Académique Documents
Professionnel Documents
Culture Documents
Safety Summary
WARNING In case of power cord damage, do not attempt to repair or replace the power cord. Contact the manufacturer or the local distributor. WARNING Hot Surface. Avoid contact. CAUTION During normal operation, the base of the machine needs to be installed or placed above the wall socket. CAUTION The machine is to be operated by one person only. CAUTION To reduce the risk of electric shock and injury to persons, disconnect from power supply before servicing and /or cleaning.
International Symbols
O I
Power Off
Power On
Hot Surface
Ground
Caution - Warning
-1-
Installation
DOMESTIC Use a separate 15 amp AC circuit. Only industrial extension cords with proper wire size should be used: size 16/3 wire for distances up to 25 feet, and size 14/3 for distances up to 50 feet. INTERNATIONAL Use a designated 16 amp AC circuit. Only industrial extension cords with proper wire size (2.5 sq. mm) shall be used. IMPORTANT The appliance must be plugged into a proper receptacle of the proper size and rating. Equally important the line voltage must be able to accommodate this appliance as well as other appliances operating on this circuit.
Operation
1. 2. Turn the power on by pressing the POWER button on the controller. Set desired temperature and time. Swing the upper platen arm to its fully open position, away from lower platen. (See Solid State Controller section) Allow the machine to warm up until the selected temperature is reached. Set the desired pressure by adjusting the crank handle knob on the top of the machine. To increase pressure, turn the crank handle knob counter-clockwise. Place the substrate on lower platen, smoothing out all wrinkles. Position transfer or lettering on substrate. Swing the upper arm into position directly over the lower platen.
3. 4.
Specifications
Voltage Model 204 Voltage Model 204 120 Volts AC 1750 Watts 230 Volts AC 2200 Watts 50/60 Hertz 14.6 Amps 50/60 Hertz 9.6 Amps
5. 6. 7.
-2-
Controller Operation
1. If the temperature is not being displayed, press the MODE button until temperature is displayed. 2. Push and hold SET button and simultaneously push UP () or DOWN () arrow buttons to the desired temperature setting. 3. Press the MODE button until time is displayed. 4. Push and hold SET button and simultaneously push UP () or DOWN () arrow buttons to the desired timer setting.
10. Lift safety lock and pull handle up slowly and move upper platen handle to its full open position. This technique will avoid transfer paper (cover) from being pulled off prematurely due to suction from the separating platens. NOTE For safety purposes, it is necessary to push the handle into the locked position after it is lifted. This will eliminate the accidental lowering of the heat platen handle. 11. Swing away arm to the extreme right hand position and remove substrate.
Timer
The controller has a count down timer that automatically activates a buzzer at the completion of the application. Timer display is minutes:seconds. Range is 00:00 to 99.59, Colons (:) flash while timer is running. NOTE The timer or buzzer may be stopped while the handle is in the down position by pressing the MODE button. The timer will automatically reset after the handle is raised.
Counter
The controller has a built in cycle counter. Press MODE button until the counter is displayed. Counter display range is 0000 to 9999. To reset the cycle counter, display the counter reading, then push and hold both UP () and DOWN () arrow buttons for 3 seconds until the counter resets to zero (0000) on the display.
-3-
General Maintenance
It is recommended that you have the following items available: A. Regular screw driver B. Phillips head screw driver C. Small adjustable wrench D. Needle nose pliers with insulated handle E. Set of Allen wrenches F. Grease gun G. Special high temperature grease MPPL023 With the above items you should be able to accomplish most repairs. WARNING Power cord replacement should be from the manufacturer only (because it requires a specially prepared cord).
2.
3. 4.
5.
Use tube of MPPC006 adhesive to bond silicone rubber pad to metal platen. NOTE: Read instructions on the tube package. 3. 4. 5. Be sure that the surface of the silicone platen is clean. Use a mild solvent such as mineral spirits. The pad and metal must be thoroughly dry and clean, before starting the bonding operation.
In addition, occasionally apply a few drops of heavy machine oil to the upper portion of the cam assembly.
Apply adhesive sealant to the metal platen. Spread a thin even coat and apply pad immediately. Apply pressure and position pad making sure that there is no air entrapment. NOTE: A serrated blade such as used for laying down rubber floor tiles would be helpful. 6. Allow to cure overnight under low pressure at normal room temperature.
-4-
-5-
NO 1 2 3 4 5 6 7 8 9 11 13 14 15 16 17 18 19 20 21 22 23 25 26 27 29 30 32 33 34 35 36 37 38 39 40 41 42 43 45 47 48 49 50 52 53 54 55 57 58 59 60 63 68 69 70 71
DESCRIPTION SHROUD, HEAT SCREW, BUTTON HD 5/16-18 X .50" LG INSULATION, FIBERGLASS 15X20 SCREW, SOCKET HD 1/4-20 X 4 LG TUBING, SHRINK TFE AWG7 INSULATORS, SPACER (4/SET) PLUG, BUTTON 7/8 IN SENSOR, TEMP. REPLACEMENT KIT POST, GUIDE LUG PIN CLEVIS, UPPER PLATEN PAD, SILICONE 15 X 20 BLK SCREW, PAN 10-24 X .50 LG HOUSING, INSTRUMENT WIRE, HEATER 14GA TGGT LABEL, CONTROLLER OVERLAY BOLT, HEX 5/16-18 X 1 LG STAINLESS SCREW, BUT HD 1/4-20 X .75" LG HANDLE, PRESSURE ADJUST F/204 SCREW, PAN HD 6-32 x 0.25 IN CONTROLLER, DIGITAL W/SWITCH HANDLE, SWINGAWAY 200 WASHER, SAE 1/4" SWITCH, MICRO NUT, HEX 3/8-16 LOCKING PLUNGER SPRING DETENT 500 SCREW, SOCKET HD 1/4-20 X .50 HD KNOB, HANDLE (MUSHROOM) CAP, VINYL BLK 5/16X.281 LG RELAY SCREW, BTN HD 1/4-20 X .875LG BLOCK, TERMINAL CLAMP, CABLE 5/16 IN. TRANSFORMER SCREW, RD HD 4-40X.625" LG SCREW, PRESSURE ADJUSTMENT POST, ARM ASSY PLATE, POST STOP WASHER, SAE 1/2" NUT, JAM SELF LOCKING 1/2-20 CLIPS, "E" PIN, CAM PIVOT (UPPER) SCREW, PAN HD 8-32 X .375" LG SAFETY LOCK WASHER, #8 SAE FITTING, GREASE (SHORT) PIN, ROLL (SAFETY LOCK) CAM SCREW, BUTTON HD 5/16-18 X1 LG NUT, HEX JAM 5/16-18 RING, "O" POST FEET,RUBBER (6/SET) BRACKET, POWER CORD STRAIN RELIEF 14/3 SCREW, PAN HD 10-24 X .375 LG CORD, POWER (USA)
MODEL 204 120V AC MPS90174 MPSB5161812 MPSP254 MHSSH14204 MPPS131 MPI90156 MHPB78 MPPS210 MPSP084 MPP90141 MPSP221 MPPP031 MHSP102412 MPSH015 MPPW700 MPSL128 MPBH14201S MHSB142034 MPSP014 MHSP63214 MPC90003 MPH90002 MHWSAE14 MPPS043 MHNH3816 MPSP134 MHSSH142012 MPPK017 MPC90006 MPPR200 MHSB142078 MPB90006 MHCC516 MPT90001 MHSR44058 MPSS070 MPSP204 MPSP20450 MHWSAE12 MHNHJSL1220 MPSC240 MPSP262 MHSP83238 MPSL241 MHWSAE8 MPSF145 MPSR141 MPSC220 MHSB516181 MHNHJ51618 MPSS273 MPF90004 MPSS163 MPSS168 MHSP102438 MPPW141
MODEL 204 230V AC MPS90174 MPSB5161812 MPSP254 MHSSH14204 MPPS131 MPI90156 MHPB78 MPPS210 MPSP084 MPP90141 MPSP221 MPPP031 MHSP102412 MPSH015 MPPW700 MPSL128 MPBH14201S MHSB142034 MPSP014 MHSP63214 MPC90003 MPH90002 MHWSAE14 MPPS043 MHNH3816 MPSP134 MHSSH142012 MPPK017 MPC90006 MPPR200 MHSB142078 MPB90006 MHCC516 MPT90001 MHSR44058 MPSS070 MPSP204 MPSP20450 MHWSAE12 MHNHJSL1220 MPSC240 MPSP262 MHSP83238 MPSL241 MHWSAE8 MPSF145 MPSR141 MPSC220 MHSB516181 MHNHJ51618 MPSS273 MPF90004 MPSS163 MPSS168 MHSP102438 MPPW142
71A 71B 72 76 78 79 80 82 84 87 88 89 90 91 92 93 94 95 96 97 A1 A2 A3 A4 A5 A6
CORD, POWER (EUROPEAN) 230V CORD, POWER (U.K) 240V WIRE, HARNESS SPRING, CAM INSULATION, MICRO SWITCH WASHER, CUT 5/16" SCREW, SKT HD 5/16-18 X .50 LG CLAMP, CABLE 3/8" (STEEL) SCREW, PAN HD 8-32 X 1/4 LG SCREW, PAN HD 8-32 X 1/2 LG SCREW, SOCKET HD 1/4-20 0.5 LG NUT, HEX 6-32 NUT, JAM 1/2-20 SCREW, SET 3/8-16 X .500 LG BUSHING, GUIDE POST WASHER, SHIM #6 (.031) SPACER, NYLON 0.166 ID X1/4 LG PLATE, CONTROLLER WIRE, GROUND ASS'Y LABEL, ROHS/WEE PLATEN, HEAT ASS'Y HANDLE, PRESSURE ASS'Y CAM ASS'Y BASE ASSEMBLY PLATEN, LOWER ASSY PLATEN, HEAT W/WIRNG
N/A N/A MPW90011 MPSS201 MH700214 MHWC516 MHSSH5161812 MH8863T2 MHSP83214 MHSP83212 MHSSH142012 MHNH632 MHNHJ1220 MHSST516184 MPSB074 MH311150019 MH110969111 MPP90011 MPW90125 MPL90175 MPP2041A MPSH515 MPSC213 MPSB204A MASP007 MPP2041W
MPPW202 MPPW203 MPW90011 MPSS201 MH700214 MHWC516 MHSSH5161812 MH8863T2 MHSP83214 MHSP83212 MHSSH142012 MHNH632 MHNHJ1220 MHSST516184 MPSB074 MH311150019 MH110969111 MPP90011 MPW90125 MPL90175 MPP2042A MPSH515 MPSC213 MPSB204A MASP007 MPP2042W
- 10 -