Académique Documents
Professionnel Documents
Culture Documents
FEATURES
Overvoltage Protection for 3.3V, 5V, and 12V Outputs. Power Good Signal for 5V Output. Remote ON/OFF Input. Uncommitted Protection Input. 5V Regulator with 25mA Source Current. 2.5V Precision Shunt Regulator. 8V to 16V Operation. Low Power Consumption.
DESCRIPTION
The AIC1686 is a supervisory and protection IC intended for use in off-line, multiple output power supplies. It consists of protection circuitry, power good indicator, remote ON/OFF control, and precision shunt regulator. The overvoltage protection (OVP) function is for 3.3V, 5V, and 12V outputs. In addition, an uncommitted fault detection input (PRIN) is available for use with other protection functions, such as overcurrent, undervoltage, and/or short-circuit protection of outputs. The shunt regulator has been included to implement the feedback control for one of the power supplys outputs. The noniverting input (EAI) is internally tied to a precision 2.5V reference. The power good circuit monitors the 5V output and asserts, with a programmable delay, a TTL compatible high logic level at its output after the 5V output reaches the regulation range. The delay is programmed by a timing capacitor connected to CPG pin of the IC. The power good circuit sets its output low before the 5V output goes out of regulation range. The remote ON/OFF function enables the power supply to be turned on and off from the secondary side by a switch.
APPLICATIONS
PC Off-Line Power Management.
4F, 9, Industry E. 9th Rd, Science Based Industrial Park, Hsinchu Taiwan, ROC TEL: 886-3-5772500 FAX: 886-3-5772510
www.analog.com.tw
AIC1686
ORDERING INFORMATION
AIC1686 XX PACKAGE TYPE N: PLASTIC DIP TEMPERATURE RANGE C: 0C~70C
ORDER NUMBER PIN CONFIGURATION
TOP VIEW PRIN 1 REMI 2 PG 3 V33 4 GND 5 V5 6 V12 7 EAO 8 16 CPG 15 FL 14 REMO 13 REF 12 VCC 11 CLS 10 LS 9 EAI
AC/DC CONVERTER
AC LINE SENSE
AIC1686
POWER GOOD
PWM CONTROLLER
OPTOISOLATOR OPTPISOLATOR
PROTECTION INPUT
REGULATION
PROTECTION O/P
REMOTE ON/OFF
Maximum Storage Temperature Range ...................................... -65C~150C Maximum Lead Temperature (Soldering 10 Sec) .................................... 300C Maximum Power Dissipation ........................................ 500mW (Derate at 10mW/C above 70C ambient)
AIC1686
TEST CIRCUIT
Refer to TYPICAL APPLICATION CIRCUIT.
TEST CONDITIONS
HYSRI
AIC1686
ELECTRICAL CHARACTERISTICS (CONTINUED)
PARAMETER
REMI Pull High Resistor REMO Output Low Voltage REMO Output High Voltage Power Good LS Input Clamp Voltage LS Input Rising Threshold LS Input Hysteresis Voltage CPG Timing Current CPG Input Hysteresis CPG Recharge Delay Time PG Output High Voltage PG Output Low Voltage Delay LS Falling to PG Falling Delay LS Rising to PG Rising Delay REMI Rising to PG Falling LS (L to H) IOH=5mA IOL=12mA CPG=1F CPG=1F V5=5V ILS=1mA CLS=5V VLSCMP VLSH HYSLS ICPGH HYSCPG TRCPG VPGOH VPGOL TPGF TPGR TRIPGF 150 52 300 1 450 4 0.4 1 6 7.8 8.8 6.2 1.2 9 0.4 6.7 1.6 12 9.8 V V V A V mS V V S mS S
TEST CONDITIONS
REMI=L REMI=H IOL=4.5mA IOH=500A
Note1: A 1F capacitor is connected between REF and GND to ensure a stable reference voltage.
AIC1686
TYPICAL PERFORMANCE CHARACTERISTICS
5.1
5.05
4.95
4.9
-10
10
20
30
40
50
60
70
80
90
100
10
20
30
Temperature (C)
Temperature (C)
40
50
60
70
80
90
100
50
Inverting Input Voltage Change with Output Sink Current of Error Amplifier
40
10
0C 25C
30
20
EAO=1V
100C
6
10
EAO=2.5V
0 0.01
0.1
10
4.5
4.7
4.9
5.1
5.3
5.5
350
10
12
Temperature (C)
AIC1686
BLOCK DIAGRAM
REF
EAI
EAO
2.5V
+ S R Q REF REF FL
25S Delay
PRIN 60K
Power ON Reset
CPG V5 10K
AIC1686
PIN DESCRIPTIONS
IN 1: PRIN - Auxiliary protection logic input to fault latch. HIGH for 25S to set latch and cause FL output to go LOW. Internally active down for normal operation. PIN 2: REMI - Logic input for remote ON/OFF control power supply. LOW= REMOTE ON, HIGH=REMOTE OFF. In remote off state this chip goes into standby mode, FL=HIGH, REMO = LOW, and PG = LOW. PIN 3: PG - Power good output signal. High level indicates that power is good. PIN 4: V33 From 3.3V power supply. Used for overvoltage sensing only. PIN 5: GND - Ground pin. Connect to ground on secondary side. PIN 6: V5 - From 5V power supply. Used for overvoltage sensing as well as internal supply for certain specific functions. PIN 7: V12 - From 12V power supply. Used for overvoltage sensing only. PIN 8: EAO - Output of the error amplifier. Can be used to drive an opto-isolator. PIN 9: EAI - Inverting input of the error amplifier, used to close voltage feedback loop. PIN 10: LS AC line sense input signal. PIN 16: CPG PIN 11: CLS - Timing capacitor used to help ensure that a falling LS voltage is detected before power supply outputs fall out of regulation. PIN 12: VCC- VCC supply input to IC. This should be a DC voltage between 8 and 16V. PIN 13: REF - +5V precision reference output. May be used to supply up to 25mA to external circuitry. PIN 14: REMO- Remote ON/OFF output that indicates the state of the power supply. HIGH = REMOTE ON, LOW=REMOTE OFF. This is essentially the inverse of the REMI input voltage. PIN 15: FL - Fault output that indicates the fault condition. HIGH = NORMAL, LOW = FAULT. When fault states the PG goes LOW. -Timing capacitor that sets the delay from +5V main coming up to PG signal being asserted High.
TPGR 2 . 5 CCPG ICPGH
Use rectified output from main power 2mA. transformer. Internally clamped to 9V and sinks up to
pulled
AIC1686
PACKAGE DIMEMSION
16 LEAD PLASTIC DIP (unit: mm)
D
SYMBOL A1
E1
A2 b
E
C D E
C
A2 A1 L eB b e
E1 e eB L
2.54(TYP)
This datasheet has been download from: www.datasheetcatalog.com Datasheets for electronics components.