Académique Documents
Professionnel Documents
Culture Documents
xls
TISSOT S.A
INFORMACION GENERAL
ASME SECTION VIII Div.1 Ed.1998 add.1999
RECIPIENTE
DIAMETRO INTERIOR LONGITUD CILINDRICA TIPO DE CABEZAS TOLERANCIA CORROSION CAPACIDAD GEOMETRICA AREA SUPERFICIAL PESO ESTIMADO
2,133 mm 9,214 mm
22,262 Lb
Kg Kg Kg
176134228.xls.ms_office
TISSOT S.A
Design Information Pd = Pressure Design Inside Diameter (new) Dn = Inside Diam.(corroded) I D = H= Hydrost.Head Shell Material Allow.Stress @ Des.Tem. S= 180 Psi. 83.98 inch 84.23 inch 3.0 Psi. SA-515 Gr 70 17,500 Psi Design Temperature Corrosion Allowance Joint Efficiency
Total Internal Press. P = Pd +H =
T= C= E=
P=
Sa =
Psi UG-27
t=
PR
+C
0.383 inch
9.740
mm
t=
PR
+C
0.647 inch
16.436
mm
ts :
0.599 inch
MAWP =
-H
163.3 Psi
MAWPnc =
-H
207.36 Psi
Hydrostatic Test Pressure Calculations 1.3 * MAWP * Sa = 212.2 Psi HPmax = 1.3 * MAWPnc = 269.6 Psi
HPmin=
Cold Formed Heat Treatment Requirements for Carbon Steels per UCS-79
Final center line radius Rf = 42.3 inch Original center line radius Ro = =
1.00E+100
inch
% = 50 * ts * (1-Rf/Ro) / Rf
0.71 %
If % is >5% and any of the following conditions exists: 1) Lethal Service, 2) Charpy is required, 3) ta>5/8", '4) Thickness Reduction by forming >10%, and forming temperature is between 250F. and 900F. Heat Treatment by Cold Forming is required.
F. F. F.
F. F.
If the lower of above MDMT's is > to Design MDMT Is the Charpy Test required ?
Pgina 3
176134228.xls.ms_office
TISSOT S.A
Serial Number : Drawing No. :
Design Information Design Press. Pd = 180.0 Inside Radius L= 42.11 Corr.Allowan. C= 0.1250 Hydrost.Head H= 3.0 Head Material SA-285 Gr C Allow. Stress @ Des. TS = 13,800 Psi. inch inch Psi Psi Design Temperature Outside Radius Head Effiency
Total Design Press P= P+H
T= Ro = E=
P=
Sa =
Psi
t=
P (L+C)
+C
0.455 inch
11.557
mm
to :
0.500 inch
USAR CABEZA CON ESTE ESPESOR MINIMO
12.700
mm
MAWP =
2* S * E * (to-C)
-H
204.9 Psi
MAWPnc =
2 * Sa * E * to
-H
274.9
Hydrostatic Test Pressure Calculations HPmin= 1.3 * MAWP * Sa = 266.4 Psi HPmax = 1.3 * MAWPnc = 357.3
Cold Formed Heat Treatment Requirements for Carbon Steels per UCS-79
Final center line radius Rf = 42.4 inch Original center line radius Ro = 1.00E+100 =
% = 75 * to * (1-Rf/Ro) / Rf
0.89 %
If % is >5% and any of the following conditions exists: 1) Lethal Service, 2) Charpy is required, 3) ta>5/8", 4) Thickness Reduction by forming >10%, and forming temperature is between 250F. and 900F. Heat Treatment by Cold Forming is required.
Page 4of 4
176134228.xls.ms_office
UG-32
UG-32 Psi
Psi
inch
F. F.
Page 5of 5
Especificacin Numero - Grado SA-105 SA-106 Gr B SA-181 Gr 1 SA-193 Gr B72" SA-194 Gr 2H SA-283 Gr C SA-285 Gr C SA-307 B SA-350 Gr LF1 SA-350 Gr LF2 SA-515 Gr 55 SA-515 Gr 60 SA-515 Gr 65 SA-515 Gr 70 SA-516 Gr 55 SA-516 Gr 60 SA-516 Gr 65 SA-516 Gr 70 SA-53 Gr B
PROPIEDADES DE LOS MATERIALES ACERO AL CARBON Y BAJO CONTENIDO DE DE EL Valores mximos de esfuerzos permitido a tensin 1000 psi Para temperatura del metal no mayor de, - 20 a 650 700 750 800 850 900 17.5 16.6 14.8 13.0 9.3 6.5 15.0 14.4 13.0 10.8 8.7 6.5 15.0 14.4 13.0 10.8 8.7 6.5 25.0 25.0 23.6 21.0 17.0 12.5 12.7 13.8 13.3 12.1 10.2 8.4 6.5 15.0 14.4 13.0 10.8 7.8 5.0 17.5 16.6 14.8 12.0 7.8 5.0 13.8 13.3 12.1 10.2 8.4 6.5 15.0 14.4 13.0 10.8 8.7 6.5 16.3 15.5 13.9 11.4 9.0 6.5 17.5 16.6 14.8 12.0 9.3 6.5 13.8 13.3 12.1 10.2 8.4 6.5 15.0 14.4 13.0 10.8 8.7 6.5 16.3 15.5 13.9 11.4 9.0 6.5 17.5 16.6 14.8 12.0 9.3 6.5 15.0 14.4 13.0 10.8 8.7 6.5
JO CONTENIDO DE DE ELEMENTOS DE ALEACION tido a tensin 1000 psi a del metal no mayor de, F 950 1050 1100 4.5 2.5 4.5 2.5 4.5 2.5 8.5 4.5 3.0 1.5 3.0 1.5 4.5 2.5 4.5 2.5 4.5 2.5 4.5 2.5 4.5 2.5 4.5 2.5 4.5 2.5 4.5 2.5 -
1150 -
1200 -