Académique Documents
Professionnel Documents
Culture Documents
DEH-34
Model No. CX-977 Order No. CRT2624
DEH-340/XN/UC
ORDER NO.
CRT2759
DEH-340 DEH-3400
XN/UC XN/UC CONTENTS
1. 2. 3. 4. 5. 6. SAFETY INFORMATION ............................................3 EXPLODED VIEWS AND PARTS LIST .......................4 BLOCK DIAGRAM AND SCHEMATIC DIAGRAM ...12 PCB CONNECTION DIAGRAM ................................26 ELECTRICAL PARTS LIST ........................................34 ADJUSTMENT..........................................................41
XN/UC
- This service manual should be used together with the following manual(s):
Mech. Module Remarks S9 CD Mech. Module:Circuit Description, Mech.Description, Disassembly
7. GENERAL INFORMATION .......................................45 7.1 DIAGNOSIS ........................................................45 7.1.1 DISASSEMBLY .........................................45 7.1.2 CONNECTOR FUNCTION DESCRIPTION .......48 7.2 PARTS .................................................................49 7.2.1 IC................................................................49 7.2.2 DISPLAY ....................................................58 7.3 OPERATIONAL FLOW CHART ...........................59 7.4 CLEANING ..........................................................60 8. OPERATIONS AND SPECIFICATIONS.....................61
For details, refer to "Important symbols for good services" on the next page.
PIONEER CORPORATION
4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O.Box 1760, Long Beach, CA 90801-1760 U.S.A. PIONEER EUROPE NV Haven 1087 Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE.LTD. 253 Alexandra Road, #04-01, Singapore 159936
DEH-340,3400,34
AMRF ATT
IC 2 FM MPX
L ch 6 R ch 5
ANT ADJ
FMANT
COMP LDET
21 18
27 RFGND 26
ATT
IC 3 EEPROM
FMLOCL STIND SDBW DGND FMSD NL1 NL2 CE2 CE1
S S
76
NC
CK
SL
RF ADJ
LOCH 23 25 LOCL
VDD VCC
T T T T T L
PDIO
PCE2
PCE1
PCK
SL
LOCL
VCC
VDD
SD
Q410
7 17 20 22 10 19 14
24
11 12 15 16
13
D CONTROL UNIT
CN101 Q101
15 5 AC,BD F,E FO+ TO+ LD+ 4 1 14 FOP TOP VDD 9 8 LDO MDI RFRPIN FEO 24 16 38 43 46 RFI FEI TEI L_OUT 85 78
CN701
L-OUT
CN501
14 14
CDL
TEO 14
RF-AMP
IC 101 TA2153FN
12 FOP 14 TOP TD/FD SD/MD
79
IC 201 TC9495F2
SPINDLE MOTOR
CD DRIVER
16 SOP 15 SOM 17 LCOP 18 LCOM
LOEJ MUTE
22 9
LOEJ CONT
10 11
10 11
LOEJ CONT
34 23
LOEJ CONT
IC 401 BA5996FM
DSCSNS HOME
17 16
17 16
79 32
DSCSNS HOME
S901 HOME VD 12EJ DISC CLAMP SENSE 8EJ SENSE SENSE SENSE VDD
Q510
VD
2 VD
B.U
+5V REGULATOR
4
IC 701 BA05SFP
1
Q511
CD5VON
CD5VON
VDCONT
21
VDCONT
35
CD5VON
12 1 2 3 4
DEH-340,3400,34
A
DEH-340/XN/UC CN351
FRONT L CH Q 341
REAR L CH Q 351
Q359
VDD REGULATOR
SD SL VDD
Q913
B.U
TUNPCE TUNPCK TUNPCE2 TUNPDO TUNPDI LOCL VST VCK VDT VCC SYSPW
VCC REGULATOR
Q910 Q911
B.U
CN901
B.U BACKUP 2 FUSE 10A
Q912
B
2 BACK UP GND 1
IN2_L
POWER AMP
23 FLFL+ RLRL+ 10 11
ELECTRONIC VOLUME
3 IN3_L
10 12 9 11
10 12 9 11
IC 301 PML003AM
Frontout_L Rearout_L
14
FL 12 RL
IC 361 PAL007A
MUTE 22 STBY 4
21 3 5 25
FLFL+ RLRL+
SYSPW
Q921
Q361 MUTE
Q920
asens bsens ASENS 64 ACC 3 B.U 3 ACC
BSENS
63
ANTIN
52
TELIN
38
C
B.REM 6 6 B.REM
SYSPW
42
MUTE
44
RESET
60
VDD
NS
DSENS
64
S750 DSENS
B
CN750
ROT0 ROT1 CSENS KYDT DPDT 13 12 4 14 11 7 5 13 12 4 14 11 7 5
PANEL UNIT
C
4 6 10 ROT0 ROT1
KEYBOARD UNIT
CN1950 CN1951
9 7 3 8 10
37 36 80 8 9
CSENS 20 18
NT B.U ILMPW 40
Q751
ILB+ FILM+
ILLUMINATION
LCD ILLUMINATION
B.U
Q753
FLPILM EJECTS N SWVDD 20 53 VDD 41
Q752
FILM-
EJECT
IC 1900 PD6340A
Q750
GND
9 SW+5V
IC1902 RS-140
4 5 8
17
REM
D
KEY MATRIX
SW5V
10
10
56
VDD
10 VLCD
13 5 6 7 8
DEH-340,3400,34
A
A-a A-b
A-a
Large size SCH diagram
A-a A-b
Guide page
FM(100%):-19.5dBs AM(30%):-30dBs
272 272
A-a
A-b
Detailed page
162
183
183
162
ELECTRONIC
R791 0R0
SYST
ANTENNA JACK
CSS1023 4.194MHz 104 393
CONTROL UNIT
DSENS
KEYBOARD UNIT
EJECT
B
Ex. *Resistors Code Practical value 123 12k ohms 103 10k ohms
PANEL UNIT
For resistors and capacitors in the circuit diagrams, their resistance values or capacitance values are expressed in codes: *Capacitors Code Practical value 103 0.01uF 101/10 100uF/10V
14
A B
1
DEH-340,3400,34
A-b
A TUNER AMP UNIT
CD:+9.4dBs
DEH-340/XN/UC VOLUME
PRE OUT
FR FL
RR RL
MUTE
EM CONTROLLER
600H
POWER AMP
FM(100%):+29.6dBs AM(30%):+19.1dBs CD:+36.2dBs
CEK1136
>
10A
B.REM
VDD REGULATOR
RR+ FR+
BACK UP SENSE
ACC SENSE
A
8
15
183
162
162
CSS1023 4.194MHz
ELECTRONIC VOLU
DEH-340,3400,34
ANTENNA JACK
FM(100%):-19.5dBs AM(30%):-30dBs
16
A-a
2
R791 0R0
SYSTEM CO
A-a A-b
104
393
CONTROL UNIT
KEYBOARD UNIT
5
EJECT
2 3
DSENS
6 7
PANEL UNIT
For resistors and capacitors in the circuit diagrams, their resistance values or capacitance values are expressed in codes: *Capacitors Code Practical value 103 0.01uF 101/10 100uF/10V
Ex. *Resistors Code Practical value 123 12k ohms 103 10k ohms
DEH-340,3400,34
B A-a A
C
A-
17 A B
A-a A-b
B A
D C
18
A-a A-b
DEH-340,3400,34
A-b
A TUNER AMP UNIT
CD:+9.4dBs
DEH-340/XN/UC
PRE OUT
2
FR FL RR RL
C VOLUME
MUTE
3
600H
TEM CONTROLLER
POWER AMP
FM(100%):+29.6dBs AM(30%):+19.1dBs CD:+36.2dBs
CEK1136
>
10A
2
B.REM
3
VDD REGULATOR
RLFLRL+ FL+ RRFR-
RR+ FR+
BACK UP SENSE
ACC SENSE
DEH-340,3400,34
A-b
A-a A-b
A B C
19
DEH-340,3400,34
5 LCD
CLOC
20
C
1 2
DEH-340,3400,34
E CONTROL SENSOR
KEYBOARD UNIT
VOLUME
CSD1077
SOURCE EQ
B
CN1951
B
CLOCK
CSG1111
LOCAL
NSSW440-9159
BAND
LOUD
NSSW440-9159
BSM AUDIO
CSG1111
C
5 6 7 8
21
DEH-340,3400,34
CONTROL UNIT
PICKUP UNIT(SERVICE)(P9)
RF AMP
CN101
ACT/MOTOR DRIVER
5V REGULATOR
22
D
1 2
DEH-340,3400,34
SERVO CONTROL/DSP/DAC/LPF
16.934MHz
ER
SWITCHES: CONTROL UNIT S901 : HOME SWITCH.....ON-OFF S902 : CLAMP SWITCH....ON-OFF S903 : DSCSNS SWITCH....ON-OFF S904 : 12EJ SWITCH....ON-OFF S905 : 8EJ SWITCH....ON-OFF The underlined indicates the switch position.
Decimal points for resistor and capacitor fixed values are expressed as : 2.22R2 0.022R022
CN701
A
CN501
D
D
8
23
DEH-340,3400,34
Note:1. The encircled numbers denote measuring pointes in the circuit diagram. 2. Reference voltage VREF:2.1V
- Waveforms
1 2 3 4 CH1:DSCSNS 5V/div. CH2:CLCONT 5V/div. 500ms/div. CH3:LOEJ 5V/div. CH4:VD 10V/div. When loading (12 cm CD) 1 2 3 4 5 CH1:FD 500mV/div. CH1:DSCSNS 5V/div. 6 CH2:FOK 5V/div. 500ms/div. CH2:CLCONT 5V/div. 500ms/div. 7 CH3:MD 5V/div. CH3:LOEJ 5V/div. CH4:VD 10V/div. When setting up "Source On" When loading (8 cm CD) Ref. : VREF Mode : Normal
0 CH1:TE 8 CH2:FE
8 5 0 !
CH1:FE 500mV/div. CH2:FD 500mV/div. CH3:TE 500mV/div. CH4:TD 500mV/div. During "Play"
@ CH1:BCK 1ms/div.
2V/div.
10s/div.
During "Play"
7 CH1:MD
500mV/div.
10s/div. % CH1:RFO
During "Play"
500mV/div. 500mV/div. 0.5s/div. % CH1:RFO 0 CH2:TE 500mV/div. During "Play" During "Tracking Open"
2ms/div.
24
DEH-340,3400,34
5 CH1:FD ^ CH2:FOP
1V/div. 2V/div.
200ms/div.
5ms/div.
1 Track Jump
32 Track Jump
% 5ms/div. & 5 !
* CH1:TEY ( CH2:SD
During inside/outside search When "Eject" (12 cm CD) When "Eject" (8cm CD)
200s/div.
25
DEH-340,3400,34
(2) Error Code List Code Class Displayed error code Description of the code and potential cause(s) 10 Electricity Carriage Home NG CRG can't be moved to inner diameter. SERVO LSI ComCRG can't be moved from inner diameter. munication Error Failure on home switch or CRG move mechanism. 11 12 Electricity Electricity Focus Servo NG Spindle Lock NG Subcode NG Communication error between microcomputer and SERVO LSI. Focusing not available. Stains on rear side of disc or excessive vibrations on REWRITABLE. Spindle not locked. Sub-code is strange (not readable). Failure on spindle, stains or damages on disc, or excessive vibrations. A disc not containing CD-R data is found. Turned over disc are found, though rarely. CD signal error. AGC protection doesn't work. Focus can be easily lost. Damages or stains on disc, or excessive vibrations on REWRITABLE. Failed to reach target address. CRG tracking error or damages on disc. Skip setting for all track. (CD-R/RW) Mechanical error during CD ON. Defective loading motor, mechanical lock and mechanical sensor. A0 System Power Supply NG Power (VD) is ground faulted. Failure on SW transistor or power supply (failure on connector).
17 30 44 50
Remarks: Mechanical errors are not displayed (because a CD is turned off in these errors). Unreadable TOC does not constitute an error. An intended operation continues in this case. Upper digits of an error code are subdivided as shown below: 1x: Setup relevant errors, 3x: Search relevant errors, Ax: Other errors.
44
DEH-340,3400,34
- DEH-340/XN/UC
ANTENNA
PRE OUT
- DEH-3400/XN/UC, DEH-34/XN/UC
1. GND 2. BACK UP 3. ACC 4. NC 5. NC 6. B.REM 7. NC 8. NC 9. RL10. FL11. RL+ 12. FL+ 13. RR14. FR15. RR+ 16. FR+
48
DEH-340,3400,34
C C C C C C C C C C C C C C C C
C C C C C C C C C C C
49
DEH-340,3400,34
Pin No. 68 69 70 71 72 73 74 75 76 77 78 79 80
Pin Name VDD X2 X1 IC(VPP) NC TESTIN AVDD AVREF0 SL TEMP VDSENS DISCSNS CSENS
I/O
Format
I I I I I
Function and Operation Power supply Crystal oscillator connection pin Crystal oscillator connection pin Connect to GND Not used Test program mode input Positive power supply terminal for analog circuit A/D converter reference voltage SD level input from tuner CD temperature sense input VD power supply voltage sense input CD DISC sense input Flap open/close sense input
Output Format C
IC's marked by * are MOS type. Be careful in handling them because they are very liable to be damaged by electrostatic induction.
*PE5262A 80 1 61 60
20 21 40
41
50
DEH-340,3400,34
I O O O
*PD6340A
33
32
48 49 64 1
17 16
51
DEH-340,3400,34
- Pin Functions(TA2153FN)
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Pin Name VCC RFGC GMAD FNI FPI TPI TNI MDI LDO SEL TEB 2VRO TEN TEO SBAD FEO FEN SEB VRO RFRP BTC RFCT PKC RFRPIN RFGO GVSW AGCIN RFO GND RFN2 I/O I I I I I I O I I I O I O O O I I O O I O I I O I I O I I Function and Operation Power supply voltage terminal RF amplitude adjustment control signal terminal AGC amplifier frequency characteristic adjustment terminal Main beam amplifier input terminal Main beam amplifier input terminal Sub beam amplifier input terminal Sub beam amplifier input terminal Monitor photodiode amplifier input terminal Laser diode amplifier output terminal APC circuit ON/OFF signal, LDO terminal control input terminal and bottom and peak detection frequency switching terminals Tracking error balance adjustment signal input terminal Reference voltage (2VRO) output terminal Tracking error signal generation amplifier reverse phase input terminal Tracking error signal generation amplifier output terminal Sub beam addition signal output terminal Focus error signal generation amplifier output terminal Focus error signal generation amplifier reverse phase input terminal RFRP generation circuit mode switching terminal Reference voltage (VREF) output terminal Signal generation amplifier output terminal for track count Bottom detection time constant adjustment terminal for RFCT signal generation RFRP signal center level output terminal Peak detection time constant adjustment signal for RFCT signal generation Signal generation amplifier input terminal for track count RF signal amplitude adjustment amplifier output terminal AGC, FE or TE amplifier gain switching terminal RF signal amplitude adjustment amplifier input terminal RF signal generation amplifier output terminal GND terminal RF signal generation amplifier input terminal
TA2153FN
15
16
30
52
DEH-340,3400,34
- Pin Functions(TC9495F2)
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 Pin Name TESTO hso uhso EMPH LRCK VSS BCK AOUT DOUT MBOV IPF SBOK CLCK VDD VSS DATA SFSY SBSY SPCK SPDA COFS MONIT VDD TESIO0 P2VREF HSSW ZDET PDO TMAXS TAMX LPFN LPFO PVREF VCOREF VCOF AVSS SLCO RFI AVDD RFCT RFZI RFRP FEI SBAD TSIN TEI TEZI FOO TRO VREF RFGC TEBC FMO FVO DMO 2VREF SEL I/O O O O O O O O O O O I/O Function and Operation Test mode terminal Replay speed flag output terminal Replay speed flag output terminal Emphasis flag output terminal for sub code Q data Channel clock (44.1 kHz) output terminal Digital ground terminal Bit clock output terminal Digital audio data output terminal Digital out output terminal Buffer memory over signal output terminal Correction flag output terminal CRCC decision result output for sub code Q data Clock input/output terminal for sub code P-W data read Digital + power supply terminal (5 V) Digital ground terminal Sub code P-W data output terminal Replay-system frame sync signal output terminal Sub code block sync output terminal Clock for processor status signal read Processor status signal output terminal Correction-system frame clock (7.35 kHz) output terminal LSI internal signal output terminal Digital + power supply terminal (5 V) Test input/output terminal PLL-system only 2VREF terminal The VREF voltage is reached for double or quad speed. One-bit DAC zero detection flag output terminal Phase error signal issue between the EFM and PLCK signals TMAX detection result output terminal TMAX detection result output terminal Reverse input terminal of amplifier for lowpass filter Output terminal of amplifier for lowpass filter PLL-system only VREF terminal VCO center frequency reference level terminal Filter terminal for VCO Analog-system ground terminal Output terminal of DAC for data slice level generation RF signal input terminal Analog-system power supply terminal (5 V) RFRP signal center level input terminal Input terminal for RFRP signal zero cross RF ripple signal input terminal Focus error signal input terminal Sub beam addition signal input terminal Test input terminal Tracking error input terminal Input terminal for tracking error or zero cross Focus equalizer output terminal Tracking equalizer output terminal Analog reference power supply terminal RF amplitude adjustment control signal output terminal Tracking balance control signal output terminal Feed equalizer output terminal Speed error signal or feed search EQ output Disc equalizer output terminal Analog reference power supply terminal APC circuit ON/OFF signal output terminal
O O O O O O O I O O O O O I O I O O I I I I I I I I I O O O O O O O O
53
DEH-340,3400,34
Pin Name FLGA-D VDD VSS IO0 IO1 IO2 IO3 dmout ckse dact TESIN TESIO1 VSS PXI PXO VDD XVSS XI XO XVDD DVSR RO DVDD DVR LO DVSL TEST1-3 BUS0-3 VDD VSS BUCK cee TEST4 tsmod rst
I/O O
O O I O I I I I I I O
I O
O I I/O
I I I I I
Function and Operation External flag output terminal for internal signal monitor Digital + power supply terminal (5 V) Digital ground terminal RF amplifier gain switching terminal Not used HOME detection switch input terminal FocusDrv and signal output terminal Field equalizer PWM output terminal for IO0 and IO1 Disc equalizer PWM output terminal for IO2 and IO3 Usually open DAC test mode terminal Test input terminal Test input/output terminal Digital ground terminal DPS-system clock oscillator circuit input terminal DPS-system clock oscillator circuit output terminal Digital + power supply terminal (5 V) Ground terminal for system clock oscillator circuit System clock oscillator circuit input terminal System clock oscillator circuit output terminal For system clock oscillator circuit + power supply terminal R channel D/A converting unit power supply terminal R channel data forward rotation output terminal D/A converting unit power supply terminal (5 V) Reference voltage terminal L channel forward rotation output terminal L channel D/A converting unit power supply terminal Test mode terminal Data input/output terminal for microcomputer interface Digital + power supply terminal (5 V) Digital ground terminal Clock terminal for microcomputer interface Chip enable signal for microcomputer interface Test mode terminal Test mode terminal Reset signal input terminal
31 30 1 100
54
DEH-340,3400,34
- Pin Functions(BA5996FM)
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Pin Name VR OPIN2(+) OPIN2(-) OPOUT2 OPIN1(+) OPIN1(-) OPOUT1 GND MUTE POWVCC1 VO1(-) VO1(+) VO2(-) VO2(+) VO3(+) VO3(-) VO4(+) VO4(-) POWVCC2 GND CNT LDIN OPOUTSL OPINSL OPOUT3 OPIN3(-) OPIN3(+) PREVCC Function and Operation Input pin for reference voltage Input pin for non-inverting input for CH2 preamplifier Input pin for inverting input for CH2 preamplifier Output pin for CH2 preamplifier Input pin for non-inverting input for CH1 preamplifier Input pin for inverting input from CH1 preamplifier Output pin for CH1 preamplifier Ground pin Mute control pin Power supply pin for CH1, CH2, and CH3 at "Power" stage Driver CH1 - Negative output Driver CH2 - Positive output Driver CH2 - Negative output Driver CH2 - Positive output Driver CH2 - Positive output Driver CH2 - Negative output Driver CH4 - Positive output Driver CH4 - Negative output Power supply pin for CH4 at "Power" stage Ground pin Control pin Loading input Output pin for preamplifier for thread Input pin for preamplifier for thread CH3 preamplifier output pin Input pin for inverting input for CH3 preamplifier Input pin for non-inverting input for CH3 preamplifier PreVcc
BA5996FM
14
15
28
55
DEH-340,3400,34
PAL007A
sw_vcc
1
amp_vcc Stand-by Circuit
TAB P-GND2 OUT2STBY OUT2+ VCC OUT1P-GND1 OUT1+ SVR IN1 IN2 S-GND IN4 IN3 AC-GND OUT3+ P-GND3 OUT3VCC OUT4+ MUTE OUT4P-GND4 SWITCH
Reference
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
Mute circuit
+-
Offset Detection
Protector; Thermal
-+ +-
Offset Detection
-+
amp_vcc
+-
Offset Detection
-+ +-
Offset Detection
-+
sw_vcc
stby
56
DEH-340,3400,34
ATT
ANT ADJ
FMANT
COMP LDET
21 18
27 RFGND 26
IC 3 EEPROM
FMLOCL SDBW DGND FMSD DI/DO NL1 NL2 4 CE2 CE1 STIND 1
NC
CK
LOCH 23 25
LOCL
7 17 20 22 10 19 14
24
11 12 15 16
SL 13
RF ADJ
CREQ
VDD VCC
No. Symbol I/O Explain 1 STIND O stereo indicator 2 FMSD O FM station detector
"Low" when the FM stereo signals are received. To be pulled up to the "VDD" at 47k. "High" when signals are received. To be pulled up to the "VDD" at 47k Meanwhile, 10k should be used when taking diver FIX trigger from here and "High: 0.9VDD or more" and "Low: 250mV or less". (Should satisfy the diver IC specifications) 3 NL1 O noise level-1 "High" when noise is received. Output for the RDS. GND at 47k //1,800pF. 4 NL2 O noise level-2 "High" when noise is received. Output for the RDS. GND at 36k //330pF. 5 Rch O R channel FM stereo "R-ch" signal output or AM audio output. output Add the specified de-emphasis constant. 6 Lch O L channel FM stereo "L-ch" signal output or AM audio output. output Add the specified de-emphasis constant. 7 WC write control EEPROM write control. Writing permissible at "Low". Normally open. 8 SDBW O SD bandwidth SD bandwidth signal output. For detection of detuning data for the RDS. 9 NC Not used 10 VDD power Power supply pin for the digital section. supply DC 5V +/- 0.25V. Be careful about overlapping noise in the logic section. 11 DGND digital ground Grounding for the digital section. 12 CE2 I chip enable-2 EEPROM chip enable. Active a "Low" To be pulled up to the "VDD" at 47k 13 SL I/O signal level Received FM/AM signal level (strength) output. Connect the specified load resistor and capacitor (10k + 39k //4,700pF) 14 DI/DO I/O data input/ Data input/Data output data output To be pulled up to the "VDD" at 47k 15 CK I clock Clock input To be pulled up to the "VDD" at 47k 16 CE1 I chip enable-1 AFRF chip enable. Active at "High" To be grounded at 47k 17 NC Not used 18 LDET O lock detector Active at "Low". To be pulled up to the "VDD" at 47k 19 CREQ I current request Active at "Low". To be grounded at 47k 20 NC Not used 21 COMP O composite signal FM composite signal output. r out < 100 22 VCC power supply Analog section power supply pin.DC 8.4V +/- 0.3V 23 LOCH I local high FM local high pin. When seeking local high, apply 5V together with "LOCL". 24 FMLOCL I FM local low FM local low pin. When seeking local low, apply 5V to the base of the NPN transistor with which the specified resistor is being connected to the emitter. Keep it open in case of ordinary marketed models. 25 LOCL I local low FM/AM local low pin. When seeking local low, apply 5V to the base of the NPN transistor. Since this pin is exclusive for AM when the FMLOCL is in use, do not drive it under FM. 26 RFGND RF ground Grounding for the antenna section. 27 FMANT I FM antenna input FM antenna input. 75. Surge absorber (DSP-201M-S00B) is necessary. 28 AMANT I AM antenna input AM antenna input. High impedance. Connect to the antenna through an L (LAU type) of 4.7H.To cope with the power transmission line hums, insert a series circuit consisting of an L (a coil of about 100mH) + R (a resistor of 470 to 2.2k) between the GND.
57
COM2A COM1A COM2B COM0A COM2C COM3A COM2D COM3B COM2E COM1B COM0B
COM2A COM1A COM2B COM0A COM2C COM3A COM2D COM3B COM2E COM1B COM0B 38 37 39 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 36
51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
DEH-340,3400,34
58
7.2.2 DISPLAY
COMMON
SEGMENT
DEH-340,3400,34
VDD=5V Pin 68
bsens Pin 63 BSENS=L asens Pin 64 ASENS=L dsens Pin 65 DSENS=L ADPWH Pin 66
- CSENS 2V, 3V CSENS Source returns to the original one(before you open). CD loading functions are available. Keys except for EJECT key are not available.
Starts communication with Grille microcomputer. 300ms swvddL Pin 41 Source keys operative
300ms In case of the above signal, the communication with Grille microcomputer may fail. If the time interval is not 300msec, the oscillator may be defective.
Source ON
SYSPWH Pin 42
59
DEH-340,3400,34
7.4 CLEANING
Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools:
60
DEH-340,3400,34
@ !
4 5
0
Whats what
1 BSM button Press and hold for two seconds to switch BSM function on or off. 2 LOCAL button Press to switch local function on or off. 3 OPEN button Press to open the front panel. 4 AUDIO button Press to select various sound quality controls. 5 5//2/3 buttons Press to do manual seek tuning, fast forward, reverse and track search controls. Also used for controlling functions. 6 LOUDNESS button Press to switch loudness function on or off.
7 BAND button Press to select among three FM and one AM band and cancel the control mode of functions. 8 16 (PRESET TUNING) buttons Press for preset tuning. 9 SOURCE button This unit is switched on by selecting a source. Press to cycle through all of the available sources. 0 EQ button Press to select various equalizer curves. ! VOLUME Rotate to increase or decrease the volume. @ CLOCK button Press to switch clock display on or off.
Remote control
# 7 $ % ^ * 4 & 5
A remote controller that enables remote operation of the head unit is supplied. Operation is the same as when using the button on the head unit. See the explanation of the head unit about the operation of each button with the exception of ATT, which is explained below. # +/ button Raise or lower the volume. $ FUNCTION button Not used. % CD button Press once to select a CD. ^ PAUSE button Press once to pause play. & TUNER button Press once to select a tuner. * ATT button Press to quickly lower the volume level, by about 90%. Press once more to return to the original volume level.
61
DEH-340,3400,34
62
Tuner
Listening to the radio Playing a CD
2 Use VOLUME to adjust the sound level. Rotate to increase or decrease the volume.
Press SOURCE to turn the unit on. When you select a source the unit is turned on.
1 1 2
3 4
3 Press BAND to select a band. Press BAND until the desired band is displayed, F1, F2, F3 for FM or AM.
Selecting a source
1 TRACK NUMBER indicator Shows the track currently playing. 2 PLAY TIME indicator Shows the elapsed playing time of the current track. 1 Press OPEN to open the front panel. CD loading slot appears. 2 Insert a CD into the CD loading slot. Playback will automatically start. CD loading slot
4 To perform manual tuning, press 2 or 3 1 BAND indicator with quick presses. Shows which band the radio is tuned to, The frequencies move up or down step by You can select a source you want to listen AM or FM. to. To switch to the built-in CD player, load a step. disc in this unit. 2 FREQUENCY indicator 5 To perform seek tuning, press and hold 2 Shows to which frequency the tuner is Press SOURCE to select a source. or 3 for about one second and release. tuned. Press SOURCE repeatedly to switch between The tuner will scan the frequencies until a the following sources: broadcast strong enough for good reception 3 PRESET NUMBER indicator Built-in CD playerTuner is found. Shows what preset has been selected. You can cancel seek tuning by pressing either 2 or 3 with a quick press. Notes 4 STEREO () indicator If you press and hold 2 or 3 you can skip Shows that the frequency selected is When no disc is set in this product, built-in broadcasting stations. Seek tuning starts as being broadcast in stereo. CD player source will not change. soon as you release the buttons. When this units blue/white lead is connected to the cars auto-antenna relay Note control terminal, the cars antenna extends when this units source is When the frequency selected is being switched on. To retract the antenna, broadcast in stereo the STEREO () indicaswitch the source off. tor will light.
CD EJECT button
Press SOURCE and hold for at least one second to turn the unit off.
After a CD has been inserted, press SOURCE to select the built-in CD player.
Built-in CD player
Repeating play
Repeat play lets you hear the same track over again. 1 Press 5 to turn repeat play on. RPT appears in the display. The track presently playing will play and then repeat.
Audio Adjustments
Introduction of audio adjustments Using balance adjustment
You can select a fader/balance setting that provides an ideal listening environment in all occupied seats.
4 Use VOLUME to adjust the sound level. Rotate to increase or decrease the volume.
6 To skip back or forward to another track, press 2 or 3. Pressing 3 skips to the start of the next track. Pressing 2 once skips to the start of the current track. Pressing again will skip to the previous track.
2 Press 5 to turn repeat play off. The track presently playing will continue to 1 AUDIO display play and then play the next track. Shows the audio adjustments status. Note 2 LOUD indicator Appears in the display when loudness is turned on.
1 Press AUDIO to select FAD. Press AUDIO until FAD appears in the display. If the balance setting has been previously adjusted, BAL will be displayed.
Notes
2 Press 5 or to adjust front/rear speaker balance. Each press of 5 or moves the front/rear speaker balance towards the front or the rear. FAD F15 FAD R15 is displayed as the front/rear speaker balance moves from front to rear. FAD 0 is the proper setting when only two speakers are used.
Press AUDIO to display the audio function names. Press AUDIO repeatedly to switch between the following audio functions: FAD (balance adjustment)EQ-L (equalizer)LOUD (loudness)FIE (front image enhancer)SLA (source level adjustment) When selecting the FM tuner as the source, you cannot switch to SLA. To return to the display of each source, press BAND. Note If you do not operate the audio function within about 30 seconds, the display is automatically returned to the source display.
The built-in CD player plays one, standard, If you perform track search or fast forward/reverse, repeat play is automati12-cm or 8-cm (single) CD at a time. Do cally cancelled. not use an adapter when playing 8-cm CDs. Do not insert anything other than a CD into the CD loading slot. If you cannot insert a disc completely or if Pausing CD playback after you insert a disc the disc does not play, check that the label side of the disc is Pause lets you temporarily stop playback of the CD. up. Press CD EJECT to eject the disc, and check the disc for damage before inserting 1 Press 6 to turn pause on. the disc again. PAUSE appears in the display. Play of the If the built-in CD player does not operate properly, an error message such as ERROR- current track pauses. 14 may be displayed. 2 Press 6 to turn pause off. Play will resume at the same point that you turned pause on.
3 Press 2 or 3 to adjust left/right speaker balance. When you press 2 or 3, BAL 0 is displayed. Each press of 2 or 3 moves the left/right speaker balance towards the left or the right. BAL L9 BAL R9 is displayed as the left/right speaker balance moves from left to right.
Random play lets you play back tracks on the CD in a random order.
1 Press 4 to turn random play on. RDM appears in the display. Tracks will play in a random order.
DEH-340,3400,34
2 Press 4 to turn random play off. Tracks will continue to play in order.
63
DEH-340,3400,34
64
Audio Adjustments
Adjusting equalizer curves
Switch the F.I.E. function OFF when using a 2-speaker system. 2 Select LOUD on or off with 5/.
You can adjust the currently selected equalThe equalizer lets you adjust the equaliza3 Select the desired level with 2/3. izer curve setting as desired. Adjusted tion to match car interior acoustic characterLOW (low) MID (mid) HI (high) equalizer curve settings are memorized in istics as desired. CUSTOM.
There are six stored equalizer curves which you can easily recall at any time. Here is a list of the equalizer curves: 2 Select the band you want to adjust with the 2/3. EQ-L (low) EQ-M (mid) EQ-H (high)
Note 1 Press AUDIO to select the equalizer mode. You can also switch LOUD on or off by Press AUDIO until EQ-L/EQ-M/EQ-H appears in pressing the LOUDNESS. the display.
Display
Equalizer curve
SPR-BASS
Super bass
POWERFUL
Powerful
NATURAL
Natural
VOCAL
Vocal
CUSTOM
Custom
The F.I.E. (Front Image Enhancer) function is a simple method of enhancing front imaging by cutting mid- and high-range frequency output from the rear speakers, limiting their output to low-range frequencies. You can select the frequency you want to cut.
EQ FLAT
Flat
CUSTOM is an adjusted equalizer curve that you create. When EQ FLAT is selected no supplement or correction is made to the sound. This is useful to check the effect of the equalizer curves by switching alternatively between EQ FLAT and a set equalizer curve.
3 Press 5 or to adjust the equalizer curve. Each press of 5 or increases or decreases the equalizer curve respectively. +6 6 is displayed as the equalizer curve is increased or decreased. The actual range of the adjustments are different depending on which equalizer curve is selected.
3 Press 5 or to adjust the source volume. Each press of 5 or increases or decreases the source volume. SLA +4 SLA 4 is displayed as the source Precaution When the F.I.E. function is deactivated, the volume is increased or decreased. rear speakers output sound of all frequenNote cies, not just bass sounds. Reduce the If you make adjustments when a curve Notes volume before disengaging F.I.E. to preother than CUSTOM is selected, the newly Since the FM tuner volume is the control, vent a sudden increase in volume. adjusted curve will replace the previous it is not possible to apply source level curve. Then a new curve with CUSTOM adjustments to the FM tuner. 1 Press AUDIO to select FIE. appears on the display while selecting the Press AUDIO until FIE appears in the display. The AM tuner volume level can also be equalizer curve. adjusted with source level adjustments. 2 Select FIE on or off with 5/. 3 Select the desired frequency with 2/3. 100160250 (Hz) Notes
Press EQ to select the equalizer. If the equalizer has been previously set to an equalizer curve other than POWERFUL then the title of that previously selected equalizer curve will be displayed, such as SPR-BASS, NATURAL, VOCAL, CUSTOM, or EQ FLAT.
Adjusting loudness
Loudness compensates for deficiencies in the low- and high-sound ranges at low volume. 1 Press AUDIO to select LOUD. Press AUDIO until LOUD appears in the display.
After switching the F.I.E. function ON, select the Fader/Balance mode in the Audio Menu, and adjust front and rear speaker volume levels until they are balanced.
- DEH-340/XN/UC
Connecting cords with RCA pin plugs (sold separately) Power amp (sold separately)
This Product
Antenna jack Blue/white To system control terminal of the power amp or Auto-antenna relay control terminal (max. 300 mA 12 V DC).
Front output
Yellow To terminal always supplied with power regardless of ignition switch position.
Black (ground) To vehicle (metal) body. With a 2 speaker system, do not connect anything to the speaker leads that are not connected to speakers.
Front speaker
Front speaker
Left
Right
Rear speaker
Rear speaker
DEH-340,3400,34
65
DEH-340,3400,34
8.2 SPECIFICATIONS
General
Power source .................. 14.4 V DC (10.8 15.1 V allowable) Grounding system .......... Negative type Max. current consumption ......................................... 10.0 A Backup current................. 5 mA Dimensions (W H D): (DIN) Chassis .............. 178 50 157 mm (7 2 6-1/8 in) Nose .................. 188 58 19 mm (7-3/8 2-1/4 3/4 in) (D) Chassis .............. 178 50 162 mm (7 2 6-3/8 in) Nose .................. 170 48 14 mm (7 1-7/8 1/2 in) Weight ...................... 1.5 kg (3.3 lbs)
CD player
System ............................ Compact disc audio system Usable discs .................... Compact disc Signal format: Sampling frequency 44.1 kHz Number of quantization bits .................................. 16; linear Frequency characteristics ......................................... 5 20,000 Hz (1 dB) Signal-to-noise ratio ....... 94 dB (1 kHz) (IHF-A network) Dynamic range ................ 92 dB (1 kHz) Number of channels ....... 2 (stereo)
FM tuner
Frequency range ............. 87.9 107.9 MHz Usable sensitivity ........... 9 dBf (0.8 V/75 , mono, S/N: 30 dB) 50 dB quieting sensitivity 15 dBf (1.5 V/75 , mono) Signal-to-noise ratio ....... 70 dB (IHF-A network) Distortion ........................ 0.3% (at 65 dBf, 1 kHz, stereo) Frequency response ....... 30 15,000 Hz (3 dB) Stereo separation ........... 40 dB (at 65 dBf, 1 kHz) Selectivity ....................... 70 dB Three-signal intermodulation (desired signal level) ..... 30 dBf (two undesired signal level: 100 dBf)
Audio
Continuous power output is 22 W per channel min. into 4 ohms, both channel driven 50 to 15,000 Hz with no more than 5% THD. Maximum power output 50 W 4 Load impedance ............. 4 (4 8 allowable) Preout max output level/output impedance ......................................... 2.2 V/1 k Equalizer (3-Band Equalizer): (LOW) ....................... Level : 12 dB (MID) ........................ Level : 12 dB (HIGH) ...................... Level : 12 dB Loudness contour (LOW) ....................... +3.5 dB (100 Hz), +3 dB (10 kHz) (MID) ........................ +10 dB (100 Hz), +6.5 dB (10 kHz) (HIGH) ...................... +11 dB (100 Hz), +11dB (10 kHz) (volume : 30 dB)
AM tuner
Frequency range ............. 530 1,710 kHz (10 kHz) Usable sensitivity ........... 18 V (S/N: 20 dB) Selectivity ....................... 50 dB (10 kHz)
Note Specifications and the design are subject to possible modifications without notice due to improvements.
Service Manual
HIGH POWER CD PLAYER WITH FM/AM TUNER
ORDER NO.
CRT2788
DEH-340 DEH-3400
XM/UC
XM/UC
DEH-34
Model No. DEH-340/XN/UC CX-977
XM/UC
- This service manual should be used together with the manual(s) listed below. For the parts numbers, adjustments, etc. which are not shown in this manual, refer to the following manual(s).
Order No. CRT2759 CRT2624 Mech. Module Remarks S9
CD Mech. Module:Circuit Description, Mech.Description, Disassembly
* : Non spare part Part No. DEH-340/XN/UC DEH-340/XM/UC CEG1116 Not used CHG4550 CHG4532 CHL4550 CHL4532 CHP2251 CHP2421 CHP2252 CHP2422
PIONEER CORPORATION
4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O.Box 1760, Long Beach, CA 90801-1760 U.S.A. PIONEER EUROPE NV Haven 1087 Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE.LTD. 253 Alexandra Road, #04-01, Singapore 159936
DEH-340,3400,34
EXTERIOR(DEH-340/XN/UC)(Page 6)
- EXTERIOR SECTION PARTS LIST
Mark No. Symbol and Description 11 Holder DEH-340/XN/UC CNC8659 Part No. DEH-340/XM/UC CXB6681(Holder Unit)
EXTERIOR(DEH-3400/XN/UC, DEH-34/XN/UC)(Page 8)
- EXTERIOR SECTION PARTS LIST
Mark No. Symbol and Description 11 Holder DEH-3400/XN/UC CNC8659 Part No. DEH-3400/XM/UC CXB6681(Holder Unit)