appointment
The message is correctly sent and received by the recipient with the attached Vnote
The message could not be sent since the recipients mail address is too long
The message is correctly sent and received by the recipient with the appropriate priority
The MMS notification is still available and it is possible to download the MMS again
The e-mail notification is still available and it is possible to download the e-mail again
The call does not drop. The e-mail notification is still available and it is possible to download the e-mail
The e-mail notification is still available and it is possible to download the complete e-mail
The UE shall display all available PLMNs and it shall perform manual network selection on the chosen network. The preferred PLMN list is not changed after the manual network selection. The UE shall display all available GSM and UMTS networks
The UE has the same selection mode when switched on that it had when switched off