Académique Documents
Professionnel Documents
Culture Documents
FIST
Fiber Infrastructure System Technology
This document provides assistance with the selection of racks for use in FIST applications. It includes the following sections:
1. PRODUCT DESCRIPTION 2. ORDERING INFORMATION
2.1 2.2 2.3 3.1 3.2 3.3 Generic Rack Alternatives Accessories Tools Rack Description Rack Dimensions and Capacity Accessories Description
3. PRODUCT GUIDE
Please consult your local sales engineer for applications not included in this document.
Page 1 of 15
side duct
pigtail storage drum pigtail containment bracket horizontal pigtail management (HPM)
Page 2 of 15
Covers (Ref. 3.1.5) No covers Covers for all sides, HPM and base duct system, no front door D Covers as option S, front door without lock L Covers as option S, front door with lock T Line-up configuration for option S E Line-up configuration for option D M Line-up configuration for option L N S
Side Duct Contents (Ref. 3.1.7) N 1 2 3 None 100% with drums and brackets The right-hand duct is fitted with drums and brackets 100% at front, dummy back
Cable and Pigtail Management (Ref. 3.1.8) N H D B None HPM only Base duct only Both HPM and base duct
Page 3 of 15
2.2 ACCESSORIES
Accessories are ordered in addition to the basic rack to suit specific applications. Refer to Section 3.3. for a complete product description and pictures.
(*) Add -I for installation in a 19 rack. Issue 2.6 (01-01) Page 4 of 15 Product Manager: E.Visser
2.3 TOOLS
Name FACC-ALLEN-KEY-5-350 FACC-CAGE-NUT-TOOL
Key: pc = piece pk - pack
Qty/Pk 1 pc 1 pc
Description Allen key, diameter 5 mm, length 350 mm for back-mounting of shelves in rack For installation of cage nuts in the rack
qty = quantity
RACA043.JPG
Base Duct System This is an optional system to control cable element and pigtail routing at the base of the rack. Rack occupancy: 325 mm (13 ETSI HU). It includes a cable element management tray and a pigtail duct: Cable Element Management Tray The base frame includes a cable element management tray that facilitates the routing of cable elements from the cables to the shelves.
RACA047.JPG
Page 5 of 15
FIST-GR Ordering Guide Pigtail Duct The bottom of the base frame contains a pigtail and patch cord duct system that is used to carry pigtails and patch cords from one side duct to the other, or from one rack to another in a back-to-back configuration.
RAIG031.JPG
RAIG027.JPG
Pigtail Containment Bracket Optionally, pigtail containment brackets can be fitted at regular intervals on the plate so that cables and pigtails can be secured neatly and separated from the flex tubes.
pigtail containment bracket
RAIG028.JPG
Pigtail Storage Drums Optionally, pigtail storage drums can be fitted on the side ducts. These allow pigtail/patchcord overlength storage for inter-rack patching (bottom section of side duct) and overlength storage for outgoing pigtails (top section).
RAIG029.JPG
Page 6 of 15
b) Rack Type: XY X = 3 300 mm deep frame with or without side ducts depending on the choice of option Y. Shelf units mount from the front only.
X = 6 600 mm deep frame with or without side ducts. Shelf units are mountable on both sides, except for side ducts option 3 (Ref 3.1.7) where shelf units are front-mounted and there is a dummy back.
OR
Page 7 of 15
Bottom with adjustable feet. Note: This option cannot be used with rack layout 36 or 66.
RAIG032.JPG
3.1.5 Covers
Order Ref. N S Description None, no covers supplied with the rack. Covers included for all sides, horizontal pigtail management system (HPM) and base duct system. No front door. Covers included for all sides as for option S. D A front door without a locking mechanism is also supplied. The door covers the front of the shelf mounting bay. Covers included for all sides as for option S. L A front door with a locking mechanism is also supplied. The door covers the front of the shelf mounting bay. T As for option S but for in-line installed racks E As for option D but for in-line installed racks. M As for option L but for in-line installed racks. Note: Options D and L cannot be used with rack layouts 36 and 37, nor 66 and 67. Use covers only - option S - or no covers at all - option N.
RAIG023.JPG
3.1.6 Mounting
Order Ref. Description Vertical mounting profiles with ETSI pitch. G Distance between profiles according to ETSI. Vertical mounting profiles with ETSI pitch. I Distance between profiles according to 19.
Page 8 of 15
The base duct system, including the cable element management tray and the pigtail duct is provided.
RAIG033.JPG
B N
Both options H and D are provided. No HPM and no base duct system are supplied.
RA14.JPG
Page 9 of 15
80 16
60 12
For typical arrangements with FIST elements and shelves refer to the FIST-GR installation instructions. With reference to the table above, the capacity of the other FIST-GR racks are as follows: Rack FIST-GR-X69 Capacity Twice FIST-GR-X39
FIST-GR-X67 Twice FIST-GR-X37 (except if side ducts option 3 is selected, then the rack capacity is the same)
Page 10 of 15
Flexible Tube Clamps FISTV-FTC A set of 10 plastic clamps to be used instead of tie-wraps to secure flexible tubes onto the cable element management tray or other locations.
FTC.JPG
Tie Wraps FISTV-TW-NN-188 188 mm long tie wraps are used for fixing the cable and flexible tubing to the rack.
I&C025.JPG
Cable Shield Grounding Kit FIST-GR-CSGK Consists of a plate with 6 grounding points for cable shields. The plate can be installed in the top or bottom cable entrance locations. The grounding wire and the connection with the cable shield depend on the cable construction and are not included in the kit. Extra Cable Termination Kit FIST-GR-ECTK This plate can be added in a rack to extend the capacity with 4 or 6 additional cable terminations depending upon which cable attachment rail is selected (see below).
GR-CSGK.JGP
GR-ECTK.JPG
Page 11 of 15
FIST-GR Ordering Guide Cable Attachment Rail FIST-GR-CAR-128-1622 This consists of a rail and cable clamps to be mounted on a cable termination plate: FIST-GR-ECTK. It allows 4 cables (16-22 mm) to be attached via individual cable clamps instead of tie-wraps. To clamp 6 cables (12-16 mm), use FIST-GR-CAR-128-1216.
GR-CAR.JPG
Multiple Cable Termination Kit FIST-GR-MCTK This consists of a split level plate to be mounted on the cable element management tray. It allows cables to be attached via individual cable clamps on both levels. Depending upon which cable attachment rail is used (see below), either 2 x 8 or 2 x 10 cables can be secured.
GR-MCTK.JPG
Cable Attachment Rail FIST-GR-CAR-215-1622 This kit allows 7 additional cables (16-22 mm) to be attached via individual cable clamps on any level of the multiple cable termination kit. To clamp10 cables (12-16 mm) use the FIST-GR-CAR-215-1216.
GR-CAR.JPG
Cable Termination Eyelet FISTV-E7531-0169 Bags of 50 crimpable eyelets to terminate cable strength members (2.5-4 mm). These eyelets can then be attached with a screw to the cable termination plate.
IC&CC100.JPG
Page 12 of 15
Pigtail Orientation Module FIST-GR-POM A 5 ETSI HU high module with cover to be inserted in a rack allowing to redirect or branch a pigtail bundle. It also exists in 19 width (FIST-GR-POM-I).
RAIG039.JPG
Horizontal Pigtail Management FIST-GR-HPM A horizontal pigtail management system (HPM) with cover can be fitted to store overlengths of patchcords for patching within the same rack. The system can be fitted in the rack for either left or right patchcord entrance by simply turning it upside down. It also exists in 19 width (FIST-GR-HPM-I).
RACA043.JPG
Grounding Kit FIST-GR-GK Provides all the components to connect all rack covers together for grounding purposes. Connections are made with 2.5 mm2, yellow/green color coded wires. Grounding of the shelves to the rack is provided via the shelf mounting brackets. Each kit contains components for up to one 300 x 900 x 2200 mm rack.
RA07.JPG
Page 13 of 15
FIST-GR Ordering Guide Mounting Bracket for 19 equipment shelf FIST-GR-19I-2HU (3HU, 4HU) This can be used to mount 19 equipment shelves in an ETSI rack FIST-GR (also exists for a 19 FIST-GR). The brackets exist in different heights (2HU, 3HU and 4HU) to allow for different sizes of equipment shelves. The depth positioning of the shelves in the rack can be varied. Each kit contains 1 pair of brackets and fixing components. Notes: Cable access should be through the front or the back of the equipment shelf. The rack does not provide controlled heat management. Back-to-Back Connection Kit FIST-GR-BTBC This provides the accessories to mount a 300 mm deep rack back-to-back with another 300 mm deep rack. Each kit contains the accessories for mounting racks up to 900 mm wide.
RA04.JPG
RA10.JPG
Side-to-Side Connection Kit FIST-GR-STSC Provides the accessories to mount a 300 mm deep rack side-to-side with another 300 mm deep rack.
RAOG2001.JPG
Bags of Drums FIST-GR-DRM Kit of 10 drums with the typical hardware to fix them to the back of an empty duct.
RACA045.JPG
Page 14 of 15
FIST-GR Ordering Guide Dummy Shelf Cover FIST-GR-DSC This kit includes a shelf front cover and the hardware to fix it inside any FIST-GR rack. It allows a rack to be completely loaded by filling any empty 5 ETSI HU high position. It exists also in 19 width.
RACA057.JPG
Velcro Roll FISTV-E7187-6316 Velcro to segment or secure pigtails. Supplied on a roll 25 m long (width 25 mm) to be cut to length as required.
FRWR044.JPG
Page 15 of 15