Académique Documents
Professionnel Documents
Culture Documents
Copyright
This document is copyrighted, 2004, by Chenbro Micom Co., Ltd. All rights are reserved. Chenbro Micom Co., Ltd. reserves the right to make improvements to the products described in this manual at any time. Specifications are thus subject to change without prior notice.
No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of Chenbro Micom Co., Ltd. Information provided in this manual is intended to be accurate and reliable. However, Chenbro Micom Co., Ltd., assumes no responsibility for its use, nor for any infringements upon the rights of third parties, which may result from its use.
Technical Support
We want you to get the maximum performance from your products. So if you run into technical difficulties, we are here to help. For the most frequently asked questions, you can easily find answers in your product documentation. These answers are normally a lot more detailed than the ones we can give over the phone.
So please consult this manual first. If you still cannot find the answer, gather all the information or questions that apply to your problem, and with the product close at hand, call your dealer. Our dealers are well trained and ready to give you the support you need to get the most from your Chenbro products. In fact, most problems reported are minor and are able to be easily solved over the phone.
In addition, free technical support is available from Chenbro engineers every business day. We are always ready to give advice on application requirements or specific information on the installation and operation of any of our products.
http://www.chenbro.com
Hardware Specification
Host Interface HDD Interface Hot-Swap S-ATA2 S-ATA2 / SAS Yes, allows user to on line replace Hard Disk Drive LED indicates Hard Disk Drive status Display Power LED Blue ( When HDD is present ) Access LED Green (When HDD is busy ) Cooling Environment Monitor Four Fan connector Fan speed detect and Temperature detect Buzzer beeping in case of any event occurs ex. Fan speed Alarm System too low or/and temperature too high ( 55 or 65 selectable ), mute the beeping when pushed the mute SW S-ATA7*6 to host Connectors S-ATA22*6 ( for HDD ), Standard 4P Power connector x 2 for +5V, +12V from power supply Dimension Material 257(l) x 80(w) x 2.4(h) mm FR4 4 layer
http://www.chenbro.com
Backplane Layout
Backplane Connectors
Front view ( HDD slot IN )
HDD-1
HDD-4
HDD-2
HDD-5
HDD-3
HDD-6
J11
(1) [HDD1/HDD2/HDD3/HDD4/HDD5/HDD6] : Connect 22-pin SATA2 HDD (2) [J12] : Fan Fail LED output connector (to LED board) (3) [HDA1/HDA2/HDA3/HDA4/HDA5/HDA6] : Connect 7-pin SATA2 Host (4) [FAN1 / FAN2 / FAN3 / FAN4] : Fan connectors (5) [SW1] : Functionality / Mode Setting (6) [J11 / J8] : Power connectors (7) [J14] : Power Failure Input (8) [J15] : Power Failure Alarm Mute Output (9) [J4 / J7] : HDD Failure LED input (10) [J1] : External HDD Access LED input
http://www.chenbro.com
Pin Assignment
[FAN1 / FAN2 / FAN3 / FAN4] Pin 1 2 3 Def. GND +12V Sensor FAN Connector
[J11 / J8] Pin 1 2 3 4 Def. +12V GND GND +5V Power Connector
[SW1 (1,2,3,4)] DIP4 (FAN1) Monitoring ON OFF Enable Disable DIP5 (FAN2) Monitoring Enable Disable DIP6 (FAN3) Monitoring Enable Disable DIP7 (FAN4) Monitoring Enable Disable Function Switch
[SW1 (5)] DIP 5 Function Monitoring Temperature Setting ON 55 DegC* OFF 65 DegC
[J12] Pin 1 2 3 4 5 6 7 8 Def LED(+) LED(-) LED(+) LED(-) (+) (-) GND KEY External Global Fail Mute (Reserved) N/A Failure LED Output Power/Temp Fail LED Output FAN Fail LED
http://www.chenbro.com
Chenbro RM21706 / 6-Port SATA2/SAS Backplane Users Manual [J4 / J7] J4 1 2 3 4 Def HDD1_Fail HDD2_Fail HDD3_Fail HDD4_Fail J7 1 2 3 4 Def HDD5_Fail HDD6_Fail N/C N/C HDD Fail Input
[J1] Pin External Access HDD LED Input 1 4 7 10 13 16 HDD1_Act HDD2_Act HDD3_Act HDD4_Act HDD5_Act HDD6_Act 2 5 8 11 14 17 Pin SATA HDD Pin-11 Access LED Input HDD1_Act HDD2_Act HDD3_Act HDD4_Act HDD5_Act HDD6_Act 3 6 9 12 15 18 HDD1_PWR HDD2_PWR HDD3_PWR HDD4_PWR HDD5_PWR HDD6_PWR External HDD Access LED input Pin Power LED Mode only
Backplane Assembly
The Chenbro 6-Port SATA Backplane can be only assembly on Chenbro Server Chassis RM21706, please refer to the Chassis Quick Installation Guide for the necessary information.
http://www.chenbro.com
Backplane Wiring
1. Please use attached 6 pcs SATA2 cable from HOST to Backplane. 2. For the Fan connectors, please connect the middle Fan (3P3C) to the Backplane. 3. For the Fail LED output, please connect to the front panel LED board cable.
http://www.chenbro.com