Académique Documents
Professionnel Documents
Culture Documents
Mar 3, 2005
Final Revision
******
F-51852GNFQJ-LW-AAN
T.Yuchi
Prepared by (ACI Engineering Division)
Table of Contents
1. General Specifications .................................................................................................................................. 2 2. Electrical Specifications ............................................................................................................................... 3 3. Optical Specifications ................................................................................................................................. 13 4. I/O Terminal .................................................................................................................................................... 15 5. Test ................................................................................................................................................................... 17 6. Appearance Standards ................................................................................................................................ 18 7. Code System of Production Lot ............................................................................................................... 21 8. Type Number.................................................................................................................................................. 21 9. Applying Precautions .................................................................................................................................. 21 10. Precautions Relating Product Handling................................................................................................ 22 11. Warranty ........................................................................................................................................................ 23
Revision History
Rev. Date Page Comment
OPTREX CORPORATION
Page 1/23
1. General Specifications
Operating Temp. Storage Temp. Dot Pixels Dot Size Dot Pitch Viewing Area Outline Dimensions
: : : : : : :
min. -20C ~max. 70C min. -30C ~max. 80C 128 (W) 64 (H) dots 0.47 (W) 0.47 (H) mm 0.50 (W) 0.50 (H) mm 69.0 (W) 36.5 (H) mm 89.7 (W) 49.8* (H) 11.8 (D) mm * Without Flat Cable and LED Cable 41.2g max. NTD-22662 ( F-STN / Black &White-mode / Transmissive ) 6:00 8-bit parallel data transfer Serial data transfer LED Backlight / White Vivid Color Display Specification (High Performance Color is Used) Dimensional Outline UE-312339
: :
: :
: :
: :
To our best knowledge, this product satisfies material requirement of RoHS regulation. Our company is doing the best efforts to obtain the equivalent certificate from our suppliers.
OPTREX CORPORATION
Page 2/23
2. Electrical Specifications
2.1. Absolute Maximum Ratings VSS=0V Parameter Supply Voltage (Logic) Supply Voltage (Booster Circuit) Symbol VDD-VSS VSS2 Conditions With Double *1 With Triple *1 With Quad *1 *1 *1 Min. -0.3 -7.0 -6.0 -4.5 -18.0 V5 -0.3 -0.3 Max. 7.0 +0.3 +0.3 +0.3 +0.3 +0.3 VDD +0.3 VDD +0.3 Units V V
Supply Voltage 1 V5, VOUT (LCD Drive) Supply Voltage 2 V1, V 2, V 3, V (LCD Drive) 4 Input Voltage VIN Output Voltage VO
V V V V
*1 Relative to VDD. The relation of VDD V1V2V3V4V5>VOUT ;VDD >VSSVOUT must be maintained. In case of inputting external LCD driving voltage, LCD drive voltage should start supplying toNJU6676 at the mean time of turning on VDD power supply or after turned on VDD. In use of the voltage boost circuit, the condition that the supply voltage : 18V VDD-VOUT is necessary. Decoupling capacitor should be connected between VDD and VSS due to the stabilized operation for the voltage converter. 2.2. DC Characteristics Ta=25C, VSS=0V Parameter Symbol Conditions *2 *2 *2 *2 With Triple *2 With Quad *2 VOUT VOUT2 V5 VREG% VIH VIL *2 Voltage converter off External power supply Voltage regulator off External power supply VDD =3.0V Min. 2.2 -6.0 -18.0 0.4 V5 V5 -6.0 -4.5 -18.0 -18.0 -18.0 0.8 VDD VSS Typ. Max. 5.5 -2.5 -6.0 VDD 0.6 V5 -2.5 -2.5 -6.0 -6.0 3.0 VDD 0.2 VDD V V V % V V Units V V V V V V Supply Voltage VDD-VSS (Logic) *1 Supply Voltage (Booster Circuit) Supply Voltage (LCD Drive) Supply Voltage (Booster Circuit) Booster Output Voltage Voltage Regulator Operating Voltage Voltage Follower Operating Voltage Base Voltage "High" Level Input Voltage "Low" Level Input Voltage VSS2 V5 V1, V 2 V 3, V 4 VSS2
OPTREX CORPORATION
Page 3/23
"High" Level Output Voltage "Low" Level Output Voltage Supply Current
1.06
V V mA
*1 Although the NJU6676 can operate in wide range of the operation voltage, it shall not be guaranteed in a sudden voltage fluctuation during the access with MPU. *2 Relative to VDD.
OPTREX CORPORATION
Page 4/23
2.3. AC Characteristics 2.3.1. Read/Write Operation Sequence (80 series CPU) VDD =4.5~5.5V Parameter Address Hold Time Address Setup Time System Cycle Time Control Low Pulse Width(Write) Control Low Pulse Width(Read) Control High Pulse Width(Write) Control High Pulse Width(Read) Data Setup Time Data Hold Time RD Access Time Output Disable Time Input Signal Rise/Fall Time Parameter Address Hold Time Address Setup Time System Cycle Time Control Low Pulse Width(Write) Control Low Pulse Width(Read) Control High Pulse Width(Write) Control High Pulse Width(Read) Data Setup Time Data Hold Time RD Access Time Output Disable Time Input Signal Rise/Fall Time Parameter Address Hold Time Address Setup Time System Cycle Time Control Low Pulse Width(Write) Control Low Pulse Width(Read) Control High Pulse Width(Write) Control High Pulse Width(Read) Data Setup Time
F-51852GNFQJ-LW-AAN (AA) No. 2005-0262
Symbol
Min. 0 0 166 30 70 30 30 30 10 10 Min. 0 0 300 60 120 60 60 40 15 10 Min. 0 0 1000 120 240 120 120 80
tAH8 tAW8 tCYC8 tCCLW tCCLR tCCHW tCCHR tDS8 tDH8 tACC8 tOH8 tr, tf
Symbol
tAH8 tAW8 tCYC8 tCCLW tCCLR tCCHW tCCHR tDS8 tDH8 tACC8 tOH8 tr, tf
Symbol
OPTREX CORPORATION
Data Hold Time RD Access Time Output Disable Time Input Signal Rise/Fall Time
30 10 -
280 200 15
ns ns ns ns
tCYC 8
A0, CS1
t AW 8 tCCL
WR, RD
t AH8
D0 D7 (WRITE)
tf
D0 D7 (READ)
OPTREX CORPORATION
Page 6/23
2.3.2. Read/Write Operation Sequence (68 series CPU) VDD =4.5~5.5V Parameter Address Hold Time Address Setup Time System Cycle Time Enable High Pulse Width (Read) Enable High Pulse Width (Write) Enable Low Pulse Width (Read) Enable Low Pulse Width (Write) Data Setup Time Data Hold Time Access Time (CL=100pF) Output Disable Time Input Signal Rise/Fall Time Parameter Address Hold Time Address Setup Time System Cycle Time Enable High Pulse Width (Read) Enable High Pulse Width (Write) Enable Low Pulse Width (Read) Enable Low Pulse Width (Write) Data Setup Time Data Hold Time Access Time (CL=100pF) Output Disable Time Input Signal Rise/Fall Time Parameter Address Hold Time Address Setup Time System Cycle Time Enable High Pulse Width (Read) Enable High Pulse Width (Write) Enable Low Pulse Width (Read) Enable Low Pulse Width (Write) Data Setup Time
F-51852GNFQJ-LW-AAN (AA) No. 2005-0262
Symbol
Min. 0 0 166 70 30 30 30 30 10 10 Min. 0 0 300 120 60 60 60 40 15 10 Min. 0 0 1000 240 120 120 120 80
tAH6 tAW6 tCYC6 tEWHR tEWHW tEWLR tEWLW tDS6 tDH6 tACC6 tOH6 tr, tf
Symbol
tAH6 tAW6 tCYC6 tEWHR tEWHW tEWLR tEWLW tDS6 tDH6 tACC6 tOH6 tr, tf
Symbol
OPTREX CORPORATION
Data Hold Time Access Time (CL=100pF) Output Disable Time Input Signal Rise/Fall Time
30 10 -
280 200 15
ns ns ns ns
tCYC6
RD (E)
t EW L
tEW H t AW 6
WR (R/W)
tr
tf t AH6
A0, CS1
t DS6
D0 D7 (WRITE)
tDH6
tACC6
D0 D7 (READ)
tOH6
OPTREX CORPORATION
Page 8/23
2.3.3. Serial Interface Sequence VDD =4.5~5.5V Parameter Serial Clock Cycle Serial Clock High Pulse Width Serial Clock Low Pulse Width Address Setup Time Address Hold Time Data Setup Time Data Hold Time CS-SCL Time Symbol Min. 200 75 75 50 100 50 50 100 100 Min. 250 100 100 150 150 100 100 150 150 Min. 400 150 150 250 250 150 150 250 250 Max. 15 Max. 15 Max. 15 Units ns ns ns ns ns ns ns ns ns ns VDD =2.7~4.5V Parameter Serial Clock Cycle Serial Clock High Pulse Width Serial Clock Low Pulse Width Address Setup Time Address Hold Time Data Setup Time Data Hold Time CS-SCL Time Symbol Units ns ns ns ns ns ns ns ns ns ns VDD =2.2~2.7V Parameter Serial Clock Cycle Serial Clock High Pulse Width Serial Clock Low Pulse Width Address Setup Time Address Hold Time Data Setup Time Data Hold Time CS-SCL Time Symbol Units ns ns ns ns ns ns ns ns ns ns
tSCYC tSHW tSLW tSAS tSAH tSDS tSDH tCSS tCSH tr, tf
tSCYC tSHW tSLW tSAS tSAH tSDS tSDH tCSS tCSH tr, tf
tSCYC tSHW tSLW tSAS tSAH tSDS tSDH tCSS tCSH tr, tf
OPTREX CORPORATION
Page 9/23
t CSS
CS1
t CSH
tSAS
A0
t SAH
t SCYC t SLW
D6(SCL)
D7(SI)
tf
OPTREX CORPORATION
Page 10/23
2.3.4. Display Control Timing Characteristics Reset Input Timing Parameter Reset time Reset L Pulse Width Reset Input Timing Parameter Reset time Reset L Pulse Width Reset Input Timing Parameter Reset time Reset L Pulse Width Symbol Min. 1.5 Typ. Max. 1.5 Symbol Min. 1 Typ. Max. 1 Symbol Min. 0.5 Typ. Max. 0.5 VDD =4.55.5V Units s
tR tRW
tR tRW
tR tRW
OPTREX CORPORATION
Page 11/23
2.4. Lighting Specifications 2.4.1. Absolute Maximum Ratings Ta=25C Parameter Foward Current Reverse Voltage LED Power Dissipation Symbol IF VR PD Conditions Note 1 Min. Typ. Max. 120 5 480 Units mA V mW
IF (mA) 120
48
-20
25
70
Ta ( C)
2.4.2. Operating Characteristics Parameter Foward Voltage Luminance of Module Surface Symbol VF L Conditions IF =60mA IF =60mA Min. 70 Typ. 3.5 100 Max. 4.0 Units V cd/m2
OPTREX CORPORATION
Page 12/23
3. Optical Specifications
3.1. LCD Driving Voltage Parameter Recommended LCD Driving Voltage Note 1 VDD -V 5 Symbol Conditions Ta= -20C Ta=25C Ta=70C Min. 12.0 11.5 Typ. 12.9 Max. 14.3 13.8 Units V V V
Note 1 : Voltage (Applied actual waveform to LCD Module) for the best contrast. The range of minimum and maximum shows tolerance of the operating voltage. The specified contrast ratio and response time are not guaranteed over the entire range. 3.2. Optical Characteristics Ta=25C, 1/65 Duty, 1/9 Bias, VOD =12.9V (Note 4), = 0, =- Parameter Contrast Ratio Viewing Angle Response Time Rise Note 2 Decay Note 3 TON TOFF Note 1 Symbol CR Conditions = 0C , =- Min. Typ. 60 Max. Units
Note 1 :Contrast ratio is definded as follows. (CR = LON / LOFF) LON : Luminance of the ON segments LOFF: Luminance of the OFF segments Measuring Spot : 3.0mm Note 2 :The time that the luminance level reaches 90% of the saturation level from 0% when ON signal is applied. Note 3 :The time that the luminance level reaches 10% of the saturation level from 100% when OFF signal is applied. Note 4 :Definition of Driving Voltage VOD Assuming that the typical driving waveforms shown below are applied to the LCD Panel at 1/A Duty - 1/B Bias (A: Duty Number, B: Bias Number). Driving voltage VOD is definded as the voltage VO-P when the contrast ratio (CR=LON / LOFF) is at its maximum.
VO-P
OPTREX CORPORATION
Page 13/23
3.3. Definition of Viewing Angle and Optimum Viewing Area *Point shows the point where contrast ratio is measured. : = 0, =- *Driving condition: 1/65 Duty, 1/9 Bias, VOD =12.9V, fF =84.6Hz
90 135 45
180 ( = 0 )
90
10 20 30 40 50
180
225 270
315 270
*Area
Computer
OPTREX CORPORATION
Page 14/23
4. I/O Terminal
4.1. Pin Assignment CN1 No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 Symbol CS1 RES A0 WR RD D0 D1 D2 D3 D4 D5 D6(SCL) D7(SI) VDD VSS VOUT C3C1+ C1C2C2+ V1 V2 V3 V4 V5 VR Chip Select Signal L : Active Reset Signal L : Reset H : D0~D7 are Display Data L : D0~D7 are Instructions 80 family CPU : Write Signal L : Active 80 family CPU : Read Signal L : Active Display Data Display Data Display Data Display Data Display Data Display Data Display Data(Serial Data Clock Signal Input) Display Data(Serial Data Input) Power Supply for Logic Power Supply ( 0V, GND ) DC/DC Voltage Converter Output DC/DC Voltage Converter Negative Connection DC/DC Voltage Converter Positive Connection DC/DC Voltage Converter Negative Connection DC/DC Voltage Converter Negative Connection DC/DC Voltage Converter Positive Connection Power Supply for LCD Drive V1 = 1/9V5 Power Supply for LCD Drive V2 = 2/9V5 Power Supply for LCD Drive V3 = 7/9V5 Power Supply for LCD Drive V4 = 8/9V5 Power Supply for LCD Drive V5, VOUT Voltage Adjustment Pin Applies voltage between VCC and V5 using a resistive divider. 28 29 30 CN2 No. 1 2 Symbol LED A LED K LED Anode Terminal LED Cathode Terminal Function C86 P/S NC Interface Mode Select Signal H : 68 series L : 80 series Parallel/Serial Data Select Signal H : Parallel L : Serial Non-connection Function
OPTREX CORPORATION
Page 15/23
CS1 RES A0 WR RD D0D7 VDD VSS VOUT C3C1+ C1C2C2+ V1 V2 V3 V4 V5 VR C86 P/S NJU6676
SEG 128 COM 64 8
Control LSI
OPTREX CORPORATION
Page 16/23
5. Test
No change on display and in operation under the following test condition. Conditions: Unless otherwise specified, tests will be conducted under the following condition. Temperature: 205C Humidity : 655%RH tests will be not conducted under functioning state. Parameter High Temperature Operating Low Temperature Operating High Temperature Storage Low Temperature Storage Damp Proof Test Vibration Test Conditions 70C2C, 96hrs (operation state) -20C2C, 96hrs (operation state) 80C2C, 96hrs -30C2C, 96hrs 40C2C,90~95%RH, 96hrs Total fixed amplitude : 1.5mm Vibration Frequency : 10~55Hz One cycle 60 seconds to 3 directions of X, Y, Z for each 15 minutes 7 Shock Test To be measured after dropping from 60cm high on the concrete surface in packing state.
Dropping method corner dropping F E B 60cm Concrete Surface G D A C A corner : once Edge dropping B,C,D edge : once Face dropping E,F,G face : once
No. 1 2 3 4 5 6
Notes
1 2 1,2 1,2 3
Note 1 :No dew condensation to be observed. Note 2 :The function test shall be conducted after 4 hours storage at the normal Temperature and humidity after removed from the test chamber. Note 3 :Vibration test will be conducted to the product itself without putting it in a container.
OPTREX CORPORATION
Page 17/23
6. Appearance Standards
6.1. Inspection conditions The LCD shall be inspected under 40W white fluorescent light. The distance between the eyes and the sample shall be more than 30cm. All directions for inspecting the sample should be within 45against perpendicular line.
45
A Zone : Active display area B Zone : Out of active display area ~ Maximum seal line C Zone : Rest parts A Zone + B Zone = Validity viewing area
OPTREX CORPORATION
Page 18/23
6.3. Standards(middle scale, LED) D = ( Long + Short ) / 2 No. 1 Parameter The Shape of Dot (1) Pin Hole Dimension D 0.10 0.10 < D 0.20 Acceptable Number * 1 pc / dot or less 5 pcs / cell or less Criteria * : Disregard Units : mm
1.Dot Type Dimension A A0.10 Acceptable Number * (Should not be connected to next dot) 1 pc / dot(only segment)or less B 0.10<A0.15 5 pcs / cell or less (Should not be connected to next dot) B 0.15 *
2.Defective type extends over multiple numbers of dots Dimension D0.10 Acceptable Number * 1 pc / dot(only segment)or less 0.10<D0.20 5 pcs / cell or less (Individual dot must secure 1/2 area or more)
OPTREX CORPORATION
Page 19/23
D = ( Long + Short ) / 2 No. 2 Parameter Black and White Spots, Foreign Substances Dimension D 0.10 0.10< D 0.20 0.20< D 0.30 (1) Round Shape Zone A * 6 4 Criteria
* : Disregard Units : mm
Acceptable Number B * 6 4 C * * *
(2) Line Shape Zone Length * L 2.0 L 1.0 * 0.10<W Width W 0.03 0.03<W0.05 0.10 A * 5 4 Acceptable Number B * 5 4 C * * * *
Zone Dimension D 0.30 0.30< D 0.40 0.40< D 0.60 No more than 3pcs as total. A * 3 2
Acceptable Number B * * 3 C * * *
5 6
Not to be conspicuous defects. If the stains are removed easily from LCDP surface, the module is not defective.
Black spots, line shaped foreign substances or air bubbles between glass & polarizer should be 9pcs maximum in total. 20mm or more
OPTREX CORPORATION
Page 20/23
Factory Control Number (0~99) Date of the week (A~G) Factory Number (0~9) Factory Code (Alphabet) Production Week (1~5) Production Month (1~9, X, Y, Z) Production Year (Lower 2 digits)
8. Type Number
The type number of module is specified as follows. F-51852GNFQJ-LW-AAN
9. Applying Precautions
Please contact us when questions and/or new problems not specified in this Specifications arise.
OPTREX CORPORATION
Page 21/23
OPTREX CORPORATION
Page 22/23
10) Models which use flexible cable, heat seal, or TAB: 1. In order to maintain reliability, do not touch or hold by the connector area. 2. Avoid any bending, pulling, or other excessive force, which can result in broken connections. 11) In case of buffer material such as cushion / gasket is assembled into LCD module, it may have an adverse effect on connecting parts ( LCD panel-TCP / HEAT SEAL / FPC / etc., PCB-TCP / HEAT SEAL / FPC etc., TCP-HEAT SEAL, TCP-FPC, HEAT SEAL-FPC, etc.,) depending on its materials. Please check and evaluate these materials carefully before use. 12) In case of acrylic plate is attached to front side of LCD panel, cloudiness ( very small cracks ) can occur on acrylic plate, being influenced by some components generated from polarizer film.. Please check and evaluate those acrylic materials carefully before use.
11. Warranty
This product has been manufactured to your companys specifications as a part for use in your companys general electronic products. It is guaranteed to perform according to delivery specifications. For any other use apart from general electronic equipment, we cannot take responsibility if the product is used in medical devices, nuclear power control equipment, aerospace equipment, fire and security systems, or any other applications in which there is a direct risk to human life and where extremely high levels of reliability are required. If the product is to be used in any of the above applications, we will need to enter into a separate product liability agreement. 1. We cannot accept responsibility for any defect, which may arise from additional manufacturing of the product (including disassembly and reassembly), after product delivery. 2. We cannot accept responsibility for any defect, which may arise after the application of strong external force to the product. 3. We cannot accept responsibility for any defect, which may arise due to the application of static electricity after the product has passed your companys acceptance inspection procedures. 4. When the product is in CFL models, CFL service life and brightness will vary According to the performance of the inverter used, leaks, etc. We cannot accept responsibility for product performance, reliability, or defect, which may arise. 5. We cannot accept responsibility for intellectual property of a third party, which may arise through the application of our product to your assembly with exception to those issues relating directly to the structure or method of manufacturing of our product. 6. Optrex will not be held responsible for any quality guarantee issue for defect products judged as Optrex-origin longer than 2 (two) years from Optrex production or 1(one) year from Optrex, Optrex America, Optrex Europe delivery which ever comes later.
OPTREX CORPORATION
Page 23/23