Académique Documents
Professionnel Documents
Culture Documents
com
Data Sheet
1.6000
reduction. Low loss. Ideal for operating at X-band or below. Low Z-axis expansion for RT/duroid 6010LM. Provides reliable plated through holes in multilayer boards. Low moisture absorption for RT/duroid 6010LM. Reduces effects of moisture on electrical loss. Tight r and thickness control for repeatable circuit performance.
Some Typical Applications: Space Saving Circuitry Patch Antennas Satellite Communications Systems Power Ampliers Aircraft Collision Avoidance Systems Ground Radar Warning Systems
The information in this data sheet is intended to assist you in designing with Rogers circuit material laminates. It is not intended to and does not create any warranties express or implied, including any warranty of merchantability or tness for a particular purpose or that the results shown on this data sheet will be achieved by a user for a particular purpose. The user should determine the suitability of Rogers circuit material laminates for each application.
Typical Values
PROPERTY
Dielectric Constant, r Dissipation Factor, tan Thermal Coefcient of r Surface Resistivity Volume Resistivity Youngs Modulus under tension ultimate stress ultimate strain Youngs Modulus under compression ultimate stress ultimate strain Flexural Modulus ultimate stress Deformation under load Moisture Absorption Density Thermal Conductivity Thermal Expansion Td Specic Heat Copper Peel Flammability Rating Lead-Free Process Compatible
DIRECTION
Z
UNITS[1]
CONDITION
10 GHz/A
TEST METHOD
IPC-TM-650 2.5.5.5
0.0027 -410 7x107 2X107 627 (91) 517 (75) 20 (2.8) 17 (2.5) 12 to 13 4 to 6 1069 (155) 54 (7.9) 33 2634 (382) 1951 (283) 38 (5.5) 0.33 2.10 0.05 2.7 0.48 (3.3) 47 34, 117 500 0.97 (0.231) 14.3 (2.5) 94V-0 Yes
Z Z Mohm Mohm cm MPa (kpsi) MPa (kpsi) % MPa (kpsi) MPa (kpsi) % MPa (kpsi) MPa (kpsi) % % % W/m/K (BTU/in/ft2/hr/F) ppm/C C TGA J/g/K (BTU/lb/F) pli (N/mm)
X Y X Y X Y Z Z Z X Y X Y Z Z
ASTM D790 ASTM D621 IPC-TM- 650 2.6.2.1 ASTM D792 ASTM D2214, Modied ASTM 3386 (5K/min) ASTM D3850 Calculated IPC-TM-650 2.4.8 UL
[1] SI unit given rst with other frequently used units in parentheses. [2] References: APR4022.33 DJS 4019.27-32, Internal TR 2610. Tests were at 23C unless otherwise noted. Typical values should not be used for specication limits. [3] Dielectric constant is based on .025 dielectric thickness, one ounce electrideposited copper on two sides. Typical values are a representation of an average value for the population of the property. For specication values contact Rogers Corporation.
STANDARD THICKNESS:
0.010 (0.254mm) 0.025 (0.64mm) 0.050 (1.27mm) 0.075 (1.90mm) 0.100 (2.50mm) USA: Belgium: Japan: Taiwan: Korea: Singapore: China:
oz. (8 m) electrodeposited copper foil. oz. (17m), 1 oz. (35m), 2 oz. (70m) electrodeposited and rolled copper foil. Heavy metal claddings are available. Contact Rogers Customer Service. Tel: 480-961-1382 Tel: 32-9-2353611 Tel: 81-3-5200-2700 Tel: 886-2-86609056 Tel: 82-31-716-6112 Tel: 65-747-3521 Tel: 86-21-63916088 Fax: 480-961-4533 Fax: 32-9-2353658 Fax: 81-3-5200-0571 Fax: 886-2-86609057 Fax: 82-31-716-6208 Fax: 65-747-7425 Fax: 86-21-63915060
CONTACT INFORMATION:
Rogers Advanced Circuit Materials Rogers NV - Gent Rogers Japan Inc. Rogers Taiwan Inc. Rogers Korea Inc. Rogers Technologies Singapore Inc. Rogers (Shanghai) International Trading Co., Ltd
The information in this data sheet is intended to assist you in designing with Rogers circuit material laminates. It is not intended to and does not create any warranties express or implied, including any warranty of merchantability or tness for a particular purpose or that the results shown on this data sheet will be achieved by a user for a particular purpose. The user should determine the suitability of Rogers circuit material laminates for each application. These commodities, technology and software are exported from the United States in accordance with the Export Administration regulations. Diversion contrary to U.S. law prohibited. RT/duroid, The world runs better with Rogers. and the Rogers logo are licensed trademarks for Rogers Corporation. 1991, 1992, 1994, 1995, 1998, 2002, 2005, 2006, 2007 Rogers Corporation, Printed in U.S.A. All rights reserved. Revised 05/2007 0697-0507-.5CC Publication: #92-105