Académique Documents
Professionnel Documents
Culture Documents
81
OVERVIEW
Threaded rod FIS A, zinc-plated steel Approved in conjunction with FIS V/FIS VS/FIS VW: Concrete C20/25 and C50/60 Suitable in conjunction with FIS VS and FIS EM: Concrete C12/15 For xing of: Steel constructions in general Supports Rails High-racks Consoles
64 page
DESCRIPTION
Specially for use with Injection mortars FIS V, FIS VS or FIS VT in non-cracked concrete. The anchor rods are also suitable for push-through installation, using special push-through elements. The mortar bonds the entire surface of the anchor rod to the wall of the drilled hole and largely seals the hole. Anchor rod made of stainless steel A4 for outdoor use and in damp conditions.
Advantages/Benets
High-performance mortars allow high loads in non-cracked concrete. Various setting depths for dierent load levels and useful lengths. Quick manual installation without a setting tool reduces the work involved. Simple and quick push-through installation reduces installation time. Steel grade 5.8 or A4-70 guarantee the highest steel load-bearing strength and maximum permissible bending moments.
INSTALLATION
Type of installation
Pre-positioned installation Push-through installation (with scher push-through element)
Pre-positioned installation
Installation tips
Drill the hole. Observe the desired Push-through installation setting depth / usable length. Clean the drill-hole thoroughly (blow out 4 x, brush out 4 x, blow out 4 x) 18 mm with compressed air. Fill with the dened mortar quantity from the bottom of the drill-hole. If necessary screw the push-through element into position up Bear in mind the curing time of the injection mortar. to the depth marking. Install the building component. Observe the installation Then press the threaded rod down to the bottom of the hole torque indicated in the technical data sheet. (without setting tool), turning it slightly while doing so. Brushes BS see page 83.
FIXING PRINCIPLES
STANDARDS
In detail: The general principles for installation, the correct drilling procedure and much more on page 26.
You will find everything that has standards on page 34 under the keyword approvals.
Chemical xings
82
CHEMICAL FIXINGS
Chemical xings
ETA Type Art.-No. Art.-No. d0 [mm] hef, min [mm] tx1 - hef, min [mm] hef, max [mm]
FIS A M 6 x 75 FIS A M 6 x 85 FIS A M 6 x 110 FIS A M 8 x 90 FIS A M 8 x 110 FIS A M 8 x 130 FIS A M 8 x 175 FIS A M 10 x 110 FIS A M 10 x 130 FIS A M 10 x 150 FIS A M 10 x 200 FIS A M 12 x 140 FIS A M 12 x 160 FIS A M 12 x 180 FIS A M 12 x 210 FIS A M 12 x 260 FIS A M 16 x 175 FIS A M 16 x 200 FIS A M 16 x 250 FIS A M 16 x 300 FIS A M 20 x 245 FIS A M 20 x 290 FIS A M 24 x 290 FIS A M 24 x 380 FIS A M 30 x 340 FIS A M 30 x 430
90243 90272 90273 90274 90275 90276 90277 90278 90279 90281 90282 90283 90284 90285 90286 90287 90288 90289 90290 90291 90292 90293 90294 90295 90296 90297
90437 90438 90439 90440 90441 90442 90443 90444 90447 90448 90449 90450 90451 90452 90453 90454 90455 90456 90457 90458 90459 90460 90461 90462 90463 90464
8 8 8 10 10 10 10 12 12 12 12 14 14 14 14 14 18 18 18 18 24 24 28 28 35 35
50 50 50 64 64 64 64 80 80 80 80 96 96 96 96 96 125 125 125 125 160 160 192 192 240 240
66 72 72 80 96 96 96 97 117 120 120 124 144 144 144 144 154 172 192 192 219 240 260 288 303 360
1 5 30 1 5 25 70 1 1 19 69 2 2 22 52 102 3 3 40 90 4 28 4 66 5 38
Type
Art.-No.
PZ approval ETA
thread M
pcs.
Push-through element M 8 x 3 A4 Push-through element M 10 x 3 A4 Push-through element M 10 x 8 A4 Push-through element M 12 x 4 A4 Push-through element M 12 x 10 A4 Push-through element M 16 x 5 A4 Push-through element M 16 x 10 A4 Push-through element M 20 x 10 A4
9 6 3 0 7 4 1 7
M8 M 10 M 10 M 12 M 12 M 16 M 16 M 20
10 10 10 10 10 10 10 10
FIRE PREVENTION
CORROSION
Red hot: You will find fire prevention information on page 31.
Rust prevention tips: Everything you need to know about corrosion and how to prevent it is on page 32.
83
TECHNICAL DATA
Cleaning brush for concrete Compressed-air cleaning gun ABP
Type
Art.-No.
ID
for thread M
pcs.
BS 8 BS 10 BS 12 BS 14 BS 18 BS 24 BS 28 BS 35 ABP
7 4 1 7 4 1 8 5 8
1 1 1 1 1 1 1 1 1
LOADS
Mean ultimate loads, design resistant and recommended loads for single anchors of scher Injection system FIS V, FIS VS and FIS VW used with treaded rods FIS A with large spacing and edge distance.
Non-cracked concrete Anchor size Kind of steel Steel grade hef, min Effektive anchorage depth hef, min ho Drill hole depth do Drill hole diameter Mean ultimate loads Nu and Vu [kN] Tensile Shear 0 Nu 90 Vu M6 5.8 [mm] [mm] [mm] [mm] gvz 8.8 A4 C 10.9 A4-70 1.4529 5.8 40 72 8 hef, min 9.1 hef, max 11.0* 16.0* 16.4 hef, min 5.0* 8.0* 9.1 hef, max 5.0* 8.0* 10.0* hef, min hef, max hef, min 4.0 hef, max 4.0 hef, min hef, max hef, min 2.9 hef, max 2.9 3.8 6.8 4.5 6.4 6.7 2.7 4.8 3.2 4.6 6.9 4.8 8.1 135 70 40 40 70 102 7 3.2 5.0 4.0 6.3 5.3 11.4 4.5 5.6 7.4 gvz 8.8 M8 A4 C 10.9 A4-70 1.4529 5.8 40 96 ho = hef 10 gvz 8.8 M 10 A4 C 10.9 A4-70 1.4529 5.8 40 120 12 gvz 8.8 M 12 A4 C 10.9 A4-70 1.4529 48 144 14 22.4 44.0* 67.0* 79.3 59.0* 21.1* 26.4 21.1* 33.7* 40.0* 29.5* 9.3 33.2 11.2 27.0 26.7 6.7 23.7 8.0 19.3 60.0 19.0 62.4 290 145 55 55 78 174 14
[kN] [kN]
15.4 19.0* 29.0* 36.9 9.2* 14.6* 15.4 9.2* 14.6* 17.0* 6.1 14.7 7.4 11.7 11.3 4.4 10.5 5.3 8.3 17.1 8.1 17.6 195 100 40 40 70 126 9
17.1 30.0* 46.0* 57.7 41.0* 14.5* 19.2 14.5* 23.2* 27.0* 20.3* 7.1 23.0 8.5 18.6 18.0 5.1 16.5 6.1 13.3 34.3 12.9 35.7 245 125 45 45 70 150 12
Design resistant loads NRd and VRd [kN] Tensile Shear 0 NRd 90 VRd [kN] [kN] 12.8 13.9 8.2 14.7 10.2 20.3 11.6 21.9 13.0 23.0 16.2 29.7 16.9 31.6 18.9 33.2 23.6
Recommended loads Nrec and Vrec [kN] Tensile Shear 0 Nrec 90 Vrec [kN] [kN] 9.2 9.9 5.9 11.9 10.5 7.3 14.9 14.5 8.3 22.3 15.7 9.3 23.8 16.5 11.6 29.7 21.2 12.1 38.9 22.5 13.5 42.1 23.7 16.9 52.6
Recommended bending moment Mrec [Nm] Mrec [Nm] 4.6 Component dimensions, minimum spacings and edge distances scr, Np [mm] Characteristic spacing Characteristic edge distance ccr, Np [mm] smin Minimum spacing 1) [mm] Minimum edge distance 1) cmin [mm] Minimum structural [mm] hef, min hmin component thickness [mm] hef, max Clearance hole in fixture df to be attached for [mm] pre-positioned installation Clearance hole in fixture to df be attached for [mm] push-through installation T inst Required torque [Nm] [scale unit] hef, min Mortar filling quantity [scale unit] hef, max
9 5 1 2
11 10 2 3
14 20 2 5
16 40 3 6
Chemical xings
84
CHEMICAL FIXINGS
Chemical xings
[kN] [kN]
Design resistant loads NRd and VRd [kN] Tensile Shear 0 NRd 90 VRd [kN] [kN] 14.4 53.6 34.5 49.3 35.1 10.3 38.3 24.6 35.2 25.1 26.4 108.6 63.3 70.6 113.0 110.7 79.1 18.8 77.6 45.2 79.0 36.9 160.2 88.5 98.7 112.2 179.5 176.0 125.8 157.0 26.3 114.4 63.2 80.1 128.2 125.7 89.8
50.2
43.8
49.0
78.4
54.9
68.6
Recommended loads Nrec and Vrec [kN] Tensile Shear 0 Nrec 90 Vrec [kN] [kN]
35.6 31.3 35.0 56.0 39.2 49.0 50.4 80.7 56.5 70.5 12.1 Recommended bending moment Mrec [Nm] Mrec [Nm] 98.9 152.0 158.1 106.7 133.1 193.1 296.6 308.6 207.9 259.4 333.1 512.0 533.3 359.4 448.6 668.0 1026.91070.0 720.7 899.4 Component dimensions, minimum spacings and edge distances scr, Np [mm] Characteristic spacing 370 450 525 640 Characteristic edge distance ccr, Np [mm] 185 225 265 320 smin [mm] 65 85 105 140 Minimum spacing 1) [mm] 65 85 105 140 Minimum edge distance 1) cmin Minimum structural [mm] hef, min 96 120 144 180 hmin component thickness [mm] hef, max 224 280 336 420 Clearance hole in fixture df to be attached for [mm] 18 22 26 33 pre-positioned installation Clearance hole in fixture df to be attached for [mm] 20 26 30 40 push-through installation T inst Required torque [Nm] 60 120 150 300 [scale unit] hef, min 4 10 14 26 Mortar filling quantity [scale unit] hef, max 11 29 42 79
* Steel failure decisive. For minimum spacing and minimum edge distance the above described loads have to be reduced (see fischer Technical Handbook or fischer Design software COMPUFIX). Values given above are valid under the following assumptions: - Sufficient mechanical cleaning of the drill hole using stainless steel brushes. - Dry concrete, temperature range 50 C long term temperature and 80 C short term temperature. All values apply for concrete C 20/25 without edge or spacing influences. Desing resistant loads: material safety factor M is included. Material safety factor M depends on the type of anchor. Recommended loads: material safety factor M and safety factor for load L = 1.4 are included.
1)
The condition of application dier from those given in the European Technical Approval (ETA). For further detailed information about the ETA please contact the scher technical service department. RG M threaded rods can be used as an alternative. Please refer to page 52 for suitable threaded rods.
85
OVERVIEW
Internal-threaded anchor RG MI, M5 - M20 zinc-plated steel Internal-threaded anchor RG MI, M8 - M20 stainless steel A4 Approved for: Non-cracked concrete C12/15 Suitable for: Natural stone with dense structure For xing of: Detachable connections with metrical screws in the steel, metal and plant construction.
DESCRIPTION
The xing system consists of the Internal- threaded anchor RG MI and the resin capsule R M. The resin capsule R M contains quick-curing styrene-free vinylester resin. Suitable for commercially-available metric screws and threaded rods. During setting, the edges of the internal threaded anchor destroy the capsule in the drill hole, mix and activate the resin. The resin adheres to the entire surface of the internal threaded anchor, bonding it to the wall of the drilled hole.
Advantages/Benets
High-performance resin guarantees high loads in noncracked concrete. The resin anchoring is free of expansion forces and permits low axial spacings and edge distances. Flush nish, no projecting bolt after dismantling the xture.
INSTALLATION
Type of installation
Pre-positioned installation Brushes see page 83.
TECHNICAL DATA
Internal-threaded anchor RG MI, zinc-plated steel
Type Art.-No. ID approval ETA drill do [mm] drill depth = mounting depth h0 = hs [mm] min. bolt penetration e2 [mm] max. bolt penetration e1 [mm] ts capsules
pcs.
RG 8 x 75 M 5 I RG 10 x 75 M 6 I RG 12 x 90 M8 I RG 16 x 90 M10 I RG 16 x 125 M12 I RG 22 x 160 M16 I RG 28 x 200 M20 I RG 12 x 90 M8 I A4 RG 16 x 90 M10 I A4 RG 18 x 125 M12 I A4 RG 22 x 160 M16 I A4 RG 28 x 200 M 20 I A4
48221 48222 50552 50553 50562 50563 50564 50565 50566 50567 50568 50569
6 3 6 3 5 2 9 6 3 0 7 4
10 12 14 18 20 24 32 14 18 20 24 32
8 10 12 15 18 24 30 12 15 18 24 30
14 16 18 23 26 35 45 18 23 26 35 45
50270 RM 8 50271 RM 10 50272 RM 12 50278 RM 14 79838 RM 16 E 79838 RM 16 E 50274 RM 20 50272 RM 12 50278 RM 14 79838 RM 16 E 79838 RM 16 E 50274 RM 20
78178 BS 10 78179 BS 12 78180 BS 14 78181 BS 16/18 52277 BS 20 78182 BS 24 78184 BS 35 78180 BS 14 78181 BS 16/18 52277 BS 20 78182 BS 24 78184 BS 35
10 10 10 10 10 5 5 10 10 10 5 5
FIXING PRINCIPLES
STANDARDS
In detail: The general principles for installation, the correct drilling procedure and much more on page 26.
You will find everything that has standards on page 34 under the keyword approvals.
Chemical xings
86
CHEMICAL FIXINGS
Chemical xings
16.7 11.7 11.9 8.3 17.1 7.3 18.1 270 135 40 40 120 12 18 9 10 5 10.2
22.2 18.6 15.9 13.3 34.3 11.6 35.7 270 135 45 45 125 15 23 12 20 7 16.2
17.5
27.0
18.9
23.6
12.5 38.9
19.3 60.0
13.5 42.1
16.9 52.6
32.6
50.2
35.1
43.9
50.9
60.7
54.9
68.6
23.3 98.9
35.8 152.0
25.1 106.2
31.3 132.6
36.3 192.6
43.4 296.6
39.2 207.9
49.0 259.4
* Steel failure decisive. 1) For minimum spacing and minimum edge distance the above described loads have to be reduced (see fischer Technical Handbook or fischer Design software COMPUFIX). Values given above are valid under the following assumptions: - Sufficient mechanical cleaning of the drill hole using stainless steel brushes. - Dry concrete, temperature range 50 C long term temperature and 80 C short term temperature. All values apply for concrete C 20/25 without edge or spacing influences. Desing resistant loads: material safety factor M is included. Material safety factor M depends on the type of anchor. Recommended loads: material safety factor M and safety factor for load L = 1.4 are included. The condition of application dier from those given in the European Technical Approval (ETA). For further detailed information about the ETA please contact the scher technical service department. RG M threaded rods can be used as an alternative. Please refer to page 48 for suitable threaded rods.