Académique Documents
Professionnel Documents
Culture Documents
Single Double
Y Y
Y Y
Light to Medium
N N N N Y Y Y
Y Y Y Y N N N
Aggregate
Medium to Heavy
Osborn Linear Horizontal and up to 5 Decline Osborn Exciter Driven Horizontal, Inclined and Multislope Multislope - 2 to 5 slopes
Medium to Heavy
Y Y
Y Y
Osborn Mogensen
3-5 Deck
Accurate Sizing
Light duty
Out of Balance Motors Linear Motion Exciter Driven (Gearbox) Linear Motion
Single
G forces are very important in screen selection 5 Gs is considered the norm in South Africa. The bigger the screen aperture the higher the machine stroke. Thus the speed will decrease. On fine apertures high speed with a small stroke is required. G force is calculated as stroke multiplied by speed.
The Osborn OBEX screen was developed as a replacement for the older shaft driven series. The main features are lower power consumption, low operating noise and easy maintenance. OBEX screens can be used for conventional screening, dewatering and washing applications. Osborns OBEX screens are supplied with polyurethane screen panel decks as a standard, but can be fitted with woven wire decks if required. Two vibrating out of balance motors rotate in opposite directions, synchronising and imparting a vibrating force in a longitudinal direction. This lifts the material and carries it forward on each rotation providing a partical travel rate. The amplitude can be varied by adjusting the out of balance weights on the vibrating motors to the required stroke. The frequency depends on the use of either 4 pole or 6 pole motors as dictated by the application. When dewatering on a 5 upslope, the use of a variable speed drive VSD is recommended to achieve optimal speed and performance.
Width x Length
TRIPLE DECK
4 x 10 (1220 mm x 3050 mm) 5 x 10 (1525 mm x 3050 mm) 5 x 12 (1525 mm x 3660 mm) 5 x 14 (1525 mm x 4270 mm) 5 x 16 (1525 mm x 4880 mm) 6 x 16 (1830 mm x 4880 mm) 6 x 20 (1830 mm x 6100 mm) 7 x 20 (2135 mm x 6100 mm) 7 x 20 (2135 mm x 6100 mm) Dual Drive 8 x 20 (2440mm x 6100 mm) Dual Drive 8 x 22 (2440mm x 6710 mm) Dual Drive
DOUBLE DECK
5 x 10 (1525 mm x 3050 mm) 5 x 12 (1525 mm x 3660 mm) 5 x 14 (1525 mm x 4270 mm) 5 x 16 (1525 mm x 4880 mm) 6 x 16 (1830 mm x 4880 mm) 6 x 20 (1830 mm x 6100 mm) 7 x 20 (2135 mm x 6100 mm) 7 x 20 (2135 mm x 6100 mm) Dual Drive 7 x 20 (2135 mm x 6100 mm) Heavy Duty 8 x 20 (2440 mm x 6100 mm) 8 x 20 (2440 mm x 6100 mm) Dual Drive 8 x 24 (2440 mm x 7320 mm) Dual Drive 8 x 29 (2440 mm x 8845 mm) Dual Drive
FOUR DECK
6 x 16 (1830 mm x 4880 mm)
The Osborn SUPERKING screens are frequently used in primary screening and scalping operations and have proved to be exceptionally reliable in the mining and quarrying industries. Generally operating at 16 to 20 installation angle, the SUPERKING produces a maximum of 12 mm stroke at around 5Gs. The SUPERKING has fully adjustable counterweights for optimum screening and efficiency. Available in single, double, triple or 4 deck configurations, these screens are equally efficient for screening dry or wet gravel, sand, crushed stone and all types of ore. The drive is a self contained vibrator unit complete with a heavy duty steel shaft and fitted with grease lubricated self aligning spherical roller bearings. The unit is completely enclosed and dust tight. To ensure that the feed material spreads across the full width of the screen deck, the SUPERKING screens are fitted with screen feed boxes as standard. The Osborn SUPERKING screens are supplied with woven wire screen decks as a standard but can be fitted with polyurethane screen panels if required.
NOTES For sizes not listed here please consult Osborn. Where dual (2 drives) are shown it indicates a twin drive mechanism timed by a toothed belt for heavy duty applications.
high volume screen, superior in screening efficiency and capacity versus the more conventional horizontal and declined models. It is available in single deck & double deck configuration. The unbalanced Exciter Drive, designed and manufactured in SA, consists of a sturdy soundproof housing which contains two shafts that are synchronised with gears and mounted in heavy duty roller bearings. Lubrication of the bearings and gears is achieved by a combination of an oil bath and an oil mist. Eccentric weights are attached to both ends of the shaft. While stationary, the unbalanced mass can be changed by adding or removing weights. This alters the strength of the unbalanced exciter drive force and the oscillation amplitude of the vibratory equipment. The Multi Slope Type Screen with the Exciter Drive is made up of two, three or five decks that are installed at different angles. The Exciter Drive gearbox is mounted over the top of the screen which imparts a straight linear motion through the screen arrangement. Used extensively in the coal and diamond processing industry, the Osborn Multi Slope Type Screen has the capability of handling wet and sticky materials. This is due to the aperature sizes changing over the full screen length by virtue of the different deck angles and particle approach angles.
Width x Length
8 x 18 (2440 mm x 5490 mm) 10 x 18 (3050 mm x 5490 mm) 10 x 20 (3050 mm x 6100 mm) 10 x 22 (3050 mm x 6710 mm) 12 x 24 (3660 mm x 7320 mm) 12 x 26 (3660 mm x 7930 mm) 12 x 30 (3660 mm x 9150 mm) These screens can be installed up to an angle of 20
Width x Length
8 x 18 (2440 mm x 5490 mm) 10 x 18 (3050 mm x 5490 mm) 10 x 22 (3050 mm x 6710 mm) 12 x 24 (3660 mm x 7320 mm) 12 x 26 (3660 mm x 7930 mm) 12 x 30 (3660 mm x 9150 mm) Osborn Exciter Driven Multi Slope screens can be built with deck configurations in 2, 3 and 5 slopes.
Width x Length
SINGLE DECK
Width x Length
TRIPLE DECK
Operating with a three way motion (horizontal, vertical and elliptical), this unique movement quickly stratifies and turns materials so that all sides of each particle are exposed to deck openings and where fitted, water spray nozzles. The result is more complete screening, accurate sizing and more thorough dewatering. The heart of the Osborn Linear Screen is the Vibrator mechanism. Twin shafts, driven through wide face helical gears, are completely enclosed in a dust proof housing which contains a large oil reservoir to provide splash lubrication to the gears and bearings. The oil assists in dissipating heat and lowers bearing temperatures for longer bearing service life. The single shaft extension vibrator can be turned end for end (and gears retimed) to change the hand orientation of the drive, because the short vibrator side plates are symmetrical. Therefore, one vibrator for left hand and right hand drive.
5 x 14 (1525 mm x 4270 mm) 5 x 16 (1525 mm x 4880 mm) 6 x 16 (1830 mm x 4880 mm) 7 x 20 (2135 mm x 6100 mm) 8 x 20 (2440 mm x 6100 mm) 8 x 24 (2440 mm x 7320 mm)
DOUBLE DECK
5 x 10 (1525 mm x 3050 mm) 5 x 12 (1525 mm x 3660 mm) 5 x 14 (1525 mm x 4270 mm) 6 x 16 (1525 mm x 4880 mm) 7 x 20 (2135 mm x 6100 mm) 8 x 20 (2440 mm x 6100 mm) 8 x 24 (2440 mm x 7320 mm)
WIDE-FACE HELICAL GEARS Timing gears are premium-quality, single helical design, precision-cut from 4140 heat-treated steel. Wide-faced gear teeth distribute load much more effectively than spur gears, and promote smooth, quiet, long-lived operation under heavy loading. VIBRATING SHAFTS Each tough, eccentric, vibrator shaft is precision-machined from 1045 steel for extra-long service.
OIL FLINGER
DOUBLE-LIP SEAL Retains oil and prevents contaminants from entering vibrator mechanism. Seals and seal sleeve are easily replaceable when worn.
OIL-SPLASH LUBRICATION Through-flow, oil splash system provides superior lubrication of gears and bearings. Large oil reservoir, extending the entire length of vibrator housing, dissipates heat rapidly, and lowers bearing temperatures for longer bearing service life.
TRANSVERSE FEEDER
The transverse feeder is available in four sizes being suitable for feeding the 1.0, 1.5, 2.0 and 3 meter wide sizers and screens. They are suitable for accepting a feed and turning through 90 degrees into a steady and continuous flow across the width of the screen feed plate. Occasionally they can be supplied to feed two machines mounted in parallel.
CENTRAL FEEDER
The central feeder again is available in four sizes suitable for feeding the 1.0, 1.5, 2.0 and 3 meter wide sizers and screens. They accept a central feed and spread the material sideways in two directions across the width of the screen feed plate.
Application Data
Customer Tel No. Cell No. TYPE OF MATERIAL DRY BULK DENSITY t/m MOISTURE CONTENT % APPLICATION PARTICLE DISTRIBUTION Light Duty Particle Medium Duty % Passing Heavy Duty X-Heavy Contact Person Email Date MAX FEED SIZE (mm) CAPACITY tph FLOWABILITY Good Fair Poor Enq.No:
DECK PREPARATION
Cut Size
Poly
Wire
Rubber
If wet screening, how much water is available and at what pressure? HOW IS THE SCREEN BEING FED? YES Conveyor Vibrating Feeder Is the material feed constant ? Feedbox COMMENTS/ NOTES NO
Head Office: 57 Jansen Road, Elandsfontein PO Box 8182 Elandsfontein,1406 Johannesburg South Africa www.osborn.co.za Tel: +27 11 820 7600 Fax: +27 11 388 1136 Call Centre: 0861 OSBORN E-mail: osborn@osborn.co.za
All rights reserved. Unless otherwise indicated, all materials on these pages are copyrighted by OSBORN. No part of these pages, either text or image may be used for any purpose other than personal use. Therefore, reproduction, modification, storage in a retrieval system or retransmission, in any form or by any means, electronic, mechanical or otherwise, for reasons other than personal use, is strictly prohibited without prior written permission.
www.osborn.co.za
www.telsmith.com
www.rockbreaker.com
www.astrcmobilescreens.com
www.kpijci.com
Vibrating Screen/0612/Rev1