Académique Documents
Professionnel Documents
Culture Documents
BR1
BR2 BR2 BR2 BR2 BR2
Dihed. break
1/8" dowel
BR2
BR2 BR2
1/4 sq. LE
F5 1/16 balsa
F3 F4 1/16 balsa F5
Turtledeck bulkheads 1/16" balsa Turtledeck (5) stringers 1/16" sq. balsa
Dihed. break
BR1
BR1
BR1
1/16" ply over
1/8" light ply
BR2
BR2
BR2
F2
4
Foam and/or balsa machine guns
Rudder post & rudder LE 1/8 X 3/16" All rest of rudder & vertical stab wood is 1/8"
F3
F1
Foam block
1/16" dowel hatch holddown Dummy engine
F2a & b
Hatch Latch (Velcro )
Foam Pilot
Exhaust
All covering Litespan. Original done in all white Swiss trainer colors, with red Litespan Swiss markings laid over white. WARNING: Blue foam WILL show through white Litespan!!! Other color notes: Draw brown leather cockpit coaming on with marker.
BT1 1/8" sq. SPRUCE FORWARD spars 1/16" scrap (top only)
BT1
Sub-wing blue foam, carved & sanded to shape, then covered.
1/8 sq.
F2 - 1/16" ply
balsa triangles
LE
1/4" X 1/8" TE with 1/16" indented scalloping
1/16" X 1/8"
1/16" ply control horns 1/8" balsa (grain horizontal)
Bottom front
Bottom rear
Top front
Top rear
90 deg.
Elevate lower wing tip rib .54" PER PANEL, top wing tip rib .67" PER PANEL. Dihederal is 3 degrees PER PANEL, with centersection "flat", i.e., no dihed.
Speed controller goes along side motor. Batteries go vertically (I used 4 sets of two end-to-end pairs) right behind motor/motor mount. Receiver wrapped with foam, hangs from cabane strut 3 cross-brace (cable -tied).
and washers
5
Old window screen used to make radiator MUST be OPEN for cooling air intake!!!.
Servo bay
TT1
TR4 1/32" ply dih. braces TR3
TR6
TR6
TR3
TR1
TR2
TR2
R5a
R4a
required
1/8" + scrap
R4a
R5a
TR9 A2
S5
S4
TR5
TR7
TR8
1/8" X 1/4"
2. l 5 " w he e s Make wheels by sandwiching 1/8" light play between two layers of 1/8" balsa, then turn assembly to shape. I used bolt though wheel blank, chucked into drill, with hand-held X-acto knife CAREFULLY used as lathe blade
1/8" sq.
1/8" sq.
Fokker D-VII Speed 400 with Olympus gearbox 252 sq. inches 20-24 oz weight Drawn November, 1998 in DesignCAD 2D Rescued and converted to TurboCAD 2D June, 1999
1/8" X 1/4"
Drill holes in motor mount for Cabane 1, then CA in place during final assembly.
LG wire and
by small screws
Wing
Wing
Wing
Top
Wing
0.250
Wing
0.250
Wing
0.250
1.960
2.300
0.250
Front
Cabane 1 True length 5.03"
0.250
Wing
1.999
4.100
0.251 2.300
Side
0.263
1.601
2.303
Wing
0.251
2.300
3.440
2.900
4.170
1.999
0.250
2.300
Rotated 90 degrees
4.170
2.400 2.300 2.400
2.90
0.375
0.920
2.300 2.300 2.301
Wing 2.401 2.303 2.400
Axle
0.500
Axle
3.406
0.250
0.263 2.303
Axle
2.3 2.3 2.3
3.350
2.300
Wing
0.273
1.060
0.506 2.403
1.059
0.375
Axle
1.960
0.864
Wing
Wing .25"
2.3 2.3 2.3
Wing
2.300
2.400
2.301
2.403
0.921
Fuse